Allied Telesis | AT-9410GB | Installation guide | Allied Telesis AT-9410GB Installation guide

Allied Telesis AT-9410GB Installation guide
Gigabit
Ethernet
Switch
AT-9410GB
K
Installation
Guide
PN 613-50289-00 Rev A
®
Copyright  2002 Allied Telesyn, Inc.
960 Stewart Drive Suite B, Sunnyvale, CA 94085 USA
All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn, Inc.
All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks
of their respective owners.
Allied Telesyn, Inc. reserves the right to make changes in specifications and other information contained in this document without
prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesyn, Inc. be
liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising
out of or related to this manual or the information contained herein, even if Allied Telesyn, Inc. has been advised of, known, or
should have known, the possibility of such damages.
Electrical Safety and Emission
Statement
Standards: This product meets the following standards.
U.S. Federal Communications Commission
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with this instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
Note: Modifications or changes not expressly approved by the manufacturer or the FCC can void your right to operate this
equipment.
Canadian Department of Communications
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
RFI Emission
FCC Class A, EN55022 Class A, CISPR22 Class A (VCCI), AS/NZS3548(CTICK), EN61000-3-2, EN61000-3-3
1
Warning: In a domestic environment this product may cause radio interference in which case the user may be required to take
2
adequate measures.
Immunity
EN55024
3
Electrical Safety
UL 1950 (UL/cUL)), EN60950
Laser
EN60825
5
4
Important: Appendix C contains translated safety statements for installing this equipment. When you see the
C for the translated safety statement in your language.
Wichtig: Anhang C enthält übersetzte Sicherheitshinweise für die Installation dieses Geräts. Wenn Sie
Anhang C den übersetzten Sicherheitshinweis in Ihrer Sprache nach.
, go to Appendix
sehen, schlagen Sie in
Vigtigt: Tillæg C indeholder oversatte sikkerhedsadvarsler, der vedrører installation af dette udstyr. Når De ser symbolet
De slå op i tillæg C og finde de oversatte sikkerhedsadvarsler i Deres eget sprog.
Belangrijk: Appendix C bevat vertaalde veiligheidsopmerkingen voor het installeren van deze apparatuur. Wanneer u de
raadpleeg Appendix C voor vertaalde veiligheidsinstructies in uw taal.
, skal
ziet,
Important : L'annexe C contient les instructions de sécurité relatives à l'installation de cet équipement. Lorsque vous voyez le
symbole
, reportez-vous à l'annexe C pour consulter la traduction de ces instructions dans votre langue.
Tärkeää: Liite C sisältää tämän laitteen asentamiseen liittyvät käännetyt turvaohjeet. Kun näet
turvaohjetta liitteestä C.
-symbolin, katso käännettyä
Importante: l’Appendice C contiene avvisi di sicurezza tradotti per l’installazione di questa apparecchiatura. Il simbolo
di consultare l’Appendice C per l’avviso di sicurezza nella propria lingua.
Viktig: Tillegg C inneholder oversatt sikkerhetsinformasjon for installering av dette utstyret. Når du ser
for å finne den oversatte sikkerhetsinformasjonen på ønsket språk.
, indica
, åpner du til Tillegg C
Importante: O Anexo C contém advertências de segurança traduzidas para instalar este equipamento. Quando vir o símbolo
leia a advertência de segurança traduzida no seu idioma no Anexo C.
,
Importante: El Apéndice C contiene mensajes de seguridad traducidos para la instalación de este equipo. Cuando vea el símbolo
, vaya al Apéndice C para ver el mensaje de seguridad traducido a su idioma.
Obs! Bilaga C innehåller översatta säkerhetsmeddelanden avseende installationen av denna utrustning. När du ser
till Bilaga C för att läsa det översatta säkerhetsmeddelandet på ditt språk.
, skall du gå
iii
Table of Contents
Preface ...................................................................................................................................................................................................................... 6
How This Guide is Organized ............................................................................................................................................................................. 6
Document Conventions ...................................................................................................................................................................................... 7
Where to Find Web-based Guides ................................................................................................................................................................... 8
Contacting Allied Telesyn ................................................................................................................................................................................... 9
Management Software Updates ....................................................................................................................................................................10
Chapter 1
Product Description .........................................................................................................................................................................................11
Summary of Features ..........................................................................................................................................................................................11
Location of Components ...................................................................................................................................................................................12
Hardware Features ..............................................................................................................................................................................................13
10/100/1000Base-T Twisted Pair Ports ................................................................................................................................................ 13
Gigabit Interface Converter (GBIC) Expansion Slots ....................................................................................................................... 17
System LED .................................................................................................................................................................................................... 18
10/100/1000 Mbps Port LEDs.................................................................................................................................................................. 19
GBIC Port LEDs.............................................................................................................................................................................................. 20
RS-232 Terminal Port.................................................................................................................................................................................. 21
AC Power Connector.................................................................................................................................................................................. 22
Software Features ................................................................................................................................................................................................23
AT-S45 Management Software .............................................................................................................................................................. 23
Spanning Tree Protocol (STP) ................................................................................................................................................................. 26
Tagged and Port-based VLANs............................................................................................................................................................... 27
Quality of Service (QoS)............................................................................................................................................................................. 27
IGMP Snooping ............................................................................................................................................................................................ 28
Dynamic Host Configuration Protocol (DHCP) ................................................................................................................................. 29
Port Monitoring............................................................................................................................................................................................ 29
Port Trunking ................................................................................................................................................................................................ 29
Port Security .................................................................................................................................................................................................. 32
A Few Basics to Ethernet Switching ..............................................................................................................................................................33
MAC Address Table..................................................................................................................................................................................... 33
Duplex Mode................................................................................................................................................................................................. 34
Store and Forward....................................................................................................................................................................................... 34
Backpressure and Flow Control ............................................................................................................................................................. 34
Network Topologies ............................................................................................................................................................................................36
Power Workgroup Topology................................................................................................................................................................... 36
Collapsed Backbone - Switch Topology 1 .......................................................................................................................................... 37
Collapsed Backbone - Switch Topology 2 .......................................................................................................................................... 38
iv
Chapter 2
Installation ............................................................................................................................................................................................................39
Installation Safety Precautions ........................................................................................................................................................................40
Selecting a Site for the Switch .........................................................................................................................................................................42
Required Cables ....................................................................................................................................................................................................43
Unpacking the Switch ........................................................................................................................................................................................44
Installing the Switch on a Desktop ................................................................................................................................................................45
Installing the Switch in a Rack .........................................................................................................................................................................46
Installing an Optional GBIC Module ..............................................................................................................................................................48
Cabling the Switch ...............................................................................................................................................................................................50
Powering On the Switch ....................................................................................................................................................................................53
Starting a Local Management Session .........................................................................................................................................................54
Warranty Registration .........................................................................................................................................................................................57
Chapter 3
Troubleshooting ................................................................................................................................................................................................58
Appendix A
Technical Specifications .................................................................................................................................................................................61
Physical Specifications .......................................................................................................................................................................................61
Environmental Specifications ..........................................................................................................................................................................61
Power Specifications ...........................................................................................................................................................................................61
Safety and Electromagnetic Emissions Certifications .............................................................................................................................62
Standards ................................................................................................................................................................................................................62
SNMP Support .......................................................................................................................................................................................................62
Appendix B
Default Switch Settings ..................................................................................................................................................................................63
Appendix C
Translated Electrical Safety and Emission Information ..................................................................................................................65
v
Preface
This guide contains instructions on how to install an AT-9410GB
Gigabit Ethernet Switch.
How This Guide is Organized
This manual contains the following chapters and appendices:
Chapter 1, Hardware Description, describes the features and
components of the switch.
Chapter 2, Installation, contains the installation instructions.
Chapter 3, Troubleshooting, provides information on how to resolve
common problems that might occur with the switch.
Appendix A, Technical Specifications, contains the switch’s technical
specifications.
Appendix B, Switch Default Settings, lists the factory default settings.
Appendix C, Translated Electrical Safety and Emission Information,
contains translations of the warnings and cautions in the manual.
6
AT-9410GB Installation Guide
Document Conventions
This document uses the following conventions to highlight important
information.
Note
Notes provide additional information.
Warning
Warnings inform you that performing or omitting a specific action
may result in bodily injury.
Caution
Cautions inform you that performing or omitting a specific action
may result in equipment damage or loss of data.
7
Preface
Where to Find Web-based Guides
The Allied Telesyn web site at www.alliedtelesyn.com contains the most
recent documentation for all Allied Telesyn products. All documents are
available as PDF files. You can either view the documents online or
download them onto a local workstation or server.
Once you have installed the switch, refer to following manual for
instructions on how to manage and configure the unit. The manual is
available from the Allied Telesyn web site:
❑
8
AT-S45 Management Software User’s Guide
PN 613-50290-00
AT-9410GB Installation Guide
Contacting Allied Telesyn
Telephone
Support
To contact Technical Support by telephone, find your country or region
in the table below.
United States and Canada
Tel: 1 800 428 4835 (option 4)
Europe, Africa, and the Middle
East
Tel: 00 800 287 877 67* or
+31 20 711 4333
(Finland only: Tel: 990 287 877 67)
Asia and Southeast Asia
Tel: (++65) 381 5612
Australia
Tel: 1 800 000 880
New Zealand
Tel: 0800 45 5782
(* Valid in Austria, Belgium, France, Germany, Ireland, Italy, Luxembourg, The
Netherlands, Norway, Sweden, Switzerland and the United Kingdom. For other
European countries not listed here, ring +31 20 711 4333.)
Online Support
For Sales or
Corporate
Information
You can also contact Technical Support online at
http://kb.alliedtelesyn.com.
Allied Telesyn, Inc.
19800 North Creek Parkway,
Suite 200
Bothell, WA 98011
Tel:1 (425) 487-8880
Fax:1 (425) 489-9191
9
Preface
Management Software Updates
Allied Telesyn periodically updates the management software programs
for our managed products. To obtain a copy of an updated management
program, you can download the software either from our web site or our
FTP server at ftp.alliedtelesyn.com. To use the FTP server, enter
‘anonymous’ for the user name when you log in and your e-mail address
for the password.
10
Chapter 1
Product Description
The AT-9410GB is a Layer 2 Gigabit Ethernet switch. It offers a wide range
of features and capabilities, all designed to simplify the task of creating
and maintaining a Gigabit Ethernet network.
Summary of Features
G
G
G
G
G
G
G
G
G
G
G
G
11
Ten 10/100/1000Base-T ports with RJ-45 connectors
Two Gigabit Interface Converter (GBIC) module expansion slots
Auto-MDI/MDI-X on all twisted pair ports
Auto-Negotiation for speed and duplex mode (IEEE 803.3ucompliant)
Port trunking and port monitoring
Port security
Dynamic Host Configuration Protocol
Internet Group Management Protocol snooping
AT-S45 management software
Port-based and tagged VLANs (IEEE 802.1Q-compliant)
Spanning tree protocol (IEEE 802.1d-compliant)
Quality of Service (IEEE 802.1p-compliant)
Product Description
Location of Components
Figure 1 illustrates the front panel of the AT-9410GB Gigabit Ethernet
Switch.
RS232
Terminal Port
AT-9410GB
12-Port Gigabit Managed Switch
RS232
10GbE
10/100Mbps
ACT
PWR
Port LEDs
System LED
LINK
LINK
FDX
GBIC1
10/100/1000Base-T Ports
GBIC2
GBIC Expansion
Slots
Figure 1 AT-9410GB Front Panel
Figure 2 illustrates the back panel.
100-240VAC
AC Power
Connector
Figure 2 Back Panel
12
AT-9410GB Installation Guide
Hardware Features
The following sections describe these hardware features of the AT9410GB Gigabit Ethernet Switch:
G
G
G
G
G
G
G
10/100/
1000Base-T
Twisted Pair
Ports
10/100/1000 Base-T Ports
Gigabit Interface Converter (GBIC) Expansion Slots
System LED
Port LEDs
Gigabit Connector LEDs
RS-232 Terminal Port
AC Power Connector
10GbE
/100Mbps
ACT
FDX
Figure 3 Twisted Pair Ports
The AT-9410GB Gigabit Ethernet Switch features 10 twisted pair ports.
Type of Connector
All of the twisted pair ports feature RJ-45 connectors. (For the port
pinout details, refer to RJ-45 Port Pinouts in the next section.)
Speed
The 10/100/1000Base-T ports are capable of 10 Mbps, 100 Mbps, or 1000
Mbps speeds. You can set the port speed manually or, since the ports are
IEEE 802.3 Auto-Negotiation compliant, you can let the switch set each
port’s speed automatically. With Auto-Negotiation, the switch
automatically matches the highest possible common speed between
each switch port and each end node. For example, if an end node is
capable of only 10 Mbps, the switch sets the port connected to the end
node to 10 Mbps.
Note
Auto-Negotiation is activated as the default on ports 1 through 10.
To deactivate Auto-Negotiation and set the speeds manually, refer
to the AT-S45 Management Software User’s Guide.
13
Product Description
Maximum Distance
Each twisted pair port has a maximum operating distance of 100 m (328
ft).
Type of Cabling
For 10 Mbps operation on the twisted pair ports, Category 3 or better
100 ohm shielded or unshielded twisted pair cabling is required. For 100
or 1000 Mbps operation on the twisted pair ports, Category 5 and
Enhanced Category 5 (5E) 100 ohm shielded or unshielded twisted pair
cabling is required.
Auto-MDI
All of the twisted pair ports on the switch are auto-MDI and IEEE
802.3ab-compatible. They automatically configure themselves as either
MDI or MDI-X when operating at 10 Mbps or 100 Mbps. This feature
allows you to use either straight-through or crossover twisted pair
cables to connect devices to the ports.
Duplex Mode
Each twisted pair port on the switch can operate in either half- or fullduplex mode. The twisted pair ports are IEEE 802.3u-compliant and will
Auto-Negotiate the duplex mode setting by default. If the end node
connected to a twisted pair port on the switch is capable of full-duplex
operation, the switch sets the port to full-duplex. If the end node is
capable of only half-duplex, the port is set to half-duplex.
If desired, Auto-Negotiation on one or all of the twisted pair ports can be
disabled so that you can set the duplex mode manually through the
switch’s management software.
14
AT-9410GB Installation Guide
RJ-45 Port Pinouts
Figure 4 illustrates the pin layout to an RJ-45 connector and port.
1
8
8
1
Figure 4 RJ-45 Connector and Port Pin Layout
Table 1 lists the RJ-45 pin signals when a twisted pair port is operating in
the MDI configuration.
Table 1 MDI Pin Signals (10/100 Mbps)
Pin
Signal
1
TX+
2
TX-
3
RX+
6
RX-
Table 2 lists the RJ-45 port pin signals when a twisted pair port is
operating in the MDI-X configuration.
Table 2 MDI-X Pin Signals (10/100 Mbps)
Pin
Signal
1
RX+
2
RX-
3
TX+
6
TX-
15
Product Description
Table 3 lists the RJ-45 connector pins and their signals when a twisted
pair port is operating at 1000 Mbps.
Table 3 1000 Mbps Pin Signals
16
Pin
Pair
Signal
1
0
TX and RX+
2
0
TX and RX-
3
1
TX and RX+
4
2
TX and RX+
5
2
TX and RX-
6
1
TX and RX-
7
3
TX and RX+
8
3
TX and RX-
AT-9410GB Installation Guide
Gigabit
Interface
Converter
(GBIC)
Expansion Slots
LINK
LINK
GBIC1
GBIC2
Figure 5 GBIC Expansion Slots
The AT-9410GB Gigabit Ethernet Switch has two expansion slots on the
front panel, labeled GBIC1 and GBIC2. Each slot can accommodate one
optional GBIC module.
A GBIC module is a gigabit (1000Base) transceiver. Figure 6 shows an
example of a fiber optic GBIC module. You can use GBIC modules to
quickly and easily add additional Gigabit Ethernet ports to your switch.
Figure 6 Example of a GBIC Module
GBIC modules can be used to extend the distance of your network, build
a high-speed backbone network, or connect additional nodes to the
network, such as high-speed servers.
The AT-9410GB Gigabit Ethernet Switch supports the AT-G8 series GBIC
modules: SX, LX, LX25, LX40, LX75.
17
Product Description
System LED
AT-9410GB
12-Port Gigabit Managed Switch
RS232
10GbE
10/100Mbps
ACT
System LED
PWR
FDX
Figure 7 System LEDs
The system LED is defined in Table 4.
Table 4 System LEDs
LED
State
Description
Power
Amber
The switch is booting up or downloading software.
Green
System power is ON.
OFF
System power is OFF.
18
AT-9410GB Installation Guide
10/100/1000
Mbps Port LEDs
10GbE
10/100Mbps
ACT
FDX
Port LEDs
Figure 8 10/100/1000 Mbps Port LEDs
The 10/100/1000 Mbps port LEDs on the front panel display port status
information for Ports 1 through 10. Each 10/100/1000 Mbps port has
four LEDs.
Table 5 describes the 10/100/1000 Mbps port LEDs.
Table 5 10/100/1000 Port LEDs
LED
State
Description
1GbE
Green
A 1000 Mbps link has been established.
OFF
No link has been established or a 10/100 Mbps link
has been established.
Green
A 10/100 Mbps link has been established.
OFF
No link has been established or a 1000 Mbps link
has been established.
Flashing Green
There is activity on the port.
Green
A link has been established but there is no activity
on the port.
OFF
No link has been established.
Green
The port is operating in full-duplex mode.
Flashing Green
The port is operating in half-duplex mode with
data collisions occurring on the port.
OFF
No link has been established or the port is operating in half-duplex mode with no data collisions.
10/100Mbps
ACT (Activity)
FDX (Full Duplex)
19
Product Description
GBIC Port LEDs
LINK
LINK
GBIC1
GBIC2
GBIC Port LEDs
Figure 9 GBIC Port LEDs
Ports GBIC1 and GBIC2 each have a LINK LED on the front panel that
indicates whether or not the GBIC expansion slot is in use.
The GBIC LINK LEDs are defined in Table 6.
Table 6 GBIC LEDs
LED
State
Description
Port GBIC1 LINK
Green
A GBIC has been installed.
OFF
No link has been established.
Green
A GBIC has been installed.
OFF
No link has been established.
Port GBIC2 LINK
20
AT-9410GB Installation Guide
RS-232
Terminal Port
AT-9410GB
12-Port Gigabit Managed Switch
RS232
10GbE
10/100Mbps
ACT
PWR
FDX
RS232 Terminal
Port
Figure 10 RS232 Terminal Port
The RS-232 Terminal Port is used to establish a local (out-of-band)
management session with the switch. Using the port, you can access the
switch’s management software and configure the switch’s operating
parameters.
You establish a local management session by connecting either a VT100
terminal or a personal computer with a terminal emulation program to
the port.
Note
You are not required to manage an AT-9410GB Gigabit Ethernet
Switch. The default switch settings may be sufficient for your
network, in which case you can use the unit as an unmanaged
switch. For the switch’s default settings, refer to Default Switch
Settings on page 63.
The RS-232 Terminal Port uses a null modem cable.
The default settings for the RS-232 Terminal Port are:
G Emulation mode: VT100
G Baud rate: 9600
G Data bits: 8
G Parity: None
G Stop bits: 1
G Flow control: None
G Key mode: Terminal keys
21
Product Description
AC Power
Connector
100-240VAC
Figure 11 AC Power Connector
The switch has a single AC power supply socket on the back panel,
which has auto-switch AC inputs. Refer to Appendix A, Technical
Specifications, for the input voltage range. The unit does not have a
power switch. To power ON or OFF the switch, you connect or
disconnect the power cord.
22
AT-9410GB Installation Guide
Software Features
The following sections describe these software features:
G
G
G
G
G
G
G
G
AT-S45 Management Software
Spanning Tree Protocol (STP)
Tagged and Port-based Virtual LANs (VLANs)
Quality of Service
Dynamic Host Configuration Protocol (DHCP)
Port Mirroring
Port Trunking
Port Security
Note
All of the features described here are further described in the
AT-S45 Management Software User’s Guide.
AT-S45
Management
Software
The AT-9410GB Gigabit Ethernet Switch comes with the AT-S45
management software pre-installed. This management software comes
with default values for all the operating parameters for the switch. In
some network environments, the default settings might not need to be
changed, allowing you to use the switch as an unmanaged switch.
If you want to manage the switch and change or monitor the operating
parameters, you must access the AT-S45 management software. Some
of the management software functions include assigning the switch an
IP address and subnet mask, creating VLANs and port trunks, and
activating and configuring the Spanning Tree Protocol parameters.
The management software’s interface consists of menus and prompts
that make it easy for you to configure the switch and view performance
and status information.
There are four different ways to access the switch’s management
software:
G
G
G
G
RS-232 Terminal Port
Web Browser
Telnet Application Protocol
SNMP management program
23
Product Description
RS-232 Terminal Port
One method for accessing the management software is by connecting a
terminal or a PC with a terminal emulation program to the RS-232
Terminal Port on the switch, as indicated in Figure 12. This is commonly
referred to as local or out-of-band management. Please refer to Starting
a Local Management Session on page 54 for instructions on how to
manage the switch using this method.
AT-9410GB
12-Port Gigabit Managed Switch
RS232
10GbE
10/100Mbps
ACT
PWR
FDX
Figure 12 Local Management
Once the session has been established using “manager” as both the
default login name and default password, the management software’s
Main Menu is displayed on the terminal’s screen, as shown in Figure 13.
AT-9410GB Local Management System
Main Menu
[G]eneral Information
[B]asic Switch Configuration...
[A]dvanced Switch Configuration...
Switch [T]ools...
[S]tatistics
[Q]uit
Command>
Enter the character in square brackets to select option
Figure 13 AT-S45 Main Menu - Local Management Session
24
AT-9410GB Installation Guide
Web Browser
You can also manage the switch from a workstation on your network
using a web browser, such as Netscape Navigator. This is referred to as
remote or in-band management.
To start a web browser management session, you simply enter the
switch’s IP address in the URL field of the web browser, as shown in
Figure 14, and enter “manager” as both the default login name and
default password.
URL Field with Switch IP Address
Figure 14 URL Field of a Web Browser
Figure 15 shows the AT-S45 management software’s home page.
Figure 15 Web Browser Management Home Page
25
Product Description
Telnet Application Protocol
Using the Telnet application protocol is another way for you to manage
the switch remotely from a workstation on your network. Starting this
type of remote access requires that you specify the IP address of the
switch in the Telnet protocol and enter “manager” as both the default
login name and default password.
SNMP Management
You can also manage a switch with an SNMP management program,
such as HP Openview. This management method requires loading the
AT-9410GB Gigabit Ethernet Switch MIBs onto the workstation from
which you intend to manage the switch. The Allied Telesyn Enterprise
MIB is available in the software upgrades on the Allied Telesyn web site.
The MIB standards supported by this switch include:
G
G
G
Spanning Tree
Protocol (STP)
RFC 1213 (MIB II)
RFC 1493 (Bridge MIB)
Allied Telesyn Enterprise MIB
The AT-9410GB Gigabit Ethernet Switch is IEEE 802.1D standardcompliant and supports the spanning tree protocol. STP can be an
important part of large networks where loops exist in the network
topology.
A loop occurs when two or more nodes on your network can transmit
data to each other over more than one link. Network loops can seriously
impact network performance because packets can become caught in
repeating cycles, often referred to as broadcast storms, that needlessly
consume network bandwidth and reduce network performance.
STP addresses this problem by ensuring that there is only one path
between the end nodes. Where multiple paths exist, STP places the extra
paths in a redundant or standby mode, leaving only one main active
path. The redundant paths can be activated by STP if the main path goes
down. So not only does STP guard against multiple links between end
nodes, but it also activates backup redundant paths in case a main link
fails.
STP is disabled by default on the AT-9410GB Gigabit Ethernet Switch.
Note
The AT-9410GB Gigabit Ethernet Switch supports only one STP
domain. All virtual LANs that you create will be members of that
STP domain.
26
AT-9410GB Installation Guide
Tagged and
Port-based
VLANs
A VLAN is a group of end nodes that form an independent subnetwork.
Each VLAN constitutes a separate broadcast domain, where the frames
of a VLAN are not allowed to cross the VLAN boundary.
VLANs can be extremely useful in improving network performance and
increasing network security. You can create VLANs to group the
workstations, servers, and other networking equipment connected to
your switches into logical workgroups. These VLAN groupings can be
based on similar data needs or security requirements. When networking
devices, such as workstations and servers, are grouped into a VLAN, data
is exchanged between only those members of the group.
Other advantages of VLANs include:
G
G
G
G
You can group workstations logically or functionally, regardless of
their physical location on the network.
You can change VLAN memberships anytime by software
configuration without moving the workstations physically or
having to move cables from one port to another on the switch.
With VLAN tagging, network servers or other network resources
can be shared among several VLANs without loss of data isolation
or security.
A VLAN can consist of ports limited to a single switch or ports from
multiple switches. This allows you to group together network
devices that, though physically separated by large distances, will
function as if they are a part of the same physical LAN.
The AT-9410GB Gigabit Ethernet Switch supports two types of VLANs:
G
G
Port-based VLANs
Tagged VLANs
The AT-9410GB Gigabit Ethernet Switch comes configured with one
port-based VLAN, called the Default VLAN.
Quality of
Service (QoS)
The AT-9410GB Gigabit Ethernet Switch supports the IEEE 802.1p
standard for Quality of Service. QoS can be important in network
environments where there are time-critical applications, such as voice
transmission or video conferencing, that can be adversely affected by
packet transfer delays.
Prior to QoS, network traffic was handled in a best-effort manner. File
transfer delays did occur, but were mostly transparent to network users.
But with the introduction of time-critical applications, packet transfer
delays can impact performance. For example, delays in packets carrying
voice transmission can result in poor audio quality.
27
Product Description
The QoS feature was designed to address this problem. With it, Ethernet
frames can be assigned different priorities. The switch uses the priorities
when determining which frames to forward first. Frames from endnodes running time-critical applications can be given a high priority, so
that they will be forwarded by the switch ahead of less time-critical
frames.
IGMP Snooping
The Internet Group Management Protocol (IGMP) enables routers to
create lists of nodes that want to receive multicast packets from a
multicast application. The router creates a multicast membership list by
periodically sending out queries to the local area networks connected to
its ports. A node wanting to become a member of a particular multicast
group responds to a query by sending a report. Nodes that join a
multicast group are referred to as host nodes.
Once the router has received a request from a host node to join a
multicast group, it notes the multicast group that the host node wants
to join and the port on the router where the node is located. Any
multicast packets belonging to that multicast group are then forwarded
by the router out the port. If a particular port on the router has no nodes
that want to be members of multicast groups, the router does not send
multicast packets out the port. This improves network performance by
restricting multicast packets only to router ports where host nodes are
located.
The IGMP snooping feature on the AT-9410GB Switch enables the unit to
monitor the flow of queries from the router and reports from the host
nodes to build its own multicast membership lists. It uses the lists to
forward multicast packets only to switch ports where there are host
nodes that are members of multicast groups. This improves switch
performance and network security by further restricting the flow of
multicast packets only to those switch ports connected to host nodes.
Without IGMP snooping, the switch would flood all multicast packets
out all of its ports, except the port on which it received the packet. Such
flooding of packets can negatively impact switch and network
performance.
Note
By default, IGMP snooping is disabled on the switch.
Note
The AT-S45 software supports both IGMP version 1 and version 2.
28
AT-9410GB Installation Guide
Dynamic Host
Configuration
Protocol
(DHCP)
This application protocol was developed to simplify network
management. It is used to automatically assign IP configuration
information to the devices on your network, such as an IP address,
subnet mask, and, in some instances, a default gateway address.
The AT-9410GB Gigabit Ethernet Switch supports this protocol and can
obtain its IP configuration information from a DHCP server on your
network. If you activate this feature, the switch will seek its IP address,
subnet mask, and gateway from a DHCP server. Naturally, for this to
work there must be a DHCP server residing on your network.
Most DHCP services allow you to specify whether the IP address
assignment from the server is to be static or dynamic. If you choose
static, the server will always assign the same IP address to the switch
when the switch is reset or powered on. If you choose dynamic, the
server will assign an unused IP address from its list of potential IP
addresses each time the switch is reset or powered on.
Note
The DHCP option is disabled by default on the switch.
Port Monitoring
The port monitoring feature allows you to unobtrusively monitor the
traffic being received and transmitted on a port on the switch by having
the traffic copied to another switch port. You can connect a network
analyzer to the port functioning as the monitoring port to monitor the
traffic without impacting network performance or speed.
Port Trunking
Port trunking is an economical way for you to increase the bandwidth
between an AT-9410GB Gigabit Ethernet Switch and another network
device, such as a server, router, workstation, or another switch. A port
trunk is two or more data ports that have been grouped together to
increase the bandwidth between a switch and a network node by
functioning as one logical path. This increase in bandwidth can prove
useful in situations where a single connection between the switch and a
node is insufficient to handle the traffic load.
Port trunks are also useful in adding redundancy to the critical devices of
your network. If one link of a port trunk fails, the remaining links will
continue to provide a connection to the end node.
Despite the software configuration and physical connections, there are
no data loops in a port trunk because of load balancing. The port trunk
always sends packets from a particular source to a particular destination
over the same link within the trunk. A single link is designated for
flooding broadcasts and packets of unknown destination.
29
Product Description
Below are the guidelines to follow when planning a port trunk:
G
G
G
The switch can support up to four port trunks at a time.
The duplex mode, speed, and flow control settings must be the
same for all of the ports in a trunk.
When cabling a trunk, the order of the connections should be
maintained on both nodes. The lowest numbered port in a trunk
on the switch should be connected to the lowest numbered port
of the trunk on the other device, the next lowest numbered port
on the switch should be connected to the next lowest numbered
port on the other device, and so on.
For example, assume that you are connecting a trunk between
two AT-9410GB switches. On the first AT-9410GB switch you
had chosen ports 2, 3, 4, and 5 for the trunk. On the second AT9410GB switch you had chosen ports 1, 2, 3, and 4. To maintain
the order of the port connections, you would connect port 2
on the first AT-9410GB switch to port 1 on the second AT9410GB, port 3 to port 2, and so on.
G
G
G
The ports of a port trunk must be of the same type. For example,
they can be all twisted pair ports or all GBIC ports.
You can create a port trunk of the GBIC modules installed in the
GBIC1 and GBIC2 slots, provided that the GBIC modules are of the
same type.
The ports on the end node must also be configured as a port
trunk.
Caution
Do not connect the cables of a port trunk to the switch until after
you have created the port trunk using the switch’s management
software. Connecting the cables before the port trunk has been
configured will create a data loop in your network topology, and
that could adversely affect network performance.
30
AT-9410GB Installation Guide
Example of a Port Trunk
Figure 16 shows an example of a port trunk between an AT-9410GB and
a network server. The server is connected to the switch with four data
links. The links are connected to ports 1 through 4 on the switch.
AT-9410GB
12-Port Gigabit Managed Switch
RS232
10GbE
10/100Mbps
ACT
LINK
LINK
FDX
PWR
GBIC1
GBIC2
Figure 16 Port Trunk Example 1
You can also use port trunking to increase the bandwidth between
switches. The example in Figure 17 shows a port trunk of four data links
between two AT-9410GB Gigabit Ethernet Switches.
AT-9410GB
12-Port Gigabit Managed Switch
RS232
10GbE
10/100Mbps
ACT
PWR
LINK
LINK
FDX
GBIC1
GBIC2
AT-9410GB
12-Port Gigabit Managed Switch
RS232
10GbE
10/100Mbps
ACT
PWR
FDX
LINK
LINK
GBIC1
GBIC2
Figure 17 Port Trunk Example 2
31
Product Description
Port Security
The AT-9410GB Gigabit Ethernet Switch has three levels of port security:
Normal (default), Limited, Secure. You can use the port security levels to
enhance the security to your network. The security levels are briefly
described below. For further information and instructions on activating
a security level, refer to the AT-S45 Management Software User’s
Guide.
Normal
This is the default port security setting and indicates that port security
has been disabled.
Limited
You use this security level to manually specify the maximum number of
dynamic MAC addresses a port on the switch can learn. Once a port has
learned its maximum limit of MAC addresses, it will discard any frames
that it receives with a source MAC address not already learned and
stored in the MAC address table.
This security level can prevent unauthorized individuals from
connecting to your network and gaining access to network resources.
For example, if an AT-9410GB port is connected to an Ethernet hub with
four workstations attached, you can configure the switch port to learn
only four MAC addresses. Once those addresses are learned, any one
else attempting to connect to the network through the Ethernet hub
would be denied access.
Secure
This security level causes the switch to immediately stop learning new
dynamic MAC addresses. The switch forwards frames based on the
dynamic MAC addresses that it has already learned and any static MAC
addresses that the network administrator has entered.
32
AT-9410GB Installation Guide
A Few Basics to Ethernet Switching
An Ethernet switch interconnects network devices, such as workstations,
printers, routers, and other Ethernet switches, so that they can
communicate with each other by sending and receiving Ethernet
frames.
MAC Address
Table
Every hardware device on your network has a unique MAC address. This
address is assigned to the device by the device’s manufacturer. For
example, when you install a network interface card (NIC) in a computer
so that you can connect it to the network, the NIC already has a MAC
address assigned to it by its manufacturer.
The AT-9410GB Gigabit Ethernet Switch contains an 8 kilobyte MAC
address table. The switch uses the table to store the MAC addresses of
the network nodes connected to its ports, along with the port number
on which each address was learned.
The switch learns the MAC addresses of the end nodes by examining the
source address of each packet received on a port. It adds the address
and port on which the packet was received to the MAC table if the
address had not already been entered in the table. The result is a table
that contains all the MAC addresses of the devices that are connected to
the switch’s ports, and the port number where each address was
learned.
When the switch receives a packet, it also examines the destination
address and, by referring to its MAC address table, determines the port
on which the destination node is connected. It then forwards the packet
to the appropriate port and on to the end node. This increases network
bandwidth by limiting each packet to the appropriate port where the
intended end node is located, freeing the other switch ports for
receiving and transmitting data.
If the switch receives a packet with a destination address that is not in
the MAC address table, it floods the packet to all the ports on the switch.
If the ports have been grouped into virtual LANs, the switch floods the
packet only to those ports which belong to the same VLAN as the port
on which the packet was received. This prevents packets from being
forwarded onto inappropriate LAN segments, increasing network
security. When the destination node responds, the switch adds its MAC
address and port number to the table.
If the switch receives a packet with a destination address that is on the
same port on which the packet was received, it discards the packet
without forwarding it on to any port. Since both the source node and the
destination node for the packet are located on the same port on the
switch, there is no reason for the switch to forward the packet.
33
Product Description
Duplex Mode
Duplex mode refers to how an end node receives and transmits data. If
an end node can receive or transmit data, but not both simultaneously,
the end node is operating in what is referred to as half-duplex mode. If
an end node can both receive and transmit data simultaneously, the
node is said to be operating in full-duplex mode. Naturally, a node
capable of operating in full-duplex can handle data much faster than a
node that can only operate in half-duplex mode.
Each port on an AT-9410GB Switch can operate in either half- or fullduplex mode. The ports are IEEE 802.3u-compliant and will AutoNegotiate the duplex mode setting for you. If the end node connected
to a port on the switch is capable of full-duplex operation, the switch
sets the port to full-duplex. If the end node is capable of only halfduplex, the port is set automatically to half-duplex.
By allowing the switch to configure the duplex mode for each port itself,
you will not need to change the setting for a port on the switch should
you replace an end node with a node that has a different duplex mode
capability. With Auto-Negotiation, the switch will automatically reset the
port to a new duplex mode setting for you.
If desired, Auto-Negotiation on the switch ports can be disabled so that
you can set the duplex mode manually through the switch’s
management software.
34
Store and
Forward
This Gigabit Ethernet Switch uses store and forward as the method for
receiving and transmitting frames. When a Ethernet frame is received on
a switch port, the switch does not retransmit the frame out the
destination port until it has received the entire frame and stored the
frame in a port buffer. It then examines the frame to determine if it is a
valid frame. Invalid frames, such as fragments or runts, are discarded by
the switch. This insures that only valid frames are transmitted out the
switch ports and that damaged frames are not propagated on your
network.
Backpressure
and Flow
Control
In order for an Ethernet switch to maintain the orderly movement of
data between the end nodes that are connected to its ports, it may
periodically need to signal an end node to stop sending data. This can
occur under several circumstances. For example, if two end nodes are
operating at different speeds, the switch, while transferring data
between the nodes, might need to instruct the faster end node to stop
transmitting data to allow the slower end node to catch up. An example
of this would be when a server operating at 100 Mbps is sending data to
a workstation operating at only 10 Mbps.
AT-9410GB Installation Guide
How a switch signals an end node to stop transmitting data differs
depending on the speed and duplex mode of the end node and switch
port. A twisted pair port operating at 100 Mbps and half-duplex mode
stops an end node from transmitting data by forcing a collision. A
collision on an Ethernet network occurs when two nodes attempt to
transmit data using the same data link at the same time. A collision
causes end nodes to stop sending data. When the switch needs to stop a
100 Mbps, half-duplex end node from transmitting data, it forces a
collision on the data link, which stops the end node. Once the switch is
ready to receive data again, the switch stops forcing collisions. This is
referred to as backpressure.
A twisted pair port operating at 100 Mbps and full-duplex mode uses
PAUSE frames, as specified in the IEEE 802.3x standard, to stop the
transmission of data from an end node. Whenever the switch wants an
end node to stop transmitting data, it issues this frame. The frame
instructs the end node to cease transmission. The switch continues to
issue PAUSE frames until it is ready again to receive data from the end
node. This is referred to as flow control.
35
Product Description
Network Topologies
This section illustrates several of the network topologies you can create
with the AT-9410GB Gigabit Ethernet Switch.
Power
Workgroup
Topology
The topology shown in Figure 18 is commonly referred to as a power
workgroup topology. Each workstation or node is connected directly to
a port on an AT-9410GB Gigabit Ethernet Switch, giving each node a
dedicated data link to the switch for best performance and reliability.
The devices can operate at 10, 100, or 1000 Mbps.
LINK
AT-9410GBManaged Switch
12-Port Gigabit
RS232
LINK
10GbE
GBIC2
AT-9410GB Gigabit
Ethernet Switch
GBIC1
10/100Mbps
ACT
FDX
PWR
Legend
10 Mbps
100 Mbps
1000 Mbps
Figure 18 Power Workgroup Topology
36
AT-9410GB Installation Guide
Collapsed
Backbone Switch
Topology 1
The AT-9410GB switch can be used to create a 1000 Mbps backbone for
the other switches in your network. In the topology illustrated below,
several AT-8224XL Fast Ethernet Switches, each of which contain a
1000Base-T AT-14 uplink module, are connected to an AT-9410GB to
form a high-speed backbone between the switches.
AT-9410GB Gigabit
Ethernet Switch
LINK
AT-9410GBManaged Switch
12-Port Gigabit
RS232
LINK
10GbE
GBIC2
GBIC1
10/100Mbps
ACT
FDX
PWR
AT-8224XL Switches
with AT-14 Uplink
PORT ACTIVITY
RS-232
TERMINAL PORT
STATUS
10BASE-T / 100BASE-TX
10BASE-T / 100BASE-TX
SWITCH
FAST ETHERNET
PORT ACTIVITY
RS-232
TERMINAL PORT
STATUS
10BASE-T / 100BASE-TX
10BASE-T / 100BASE-TX
SWITCH
FAST ETHERNET
PORT ACTIVITY
RS-232
TERMINAL PORT
STATUS
10BASE-T / 100BASE-TX
10BASE-T / 100BASE-TX
SWITCH
FAST ETHERNET
PORT ACTIVITY
RS-232
TERMINAL PORT
STATUS
10BASE-T / 100BASE-TX
10BASE-T / 100BASE-TX
SWITCH
FAST ETHERNET
PORT ACTIVITY
RS-232
TERMINAL PORT
STATUS
10BASE-T / 100BASE-TX
10BASE-T / 100BASE-TX
SWITCH
FAST ETHERNET
PORT ACTIVITY
10BASE-T / 100BASE-TX
10BASE-T / 100BASE-TX
SWITCH
FAST ETHERNET
RS-232
TERMINAL PORT
STATUS
Legend
1000 MBps
Figure 19 Collapsed Backbone - Switch Topology 1
37
Product Description
Collapsed
Backbone Switch
Topology 2
If you need to connect multiple AT-9410GB switches and the switches
are physically separated by large distances, you can install fiber optic
GBIC modules. The modules can span large distances and, since they
operate a 1000 Mbps, can be used to build a fast backbone between the
switches.
One method for connecting multiple switches is with a collapsed
backbone topology, using a high-speed 1000Base-SX or 1000Base-LX
switch as the focal point of the backbone. Figure 20 illustrates a
topology that links six AT-9410GB Ethernet Switches using an AT-9006SX
Gigabit Ethernet Switch. Each AT-9410GB Gigabit Ethernet Switch has at
least one fiber optic GBIC module.
PORT ACTIVITY
3
1000BASE-SX
1000BASE-SX GIGABIT
ETHERNET SWITCH
1
2
D/C
D/C
D/C
RX
TX
D/C
RS232
LINK
10GbE
AT-9006SX Gigabit
Ethernet Switch
STATUS
FAULT
L /A
COL
PWR
RESET
TX
TX
RX
RX
RX
AT-9410GB Gigabit Ethernet Switches
LINK
LINK
12-Port Gigabit
HALF DUP
D/C
D/C
AT-9410GBManaged Switch
ACTIVITY
FULL DUP
L /A
L /A
D/C
AT-9410GB Gigabit Ethernet Switches
LINK
RPS
6
5
4
B
TX
L /A
RX
TX
RX
TX
RS-232
TERMINAL PORT
L /A
L /A
L /A
A
AT-9410GBManaged Switch
GBIC2
12-Port Gigabit
GBIC1
RS232
10/100Mbps
LINK
10GbE
GBIC2
GBIC1
10/100Mbps
ACT
ACT
FDX
FDX
PWR
PWR
LINK
LINK
AT-9410GBManaged Switch
12-Port Gigabit
RS232
10GbE
LINK
GBIC2
GBIC1
AT-9410GBManaged Switch
12-Port Gigabit
RS232
10/100Mbps
ACT
10GbE
LINK
GBIC2
GBIC1
10/100Mbps
ACT
FDX
FDX
PWR
PWR
LINK
AT-9410GBManaged Switch
12-Port Gigabit
RS232
10GbE
10/100Mbps
LINK
GBIC1
GBIC2
LINK
AT-9410GBManaged Switch
12-Port Gigabit
ACT
RS232
FDX
PWR
10GbE
LINK
10/100Mbps
ACT
FDX
PWR
Legend
1000 Mbps
Figure 20 Collapsed Backbone - Switch Topology 2
38
GBIC1
GBIC2
Chapter 2
Installation
This chapter contains the installation procedures for the switch. This
chapter contains the following sections:
G Installation Safety Precautions
G Selecting a Site for the Switch
G Required Cables
G Unpacking the Switch
G Installing the Switch on a Desktop
G Installing the Switch in a Rack
G Installing a GBIC Expansion Module
G Cabling the Switch
G Powering on the Switch
G Starting a Local Management Session
G Warranty Registration
39
Installation
Installation Safety Precautions
Please review the following safety precautions before you begin to
install the switch. Refer to Translated Electrical Safety and Emission
Information on page 65 for translated safety statements in your
language. (The laser warnings apply only if you purchased an optional
fiber optic GBIC module for the AT-9410GB switch.)
Laser
Class 1 laser product.
6
Laser
Do not stare into the laser beam.
7
Warning
Electric Shock Hazard: To prevent electric shock, do not remove
the cover. There are no user-serviceable parts inside. The unit
contains hazardous voltages and should only be opened by a
trained and qualified technician.
8
Warning
Lightning Danger: Do not work on this equipment or cables
during periods of lightening activity.
9
Warning
Power cord is used as a disconnection device: To de-energize
equipment, disconnect the power cord.
10
Warning
Electrical-Type Class 1 Equipment: This equipment must be
earthed. The power plug must be connected to a properly wired
earth ground socket outlet. An improperly wired socket outlet
could place hazardous voltages on accessible metal parts.
11
Caution
Pluggable Equipment: The socket outlet should be installed near
the equipment and should be easily accessible.
12
Caution
Air vents: The air vents must not be blocked on the unit and must
have free access to the room’s ambient air for cooling.
13
Caution
Operating Temperature: This product is designed for a maximum
ambient temperature of 40°C.
14
40
AT-9410GB Installation Guide
Caution
All Countries: Install this product in accordance with local and
national electric codes.
15
41
Installation
Selecting a Site for the Switch
Observe the following requirements when choosing a site for your
switch:
G If you plan to install the switch in an equipment rack, check to be
sure that the rack is safely secured and that it will not tip over.
Devices in a rack should be installed starting at the bottom, with
the heavier devices near the bottom of the rack.
G If you are installing the switch on a table, be sure that the table is
level and secure.
G The power outlet for the switch should be located near the unit
and should be easily accessible.
G The site should provide for easy access to the ports on the front of
the switch. This will make it easy for you to connect and
disconnect cables, as well as view the switch’s LEDs.
G To allow proper cooling of the switch, air flow around the unit and
through its vents on the side and rear should not be restricted.
G Do not place objects on top of the switch.
G Do not expose the switch to moisture or water.
G Make sure that the site is a dust-free environment.
G You should use dedicated power circuits or power conditioners to
supply reliable electrical power to the network devices.
42
AT-9410GB Installation Guide
Required Cables
Table 7 contains the specifications of the cables required for the twisted
pair ports on the AT-9410GB Gigabit Ethernet Switch.
Table 7 Media Types and Distances
Speed
Category
Maximum Distance
10 Mbps
Category 3 or better
100-ohm shielded or
unshielded, straightthrough or crossover
twisted pair cable
100 m (328 ft.)
100 Mbps
Category 5 or
Category 5E
(Enhanced) 100-ohm
shielded or
unshielded, straightthrough or crossover
twisted pair cable
100 m (328 ft.)
1000 Mbps
Category 5 and
Category 5E
(Enhanced) 100-ohm
shielded or
unshielded, straightthrough twisted pair
cable
100 m (328 ft.)
Note
The ports on the AT-9410GB switch are IEEE 802.3ab-compatible
and are configured automatically by the switch as MDI or MDI-X
when connected to a 10 Mbps or 100 Mbps end node. This allows
you to use either a straight-through or cross-over cable.
Note
For cabling specifications for an optional GBIC module, refer to the
GBIC Installation Guide included with the module.
43
Installation
Unpacking the Switch
To unpack the switch, perform the following procedure:
1. Remove all components from the shipping package and store the
packaging material in a safe location.
Note
You must use the original shipping material if you need to return
the unit to Allied Telesyn.
2. Place the switch on a level, secure surface.
3. Make sure the following hardware components are included in your
switch package. If any item is missing or damaged, contact your Allied
Telesyn sales representative for assistance.
G One AT-9410GB Gigabit Ethernet Switch
G Two mounting brackets
G Eight Phillips-head screws
G Four rubber feet
G Power cord (Americas, EC, Australia, and UK only)
G Null modem management cable
G Documentation CD
G Warranty and registration card
G Two extra serial number stickers
G Two extra MAC address labels
44
AT-9410GB Installation Guide
Installing the Switch on a Desktop
Perform the following procedure to install the switch on a desktop or
table. If you would prefer to install the switch in a rack, go to the next
procedure:
1. Place the unit upside down on a level, secure surface.
2. Remove the adhesive tabs from the stick-on rubber feet and apply
one tab to each corner of the bottom of the switch.
3. Turn the switch over.
45
Installation
Installing the Switch in a Rack
Perform the following procedure to install the switch in a standard 19inch rack. If you are not installing the switch in a rack, go to the next
procedure:
1. Attach a rack-mounting bracket to one side of the switch using four
of the screws that came with the switch. See Figure 21.
Figure 21 Attaching Rackmounting Brackets
2. Install the second rackmounting bracket on the other side of the
switch using the four remaining screws.
46
AT-9410GB Installation Guide
3. Mount the switch in a19-inch rack using standard screws (not
provided), as shown in Figure 22.
RS23
2
PWR
GBIC2
Figure 22 Attaching Rackmounting Brackets
47
Installation
Installing an Optional GBIC Module
If you purchased an optional GBIC module, perform the following
procedure. If you did not purchase an optional module, go to the next
procedure.
1. Unpack the GBIC module from its shipping container and store the
packaging material in a safe location.
Note
You must use the original shipping material if you need to return
the module to Allied Telesyn.
Warning
A GBIC module can be damaged by static electricity. Be sure to
observe all standard electrostatic discharge (ESD) precautions, such
as wearing an antistatic wrist strap, to avoid damaging the module.
2. Check that the GBIC package includes all the items listed below. If any
item is missing or damaged, contact your Allied Telesyn sales
representative for assistance.
G One GBIC module
G Installation Guide
G Warranty card
48
AT-9410GB Installation Guide
3. Slide the GBIC module into one of the expansion slots in the front of
the AT-9410GB Switch. The GBIC module is completely seated in the
slot when it clicks into place.
LIN
K
GBI
C1
LIN
K
Figure 23 Installing a GBIC Module
Note
If you are installing only one GIBC module in the switch, you should
install the module in the slot labeled GBIC1. While the module will
work in the GBIC2 slot with the GBIC1 slot empty, the port
numbering assignments will change if you later install a module in
the GBIC1 slot. This could affect the VLAN memberships on the
switch and that could require adjusting your VLAN configurations.
For example, if you install a GBIC in the GBIC2 slot with the GBIC1
slot empty, the switch will assign port number 11 to the GBIC in the
GBIC2 slot. If you later install a GBIC in the GBIC1 slot, the switch will
reallocate port number 11 to the new module in the GBIC1 slot and
assign port number 12 to the module in the GBIC2 slot. If the
module in the GBIC2 slot was a member of a VLAN other than the
Default VLAN, you would have to reconfigure the switch’s VLANs to
reflect the change to the module’s port number.
4. If you purchased two GBIC modules for the switch, repeat this
procedure to install the second module.
49
Installation
Cabling the Switch
Perform the following procedure to connect the data cables to the
switch ports. Refer to Required Cables on page 43 for cable
specifications.
1. Connect the twisted pair cables to the RJ-45 ports on the switch, as
shown in Figure 24.
AT-
12-P 9410
ort G GB
igab
it Ma
n
aged
RS2
PW
R
Swit
32
ch
10G
b
00M E
bps
10/1
ACT
FDX
Figure 24 Connecting the Twisted Pair Cables
When connecting a twisted pair cable to a port on the switch,
observe the following guidelines:
G An RJ-45 connector should fit snugly into the port on the switch.
The tab on the connector should lock the connector into place.
G Do not connect a port on the switch to a phone jack. Doing so can
damage the switch.
G Since the RJ-45 ports on the switch are auto-MDI/MDI-X, you can
use either straight-through or cross-over twisted pair cables to
connect 10/100 Mbps devices to the switch. To connect a 1000
Mbps device to the switch, use a straight-through cable. A crossover cable will not work when connected to a 1000 Mbps device.
G If your network topology will contain a loop where two or more
network devices can communicate with each other over more
than one data path, do not connect the network cables forming
the loop until after you have activated the Spanning Tree Protocol
(STP) on the switch. Data loops can adversely affect network
performance. For instructions on how to activate STP, refer to the
AT-S45 Management Software User’s Guide.
50
AT-9410GB Installation Guide
G If you are creating a port trunk, do not connect the cables of the
trunk to the switch until after you have configured the trunk using
the switch’s management software. Connecting the trunk cables
to the switch before you have configured the software will result
in a data loop, which can adversely affect network performance.
For instructions on how to configure a port trunk, refer to the ATS45 Management Software User’s Guide.
2. If you installed an optional GBIC module, remove the dust cover from
the GBIC port. Store the dust cover in a safe place so that you can use
it to protect the port if you disconnect the fiber cable.
LIN
K
GBI
C1
LIN
K
GB
Figure 25 Removing the Dust Cover from a GBIC Module
Caution
Do not remove the dust cover if you do not intend to connect the
fiber optic cable at this time. Dust contamination can adversely
impact the operations of the port.
51
Installation
3. Attach the fiber optic data cable to the port on the GBIC module.
LIN
K
GBI
C1
LIN
K
GBI
C2
Figure 26 Attaching a Fiber Optic Cable to a GBIC Module
When you attach a fiber optic cable to a GBIC module, be sure to
observe the following guidelines:
G You should verify that you are using the appropriate type of fiber
optic cabling. For GBIC cabling specifications, refer to the GBIC
Installation Guide.
G You should verify that the operating specifications of the remote
fiber optic port are compatible with the GBIC module. For
example, you cannot connect a fiber optic GBIC module with a
maximum distance of 40 kilometers and an operating wavelength
of 1550 nanometers (nm) to a remote fiber optic port with an
maximum distance of only 10 kilometers and an operating
wavelength of 1310 nm.
G Be sure that the cable connector is firmly locked into place in the
port.
G If the GBIC module has a dual SC connector, be sure to connect the
receiver fiber port on the module to the transmitter port on the
remote end node, and the transmitter fiber port on the GBIC
module to the receiver port on the remote node.
52
AT-9410GB Installation Guide
Powering On the Switch
1. Apply AC power to the switch by plugging the power cord into the AC
power connector on the back panel of the unit and plugging the
other end into a wall outlet.
Warning
The power cord is used as a disconnection device. To de-energize
equipment, disconnect the power cord.
10
As power is applied to the switch, the amber system PWR LED
(shown in Figure 27) lights up as the switch loads its operating
software. This process takes only a minute or two. After the switch
has finished loadings its software, the PWR LED will turn green
and remain ON.
AT-9410GB
12-Port Gigabit Managed Switch
RS232
10GbE
10/100Mbps
ACT
Power LED
PWR
FDX
Figure 27 Power LED
Note
Refer to the section System LED on page 18 for information on the
PWR LED.
The switch is ready for network operations.
Note
If you do not need to change the default parameter settings of the
switch, no further installation steps are required. For the default
settings, refer to the AT-S45 Management Software User’s
Guide.
53
Starting a Local Management Session
The procedure in this section explains how to start a local (out-of-band)
management session by cabling the RS-232 Terminal Port on the front
panel of the switch and setting the appropriate terminal values. You can
use a local management session to configure the switch’s operating
parameters and view performance and error statistics.
To start a local management session, perform the following procedure:
1. Connect one end of the null modem management cable to the RS232 Terminal Port on the front panel of the switch, as shown in Figure
28.
AT-
12-P 9410
ort G GB
igab
it Ma
n
aged
RS2
PW
R
Swit
32
ch
10G
b
00M E
bps
10/1
ACT
FDX
Figure 28 Connecting the Null Modem Management Cable to the RS232 Terminal Port
2. Connect the other end of the cable to an RS-232 port on a terminal or
a personal computer with a terminal emulation program.
AT-9410GB Installation Guide
3. Set the terminal or the terminal emulation program to the following
settings:
G Emulation mode: VT100
G Baud rate: 9600
G Data bits: 8
G Parity: None
G Stop bits: 1
G Flow control: None
G Key mode: Terminal keys
Note
These are the default settings for the RS-232 Terminal Port. They are
for a DEC VT100 or ANSI terminal or an equivalent terminal
emulation program.
When the terminal session starts, it displays the management software’s
login prompt, shown in Figure 29. Enter the login name and password.
The default login name and password are both “manager.” For
instructions on how to change the password, refer to the AT-S45
Management Software User’s Guide.
AT-9410GB Management System Version 1.00E
Local - Console
Allied Telesyn International Corp.
Copyright, 2001
==================================================
Login Menu
Login: manager
Password: _
Figure 29 AT-S45 Login Prompt - Local Management Session
55
Installation
The switch then displays the management software’s Main Menu, shown
in Figure 30.
AT-9410GB Local Management System
Main Menu
[G]eneral Information
[B]asic Switch Configuration...
[A]dvanced Switch Configuration...
Switch [T]ools...
[S]tatistics
[Q]uit
Command>
Enter the character in square brackets to select option
Figure 30 AT-S45 Main Menu - Local Management Session
You can now manage the switch using the management
interface. For instructions, refer to the AT-S45 Management
Software User’s Guide. This guide is available from the Allied
Telesyn web site at www.alliedtelesyn.com.
56
AT-9410GB Installation Guide
Warranty Registration
When you have finished installing the switch, register your product by
completing the enclosed warranty card and sending it in or by visiting
our web site and completing the on-line registration form.
57
Chapter 3
Troubleshooting
This chapter contains information on how to troubleshoot the switch in
the event a problem occurs.
Note
If after following the instructions in this chapter you are unable to
resolve the problem, contact Allied Telesyn Technical Support for
assistance. Refer to Contacting Allied Telesyn on page 9 for
information on how to contact our Technical Support Department.
Check the PWR LED on the front of the switch. If the LED is OFF,
indicating that the unit is not receiving power, do the following:
G Make sure that the power cord is securely connected to the power
source and to the AC connector on the back panel of the switch.
G Verify that the power outlet has power by connecting another
device to it.
G Try connecting the unit to another power source.
G Try using a different power cord.
G Check that the voltage from the power source is within the
required levels for your region.
Verify that the ACT LED for each twisted pair port is ON. If a Link LED is
OFF, do the following:
G Verify that the end node connected to the port is powered ON and
is operating properly.
58
AT-9410GB Installation Guide
G Check that the twisted pair cable is securely connected to the port
on the switch and to the port on the end node.
G Make sure that the twisted pair cable does not exceed 100 meters
(328 feet).
G Verify that you are using the appropriate category of twisted pair
cable: Category 3 or better for 10 Mbps operation, Category 5 and
Category 5E for 100/1000 Mbps operation.
G Make sure that the operating parameters of the port on the switch
are compatible with the end node to which the port is connected.
This will require using the switch’s management software. For
instructions, refer to the AT-S45 Management Software User’s
Guide.
If you installed an optional GBIC module, verify that the LED for the port
is ON. If the LED is OFF, do the following:
G Check to make sure that the GBIC module is completely seated in
the GBIC slot. It should click into place.
G Verify that the end node connected to the port is powered ON and
is operating properly.
G Check that the fiber optic cable is securely connected to the port
on the switch and to the port on the end node.
G Make sure that the cable connected to the fiber optic receiver port
on the GBIC module is connected to the transmitter port on the
remote end node and that the fiber optic transmitter port on the
GBIC module is connected to the receiver port on the end node.
The GBIC port LINK LED will be illuminated when the Tx and Rx
ports are connected properly. If the LINK LED is not illuminated,
reverse the cables. Refer to GBIC Port LEDs on page 20 for more
information.
G Make sure that the fiber optic cable does not exceed the allowed
maximum distance. For GBIC maximum distances, refer to the
GBIC Installation Guide.
G Verify that you are using the appropriate type of fiber optic cable.
For cable specifications, refer to the GBIC Installation Guide.
G Use a fiber optic tester to test the attenuation on the cable to
determine if the strength of the fiber optic signal falls below
59
Troubleshooting
acceptable limits. For specifications on the transceiver in the GBIC
module, refer to the GBIC Installation Guide.
G Check that the operating specifications (for instance, wavelength
and maximum operating distance) of the fiber optic port on the
remote end node are compatible with the fiber optic port on the
GBIC module. For example, you cannot connect a GBIC module
with a maximum distance of 40 kilometers and a wavelength of
1550 nanometers (nm) to a remote fiber optic port with an
maximum distance of only 10 kilometers and a wavelength of
1310 nm.
G Verify that the remote fiber optic port is operating at 1000 Mbps
and in full-duplex mode. The 1000 Mbps operating speed of the
GBIC module is fixed and cannot be changed.
If you are unable to establish a local management session with the
switch through the RS-232 Terminal Port on the front panel, do the
following:
G Check to be sure that the RS-232 cable is securely connected to
the RS-232 Terminal Port on the switch and to the RS-232 port on
the terminal or personal computer.
G Check to be sure that you are using the null modem management
cable.
G Check to be sure that the operating parameters on the terminal or
the terminal emulation program, if you are using a personal
computer, have been set correctly. The default settings for the
RS232 Terminal Port can be found in Starting a Local
Management Session on page 54.
60
Appendix A
Technical Specifications
Physical Specifications
Dimensions
Weight
Recommended Minimum Ventilation on All Sides
44 cm x 25.3 cm x 4.32 cm (W x D x
H)
(17.32 in. x 9.96 in. x 1.7 in.)
3.98 kg (8.77 lbs)
5.08 cm (2.0 in.)
Environmental Specifications
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Operating Altitude Range
Storage Altitude Range
0° C to 40° C (32° F to 104° F)
-20° C to 70° C (-4° F to 158° F)
10% to 90% non-condensing
10% to 95% non-condensing
Up to 3,000 m (9,843 ft)
Up to 4,570 m (15,000 ft)
Power Specifications
Maximum Power Consumption
AC Input Voltage
Frequency
61
60 Watts
100-240 VAC
50-60 Hz
Technical Specifications
Safety and Electromagnetic Emissions Certifications
Safety
EMI
Immunity
Quality and Reliability
Standards
IEEE 802.3 (10Base-T Ethernet)
IEEE 802.3u (100Base-TX Ethernet)
IEEE 802.3z (1000Base-X Gigabit Ethernet)
IEEE 802.3ab (1000Base-T Twisted Pair Gigabit Ethernet)
IEEE 802.3ad (Link Aggregation)
IEEE 802.1d (Spanning Tree)
IEEE 802.1p (Class of Service)
IEEE 802.1q (Virtual LAN tagging)
IEEE 802.3x (Flow Control)
RFC 1112 (IGMP Snooping Version 1.0)
RFC 2236 (IGMP Snooping Version 2.0)
SNMP Support
RFC 1213 (MIB II)
RFC 1493 (Bridge MIB)
RFC 1757 (4-Group RMON)
Allied Telesyn Enterprise MIB
62
UL 1950 (UL/cUL), EN60950
FCC Class A, EN55022, CE Class A,
CISPR22 Class A (VCCI), AS/NZS3548
(C-TICK), EN61000-3-2, EN61000-3-3
EN55024
MTBF > 65,403 hrs, MTTR < 1 hr,
DOA < 0.5%
Appendix B
Default Switch Settings
This appendix lists factory default settings for the switch.
Setting
Default
IP Address
Subnet Mask
Gateway Address
DHCP
IGMP Snooping
System Name
MAC Aging Time
Spanning Tree Protocol
Status
Bridge Priority
Bridge Max Age Time
Bridge Hello Time
Bridge Forwarding Delay
Twisted Pair Ports
Status
Speed/Duplex Mode
Flow Control
Broadcast Storm Control
MDI/MDI-X
Security
Port Mirroring
Port Trunking
0.0.0.0
0.0.0.0
0.0.0.0
Disabled
Disabled
None
300 seconds
Disabled
32768
20
2
15
Enabled
Auto-Negotiate
Auto
Disabled
Auto
Normal
Disabled
Disabled
63
Default Switch Settings
Setting
VLANs
Port-based and Tagged VLANs
VLAN Name
Default VLAN ID
RS-232 Terminal Port
Emulation Mode
Data Bits
Stop Bits
Parity
Flow Control
Data Rate
Key Mode
Software Management Access
Login Name
Login Password
64
Default
Enabled
Default VLAN (all ports)
1
VT100
8
1
None
None
9600 bps
Terminal (not Windows)
manager
manager
Appendix C
Translated Electrical Safety and
Emission Information
Important: This appendix contains multiple-language translations for
the safety statements in this guide.
Wichtig: Dieser Anhang enthält Übersetzungen der in diesem
Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen.
Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af
sikkerhedsadvarslerne i denne håndbog.
Belangrijk: Deze appendix bevat vertalingen in meerdere talen van de
veiligheidsopmerkingen in deze gids.
Important: Cette annexe contient la traduction en plusieurs langues des
instructions de sécurité figurant dans ce guide.
Tärkeää: Tämä liite sisältää tässä oppaassa esiintyvät turvaohjeet usealla
kielellä.
Importante: questa appendice contiene traduzioni in più lingue degli
avvisi di sicurezza di questa guida.
Viktig: Dette tillegget inneholder oversettelser til flere språk av
sikkerhetsinformasjonen i denne veiledningen.
Importante: Este anexo contém traduções em vários idiomas das
advertências de segurança neste guia.
Importante: Este apéndice contiene traducciones en múltiples idiomas
de los mensajes de seguridad incluidos en esta guía.
Obs! Denna bilaga innehåller flerspråkiga översättningar av
säkerhetsmeddelandena i denna handledning.
65
Translated Electrical Safety and Emission Information
Standards: This product meets the following safety standards.
U.S. Federal Communications Commission
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with this instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
Note: Modifications or changes not expressly approved by the manufacturer or
the FCC can void your right to operate this equipment.
Canadian Department of Communications
This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
66
1
RFI Emission
FCC Class A, EN55022 Class A,
CISPR22 Class A (VCCI), AS/NZS3548
(C-TICK), EN61000-3-2, EN61000-3-3
2
WARNING: In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
3
Immunity
EN55024
4
Electrical Safety
UL 1950 (UL/cUL), EN60950
5
Laser
EN60825
SAFETY
6
WARNING: Class 1 Laser product.
7
WARNING: Do not stare into the laser beam.
8
ELECTRICAL NOTICES
WARNING: ELECTRIC SHOCK HAZARD
To prevent ELECTRIC shock , do not remove the cover. No user-serviceable parts
inside. This unit contains HAZARDOUS VOLTAGES and should only be opened by a
trained and qualified technician. To avoid the possibility of ELECTRIC SHOCK,
disconnect electric power to the product before connecting or disconnecting the
LAN cables.
9
LIGHTNING DANGER
DANGER: DO NOT WORK on equipment or CABLES during periods of LIGHTNING
ACTIVITY.
10
CAUTION: POWER CORD IS USED AS A DISCONNECTION DEVICE. TO DE-ENERGIZE
EQUIPMENT, disconnect the power cord.
11
ELECTRICAL - TYPE CLASS 1 EQUIPMENT
THIS EQUIPMENT MUST BE EARTHED. Power plug must be connected to a properly
wired earth ground socket outlet. An improperly wired socket outlet could place
hazardous voltages on accessible metal parts.
AT-9410GB Installation Guide
12
PLUGGABLE EQUIPMENT, the socket outlet shall be installed near the equipment and
shall be easily accessible.
13
CAUTION: Air vents must not be blocked and must have free access to the room
ambient air for cooling.
14
OPERATING TEMPERATURE: This product is designed for a maximum ambient
temperature of 40° degrees C.
15
ALL COUNTRIES: Install product in accordance with local and National Electrical
Codes.
67
Translated Electrical Safety and Emission Information
68
Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen.
1
Hochfrequenzstörung
FCC Klasse A, EN55022 Klasse A,
CISPR22 Class A (VCCI), AS/NZS3548
(C-TICK), EN61000-3-2, EN61000-3-3
2
WARNUNG: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen
hervorrufen. In diesem Fall müßte der Anwender angemessene Gegenmaßnahmen
ergreifen.
3
Störsicherheit
EN55024
4
Elektrische Sicherheit
UL 1950 (UL/cUL), EN60950
5
Laser
EN60825
SICHERHEIT
6
WARNUNG Laserprodukt der Klasse 1.
7
WARNUNG Nicht direkt in den Strahl blicken.
8
ACHTUNG: GEFÄHRLICHE SPANNUNG
Das Gehäuse nicht öffnen. Das Gerät enthält keine vom Benutzer wartbaren Teile.
Das Gerät steht unter Hochspannung und darf nur von qualifiziertem technischem
Personal geöffnet werden. Vor Anschluß der LAN-Kabel, Gerät vom Netz trennen.
9
GEFAHR DURCH BLITZSCHLAG
GEFAHR: Keine Arbeiten am Gerät oder an den Kabeln während eines Gewitters
ausführen.
10
VORSICHT: DAS NETZKABEL DIENT ZUM TRENNEN DER STROMVERSORGUNG. ZUR
TRENNUNG VOM NETZ, KABEL AUS DER STECKDOSE ZIEHEN.
11
GERÄTE DER KLASSE 1
DIESE GERÄTE MÜSSEN GEERDET SEIN. Der Netzstecker darf nur mit einer
vorschriftsmäßig geerdeten Steckdose verbunden werden. Ein unvorschriftsmäßiger
Anschluß kann die Metallteile des Gehauses unter gefährliche elektrische
Spannungen setzen.
12
STECKBARES GERÄT: Die Anschlußbuchse sollte in der Nähe der Einrichtung
angebracht werden und leicht zugänglich sein."
13
VORSICHT
Die Entlüftungsöffnungen dürfen nicht versperrt sein und müssen zum Kühlen freien
Zugang zur Raumluft haben.
14
BETRIEBSTEMPERATUR: Dieses Produkt wurde für den Betrieb in einer
Umgebungstemperatur von nicht mehr als 40° C entworfen.
15
ALLE LÄNDER: Installation muß örtlichen und nationalen elektrischen Vorschriften
entsprechen.
AT-9410GB Installation Guide
Standarder: Dette produkt tilfredsstiller de følgende standarder.
1
Radiofrekvens forstyrrelsesemission
FCC Klasse A, EN55022 Klasse A,
CISPR22 Class A (VCCI), AS/NZS3548
(C-TICK), EN61000-3-2, EN61000-3-3
2
ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse.
Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige
foranstaltninger.
3
Immunitet
EN55024
4
Elektrisk sikkerhed
UL 1950 (UL/cUL), EN60950
5
Laser
EN60825
SIKKERHED
6
ADVARSEL Laserprodukt av klasse 1.
7
ADVARSEL Stirr ikke på strålen.
8
ELEKTRISKE FORHOLDSREGLER
ADVARSEL: RISIKO FOR ELEKTRISK STØD
For at forebygge ELEKTRISK stød, undlad at åbne apparatet. Der er ingen indre dele,
der kan repareres af brugeren. Denne enhed indeholder LIVSFARLIGE
STRØMSPÆNDINGER og bør kun åbnes af en uddannet og kvalificeret tekniker. For
at undgå risiko for ELEKTRISK STØD, afbrydes den elektriske strøm til produktet, før
LAN-kablerne monteres eller afmonteres.
9
FARE UNDER UVEJR
FARE: UNDLAD at arbejde på udstyr eller KABLER i perioder med LYNAKTIVITET.
10
ADVARSEL: DEN STRØMFØRENDE LEDNING BRUGES TIL AT AFBRYDE STRØMMEN.
SKAL STRØMMEN TIL APPARATET AFBRYDES, tages ledningen ud af stikket.
11
ELEKTRISK - KLASSE 1-UDSTYR
DETTE UDSTYR KRÆVER JORDFORBINDELSE. Stikket skal være forbundet med en
korrekt installeret jordforbunden stikkontakt. En ukorrekt installeret stikkontakt kan
sætte livsfarlig spænding til tilgængelige metaldele.
12
UDSTYR TIL STIKKONTAKT, stikkontakten bør installeres nær ved udstyret og skal
være lettilgængelig.
13
ADVARSEL: Ventilationsåbninger må ikke blokeres og skal have fri adgang til den
omgivende luft i rummet for afkøling.
14
BETJENINGSTEMPERATUR: Dette apparat er konstrueret til en omgivende
temperatur på maksimum 40 grader C.
15
ALLE LANDE: Installation af produktet skal ske i overensstemmelse med lokal og
national lovgivning for elektriske installationer.
69
Translated Electrical Safety and Emission Information
70
Eisen: Dit product voldoet aan de volgende eisen.
1
RFI Emissie
FCC Klasse A, EN55022 Klasse A,
CISPR22 Class A (VCCI), AS/NZS3548
(C-TICK), EN61000-3-2, EN61000-3-3
2
WAARSCHUWING: Binnenshuis kan dit product radiostoring veroorzaken, in welk
geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen.
3
Immuniteit
EN55024
4
Electrische Veiligheid
UL 1950 (UL/cUL), EN60950
5
Laser
EN60825
VEILIGHEID
6
WAARSHUWING Klasse-1 laser produkt.
7
WAARCHUWING Neit in de straal staren.
8
WAARSCHUWINGEN MET BETREKKING TOT ELEKTRICITEIT
WAARSCHUWING: GEVAAR VOOR ELEKTRISCHE SCHOKKEN
Verwijder het deksel niet, teneinde ELEKTRISCHE schokken te voorkomen. Binnenin
bevinden zich geen onderdelen die door de gebruiker onderhouden kunnen
worden. Dit toestel staat onder GEVAARLIJKE SPANNING en mag alleen worden
geopend door een daartoe opgeleide en bevoegde technicus. Om het gevaar op
ELEKTRISCHE SCHOKKEN te vermijden, moet u het toestel van de stroombron
ontkoppelen alvorens de LAN-kabels te koppelen of ontkoppelen.
9
GEVAAR VOOR BLIKSEMINSLAG
GEVAAR: NIET aan toestellen of KABELS WERKEN bij BLIKSEM.
10
WAARSCHUWING: HET TOESTEL WORDT UITGESCHAKELD DOOR DE
STROOMKABEL TE ONTKOPPELEN.OM HET TOESTEL STROOMLOOS TE MAKEN: de
stroomkabel ontkoppelen.
11
ELEKTRISCHE TOESTELLEN VAN KLASSE 1
DIT TOESTEL MOET GEAARD WORDEN. De stekker moet aangesloten zijn op een juist
geaarde contactdoos. Een onjuist geaarde contactdoos kan de metalen onderdelen
waarmee de gebruiker eventueel in aanraking komt onder gevaarlijke spanning
stellen.
12
AAN TE SLUITEN APPARATUUR, de contactdoos wordt in de nabijheid van de
apparatuur geïnstalleerd en is gemakkelijk te bereiken."
13
OPGELET: De ventilatiegaten mogen niet worden gesperd en moeten de
omgevingslucht ongehinderd toelaten voor afkoeling.
14
BEDRIJFSTEMPERATUUR: De omgevingstemperatuur voor dit produkt mag niet
meer bedragen dan 40 graden Celsius.
15
ALLE LANDEN: het toestel installeren overeenkomstig de lokale en nationale
elektrische voorschriften.
AT-9410GB Installation Guide
Normes: ce produit est conforme aux normes de suivantes:
1
Emission d’interférences radioélectriques
FCC Classe A, EN55022 Classe A,
CISPR22 Class A (VCCI), AS/NZS3548
(C-TICK), EN61000-3-2, EN61000-3-3
2
MISE EN GARDE : dans un environnement domestique, ce produit peut provoquer
des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les
mesures adéquates.
3
Immunité
EN55024
4
Sécurité électrique
UL 1950 (UL/cUL), EN60950
5
Laser
EN60825
SÉCURITÉ
6
ATTENTION Producit laser di classe 1.
7
ATTENTION Ne pas fixer le faisceau des yeux.
8
INFORMATION SUR LES RISQUES ÉLECTRIQUES
AVERTISSEMENT: DANGER D’ÉLECTROCUTION
Pour éviter toute ÉLECTROCUTION, ne pas ôter le revêtement protecteur du matériel.
Ce matériel ne contient aucun élément réparable par l’utilisateur. Il comprend des
TENSIONS DANGEREUSES et ne doit être ouvert que par un technicien dûment
qualifié. Pour éviter tout risque d’ÉLECTROCUTION, débrancher le matériel avant de
connecter ou de déconnecter les câbles LAN.
9
DANGER DE FOUDRE
DANGER: NE PAS MANIER le matériel ou les CÂBLES lors d’activité orageuse.
10
ATTENTION: LE CORDON D’ALIMENTATION SERT DE MISE HORS CIRCUIT. POUR
COUPER L’ALIMENTATION DU MATÉRIEL, débrancher le cordon.
11
ÉQUIPEMENT DE CLASSE 1 ÉLECTRIQUE
CE MATÉRIEL DOIT ÊTRE MIS A LA TERRE. La prise de courant doit être branchée dans
une prise femelle correctement mise à la terre car des tensions dangereuses
risqueraient d’atteindre les pièces métalliques accessibles à l’utilisateur.
12
EQUIPEMENT POUR BRANCHEMENT ELECTRIQUE, la prise de sortie doit être placée
près de l’équipement et facilement accessible".
13
ATTENTION: Ne pas bloquer les fentes d’aération, ceci empêcherait l’air ambiant de
circuler librement pour le refroidissement.
14
TEMPÉRATURE DE FONCTIONNEMENT: Ce matériel est capable de tolérer une
température ambiante maximum de ou 40 degrés Celsius.
15
POUR TOUS PAYS: Installer le matériel conformément aux normes électriques
nationales et locales.
71
Translated Electrical Safety and Emission Information
72
Standardit: Tämä tuote on seuraavien standardien mukainen.
1
Radioaaltojen häirintä
FCC Luokka A, EN55022 Luokka A,
CISPR22 Class A (VCCI), AS/NZS3548
(C-TICK), EN61000-3-2, EN61000-3-3
2
VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä
tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin
toimenpiteisiin.
3
Kestävyys
EN55024
4
Sähköturvallisuus
UL 1950 (UL/cUL), EN60950
5
Laser
EN60825
TURVALLISUUS
6
VAROITUS Luokan 1 Lasertuote.
7
VARIOTUS Älä katso säteeseen.
8
SÄHKÖÖN LIITTYVIÄ HUOMAUTUKSIA
VAROITUS: SÄHKÖISKUVAARA
Estääksesi SÄHKÖISKUN älä poista kantta. Sisällä ei ole käyttäjän huollettavissa olevia
osia. Tämä laite sisältää VAARALLISIA JÄNNITTEITÄ ja sen voi avata vain koulutettu ja
pätevä teknikko. Välttääksesi SÄHKÖISKUN mahdollisuuden katkaise sähkövirta
tuotteeseen ennen kuin liität tai irrotat paikallisverkon (LAN) kaapelit.
9
SALAMANISKUVAARA
HENGENVAARA: ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN KANSSA
SALAMOINNIN AIKANA.
10
HUOMAUTUS: VIRTAJOHTOA KÄYTETÄÄN VIRRANKATKAISULAITTEENA. VIRTA
KATKAISTAAN irrottamalla virtajohto.
11
SÄHKÖ - TYYPPILUOKAN 1 LAITTEET
TÄMÄ LAITE TÄYTYY MAADOITTAA. Pistoke täytyy liittää kunnollisesti
maadoitettuun pistorasiaan. Virheellisesti johdotettu pistorasia voi altistaa
metalliosat vaarallisille jännitteille.
12
PISTORASIAAN KYTKETTÄVÄ LAITE; pistorasia on asennettava laitteen lähelle ja
siihen on oltava esteetön pääsy."
13
HUOMAUTUS: Ilmavaihtoreikiä ei pidä tukkia ja niillä täytyy olla vapaa yhteys
ympäröivään huoneilmaan, jotta ilmanvaihto tapahtuisi.
14
KÄYTTÖLÄMPÖTILA: Tämä tuote on suunniteltu ympäröivän ilman
maksimilämpötilalle 40°C.
15
KAIKKI MAAT: Asenna tuote paikallisten ja kansallisten
sähköturvallisuusmääräysten mukaisesti.
AT-9410GB Installation Guide
Standard: Questo prodotto è conforme ai seguenti standard.
1
Emissione RFI (interferenza di radiofrequenza)
FCC Classe A, EN55022 Classe A,
CISPR22 Class A (VCCI), AS/
NZS3548 (C-TICK), EN61000-3-2,
EN61000-3-3
2
AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio
interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati
provvedimenti.
3
Immunità
EN55024
4
Sicurezza elettrica
UL 1950 (UL/cUL), EN60950
5
Laser
EN60825
NORME DI SICUREZZA
6
AVVERTENZA Prodotto laser di Classe 1.
7
AVERTENZA Non fissare il raggio con gli occhi.
8
AVVERTENZE ELETTRICHE
ATTENZIONE: PERICOLO DI SCOSSE ELETTRICHE
Per evitare SCOSSE ELETTRICHE non asportare il coperchio. Le componenti interne
non sono riparabili dall’utente. Questa unità ha TENSIONI PERICOLOSE e va aperta
solamente da un tecnico specializzato e qualificato. Per evitare ogni possibilità di
SCOSSE ELETTRICHE, interrompere l’alimentazione del dispositivo prima di collegare
o staccare i cavi LAN.
9
PERICOLO DI FULMINI
PERICOLO: NON LAVORARE sul dispositivo o sui CAVI durante PRECIPITAZIONI
TEMPORALESCHE.
10
ATTENZIONE: IL CAVO DI ALIMENTAZIONE È USATO COME DISPOSITIVO DI
DISATTIVAZIONE. PER TOGLIERE LA CORRENTE AL DISPOSITIVO staccare il cavo di
alimentazione.
11
ELETTRICITÀ - DISPOSITIVI DI CLASSE 1
QUESTO DISPOSITIVO DEVE AVERE LA MESSA A TERRA. La spina deve essere inserita
in una presa di corrente specificamente dotata di messa a terra. Una presa non
cablata in maniera corretta rischia di scaricare una tensione pericolosa su parti
metalliche accessibili.
12
APPARECCHIATURA COLLEGABILE, la presa va installata vicino all’apparecchio per
risultare facilmente accessibile".
13
ATTENZIONE: le prese d’aria non vanno ostruite e devono consentire il libero
ricircolo dell’aria ambiente per il raffreddamento.
14
TEMPERATURA DI FUNZIONAMENTO: Questo prodotto è concepito per una
temperatura ambientale massima di 40 gradi centigradi.
15
TUTTI I PAESI: installare il prodotto in conformità delle vigenti normative elettriche
nazionali.
73
Translated Electrical Safety and Emission Information
74
Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer.
1
RFI stråling
FCC Klasse A, EN55022 Klasse A,
CISPR22 Class A (VCCI), AS/NZS3548
(C-TICK), EN61000-3-2, EN61000-3-3
2
ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake
radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler.
3
Immunitet
EN55024
4
Elektrisk sikkerhet
UL 1950 (UL/cUL), EN60950
5
Laser
EN60825
SIKKERHET
6
ADVARSEL Laserprodukt av klasse 1.
7
ADVARSAL Stirr ikke på strålen.
8
ELEKTRISITET
ADVARSEL: FARE FOR ELEKTRISK SJOKK
For å unngå ELEKTRISK sjokk, må dekslet ikke tas av. Det finnes ingen deler som
brukeren kan reparere på innsiden. Denne enheten inneholder FARLIGE
SPENNINGER, og må kun åpnes av en faglig kvalifisert tekniker. For å unngå
ELEKTRISK SJOKK må den elektriske strømmen til produktet være avslått før LANkablene til- eller frakobles.
9
FARE FOR LYNNEDSLAG
FARE: ARBEID IKKE på utstyr eller KABLER i TORDENVÆR.
10
FORSIKTIG: STRØMLEDNINGEN BRUKES TIL Å FRAKOBLE UTSTYRET. FOR Å
DEAKTIVISERE UTSTYRET, må strømforsyningen kobles fra.
11
ELEKTRISK - TYPE 1- KLASSE UTSTYR
DETTE UTSTYRET MÅ JORDES. Strømkontakten må være tilkoplet en korrekt jordet
kontakt. En kontakt som ikke er korrekt jordet kan føre til farlig spenninger i lett t
ilgjengelige metalldeler.
12
UTSTYR FOR STIKKONTAKT. Stikkontakten skal monteres i nærheten av utstyret og
skal være lett tilgjengelig."
13
FORSIKTIG: Lufteventilene må ikke blokkeres, og må ha fri tilgang til luft med
romtemperatur for avkjøling.
14
DRIFTSTEMPERATUR: Dette produktet er konstruert for bruk i maksimum
romtemperatur på 40 grader celsius.
15
ALLE LAND: Produktet må installeres i samsvar med de lokale og nasjonale
elektriske koder.
AT-9410GB Installation Guide
Padrões: Este produto atende aos seguintes padrões.
1
Emissão de interferência de radiofrequência
FCC Classe A, EN55022 Classe A,
CISPR22 Class A (VCCI), AS/
NZS3548 (C-TICK), EN61000-3-2,
EN61000-3-3
2
AVISO: Num ambiente doméstico este produto pode causar interferência na
radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas
adequadas.
3
Imunidade
EN55024
4
Segurança Eléctrica
UL 1950 (UL/cUL), EN60950
5
Laser
EN60825
SEGURANÇA
6
AVISO Produto laser de classe 1
7
AVISO Não olhe fixamente para o raio.
8
AVISOS SOBRE CARACTERÍSTICAS ELÉTRICAS
ATENÇÃO: PERIGO DE CHOQUE ELÉTRICO
Para evitar CHOQUE ELÉTRICO, não retire a tampa. Não contém peças que possam
ser consertadas pelo usuário. Este aparelho contém VOLTAGENS PERIGOSAS e só
deve ser aberto por um técnico qualificado e treinado. Para evitar a possibilidade de
CHOQUE ELÉTRICO, desconecte o aparelho da fonte de energia elétrica antes de
conectar e desconectar os cabos da LAN.
9
PERIGO DE CHOQUE CAUSADO POR RAIO
PERIGO: NÃO TRABALHE no equipamento ou nos CABOS durante períodos
suscetíveis a QUEDAS DE RAIO.
10
CUIDADO: O CABO DE ALIMENTAÇÃO É UTILIZADO COMO UM DISPOSITIVO DE
DESCONEXÃO. PARA DESELETRIFICAR O EQUIPAMENTO, desconecte o cabo de
ALIMENTAÇÃO.
11
ELÉTRICO - EQUIPAMENTOS DO TIPO CLASSE 1
DEVE SER FEITA LIGAÇÃO DE FIO TERRA PARA ESTE EQUIPAMENTO. O plugue de
alimentação deve ser conectado a uma tomada com adequada ligação de fio terra.
Tomadas sem adequada ligação de fio terra podem transmitir voltagens perigosas a
peças metálicas expostas.
12
EQUIPAMENTO DE LIGAÇÃO, a tomada eléctrica deve estar instalada perto do
equipamento e ser de fácil acesso."
13
CUIDADO: As aberturas de ventilação não devem ser bloqueadas e devem ter
acesso livre ao ar ambiente para arrefecimento adequado do aparelho.
14
TEMPERATURA DE FUNCIONAMENTO: Este produto foi projetado para uma
temperatura ambiente máxima de 40 graus centígrados.
15
TODOS OS PAÍSES: Instale o produto de acordo com as normas nacionais e locais
para instalações elétricas.
75
Translated Electrical Safety and Emission Information
76
Estándares: Este producto cumple con los siguientes estándares.
1
Emisión RFI
FCC Clase A, EN55022 Clase A, CISPR22
Class A (VCCI), AS/NZS3548 (C-TICK),
EN61000-3-2, EN61000-3-3
2
ADVERTENCIA: en un entorno doméstico, este producto puede causar
radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las
medidas que sean convenientes al respecto.
3
Inmunidad
EN55024
4
Seguridad eléctrica
UL 1950 (UL/cUL), EN60950
5
Laser
EN60825
SEGURIDAD
6
¡ADVERTENCIA! Producto láser Clase 1.
7
¡ADVERTENCIA! No mirat fijamente el haz.
8
AVISOS ELECTRICOS
ADVERTENCIA: PELIGRO DE ELECTROCHOQUE
Para evitar un ELECTROCHOQUE, no quite la tapa. No hay ningún componente en el
interior al cual puede prestar servicio el usuario. Esta unidad contiene VOLTAJES
PELIGROSOS y sólo deberá abrirla un técnico entrenado y calificado. Para evitar la
posibilidad de ELECTROCHOQUE desconecte la corriente eléctrica que llega al
producto antes de conectar o desconectar los cables LAN.
9
PELIGRO DE RAYOS
PELIGRO: NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en los equipos o en
LOS CABLES durante TORMENTAS ELECTRICAS.
10
ATENCION: EL CABLE DE ALIMENTACION SE USA COMO UN
DISPOSITIVO DE DESCONEXION. PARA DESACTIVAR EL EQUIPO, desconecte el cable
de alimentación.
11
ELECTRICO - EQUIPO DEL TIPO CLASE 1
ESTE EQUIPO TIENE QUE TENER CONEXION A TIERRA. El cable tiene que conectarse a
un enchufe a tierra debidamente instalado. Un enchufe que no está correctamente
instalado podría ocasionar tensiones peligrosas en las partes metálicas que están
expuestas.
12
EQUIPO CONECTABLE, el tomacorriente se debe instalar cerca del equipo, en un
lugar con acceso fácil".
13
ATENCION: Las aberturas para ventilación no deberán bloquearse y deberán tener
acceso libre al aire ambiental de la sala para su enfriamiento.
14
TEMPERATURA REQUERIDA PARA LA OPERACIÓN: Este producto está diseñado
para una temperatura ambiental máxima de 40 grados C.
15
PARA TODOS LOS PAÍSES: Monte el producto de acuerdo con los Códigos
Eléctricos locales y nacionales.
AT-9410GB Installation Guide
Standarder: Denna produkt uppfyller följande standarder.
1
Radiostörning
FCC Klass A, EN55022 Klass A, CISPR22
Class A (VCCI), AS/NZS3548 (C-TICK),
EN61000-3-2, EN61000-3-3
2
VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan
tvinga användaren till att vidtaga erforderliga åtgärder.
3
Immunitet
EN55024
4
Elsäkerhet
UL 1950 (UL/cUL), EN60950
5
Laser
EN60825
SÄKERHET
6
VARNING! Laserprodukt av klass 1.
7
VARNING! Laserstrålning när enheten är öppen.
8
TILLKÄNNAGIVANDEN BETRÄFFANDE ELEKTRICITETSRISK:
RISK FÖR ELEKTRISK STÖTFör att undvika ELEKTRISK stöt, ta ej av locket. Det finns
inga delar inuti som behöver underhållas. Denna apparat är under HÖGSPÄNNING
och får endast öppnas av en utbildad kvalificerad tekniker. För att undvika
ELEKTRISK STÖT, koppla ifrån produktens strömanslutning innan LAN-kablarna
ansluts eller kopplas ur.
9
FARA FÖR BLIXTNEDSLAG
FARA: ARBETA EJ på utrustningen eller kablarna vid ÅSKVÄDER.
10
VARNING: NÄTKABELN ANVÄNDS SOM STRÖMBRYTARE FÖR ATT KOPPLA FRÅN
STRÖMMEN, dra ur nätkabeln.
11
ELEKTRISKT - TYP KLASS 1 UTRUSTNING
DENNA UTRUSTNING MÅSTE VARA JORDAD. Nätkabeln måste vara ansluten till ett
ordentligt jordat uttag. Ett felaktigt uttag kan göra att närliggande metalldelar
utsätts för högspänning. Apparaten skall anslutas till jordat uttag, när den ansluts till
ett nätverk.
12
UTRUSTNING MED PLUGG. Uttaget skall installeras i utrustningens närhet och vara
lättåtkomligt".
13
VARNING: Luftventilerna får ej blockeras och måste ha fri tillgång till omgivande
rumsluft för avsvalning.
14
DRIFTSTEMPERATUR: Denna produkt är konstruerad för rumstemperatur ej
överstigande 40 grader Celsius.
15
ALLA LÄNDER: Installera produkten i enlighet med lokala och statliga bestämmelser
för elektrisk utrustning.
77
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising