Dixon 966985401 Lawn Mower Operator Manual
જાહેરાત
જાહેરાત
Operator Manual
Ram Ultra 61, 25 KOH / 966985401
Ram Ultra 61, 25 KOH BF / 966985402
Please read the operator manual carefully and make sure you understand the instructions before using the machine.
In order to implement improvements, specifications and designs can be altered without prior notification.
Note that no legal demands can be placed based on the information contained in these instructions.
Use only original parts for repairs. The use of other parts voids the warranty.
Do not modify or install non-standard equipment to the unit without consent from the manufacturer. Modifications to the unit may cause unsafe operations or damage the unit.
When this product is worn out and no longer used, it should be returned to the reseller or other party for recycling.
©2009 HTC All rights reserved.
Beatrice, NE. Printed in U.S.A.
IntRoDUCtIon................................................................ 5
General........................................................................ 5
Driving.and.transport.on.Public.Roads....................... 5 towing......................................................................... 5 operating..................................................................... 5
Good.service............................................................... 6
Manufacturing.number...................................... 6 sYMBoLs.AnD.DeCALs.................................................. 7 sAFetY............................................................................. 9 safety.Instructions....................................................... 9
Personal.safety.equipment....................................... 11 slope.operation......................................................... 11 safe.Handling.of.Gasoline......................................... 13
General.Maintenance................................................ 14 transport................................................................... 16 towing....................................................................... 16 spark.Arrestor............................................................ 16
ContRoLs..................................................................... 17
Control.Locations....................................................... 17 steering.Control.Levers............................................. 18
Parking.Brake............................................................ 19 throttle.Control.......................................................... 19
Ignition.switch............................................................ 19
Choke.Control............................................................ 20
Blade.switch.............................................................. 20
Fuses......................................................................... 20
Hour.Meter................................................................. 21
Cutting.Height.Adjuster.............................................. 21
Fuel.shut.off.Valve.................................................... 22 tracking..................................................................... 22
Fuel.tank................................................................... 23 oPeRAtIon.................................................................... 24 training...................................................................... 24 steering..................................................................... 24
Before.starting........................................................... 25 starting.the.engine.................................................... 25
Weak.Battery............................................................. 28
Jumper.cables................................................. 28
Running..................................................................... 29 operating.on.Hills..................................................... 30
Contents
Mowing.tips............................................................... 31 stopping.the.engine.................................................. 32
Manual.transport....................................................... 33
Pump.Release.Valves..................................... 33
MAIntenAnCe............................................................... 34
Maintenance.schedule.............................................. 34
Battery....................................................................... 36 safety.system............................................................ 37 tire.Pressures........................................................... 37
Parking.Brake............................................................ 37
V-belts........................................................................ 38
Deck.Belt......................................................... 38
Pump.Belt........................................................ 39
Cutting.Blades........................................................... 39
Blade.Replacement......................................... 40
Adjusting.the.Mower.Deck......................................... 41
Leveling........................................................... 41
Anti-scalp.Rollers............................................ 42
Caster.Wheels........................................................... 43
Cleaning..................................................................... 43
Hardware................................................................... 43
LUBRICAtIon................................................................. 44
Front.Wheel.Mount.................................................... 45
Front.Wheel.Bearings................................................ 45
Deck.spindle.................................................... 45 engine.Lubrication..................................................... 45
Hydraulic.Pump......................................................... 46
Fluid.Change................................................... 46
Purging............................................................ 46 tRoUBLesHootInG..................................................... 47
Winter.storage........................................................... 49 stoRAGe........................................................................ 49 sCHeMAtICs.................................................................. 50 teCHnICAL.DAtA........................................................... 51 torque.specifications................................................ 51
ConFoRMItY.CeRtIFICAtes...................................... 54
WARRAntY..................................................................... 55 seRVICe.JoURnAL........................................................ 56
WARNING!
Failure to follow cautious operating practices can result in serious injury to the operator or other persons. The owner must understand these instructions, and must allow only trained persons who understand these instructions to operate the mower.
Each person operating the mower must be of sound mind and body and must not be under the influence of any mind altering substance.
WARNING!
Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
WARNING!
Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
IntRoDUCtIon
Congratulations
Thank you for purchasing a Dixon ride-on mower.
This machine is built for superior efficiency to rapidly mow primarily large areas. A control panel easily accessible to the operator and a hydrostatic transmission regulated by steering controls both contribute to the machine’s performance.
This manual is a valuable document. Read the contents carefully before using or servicing the machine. The following of instructions (use, service, maintenance, etc.) by all who operate this machine is important for the safety of the operator and others.
It can also considerably increase the life span of the machine and increase its resale value.
If you sell your machine, be sure to give the operator’s manual to the new owner.
The final chapter of this operator’s manual provides a
Service Journal. Ensure that service and repair work are documented. A well-kept service journal reduces service costs for the maintenance and affects the machine’s resale value. Please contact your dealer for more information. Take the operator’s manual along when the machine is taken to your dealer for service.
General
In this operator’s manual, left and right, backward and forward are used in relation to the machine’s normal driving direction.
Continuous dedication to improve our products require that specifications and design are subject to change without notice.
Driving and Transport on Public Roads
Check applicable road traffic regulations before transporting on public roads. If the machine is transported, you must always use approved fastening equipment and ensure that the machine is well anchored. DO NOT operate this machine on public roadways.
Towing
If machine is equipped with a tow hitch, use extreme caution when towing. Never allow children or others in or on towed equipment.
Make wide turns to avoid jack-knifing. Travel slowly and allow extra distance to stop. Do not tow on sloped ground. The weight of the towed equipment may cause loss of traction and loss of control.
Follow the manufacturer’s recommendation for weight limits for towed equipment. Do not tow near ditches, canals, and other hazards.
Operating
This machine is constructed only for mowing grass on lawns and even ground without obstacles such as stones, tree stumps, etc. The machine can also be used for other tasks when equipped with special accessories provided by the manufacturer. Operating instructions for the accessories are provided with delivery. All other types of uses are incorrect. The manufacturer’s directions concerning operation, maintenance, and repairs must be carefully followed.
Lawn mowers and all power equipment, can be potentially dangerous if used improperly. Safety requires good judgement, careful use in accordance with these instructions and common sense.
The machine must only be operated, maintained, and repaired by persons familiar with the machine’s special characteristics and who are also knowledgeable about the safety instructions. Use only approved repair parts to maintain this machine.
Accident prevention regulations, other general safety regulations, occupational safety rules, and traffic regulations must be followed without fail.
Unauthorized modifications to the design of the machine may absolve the manufacturer from liability for any resulting personal injury or property damage.
5
IntRoDUCtIon
Good Service
Dixon’s products are sold only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service.
Before the product is delivered, the machine has, for example, been inspected and adjusted by your retailer. See the certificate in the Service Journal in this operator’s manual.
When you need spare parts or support in service questions, warranty issues, etc., please consult the following professional:
This Operator’s Manual belongs to the machine with the manufacturing number:
Manufacturing Number
The machine’s manufacturing number can be found on the printed plate affixed to the left in the engine compartment. Stated on the plate, from the top are:
•
•
The machine’s type designation (I.D.).
The manufacturer’s type number (Model).
• The machine’s serial number (Serial no.)
Please have the type designation and serial number available when ordering spare parts.
The engine’s manufacturing number is stamped on one of the valve covers.
The plate states:
• The engine’s model.
• The engine’s type.
• Code
Please have these available when ordering spare parts.
The wheel motors and hydrostatic pumps have a barcode decal affixed at the rear.
Engine Transmission
6
sYMBoLs.AnD.DeCALs
These symbols are found on the machine and in the operator’s manual.
Study them carefully so that you know what they mean.
WARNING!
Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx.
Used in this publication to notify the reader of a risk of personal injury or death, particularly if the reader should neglect to follow instructions given in the manual.
IMPORTANT INFORMATION
Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx.
Used in this publication to notify the reader of a risk of material damage, particularly if the reader should neglect to follow instructions given in the manual.
Used also when there is a potential for misuse or misassembly.
R N
Reverse Neutral Fast Slow Choke Fuel
Warning! Parking Brake CE conformity marking. Only for
European market
Warning! Rotating blades, Do not touch parts keep away from the discharge deck
Battery acid is corrosive, explosive and flammable Do not stand here
Noise emissions to the surroundings in accordance with the European Union’s directive.
The machine’s emission is stated in the chapter TECHNICAL DATA and on the decals.
Only machines for European market.
Use protective glasses Use protective gloves
7
8 sYMBoLs.AnD.DeCALs
Read
Operator’s
Manual
Shut off engine and remove key before performing any maintenance or repair work
Keep a safe distance from the machine
Use on slopes no greater than 10°
No passengers
Whole body exposure to thrown objects
Severing of fingers and toes
Do not open or remove safety shields while engine is running
Careful backing up, watch for other people
Careful going forward, watch for other people
Moving sharp blades under cover
sAFetY
Safety Instructions
These instructions are for your safety. Read them carefully.
WARNING!
THIS CUTTING MACHINE IS CAPABLE
OF AMPUTATING HANDS AND FEET
AND THROWING OBJECTS. FAILURE
TO OBSERVE THE FOLLOWING
SAFETY INSTRUCTIONS COULD
RESULT IN SERIOUS INJURY OR
DEATH.
General Operation
• Read, understand, and follow all instructions on the machine and in the manual before starting.
•
•
•
•
Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times.
Only allow responsible adults, who are familiar with the instructions, to operate the machine.
Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blades.
Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area.
•
•
•
•
•
•
•
Never carry passengers. The machine is only intended for use by one person.
Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing.
Never direct discharged material toward anyone.
Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the blades when crossing gravel surfaces.
Do not operate machine without the entire grass catcher, discharge guard, or other safety devices in place and working
Slow down before turning.
Never leave a running machine unattended.
Always turn off blades, set parking brake, stop engine, and remove keys before dismounting.
Disengage blades when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grass catcher, or unclogging the discharge guard.
WARNING!
This symbol means that important safety instructions need to be emphasized. It concerns your safety.
8011-512
Read the operator’s manual before starting the machine
Clear the area of objects before mowing
8011-513
9
sAFetY
•
•
•
•
•
•
•
•
•
•
Operate machine only in daylight or good artificial light.
Do not operate the machine while under the influence of alcohol or drugs.
Watch for traffic when operating near or crossing roadways.
Use extra care when loading or unloading the machine into a trailer or truck.
Always wear eye protection when operating machine.
Data indicates that operators age 60 years and above are involved in a large percentage of riding mower-related injuries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury.
Follow the manufacturer’s recommendation for wheel weights or counterweights.
Anyone who operates this machine must first read and understand this Operation Manual. Local laws may regulate the age of the user.
Keep machine free of grass, leaves or other debris buildup which can touch hot exhaust or engine parts and burn. Do not allow the mower deck to plow leaves or other debris which can cause buildup to occur. Clean any oil or fuel spillage before operating or storing the machine.
Allow machine to cool before storage.
Never take passengers
8011-520
WARNING!
Engine exhaust and certain vehicle components contain or emit chemicals considered to cause cancer, birth defects, or other reproductive system damage. The engine exhaust contains carbon monoxide, which is an odorless, colorless, poisonous gas. Do not use the machine in enclosed spaces.
10
sAFetY
Personal Safety Equipment
WARNING!
When using the machine, approved personal protective equipment (shown in illustrations) shall be used. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your retailer for help in choosing the right equipment.
•
•
•
•
•
•
•
Make sure that you have first aid equipment close at hand when using the machine.
Never use the machine when barefoot.
Always wear protective shoes or boots, preferably with steel toe caps.
Always wear approved protective glasses or a full visor when assembling or driving.
Always wear gloves when handling the blades.
Never wear loose clothing that can get caught in moving parts.
Use ear protectors to avoid damage to hearing.
Slope Operation
Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Operation on all slopes requires extra caution.
If you cannot back up the slope or if you feel uneasy on it, do not mow it.
• Mow up and down slopes (10 degrees maximum), not across.
•
•
•
•
•
•
•
•
•
Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain could overturn the machine. Tall grass can hide obstacles.
Choose a low ground speed so that you will not have to stop while on the slope.
Do not mow on wet grass. Tires may lose traction.
Avoid starting, stopping, or turning on a slope. If the tires lose traction, disengage the blades and proceed slowly straight down the slope.
Keep movement on the slopes slow and gradual.
Do not make sudden changes in speed or direction, which could cause machine to roll over.
Use extra care while operating machine with grass catchers or other attachments; they can affect the stability of the machine.
Do not use on steep slopes.
Do not try to stabilize the machine by putting a foot on the ground.
Do not mow near drop-offs, ditches, or embankments. The machine could suddenly roll over if a wheel is over the edge or if the edge caves in.
Personal protective equipment
Mow up and down, not side to side
8011-670a
6003-004
WARNING!
Do not drive up or down hills with slopes greater than 10 degrees. Do not drive across any slopes.
11
sAFetY
Children
Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity.
Never assume that children will remain out of the path of danger.
•
•
Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator.
Be alert and turn machine off if a child enters the area.
•
•
•
•
Before and while backing, look behind and down for small children.
Never carry children, even with the blades shut off. They may fall off and be seriously injured or interfere with safe machine operation. Children who have been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine.
Never allow children to operate the machine.
Use extra care when approaching blind corners, shrubs, trees, or other objects that may block the view of a child.
Keep children away from work area
8011-518
Never allow children to operate the machine
8011-517
12
sAFetY
WARNING!
The engine must not be started when the driver’s floor plate or any protective plate for the mower deck’s drive belt is removed.
•
•
•
Safe Handling of Gasoline
To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive.
• Extinguish all cigarettes, cigars, pipes, and other sources of ignition.
•
•
•
•
•
•
•
•
•
•
•
Use only approved gasoline container.
Never remove gas cap or add fuel with the engine running. Allow engine to cool at least two (2) minutes before refueling.
Never fuel the machine indoors.
Never store the machine or fuel container where there is an open flame, spark, or pilot light such as on a water heater or other appliance.
Before beginning to refuel, minimize the risk of static electricity by touching a metal surface.
Never fill containers inside a vehicle or on a truck or trailer bed with plastic liner. Always place containers on the ground away from the vehicle when filling.
Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle.
Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.
If fuel is spilled on clothing, change clothing immediately.
Never overfill fuel tank. Replace gas cap and tighten securely.
Do not start the engine near spilled fuel.
Never use gasoline as a cleaning agent.
If leaks arise in fuel system, engine must not be started until problem has been resolved.
Check the fuel level before each use and leave space for the fuel to expand, as the heat from the engine and the sun may otherwise cause the fuel to expand and overflow.
Never fill the fuel tank indoors
8011-516
WARNING!
The engine and the exhaust system become very hot during operation.
There is risk for burns if touched.
Allow engine and exhaust system to cool at least two (2) minutes before refueling.
13
sAFetY
General Maintenance
• Never operate machine in a closed area.
• Keep all nuts and bolts tight to be sure the equipment is in safe working condition.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Never tamper with safety devices. Check their proper operation regularly.
Keep machine free of grass, leaves, or other debris buildup. Clean oil or fuel spillage and remove any fuel-soaked debris. Allow machine to cool before storing.
If the machine strikes a foreign object, stop and inspect the machine. Repair, if necessary, before restarting.
Never make any adjustments or repairs with the engine running.
Check grass catcher components and the discharge guard frequently and replace with manufacturer’s recommended parts, when necessary.
Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them.
Check brake operation frequently. Adjust and service as required.
Maintain or replace safety and instruction labels, as necessary.
Do not modify safety equipment. Check regularly to be sure it works properly. The machine must not be driven with defective or unmounted protective plates, protective cowlings, safety switches, or other protective devices.
Do not change the settings of governors and avoid running the engine with overly high engine speeds. If the engine runs too fast, there is risk for damaging the machine components.
Be very careful when handling battery acid. Acid on skin can cause serious corrosive burns. If battery acid is spilled on skin, rinse immediately with water.
Acid in the eyes can cause blindness, contact a doctor immediately.
Be careful when servicing the battery. Explosive gases form in the battery. Never perform maintenance on the battery when smoking or near open flames or sparks.
The battery can explode and cause serious injury or damage.
Ensure that the equipment is in good condition and that all nuts and bolts, especially those fastening the blade attachments, are properly tightened and torqued.
14
Never drive the machine in an enclosed space
WARNING!
Use protective glasses for maintenance work.
8011-515
WARNING!
The battery contains lead and lead compounds, chemicals that are considered to cause cancer, birth defects, and other reproductive system damage. Wash your hands after handling the battery.
sAFetY
Sparking can occur when working with the battery and the heavy cables of the starter circuit. This can cause battery explosion, fire or eye injury. Sparking in this circuit can not occur after the chassis cable
(normally negative, black) is removed from the battery.
• Use protective goggles.
• Ensure that the fuel filler cap is mounted tightly and no flammable substances are stored in an open vessel.
WARNING!
Avoid electrical sparking and its consequences by the following routines:
•
•
•
•
•
•
•
•
•
•
•
•
•
Never work with the starter circuit if there is spilled fuel.
Disconnect the negative cable from the battery first and reconnect it last.
Do not make a bridge short circuit across the starter relay to run the starter.
Never use the machine indoors or in spaces lacking proper ventilation. The exhaust fumes contain carbon monoxide, an odorless, poisonous, and lethal gas.
Stop to inspect the equipment if the machine runs over or into anything. If necessary, make repairs before starting.
Never make adjustments with the engine running.
The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer. Only use approved repair parts for the machine.
The blades are sharp and can cause cuts and gashes. Wrap the blades or use protective gloves when handling them.
Check the parking brake’s functionality regularly.
Adjust and service as necessary.
The mulch blades should only be used in familiar areas when higher quality mowing is desired.
Reduce the risk of fire by removing grass, leaves, and other debris that may have accumulated on the machine.
Allow the machine to cool before putting it in storage.
Regularly clean deck and underside of deck, avoid spraying engine and electrical components with water.
6003-009
Do not smoke when performing maintenance on the battery.
The battery can explode and cause serious injury/damage.
Risk of sparking
8009-728
Regularly clean deck
8011-514
15
sAFetY
Transport
• The machine is heavy and can cause serious crushing injuries. Be extra cautious when it is loaded on or unloaded from a vehicle or trailer.
• Use an approved trailer to transport the machine.
Activate the parking brake, turn off the fuel supply, and fasten the machine with approved fastening devices, such as bands, chains, or straps, when transporting.
•
•
•
•
Do not operate this machine on public roadways.
Check and abide by local traffic regulations before transporting the machine on any road.
Do not tow this machine: it may cause damage to the drive system.
Load the unit onto truck or trailer by driving up ramps of suitable strength using a slow speed. Do not lift! The machine is not intended to be lifted by hand.
Towing
If machine is equipped with a tow hitch, use extreme caution when towing. Never allow children or others in or on towed equipment..
Make wide turns to avoid jack-knifing. Travel slowly and allow extra distance to stop. Do not tow on sloped ground. The weight of the towed equipment may cause loss of traction and loss of control.
Follow the manufacturer’s recommendation for weight limits for towed equipment. Do not tow near ditches, canals, and other hazards.
Spark Arrestor
A spark arrestor for the muffler is available through your authorized Dixon dealer.
WARNING!
Escaping hydraulic oil under pressure can have sufficient force to penetrate the skin, causing serious injury. If injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if proper medical treatment is not administered immediately.
IMPORTANT INFORMATION
The parking brake is not sufficient to lock the machine in place during transport. Ensure that the machine is well fastened to the transport vehicle. Always reverse the machine onto the transport vehicle to avoid tipping it over.
WARNING!
This mower is equipped with an internal combustion engine and should not be used on or near any unimproved forested, bush covered or grassy lands unless the engine's system is equipped with a spark arrestor meeting applicable local or state laws (if any).
16
ContRoLs
This operator’s manual describes the Dixon Zero Turn
Rider. The rider is fitted with a Kohler 25 HP* fourstroke overhead valve engine.
Transmission from the engine is made via belt-driven hydraulic pumps. Using the left and right steering controls, the flow is regulated and thereby the direction and speed.
Control Locations
9 8 7 2
1
10
11
8050-912
6 12 3 5 4
1.
2.
3.
4.
Motion control levers
Parking brake
Throttle control
Blade switch
5.
6.
7.
8.
Ignition switch
Choke control
Fuses
Fuel tank cap
*The power rating of the engines indicated is the average net power output (at specified rpm) of a typical production engine for the engine model measured to SAE standard
J1349/ISO1585. Mass production engines may differ from this value. Actual power output for the engine installed in the final machine will depend on the operating speed, environmental conditions and other variables.
9. Fuel shut off valve
10. Deck lift
11. Seat adjustment lever
12. Hour meter
17
ContRoLs
Steering Control Levers
The machine’s speed and direction are continuously variable using the two steering controls. The steering controls can be moved forward or backward about a neutral position. Furthermore, there is a neutral position, which is locked if the steering controls are moved outward.
When both controls are in the neutral position (N), the machine stands still.
By moving both controls an equal amount forward or backward, the machine moves in a straight line forward or backward respectively.
In order, for example, to turn right while moving forward, move the right control towards the neutral position. The rotation of the right wheel is reduced and the machine turns to the right.
Zero turn can be achieved by moving one control backward (behind the neutral position) and carefully moving the other steering control forward from its neutral position. The rotation direction when zero turning is determined by which steering control is moved backward behind the neutral position. If the left steering control is pulled backward, the machine turns to the left. Use extra care when using this maneuver.
If the steering controls are in uneven positions when standing still or do not fit in the slots for moving the controls outward, they can be adjusted.
Steering controls
WARNING!
The machine can turn very rapidly if one steering control is moved much further forward than the other.
8050-200
1. Forward
2. Neutral
3. Neutral slot, Neutral lock
4. Reverse
Motion control lever, right side
8061-038
18
ContRoLs
Parking Brake
The parking brake is found on the right side of the The parking brake is found on the left of the machine. Pull the lever backward to activate the brake and forward to release it.
IMPORTANT INFORMATION
The machine must stand absolutely still when applying the parking brake. Always set the parking brake before dismounting. Release the parking brake before moving the mower.
Parking brake not activated
Throttle Control
The throttle control regulates the engine speed and thereby the rate of rotation of the blades, assuming the blade switch is pulled out, see Engaging the
Mower Deck.
In order to increase or decrease the engine speed, the control is moved forward or back respectively.
Avoid idling the engine for long periods, as there is a risk of fouling the spark plugs.
Use.FULL.tHRottLe.WHen.MoWInG, for best mower performance and battery charging.
Ignition Switch
The ignition key is placed on the control panel and is used to start and stop the engine.
IMPORTANT INFORMATION
Do not run the starter for more than five seconds each time. If the engine does not start, wait about 10 seconds before retrying.
Throttle control
Ignition switch
8061-010
8061-017
8061-017
19
ContRoLs
Choke Control
The choke control is used for cold starts in order to provide the engine with a richer fuel mixture.
For cold starts the control should be pushed to the
ON position.
WARNING!
Gasoline is highly flammable. Observe caution and fill the tank outdoors (see the safety instruction).
Choke control
Blade Switch
In order to engage the mower deck, pull the knob out; the mower blades are disengaged when the knob is depressed.
Fuses
Fuses are located on the left hand side of the machine. They are accessed by tilting the seat forward. They are flat pin fuses of the same type used in automobiles.
There are two fuses with ratings and functions:
• 20 A, Primary fuse.
• 7.5 A, Mower deck coupling.
Blade switch
Fuses
20
8061-017
8061-017
8011-420
ContRoLs
Seat Adjustment Lever
The seat can be adjusted lengthways. When making adjustments, the lever under the front edge of the seat is moved to the left (as seen by the driver in the seat), after which the seat can be moved backward or forward.
Hour Meter
The hour meter displays the total operating time.
It will flash CHG OIL (Change Oil) at 50 hour intervals.
The flash duration is one hour before and one hour after the interval. The CHG OIL icon will come on and shut off automatically. The hour meter cannot be manually reset.
Lengthways adjustment
IMPORTANT INFORMATION
In order to obtain an even cutting height, it is important that the air pressure in the front tires is 15 psi and the rear tires is 10 psi.
Cutting Height Adjuster
The deck cutting height is obtained by pressing the foot pedal forward to lift the deck. To lower the deck, apply pressure to the top side of the foot pedal and allow it to pivot while the lift arm rotates to the rear of the unit. To stop in the desired cutting position, rotate the foot pedal down into the notch in the height plate.
The cutting height range is from 1½" (38mm) to 4½"
(114mm) in ¼ (6mm) increments. The heights are measured from the ground up to the blade tip with the engine not running.
Hour meter
The mower deck’s lifting lever
8011-441
8061-017
8050-117
21
ContRoLs
Fuel Shut Off Valve
The fuel shut off valve is located in the fuel line under the seat. Tilt seat forward for access. The fuel valve is
ON when the valve is parallel to the fuel line. Rotate the valve ¼ turn clockwise to turn fuel OFF.
IMPORTANT INFORMATION
In order to obtain an even cutting height, it is important that the air pressure is 15 psi in all tires.
Tracking
If the mower is not tracking straight, check the air pressure in both rear tires. Recommended air pressure is 15 psi. (1 bar) Tracking must be checked on a flat and level concrete or blacktop surface. If the unit still does not track straight contact your Dixon workshop for adjustments.
•
•
•
WARNING!
No adjustments or maintenance to be carried out unless: the engine stopped the ignition key removed the parking brake activated
Fuel shut off valve in the OPEN position.
8050-010
22
ContRoLs
Fuel Tank
Read the safety instructions before refueling. The machine has one fuel tank, just behind the seat. The tank capacity is 5.7 gallons (22 liters).
Make sure the fuel cap is properly tightened and the cap gasket is not damaged.
The engine will run on a minimum of 85-octane unleaded gasoline (no oil mix). Environmentally adapted alkylate gasoline can be used. See also
Technical Data concerning ethanol fuel. Methanol fuel is not allowed. Do not use E85 alcohol based fuel.
Damage to engine and components may occur.
WARNING!
Gasoline is highly flammable.
Observe caution and fill the tank outdoors (see the safety instruction).
Fuel tank
WARNING!
The engine and the exhaust system, become very hot during operation.
Risk for burns if touched.
Allow engine and exhaust system to cool at least two (2) minutes before refueling
WARNING!
Fill to bottom of filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.
When operating in temperatures below 32° F. (0° C.), use fresh, clean winter grade gasoline to help insure good cold weather starting.
8061-221
IMPORTANT INFORMATION
Experience indicates that alcohol blended fuels (called gasohol, ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel the next season. See Storage Instructions for additional information. Never use engine or carburetor cleaners in the fuel tank or permanent damage may occur.
23
oPeRAtIon
Read the Safety section and following pages, if you are unfamiliar with the machine.
Training
Zero turn mowers are far more maneuverable than typical riding mowers due to their unique steering capabilities.
We suggest that this section be reviewed in its entirety prior to attempting to move the mower under its own power. Additionally, we suggest when first operating the mower, use a reduced throttle speed and reduced ground speed by NOT moving control levers to the furthest forward or reverse positions during initial operation, or until operator becomes comfortable with controls. We also suggest first time users, or new users to Zero Turn mowers to become familiar with the mower’s movement on a hard surface, such as concrete or blacktop PRIOR to attempting to operate on turf. Until operator becomes comfortable with mower controls and zero turning capability, they may damage turf due to overly aggressive maneuvers.
IMPORTANT INFORMATION
When control levers are in the reverse position they return to neutral when released. This may cause the mower to suddenly stop.
Steering
To move forward and backward
The direction and speed of the mower’s movements is effected by the movement of the control lever(s) on each side of mower. The left control lever controls the left wheel. The right control lever controls the right wheel.
First time users should push mower (see Manual
Transport in the Operation section) to an open, flat area, without other people or vehicles/obstacles nearby. In order to move unit under its own power, the operator must be in the seat, start engine (see
Before Starting in Operation section), adjust engine speed to idle, disengage parking brake, do not engage blades at this time, rotate control levers inward. As long as the control levers have not been moved forward or backwards, mower will not move.
Slowly move both control levers forward slightly. This will allow mower to start moving forward in a straight line. Pull back on control levers to the neutral position and mower should stop moving. Pull back slightly on control levers, this will allow mower to start moving backwards. Push forward on control levers to the neutral position and mower should stop moving.
To turn to the right
While moving in a forward direction, pull the right lever back towards the neutral position while maintaining the position of the left lever, this will slow the rotation of the right wheel and cause the machine to turn in that direction.
To turn to the left
While moving in a forward direction pull the left lever back towards the neutral position while maintaining the position of the right lever, this will slow the rotation of the left wheel and cause the machine to turn in that direction.
To zero turn
While moving in a forward direction, first pull both control levers back until the mower stops or slows dramatically.
Then by alternating one lever slightly to the forward position and the other in the reverse position.
24
oPeRAtIon
Before Starting
• Read the sections Safety Instructions and
Controls before starting the machine.
•
•
•
Perform the daily maintenance before starting
(see Maintenance Schedule in the Maintenance section).
Check that there is sufficient fuel in the fuel tank.
Adjust the seat to the desired position.
The following conditions must be fulfilled before the engine can be started:
•
•
•
•
The driver must be seated on the seat.
The blade switch for engaging the mower blades must be depressed.
The parking brake must be on.
Both steering controls must be in the locked
(outer) neutral position.
Starting the Engine
1.
2.
3.
Sit on the seat.
Raise the mower deck by pulling the lifting lever backward to the locked position (transport position).
Activate the parking brake.
The mower deck’s lifting lever
8050-117
8061-010
Disengage the mower blades by pressing the blade switch downwards.
Activate parking brake
Blade switch
8061-017
25
oPeRAtIon
Move the steering controls outward to the locked
(outer) neutral position.
8061-021
Move the throttle to the middle position.
WARNING!
Engine exhaust and certain vehicle components contain or emit chemicals considered to cause cancer, birth defects or other reproductive system damage. The engine exhaust contains carbon monoxide, which is a odorless, colorless, poisonous gas. Do not use the machine in enclosed spaces.
Place controls in neutral position
Set the throttle
If the engine is cold, the choke lever should be pushed to the ON position.
8061-017
Set the choke control
8061-017
26
Open the fuel valve.
oPeRAtIon
Press in and turn the ignition key to the start position
Open the fuel valve
8050-010
Turn to START position
When the engine starts, immediately release the ignition key back to the run position.
IMPORTANT INFORMATION
Do not run the starter for more than 5 seconds each time. If the engine does not start, wait approximately 10 seconds before retrying.
Slowly slide the choke control back to the OFF position when the engine has started.
Set the desired engine speed with the throttle. Allow the engine to run at a moderate speed, “half throttle” for 3-5 minutes before loading it to heavily. USE FULL
THROTTLE WHEN MOWING (no choke).
Release ignition to the RUN position
8050-135
8050-136
27
oPeRAtIon
Weak Battery
WARNING!
Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.
IMPORTANT INFORMATION
Your mower is equipped with a 12-volt negative grounded system. The other vehicle must also be a 12-volt negative grounded system. Do not use your mower to start other vehicles.
If your battery is too weak to start the engine, it should be recharged. (See Battery in the Maintenance section.)
If jumper cables are used for emergency starting, follow this procedure:
Jumper cables
1. Connect each end of the RED cable to the
POSITIVE (+) terminal on each battery, taking care not to short against chassis.
2.
3.
Connect one end of the BLACK cable to the
NEGATIVE (-) terminal of the fully charged battery.
Connect the other end of the BLACK cable to a good CHASSIS GROUND on the mower with the discharged battery, away from the fuel tank and battery.
To remove cables, reverse order
1. Remove BLACK cable first from chassis and then from the fully charged battery.
2. Remove RED cable last from both batteries.
Jumper cable connection
8011-642
28
oPeRAtIon
Running
1.
2.
Release the parking brake by moving the lever downward.
NOTE: The mower is equipped with an operator presence system. When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine.
Move the steering controls to the neutral position
(N).
8061-010
3.
4.
5.
Select the cutting height with the cutting height adjustment pedal.
Make sure the work area is free from objects that could be thrown by the rotating blades.
Engage the mower deck by pulling out the blade switch.
Released parking brake
WARNING!
Ensure that no one is near mower when engaging blade control lever.
The mower deck’s lifting lever
6.
7.
Move throttle control to full throttle.
The machine’s speed and direction are continuously variable using the two steering controls. When both controls are in the neutral position, the machine stands still.
By moving both controls an equal amount forward or backward, the machine moves in a straight line forward or backward respectively.
In order, for example, to turn right while moving forward, move the right control towards the neutral position. The rotation of the right wheel is reduced and the machine turns to the right.
Turning on the spot (zero turn) can be achieved by moving one control backward (behind the neutral position) and carefully moving the other steering control forward from its neutral position.
Set blade engagement and throttle control
8050-117
8061-017
29
oPeRAtIon
Operating On Hills
Read the Safety Instructions “Driving on Slopes” in the
“Safety Instructions”.
WARNING!
Do not drive up or down hills with slopes greater than 10 degrees. Do not drive across slopes.
•
•
•
The slowest speed possible should be used before starting up or down hills.
Avoid stopping or changing speed on hills.
If stopping is absolutely necessary, pull drive levers into the neutral position and push to the outside of the unit and engage the parking brake.
IMPORTANT INFORMATION
When in reverse, control levers return to neutral when released. This may cause the mower to suddenly stop.
•
•
•
To restart movement, release the parking brake.
Pull the control levers back to the center of the mower and press forward to regain forward motion.
Make all turns slowly.
Place controls in neutral position
Released parking brake
8061-020
8061-010
30
oPeRAtIon
Mowing Tips
•
•
•
•
Observe and flag rocks and other fixed objects to avoid collisions.
Begin with a high cutting height and reduce it until the desired mowing result is attained.
The average lawn should be cut to
2½" (64 mm) during the cool season and over 3"
(76 mm) during the hot months. For healthier and better looking lawns, mow often after moderate growth.
For best cutting performance, grass over 6" (15 cm) in height should be mowed twice. Make the first cut relatively high, the second to the desired height.
The mowing result will be best with a high engine speed (the blades rotate rapidly) and low speed
(the rider moves slowly). If the grass is not too long and dense, the driving speed can be increased without negatively affecting the mowing result.
The finest lawns are obtained by mowing often.
The lawn becomes more even and the grass clippings more evenly distributed over the mown area. The total time taken is not increased as a higher operating speed can be used without poor mowing results.
•
•
•
•
Avoid mowing wet lawns. The mowing result is poorer because the wheels sink into the soft lawn, clumps build, and the grass clippings fasten under the cowling.
Hose the mower deck underside with water after each use. When cleaning, the mower deck shall be raised into the transport position. Make sure the mower is cooled and the engine is off.
Use compressed air to clean top surface of the deck. Avoid flooding water on top surface, engine and electrical components.
When the mulching kit is used, it is important that the mowing interval is frequent.
Mowing pattern
WARNING!
Clear the lawn of stones and other objects that can be thrown out by the blades.
8011-603
WARNING!
Never drive the rider on terrain that slopes more than 10 degrees. Mow slopes up and down, never side to side.
Avoid sudden directional changes.
31
oPeRAtIon
Stopping the Engine
Allow the engine to idle a minute in order to attain normal operating temperature before stopping it, if it has been worked hard. Avoid idling the engine for longer periods, as there is a risk of the spark plugs fouling.
• Disengage the mower deck by despressing the blade switch.
•
•
•
Raise the mower deck by pressing the foot pedal forward to the transport position.
When the machine is standing still, activate the parking brake by pulling the lever upward.
Move the throttle to the minimum position (tortoise symbol). Turn the ignition key to the stop position.
Set blade engagement and throttle control
8061-017
8050-117
•
•
Move the steering controls outward.
Remove key. Always remove key when leaving the mower to prevent unauthorized use.
IMPORTANT INFORMATION
Leaving the ignition switch in any other position than “OFF” will cause the battery to be discharged.
The mower deck’s lifting lever
Place controls in neutral position
32
8061-020
oPeRAtIon
Manual Transport
IMPORTANT INFORMATION
Tighten the valve moderately.
Do not overtighten the valve when closing.
That can damage the valve seat.
Pump Release Valves
Pump release valves are located at the front and rear of the pump. They are used to release the system so the machine may be moved by hand when not running. Tilt seat forward to gain access to the pump.
The rear bypass valve sits directly opposite the front valve, below the seat support. It is not visible in the illustration.
Use a 17 mm open end wrench or socket and ratchet.
Turn the outer locknut 2-3 turns. Using an 8mm wrench or socket, turn the inner nut one turn.
Reverse the procedure to reset the pump.
Pump release valve
8061-006
33
MAIntenAnCe
Maintenance Schedule
The following is a list of maintenance procedures that must be performed on the machine. For those points not described in this manual, visit an authorized service workshop. An annual service carried out by an authorized service workshop is recommended to maintain your machine in the best possible condition and to ensure safe operation.
Read Maintenance in the Safety section.
Maintenance
Check the parking brake
Check the engine’s oil level (every refueling)
Check the safety system
Check for fuel and oil leakages
Check/clean the engine’s cooling air intake
Check the mower deck
Check for loose hardware (screws, nuts)
Clean under the mower deck
Start the engine and blades, listen for unusual sounds
Check for damage
Thoroughly clean around the engine
Clean around belts, belt pulleys
Check the tire pressures
Check battery
Sharpen/replace mower blades
Clean the engine’s cooling air intake 2)
Clean the air cleaner’s pre-filter 2) (foam)
Clean the air cleaner’s filter cartridge 2) (paper filter)
Check/adjust the parking brake
Daily
Before After
Weekly At least once each year
Maintenance interval in hours
25 50 100 300
●
■
●
♦
■
●
♦
●
●
♦
♦
♦
●
■ ■
●
●
■ ■
■
♦
■
♦
1) First change after 5-8 hours. When operating with a heavy load or at high ambient temperatures, replace
2) every 50 hours.
In dusty conditions, cleaning and replacement are required more often.
3) For daily use, the machine should be lubricated twice weekly.
4) Performed by authorized service workshop.
●
= Described in this manual
♦
= Not described in this manual
■
= See engine manufacturers’ Owners Manual
34
Maintenance
Check/adjust throttle cable
Check the condition of belts, belt pulleys
Change the engine oil 1)
Replace the engine oil filter
Clean/replace the spark plugs
Check the caster wheels (every 200 hours)
Check/adjust the mower deck
Check the engine valve clearance 4)
Perform the 300-hour service 4)
Lubricate according to Lubrication Schedule 3, 4)
MAIntenAnCe
Daily
Before After
Weekly At least once each year
Maintenance interval in hours
25 50 100 300
●
■ ■
●
●
■
■
■
■
●
●
♦
♦ ♦
● ● ● ● ●
●
♦
1) First change after 5-8 hours. When operating with a heavy load or at high ambient temperatures, replace
2) every 50 hours.
In dusty conditions, cleaning and replacement are required more often.
3) For daily use, the machine should be lubricated twice weekly.
4) Performed by authorized service workshop.
●
= Described in this manual
♦
= Not described in this manual
■
= See engine manufacturers’ Owners Manual
WARNING!
•
•
•
•
•
Before performing any service or adjustment checklist:
Engage the parking brake.
Place the Blade-switch in the disengaged position.
Turn the ignition switch to “OFF” position and remove the key.
Make sure the blades and all moving parts have completely stopped.
Disconnect the spark plug wire from all spark plugs and place the wire where it cannot come in contact with the plug.
35
MAIntenAnCe
Battery
Your mower is equipped with a maintenance free battery that does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life.
•
•
•
Keep battery and terminals clean.
Keep battery bolts tight.
Recharge at 6-10 amperes for 1 hour
To clean battery and terminals
Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.
1.
2.
3.
4.
5.
Open the terminal access doors.
Remove the red terminal guard.
Disconnect BLACK battery cable first, then the
RED battery cable and remove the battery from the machine.
Rinse the battery with plain water and dry.
6.
7.
Clean terminals and battery cable ends with wire brush until shiny.
Coat terminals with grease or petroleum jelly
Reinstall battery.
Always use protective glasses when handling the battery.
STANDARD
BATTERY
12.6V
12.4V
12.2V
12.0V
11.8V
STATE
OF
CHARGE
100%
75%
50%
25%
APPROXIMATE BATTERY CHARGING TIME*
TO FULL CHARGE AT 80 O F / 27 O C
50 Amps
Maximum Rate at:
30 Amps 20 Amps 10 Amps
- FULL CHARGE -
20 min.
45 min.
65 min.
35 min.
75 min.
115 min.
48 min.
95 min.
145 min.
0% 85 min.
150 min.
195 min.
*Charging time depends on battery capacity, condition, age, temperature and efficiency of charger
90 min.
180 min.
280 min.
370 min.
IMPORTANT INFORMATION
Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.
Always use two wrenches for the terminal screws.
WARNING!
Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.
Positive terminal must be connected first to prevent sparks from accidental grounding.
Replacing battery
1. Lift seat and rotate forward.
2.
3.
4.
5.
6.
Open terminal access doors
Using two ½" wrenches disconnect BLACK battery cable then RED battery cable.
Using a 7 /
16
wrench, remove the bolts on either side of the terminal guard and lift off guard
Carefully remove the battery from the mower.
7.
8.
9.
Install new battery with terminals in the same position as the old battery.
Reinstall battery terminal guard.
Reconnect RED battery cable to positive (+) battery terminal with bolt and hex nut.
Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and hex nut.
10. Close access doors.
11. Lower seat.
36
2
1. Terminal guard
2. Access doors
Battery cleaning and installation
2
1
CZ-22
MAIntenAnCe
Safety System
The machine is equipped with a safety system that prevents starting or driving under the following conditions.
The engine can only be started when:
1. The mower deck is disengaged.
2. The steering controls are in the outer, locked neutral position.
3. The driver is sitting in the driver’s seat.
4. The parking brake is on.
Make daily inspections to ensure that the safety system works by attempting to start the engine when one of the conditions is not met. Change the conditions and try again.
If the machine starts when one of these conditions is not met, turn the machine off and repair the safety system before using the machine again.
Make sure the engine stops when the park brake is not engaged and the operator leaves the seated position.
Check that the engine stops if the mower blades are engaged and the driver temporarily moves off the drivers seat.
Start conditions
8050-913
IMPORTANT INFORMATION
In order to be able to drive, the driver must sit in the seat and release the parking brake before the steering controls can be moved into the neutral position, otherwise the engine will stop.
Tire Pressures
All tires should be at 15 psi / 103 kPa / 1 bar.
Parking Brake
Visually check that no damage is found on the lever, links, or switch belonging to the parking brake.
Perform a standstill test and check that there is sufficient braking action.
To adjust the parking brake, contact the Dixon service workshop.
WARNING!
Faulty adjustment can result in reduced braking ability and can cause an accident.
Check for proper operation of parking brake
8061-010
37
MAIntenAnCe
V-belts
Check every 100 hours of operation. Check for severe cracking and large nicks.
NOTE: The belt will show some small cracks in normal operation.
The belts are not adjustable. Replace belts if they begin to slip from wear.
Deck Belt
1. Park on a level surface. Apply parking brake.
2. Lower the deck into the lowest cutting position.
3.
4.
5.
Remove bolts from belt shields and remove shields.
Remove any dirt or grass that may have accumulated around the cutter housings and entire deck surface.
Carefully roll the belt over the top of the cutter housing pulleys and remove belt.
Remove belt shields
Deck Belt Installation
1.
NOTE: For ease in installing the deck belt, refer to the routing decal on bottom of seat.
Wrap the deck belt around the electric clutch pulley that is located on the engine shaft.
2.
3.
4.
5.
Route the belt forward between the EZT (E-Series
Zeroturn Transaxles) and up onto the deck.
Place belt around spring loaded idler pulley.
Wrap the belt around the stationary idler pulley and around the mandrel housings.
Push inward on the idler arm and carefully route belt over stationary idler pulley. Once belt is properly routed, slowly release idler arm to tension belt.
6.
7.
8.
Double check belt routing to make sure it matches the routing decal, and the belt does not have any twist. Correct as needed.
Adjust tension with deck eyebolt.
Replace belt shields on both mandrel housings and secure with fasteners.
Belt routing, deck belt
8050-842
8050-843
38
MAIntenAnCe
Pump Belt
Replacing Pump Belt
Park the mower on a level surface. Engage the parking brake.
Belt removal
1. Remove the deck belt (see Deck Belt Removal in this section of the manual).
2.
3.
Remove clutch stop to access the belt.
Disconnect clutch wire.
4.
5.
Create slack in the belt by removing the spring on the pump idler arm.
The belt should now be able to be removed from the engine pulley and pump pulleys.
Belt installation
1. Wrap the belt around the pulley
2.
3.
4.
5.
Route the belt around the inside of the idler pulley.
Wrap the belt around the engine pulley.
Reattach the spring on the pump idler arm.
Reconnect clutch wire.
6.
7.
Replace and secure clutch stop.
Reinstall the deck belt. (see Deck Belt Removal in this section of the manual).
1.
2.
3.
Electric clutch
Idler spring
Clutch stop
Pump belt removal
3
1
2
8054-003
Cutting Blades
In order to attain the best mowing effect, it is important that the blades are well sharpened and not damaged.
WARNING!
Blades are sharp. Protect your hands with gloves and/or wrap blades with a heavy cloth when handling.
IMPORTANT INFORMATION
The sharpening of blades should be carried out by an authorized service workshop.
Bent or cracked blades or blades with large nicks should be replaced.
Damaged blades should be replaced when hitting obstacles that result in a breakdown. Let the service workshop decide whether the blade can be repaired/ ground or must be replaced.
Balance the blades after sharpening.
Check the blade mounts.
39
MAIntenAnCe
Blade Replacement
WARNING!
Blades are sharp. Protect your hands with gloves and/or wrap blades with a heavy cloth when handling.
1
2
1. Remove blade bolt by turning counterclockwise.
IMPORTANT INFORMATION
To ensure proper assembly, center hole in blade must align with star on cutter housing.
2.
3.
4.
Install new or resharpened blade with stamped
“GRASS SIDE” facing towards ground/grass
(down) or “THIS SIDE UP” facing deck and cutter housing.
nstall and tighten blade bolt securely.
Torque blade bolt to 45-55 ft/lbs (60-75 Nm).
1.
2.
3.
Blade
Blade bolt (special)
Cutter housing
Blade attachment
IMPORTANT INFORMATION
Special blade bolt is heat treated.
Replace with a Dixon bolt if required.
Do not use lower grade hardware than specified.
3
8050-844
40
MAIntenAnCe
Adjusting the Mower Deck
WARNING!
Before performing any service or adjustment checklist:
1. Engage the parking brake.
2. Place the Blade switch in the disengaged position.
3. Turn ignition switch to “OFF” position and remove the key.
4. Make sure the blades and all moving parts have completely stopped.
5. Disconnect the spark plug wire from all spark plugs and place the wire where it cannot come in contact with the plug.
Check the tire pressure before adjustment of the mower deck. See “Checking Tire Pressure” in
Maintenance section. Faulty mower deck adjustments will cause an uneven mowing result.
Leveling
Adjust the deck while the mower is on a level surface. Make sure the tires are inflated to the correct pressure. See “Technical Data” under Transmission.
If tires are under or over inflated, you cannot properly adjust your deck.
Four slots control the height and pitch of the mower deck. The deck should be adjusted slightly higher in the rear.
NOTE:To insure accuracy of leveling procedure, mower deck drive belt must be installed prior to leveling deck.
1. Wear heavy gloves. Turn each outer blade tip to align with the deck or in a side-to-side manner.
2. Measure from the floor surface up to the bottom of the blade tip on the discharge side of the mower deck. Retain this measurement. Move to the opposite side, check that measurement is the same. If adjustment is required, loosen the locknut and move mounting bolt up or down in slot until both side-to-side measurements are equal. Retain measurement.
3. Turn both outer blades to align with the deck in front-to-rear manner. Reposition rear mounting bolts up or down until rear of mower deck is positioned level to 1 /
8
" higher in the rear than the side-to-side measurement.
NOTE: This will place the mower deck in a base measurement position. Additional adjustment may be required to achieve desired cut for the type of grass or conditions being mowed.
3
WARNING!
Blades are sharp. Protect your hands with gloves and/or wrap blades with a heavy cloth when handling.
1.
2.
3.
4.
Front lift arm
Chain
Rear lift arm
Slotted deck hanger plates
Leveling the mower deck
4
2
1
8050-914
41
MAIntenAnCe
Anti-Scalp Rollers
Anti-scalp rollers are properly adjusted when they are just slightly off of the ground when the deck is at the desired cutting height in the operating position.
Anti-scalp rollers then keep the deck in the proper position to help prevent scalping in most terrain conditions.
IMPORTANT INFORMATION
Adjust anti-scalp rollers with the mower on a flat level surface.
The anti-scalp rollers can be set in three positions:
• Upper position 1½ to 3" (38 to 76 mm) grass.
• Middle position 3" to 4½" (76 to 114 mm) grass.
• Lower position 4½" to 6" (114 to 152 mm) grass.
The rollers should be approximately ¼" (6.5 mm) from ground. Do not adjust the rollers to support the deck.
Anti-scalp rollers
IMPORTANT INFORMATION
The anti-scalp rollers must not be used for gauge wheels or the roller and deck may be damaged.
8058-054
42
MAIntenAnCe
Caster Wheels
Check every 200 hours. Check that wheels rotate freely. If wheels do not rotate freely take the unit to your dealer for service.
Foam filled tires or solid tires will void the warranty.
Removal and installation of caster wheel
1. Remove nut (1) and caster bolt (2).
2.
3.
Pull the wheel out of the fork and take care of the sleeve (3).
Reinstall in reverse order. Tighten caster bolt.
2
IMPORTANT INFORMATION
DO NOT add any type of tire liner or foam fill material to the tires. Excessive loads created by foam filled tires will cause premature failures.
Only use O.E.M. specified tires.
Cleaning
Regular cleaning and washing, especially under the mower deck, will increase the machine’s life-span.
Make it a habit to clean the machine directly after use
(after it is cooled), before the dirt sticks.
Do not spray water on the top of the mower deck. Use compressed air to clean the top side of mower deck.
Regularly clean deck and underside of the deck with normal water pressure. Do not use a high pressure washer or steam cleaner. Avoid spraying engine and electrical components with water
Do not rinse hot surfaces with cold water. Let unit cool before washing.
Use protective glasses when cleaning and washing.
Caster wheels
1
3
8011-619-1
Hardware
Check daily. Inspect the entire machine for loose or missing hardware.
43
LUBRICAtIon
8011-672-6
12/12.every.year
1/52.every.Week
1/365.every.day
*Change transaxles (transmission) filters.
Lubricate.with.grease.gun
oil.change
Filter.change
Lubricate.with.oil.can
Level.check
General
Remove the ignition key to prevent unintentional movements during lubrication.
When lubricating with an oil can, it must be filled with engine oil.
When lubricating with grease, unless otherwise stated, use a high grade molybdenum disulphide grease.
For daily use, the machine should be lubricated twice weekly.
Wipe away excess grease after lubrication.
It is important to avoid getting lubricant on the belts or the drive surfaces on the belt pulleys. Should this happen, attempt to clean them with spirits. If the belt continues to slip after cleaning, it must be replaced.
Gasoline or other petroleum products must not be used to clean belts.
44
LUBRICAtIon
Front Wheel Mount
Lubricate with a grease gun, one zerk for each wheel mount, until the grease is forced out.
Use only good quality bearing grease.
Grease from well-known brand names (petrochemical companies, etc.) usually maintains a good quality.
Front Wheel Bearings
Lubricate with a grease gun, one zerk for each set of wheel bearings, until the grease is forced out.
Use only good quality bearing grease.
IMPORTANT INFORMATION
Use minimal lubrication and remove excess lubricant so that is does not come into contact with belts or belt pulley drive surfaces.
Lubricating the wheel bearings
Deck Spindle
Lower the cutting deck completely.
If you use grease gun without rubber hose, the foot plate must be removed.
Lubricate with a grease gun, one zerk,
2-3 strokes.
Use only good quality bearing grease.
Engine Lubrication
Refer to the engine manufacturer's manual for maintenance and service instructions.
Deck spindle
8050-009
8011-732
45
LUBRICAtIon
Hydraulic Pump
Fluid Change
This transaxle is designed with an external filter for ease of maintenance. To ensure constant fluid quality levels and longer life an oil filter change interval of every 200 hours is recommended.
The following procedure can be performed with the pump installed in the vehicle, and the vehicle on level ground. Apply the bypass valve and lock the vehicle parking brake.
1.
2.
3.
4.
Place an oil drain pan with a two gallon capacity beneath the oil filter. Remove the oil filter from the pump.
After the oil has drained, wipe the filter base surface off and apply a film of new oil to the gasket of the new replacement filter.
Install the new filter by hand, turn ¾ to one full turn after the filter gasket contacts the filter base surface.
Drain old oil filters of all free-flowing oil prior to disposal. Place used oil in appropriate containers and dispose of it in accordance with laws in your area.
5.
6.
7.
8.
Remove the cap from the pump’s expansion tank located on the vehicle frame.
Fill reservoir with SAE 10W30 oil to just above the MIN-ADD line on the reservoir. After purging, check levels and add oil if necessary.
Reinstall the tank cap by hand. Do not overtighten.
Proceed to the purge procedure.
Purging
Due to the effects air has on efficiency in hydrostatic drive applications, it is critical that it is purged from the system.
These purge procedures should be implemented any time a hydrostatic system has been opened to facilitate maintenance or any additional oil has been added to the system.
The resulting symptoms in hydrostatic systems may be:
1. Noisy operation.
2.
3.
Lack of power or drive after short term operation.
High operation temperature and excessive expansion of oil.
2
3
1.
2.
3.
Pump filter
Pump reservoir
Fluid fill lines
Changing the hydraulic pump oil filter
1
8061-016
Before starting, make sure the pump is at the proper oil level. If it is not, fill to the specifications outlined earlier.
The following procedures are best performed with the vehicle drive wheels off the ground, then repeated under normal operating conditions.
1.
2.
Disengage the brake if activated.
With the bypass valve open and the engine running at fast idle, slowly move the directional control in both forward and reverse directions (5 or
6 times). As air is purged from the unit, the oil level will drop.
3.
4.
5.
With the bypass valve closed and the engine running, slowly move the directional control in both forward and reverse directions (5 to 6 times).
Check the oil level, and add oil as required after stopping the engine.
It may be necessary to repeat Steps 2 and 3 until all the air is completely purged from the system.
When the transaxle operates at normal noise levels and moves smoothly forward and reverse at normal speeds, then the transaxle is considered purged.
After the vehicle has been used two times, the oil level should be checked while the oil is cold and adjusted accordingly.
46
Problem
The engine will not start.
The engine runs rough.
tRoUBLesHootInG
Cause
•
•
•
•
•
•
•
•
Blade lever is engaged.
Steering controls are not locked in neutral position.
Driver is not sitting in driver’s seat.
Parking brake is not activated.
Battery is dead.
Contamination in carburetor or fuel line.
Fuel supply is closed or tap for fuel tank is in wrong position.
Clogged fuel filter or fuel line.
The starter does not turn the engine over.
•
•
•
•
•
Dead battery.
Poor contacts on the battery terminal cable connections.
Fuse blown.
Ignition system faulty.
Fault in the starter safety circuit. See Checking the
Safety System in the Maintenance section.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Faulty carburetor.
Choke control used with warm engine.
Defective valves.
Defective piston, cylinder, piston ring, or cylinder head seal.
Cylinder head bolts are loose.
Clogged fuel filter or jet.
Clogged ventilation valve on fuel cap.
Fuel tank nearly empty.
Fouled spark plug.
Spark plug is loose.
Defective ignition cable.
Defective spark plug electrode.
Defective spark plug connection.
Rich fuel mixture or fuel-air mixture.
Wrong fuel type.
Water in fuel.
Clogged air filter.
47
Problem
The engine seems weak.
The engine overheats.
Battery not charging.
Mower deck not engaging.
Uneven mowing results.
The machine vibrates.
tRoUBLesHootInG
The machine moves slowly, unevenly, or not at all.
Cause
•
•
•
•
•
•
•
•
•
•
•
Clogged air filter.
Fouled spark plugs.
Carburetor incorrectly adjusted.
Clogged air intake or cooling fins.
Engine overloaded.
Poor ventilation around engine.
Defective engine speed regulator.
Soot in the combustion chamber.
Too little or no oil in the engine.
Fouled spark plug.
Poor contact with battery terminal cable connectors.
•
•
•
•
•
•
•
•
•
Parking brake on.
Hydraulic pump bypass linkage engaged.
Drive belt for the transmission gears slack or has come off.
Defective hydraulic system.
Air in hydraulic system.
Drive belt for the mower deck has come loose.
Contact for the electromagnetic coupling has loosened.
Blade switch is faulty or has come loose, from the cable contact.
Fuse has blown.
•
•
•
•
•
•
•
Different air pressure in the tires on left and right sides.
Bent blades.
Suspension for the mower deck is uneven.
Blades are dull.
Driving speed too high.
Grass is too long.
Grass collected under the mower deck.
•
•
•
Blades are loose.
Blades are incorrectly balanced.
Engine is loose.
48
stoRAGe
Winter Storage
At the end of the mowing season, the machine should be readied for storage (or if it will not be in use for longer than 30 days). Fuel allowed to stand for long periods of time (30 days or more) can leave sticky residues that can plug the carburetor and disrupt engine function.
Fuel stabilizers are an acceptable option as regards to the sticky residues that can occur during storage.
Add stabilizer to the fuel in the tank or in the storage container. Always use the mixing ratios specified by the manufacturer of the stabilizer. Run the engine for at least 10 minutes after adding the stabilizer so that it reaches the carburetor. Do not empty the fuel tank and the carburetor if you have added stabilizer
WARNING!
Never store an engine with fuel in the tank indoors or in poorly ventilated spaces where fuel vapor can come in contact with open flames, sparks, or a pilot light such as in a boiler, hot water tank, clothes drier, etc. Handle the fuel with care. It is very flammable and can cause serious personal injury and property damage. Drain the fuel into an approved container outdoors and far away from open flame. Never use gasoline for cleaning. Use a degreaser and warm water instead.
To ready the machine for storage, follow these steps:
1.
2.
3.
4.
Thoroughly clean the machine, especially under the mower deck. Touch up damage to the paint and spray a thin layer of oil on the underside of the mower deck to avoid corrosion.
Inspect the machine for worn or damaged parts and tighten any nuts or screws that may have become loose.
Change the engine oil; dispose of properly.
Empty the fuel tanks or add a fuel stabilizer. Start the engine and allow it to run until the carburetor is drained of fuel or the stabilizer has reached the carburetor.
5.
6.
7.
8.
Remove the spark plug and pour about a tablespoon of engine oil into the cylinder. Turn over the engine so that the oil is evenly distributed and then refit the spark plug.
Lubricate all grease zerks, joints, and axles.
Remove the battery. Clean, charge, and store the battery in a cool place, but protect it from direct cold.
Store the machine in a clean, dry place and cover it for extra protection.
Service
When ordering spare parts, please specify the purchase year, model, type, and serial number.
Always use genuine Dixon spare parts.
An annual checkup at an authorized service workshop is a good way to ensure that the machine performs its best the following season.
49
sCHeMAtIC
50
8053-002
Engine crankshaft bolt
Deck pulley bolts
Lug nuts
Blade bolt
Standard ¼" fasteners teCHnICAL.DAtA
Torque Specifications
50 ft/lb (67 Nm)
150 ft/lb (203 Nm)
75 ft/lb (100 Nm)
90 ft/lb (122 Nm)
9 ft/lb (12 Nm)
Standard 5 /
16
" fasteners
Standard 3 /
8
" fasteners
Standard 7 /
16
" fasteners
Standard ½” fasteners
18 ft/lb (25 Nm)
33 ft/lb (44 Nm)
52 ft/lb (70 Nm)
80 ft/lb (110 Nm)
M12
M14
M16
M18
M20
M22
M24
M27 ft./lbs
M4
M5
M6
M7
M8
M10
HEX HEAD CAP SCREWS
The torque values shown should be used as a general guideline when specific torque values are not given.
Grade
U.S. Standard Hardware
SAE Grade 5 SAE Grade 8 Flangelock Screw w/Flangelock Nut ft./lbs Nm ft./lbs
5
¼
/
16
3 /
8
7 /
16
½ ft./lbs
9
18
31
50
75
Nm
12
24
42
68
102 ft./lbs
13
28
46
75
115
9
5
/
16
/
8
¾
110
150
250
150
203
339
165
225
370
224
305
502
1
7
1
/
8
/
8
378
782
513
1060
591
1410
** Grade 5 - Minimum commercial quality (lower quality not recommended)
801
1912
Nm
18
38
62
108
156
24
40
33
54
Grade Grade 8.8
Metric Standard Hardware
Grade 10.9
Grade 12.9
43.5
70.5
108
142
195
276
353
530 ft./lbs
1.5
3
5.2
8.2
13.5
24
58
94
144
190
260
368
470
707
11
18
32
Nm
2
4
7
62.2
100
147
202
275
390
498
474 ft./lbs
2.2
4.5
7.5
12
18.8
35.2
83
133
196
269
366
520
664
996
16
25
47
Nm
3
6
10
75
119
176
242
330
471
596
904 ft./lbs
2.7
5.2
8.2
15
21.8
43.5
100
159
235
323
440
628
794
1205
20
29
58
Nm
3.6
7
11
51
teCHnICAL.DAtA
966985401, 966985402
Engine
Manufacturer
Type
Power
Lubrication
Oil capacity excluding filter
Oil capacity including filter
Engine oil
Fuel
Fuel tank capacity
Spark plugs / gap
Kohler
Courage
25 hp*
Pressure with oil filter
1.6 qts/ 1.5 liters
1.7 qts / 1.6 liters
SAE 10W30, 10W40, 5W20,
5W30, API SF-SJ
Min 87 octane unleaded (Max ethanol 10%, Max MTBE 15%)
5.2 gallons / 19.7 liters
Champion RCY12YC
.030" / 0.75 mm
Air cooled
Standard
12V / 16A
Electric 12V
Cooling
Air filter
Alternator
Starter
Transmission
Transmission
Speed and direction controls
Speed forward
Speed reverse
Brakes
Front caster tires, smooth tread
Rear tires, turf pneumatic
Tire pressure
Hydraulic pump
Dual levers, foam gripped
0-8 mph / 0-12.9 km/h
0-4 mph / 0-6.4 km/h
Mechanical parking brake
13 x 6.5-6, 4 ply
23 x 10.5-12
15 PSI / 103 kPa / 1 bar
*The power rating of the engines indicated is the average net power output (at specified rpm) of a typical production engine for the engine model measured to SAE standard
J1349/ISO1585. Mass production engines may differ from this value. Actual power output for the engine installed in the final machine will depend on the operating speed, environmental conditions and other variables.
52
Equipment
Cutting width
Cutting height
Number of blades
Blade length
Nose Rollers
Sprung seat
Hinged armrests
Hour Meter
Blade engagement
Deck construction
Productivity
Output
Overall dimensions
Weight
Base machine length
Base machine width
Base machine height
Overall width, chute up
Overall width, chute down teCHnICAL.DAtA
966985401, 966985402
61" / 155cm
1½ - 4½" / 3.8 - 11.4 cm
3
21" / 43 cm
Yes
Standard
Yes
Standard
Electromagnetic clutch
11 gauge fabricated
4.8 acres /h 19425 m 2 /h
780 lbs / 354 kg
76" / 193 cm
72" / 183 cm
42" 107 cm
64" / 163 cm
78" / 198 cm
53
ConFoRMItY.CeRtIFICAtes
USA requirements
Labels are placed on the engine and/or in the engine compartment stating that the machine will fulfill the requirements. This is also applicable to special requirements for any of the states, (California emission rules etc.). Do not remove any of these labels.
Certificates can also be supplied with the machine at delivery or written in the Engine manual. Take care of them as they are valuable documents.
CE requirements
If required, vibration data corresponding to Directive
2002/44/EC is given in the Technical Data Section.
The Declaration of Conformity is included in the literature packet.
54
WARRAntY
DIXON
®
ZTR
®
COMMERCIAL / RESIDENTIAL
RAM 44, RAM 50, RAM 44 MAG™, RAM 50 MAG™
RAM ULTRA 50, RAM ULTRA 60 & RAM ULTRA 72
DIXON WARRANTS ITS ZTR® MOWERS AGAINST DEFECTS IN MATERIAL AND WORKMANSHIP FOR THE PERIODS SET FORTH BELOW. THE
SOLE REMEDY UNDER THIS WARRANTY IS REPLACEMENT OR REPAIR OF PARTS INCLUDING LABOR COSTS.
THIS WARRANTY IS SUBJECT TO THE FOLLOWING CONDITIONS AND LIMITATIONS:
1. COMMERCIAL WARRANTY (use other than, or in addition to, mowing at owner’s primary place of residence): a. One Year - 100% parts and labor subject to the conditions and limitations described herein for a period of one year from date of purchase by the original owner.
b. c. d.
Attachments marketed through or approved by Dixon are warranted for one year parts and labor in commercial use applications.
The RAM 44, RAM 50, RAM 44 MAG, RAM 50 MAG RAM ULTRA 50, RAM ULTRA 60 and RAM ULTRA 72 are not subject to hour meter restrictions.
Warranty applies to new mowers.
2. RESIDENTIAL WARRANTY (used only at owner’s primary place of residence): a. Two years - 100% parts and labor subject to the conditions and limitations described herein for a period of two years from date of purchase by the original owner.
b. c.
Third year - limited to 100% parts cost as shown in the current Dixon Parts Price List and subject to the conditions and limitations as described herein.
Attachments marketed through or approved by Dixon are warranted for two years parts and labor in residential use applications.
d. Warranty applies to new mowers.
3. All Dixon warranty must be accomplished by authorized Dixon dealers and in accordance with Dixon warranty policy and allowances. All warranty claims must be submitted to Dixon for approval.
4. Warranty labor reimbursement to dealers based on published Dixon flat rate schedule.
5. Warranty does not apply to damage in transit or incidents of misuse, negligence, accidents, or alteration. The use of parts or components other than those supplied by Dixon VOIDS ALL WARRANTY.
6. Battery warranty is limited to 1 year from mower manufacture date.
7. The following items are not covered by this warranty policy: a. Routine maintenance or adjustments to include any oils, filters or other fluids used.
b. c. d. e.
Belts, blades, tires and cosmetic appearance (paint, seat fade, etc.)
Pick up and delivery charges for transportation of mower to and from an authorized Dixon dealer’s place of business.
Engines. These are covered under a separate warranty by each individual engine manufacturer. Consult engine manual for warranty details.
Any costs or expense of providing substitute equipment while repair work is being performed on a warranted mower.
8. THERE IS NO OTHER EXPRESS WARRANTY. TO THE EXTENT PERMITTED BY LAW, ALL IMPLIED
WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE EXCLUDED, OTHERWISE, ALL SUCH IMPLIED WARRANTIES ARE LIMITED TO THE SAME DURATION
AND REMEDIES AS THE EXPRESS WARRANTY. ALL LIABILITIES FOR CONSEQUENTIAL DAMAGES UNDER
ANY EXPRESS OR IMPLIED WARRANTY ARE EXCLUDED.
55
seRVICe.JoURnAL
Action Date, mtr reading, stamp, sign
Delivery Service
1. Charge battery.
2. Adjust tire pressure of all wheels according to Technical Data.
3. Mount the steering controls in the normal position.
4. Connect the contact box to the cable for the seat’s safety switch.
5. Check that the right amount of oil is in the engine.
6. Adjust the position of the steering controls.
7. Fill with fuel and open the fuel shut off valve.
8. Start the engine.
9. Check that there is drive to both wheels.
10. Check the mower deck adjustment.
11. Check:
The safety switch for the parking brake.
The safety switch for the mower deck.
The safety switch in the seat.
The safety switch in the steering controls.
Parking brake functionality.
Driving forward.
Driving backward.
Engaging the blades.
12. Check the idle speed
13. Check the engine high idle speed
14. Inform the customer about:
The need and advantages of following the service schedule.
The need and advantages of leaving the machine for service every 300 hours.
The effects of service and maintaining a service journal on the machine’s resale value.
Application areas for Mulching.
15. Fill in the sales papers
Delivery service has been carried out.
No remaining notes.
Certified:
56
Action
After the First 10 Hours
1. Change engine oil.
seRVICe.JoURnAL
Date, mtr reading, stamp, sign
25-Hour Service
1. Check the fuel pump’s air filter.
2. Check the hydraulic system’s oil level.
3. Check the tire pressures.
4. Lubricate the belt adjuster, mower deck.
5. Lubricate the belt adjuster, hydraulic pumps.
6. Check/clean the engine’s cooling air intake.
7. Clean air filter dust cap.
57
seRVICe.JoURnAL
Action
50-Hour Service
1. Perform the 25-hour service.
2. Clean/replace the air cleaner’s filter cartridge (paper filter)
(shorter intervals for dusty operating conditions).
3. Change engine oil.
4. Lubricate according to lubrication chart.
5. Check/adjust the parking brake.
Date, mtr reading, stamp, sign
58
100-Hour Service
1. Perform the 25-hour service.
2. Perform the 50-hour service.
3. Change the engine oil filter.
4. Clean/replace the spark plugs.
5. Replace the fuel filter.
6. Clean the cooling fins on the engine and transmission.
7. Check V-belts.
8. Check/tighten caster wheel axle bolts (every 200 hours).
9. Change the air filter’s paper cartridge.
seRVICe.JoURnAL
Action
300-Hour Service
1. Perform the 25-hour service.
2. Perform the 50-hour service.
3. Perform the 100-hour service.
4. Check/adjust the mower deck.
5. Clean the combustion chamber and grind the valve seats.
6. Check the engine valve clearance.
7. Replace the air cleaner’s prefilter (foam).
Date, mtr reading, stamp, sign
At Least Once Each Year
1. Clean the engine’s cooling air intake (25 hours).
2. Replace the air cleaner’s pre-filter (foam) (300 hours).
3. Replace the air filter’s paper cartridge.
4. Change the engine oil (50 hours).
5. Replace the engine oil filter (100 hours).
6. Check/adjust the cutting height.
7. Check/adjust the parking brake (50 hours).
8. Clean/change the spark plugs (100 hours).
9. Change the fuel filter (100 hours).
10. Clean the cooling fins (100 hours).
11. Check the engine valve clearance.
59
Action seRVICe.JoURnAL
Date, mtr reading, stamp, sign
60
Action seRVICe.JoURnAL
Date, mtr reading, stamp, sign
61
Action seRVICe.JoURnAL
Date, mtr reading, stamp, sign
62
P/N 115 354727R1 01/06/10
ડાઉનલોડ કરો
જાહેર લિંક અપડેટ થઈ
તમારી ચેટની જાહેર લિંક અપડેટ કરવામાં આવી છે. You may view and manage your chat links after registration here.
દસ્તાવેજ જાહેર લિંક
જાહેરાત
