MiLAN | MIL-S8000T | User guide | MiLAN MIL-S8000T User guide

MiLAN MIL-S8000T User guide
MIL-S8000T
8-Port 1000BASE-T
Gigabit Ethernet Switch
USER GUIDE
Regulatory Approval
- FCC Class A
- UL 1950
- CSA C22.2 No. 950
- EN60950
- CE
- EN55022 Class A
- EN55024
Canadian EMI Notice
This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numerique de la classe A respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada.
European Notice
Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC)
issued by the Commission of the European Community Compliance with these directives imply conformity to the following
European Norms:
EN55022 (CISPR 22) - Radio Frequency Interference
EN61000-X - Electromagnetic Immunity
EN60950 (IEC950) - Product Safety
Five-Year Limited Warranty
MiLAN Technology warrants to the original consumer or purchaser that each of it's products,
and
all components thereof, will be free from defects in material and/or workmanship for a
period of five years from the original factory shipment date. Any warranty hereunder is
extended to the original consumer or purchaser and is not assignable.
MiLAN Technology makes no express or implied warranties including, but not limited to, any
implied warranty of merchantability or fitness for a particular purpose, except as expressly set
forth in this warranty. In no event shall MiLAN Technology be liable for incidental or
consequential damages, costs, or expenses arising out of or in connection with the
performance of the product delivered hereunder. MiLAN Technology will in no case cover
damages arising out of the product being used in a negligent fashion or manner.
Trademarks
The MiLAN logo and MiLAN Technology trademarks are registered trademarks of MiLAN Technology in the
United States and/or other countries.
To Contact MiLAN Technology
For prompt response when calling for service information, have the following information ready:
- Product serial number and revision
- Date of purchase
- Vendor or place of purchase
You can reach MiLAN Technology technical support at:
E-mail: support@milan.com
Telephone: +1.408.744.2751
Fax: +1.408.744.2771
MiLAN Technology
1329 Moffett Park Drive
Sunnyvale, CA 94089
United States of America
Telephone: +1.408.744.2775
Fax: +1.408.744.2793
http://www.milan.com
info@milan.com
© Copyright 2004
MiLAN Technology
P/N: 90000426 Rev. A
Table of Contents
1. Introduction
Gigabit Ethernet Technology
Switching Technology
Features
Package Contents
2. Hardware Description
Front Panel
Rear Panel
LED Indicators
3. Hardware Installation
Desktop Installation
Power On
4. Technical Specifications
General Specifications
Physical and Environmental Specifications
Performance Specifications
Appendix A: Regulatory Information
1.
Introduction
Gigabit Ethernet Technology
Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utilizing the same packet
structure, format, and support for CSMA/CD protocol, full duplex, flow control, and
management objects, but with a tenfold increase in theoretical throughput over
100-Mbps Fast Ethernet and a hundredfold increase over 10-Mbps Ethernet.
Since it is compatible with all 10-Mbps and 100-Mbps Ethernet environments,
Gigabit Ethernet provides a straightforward upgrade without wasting a company’s
existing investment in hardware, software, and trained personnel.
The increased speed and extra bandwidth offered by Gigabit Ethernet are
essential to coping with the network bottlenecks that frequently develop as
computers and their busses get faster and user applications generate more traffic.
Upgrading key components, such as your backbone and servers to Gigabit
Ethernet can greatly improve network response times, as well as significantly
speed up the traffic between your subnets.
Gigabit Ethernet supports video conferencing, complex imaging, and similar
data-intensive applications. Likewise, since data transfers occur 10 times faster
than Fast Ethernet, servers outfitted with Gigabit Ethernet NIC’s are able to
perform 10 times the number of operations in the same amount of time.
Switching Technology
Another key development pushing the limits of Ethernet technology is in the field
of switching technology. A switch bridges Ethernet packets at the MAC address
level of the Ethernet protocol transmitting among connected Ethernet or fast
Ethernet LAN segments.
Switching is a cost-effective way of increasing the total network capacity available
1
to users on a local area network. A switch increases capacity and decreases
network loading by making it possible for a local area network to be divided into
different segments which do not compete with each other for network transmission
capacity, giving a decreased load on each.
The switch acts as a high-speed selective bridge between the individual segments.
The switch automatically forwards traffic that needs to go from one segment to
another, without interfering with any other segments. This allows the total network
capacity to be multiplied, while still maintaining the same network cabling and
adapter cards.
Switching LAN technology is a marked improvement over the previous generation
of network bridges, which were characterized by higher latencies. Routers have
also been used to segment local area networks, but the cost of a router and the
setup and maintenance required make routers relatively impractical. Today’s
switches are an ideal solution to most kinds of local area network congestion
problems.
Features
The MIL-S8000T Gigabit Ethernet Switch was designed for easy installation and
high performance in an environment where traffic on the network and the number
of users increase continuously.
„
„
„
„
„
„
„
„
„
„
„
„
8 1000BASE-T Gigabit Ethernet ports
Auto-Negotiation for 10/100/1000Mbps and duplex mode
Auto-MDI/MDIX for each port
Full/Half duplex transfer mode for 10 and 100Mbps
Full duplex transfer mode for 1000Mbps
Full wire speed reception and transmission
Store-and-Forward switching method
Supports 8K absolute MAC addresses
Supports 256KBytes RAM for data buffering
Extensive front-panel diagnostic LEDs
IEEE 802.3x flow control for full-duplex
Back pressure flow control for half-duplex
2
Package Contents
Unpack the contents of the package and verify them against the checklist below.
„
„
„
„
„
MIL-S8000T Gigabit Ethernet Switch
External Power Adapter
Four Adhesive Rubber Feet
User's Guide
Warranty Card
If any item is missing or damaged, please contact your local dealer for service.
3
2.
Hardware Description
Front Panel
The front panel of the Gigabit Ethernet Switch consists of LED Indicators, which
display the conditions of the Gigabit Ethernet Switch and the status of the network.
Figure 2-1. Front Panel view of the MIL-S8000T Gigabit Ethernet Switch
Rear Panel
The rear panel of the Gigabit Ethernet Switch consists of eight Gigabit Ethernet
ports with 10/100/1000Mbps Auto-Negotiation and the DC power connecter.
Power is supplied through an external AC power adapter.
Figure 2-2. Rear Panel view of the MIL-S8000T Gigabit Ethernet Switch
4
LED Indicators
The LED indicators of the Gigabit Ethernet Switch provide a real-time indication of
system operating statuses. There are three LED-indicators for each Gigabit
Ethernet port and one Power LED for the Unit.
POWER
The Power LED indicator is solid green when the Gigabit Ethernet Switch is
receiving power.
Link/Act
The Link/Act LED indicators are solid when there is a secure connection (or link)
to the desired port. A blinking LED indicator signifies reception or transmission (i.e.
Activity—Act) of data occurring on a port.
1000Mbps
The 1000Mbps LED indicators are solid when there is a secure connection (or link)
to a 1000Mbps Gigabit Ethernet device at the desired port.
100Mbps
The 100Mbps LED indicators are solid when there is a secure connection (or link)
to a 100Mbps Fast Ethernet device at the desired port.
Note:
When the connection (or link) is 10Mbps, both the 1000Mbps and
100Mbps LED indicators are off.
5
3.
Hardware Installation
Desktop Installation
Install the MIL-S8000T Gigabit Ethernet Switch in a location that conforms to the
acceptable operation temperature and humidity ranges (see Technical
Specifications). It is recommended that the site be free from strong
electromagnetic source, vibration, dust, and direct sunlight.
A minimum of 10cm of space on the left and right hand side of the Switch is
required for ventilation purposes.
Power On
Connect the power adapter to the power socket on the Gigabit Ethernet Switch.
Connect the other end of the power pack into an appropriate electrical outlet.
Note: Use of a power adapter other than the one supplied with the Gigabit
Ethernet Switch may result in damage to the product.
6
4.
Technical Specifications
General Specifications
Standards:
Protocol:
Data Transfer Rate:
Topology:
Network Cables:
Number of Ports:
IEEE 802.3ab 1000BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3 10BASE-T
IEEE 802.3x Flow Control
CSMA/CD
Ethernet:
10Mbps (Half-duplex)
20Mbps (Full-duplex)
Fast Ethernet:
100Mbps (Half-duplex)
200Mbps (Full-duplex)
Gigabit Ethernet: 2000Mbps (Full-duplex)
Star
Ethernet:
2-pair UTP Cat. 3,4,5,
Unshielded Twisted Pair
(UTP )Cable
Fast Ethernet:
2-pair UTP Cat. 5,
Unshielded Twisted Pair
(UTP )Cable
Gigabit Ethernet: 4-pair UTP Cat. 5,
Unshielded Twisted Pair
(UTP )Cable
Eight (8) 1000BASE-T Gigabit Ethernet ports
Physical and Environmental Specifications
DC inputs:
Power Consumption:
Operating
Temperature:
Storage Temperature:
Humidity:
Dimensions:
Certification:
5V 2.4A
11.5 watts maximum
0 °C ~ 40°C
-10°C ~ 55°C
5% ~ 95% RH, non-condensing
190 x 120 x 38 mm (W x H x D)
FCC Class A, CE Marking Class A, VCCI Class A
7
Performance Specifications
Transmission
Method:
RAM Buffer:
Filtering Address
Table:
Packet
Filtering/Forwarding
Rate:
MAC Address
Learning:
Store-and-forward
256K Bytes per device
8K MAC address per device
Full wire speed
Self-learning, auto-aging
8
Appendix A:
Regulatory Information
FCC Warning
This equipment has been tested and found to comply with the regulations for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with this user’s guide, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at their own
expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
VCCI Warning
This is a product of VCCI Class A Compliance.
9
90000426 Rev A
10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising