ATCOM | AXE-800P | AX800P-AXE800P-Cento..

AX800P-AXE800P-Cento..
AX800P+2*AX210S+2*AX210X
ATCOM® Analog Card AX800P/AXE800P
Product Guide
Version: 1.0
2011-06-15
Content
CONTACT ATCOM ............................................................................................................................... 2
CHAPTER 1 THE INTRODUCTION OF AX-800P ..................................................................................... 3
CHAPTER 2 HARDWARE INTRODUCTION ............................................................................................ 4
CHAPTER 3 SOFTWARE INSTALLATION................................................................................................ 7
CHAPTER 4 SOFTWARE CONFIGURATION ........................................................................................... 9
CHAPTER 5 REFERENCE .................................................................................................................... 14
www.atcom.cn
1
Contact ATCOM
The Introduction of ATCOM
Founded in 1998, ATCOM technology has been always endeavoring in the R&D and
manufacturing of the internet communication terminals. The product line of ATCOM includes IP
Phone, IP PBX, VoIP gateway and Asterisk Card.
Contact Sales:
Address
District C, east of 2nd floor, #3, Crown industry buildings, Chegongmiao
Industry area, Futian district, Shenzhen, China
Tel
+(86)755-23487618
Fax
+(86)755-23485319
E-mail
sales@atcomemail.com
Contact Technical Support:
Tel
+(86)755-23481119
E-mail
Support@atcomemail.com
Website Address:
http://www.atcom.cn/
ATCOM Wiki Website: http://www.openippbx.org/index.php?title=Main_Page
Download Center: http://www.atcom.cn/download.html
www.atcom.cn
2
Chapter 1 the Introduction of AX800P
Overview of the AX800P/AXE800P
AX800P Asterisk card is the telephony PCI/PCI-E card that supports up to eight FXO and FXS
ports. Using AX800P analog card, open source Asterisk PBX and stand alone PC, users can create
their SOHO telephony solution which include all the sophisticated features of traditional PBX, and
extend features such as voicemail in IP PBX. The FXO and FXS modules are interchangeable to
suit various requirements.
Features
Analog card for Asterisk PBX
Support Zaptel and Dahdi driver
Support up to 8 FXO/FXS analog channels
Suitable for SOHO PBX / VoiceMail / IVR.
Caller ID and Call waiting
Conference
Applications
IP PBX
IVR system
Small Office Home Office
Traditional Calls/VoIP Calls Conference
Hardware Requirement
500-Mhz Pentium III
64MB RAM
3.3V or 5V PCI 2.2 slot
PCI Card Dimension:
AX800P: 169mm (length) × 98mm (height)
AXE800P: 169mm (length) × 110mm (height)
www.atcom.cn
3
Chapter 2 Hardware Introduction
Hardware Configuration
Motherboard: AX-800P
Dual ports FXS module: AX-210S
Dual ports FXO module: AX-210X
Splitter: SP400
Customers can use the combination of AX-210S, AX-210X, AX-210XS modules according to
their requirements. One AX-210S module supports two FXS ports, one AX-210X module supports
two FXO ports, One AX-210XS module supports one FXS port and one FXO port.
AX800P+2*AX210S+2*AX210X
Port 1 and port 2 are RJ45 interfaces, the port is connected to a splitter, the splitter supports one
RJ45 port and 4 RJ11 ports.
Near the port 1 and port 2, there are LEDs, when the driver of the card is loaded correctly, the
LEDs will be green.
Clock connector is used to connect to ISDN PRI card, in this way the analog card can synchronize
with Telecom through PRI line, it is good for receiving fax if you connect your fax to fxs port
directly.
Attention: If you want to use FXS port, you have to provide the card with 12V power(4 Pin power
cable).
Warning: Please do not plug and unplug the card, modules when the PC power is on.
www.atcom.cn
4
AXE800P
AX-210S
www.atcom.cn
AX-210XS
AX-210X
5
SP400
www.atcom.cn
6
Chapter 3 Software Installation
Test Environment:
asterisk-1.6.1.12
dahdi-linux-2.2.0.2
dahdi-tools-2.2.0
Centos 5.4
AX-800P+210S+210X
After inserting the card into your PCI slot and boot your server, please use the “lspci -vv”
command to check the PCI bus compatibility. The correct output will like the following:
---------------------------------------------------------------------------------------------------------------------05:04.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
---------------------------------------------------------------------------------------------------------------------A Tiger Jet device will be found, if you can not see the Tiger Jet device, please poweroff your
server and try another PCI slot, if it still does not help, you have to check the compatibility issue
between the card and your PCI bus.
1.
To install asterisk and dahdi, we have to install the following prerequisite packages:
bison bison-devel zlib zlib-devel openssl openssl-devel gnutls-devel gcc gcc-c++
Please use the yum install command to install the above packages.
2.
Download asterisk,dahdi-linux and dahdi-tools
[root@localhost src]#
wget http://downloads.asterisk.org/pub/telephony/asterisk/releases/asterisk-xx
[root@localhost src]#
wget http://downloads.asterisk.org/pub/telephony/dahdi-linux/releases/dahdi-linux-xx
[root@localhost src]#
wget http://downloads.asterisk.org/pub/telephony/dahdi-tools/releases/dahdi-tools-xx
3.
Install asterisk,dahdi-linux and dahdi-tools
Install dahdi-linux and Rectify wctdm.c
1) [root@localhost src]# tar -xvzf dahdi-linux-2.2.0.2.tar.gz
2) [root@localhost src]# cd dahdi-linux-2.2.0.2/drivers/dahdi/
3) rm –rf wctdm.c
4) wget http://www.atcom.cn/downloads/TelephonyCard/drivers/AX-1600P/wctdm.c.v1.6
5) mv wctdm.c.v1.6 wctdm.c
6) [root@localhost src]# cd dahdi-linux-2.2.0.2
[root@localhost dahdi-linux-2.2.0.2]# make
7) [root@localhost dahdi-linux-2.2.0.2]# make install
www.atcom.cn
7
Install dahdi-tools
1) [root@localhost src]# tar -xvzf dahdi-tools-2.2.0.tar.gz
2) [root@localhost src]# cd dahdi-tools-2.2.0
3) [root@localhost dahdi-tools-2.2.0]# ./configure
4) [root@localhost dahdi-tools-2.2.0]# make
5) [root@localhost dahdi-tools-2.2.0]# make install
Install asterisk
1) [root@localhost src]# tar -xvzf asterisk-1.6.1.12.tar.gz
2) [root@localhost src]# cd asterisk-1.6.1.12
3) [root@localhost asterisk-1.6.1.12]# ./configure
4) [root@localhost asterisk-1.6.1.12]# make
5) [root@localhost asterisk-1.6.1.12]# make install
6) [root@localhost asterisk-1.6.1.12]# make samples
www.atcom.cn
8
Chapter 4 Software Configuration
1. Please check if the AX-800P driver has been loaded successfully, run cat /proc/interrupts
command and you should see one line with wctdm.
If you can not see wctdm, you can try to poweroff your server and replug AX-800P into
another PCI slot.
2. Please use the “dahdi_genconf” command to configure the /etc/dahdi/system.conf file and
generate /etc/asterisk/dahdi-channels.conf file.
[root@localhost ~]# dahdi_genconf
It does not show any output if dahdi_genconf runs successfully.
system.conf
---------------------------------------------------------------------------------------------------------------# Span 1: WCTDM/16 "Wildcard TDM400P REV E/F Board 17" (MASTER)
fxsks=1
echocanceller=mg2,1
fxsks=2
echocanceller=mg2,2
fxsks=3
echocanceller=mg2,3
fxsks=4
echocanceller=mg2,4
fxsks=5
echocanceller=mg2,5
fxsks=6
echocanceller=mg2,6
fxsks=7
echocanceller=mg2,7
fxsks=8
# Global data
loadzone
= us (According to your country)
defaultzone
= us (According to your country)
----------------------------------------------------------------------------------------------------------------
www.atcom.cn
9
dahdi-channels.conf
---------------------------------------------------------------------------------------------------------------; Span 1: WCTDM/16 "Wildcard TDM400P REV E/F Board 17" (MASTER)
;;; line="1 WCTDM/16/0 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 1
callerid=
group=
context=default
;;; line="2 WCTDM/16/1 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 2
callerid=
group=
context=default
;;; line="3 WCTDM/16/2 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 3
callerid=
group=
context=default
;;; line="4 WCTDM/16/3 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 4
callerid=
group=
context=default
;;; line="5 WCTDM/16/4 FXSKS"
signalling=fxs_ks
www.atcom.cn
10
callerid=asreceived
group=0
context=from-pstn
channel => 5
callerid=
group=
context=default
;;; line="6 WCTDM/16/5 FXSKS (SWEC: MG2)"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 6
callerid=
group=
context=default
;;; line="7 WCTDM/16/6 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 7
callerid=
group=
context=default
;;; line="8 WCTDM/16/7 FXSKS (SWEC: MG2)"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 8
callerid=
group=
context=default
www.atcom.cn
11
[root@localhost ~]# dahdi_cfg –vv
The right output of running dahdi_cfg –vv will like the following:
DAHDI Tools Version - 2.2.0
DAHDI Version: 2.2.0.2
Echo Canceller(s): MG2
Configuration
======================
Channel map:
Channel 01: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 01)
Channel 02: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 02)
Channel 03: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 03)
Channel 04: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 04)
Channel 05: FXS Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 05)
Channel 06: FXS Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 06)
Channel 07: FXS Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 07)
Channel 08: FXS Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 08)
8 channels to configure.
Setting echocan for channel 1 to mg2
Setting echocan for channel 2 to mg2
Setting echocan for channel 3 to mg2
Setting echocan for channel 4 to mg2
Setting echocan for channel 5 to mg2
Setting echocan for channel 6 to mg2
Setting echocan for channel 7 to mg2
Setting echocan for channel 8 to mg2
3. Please add the following line in the end of chan_dahdi.conf file
#include dahdi-channels.conf
4. Please run asterisk with the following command:
asterisk –vvgc
reload
www.atcom.cn
12
5. Please run dahdi show channels command
The right output should like the following:
Chan Extension Context
Language
pseudo
default
1
from-internal
2
from-internal
3
from-internal
4
from-internal
5
from-pstn
6
from-pstn
7
from-pstn
8
from-pstn
www.atcom.cn
MOH Interpret
default
default
default
default
default
default
default
default
default
Blocked
State
In Service
In Service
In Service
In Service
In Service
In Service
In Service
In Service
In Service
13
Chapter 5 Reference
http://www.asteriskguru.com/
http://www.asterisk.org/downloads
http://www.openippbx.org/index.php?title=Main_Page
http://www.atcom.cn/
www.atcom.cn
14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising