Monogram | ZDIS150 | Owner`s manual | Monogram ZDIS150 Owner`s manual

Monogram ZDIS150 Owner`s manual
Owner’s
Manual
Automatic
Ice Maker
ZDIC150
ZDIS150
monogram.com
Consumer Information
Ice maker
Contents
Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . 10–12
Consumer Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Controls and Features . . . . . . . . . . . . . . . . . . . . . . . . 7, 8
Important Phone Numbers . . . . . . . . . . . . . . . . . . . . 15
Model and Serial Numbers. . . . . . . . . . . . . . . . . . . . . . 2
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Problem Solver . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13, 14
Product Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Repair Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important Safety Instructions . . . . . . . . . . . . . . . . . 3–5
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Before
using your
ice maker
Read this manual carefully. It is intended to help
you operate and maintain your new ice maker
properly.
Keep it handy for answers to your questions.
If you don’t understand something or need more
help, there is a list of toll-free consumer service
numbers included in the back section of this
manual.
OR
Visit our Website at: monogram.com
Write
down the
model
& serial
numbers
You’ll find them on a label on the right wall of the
ice storage bin.
Please write these numbers here:
These numbers are also on the Consumer
Product Ownership Registration Card packed
separately with your ice maker.
Model Number
Serial Number
Use these numbers in any correspondence or
service calls concerning your ice maker.
If you
received a
damaged ice
maker
Immediately contact the dealer (or builder) that
sold you the ice maker.
If you
need
service
To obtain service, see the Consumer Services
page in the back of this manual.
We’re proud of our service and want you to be
pleased. If for some reason you are not happy
with the service you receive, follow these steps.
FIRST, contact the people who serviced your
appliance. Explain why you are not pleased.
In most cases, this will solve the problem.
NEXT, contact us at GEAppliances.com or call
800.GE.CARES.
2
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
Before it is used, the ice maker must be properly
installed and located as described in this manual.
WARNING: To reduce the risk of death,
•
•
•
•
•
fire, electrical shock or injury when using your ice
maker, follow basic precautions including the
following:
Never allow children to operate, play with or crawl
inside the ice maker.
Never clean ice maker parts with flammable fluids.
The fumes can create a fire hazard or explosion.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance. The fumes can create a fire
hazard or explosion.
Be sure your ice maker is properly installed and
grounded by a qualified technician in accordance
with the Installation Instructions.
Do not attempt to repair or replace any part
of your ice maker unless it is specifically
recommended in this manual. All other servicing
should be referred to a qualified technician.
• Unplug the ice maker or disconnect power before
cleaning, servicing or changing the light bulb.
Failure to do so can result in death or electrical
shock.
• It is your responsibility to be sure your ice maker:
– has been installed where it is protected from the
elements.
– is located so that the front is not blocked to restrict
incoming or discharge air flow.
– is connected only to the proper kind of outlet, with
the correct electric supply and grounding. A 115 volt,
60 Hz., 15 amp fused electrical supply is required.
NOTE: Time delay fuse or circuit breaker is
recommended.
– is not used by anyone unable to operate it properly.
– is used only to do what ice makers are designed to do.
– is properly maintained.
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
LIRE ET CONSERVER CES INSTRUCTIONS
Avant son utilisation, la machine à glaçons doit être bien
installée et située selon la description dans ce manuel.
AVERTISSEMENT : Pour réduire
•
•
•
•
•
les risques d’incendie, de choc électrique ou
de blessure lors de l’utilisation de la machine à
glaçons, suivre les précautions fondamentales,
y compris les suivantes :
Ne jamais laisser les enfants utiliser, employer
comme jouet ou pénétrer dans la machine à
glaçons.
Ne jamais nettoyer les pièces de la machine
à glaçons avec des fluides inflammables. Les
émanations peuvent créer un risque d’incendie ou
d’explosion.
Ne pas entreposer ni utiliser de l’essence ou
d’autres vapeurs et liquides inflammables dans
le voisinage de cet appareil ménager ou de tout
autre appareil. Les émanations peuvent créer un
risque d’incendie ou d’explosion.
S’assurer que la machine à glaçons est bien
installée et reliée à la terre par un technicien
qualifié, et conformément aux instructions
d’installation.
Ne pas essayer de réparer ou de remplacer une
pièce de votre machine à glaçons à moins de
recommandations spécifiques dans ce manuel.
•
•
–
–
–
–
–
–
Tout autre besoin de service doit être soumis à un
technicien qualifié.
Débrancher la machine à glaçons ou déconnecter
le courant électrique avant de la nettoyer, de
l’entretenir ou de changer l’ampoule d’éclairage.
L’omission d’observer ces précautions peut causer
un décès ou un choc électrique.
Vous avez la responsabilité de vous assurer que la
machine à glaçons :
a été installée où elle est protégée contre les
intempéries.
est située de sorte que le devant n’est pas obstruée
pour restreindre l’arrivée ou la sortie du courant
d’air.
est connectée seulement au type approprié de
prise de courant avec une alimentation électrique
correcte et une liaison à la terre. Une alimentation
électrique de 115 V, 60 Hz, et fusible de 15 A est
requise.
REMARQUE : Les fusibles temporisés ou
disjoncteurs de circuit sont recommandés.
n’est pas utilisée par quiconque ne peut faire
fonctionner l’appareil d’une manière appropriée.
est utilisée seulement pour accomplir ce que les
machines à glaçons sont destinées à fournir.
est soumise à un entretien approprié.
3
IMPORTANT SAFETY INSTRUCTIONS
WARNING! Failure to follow these instructions can result in death, fire, or electrical shock.
non-respect de ces instructions peut causer la mort, un incendie ou
AVERTISSEMENT ! Le
un choc électrique.
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or
remove the third (ground) prong from the
power cord. For personal safety, this appliance
must be properly grounded.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet
to minimize the possibility of electric shock
hazard from this appliance.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
Where a standard 2-prong wall outlet is
encountered, it is your personal responsibility
and obligation to have it replaced with a
properly grounded 3-prong wall outlet.
The ice maker should always be plugged into
its own individual electrical outlet which has a
voltage rating that matches the rating plate.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
Never unplug your ice maker by pulling on the
power cord. Always grip plug firmly and pull
straight out from the outlet.
Repair or replace immediately all power cords
that have become frayed or otherwise damaged.
Do not use a cord that shows cracks or abrasion
damage along its length or at either end.
When moving the ice maker, be careful not to
roll over or damage the power cord.
RACCORDEMENT ÉLECTRIQUE
Ne coupez ni retirez en aucun cas la troisième
broche (mise à la terre) de la fiche du cordon
d’alimentation. Pour votre sécurité, cet appareil
doit être correctement mis à la terre.
Le cordon d’alimentation de cet appareil est
muni d’une fiche à 3 broches (mise à la terre)
qui se branche dans une prise mural ordinaire
à 3 alvéoles (mise à la terre) pour réduire au
minimum les risques du chocs électriques.
Faites examiner la prise de courant et le circuit
par un électricien qualifié pour vous assurer que
la prise est correctement mise à la terre.
Si la prise murale est du type standard à 2 alvéoles,
il vous incombe de la faire remplacer par une prise
à 3 alvéoles correctement mise à la terre.
La machine à glaçons doit toujours être branché
dans sa propre prise de courant, dont la tension
nominale est identique à celle indiquée sur la
plaque signalétique.
EXTENSION CORDS
Do not use an extension cord with this appliance.
RALLONGES
N’utilisez pas de rallonge avec cet appareil.
4
Cette précaution est recommandée pour
garantir un rendement optimum et éviter
une surcharge des circuits électriques de
la résidence, ce qui pourrait créer un risque
d’incendie par surschauffe des fils.
Ne débranchez jamais la machine à glaçons
en tirant le cordon d’alimentation. Saisissez
fermement la fiche du cordon et tirez droit
pour la retirer de la prise.
Réparez ou remplacez immédiatement tout
cordon effiloché ou endommagé. N’utilisez pas
un cordon fendillé ou présentant des signes
d’usure.
Lorsque vous déplacez votre machine à glaçons
du mur, faites attention de ne pas la faire rouler
sur le cordon d’alimentation afin de ne pas
l’endommager.
IMPORTANT SAFETY INSTRUCTIONS
DANGER: RISK OF CHILD ENTRAPMENT
Child entrapment and suffocation are not
problems of the past. Junked or abandoned
refrigeration products are still dangerous… even
if they will sit for “just a few days.” If you are
getting rid of your old appliance, please follow
these instructions to help prevent accidents.
Before You Throw Away Your Old
Refrigeration Product:
• Take off the doors.
• Leave the shelves in place so that children
may not easily climb inside.
DANGER! RISQUES POUR LES ENFANTS
Les enfants pris au piège ou morts d’asphyxie
sont toujours d’actualité. Les appareils de
réfrigération abandonés sont toujours aussi
dangereux, même si on n’attend que “quelque
jours” pour s’en débarasser. Si vous ne gardez
pas votre ancien appareil, veuillez suivre les
directives ci-dessous afin de prévenir les
accidents.
Avant de vous débarasser de votre vieux
appareil de réfrigération :
• Démontez les portes.
• Laissez les clayettes en place afin d’empêcher
les enfants de grimper à l’intérieur.
REFRIGERANTS
All refrigeration products contain refrigerants,
which under federal law must be removed
prior to product disposal. If you are getting rid
of an old refrigeration product, check with the
company handling the disposal about what
to do.
RÉFRIGÉRANTS
Tous les appareils de réfrigération contiennent
des réfrigérants qui, conformément aux
lois fédérales, doivent être enlevés avant
toute élimination de l’appareil. Si vous vous
débarrassez de vieux appareils de réfrigération,
vérifiez, auprès de la société qui s’occupe de
leur élimination, ce que vous devez faire.
5
Controls and Features
Ice maker
Remove
packaging
IMPORTANT: Do not remove any permanent
instruction labels inside your ice maker or the
Tech Sheet that is fastened behind the lower
access panel.
• Remove tape and any labels from your
ice maker before using (except the model and
serial number label).
• Do not use sharp instruments, rubbing alcohol,
flammable fluids or abrasive cleaners to
remove tape or glue. These products can
damage the surface of your ice maker. For
more information, see Important Safety
Instructions.
To remove any remaining tape or glue, rub
the area briskly with your thumb. Tape or glue
residue can also be easily removed by rubbing
a small amount of liquid dish soap over the
adhesive with your fingers. Wipe with warm
water and dry.
Clean before
using
After you remove all of the packaging materials,
clean the inside of your ice maker before using it.
See the cleaning instructions in Care and
Cleaning.
Set controls
ON/OFF
Press ON/OFF to start ice production or stop ice
maker operation. When the ice maker is in ON
mode, ice production is in progress and the ON/
OFF LED light will be on. When ice maker is in OFF
mode and ice maker operations are turned off,
the ON/OFF LED will remain off.
QUICK ICE MODE
Press QUICK ICE to start or stop more rapid ice
production. Select the QUICK ICE feature when
you have an upcoming need for a large amount
of ice and the bin is low or empty. Quick Ice
Mode will produce a greater quantity of ice in a
24-hour period.
The QUICK ICE indicator light is illuminated when
the ice maker is in Quick Ice Mode.
Pressing QUICK ICE to turn Quick Ice Mode off will
not stop ice production.
When ice production is turned on, the ice maker
will automatically enter Quick Ice Mode for the
first 24 hours.
NOTE: Allow 24 hours to produce the first batch
of ice after installing ice maker. Discard the first
two batches produced after installation.
NOTE: Power to the ice maker is not shut off
when the ice maker is in OFF mode.
To stop ice maker operation, press ON/OFF.
CLEAN
It is recommended that you clean the ice maker
if the CLEANING NEEDED light is illuminated, if 6
months have elapsed since the last cleaning, or
if ice production decreases significantly. To clean
your ice maker, see Care and Cleaning -- Cleaning
Cycle.
CLEANING DONE
REPLACE
CLEANING NEEDED
FILTER
ADD CLEANER
ON/OFF
CLEAN
TURN UNIT OFF BEFORE CLEANING
SEE USE AND CARE MANUAL
6
QUICK ICE
Controls and Features
Ice maker
Control
messages
REPLACE FILTER will illuminate when the
control system recommends installing a new
filter or when the control system senses that a
filter is not inserted in the ice maker. See Care
and Cleaning - Ice Maker System.
CLEANING NEEDED will illuminate when the
control system recommends a CLEAN cycle. See
Care and Cleaning - Ice Maker System.
ADD CLEANER will illuminate when a CLEAN
cycle has been initiated but no cleaning
solution is in the reservoir. See Care and
Cleaning -- Cleaning Cycle.
CLEANING DONE will illuminate when the
CLEAN cycle is complete.
If the ON/OFF LED is flashing, see The Problem
Solver.
The Door Ajar Alarm feature will sound an
alarm when the ice maker door has been open
for 5 minutes. The alarm will repeat every 2
minutes. Close the door to turn off the alarm
and reset the feature.
CLEANING DONE
REPLACE
CLEANING NEEDED
FILTER
ADD CLEANER
ON/OFF
CLEAN
QUICK ICE
TURN UNIT OFF BEFORE CLEANING
SEE USE AND CARE MANUAL
Features of your
ice maker
Filter
Control panel
Model
& serial
numbers
Cutter grid cover
Water reservoir
Ice level
sensor
Ice retainer baffle
Condenser (behind
lower access panel)
Magnetic
door catch
Lower access panel
Ice scoop
7
Operating Instructions
Ice maker
How your
ice maker
works
When you first start your ice maker, the water
will flow through the filter and fill the reservoir.
The system will rinse itself before starting to
make ice. The rinsing process takes about five
minutes.
2. When the desired thickness is reached, the
ice sheet is released and slides onto a cutter
grid. The grid divides the sheet into individual
cubes.
Under normal operating conditions, the ice
maker will cycle on and off as needed.
The ice level sensor located in the ice storage
bin will monitor the ice levels.
IMPORTANT
If the water supply to the ice maker is turned off,
be sure to set the ice maker control to
OFF. Drain the water reservoir and leave
the ice maker door open to allow it to dry
completely.
Making Ice
1. Water is constantly circulated over a
freezing plate. As the water freezes into ice,
the minerals in the water are rejected. This
produces a clear sheet of ice with a low
mineral content.
3. The water containing the rejected minerals
is drained after each freezing cycle.
4. Fresh water enters the machine and is filtered
for the next ice making cycle.
5. Cubes fall into the storage bin. When the bin
is full, the ice maker shuts off automatically
and restarts when more ice is needed. The
ice bin is not refrigerated and some melting
will occur. The amount of melting varies with
room temperature.
NOTE: As the room and water temperatures
vary, so will the amount of ice produced and
stored. This means that higher operating
temperatures result in reduced ice production.
8
Care and Cleaning
Ice maker
Ice maker
system care
Exterior
surfaces
Interior
components
CLEANING NEEDED will illuminate when the
electronic control senses that the need for
cleaning is approaching. At this time you need to
purchase Nickel Safe Ice Machine Cleaner by Nu
Calgon, available at most appliance repair shops
or through GE Parts and Accessories. Order
part number WX08X42870. In the U.S.A., call
1.800.626.2002. or visit GEApplianceParts.com.
In Canada call 1.800.561.3344. The ice maker
must be cleaned, otherwise ice production may
decrease significantly or stop.
REPLACE FILTER will illuminate when the
electronic control senses that the filter needs to
be replaced. At this time you need to purchase a
replacement filter, part number IMWF, through GE
parts at www.gewaterfilters.com or in the US call
1.800.626.2002.
Keep the outside clean. Wipe with a clean cloth
lightly dampened with mild liquid dish detergent.
Dry with a clean, soft cloth. Do not wipe the ice
maker with a soiled dish cloth or wet towel. These
may leave a residue that can damage the finish.
Do not use scouring pads, powdered cleaners,
bleach or cleaners containing bleach because
these products can scratch and damage the
finish.
6WDLQOHVVVWHHO³Regularly clean and polish the
stainless steel door panels and handles (on
some models) with a commercially available
stainless steel cleaner such as Stainless Steel
Magic™ to preserve and protect the fine finish.
Order part number WX10X15. In the U.S.A. call
1.800.626.2002 or visit GEApplianceParts.com. In
Canada call 1.800.561.3344.
WARNING: Disconnect electrical
power to the ice maker before cleaning. Failure
to do so can result in death, fie, or electrical
shock.
AVERTISSEMENT !
Débranchez l'alimentation électrique à la
machine à glaçons avant le nettoyage.
L’omission de prendre cette précaution peut
entraîner la mort, l'incendie ou le choc électrique.
1. Open the storage bin door and remove any ice
that is in the bin.
2. Pull out on the bottom of the cutter grid cover
until the snaps release to remove.
3. Remove ice scoop and ice scoop holder.
Remove the two screws using a 1/4" ratchet.
NOTE: Do not remove hoses. Do not wash plastic
parts in dishwasher. They cannot withstand
temperatures above 145°F (63°C).
Product designed and tested for use with
genuine GE water filters. Non-GE filters are not
covered under product warranty.
Do not use appliance wax or polish on the
stainless steel.
grid cover, door gasket, and secured interior
components (cutter grid, exterior of hoses, and
water reservoir). Rinse with clean water.
5. Clean the same parts again with a solution of
1 tbsp. (15 ml) of household bleach in 1 gal. (3.8
L) warm water. Rinse thoroughly with clean
water.
6. Gently wipe the control panel with a soft, clean
dishcloth using warm water and a mild liquid
dish detergent.
7. Replace ice scoop holder.
8. Replace the cutter grid cover by aligning top
tabs and pushing to snap into place.
9. Plug in ice maker or reconnect power.
NOTE: The air cooled condenser needs to be
cleaned regularly for efficient ice production and
energy conservation. See Care and Cleaning Condenser section.
4. With mild soap and warm water wash the
storage bin, ice scoop and holder, cutter
9
Care and Cleaning
Ice maker
Cleaning
cycle
For best performance, perform a cleaning cycle
every six months. Nickel Safe Ice Machine Cleaner
by Nu Calgon is available at appliance repair
shops, or through GE Parts and Accessories. Order
part number WX08X42870. In the U.S.A., call
1.800.626.2002 or visit GEApplianceParts.com. In
Canada, call 1.800.561.3344. To clean ice maker
system, follow these instructions.
1. Turn ice production off. Remove all ice from
storage bin.
2. To improve accessibility, remove cutter grid
cover by pulling bottom of cover down and
then forward.
3. Unscrew the drain cap from the bottom of the
water reservoir. Drain all water in reservoir.
Cutter
grid
cover
Water
reservoir
Drain
cap
4. Replace the drain cap securely.
NOTE: If the cap is not securely tightened, water
can leak, causing thin ice or no ice.
5. Pour the entire 16 oz. bottle of Nickel Safe Ice
Machine Cleaner into water reservoir. Follow all
safety precautions on the bottle. Fill the bottle
twice with tap water and pour it into the water
10
reservoir.
6. Replace the cutter grid cover. Insert the top
tabs first, and then push toward cutter grid to
snap into place.
7. Touch the CLEAN button. The CLEAN LED will
illuminate and the cleaning cycle will begin. If
Invalid Tone plays, press the ON/OFF button
to turn the ice maker off and try again. If "ADD
CLEANING DONE
CLEANING NEEDED
ADD CLEANER
CLEAN
TURN UNIT OFF BEFORE CLEANING
SEE USE AND CARE MANUAL
CLEANER" illuminates, see previous steps.
8. When the cycle is complete the CLEAN LED will
turn off, the Cycle Complete tone will sound,
and the “CLEANING DONE” text will illuminate.
9. After the cleaning cycle is complete, remove the
drain cap from the water reservoir to see if any
of the green cleaning solution is left in the water
reservoir. If cleaning solution drains from the
water reservoir, you should run the clean cycle
again adding only tap water to the reservoir.
Be sure to replace the drain cap before running
the cycle again.
NOTE: Severe scale buildup may require repeated
cleaning with a fresh quantity of cleaning solution.
10.Press the ON/OFF button to resume ice
production. Discard the first batch of ice.
NOTE: To stop the cleaning cycle prematurely,
press ON/OFF. The CLEAN LED will turn off and
you will hear the Power Off tone. If power is lost
before cycle is complete, cleaning will continue
when the ice maker powers on.
Care and Cleaning
Ice maker
Condenser
WARNING: Disconnect electrical
power to the ice maker before cleaning.
Failure to do so can result in death, fie, or
electrical shock.
AVERTISSEMENT !
Débranchez l'alimentation électrique à la
machine à glaçons avant le nettoyage.
L’omission de prendre cette précaution
peut entraîner la mort, l'incendie ou le choc
électrique.
For best performance, brush or vacuum lint and
dirt from the condenser at least once a year.
A dirty or clogged condenser:
• Uses more energy.
• Prevents proper airflow.
• Reduces ice making capacity.
• Causes higher than recommended operating
temperatures which may lead to component
failure.
1. Unplug the ice maker or disconnect power.
2. Remove the 2 screws in the lower access
panel and the 2 screws from the base grille
area of the front panel support.
3. Pull the bottom forward and then pull down to
remove the lower access panel.
4. Remove dirt and lint from the condenser
fins and the unit compartment with a brush
attachment attached to a vacuum cleaner.
5. Replace the lower access panel using the 4
screws.
6. Plug in the ice maker or reconnect power.
11
Care and Cleaning
Ice maker
Filter
replacement
Product designed and tested for use with
genuine GE water filters. Non-GE filters are not
covered under product warranty. Order part
number IMWF. In the U.S.A. call 1.800.626.2002
or visit GEApplianceParts.com. In Canada call
1.800.561.3344.
Cover
O-Rings
Alignment Pin
Alignment
Arrow
1. Locate the water filter on the right-hand side of
the ice maker controls.
2. Remove the filter by rotating counterclockwise
from the lock to unlock position.
4. Align the pin on the side of the filter with the
cutout channel in the filter housing and insert
filter.
Unlocked
:DWHU¿OWHU
Unlock
symbol
Lock
symbol
Locked
3. Remove the cover from the new water filter. Be
sure the O-rings are still in place after the cover
is removed.
Alignment Pin
5. Turn filter clockwise until it locks into the
housing. Ensure the alignment arrow on the
filter head is aligned with the locked symbol on
the control box housing.
NOTE: If the filter is not correctly locked into
place, the ice maker will not produce ice.
Vacation
and moving
To shut down the ice maker:
1. Unplug the ice maker or disconnect power.
2. Remove all ice from the storage bin.
3. Shut off the water supply. If the ambient
temperature of the room will drop below 32°F
(0°C), water must be removed from the drain
line.
For ice makers with a drain pump installed:
1. Plug in ice maker or reconnect power.
2. Turn ice production off and remove all
remaining ice from ice bin.
Reverse
Osmosis
system
IMPORTANT: The performance of the ice maker
may be affected when connected to a Reverse
Osmosis system. An RO system may also reduce
water pressure and affect the fill cycle, which is
dependent on time and flow. The reduced water
pressure may cause the reservoir not to fill and
flush properly during the ice making cycle.
The pressure of the water supply coming out
of a reverse osmosis system going to the water
inlet valve of the ice maker needs to be between
30 and 120 psi.
12
3. Pour 1 gallon. (3.78541 L) of water into the ice
bin near the drain and let the ice maker stand
for approximately 5 minutes. This will allow
the water in the bin to drain into the drain
pump so the pump will remove the remaining
water from the ice bin and drain the pump.
4. Unplug ice maker or disconnect power.
Before using again, clean the ice maker and
storage bin. Plug in the ice maker or reconnect
power and turn on the water supply tor resume
ice making operation.
If a reverse osmosis water filtration system is
connected to your cold water supply, the water
pressure to the reverse osmosis system needs
to be a minimum of 40 psi. The reverse osmosis
system must provide 1 gal. of water per hour
to the ice maker for proper ice maker operation.
Do not use copper tubing when the ice maker is
connected to a Reverse Osmosis water system.
The Problem Solver
Ice maker
Normal
sounds
Questions?
Use this
problem
solver!
Your new ice maker may make sounds that
are not familiar to you. Most of the sounds are
normal. Hard surfaces such as floors, walls and
cabinets can make the sounds seem louder than
they actually are. The following describes the
kinds of sounds that might be new to you and
what may be making them.
z You will hear a buzzing sound when the water
valve opens to fill the water pan for each
cycle.
z Rattling noises may come from the flow of the
refrigerant or the water line. Items stored on
top of the ice maker can also make noises.
z The high-efficiency compressor may make a
pulsating or high pitched sound.
z Water running over the evaporator plate may
make a splashing sound.
z Water running from the evaporator plate to
the water pan may make a splashing sound.
z As each cycle ends, you may hear a gurgling
sound due to the refrigerant flowing in your
ice maker.
z You may hear air being forced over the
condenser by the condenser fan.
z During the harvest cycle, you may hear a
“thud” when the ice sheet slides from the
evaporator onto the cutter grid.
z When you first start the ice maker, you may
hear water running continuously. The ice
maker is programmed to run a rinse cycle
before it begins to make ice.
z If the ice maker is connected to a water supply
pressure in excess of 60 psi, you may hear
a loud sound during water filling associated
with the flow of water through the inlet valve.
Call a licensed, qualified plumber to determine
the best method to reduce the supply water
pressure (50 psi is recommended).
Problem
Possible Cause
ON/OFF LED is
ÀDVKLQJ
7KLVVLJQL¿HVDQLFHOHYHOVHQVRUHUURU
Unplug ice maker and remove the cutter grid cover (see Care and Cleaning –
Interior Components). Make sure the white wiring connector going up to the
control housing on the right side is connected securely.
Ice maker will not
turn on
Check that it is plugged into a grounded 3 prong outlet.
Be sure that the control is turned on. See “Using the Controls.”
Replace the fuse or reset the circuit breaker.
NOTE: If problems continue, contact an electrician.
Room temperature must be above 55°F (13°C). Otherwise, bin thermostat
PD\VHQVHFROGURRPWHPSHUDWXUHDQGVKXWRȺHYHQWKRXJKWKHELQLVQRW
IXOORILFH7KHLFHPDNHUPD\QRWUHVWDUWRQFHLWGRHVVKXWRȺ
If there was a large amount of water added to the ice maker, wait a few
minutes for the drain pump to clear. If there is still water in the bin, check to
see whether the drain hose is kinked.
For models with drain pumps, check that the drain hose is not damaged, or
kinked or pinched between cabinet and ice maker. Use only GE approved
drain pump kit, Part ZPK2.
13
The Problem Solver
Ice maker
Questions?
Use this
problem
solver!
14
Problem
Possible Cause
Ice maker seems noisy
,VWKHZDWHULQWKHZDWHUSDQRYHUÀRZLQJ"7KLVLVQRUPDO7KLVRYHUÀRZ
helps to purge minerals that were removed from the water during the ice
making process.
,VWKHUHD´ZKRRVKLQJµVRXQG"Check the following things:
■ Make sure that the water supply is hooked up and turned on.
■ Make sure that the drain cap is tight and the water drain pan pump is
securely attached to the water pan.
,VWKHUHLFHEHWZHHQWKHHYDSRUDWRUSODWHDQGWKHFXWWLQJJULG"Check
that the ice maker is level. See “Leveling.” If the ice maker is level, and the
problem persists, run a cleaning cycle. See “Cleaning.”
If the ice maker is connected to a water supply pressure in excess of 60
SVL\RXPD\KHDUDORXGVRXQGGXULQJZDWHU¿OOLQJDVVRFLDWHGZLWKWKH
ÀRZRIZDWHUWKURXJKWKHLQOHWYDOYH&DOODOLFHQVHGTXDOL¿HGSOXPEHUWR
determine the best method to reduce the supply water pressure (50 psi is
recommended).
Ice maker runs but
produces no ice
Make sure the control is turned on.
Make sure the water supply is properly connected and turned on.
If the drain cap is loose, water will empty from the water pan, and you will
have either thin ice or no ice. Tighten the drain cap.
Clean the drain tube.
Be sure that there are no kinks in the drain line.
Ice maker runs but
produces very little ice
Is the “QUICK ICE” feature turned on? This feature increases the ice
production rate to provide you with more ice in the same amount of time.
See Control Settings.
Room temperatures of more than 90ºF (32ºC) will normally reduce ice
production.
'LUWRUOLQWPD\EHEORFNLQJWKHDLUÀRZWKURXJKWKHFRQGHQVHU6HH
Condenser in the Cleaning section.
If there is white scale buildup in the interior of the ice maker, you should
clean the ice maker. See Interior Components in the Cleaning section.
If the drain cap is loose, water will empty from the water pan, and you will
have either thin ice or no ice.
Tighten the drain cap.
2ȺWDVWHRGRURUJUD\
color in the ice
,VWKHUHXQXVXDOO\KLJKPLQHUDOFRQWHQWLQWKHZDWHUVXSSO\"The water
PD\QHHGWREHWUHDWHGRUWKH¿OWHUPD\QHHGWREHUHSODFHG
,VWKHUHPLQHUDOVFDOHEXLOGXS" Clean your ice maker. See Ice Maker
System in the Cleaning section.
Do not store any foods in the ice bin. Clean ice storage bin.
Make sure that all packaging materials were removed at the time of
installation.
Thin, soft or clumps of
ice
,VWKHUHXQXVXDOO\KLJKPLQHUDOFRQWHQWLQWKHZDWHUVXSSO\"The water
PD\QHHGWREHWUHDWHGRUWKH¿OWHUPD\QHHGWREHUHSODFHG
,VWKHUHPLQHUDOVFDOHEXLOGXS" Clean your ice maker. See Ice Maker
System in the Cleaning section.
$UHWKHUHFOXPSVRILFHLQWKHELQ"If ice is not used regularly, it will melt
and form clumps. Break the clumps with the ice scoop provided.
Water not entering
drain properly
,VWKHGUDLQKRVHDOLJQHGRYHUWKHGUDLQ" Move the ice maker to align with
the drain. See Connect Water Supply.
NOTE: Service technicians cannot repair plumbing problems outside of the
LFHPDNHU&DOODOLFHQVHGTXDOL¿HGSOXPEHU
Consumer Services
Ice maker
With the purchase of your new Monogram appliance, receive the
assurance that if you ever need information or assistance from
GE, we will be there. All you have to do is call!
GE Answer Center®
In the USA:
1.800.626.2000
Whatever your question about any Monogram major appliance, GE Answer Center®
LQIRUPDWLRQVHUYLFHLVDYDLODEOHWRKHOS<RXUFDOO³DQG\RXUTXHVWLRQ³ZLOOEHDQVZHUHG
promptly and courteously. You can call any time. GE Answer Center® service is open
24 hours a day, Monday through Saturday.
OR
Visit our Website at: monogram.com
In Canada, call 1.800.561.3344.
In-Home Repair
Service
In the USA:
1.800.444.1845
If your Monogram appliance should ever require service, you can depend on Monogram
Preferred Service. Simply call 1.800.444.1845, where our Monogram Preferred Service
Specialists are available 7 a.m. - 10 p.m. ET Monday through Friday and 8 a.m. - 6 p.m.
ET Saturday and Sunday to coordinate your service appointment. In Canada: Monday to Friday,
7:00 a.m. - 8:00 p.m. and Saturday, 8:00 a.m. - 5:00 p.m. EDST.
In Canada:
1.800.561.3344
For Customers With
Special Needs…
In the USA:
1.800.626.2000
Service Contracts
In the USA:
1.800.626.2224
GE offers Braille controls for a variety of GE appliances, and a brochure
to assist in planning a barrier-free kitchen for persons with limited
mobility.
Consumers with impaired hearing or speech who have access
to a TDD or a conventional teletypewriter may call 1.800.TDD.GEAC
(1.800.833.4322) to request information or service.
You can have the secure feeling that GE Consumer Service will still be there after your warranty
expires. Purchase a GE contract while your warranty is still in effect and you’ll receive a
substantial discount. With a multiple-year contract, you’re assured of future service at today’s
prices.
In Canada:
1.800.561.3344
Parts and
Accessories
In the USA:
1.800.626.2002
In Canada:
1.800.561.3344
Individuals qualified to service their own appliances can have parts or accessories sent directly
to their home. The GE parts system provides access to over 47,000 parts, and all GE Genuine
Renewal Parts are fully warranted. VISA, MasterCard and Discover cards are accepted.
Visit www.geappliances.com
User maintenance instructions contained in this manual cover procedures intended to be
performed by any user. Other servicing generally should be referred to qualified service
personnel. Caution must be exercised, improper servicing may cause unsafe operation.
15
Warranty
Ice maker
YOUR MONOGRAM Ice maker WARRANTY
Staple sales slip or canceled check here. Proof of original
purchase date is needed to obtain service under warranty.
WHAT IS
COVERED
From the Date
of the Original
Purchase
LIMITED ONE-YEAR WARRANTY
WHAT IS NOT
COVERED
• Service trips to your home to teach you how
to use the product.
• Replacement of house fuses or resetting of
circuit breakers.
• Damage to the product caused by accident, fire,
floods or acts of God.
• Failure of the product if it is used for other than
its intended purpose or used commercially.
• Damage caused after delivery.
For one year from date of original purchase, we will provide, free of charge, parts and service labor in your home
to repair or replace any part of the ice maker that fails because of a manufacturing defect.
LIMITED FIVE-YEAR WARRANTY
For five years from date of original purchase, we will provide, free of charge, parts and service labor
in your home to repair or replace any part of the sealed ice making system (the compressor, condenser,
evaporator and all connecting tubing) that fails because of a manufacturing defect.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for
ordinary home use in the 48 mainland states, Hawaii, Washington, D.C. or Canada. If the product is located
in an area where service by a GE Authorized Servicer is not available, you may be responsible for a trip charge
or you may be required to bring the product to an Authorized GE Service location for service. In Alaska the
warranty is the same except that it is LIMITED because you must pay to ship the product to the service shop
or for the service technician’s travel costs to your home.
All warranty service will be provided by our Factory Service Centers or by our authorized Customer Care®
servicers during normal working hours.
Should your appliance need service, during warranty period or beyond, in the USA call 1.800.444.1845. In
Canada: 1.800.561.3344. Please have your serial number and model number available when calling for service.
• Improper installation, delivery or maintenance.
If you have an installation problem, contact
your dealer or installer. You are responsible for
providing adequate electrical, plumbing and
other connecting facilities.
• Replacement of the light bulbs, if included.
• Incidental or consequential damage caused by
possible defects with this appliance.
• Product not accessible to provide required
service.
(;&/86,212),03/,(':$55$17,(6³<RXUVROHDQGH[FOXVLYHUHPHG\LVSURGXFWUHSDLUDVSURYLGHGLQ
this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or
fitness for a particular purpose, are limited to one year or the shortest period allowed by law.
Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state/province to province. To know what your legal rights are
in your state/province, consult your local or state/provincial consumer affairs office or your state’s Attorney General.
Warrantor in USA: General Electric Company,
Louisville, KY 40225
Warrantor in Canada: Mabe Canada Inc.
GE Appliances & Lighting
49-60692
224D1893P003
06-13 GE
Printed in the United States
Appliances
General Electric Company
Louisville, KY 40225
GEAppliances.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising