ClimateMaster | GT-PX Indoor Split Series | Installation manual | ClimateMaster GT-PX Indoor Split Series Installation manual

ClimateMaster GT-PX Indoor Split Series Installation manual
GT-PX Indoor Split Series (50YDS Models)
GT-PE Outdoor Split Series (50YPS Models)
Installation, Operation and Maintenance Instructions
Residential Split
Geothermal Heat Pumps
97B0048N02
Revised: 6 Dec., 2011
Table of Contents
Model Nomenclature
3
Electrical - Line Voltage
31
Safety
4
Electrical - Power Wiring
32
Storage
5
Electrical - HWG Wiring
32
Pre-Installation
5
Electrical - Low Voltage Wiring
33-37
Equipment Selection
6
Thermostat Wiring
33-37
Air Coil Match-ups
6-7
CXM Controls
38-40
Air Handler Selection
8
Unit Starting and Operating Conditions
41-42
Installation
9
Unit Start-Up Procedure
43
Water Connections
10
Unit Operating Conditions
44-45
Ground-Loop Heat Pump Applications
12-14
Preventive Maintenance
46
Ground-Water Heat Pump Applications Indoor Compressor Section Only
Troubleshooting
47
15
CXM Process Flow Chart
48
Water Quality Standards
17
Functional Troubleshooting
49-50
Lineset Information
18
Performance Troubleshooting
50
Refrigeration Installation
18-25
Troubleshooting Form
51
Hot Water Generator
26-30
Warranty
52
Indoor Compressor Section Only
28
Revision History
54
Hot Water Generator
Module Refrigeration Installation
Outdoor Compressor Section Only
29-30
This page was intentionally left blank.
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Model Nomenclature: for Split Series
Indoor Splits
<'6 1 & ' 3UHIL[
3DFNDJLQJ
6LQJOH3DFN'RPHVWLF
6HULHV
5HYLVLRQ/HYHO
<'6 ([WHQGHG5DQJH3XURQ8OWUD
+LJK(IILFLHQF\5HVLGHQWLDO6SOLW
&XUUHQW5HYLVLRQ
8QLW6L]H
9ROWDJH
$LU)ORZ&RQILJXUDWLRQ
+HDW([FKDQJHU2SWLRQV
63/,75(6,'(17,$/81,7
&RSSHU &XSUR1LFNHO
2SWLRQ 5HWXUQ 'LVFKDUJH )LOWHU 0RWRU
1
121(
121(
121(
:LWKRXW+RW:DWHU*HQHUDWRU
6WDQGDUG
121(
&
1
'
3
&RQWUROV
& &;0
NOTE: Above model nomenclature is a general reference. Consult individual speciÄcation catalogs
for detailed information.
1
50
2 3
4 5 6
7
8
9
10
YPS 026 N C C 3
11
12
1 1
Outdoor Splits
Prefix
Packaging
1 = Single Pack, Domestic
Series
YPS = Outdoor Split Residential
Revision Level
1 = Current Revision
Unit Size
026
038
049
064
Voltage
3 = 206-230/60/1
Heat Exchanger Options
Air Flow Configuration
C = Copper Coax
N = Cupro-Nickel Coax
N = NOT APPLICABLE
Controls
C = CXM
NOTE: Above model nomenclature is a general reference. Consult individual speciÄcation catalogs
for detailed information.
3
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Safety
Safety
Warnings, cautions and notices appear throughout this
manual. Read these items carefully before attempting any
installation, service, or troubleshooting of the equipment.
DANGER: Indicates an immediate hazardous situation, which
if not avoided will result in death or serious injury. DANGER
labels on unit access panels must be observed.
WARNING: Indicates a potentially hazardous situation, which
if not avoided could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation or an
unsafe practice, which if not avoided could result in minor or
moderate injury or product or property damage.
NOTICE: Noti¿cation of installation, operation or maintenance
information, which is important, but which is not hazardrelated.
ѥWARNING! ѥ
WARNING! To avoid the release of refrigerant into the
atmosphere, the refrigerant circuit of this unit must be
serviced only by technicians who meet local, state, and
federal pro¿ciency requirements.
4
ѥWARNING! ѥ
WARNING! All refrigerant discharged from this unit must
be recovered WITHOUT EXCEPTION. Technicians must
follow industry accepted guidelines and all local, state,
and federal statutes for the recovery and disposal of
refrigerants. If a compressor is removed from this unit,
refrigerant circuit oil will remain in the compressor. To
avoid leakage of compressor oil, refrigerant lines of the
compressor must be sealed after it is removed.
ѥCAUTION! ѥ
CAUTION! To avoid equipment damage, DO NOT use
these units as a source of heating or cooling during the
construction process. The mechanical components and
¿lters will quickly become clogged with construction dirt
and debris, which may cause system damage.
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
General Information
Storage
Pre-Installation
Inspection
Upon receipt of the equipment, carefully check the shipment
against the bill of lading. Make sure all units have been
received. Inspect the packaging of each unit, and inspect each
unit for damage. Insure that the carrier makes proper notation
of any shortages or damage on all copies of the freight bill
and completes a common carrier inspection report. Concealed
damage not discovered during unloading must be reported
to the carrier within 15 days of receipt of shipment. If not ¿led
within 15 days, the freight company can deny the claim without
recourse. Note: It is the responsibility of the purchaser to ¿le
all necessary claims with the carrier. Notify your equipment
supplier of all damage within ¿fteen (15) days of shipment.
Storage
Equipment should be stored in its original packaging in a
clean, dry area. Store units in an upright position at all times.
Stack units a maximum of 3 units high.
ѥCAUTION! ѥ
CAUTION! DO NOT store or install units in corrosive
environments or in locations subject to temperature or
humidity extremes (e.g., attics, garages, rooftops, etc.).
Corrosive conditions and high temperature or humidity can
signi¿cantly reduce performance, reliability, and service
life. Always move and store units in an upright position.
Tilting units on their sides may cause equipment damage.
ѥCAUTION! ѥ
CAUTION! CUT HAZARD - Failure to follow this caution
may result in personal injury. Sheet metal parts may have
sharp edges or burrs. Use care and wear appropriate
protective clothing, safety glasses and gloves when
handling parts and servicing heat pumps.
Unit Protection
Cover units on the job site with either the original packaging
or an equivalent protective covering. Cap the open ends of
pipes stored on the job site. In areas where painting, plastering,
and/or spraying has not been completed, all due precautions
must be taken to avoid physical damage to the units and
contamination by foreign material. Physical damage and
contamination may prevent proper start-up and may result in
costly equipment clean-up.
Examine all pipes, ¿ttings, and valves before installing any of
the system components. Remove any dirt or debris found in
or on these components.
Pre-Installation
Installation, Operation, and Maintenance instructions are
provided with each unit. Horizontal equipment is designed for
installation above false ceiling or in a ceiling plenum. Other
unit con¿gurations are typically installed in a mechanical
room. The installation site chosen should include adequate
service clearance around the unit. Before unit start-up,
read all manuals and become familiar with the unit and its
operation. Thoroughly check the system before operation.
Prepare units for installation as follows:
1. Compare the electrical data on the unit nameplate with
ordering and shipping information to verify that the
correct unit has been shipped.
2. Keep the cabinet covered with the original packaging
until installation is complete and all plastering, painting,
etc. is ¿nished.
3. Verify refrigerant tubing is free of kinks or dents and that
it does not touch other unit components.
4. Inspect all electrical connections. Connections must be
clean and tight at the terminals.
5. Locate and verify any hot water generator (HWG) or
other accessory kit located in the compressor section.
5
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Equipment Selection
Air Coil Match-ups
The installation of geothermal heat pump units and all
associated components, parts, and accessories which make
up the installation shall be in accordance with the regulations
of ALL authorities having jurisdiction and MUST conform to
all applicable codes. It is the responsibility of the installing
contractor to determine and comply with ALL applicable
codes and regulations.
General
Proper indoor coil selection is critical to system efÄciency.
Using an older-model coil can affect efÄciency and may
not provide the customer with rated or advertised EER
and COP. Coil design and technology have dramatically
improved operating efÄciency and capacity in the past 20
years. Homeowners using an older coil are not reaping these
cost savings and comfort beneÄts. NEVER MATCH AN R-22
INDOOR COIL WITH A PURON® COMPRESSOR SECTION.
Indoor Coil Selection - GT-PX & GT-PE (50YDS & YPS)
Split system heat pumps are rated in the AHRI directory with
a speciÄc indoor coil match. GT-PX and GT-PE models are
rated with Carrier/Bryant FV4 or FE4 series variable speed
air handlers as shown in Table 1a. Other brands of air
handlers may attain the same AHRI ratings providing that the
speciÄcations meet or exceed those listed in Table 1a AND
Table 1b. An ECM motor and TXV is required. Cap tubes
and Äxed oriÄces are not acceptable. PSC fans may be
used if matched to Table 1c, but will not meet AHRI ratings.
If using PSC fan, compressor section must be operated
as a single stage unit (i.e. wired for either 1st stage or 2nd
stage). Without the ability to vary the airÅow, supply air
temperatures may not be acceptable if the compressor is
allowed to change stages when used with a PSC fan motor.
Newer indoor coils have a larger surface area, enhanced Än
design, and grooved tubing. These features provide a larger
area for heat transfer, improving efÄciency and expanding
capacity. Typical older coils may only have one-third to onehalf the face area of these redesigned coils.
Table 1a: GT-PX & GT-PE Carrier/Bryant Air Handler Matches for AHRI Ratings
Compressor Section
026
038
049
064
Air Handler
Model FV4
003
005
006
006
A
3 - 14.5
7.42
A
3 - 14.5
7.42
Refrigerant
Puron®
Metering Device
Air Coil
Type
Rows - Fins/in.
Face Area (sq. ft.)
Cabinet ConÄguration
ECM Settings for
AHRI Ratings
(FV4 Fan Coil)
Fan Motor Type - HP
6
TXV (required)
Slope
3 - 14.5
3.46
A
3 - 14.5
5.93
UpÅow/DownÅow/Horizontal (Multipoise)
AC/HP size: 036
System Type:
Comfort AC/HP
CFM Adjust: Nom
AC/HP size: 036
System Type:
HP-EfÄc AC/HP
CFM Adjust: High
AC/HP size: 048
System Type:
Comfort AC/HP
CFM Adjust: High
AC/HP size: 060
System Type:
Comfort AC/HP
CFM Adjust: High
ECM - 1/2
ECM - 1/2
ECM - 3/4
ECM - 3/4
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Equipment Selection
Air Coil Match-ups
Table 1b: GT-PX & GT-PE Air Handler Characteristics for Brands other than Above Models
Nominal
Tons*
Evaporator
Temp (ºF)
CFM
Capacity
(MBtuh)**
026 - Part Load
1.5
50
530
19.2 - 22.4
026 - Full Load
2.0
52
880
24.2 - 28.2
038 - Part Load
2.5
51
700
25.2 - 29.2
038 - Full Load
3.0
50
1200
34.5 - 40.1
049 - Part Load
3.5
47
1000
34.3 - 39.9
049 - Full Load
4.0
48
1650
46.3 - 53.8
064 - Full Load
5.0
48
1850
54.5 - 63.3
Model*
* Nominal tons are at AHRI/ISO 13256-1 GLHP conditions. Two-stage units may be operated in single-stage mode if desired, where smaller
capacity is required. For example, a model 026 may be used as a 1-1/2 ton unit if “locked” into 1st stage operation only. If PSC fan is
used, unit must be “locked” into either 1st or 2nd stage. An ECM fan is required for two-stage operation and for AHRI ratings. Size air
handler for “Full Load” if operating in two-stage mode.
**When selecting an air handler based upon the above conditions, choose entering WB temperature of 67ºF. Use evaporator temperature,
CFM and capacity requirements as listed above. The air handler capacity must be at least at the minimum capacity shown in the table in
order for the AHRI rating condition to be valid. See Figure 1 for an example selection.
Note: Due to limitations in combining a geothermal split unit with a Bryant Evolution fan coil, furnace and InÄnity
control, or a Bryant Evolution fan coil, furnace and Evolution controller, refer to Service Bulletins SMB 10-0007 and
DSB 10-0007.
7
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Equipment Selection
Air Handler Selection
Air Handler Selection Example
Figure 1 shows a typical performance table for a heat pump
air handler. Suppose the evaporator temperature required
is 50ºF, the capacity required is 35,000 Btuh and the airÅow
required is 1,200 CFM. Each evaporator temperature
listed in the table shows three wet bulb temperatures. As
recommended in the table notes above, select the 67ºF
WB column. At 1,200 CFM, the model 003 capacity is 36
MBtuh, which is higher than the minimum capacity required
of 35,000 Btuh. In this example, model 003 would be the
appropriate match.
Figure 1: Selecting Air Handler
Coil Refrigerant Temperatre (°F)*
Unit
Size
003
005
006
50
55
72
67
62
72
67
62
72
67
62
72
67
62
72
67
62
800
59
48
38
53
42
32
46
35
24
39
27
20
30
18
16
Evaporator Air - Entering Wet-Bulb Temperature (°F)
0.20
28
29
31
25
27
28
22
23
24
19
20
20
16
16
16
1000
68
56
45
61
49
37
54
41
29
45
32
25
35
22
20
0.22
1200
32
75
34
62
37
49
29
68
31
54
33
42
26
60
28
45
28
34
23
50
24
36
25
29
19
40
20
25
20
23
0.25
35
39
42
32
36
28
29
32
33
26
28
29
22
23
23
1400
0.27
750
80
28
61
67
43
49
54
47
39
73
35
55
59
39
43
46
43
33
64
32
48
49
36
37
38
37
27
54
28
41
39
32
29
32
32
20
43
24
33
28
26
21
27
27
17
0.04
27
27
28
24
25
25
21
22
22
18
18
18
15
15
15
950
74
60
48
67
53
40
59
45
33
50
35
25
39
24
21
0.06
32
34
35
29
30
31
25
26
27
22
23
23
18
18
19
1150
0.07
1500
89
37
103
72
39
84
57
41
66
79
33
92
63
35
73
48
36
56
69
29
81
52
31
61
38
32
46
58
25
67
41
25
48
31
27
39
44
20
52
29
22
34
25
22
31
0.10
43
46
49
38
41
44
34
37
39
29
32
33
25
27
27
1700
0.11
1050
0.01
110
45
77
34
89
50
62
36
71
53
50
37
99
41
69
31
78
45
55
32
60
48
43
33
86
36
61
27
65
39
47
28
49
42
32
29
72
31
52
23
51
34
38
25
42
36
27
24
56
27
41
20
37
29
27
20
35
30
22
20
1300
100
82
65
90
71
55
79
60
45
66
47
37
49
32
27
0.02
42
45
47
37
40
42
33
35
37
29
31
32
23
25
24
1750
117
96
77
106
84
65
93
71
53
78
56
46
60
40
34
0.04
2050
0.05
2300
48
126
52
132
53
103
58
108
57
83
63
87
44
114
48
119
48
91
53
95
52
71
57
75
39
99
43
105
43
76
47
80
46
59
51
63
34
84
37
88
38
60
42
63
39
50
43
54
29
65
33
70
31
44
35
47
31
39
35
42
0.06
55
62
58
50
57
61
45
51
54
40
45
46
35
39
38
= Gross cooling capacity (MBtuh)
= Sensible heat capacity (MBtuh)
BF = Bypass Factor
8
45
40
35
Evaporator
Air CFM
BF
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Installation
The installation of water source heat pump units and all
associated components, parts and accessories which make
up the installation shall be in accordance with the regulations
of ALL authorities having jurisdiction and MUST conform to
all applicable codes. It is the responsibility of the installing
contractor to determine and comply with ALL applicable
codes and regulations.
Removing Existing Condensing Unit (Where Applicable)
1. Pump down condensing unit. Close the liquid line
service valve of existing condensing unit and start
compressor to pump refrigerant back into compressor
section. Then, close suction service valve while
compressor is still running to trap refrigerant in outdoor
section. Immediately kill power to the condensing unit.
2. Disconnect power and low voltage and remove old
condensing unit. Cut or unbraze line set from unit.
Remove condensing unit.
3. If condensing unit is not operational or will not pump
down, refrigerant should be recovered using appropriate
equipment.
4. Replace line set, especially if upgrading system from
R-22 to Puron® refrigerant. If line set cannot be replaced,
it must be thoroughly Åushed before installing new
compressor section. Puron® compressors use POE
oil instead of mineral oil (R-22 systems). Mineral oil is
not compatible with POE oil, and could cause system
damage if not completely Åushed from the line set.
“Indoor” Compressor Section Location
Both “indoor” and “outdoor” versions of the geothermal
split system compressor section are available. “Indoor”
version is not designed for outdoor installation. Locate the
unit in an INDOOR area that allows enough space for service
personnel to perform typical maintenance or repairs without
removing unit. Units are typically installed in a mechanical
room or closet. Never install units in areas subject to freezing
or where humidity levels could cause cabinet condensation
(such as unconditioned spaces subject to 100% outside air).
Consideration should be given to access for easy removal
of service access panels. Provide sufÄcient room to make
water, electrical, and line set connections.
3. Provide access for servicing the compressor and coils
without removing the unit.
4. Provide an unobstructed path to the unit within the
closet or mechanical room. Space should be sufÄcient to
allow removal of the unit, if necessary.
5. Provide access to water valves and Ättings and
screwdriver access to the unit side panels and all
electrical connections.
“Outdoor” Compressor Section Location
Locate the unit in an outdoor area that allows easy loop
and lineset access and also has enough space for service
personnel to perform typical maintenance or repairs. The
“outdoor” compressor section is usually installed on a
condenser pad directly outside the lineset access into the
building. The loop access end should be located away from
the building. Conform to the following guidelines when
selecting unit location:
1. Provide adequate access for loop trench excavation.
2. Locate unit directly outside lineset penetration if
possible. Utilize existing condensor pad where
possible.
3. Provide access for servicing and maintenance.
“Outdoor” compressor section may be mounted on a
vibration isolation pad with loop access hole as shown
in Figure 3. When mounting on an existing concrete
condenser pad, 3” [76 mm] holes should be bored through
the pad to accommodate the pipe (1-¼” - 32mm) and
insulation (½” [13mm] wall thickness). Figure 3 illustrates
location and dimensions of the holes required.
Air Handler Installation
This manual speciÄcally addresses the compressor section
of the system. Air handler location and installation should
be according to the instructions provided with the air
handling unit.
Any access panel screws that would be difÄcult to remove
after the unit is installed should be removed prior to setting
the unit. Refer to Figure 2 for an illustration of a typical
installation. Refer to “Physical Dimensions” section for
dimensional data. Conform to the following guidelines when
selecting unit location:
1. Install the unit on a piece of rubber, neoprene or other
mounting pad material for sound isolation. The pad should
be at least 3/8” [10mm] to 1/2” [13mm] in thickness.
Extend the pad beyond all four edges of the unit.
2. Provide adequate clearance for maintenance and
service. Do not block access panels with piping, conduit
or other materials.
9
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Installation
Figure 2: GT-PX Installation
Figure 3: GT-PE Installation
([LVWLQJ3DGODUJHUWKDQ[>[FP@
%RWWRP9LHZ
RI8QLW
µ[µ
[FP
µ
>FP@
$LU3DG:LWK
$FFHVV+ROH
µ>FP@
µ
>FP@
External Flow Controller Mounting
The Flow Controller can be mounted beside the indoor unit
as shown in Figure 7. Review the Flow Controller installation
manual for more details.
µ
>FP@
The female locking ring is threaded onto the pipe threads
which holds the male pipe end against the rubber gasket,
and seals the joint. HAND TIGHTEN ONLY! DO NOT
OVERTIGHTEN!
Figure 4: Water Connections (50YDS Models)
(50YDS Models)
Water Connections-Residential (Distributor)
Models
Residential models utilize swivel piping Ättings for water
connections that are rated for 450 psi (3101 kPa) operating
pressure. The connections have a rubber gasket seal
similar to a garden hose gasket, which when mated to the
Åush end of most 1” threaded male pipe Ättings provides
a leak-free seal without the need for thread sealing tape or
joint compound. Insure that the rubber seal is in the swivel
connector prior to attempting any connection (rubber seals
are shipped attached to the swivel connector). DO NOT
OVER TIGHTEN or leaks may occur.
10
Swivel Nut
Stainless steel
snap ring
Hand Tighten
Only!
Do Not
Overtighten!
Gasket
Brass Adaptor
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Installation
Internal Flow Controller Connections (50YPS Series)
The 50YPS series outdoor compressor section includes a
factory built-in circulator, as shown in Ägure 3.
Figure 5: Hose Connections (GT-PE Series)
The circulator in the 50YPS unit is three speed (shipped on
high speed). Lower circulator speeds may be chosen where
appropriate to lower pumping power and match the Åow rate
to the unit’s requirements. The pump speed selection switch
is located on the pump’s electrical box.
50YPS026 and 038 units come standard with one
circulator. 50YPS049 and 064 units come standard with
two circulators, piped in series for greater Åow and head
capabilities.
6WDLQOHVV6WHHO
%UDLGHG&RQQHFWLQJ
+RVHV
$LU3DG:LWK
$FFHVV+ROH
50YPS026 and 038 units are shipped with ¾” stainless
steel braided hoses connected to unit piping. These hoses
terminate in swivel connections.
50YPS049 and 064 units are shipped with 1” stainless
steel braided hoses connected to unit piping. These hoses
terminate in swivel connections.
ѥCAUTION! ѥ
ѥCAUTION! ѥ
CAUTION! To avoid equipment damage, DO NOT allow
system water pressure to exceed 100 psi when using
the GT-PE Outdoor Compressor Section. The expansion
tank in the GT-PE has a maximum working water
pressure of 100 psi. Any pressure in excess of 100 psi
may damage the expansion tank.
CAUTION! Using check valves in GT-PE (50YPS) units
will prevent thermo siphoning of the ground loop. If the unit
loses power this may cause the coaxial heat exchanger
to freeze if the ambient temperature falls below the freeze
point of the ground loop Àuid.
Figure 6: Pump Curves for GT-PE internal pump(s) - Single Pump
35.0
30.0
25.0
Head (ft)
20.0
Speed 3
15.0
Speed 2
10.0
Speed 1
5.0
0.0
0
5
10
15
GPM
20
25
30
35
Double Pump Table on following page
11
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Installation
Figure 6: Pump Curves for GT-PE internal pump(s) - Double Pump
70
60
Head (ft)
50
40
Speed 3
30
Speed 2
20
Speed 1
10
0
0
5
10
15
20
25
30
GPM
Ground-Loop Heat Pump Applications
ѥCAUTION! ѥ
CAUTION! The following instructions represent industry
accepted installation practices for closed loop earth
coupled heat pump systems. Instructions are provided
to assist the contractor in installing trouble free ground
loops. These instructions are recommendations only.
State/provincial and local codes MUST be followed and
installation MUST conform to ALL applicable codes. It is
the responsibility of the installing contractor to determine
and comply with ALL applicable codes and regulations.
12
Pre-Installation
Prior to installation, locate and mark all existing underground
utilities, piping, etc. Install loops for new construction before
sidewalks, patios, driveways, and other construction has
begun. During construction, accurately mark all ground loop
piping on the plot plan as an aid in avoiding potential future
damage to the installation.
Piping Installation
The typical closed loop ground source system is shown in
Figure 7. All earth loop piping materials should be limited
to polyethylene fusion only for in-ground sections of the
loop. Galvanized or steel Ättings should not be used at any
time due to their tendency to corrode. All plastic to metal
threaded Ättings should be avoided due to their potential to
leak in earth coupled applications. A Åanged Ätting should
be substituted. P/T plugs should be used so that Åow
can be measured using the pressure drop of the unit heat
exchanger.
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Ground-Loop Heat Pump Applications
Earth loop temperatures can range between 25 and
110°F [-4 to 43°C]. Flow rates between 2.25 and 3 gpm
per ton [2.41 to 3.23 l/m per kW] of cooling capacity is
recommended in these applications.
Test individual horizontal loop circuits before backÄlling.
Test vertical U-bends and pond loop assemblies prior to
installation. Pressures of at least 100 psi [689 kPa] should be
used when testing. Do not exceed the pipe pressure rating.
Test entire system when all loops are assembled.
Flushing the Earth Loop
Once piping is completed between the unit, Flow Controller
and the ground loop (Figure 7), the loop is ready for Änal
purging and charging. A Åush cart with at least a 1.5 hp
[1.1 kW] pump is required to achieve enough Åuid velocity
in the loop piping system to purge air and dirt particles. An
antifreeze solution is used in most areas to prevent freezing.
All air and debris must be removed from the earth loop
piping before operation. Flush the loop with a high volume
of water at a minimum velocity of 2 fps (0.6 m/s) in all piping.
The steps below must be followed for proper Åushing.
1. Fill loop with water from a garden hose through the Åush
cart before using the Åush cart pump to insure an even
Äll.
2. Once full, the Åushing process can begin. Do not allow
the water level in the Åush cart tank to drop below the
pump inlet line to avoid air being pumped back out to
the earth loop.
3. Try to maintain a Åuid level in the tank above the return
tee so that air cannot be continuously mixed back into
the Åuid. Surges of 50 psi (345 kPa) can be used to help
purge air pockets by simply shutting off the return valve
going into the Åush cart reservoir. This “dead heads”
the pump to 50 psi (345 kPa). To purge, dead head the
pump until maximum pumping pressure is reached.
Open the return valve and a pressure surge will be sent
through the loop to help purge air pockets from the
piping system.
4. Notice the drop in Åuid level in the Åush cart tank when
the return valve is shut off. If air is adequately purged
from the system, the level will drop only 1-2 inches (2.5
- 5 cm) in a 10” (25 cm) diameter PVC Åush tank (about a
half gallon [2.3 liters]), since liquids are incompressible. If
the level drops more than this, Åushing should continue
since air is still being compressed in the loop Åuid.
Perform the “dead head” procedure a number of times.
Note: This Åuid level drop is your only indication of air in
the loop.
Antifreeze may be added before, during or after the Åushing
procedure. However, depending upon which time is chosen,
antifreeze could be wasted when emptying the Åush cart
tank. See antifreeze section for more details.
Loop static pressure will Åuctuate with the seasons.
Pressures will be higher in the winter months than during
the cooling season. This Åuctuation is normal and should
be considered when charging the system initially. Run the
unit in either heating or cooling for a number of minutes to
condition the loop to a homogenous temperature. This is
a good time for tool cleanup, piping insulation, etc. Then,
perform Änal Åush and pressurize the loop to a static
pressure of 50-75 psi [345-517 kPa] (winter) or 35-40 psi
[241-276 kPa] (summer). After pressurization, be sure to
loosen the plug at the end of the Grundfos loop pump
motor(s) to allow trapped air to be discharged and to insure
the motor housing has been Åooded. This is not required
for Taco circulators. Insure that the Flow Controller provides
adequate Åow through the unit by checking pressure drop
across the heat exchanger and compare to the pressure
drop tables at the back of the manual.
ѥCAUTION! ѥ
CAUTION! To avoid equipment damage, DO NOT allow
system water pressure to exceed 100 psi when using
the GT-PE Outdoor Compressor Section. The expansion
tank in the GT-PE has a maximum working water
pressure of 100 psi. Any pressure in excess of 100 psi
may damage the expansion tank.
Antifreeze
In areas where minimum entering loop temperatures drop
below 40°F [5°C] or where piping will be routed through
areas subject to freezing, antifreeze is required. Alcohols
and glycols are commonly used as antifreeze; however your
local sales manager should be consulted for the antifreeze
best suited to your area. Low temperature protection
should be maintained to 15°F [9°C] below the lowest
expected entering loop temperature. For example, if 30°F
[-1°C] is the minimum expected entering loop temperature,
the leaving loop temperature would be 25 to 22°F [-4 to
-6°C] and low temperature protection should be at 15°F
[-10°C]. Calculation is as follows:
30°F - 15°F = 15°F [-1°C - 9°C = -10°C].
All alcohols should be premixed and pumped from a
reservoir outside of the building when possible or introduced
under the water level to prevent fumes. Calculate the
total volume of Åuid in the piping system. Then use the
percentage by volume shown in Table 3 for the amount
of antifreeze needed. Antifreeze concentration should be
checked from a well mixed sample using a hydrometer to
measure speciÄc gravity.
Low Water Temperature Cutout Setting - CXM Control
When antifreeze is selected, the FP1 jumper (JW3) should
be clipped to select the low temperature (antifreeze 10°F
[-12.2°C]) set point and avoid nuisance faults (see “Low
Water Temperature Cutout Selection” in this manual). Note:
Low water temperature operation requires extended range
equipment.
13
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Ground-Loop Heat Pump Applications
Table 2: Approximate Fluid Volume (U.S. gal. [L]) per
100' of Pipe
Figure 7: Loop Connection (Indoor
Compressor Section)
Fluid Volume (gal [liters] per 100’ [30 meters) Pipe)
Pipe
Copper
Rubber Hose
Polyethylene
Size
Volume (gal) [liters]
1”
4.1 [15.3]
1.25”
6.4 [23.8]
2.5”
9.2 [34.3]
1”
3.9 [14.6]
3/4” IPS SDR11
2.8 [10.4]
1” iPS SDR11
4.5 [16.7]
1.25” IPS SDR11
8.0 [29.8]
1.5” IPS SDR11
10.9 [40.7]
2” IPS SDR11
18.0 [67.0]
1.25” IPS SCH40
8.3 [30.9]
1.5” IPS SCH40
10.9 [40.7]
2” IPS SCH40
17.0 [63.4]
Unit Heat Exchanger
Typical
1.0 [3.8]
Flush Cart Tank
10” Dia x 3ft tall
[254mm x 91.4cm tall]
10 [37.9]
To Loop
Flow
Controller
Unit Power
Disconnect
Insulated
Hose Kit
AH & Thermostat
Wiring
Air Pad or
Extruded
polystyrene
insulation board
P/T Plugs
Table 3: Antifreeze Percentages by Volume
Type
Minimum Temperature for Low Temperature Protection
10°F [-12.2°C]
15°F [-9.4°C]
20°F [-6.7°C]
25°F [-3.9°C]
25%
38%
29%
21%
25%
25%
16%
22%
20%
10%
15%
14%
Methanol
100% USP food grade Propylene Glycol
Ethanol*
* Must not be denatured with any petroleum based product
14
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Ground-Water Heat Pump Applications “Indoor” Compressor Section Only
Open Loop - Ground Water Systems
Typical open loop piping is shown in Figure 8. Shut off valves
should be included for ease of servicing. Boiler drains or other
valves should be “tee’d” into the lines to allow acid Åushing
of the heat exchanger. Shut off valves should be positioned
to allow Åow through the coax via the boiler drains without
allowing Åow into the piping system. P/T plugs should be
used so that pressure drop and temperature can be measured.
Piping materials should be limited to copper or PVC SCH80.
Note: Due to the pressure and temperature extremes, PVC
SCH40 is not recommended.
Water quantity should be plentiful and of good quality.
Consult Table 4 for water quality guidelines. The unit can
be ordered with either a copper or cupro-nickel water
heat exchanger. Consult Table 4 for recommendations.
Copper is recommended for closed loop systems and open
loop ground water systems that are not high in mineral
content or corrosiveness. In conditions anticipating heavy
scale formation or in brackish water, a cupro-nickel heat
exchanger is recommended. In ground water situations
where scaling could be heavy or where biological growth
such as iron bacteria will be present, an open loop system
is not recommended. Heat exchanger coils may over time
lose heat exchange capabilities due to build up of mineral
deposits. Heat exchangers must only be serviced by a
qualiÄed technician, as acid and special pumping equipment
is required. Desuperheater coils can likewise become scaled
and possibly plugged. In areas with extremely hard water,
the owner should be informed that the heat exchanger
may require occasional acid Åushing. In some cases, the
desuperheater option should not be recommended due to
hard water conditions and additional maintenance required.
Water Quality Standards
Table 4 should be consulted for water quality requirements.
Scaling potential should be assessed using the pH/Calcium
hardness method. If the pH <7.5 and the Calcium hardness
is less than 100 ppm, scaling potential is low. If this method
yields numbers out of range of those listed, the Ryznar
Stability and Langelier Saturation indecies should be
calculated. Use the appropriate scaling surface temperature
for the application, 150°F [66°C] for direct use (well water/
open loop) and DHW (desuperheater); 90°F [32°F] for
indirect use. A monitoring plan should be implemented in
these probable scaling situations. Other water quality issues
such as iron fouling, corrosion prevention and erosion and
clogging should be referenced in Table 4.
Expansion Tank and Pump
Use a closed, bladder-type expansion tank to minimize
mineral formation due to air exposure. The expansion tank
should be sized to provide at least one minute continuous
run time of the pump using its drawdown capacity rating to
prevent pump short cycling. Discharge water from the unit
is not contaminated in any manner and can be disposed
of in various ways, depending on local building codes (e.g.
recharge well, storm sewer, drain Äeld, adjacent stream
or pond, etc.). Most local codes forbid the use of sanitary
sewer for disposal. Consult your local building and zoning
department to assure compliance in your area.
The pump should be sized to handle the home’s domestic
water load (typically 5-9 gpm [23-41 l/m]) plus the Åow rate
required for the heat pump. Pump sizing and expansion
tank must be chosen as complimentary items. For example,
an expansion tank that is too small can causing premature
pump failure due to short cycling. Variable speed pumping
applications should be considered for the inherent energy
savings and smaller expansion tank requirements.
Water Control Valve
Note the placement of the water control valve in Ägure 8.
Always maintain water pressure in the heat exchanger by
placing the water control valve(s) on the discharge line
to prevent mineral precipitation during the off-cycle. Pilot
operated slow closing valves are recommended to reduce
water hammer. If water hammer persists, a mini-expansion
tank can be mounted on the piping to help absorb the
excess hammer shock. Insure that the total ‘VA’ draw of the
valve can be supplied by the unit transformer. For instance,
a slow closing valve can draw up to 35VA. This can overload
smaller 40 or 50 VA transformers depending on the other
controls in the circuit. A typical pilot operated solenoid valve
draws approximately 15VA (see Figure 24). Note the special
wiring diagrams for slow closing valves (Figures 25 & 26).
Flow Regulation
Flow regulation can be accomplished by two methods. One
method of Åow regulation involves simply adjusting the ball
valve or water control valve on the discharge line. Measure
the pressure drop through the unit heat exchanger, and
determine Åow rate from Table 14. Since the pressure is
constantly varying, two pressure gauges may be needed.
Adjust the valve until the desired Åow of 1.5 to 2 gpm per
ton [2.0 to 2.6 l/m per kW] is achieved. A second method
of Åow control requires a Åow control device mounted on
the outlet of the water control valve. The device is typically
a brass Ätting with an oriÄce of rubber or plastic material
that is designed to allow a speciÄed Åow rate. On occasion,
Åow control devices may produce velocity noise that can be
reduced by applying some back pressure from the ball valve
located on the discharge line. Slightly closing the valve will
spread the pressure drop over both devices, lessening the
velocity noise. NOTE: When EWT is below 50°F [10°C], a
minimum of 2 gpm per ton (2.6 l/m per kW) is required.
ѥCAUTION! ѥ
CAUTION! To avoid equipment damage, DO NOT allow
system water pressure to exceed 100 psi when using
the GT-PE Outdoor Compressor Section. The expansion
tank in the GT-PE has a maximum working water
pressure of 100 psi. Any pressure in excess of 100 psi
may damage the expansion tank.
15
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Ground-Water Heat Pump Applications
Water Coil Low Temperature Limit Setting
For all open loop systems the 30°F [-1.1°C] FP1 setting
(factory setting-water) should be used to avoid freeze damage
to the unit. See “Low Water Temperature Cutout Selection” in
this manual for details on the low limit setting.
Figure 8: Water Well Connections
Flow
Water
Regulator
Control
Valve
ѥCAUTION! ѥ
CAUTION! Many units are installed with a factory or ¿eld
supplied manual or electric shut-off valve. DAMAGE WILL
OCCUR if shut-off valve is closed during unit operation. A
high pressure switch must be installed on the heat pump
side of any ¿eld provided shut-off valves and connected to
the heat pump controls in series with the built-in refrigerant
circuit high pressure switch to disable compressor
operation if water pressure exceeds pressure switch
setting. The ¿eld installed high pressure switch shall have
a cut-out pressure of 300 psig and a cut-in pressure of
250 psig. This pressure switch can be ordered with a 1/4”
internal Àare connection as part number 39B0005N02.
ѥCAUTION! ѥ
CAUTION! Refrigerant pressure activated water regulating
valves should never be used with the equipment.
16
Pressure
Tank
Water Out
Shut-Off
Valve
Optional
Filter
P/T Plugs
Boiler
Drains
Water In
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Water Quality Standards
Table 4: Water Quality Standards
Water Quality
Parameter
HX
Material
Closed
Recirculating
Open Loop and Recirculating Well
Scaling Potential - Primary Measurement
Above the given limits, scaling is likely to occur. Scaling indexes should be calculated using the limits below
pH/Calcium Hardness
Method
All
-
pH < 7.5 and Ca Hardness <100ppm
Index Limits for Probable Scaling Situations - (Operation outside these limits is not recommended)
Scaling indexes should be calculated at 66°C for direct use and HWG applications, and at 32°C for indirect HX use.
A monitoring plan should be implemented.
Ryznar
6.0 - 7.5
All
Stability Index
If >7.5 minimize steel pipe use.
-0.5 to +0.5
Langelier
All
If <-0.5 minimize steel pipe use. Based upon 66°C HWG and
Saturation Index
Direct well, 29°C Indirect Well HX
Iron Fouling
Iron Fe 2+ (Ferrous)
(Bacterial Iron potential)
All
Iron Fouling
All
-
<0.2 ppm (Ferrous)
If Fe2+ (ferrous)>0.2 ppm with pH 6 - 8, O2<5 ppm check for iron bacteria.
-
<0.5 ppm of Oxygen
Above this level deposition will occur .
Corrosion Prevention
6 - 8.5
pH
All
Hydrogen Sulfide (H2S)
All
Ammonia ion as hydroxide, chloride,
nitrate and sulfate compounds
All
Monitor/treat as
needed
-
6 - 8.5
Minimize steel pipe below 7 and no open tanks with pH <8
<0.5 ppm
At H2S>0.2 ppm, avoid use of copper and copper nickel piping or HX's.
Rotten egg smell appears at 0.5 ppm level.
Copper alloy (bronze or brass) cast components are OK to <0.5 ppm.
-
<0.5 ppm
Maximum Allowable at maximum water temperature.
Maximum
Chloride Levels
Copper
Cupronickel
304 SS
316 SS
Titanium
-
10$C
<20ppm
<150 ppm
<400 ppm
<1000 ppm
>1000 ppm
24$C
NR
NR
<250 ppm
<550 ppm
>550 ppm
38 C
NR
NR
<150 ppm
< 375 ppm
>375 ppm
Erosion and Clogging
Particulate Size and
Erosion
All
<10 ppm of particles
and a maximum
velocity of 1.8 m/s
Filtered for maximum
841 micron [0.84 mm,
20 mesh] size.
Notes:
‡&ORVHG5HFLUFXODWLQJV\VWHPLVLGHQWLILHGE\Dclosed pressurized piping system.
‡5HFLUFXODWLQJRSHQZHOOVVKRXOGREVHUYHWKHRSHQUHFLUFXODWLQJGHVLJQFRQVLGHUDWLRQV
‡15Application not recommended.
‡1RGHVLJQ0D[LPXP
<10 ppm (<1 ppm "sandfree” for reinjection) of particles and a maximum
velocity of 1.8 m/s. Filtered for maximum 841 micron 0.84 mm,
20 mesh] size. Any particulate that is not removed can potentially
clog components.
Rev.: 4/6/2011
17
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Refrigeration Installation
ѥCAUTION! ѥ
CAUTION! Puron® systems operate at higher pressures
than R-22 systems. Be certain that service equipment
(gauges, tools, etc.) is rated accordingly. Some R-22
service equipment may not be acceptable.
ѥCAUTION! ѥ
CAUTION! Installation of a factory supplied liquid line
bi-directional Älter drier is required. Never install a suction
line Älter in the liquid line.
Line Set Installation
Figures 11a and 11b illustrate typical installations of a
compressor section matched to either an air handler (fan coil) or
add-on furnace coil. Table 5 shows typical line-set diameters at
various lengths. Lineset lengths should be kept to a minimum
and should always be installed with care to avoid kinking. Line
sets over 60 feet [18 meters] long are not recommended due to
potential oil transport problems and excessive pressure drop. If
the line set is kinked or distorted, and it cannot be formed back
into its original shape, the damaged portion of the line should
be replaced. A restricted line set will effect the performance of
the system.
Split units are shipped with a Älter drier (loose) inside the
cabinet that must be installed in the liquid line at the line set.
All brazing should be performed using nitrogen circulating
at 2-3 psi [13.8-20.7 kPa] to prevent oxidation inside the
tubing. All linesets should be insulated with a minimum of
1/2” [13mm] thick closed cell insulation. Liquid lines should
be insulated for sound control purposes. All insulation
tubing should be sealed using a UV resistant paint or
covering to prevent deterioration from sunlight.
When passing refrigerant lines through a wall, seal
opening with silicon-based caulk. Avoid direct contact
with water pipes, duct work, Åoor joists, wall studs,
Åoors or other structural components that could transmit
compressor vibration. Do not suspend refrigerant tubing
from joists with rigid straps. Do not attach line set to the
wall. When necessary, use hanger straps with isolation
sleeves to minimize transmission of line set vibration to
the structure.
Installing the Lineset at the Compressor Section
Braze the line set to the service valve stubs as shown in Figure
9. Remove the schraeder cores and heat trap the valves to
avoid overheating and damage. On installations with long line
sets, copper adapters may be needed to connect the larger
diameter tube to the stubs. Nitrogen should be circulated
through the system at 2-3 psi [13.8-20.7 kPa] to prevent
oxidation contamination. Use a low silver phos-copper braze
alloy on all brazed connections. Compressor section is
shipped with a factory charge. Therefore, service valves
should not be opened until the line set has been leak
tested, purged and evacuated. See “Charging the System.”
Installing the Indoor Coil and Lineset
Figure 10 shows the installation of the lineset and TXV to a
typical indoor coil. An indoor coil or air handler (fan coil) with a
TXV is required. Coils with cap tubes may not be used. If coil
includes removable Äxed oriÄce, the oriÄce must be removed
and a TXV must be installed as shown in Figure 10. Fasten
the copper line set to the coil. Nitrogen should be circulated
through the system at 2-3 psi [13.8-20.7 kPa] to prevent
oxidation inside the refrigerant tubing. Use a low silver phoscopper braze alloy on all brazed connections.
Table 5: Lineset Diameters and Charge Information
Factory†
Charge (oz)
[kg]
Basic*
Charge (oz)
[kg]
20 Feet [6 meters]
40 Feet [12 meters]
60 Feet [18 meters]
Liquid
Liquid
Suction
Liquid
Suction
026
92 [2.61]
75 [2.13]
3/8”
7/8”
3/8”
7/8”
3/8”
7/8”
038
120 [3.40]
89 [2.52]
3/8”
7/8”
3/8”
7/8”
3/8”
7/8”
049
142 [4.02]
111 [3.15]
1/2”
7/8”
1/2”
7/8”
1/2”
7/8”
064
204 [5.78]
138 [3.91]
1/2”
7/8”
1/2”
7/8”
1/2”
7/8”
Model
Suction
TTS/TTP Series
50YDS/50YPS
Series
• Basic charge includes only the amount required for the condensing unit and the evaporating coil.
An additional amount should be added allowing 0.6oz per ft. for 3/8” [0.6g per cm] and 1.2oz per ft. for 1/2” [1.1g per cm] of lineset used.
†Factory charge is preset for 25’ [7.6 meters] lineset.
18
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Refrigeration Installation
Figure 9: Braze Instructions
Figure 10: Air Coil Connection
Bulb (Must be
Installed and
Insulated)
Fully Insulated
Vapor Line
Suction
Equalizer
Line
TXV (‘IN’ toward
compressor section)
FP2
Sensor
Suction Line
TXV has internal
check valve
Fully Insulated
Liquid Line
Liquid Line
Nitrogen Braze
Fully Insulated
Suction Line
ѥWARNING! ѥ
WARNING! If at all possible, it is recommended that a
new line set be used when replacing an existing R-22
system with an HFC-410A system. In rare instances
where replacing the line set is not possible, the line set
must be Åushed prior to installation of the HFC-410A
system. It is also important to empty all existing traps.
Polyolester (POE) oils are used in units charged with
HFC-410A refrigerant. Residual mineral oil can act as an
insulator on the wall of the coil tubing, hindering proper
heat transfer and thus reducing system efÄciency and
capacity. Another important reason to thoroughly Åush
the line set is remove any trash and other contaminants
that may be present which could clog the thermal
expansion valve.
Failure to properly Åush the system per the instructions
below will void the warranty.
Fully Insulated
Liquid Line
Nitrogen Braze
)XOO\,QVXODWHG
/LTXLG/LQH
ѥWARNING! ѥ
WARNING! The Environmental Protection Agency
prohibits the intentional venting of HCFC and HFC
refrigerants during maintenance, service, repair and
disposal of appliance. Approved methods of recovery,
recycling or reclaiming must be followed.
)XOO\,QVXODWHG
9DSRU/LQH
Table 6: Service Valve Positions
Position
Description
Operation Position
CCW - Full Out
CCW - Full Out 1/2 turn CW Service Position
CCW - Full In
Shipping Position
System
Service
Port
Open
Open
Closed
Closed
Open
Open
Re-Using Existing Line Set - R-22 to Puron® Conversion
New line sets are always recommended, but are required if;
• The previous system had a compressor burn out.
• The existing line set has oil traps.
• The existing line set is larger or smaller than the
recommended line set for the Puron® system.
• The existing line set is damaged, corroded, or shows signs
of abrasion/fatigue
ѥCAUTION! ѥ
CAUTION! This procedure should not be performed
on systems which contain containments (Example:
compressor burn out).
Required Equipment
The following equipment will be required in order to Åush the
indoor coil and existing line set:
• Two R-22 recovery cylinders
• Refrigerant recovery machine with a pump down feature
• Two sets of gauges (one used for R-22 and one used with
Puron®.
• Cylinder of clean R-22 (minimum amount required to
adequately Åush shown below)
19
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Refrigeration Installation
• 3/4” diameter suction lines: 1/4 lb. per foot of line set +
1 lb. per ton for indoor coil.
• 7/8” diameter suction lines: 1/3 lb. per foot of line set +
1 lb. per ton for indoor coil
• 1-1/8” diameter suction lines: 1/2 lb. per foot of line set
+ 1 lb. per ton for indoor coil.
Example: 3-ton system with 40 ft. long line set and 3/4”
suction line.
Line set: 1/4 lb./ft. x 40 ft. = 10 lb.
Indoor coil: 1 lb./ton x 3 tons = 3 lbs. (not required if coil
is removed and lines are connected together)
Total: 10 lbs. + 3 lbs. = 13 lbs. to adequately Åush line
set and indoor coil.
The Flushing Procedure
1. Remove the existing R-22 refrigerant by selecting the
appropriate procedure stated below.
If the unit is not operational, follow steps A-E.
• A.) First, disconnect all power supply to the existing
outdoor unit.
• B.) Connect a clean refrigerant recovery cylinder and
the refrigerant recovery machine to the existing unit
according to the instructions provided with the recovery
machine.
• C.) Remove all R-22 refrigerant from the existing system.
• D.) Check the gauges after shutdown to conÄrm all
refrigerant has been completely removed from the entire
system.
• E.) Disconnect the liquid and vapor lines from the
existing outdoor unit.
2.
3.
4.
5.
6.
20
If the unit is operational, follow steps F- L.
• F.) First, start the existing R-22 system in the cooling
mode and close the liquid line valve.
• G.) Completely pump all existing R-22 refrigerant into
the outdoor unit. It will be necessary to bypass the low
pressure switch if the unit is so equipped to ensure that
the refrigerant is completely evacuated.)
• H.) The low side system pressures will eventually reach 0
psig. When this happens, close the vapor line valve and
immediately shut the outdoor unit off.
• I.) Check the gauges after shutdown to conÄrm that the
valves are not allowing refrigerant to leak back into the
low side of the system.
• J.) Disconnect power to the indoor furnace or airhandler to kill low voltage to the outdoor unit.
• K.) Disconnect the power supply wiring from the
existing outdoor unit.
• L.) Unsweat the liquid and vapor lines from the existing
outdoor unit.
Remove the existing outdoor unit.
Set the new Puron® unit in place and braze the liquid
and vapor lines to the unit connections. Connect the low
voltage and line voltage to the new outdoor unit. Do not
turn on power supply to the unit and do not open the
outdoor unit service valves at this time.
The indoor coil can be left in place for the Åushing process
or removed.
If the indoor coil is removed, the suction and liquid line
must be connected together on the indoor coil end. See
illustration for recommended method for connecting these
together.
If the indoor coil is left in place during Åushing, removing
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Refrigeration Installation
7.
8.
9.
10.
11.
12.
13.
14.
the existing refrigerant Åow control oriÄce or thermal
expansion valve prior to Åushing is highly recommended
to assure proper Åushing. Use a Äeld-provided Ätting or
piece of copper tubing to reconnect the lines where the
thermal expansion valve was removed.
Remove the pressure tap valve cores from the outdoor
unit’s service valves.
Connect an R-22 cylinder of clean R-22 refrigerant to the
vapor service valve. (see “Required Equipment Section”
for minimum required amount of R-22 for adequate
Åushing)
Connect the low pressure side of an R-22 gauge set to the
liquid line valve.
Connect a hose from the recovery machine with an empty
recovery drum to the common port of the gauge set.
Set the recovery machine for liquid recovery and start the
machine.
Open the gauge set low side valve. This will allow the
recovery machine to pull a vacuum on the existing system
line set.
Make sure to invert the cylinder of clean R-22 refrigerant
and open the cylinder’s valve to allow liquid refrigerant to
Åow into the system through the vapor line valve. (This
should allow the refrigerant to Åow from the cylinder and
through the line set before it enters the recovery machine.)
The cylinder should not be inverted if it is the type with
separate liquid and vapor valves. Use the liquid valve on
the cylinder in this case, keeping the cylinder upright.
Once the liquid refrigerant has been completely recovered,
switch the recovery machine to vapor recovery so that the
R-22 vapor can be completely recovered.
IMPORTANT! Always remember, every time the
system is Åushed you must always pull a vacuum
with a recovery machine on the system at the
end of each procedure. (If desired, a second Åushing
with clean refrigerant may be performed if insufÄcient
amounts of mineral oil were removed during the initial
Åush.)
15. Tightly close the valve on the inverted R-22 cylinder and
the gauge set valves.
16. Completely pump all remaining R22 refrigerant out of the
recovery machine and turn the machine off.
17. Before removing the recovery machine, R-22 refrigerant
cylinder and gauges, break the vacuum on the refrigerant
lines and indoor coil using dry-nitrogen.
18. Unsweat the liquid and vapor lines from the old indoor
coil or from each other and install a new matched Puron®
indoor coil, connecting the Åushed refrigerant lines to the
new coil using Äeld supplied connectors and tubing.
19. Reinstall pressure tap valve cores into unit service valves.
20. Pressurize the lines and coil and check for leaks in the line
set connection points using a soap solution.
21. Thoroughly evacuate the line set and indoor coil per the
instructions found in this manual.
22. Open the liquid and vapor service valves, releasing the
Puron® refrigerant contained in the outdoor unit into the
evacuated line set and indoor coil.
23. Energize the system and adjust the refrigerant charge
according to the charging procedures found in this
manual.
21
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Refrigeration Installation
FP2 Sensor Installation
An FP2 sensor with violet wiring is shipped loose with the
compressor section. This is the air coil low temperature
protection sensor. Install this sensor on the refrigerant line
between the indoor expansion valve and the air coil using
thermal compound and the supplied mounting clips. Ensure
that the sensor makes good thermal contact with the refrigerant
line and insulate the sensor.
Air coil low temperature protection will not be active if this
sensor is installed incorrectly or is not installed.
Add-On Heat Pump Applications
The indoor coil should be located in the supply side of
the furnace to avoid condensation damage to the furnace
heat exchanger for add-on heat pump applications. A high
temperature limit switch should be installed as shown in
Figure 11b just upstream of the coil to de-energize the
compressor any time the furnace is energized to avoid
blowing hot air directly into the coil, elevating refrigerant
pressures during operation. The heat pump will trip out on
high pressure lockout without some method of disengaging
the compressor during furnace operation. Alternatively, some
thermostats with “dual fuel” mode will automatically deenergize the compressor when second stage (backup) heat
is required.
The TXV should be brazed into place as shown in Figure 10,
keeping the “IN” side toward the compressor section. The
TXV has an internal check valve and must be installed in the
proper direction for operation. Always keep the valve body
cool with a brazing shield and wet rags to prevent damage
to the TXV. Attach the bulb to the suction line using the
supplied hose clamp. Be careful not to overtighten the clamp
and deform the bulb.
NOTICE! The air coil should be thoroughly washed with a
Älming agent, (dishwasher detergent like Cascade) to help
condensate drainage. Apply a 20 to 1 solution of detergent
and water. Spray both sides of coil, repeat and rinse
thoroughly with water.
Evacuation and Charging the Unit
LEAK TESTING - The refrigeration line set must be pressurized
and checked for leaks before evacuating and charging the unit.
To pressurize the line set, attach refrigerant gauges to the service
ports and add an inert gas (nitrogen or dry carbon dioxide) until
pressure reaches 60-90 psig [413-620 kPa]. Never use oxygen or
acetylene to pressure test. Use a halogen leak tester or a good
quality bubble solution to detect leaks on all connections made
in the Äeld. Check the service valve ports and stem for leaks. If
a leak is found, repair it and repeat the above steps. For safety
reasons do not pressurize system above 150 psig [1034 kPa].
System is now ready for evacuation and charging.
Turn service valves full out CCW (see Table 6) and then turn
back in one-half turn to open service ports. Add the required
refrigerant so that the total charge calculated for the unit
22
and line set is now in the system. Open the service valve
fully counter clockwise so that the stem will backseat and
prevent leakage through the schrader port while it is not in
use. Start unit in the heating mode and measure superheat
and subcooling values after 5 minutes of run time. See
tables 14d for superheat and sub-cooling values. Superheat
is measured using suction temperature and pressure at the
compressor suction line. Subcooling should be measured
using the liquid line temperature immediately outside the
compressor section cabinet and either the liquid line service
valve pressure or the compressor discharge pressure. Note
that different values from tables 14d will be obtained due to
the pressure losses through the condenser heat exchanger.
Adding refrigerant will increase sub-cooling while superheat
should remain fairly constant allowing for a slight amount
of hunting in TXV systems. This increase in subcooling will
require 5 minutes or so of operation before it should be
measured. After values are measured, compare to the chart
and go to “FINAL EVALUATION.”
PARTIAL CHARGE METHOD - Open service valve fully
counterclockwise and then turn back in one-half turn to
open service port. Add vaporized (Gas) into the suction side
of the compressor until the pressure in the system reaches
approximately 100-120 psig. Never add liquid refrigerant into
the suction side of a compressor. Start the unit in heating
and add gas to the suction port at a rate not to exceed
Äve pounds [2.27 kg] per minute. Keep adding refrigerant
until the complete charge has been entered. Superheat is
measured using suction temperature and pressure at the
compressor suction line. Subcooling should be measured
using the liquid line temperature immediately outside the
compressor section cabinet and either the liquid line service
valve pressure or the compressor discharge pressure. Note
that different values from tables 14d will be obtained due to
the pressure losses through the condenser heat exchanger.
Adding refrigerant will increase sub-cooling while superheat
should remain fairly constant allowing for a slight amount
of hunting in TXV systems. This increase in subcooling will
require 5 minutes or so of operation before it should be
measured. After values are measured, compare to the chart
and go to “FINAL EVALUATION.”
FINAL EVALUATION -In a split system, cooling subcooling
values can be misleading depending on the location of the
measurement. Therefore, it is recommended that charging
be monitored in the heating mode. Charge should be
evaluated by monitoring the subcooling in the heating mode.
After initial check of heating sub-cooling, shut off unit and
allow to sit 3-5 minutes until pressures equalize. Restart unit
in the cooling mode and check the cooling superheat against
Tables 14d. If unit runs satisfactorily, charging is complete. If
unit does not perform to speciÄcations the cooling TXV (air
coil side) may need to be readjusted (if possible) until the
cooling superheat values are met.
Checking Superheat and Subcooling
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Refrigeration Installation
Determining Superheat:
1. Measure the temperature of the suction line at a point
near the expansion valve bulb.
2. Determine the suction pressure by attaching refrigeration
gauges to the suction schrader connection at the
compressor.
3. Convert the pressure obtained in step 2 to saturation
temperature (boiling point) by using the pressure/
temperature conversion table on the gauge set.
4. Subtract the temperature obtained in step 3 from step
1. The difference will be the superheat of the unit or the
total number of degrees above saturation temperature.
Refer to Tables 14d for superheat ranges at speciÄc
entering water conditions.
Example:
The temperature of the suction line at the sensing bulb is
50°F. The suction pressure at the compressor is 110 psig
which is equivalent to 36°F saturation temperature from the
HFC-410A press/temp conversion table on the gauge set.
36°F subtracted from 50°F = 14°F Superheat.
Determining Sub-Cooling:
1. Measure the temperature of the liquid line on the smaller
refrigerant line (liquid line) just outside of the cabinet.
This location will be adequate for measurement in both
modes unless a signiÄcant temperature drop in the liquid
line is anticipated.
2. Determine the condensor pressure (high side) by
attaching refrigerant gauges to the schrader connection
on the liquid line service valve. If the hot gas discharge
line of the compressor is used, refer to the appropriate
column in Tables 14d.
3. Convert the pressure obtained in step 2 to the
saturation temperature by using the press/temp
conversion table on the gauge set.
4. Subtract the temperature of Step 3 from the temperature of
Step 1. The difference will be the sub-cooling value for that
unit (total degrees below the saturation temperature). Refer
to Tables 14a to 14d for sub-cooling values at speciÄc
entering water temperatures.
Example:
The condenser pressure at the service port is 335 psig,
which is equivalent to 104°F saturation temperature.
Discharge pressure is 365 psig at the compressor (109°F
saturation temperature). Measured liquid line temperature is
100°F. 100°F subtracted from 104°F = 4 degrees sub-cooling
(9 degrees if using the compressor discharge pressure).
23
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Refrigeration Installation
Figure 11a: Typical Split/Air Handler Installation
Power
Disconnects
TXV 'IN' toward
Compressor
Section
Insulated
Linesets
PVC Condensate
with vented trap
Compressor Section
Low Voltage
Air pad or Extruded
polystryene
Figure 11b: Typical Split/Add-on Coil Fossil Fuel Furnace Installation
TXV
'IN' toward
;?=05[V^HYK
*VTWYLZZVY
Compressor
:LJ[PVU
Section
(PY;LTWLYH[\YL
3PTP[:^P[JO
7=**VUKLUZH[L
^P[O]LU[LK[YHW
*VTWYLZZVY:LJ[PVU
(PYWHKVY,_[Y\KLK
WVS`Z[`YLUL
24
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Refrigeration Installation
Evacuation Of The Lineset And Coil
The line set and coil must be evacuated to at least 500
microns to remove any moisture and noncondensables.
Evacuate the system through both service ports in the
shipping position (full CW in - see table 6) to prevent false
readings on the gauge because of pressure drop through
service ports. A vacuum gauge or thermistor capable of
accurately meausuring the vacuum depth is crucial in
determining if the system is ready for charging. If the system
meets the requirements in Figure 12, it is ready for charging.
Figure 12: Evacuation Graph
Charging The System
There are two methods of charging a refrigerant system. One
method is the total charge method, where the volume of the
system is determined and the refrigerant is measured and
added into the evacuated system. The other method is the
partial charge method where a small initial charge is added
to an evacuated system, and remaining refrigerant added
during operation.
Total Charge Method - See Table 5 for the compressor
section basic charge. For line sets with 3/8” liquid lines
add 0.6 ounces of refrigerant to the basic charge for every
installed foot of liquid line [0.6 grams per cm]. Add 1.2 oz.
per foot [1.1 grams per cm] if using l/2” line. Once the total
charge is determined, the factory pre-charge (Table 5) is
subtracted and the remainder is the amount needed to be
added to the system. This method should be used with the
AHRI matched air handler.
ѥNOTICE! ѥ
NOTICE: Use tables 16a to 16d for superheat/
subcooling values. These tables use discharge pressure
(converted to saturation temperature) and liquid line
temperature for subcooling calculations. If using liquid
line pressure, subtract 3°F from the table values.
25
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Hot Water Generator
The HWG (Hot Water Generator) or desuperheater option
provides considerable operating cost savings by utilizing
excess heat energy from the heat pump to help satisfy
domestic hot water requirements. The HWG is active
throughout the year, providing virtually free hot water when
the heat pump operates in the cooling mode or hot water at
the COP of the heat pump during operation in the heating
mode. Actual HWG water heating capacities are provided in
the appropriate heat pump performance data.
Heat pumps equipped with the HWG option include a builtin water to refrigerant heat exchanger that eliminates the
need to tie into the heat pump refrigerant circuit in the Äeld.
The control circuit and pump are also built in for residential
equipment. Figure 13 shows a typical example of HWG water
piping connections on a unit with built-in circulating pump.
This piping layout reduces scaling potential.
The temperature set point of the HWG is Äeld selectable
to 125°F or 150°F . The 150°F set point allows more heat
storage from the HWG. For example, consider the amount
of heat that can be generated by the HWG when using the
125°F set point, versus the amount of heat that can be
generated by the HWG when using the 150°F set point.
In a typical 50 gallon two-element electric water heater
the lower element should be turned down to 100°F, or the
lowest setting, to get the most from the HWG. The tank will
eventually stratify so that the lower 80% of the tank, or 40
gallons, becomes 100°F (controlled by the lower element).
The upper 20% of the tank, or 10 gallons, will be maintained
at 125°F (controlled by the upper element).
Using a 125°F set point, the HWG can heat the lower 40
gallons of water from 100°F to 125°F, providing up to 8,330
btu’s of heat. Using the 150°F set point, the HWG can heat
the same 40 gallons of water from 100°F to 150°F and the
remaining 10 gallons of water from 125°F to 150°F, providing
This example ignored standby losses of the tank. When
those losses are considered the additional savings are even
greater.
Electric water heaters are recommended. If a gas, propane,
or oil water heater is used, a second preheat tank must be
installed (Figure 14). If the electric water heater has only a
single center element, the dual tank system is recommended
to insure a usable entering water temperature for the HWG.
Typically a single tank of at least 52 gallons (235 liters) is
used to limit installation costs and space. However, a dual
tank, as shown in Figure 14, is the most efÄcient system,
providing the maximum storage and temperate source water
to the HWG.
It is always advisable to use water softening equipment on
domestic water systems to reduce the scaling potential and
lengthen equipment life. In extreme water conditions, it may
be necessary to avoid the use of the HWG option since the
potential cost of frequent maintenance may offset or exceed
any savings. Consult Table 4 for scaling potential tests.
ѥWARNING! ѥ
WARNING! A 150°F SETPOINT MAY LEAD TO
SCALDING OR BURNS. THE 150°F SET POINT MUST
ONLY BE USED ON SYSTEMS THAT EMPLOY AN
APPROVED ANTI-SCALD VALVE.
Figure 14: HWG Double Tank Installation
(Indoor Compressor Section)
Hot Outlet to
house
Figure 13: Typical HWG Installation
(Indoor Compressor Section)
Cold Inlet
Hot Outlet
+RW2XWOHW
WRKRPH
Shut-off
Valve #1
Shut-off
Valve #1
8SSHU
HOHPHQWWR
120 - 130°F
[49 - 54°C]
3RZHUHG
:DWHU
+HDWHU
Cold Inlet from
Domestic supply
Cold Inlet from
Domestic supply
Shut-off
Valve #4
Shut-off
Valve #3
a total of up to 18,743 btu’s of heat, or more than twice as
much heat as when using the 125°F set point.
/RZHU
HOHPHQWWR
100 - 110°F
[38 - 43°C]
Upper element to 130°F [54°C]
(or owner preference)
Shut-off
Valve #4
Powered
Shut-off
Valve #3
Water Heater
Lower element to 120°F [49°C]
Unpowered
Water Heater
Shut Off
Valve #2
Field Supplied 3/4” brass nipple and “T”
Shut Off
Valve #2
Insulated water lines - 5/8” OD, 50 ft maximum (one way)
[16mm OD, 15 meters maximum]
,QVXODWHGZDWHUOLQHV
µ2'IWPD[LPXPRQHZD\PHWHUV
>PP2'PHWHUVPD[LPXP@
26
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Hot Water Generator
Installation
The HWG is controlled by two sensors and a microprocessor
control. One sensor is located on the compressor discharge
line to sense the discharge refrigerant temperature. The
other sensor is located on the HWG heat exchanger’s “Water
In” line to sense the potable water temperature.
Figure 15:
ANTI-SCALD
VALVE PIPING
CONNECTIONS
ANTI-SCALD
VALVE
ѥWARNING! ѥ
The microprocessor control monitors the refrigerant and
water temperatures to determine when to operate the HWG.
The HWG will operate any time the refrigerant temperature
is sufÄciently above the water temperature. Once the
HWG has satisÄed the water heating demand during a
heat pump run cycle, the controller will cycle the pump at
regular Intervals to determine if an additional HWG cycle
can be utilized. The microprocessor control Includes 3 DIP
switches, SW10 (HWG PUMP TEST), SW11 (HWG TEMP),
and SW12 (HWG STATUS).
SW10 HWG PUMP TEST. When this switch is in the “ON”
position, the HWG pump is forced to operate even if there
is no call for the HWG. This mode may be beneÄcial to
assist in purging the system of air during Initial start up.
When SW10 is in the “OFF” position, the HWG will operate
normally. This switch is shipped from the factory in the
“OFF” (normal) position. NOTE; If left in the “On” position for
5 minutes, the pump control will revert to normal operation.
SW11 HWG TEMP. The control setpoint of the HWG can
be set to either of two temperatures, 125°F or 150°F. When
SW11 is in the “ON” position the HWG setpoint is 150°F.
When SW11 is in the “OFF” position the HWG setpoint is
ѥWARNING! ѥ
WARNING! USING A 150°F SETPOINT ON THE
HWG WILL RESULT IN WATER TEMPERATURES
SUFFICIENT TO CAUSE SEVERE PHYSICAL INJURY
IN THE FORM OF SCALDING OR BURNS, EVEN
WHEN THE HOT WATER TANK TEMPERATURE
SETTING IS VISIBLY SET BELOW 150°F. THE 150°F
HWG SETPOINT MUST ONLY BE USED ON SYSTEMS
THAT EMPLOY AN APPROVED ANTI-SCALD VALVE
(PART NUMBER AVAS4) AT THE HOT WATER
STORAGE TANK WITH SUCH VALVE PROPERLY
SET TO CONTROL WATER TEMPERATURES
DISTRIBUTED TO ALL HOT WATER OUTLETS AT A
TEMPERATURE LEVEL THAT PREVENTS SCALDING
OR BURNS!
HOT WATER
TO HOUSE
C
M
H
8” MAX
WARNING! UNDER NO CIRCUMSTANCES SHOULD
THE SENSORS BE DISCONNECTED OR REMOVED
AS FULL LOAD CONDITIONS CAN DRIVE HOT
WATER TANK TEMPERATURES FAR ABOVE SAFE
TEMPERATURE LEVELS IF SENSORS HAVE BEEN
DISCONNECTED OR REMOVED.
CHECK VALVE
COLD WATER
SUPPLY
WATER HEATER
125°F. This switch Is shipped from the factory in the “OFF”
(125°F) position.
SW12 HWG STATUS. This switch controls operation of
the HWG. When SW12 is in the “ON” position the HWG is
disabled and will not operate. When SW12 is in the “OFF”
position the HWG is in the enabled mode and will operate
normally. This switch is shipped from the factory in the
“ON” (disabled) position. CAUTION: DO NOT PLACE THIS
SWITCH IN THE ENABLED POSITION UNITL THE HWG
PIPING IS CONNECTED, FILLED WITH WATER, AND
PURGED OR PUMP DAMAGE WILL OCCUR.
When the control is powered and the HWG pump output
is not active, the status LED (AN1) will be “On”. When the
HWG pump output is active for water temperature sampling
or HWG operation, the status LED will slowly Åash (On 1
second, Off 1 second).
If the control has detected a fault, the status LED will Åash a
numeric fault code as follows:
Hot Water Sensor Fault
Compressor Discharge sensor fault
High Water Temperature (>160ºF)
Control Logic Error
1 Åash
2 Åashes
3 Åashes
4 Åashes
Fault code Åashes have a duration of 0.4 seconds with
a 3 second pause between fault codes. For example, a
“Compressor Discharge sensor fault” will be four Åashes
0.4 seconds long, then a 3 second pause, then four Åashes
again, etc.
27
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Hot Water Generator
For Indoor Compressor Section Only
Warning! The HWG pump Is fully wired from the
factory. Use extreme caution when working around
the microprocessor control as it contains line voltage
connections that presents a shock hazard that can
cause severe injury or death!
The heat pump, water piping, pump, and hot water tank
should be located where the ambient temperature does
not fall below 50°F [10°C]. Keep water piping lengths at a
minimum. DO NOT use a one way length greater than 50 ft.
(one way) [15 m]. See Table 7 for recommended piping sizes
and maximum lengths.
All installations must be in accordance with local codes. The
installer is responsible for knowing the local requirements,
and for performing the installation accordingly. DO NOT
energize the pump until “water tank reÄll” section, below is
completed. Powering the pump before all installation steps
are completed may damage the pump.
Water Tank Preparation
1. Turn off power or fuel supply to the hot water tank.
2. Connect a hose to the drain valve on the water tank.
3. Shut off the cold water supply to the water tank.
4. Open the drain valve and open the pressure relief valve
or a hot water faucet to drain tank.
5. When using an existing tank, it should be Åushed with
cold water after it is drained until the water leaving the
drain hose is clear and free of sediment.
6. Close all valves and remove the drain hose.
7. Install HWG water piping.
HWG Water Piping
1. Using at least 5/8” [16mm] O.D. copper, route and install
the water piping and valves as shown in Figures 13 or
14. Install an approved anti-scald valve if the 150°F HWG
setpoint is or will be selected. An appropriate method
must be employed to purge air from the HWG piping.
This may be accomplished by Åushing water through the
HWG (as In Figures 13 and 14) or by Installing an air vent
at the high point of the HWG piping system.
2. Insulate all HWG water piping with no less than 3/8”
[10mm] wall closed cell insulation.
3. Open both shut off valves and make sure the tank drain
valve is closed.
Water Tank ReÀll
1. Close valve #4. Ensure that the HWG valves (valves #2
and #3) are open. Open the cold water supply (valve #1)
to Äll the tank through the HWG piping. This will purge air
from the HWG piping.
2. Open a hot water faucet to vent air from the system until
water Åows from faucet; turn off faucet. Open valve #4.
3. Depress the hot water tank pressure relief valve handle to
ensure that there is no air remaining in the tank.
4. Inspect all work for leaks.
5. Before restoring power or fuel supply to the water heater,
adjust the temperature setting on the tank thermostat(s)
to insure maximum utilization of the heat available from
28
the refrigeration system and conserve the most energy.
On tanks with both upper and lower elements and
thermostats, the lower element should be turned down
to 100°F [38°C] or the lowest setting; the upper element
should be adjusted to 120-130°F [49-54°C]. Depending
upon the speciÄc needs of the customer, you may want
to adjust the upper element differently. On tanks with a
single thermostat, a preheat tank should be used (Fig 14).
6. Replace access cover(s) and restore power or
fuel supply.
Initial Start-Up
1. Make sure all valves in the HWG water circuit are
fully open.
2. Turn on the heat pump and allow it to run for
10-15 minutes.
3. Set SW12 to the “OFF” position (enabled) to engage the
HWG.
4. The HWG pump should not run if the compressor is not
running.
5. The temperature difference between the water entering
and leaving the HWG coil should be approximately
5-10°F [3-6°C].
6. Allow the unit to operate for 20 to 30 minutes to insure
that it is functioning properly.
Table 7: HWG Water Piping Size and Length
Unit
Nominal
Tonnage
Nominal
HWG Flow
(gpm)
1/2" Copper
(max length*)
3/4" Copper
(max length*)
1.5
0.6
50
-
2.0
0.8
50
-
2.5
1.0
50
-
3.0
1.2
50
-
3.5
1.4
50
-
4.0
1.6
45
50
5.0
2.0
25
50
6.0
2.4
10
50
*Maximum length is equivalent length (in feet) one way of type L
copper.
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Hot Water Generator Module Refrigeration Installation
For Outdoor Compressor Section Only
General Information
The HWG Module consists of an all-copper, vented doublewall heat exchanger and a water-cooled water circulating
pump. The pump is controlled by a microprocessor in the
HWG module. Power for the pump is provided from a remote
115 vac power source.
Location/Mounting
The HWG module should be mounted as close to the heat
pump outdoor section as possible, in order to minimize
the length of refrigerant run. Indoor mounting is preferred,
where practical, to reduce the likelihood of freezing ambient
temperature. It is recommended that the HWG module be
mounted above the system compressor in order to promote
proper oil movement and drain-down. This means that the
HWG module can be wall mounted in any orientation
except for stubs up. Mounting should be accomplished
by fastening the HWG module cabinet to the wall or other
selected vertical surface. Mounting holes are provided at
the rear of the unit. Any fastener suitable for supporting a 12
pound [5.4] vertical load is acceptable.
The HWG, water piping and hot water tank should be
located where the ambient temperature does not fall below
50°F [10°C]. Keep water piping lengths at a minimum. DO
NOT use a one-way length greater than 50 ft. (one way) [15
m]. See Table 7 for maximum water piping lengths.
All installations must be in accordance with local codes. The
installer is responsible for knowing the local requirements,
and for performing the installation accordingly
SPECIAL NOTE: The selected mounting location and
orientation must allow the circulator pump to be positioned
with the motor shaft horizontal. DO NOT install the Heat
Recovery Unit Åat on its back.
Refrigerant Line Installation
Before starting the installation into the refrigerant circuit,
inspect and note the condition and performance of the heat
pump. Disconnect power to the heat pump outdoor unit. Any
system deÄciencies must be corrected prior to installing the
HWG module. Addition of the unit will not correct system
problems. Record the suction and discharge pressures and
compressor amperage draw. These will be used for comparison with system operation after the refrigerant line installation is complete and before the water line installation is
performed.
Install the Add-On HWG Kit
Locate the HWG as close to the water heater as possible.
Install the lineset to the desuperheater valves in the outdoor
compressor section and the refrigerant line connections
on the HWG. Maximum length should be 30 feet one way.
Evacuate the lineset to 500 microns through the hot gas
valves in the outdoor unit. Open the HWG valves in the compressor section up fully (and close the desuperheater bypass
valve). See Figures 16a through 16d. Check the lineset for
leaks. Verify that lineset tubing is completely insulated with a
minimum 1/2” thick closed cell and painted to prevent deterioration of the insulation due to ultra violet light and weather.
Make the connections with high temperature solder or brazing rod. The recommended refrigerant line size is dependent
on the one way distance between the Heat Recovery Unit
and the compressor; and the size of the system. Use Table 8
as a guideline.
Initial Start-Up
1. Make sure all valves in the HWG water circuit are fully
open.
2. Turn the heat pump power and remote HWG power “off”
and switch dip switch SW12 on the HWG controller to the
“off” (enabled) position to activate the HWG.
3. The HWG pump should not run if the compressor is not
running.
4. The temperature difference between the water entering
and leaving the HWG should be approximately 5-10 °F
[3-6 °C].
5. Allow the unit to operate for 20 to 30 minutes insure that
it is functioning properly.
6. Always turn dip switch SW12 on the HWG controller to
the “on” (disabled) position to deactivate the HWG when
servicing the outdoor compressor section.
NOTICE! Make sure the compressor discharge line
is connected to the “Hot Gas In” stub on the Heat
Recovery Unit.
ѥWARNING! ѥ
WARNING! The HWG module is an appliance that operates
in conjunction with the heat pump system, the hot water
system and the electrical system. Installation should only be
performed by skilled technicians with appropriate training
and experience. The installation must be in compliance with
local codes and ordinances. Local plumbing and electrical
building codes take precedence over instructions contained
herein. The Manufacturer accepts no liability for equipment
damaged and/or personal injury arising from improper
installation of the HWG module.
ѥCAUTION! ѥ
CAUTION! The HWG module must be installed in an area
that is not subject to freezing temperatures.
ѥCAUTION! ѥ
CAUTION! Locate Refrigerant lines to avoid accidental
damage by lawnmowers or children.
29
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Hot Water Generator Module Refrigeration Installation
Outdoor Compressor Section Only
Figure 16a: Outdoor Compressor Section HWG Installation
Table 8: HWG Refrigerant Line Sizing
Capacity
Refr to
HWG
Line Set Size
1/2” OD
5/8” OD
3/4” OD
2 Ton
Up to 16 ft.
[4.9m]
Up to 30 ft.
[9.1m]
N/A
3 Ton
Up to 9 ft.
[2.7m]
Up to 25 ft.
[7.6m]
Up to 30 ft.
[9.1m]
4 Ton
Up to 5 ft.
[1.5m]
Up to 13 ft.
[4.0m]
Up to 30 ft.
[9.1m]
5 Ton
N/A
Up to 9 ft.
[2.7m]
Up to 25 ft.
[7.6m]
Refr from
HWG
Figure 16c: HWG Service Valves
Fully Insulated
Lines to the HWG
Figure 16b: Remote HWG Module
Control
Board
HWG
Refr Out
HWG
Water Out
HWG
Refr In
Circulator
High Voltage
HWG
Water In
Figure 16d: HWG Bypass Valve
Valve Open
(HWG Bypassed)
Figure 17: HWG Wiring
E
E
E
30
Valve Closed
(HWG Activated)
Refr
to HWG
Refr from
HWG
HWG
Bypass
Valve
HWG
Line Valves
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Electrical - Line Voltage
All final electrical connections must be made with a length of
flexible conduit to minimize vibration and sound transmission
to the building.
ѥWARNING! ѥ
WARNING! To avoid possible injury or death due to
electrical shock, open the power supply disconnect switch
and secure it in an open position during installation.
General Line Voltage Wiring
Be sure the available power is the same voltage and phase
shown on the unit serial plate. Line and low voltage wiring
must be done in accordance with local codes or the National
Electric Code, whichever is applicable.
ѥCAUTION! ѥ
CAUTION! Use only copper conductors for field installed
electrical wiring. Unit terminals are not designed to accept
other types of conductors.
Power Connection
Line voltage connection is made by connecting the incoming
line voltage wires to the “L” side of the contactor as shown
in Figures 18 and 19. Consult Table 9a or 9b for correct fuse
size.
Electrical - Line Voltage
All field installed wiring, including electrical ground, must
comply with the National Electrical Code as well as all
applicable local codes. Refer to the unit electrical data for fuse
sizes. Consult wiring diagram for field connections that must
be made by the installing (or electrical) contractor.
208-230 Volt Operation
Verify transformer tap with air handler wiring diagram to
insure that the transformer tap is set to the correct voltage,
208V or 230V.
Table 7a: GT-PX Series Electrical Data
Compressor
RLA
LRA
Qty
HWG
Pump FLA
026
10.3
52.0
1
0.4
4.0
14.7
17.3
25
038
16.7
82.0
1
0.4
4.0
21.1
25.3
40
049
21.2
96.0
1
0.4
4.0
25.6
30.9
50
064
25.6
118.0
1
0.4
4.0
30.0
36.4
60
Model
Rated Voltage of 208/230/60/1
HACR circuit breaker in USA only
External
Pump FLA
Total Unit
FLA
Min Circuit
Amps
Max Fuse/
HACR (2)
Min/Max Voltage of 197/254
All fuses Class RK-5
Table 7b: GT-PE Series Electrical Data
Compressor
RLA
LRA
Qty
Internal Loop
Pump FLA
026
10.3
52.0
1
0.8
11.1
13.7
20
036
16.7
82.0
1
0.8
17.5
21.7
35
048
21.2
96.0
1
1.6
22.8
28.1
45
062
25.6
118.0
1
1.6
27.2
33.6
50
Model
Total
Unit FLA
Min Circuit
Amps
Max Fuse/
HACR
Rated Voltage of 208/230/60/1
HACR circuit breaker in USA only
Min/Max Voltage of 197/254
All fuses Class RK-5
HWG Module
Voltage
Pump
FLA
Total
FLA
Min Circuit
Amps
AHWG1AARS
115/60/1
0.52
0.52
1.20
AHWG1AGRS
208/230/60/1
0.40
0.40
0.90
31
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Electrical - Power Wiring
Figure 18: Indoor Compressor Section Line Voltage Field Wiring
Unit Power Supply
(see electrical table for wire
and breaker size)
Figure 19: Outdoor Compressor Section Line Voltage Field Wiring
Consult Electrical Table for wire and fuse size.
All power wiring per local code
L2
T2
T1
L1
ELECTRICAL - HWG WIRING
208-230 Volt Operation
Verify transformer tap with air handler wiring diagram to
insure that the transformer tap is set to the correct voltage,
208V or 230V.
HWG Module Wiring - For “Outdoor” Compressor
Section
The HWG module should be wired to a 115 vac power
supply as shown in ¿gure 20. A safety disconnect should be
installed at the HWG module as required by code to allow
servicing of the module. DO NOT energize the pump until all
HWG piping is completed and air is purged from the water
piping to avoid running the pump “dry”.
Figure 20: HWG Module Wiring - For Use with Outdoor Compressor Section
HWG Module
CONDENSER
CONDENSER
CONDENSER
32
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Electrical - Low Voltage Wiring
Thermostat Connections (Indoor Compresor Section)
The thermostat should be wired directly to the CXM board.
Figure 21 show low voltage wiring. Note that the air handler
or furnace transformer will be used to power the CXM board
in the compressor section. See “Electrical – Thermostat” for
speci¿c terminal connections.
Low Air Temperature Sensor Installation
After mounting the FP2 sensor in the air handler connect the
sensor wiring to the violet wires in the compressor section’s
control box as shown in Figure 22. Clip the violet wire
loop in the compressor section’s control box. Wire the
violet leads from FP2 to the violet leads clipped in the control
box. FP2 sensor is packed inside the compressor section
control box.
Figure 21: GT-PX Low Voltage Field Wiring
Low Water Temperature Cutout Selection
The CXM control allows the ¿eld selection of low water (or
water-antifreeze solution) temperature limit by clipping jumper
JW3, which changes the sensing temperature associated with
thermistor FP1. Note that the FP1 thermistor is located on
the refrigerant line between the coaxial heat exchanger and
expansion device (TXV). Therefore, FP1 is sensing refrigerant
temperature, not water temperature, which is a better indication
of how water Àow rate/temperature is affecting the refrigeration
circuit.
Low voltage
Äeld wiring
Thermostat Connections (Outdoor Compressor Section)
The thermostat should be wired through the air handler to
the outdoor compressor section. Typical thermostat wiring
is shown in Figure 22. Note that the air handler or furnace
transformer will be used to power the CXM board in the
compressor section.
The factory setting for FP1 is for systems using water (30°F
[-1.1°C] refrigerant temperature). In low water temperature
(extended range) applications with antifreeze (most ground
loops), jumper JW3 should be clipped as shown in Figure
23 to change the setting to 10°F [-12.2°C] refrigerant
temperature, a more suitable temperature when using
an antifreeze solution. All residential units include water/
refrigerant circuit insulation to prevent internal condensation,
which is required when operating with entering water
temperatures below 59°F [15°C].
33
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Electrical - Low Voltage Wiring
34
T1
L1
L2
T2
Low Voltage
Connector
Figure 22: GT-PE Low Voltage Field Wiring
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Electrical - Low Voltage Wiring
Note: This valve can overheat the anticipator of an
electromechanical thermostat. Therefore, only relay or triac
based thermostats should be used.
Figure 23: FP1 Limit Setting
CXM PCB
JW3-FP1 jumper
should be clipped
for low temperature
operation
Accessory Connections
A terminal paralleling the compressor contactor coil has been
provided on the CXM control. Terminal “A” is designed to
control accessory devices, such as water valves. Note: This
terminal should be used only with 24 Volt signals and not
line voltage. Terminal “A” is energized with the compressor
contactor. See Figure 24 or the speci¿c unit wiring diagram
for details.
Figure 24: Accessory Wiring
Two-stage Units
Two-stage units should be designed with two parallel valves
for ground water applications to limit water use during Ärst
stage operation. For example, at 1.5 gpm/ton [2.0 l/m per
kW], a model 049 unit requires 6 gpm [23 l/m] for full load
(2nd stage) operation, but only 4 gpm [15 l/m] during 1st
stage operation. Since the unit will operate on Ärst stage 8090% of the time, signiÄcant water savings can be realized by
using two parallel solenoid valves with two Åow regulators.
In the example above, stage one solenoid would be installed
with a 4 gpm [15 l/m] Åow regulator on the outlet, while stage
two would utilize a 2 gpm [8 l/m] Åow regulator. When stage
one is operating, the second solenoid valve will be closed.
When stage two is operating, both valves will be open,
allowing full load Åow rate.
Figure 27 illustrates piping for two-stage solenoid valves.
Review Ägures 24-26 for wiring of stage one valve. Stage
two valve should be wired between “Y2” (compressor
solenoid -- wire nut connection) and terminal “C.” NOTE:
When EWT is below 50°F [10°C], a minimum of 2 gpm per
ton (2.6 l/m per kW) is required.
C
Y1
Figure 25: AMV Valve Wiring
2
3
1
AVM
Taco Valve
Y1
Water Solenoid Valves - “Indoor” Compressor
Section Only
An external solenoid valve(s) should be used on ground
water installations to shut off Åow to the unit when the
compressor is not operating. A slow closing valve may be
required to help reduce water hammer. Figure 24 shows
typical wiring for a 24VAC external solenoid valve. Figures
25 and 26 illustrate typical slow closing water control valve
wiring for Taco 500 series (P/N AVM…) and Taco SBV series
valves. Slow closing valves take approximately 60 seconds
to open (very little water will Åow before 45 seconds). Once
fully open, an end switch allows the compressor to be
energized. Only relay or triac based electronic thermostats
should be used with slow closing valves. When wired as
shown, the slow closing valve will operate properly with the
following notations:
C
Heater Switch
Thermostat
Figure 26: Taco SBV Valve Wiring
1. The valve will remain open during a unit lockout.
2. The valve will draw approximately 25-35 VA through the
“Y” signal of the thermostat.
35
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Electrical - Low Vo
Voltage Wiring
WIRING
Figure 27: Two-Stage Piping
Solenoid
Valve
Figure 28a: Typical Thermostat Wiring, TAH AHU with
AHU32U03/4
Flow
Regulator
T-Stat
ATP32U03
ATP32U04
Fan Control
Board
Y2
Stage 2
To Discharge
OUT
TAH Air
Handler
Y2
Terminal
Blocks in
Compressor
Section
Y2
Stage 1
IN
From Water Source
NOTE: Shut-off valves, strainers and
other required components not shown.
ѥCAUTION! ѥ
CAUTION! Many units are installed with a factory or ¿eld
supplied manual or electric shut-off valve. DAMAGE WILL
OCCUR if shut-off valve is closed during unit operation. A
high pressure switch must be installed on the heat pump
side of any ¿eld provided shut-off valves and connected to
the heat pump controls in series with the built-in refrigerant
circuit high pressure switch to disable compressor
operation if water pressure exceeds pressure switch
setting. The ¿eld installed high pressure switch shall have
a cut-out pressure of 300 psig and a cut-in pressure of
250 psig. This pressure switch can be ordered with a 1/4”
internal Àare connection as part number 39B0005N02.
ELECTRICAL - THERMOSTAT WIRING
Thermostat Installation
The thermostat should be located on an interior wall in a
larger room, away from supply duct drafts. DO NOT locate
the thermostat in areas subject to sunlight, drafts or on
external walls. The wire access hole behind the thermostat
may in certain cases need to be sealed to prevent erroneous
temperature measurement. Position the thermostat back
plate against the wall so that it appears level and so the
thermostat wires protrude through the middle of the back
plate. Mark the position of the back plate mounting holes and
drill holes with a 3/16” (5mm) bit. Install supplied anchors and
secure plate to the wall. Thermostat wire must be 18 AWG
wire. Wire the appropriate thermostat as shown in Figures
28a through 28c to the low voltage terminal strip on the CXM
control board. Practically any heat pump thermostat will
work with these units, provided it has the correct number of
heating and cooling stages.
ѥCAUTION! ѥ
CAUTION! Refrigerant pressure activated water regulating
valves should never be used with the equipment.
36
Y1
Y1
Y1
O
O
O
G
G
G
R
R
R
C
C
C
W
W
W
L
A
A
C01
C01
FP
FP
FP
FP
+V
+V
W1
W1
W2
W2
IMPORTANT: Violet jumper from FP to FP on Terminal
block 2 in compressor section must be removed when
unit is installed with TAH air handler or when FP2
sensor is Äeld installed on existing air handler.
See equipment wiring diagram for more details.
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Electrical - Low Voltage Wiring
Figure 28b: Typical Thermostat Wiring, Single-Stage
Units (2 Heat/1 Cool)
CXM Board
(Compressor
Section)
Typical
Air Handler
Typical
T-stat
Y
Y/Y2
Y
O
O
O
G
G
G
R
R
R
C
C
C
W1
W
Optional
Jumper
W2
E
AL1
L
Figure 28c: Typical Thermostat Wiring, Two-Stage Units
(3 Heat/2 Cool)
From Compressor
Solenoid Valve
CXM Board
(Compressor
Section)
Typical
Air Handler
Y/Y2
Typical
T-stat
Y2
Y
Y1
Y1
O
O
O
G
G
G
R
R
R
C
C
C
W1
W
W2
E
AL1
L
37
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
CXM Controls
CXM Control
For detailed control information, see CXM Application,
Operation and Maintenance (AOM) manual (part
#97B0003N12).
Field Selectable Inputs
Test mode: Test mode allows the service technician to
check the operation of the control in a timely manner. By
momentarily shorting the test terminals, the CXM control
enters a 20 minute test mode period in which all time delays
are sped up 15 times. Upon entering test mode, the status
LED will Åash a code representing the last fault. For diagnostic
ease at the thermostat, the alarm relay will also cycle during
test mode. The alarm relay will cycle on and off similar to the
status LED to indicate a code representing the last fault, at
the thermostat. Test mode can be exited by shorting the test
terminals for 3 seconds.
Retry Mode: If the control is attempting a retry of a fault,
the status LED will slow Åash (slow Åash = one Åash every 2
seconds) to indicate the control is in the process of retrying.
On = EH2 Normal. Off = DDC Output at EH2.
NOTE: Some CXM controls only have a 2 position DIP switch
package. If this is the case, this option can be selected by
clipping the jumper which is in position 4
of SW1.
Jumper not clipped = EH2 Normal. Jumper clipped = DDC
Output at EH2.
DIP switch 5: Factory Setting - Normal position is “On.” Do
not change selection unless instructed to do so by
the factory.
Table 10: CXM LED And Alarm
Relay Operations
Description of Operation
LED
Alarm Relay
Field ConÄguration Options
Note: In the following Äeld conÄguration options, jumper
wires should be clipped ONLY when power is removed from
the CXM control.
Normal Mode
Normal Mode with UPS Warning
CXM is non-functional
Fault Retry
Lockout
Over/Under Voltage Shutdown
On
On
Off
Slow Flash
Fast Flash
Slow Flash
Open
Cycle (closed 5 sec., Open 25 sec.)
Open
Open
Closed
Open (Closed after 15 minutes)
Water coil low temperature limit setting: Jumper 3 (JW3FP1 Low Temp) provides Äeld selection of temperature limit
setting for FP1 of 30°F or 10°F [-1°F or -12°C] (refrigerant
temperature).
Test Mode - No fault in memory
Flashing Code 1
Cycling Code 1
Test Mode - HP Fault in memory Flashing Code 2
Cycling Code 2
Test Mode - LP Fault in memory
Flashing Code 3
Cycling Code 3
Not Clipped = 30°F [-1°C]. Clipped = 10°F [-12°C].
Test Mode - FP1 Fault in memory Flashing Code 4
Cycling Code 4
Air coil low temperature limit setting: Jumper 2 (JW2-FP2
Low Temp) provides Äeld selection of temperature limit
setting for FP2 of 30°F or 10°F [-1°F or -12°C] (refrigerant
temperature). Note: This jumper should only be clipped
under extenuating circumstances, as recommended by
the factory.
Test Mode - FP2 Fault in memory Flashing Code 5
Cycling Code 5
Test Mode - CO Fault in memory Flashing Code 6
Cycling Code 6
Test Mode - Over/Under
shutdown in memory
Flashing Code 7
Cycling Code 7
Test Mode - UPS in memory
Flashing Code 8
Cycling Code 8
Test Mode - Swapped Thermistor Flashing Code 9
Cycling Code 9
Not Clipped = 30°F [-1°C]. Clipped = 10°F [-12°C].
Alarm relay setting: Jumper 1 (JW1-AL2 Dry) provides Äeld
selection of the alarm relay terminal AL2 to be jumpered to
24VAC or to be a dry contact (no connection).
Not Clipped = AL2 connected to R. Clipped = AL2 dry
contact (no connection).
DIP Switches
Note: In the following Äeld conÄguration options, DIP
switches should only be changed when power is removed
from the CXM control.
DIP switch 1: Unit Performance Sentinel Disable - provides
Äeld selection to disable the UPS feature.
On = Enabled. Off = Disabled.
DIP switch 2: Stage 2 Selection - provides selection of
whether compressor has an “on” delay. If set to stage 2, the
compressor will have a 3 second delay before energizing.
Also, if set for stage 2, the alarm relay will NOT cycle during
test mode.
On = Stage 1. Off = Stage 2
38
DIP switch 3: Not Used.
DIP switch 4: DDC Output at EH2 - provides selection for
DDC operation. If set to “DDC Output at EH2,” the EH2
terminal will continuously output the last fault code of
the controller. If set to “EH2 normal,” EH2 will operate as
standard electric heat output.
-Slow Flash = 1 Åash every 2 seconds
-Fast Flash = 2 Åashes every 1 second
-Flash code 2 = 2 quick Åashes, 10 second pause, 2 quick
Åashes, 10 second pause, etc.
-On pulse 1/3 second; off pulse 1/3 second
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
CXM Controls
Safety Features – CXM Control
The safety features below are provided to protect the
compressor, heat exchangers, wiring and other components
from damage caused by operation outside of design
conditions.
Anti-short cycle protection: The control features a 5 minute
anti-short cycle protection for the compressor.
Note: The 5 minute anti-short cycle also occurs at power up.
Random start: The control features a random start upon
power up of 5-80 seconds.
Fault Retry: In Fault Retry mode, the Status LED begins
slowly Åashing to signal that the control is trying to recover
from a fault input. The control will stage off the outputs and
then “try again” to satisfy the thermostat input call. Once the
thermostat input call is satisÄed, the control will continue on
as if no fault occurred. If 3 consecutive faults occur without
satisfying the thermostat input call, the control will go into
“lockout” mode. The last fault causing the lockout will be
stored in memory and can be viewed by going into test mode.
Note: FP1/FP2 faults are factory set at only one try.
Lockout: In lockout mode, the status LED will begin fast
Åashing. The compressor relay is turned off immediately.
Lockout mode can be “soft” reset by turning off the
thermostat (or satisfying the call). A “soft” reset keeps
the fault in memory but resets the control. A “hard” reset
(disconnecting power to the control) resets the control and
erases fault memory.
Lockout with emergency heat: While in lockout mode, if W
becomes active (CXM), emergency heat mode will occur.
High pressure switch: When the high pressure switch opens due
to high refrigerant pressures, the compressor relay is de-energized
immediately since the high pressure switch is in series with the
compressor contactor coil. The high pressure fault recognition is
immediate (does not delay for 30 continuous seconds before deenergizing the compressor).
High pressure lockout code = 2
Example: 2 quick Åashes, 10 sec pause, 2 quick Åashes, 10
sec. pause, etc.
Low pressure switch: The low pressure switch must be open
and remain open for 30 continuous seconds during “on” cycle
to be recognized as a low pressure fault. If the low pressure
switch is open for 30 seconds prior to compressor power up it
will be considered a low pressure (loss of charge) fault. The low
pressure switch input is bypassed for the initial 120 seconds of a
compressor run cycle.
lockout mode once the FP1 fault has occurred.
FP1 lockout code = 4
Air coil low temperature (FP2): The FP2 thermistor temperature
must be below the selected low temperature limit setting for
30 continuous seconds during a compressor run cycle to be
recognized as a FP2 fault. The FP2 input is bypassed for the
initial 120 seconds of a compressor run cycle. FP2 is set at the
factory for one try. Therefore, the control will go into lockout
mode once the FP2 fault has occurred.
FP2 lockout code = 5
Condensate overÅow: The condensate overÅow sensor
must sense overÅow level for 30 continuous seconds to
be recognized as a CO fault. Condensate overÅow will be
monitored at all times.
CO lockout code = 6
Over/under voltage shutdown: An over/under voltage
condition exists when the control voltage is outside the range
of 18VAC to 31.5VAC. Over/under voltage shut down is a
self-resetting safety. If the voltage comes back within range
for at least 0.5 seconds, normal operation is restored. This is
not considered a fault or lockout. If the CXM is in over/under
voltage shutdown for 15 minutes, the alarm relay will close.
Over/under voltage shut down code = 7
Unit Performance Sentinel-UPS (patent pending): The UPS
feature indicates when the heat pump is operating inefÄciently.
A UPS condition exists when:
a) In heating mode with compressor energized, FP2 is
greater than 125°F [52°C] for 30 continuous seconds, or:
b) In cooling mode with compressor energized, FP1 is
greater than 125°F [52°C] for 30 continuous seconds, or:
c) In cooling mode with compressor energized, FP2 is less
than 40°F [4.5°C] for 30 continuous seconds. If a UPS
condition occurs, the control will immediately go to UPS
warning. The status LED will remain on as if the control
is in normal mode. Outputs of the control, excluding LED
and alarm relay, will NOT be affected by UPS. The UPS
condition cannot occur during a compressor off cycle.
During UPS warning, the alarm relay will cycle on and
off. The cycle rate will be “on” for 5 seconds, “off” for 25
seconds, “on” for 5 seconds, “off” for 25 seconds, etc.
UPS warning code = 8
Swapped FP1/FP2 thermistors: During test mode, the control
monitors to see if the FP1 and FP2 thermistors are in the
appropriate places. If the control is in test mode, the control
will lockout, with code 9, after 30 seconds if:
a) The compressor is on in the cooling mode and the FP1
sensor is colder than the FP2 sensor, or:
b) The compressor is on in the heating mode and the FP2
sensor is colder than the FP1 sensor.
Low pressure lockout code = 3
Swapped FP1/FP2 thermistor code = 9.
Water coil low temperature (FP1): The FP1 thermistor
temperature must be below the selected low temperature limit
setting for 30 continuous seconds during a compressor run
cycle to be recognized as a FP1 fault. The FP1 input is bypassed
for the initial 120 seconds of a compressor run cycle. FP1 is
set at the factory for one try. Therefore, the control will go into
Diagnostic Features
The LED on the CXM board advises the technician of the
current status of the CXM control. The LED can display either
the current CXM mode or the last fault in memory if in test
mode. If there is no fault in memory, the LED will Åash Code 1
(when in test mode).
39
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
CXM Controls
CXM Control Start-up Operation
Table 12: Nominal resistance at
The control will not operate until all inputs and safety controls
various temperatures
are checked for normal conditions. The compressor will have a
Temp
Temp Resistance
Temp
5 minute anti-short cycle delay at power-up. The Ärst time after
(kOhm)
(°C)
(°F)
(°C)
power-up that there is a call for compressor, the compressor will
follow a 5 to 80 second random start delay. After the random
start delay and anti-short cycle delay, the compressor relay will
be energized. On all subsequent compressor calls, the random
start delay is omitted.
Table 11: Unit Operation
T-stat signal
1
2
GT-PX
Variable Speed Air Handler
G
Fan only
G, Y or Y1
Stage 1 heating
G, Y1, Y2
Stage 2 heating
G, Y1, Y2, W
Stage 3 heating
G, W
Emergency heat
G, Y or Y1, O
Stage 1 cooling
G, Y1, Y2, O
Stage 2 cooling
1
1
1
2
2
Stage 1 = 1st stage compressor, 1st stage fan operation
Stage 2 = 2nd stage compressor, 2nd stage fan operation
Stage 3 = 2nd stage compressor, auxiliary electric heat,
2nd or 3rd stage fan operation (depending on fan
settings)
Stage 1 = 1st stage compressor, 1st stage fan operation,
reversing valve
Stage 2 = 2nd stage compressor, 2nd stage fan operation,
reversing valve
CXM Thermostat Details
Thermostat Compatibility - Most all heat pump thermostats
can be used with the CXM control. However Heat/Cool
stats are NOT compatible with the CXM.
Anticipation Leakage Current - Maximum leakage current
for "Y" is 50 mA and for "W" is 20mA. Triacs can be used
if leakage current is less than above. Thermostats with
anticipators can be used if anticipation current is less than
that speciÄed above.
Thermostat Signals • "Y" and "W" have a 1 second recognition time when
being activated or being removed.
• "O" and "G" are direct pass through signals but are
monitored by the micro processor.
• "R" and "C" are from the transformer.
• "AL1" and "AL2" originate from the alarm relay.
• "A" is paralleled with the compressor output for use
with well water solenoid valves.
• The "Y" 1/4" quick connect is a connection point to the
"Y" input terminal P1 for factory use. This "Y" terminal
can be used to drive panel mounted relays such as the
loop pump relay.
40
Temp
(°F)
Resistance
(kOhm)
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Unit Starting and Operating Conditions
Operating Limits
Environment – GT-PX units are designed for indoor installation only. Never install in areas subject to freezing or where humidity
levels could cause cabinet condensation (such as unconditioned spaces subject to 100% outside air). Power Supply – A voltage
variation of +/– 10% of nameplate utilization voltage is acceptable. GT-PE units are designed for conditions where ambient air
is below freezing.
Determination of operating limits is dependent primarily upon three factors: 1) return air temperature. 2) water temperature,
and 3) ambient temperature. When any one of these factors is at minimum or maximum levels, the other two factors should
be at normal levels to insure proper unit operation. Extreme variations in temperature and humidity and/or corrosive water or
air will adversely affect unit performance, reliability, and service life. Consult 11a for operating limits.
Table 13a: Building Operating Limits
Operating Limits
Air Limits
Min. ambient air, DB
Rated ambient air, DB
Max. ambient air, DB
Min. entering air, DB/WB
Rated entering air, DB/WB
Max. entering air, DB/WB
Water Limits
Min. entering water
Normal entering water
Max. entering water
Normal Water Flow
TTS
GT-PX
Cooling
Heating
TTP
GT-PE
Operating Limits
Air Limits
45ºF [7ºC]
39ºF [4ºC]
Min. ambient air, DB
80.6ºF [27ºC]
68ºF [20ºC]
Rated ambient air, DB
110ºF [43ºC]
85ºF [29ºC]
Max. ambient air, DB
60/45ºF [16/7ºC]
40ºF [4.4ºC]
Min. entering air, DB/WB
80.6/66.2ºF [27/19ºC]
68ºF [20ºC]
Rated entering air, DB/WB
100/75ºF [38/24ºC]
80ºF [27ºC]
Max. entering air, DB/WB
Water Limits
30ºF [-1ºC]
20ºF [-6.7ºC]
Min. entering water
50-110ºF [10-43ºC]
30-70ºF [-1 to 21ºC] Normal entering water
120ºF [49ºC]
90ºF [32ºC]
Max. entering water
1.5 to 3.0 gpm / ton
Normal Water Flow
[1.6 to 3.2 l/m per kW]
Cooling
Heating
-10ºF [-23ºC]
80.6ºF [27ºC]
110ºF [43ºC]
60/45ºF [16/7ºC]
80.6/66.2ºF [27/19ºC]
100/75ºF [38/24ºC]
-10ºF [-23ºC]
68ºF [20ºC]
85ºF [29ºC]
40ºF [4.4ºC]
68ºF [20ºC]
80ºF [27ºC]
30ºF [-1ºC]
20ºF [-6.7ºC]
50-110ºF [10-43ºC]
30-70ºF [-1 to 21ºC]
120ºF [49ºC]
90ºF [32ºC]
1.5 to 3.0 gpm / ton
[1.6 to 3.2 l/m per kW]
Rev.: 9 June, 2009P
Created: 23 June, 2009B
Commissioning Limits
Consult Table 13b for the particular model. Starting conditions vary depending upon model and are based upon the following
notes:
Notes:
1.
Commissioning limits in Table 13b are not normal or continuous operating conditions. Minimum/maximum limits are
start-up conditions to bring the building space up to occupancy temperatures. Units are not designed to operate under
these conditions on a regular basis.
2.
Voltage utilization range complies with AHRI Standard 110.
Table 11b: Building Commissioning Limits
Commissioning Limits
Air Limits
Min. ambient air, DB
Rated ambient air, DB
Max. ambient air, DB
Min. entering air, DB/WB
Rated entering air, DB/WB
Max. entering air, DB/WB
Water Limits
Min. entering water
Normal entering water
Max. entering water
Normal Water Flow
GT-PX
TTS
Cooling
Heating
Commissioning Limits
Air Limits
45ºF [7ºC]
39ºF [4ºC]
Min. ambient air, DB
80.6ºF [27ºC]
68ºF [20ºC]
Rated ambient air, DB
110ºF [43ºC]
85ºF [29ºC]
Max. ambient air, DB
50ºF [10ºC]
40ºF [4.5ºC]
Min. entering air, DB/WB
80.6/66.2ºF [27/19ºC]
68ºF [20ºC]
Rated entering air, DB/WB
110/83ºF [43/28ºC]
80ºF [27ºC]
Max. entering air, DB/WB
Water Limits
30ºF [-1ºC]
20ºF [-6.7ºC]
Min. entering water
50-110ºF [10-43ºC]
30-70ºF [-1 to 21ºC] Normal entering water
120ºF [49ºC]
90ºF [32ºC]
Max. entering water
1.5 to 3.0 gpm / ton
Normal Water Flow
[1.6 to 3.2 l/m per kW]
Rev.: 9 June, 2009P
TTP
GT-PE
Cooling
Heating
-10ºF [-23ºC]
80.6ºF [27ºC]
110ºF [43ºC]
50ºF [10ºC]
80.6/66.2ºF [27/19ºC]
110/83ºF [43/28ºC]
-10ºF [-23ºC]
68ºF [20ºC]
85ºF [29ºC]
40ºF [4.5ºC]
68ºF [20ºC]
80ºF [27ºC]
30ºF [-1ºC]
20ºF [-6.7ºC]
50-110ºF [10-43ºC]
30-70ºF [-1 to 21ºC]
120ºF [49ºC]
90ºF [32ºC]
1.5 to 3.0 gpm / ton
[1.6 to 3.2 l/m per kW]
Created: 23 June, 2009B
41
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Unit Starting and Operating Conditions
Unit and System Checkout
BEFORE POWERING SYSTEM, please check the following:
UNIT CHECKOUT
φ Balancing/shutoff valves: Insure that all isolation valves
are open and water control valves are wired.
φ Line voltage and wiring: Verify that voltage is within
an acceptable range for the unit and wiring and fuses/
breakers are properly sized. Verify that low voltage wiring
is complete.
φ Unit control transformer: Insure that transformer has the
properly selected voltage tap. Residential 208-230V units
are factory wired for 230V operation unless speciÄed
otherwise.
φ Loop/water piping is complete and purged of air. Water/
piping is clean.
φ Antifreeze has been added if necessary.
φ Entering water and air: Insure that entering water and air
temperatures are within operating limits of Table 13b.
φ Low water temperature cutout: Verify that low water
temperature cut-out on the CXM/DXM control is properly
set.
φ Unit fan: Manually rotate fan to verify free rotation and
insure that blower wheel is secured to the motor shaft.
Be sure to remove any shipping supports if needed.
DO NOT oil motors upon start-up. Fan motors are preoiled at the factory. Check unit fan speed selection and
compare to design requirements.
φ Condensate line: Verify that condensate line is open and
properly pitched toward drain.
φ HWG pump is disconnected unless piping is completed
and air has been purged from the system.
φ Water Åow balancing: Record inlet and outlet water
temperatures for each heat pump upon startup. This
check can eliminate nuisance trip outs and high velocity
water Åow that could erode heat exchangers.
φ Unit air coil and Älters: Insure that Älter is clean and
accessible. Clean air coil of all manufacturing oils.
φ Unit controls: Verify that CXM Äeld selection options are
properly set. Low voltage wiring is complete.
φ Blower speed is set.
φ Service/access panels are in place.
ѥCAUTION! ѥ
CAUTION! To avoid equipment damage, DO NOT allow
system water pressure to exceed 100 psi when using
the GT-PE Outdoor Compressor Section. The expansion
tank in the GT-PE has a maximum working water
pressure of 100 psi. Any pressure in excess of 100 psi
may damage the expansion tank.
SYSTEM CHECKOUT
φ System water temperature: Check water temperature
for proper range and also verify heating and cooling set
points for proper operation.
φ System pH: Check and adjust water pH if necessary to
42
φ
φ
φ
φ
φ
maintain a level between 6 and 8.5. Proper pH promotes
longevity of hoses and Ättings (see Table 4).
System Åushing: Verify that all air is purged from the
system. Air in the system can cause poor operation or
system corrosion. Water used in the system must be
potable quality initially and clean of dirt, piping slag,
and strong chemical cleaning agents. Some antifreeze
solutions may require distilled water.
Flow Controller pump(s): Verify that the pump(s) is wired,
purged of air, and in operating condition.
System controls: Verify that system controls function and
operate in the proper sequence.
Low water temperature cutout: Verify that low water
temperature cut-out controls are set properly
(FP1 - JW3).
Miscellaneous: Note any questionable aspects of
the installation.
ѥCAUTION! ѥ
CAUTION! Verify that ALL water control valves are open
and allow water Àow prior to engaging the compressor.
Freezing of the coax or water lines can permanently
damage the heat pump.
ѥCAUTION! ѥ
CAUTION! To avoid equipment damage, DO NOT
leave system ¿lled in a building without heat during the
winter unless antifreeze is added to the water loop. Heat
exchangers never fully drain by themselves and will
freeze unless winterized with antifreeze.
Unit Start-up Procedure
1. Always deactivate the HWG (on units equipped with an
HWG) before completing the following steps.
2. Turn the thermostat fan position to “ON.” Blower should
start.
3. Balance air Åow at registers.
4. Adjust all valves to their full open position. Turn on the
line power to all heat pump units.
5. Room temperature should be within the minimummaximum ranges of Table 13b. During start-up checks,
loop water temperature entering the heat pump should
be between 30°F [-1°C] and 95°F [35°C].
6. Two factors determine the operating limits of water
source heat pumps, (a) return air temperature, and (b)
water temperature. When any one of these factors is at a
minimum or maximum level, the other factor must be at
normal level to insure proper unit operation.
a. Adjust the unit thermostat to the warmest setting.
Place the thermostat mode switch in the “COOL”
position. Slowly reduce thermostat setting until the
compressor activates.
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Unit Start-Up Procedure
b. Check for cool air delivery at the unit grille within a
few minutes after the unit has begun to operate.
Note: Units have a Äve minute time delay in the
control circuit that can be bypassed on the CXM/
DXM control board as shown below in Figure 20. See
controls description for details.
c. Verify that the compressor is on and that the water
Åow rate is correct by measuring pressure drop
through the heat exchanger using the P/T plugs and
comparing to Table 14.
d. Check the elevation and cleanliness of the
condensate lines. Dripping may be a sign of a
blocked line. Check that the condensate trap is Älled
to provide a water seal.
e. Refer to Table 15. Check the temperature of both
entering and leaving water. If temperature is within
range, proceed with the test. If temperature is
outside of the operating range, check refrigerant
pressures and compare to Tables 16a through 16d.
Verify correct water Åow by comparing unit pressure
drop across the heat exchanger versus the data in
Table 14. Heat of rejection (HR) can be calculated
and compared to catalog data capacity pages. The
formula for HR for systems with water is as follows:
HR = TD x GPM x 500, where TD is the temperature
difference between the entering and leaving water,
and GPM is the Åow rate in U.S. GPM, determined
by comparing the pressure drop across the heat
exchanger to Table 14.
f. Check air temperature drop across the air coil when
compressor is operating. Air temperature drop should
be between 15°F and 25°F [8°C and 14°C].
g. Turn thermostat to “OFF” position. A hissing noise
indicates proper functioning of the reversing valve.
7. Allow Äve (5) minutes between tests for pressure to
equalize before beginning heating test.
a. Adjust the thermostat to the lowest setting. Place the
thermostat mode switch in the “HEAT” position.
b. Slowly raise the thermostat to a higher temperature
until the compressor activates.
c. Check for warm air delivery within a few minutes after
the unit has begun to operate.
d. Refer to Table 15. Check the temperature of both
entering and leaving water. If temperature is within
range, proceed with the test. If temperature is
outside of the operating range, check refrigerant
pressures and compare to Tables 16a through 16d
Verify correct water Åow by comparing unit pressure
drop across the heat exchanger versus the data in
Table 14. Heat of extraction (HE) can be calculated
and compared to submittal data capacity pages. The
formula for HE for systems with water is as follows:
HE = TD x GPM x 500, where TD is the temperature
difference between the entering and leaving water,
and GPM is the Åow rate in U.S. GPM, determined
by comparing the pressure drop across the heat
exchanger to Table 14.
e. Check air temperature rise across the air coil when
compressor is operating. Air temperature rise should
be between 20°F and 30°F [11°C and 17°C].
f. Check for vibration, noise, and water leaks.
8. If unit fails to operate, perform troubleshooting analysis
(see troubleshooting section). If the check described
fails to reveal the problem and the unit still does not
operate, contact a trained service technician to insure
proper diagnosis and repair of the equipment.
9. When testing is complete, set system to maintain
desired comfort level.
10. BE CERTAIN TO FILL OUT AND RETURN ALL
WARRANTY REGISTRATION PAPERWORK.
Note: If performance during any mode appears abnormal,
refer to the CXM section or troubleshooting section of this
manual. To obtain maximum performance, the air coil should
be cleaned before start-up. A 10% solution of dishwasher
detergent and water is recommended.
ѥWARNING! ѥ
WARNING! When the disconnect switch is closed, high
voltage is present in some areas of the electrical panel.
Exercise caution when working with energized equipment.
ѥCAUTION! ѥ
CAUTION! Verify that ALL water control valves are open
and allow water Àow prior to engaging the compressor.
Freezing of the coax or water lines can permanently
damage the heat pump.
Figure 29: Test Mode Pins
Short test pins together
to enter Test Mode and
speed-up timing and delays
for 20 minutes.
43
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Unit Operating Conditions
Table 12: Two-Stage Puron® Compressor Section Coax
Water Pressure Drop
Model
026
038
049
064
GPM
4.0
6.0
7.0
8.0
4.0
6.0
8.0
9.0
5.5
8.3
11.0
12.0
7.0
10.5
14.0
15.0
Table 15: Water Temperature Change Through Heat
Exchanger
Pressure Drop (psi)
30°F
50°F
70°F
90°F
1.5
3.1
4.1
5.1
1.2
2.6
4.5
5.7
1.1
2.2
3.9
4.5
0.5
1.9
3.9
4.8
1.3
2.6
3.4
4.3
1.0
2.5
4.2
5.2
0.9
2.1
3.6
4.2
0.3
1.8
3.5
4.3
1.1
2.3
3.0
3.8
0.8
2.3
4.0
4.8
0.8
2.0
3.2
3.8
0.2
1.7
3.2
3.9
1.0
2.1
2.7
3.4
0.6
2.1
3.7
4.4
0.7
1.8
3.1
3.5
0.1
1.6
2.9
3.5
Table 14a: Size 026 Two-Stage Puron® Typical Unit Operating Pressures and Temperatures
Full Load Cooling - without HWG active
Full Load Heating - without HWG active
Entering
Water
Temp °F
Water
Flow
GPM/
ton
Suction
Pressure
PSIG
Discharge
Pressure
PSIG
Superheat
Subcooling
Water Temp
Rise °F
Air Temp
Drop °F
DB
Suction
Pressure
PSIG
Discharge
Pressure
PSIG
Superheat
Subcooling
Water Temp
Drop °F
Air Temp
Rise °F
DB
30*
1.5
2.25
3
122-132
122-132
122-132
159-179
146-166
132-152
13-18
13-18
14-19
9-14
7-12
7-12
16.7-18.7
12.3-14.3
7.9-9.9
18-24
19-25
19-25
77-87
79-89
82-92
278-298
280-300
282-302
4-9
4-9
4-9
10-15
10-15
10-15
5.9-7.9
4.2-6.2
2.7-4.7
18-24
19-25
20-26
50
1.5
2.25
3
132-142
132-142
132-142
186-206
172-192
158-178
8-13
8-13
8-13
8-13
6-11
6-11
16.3-18.3
12.1-14.1
7.8-9.8
18-24
19-25
19-25
107-117
111-121
115-125
314-334
315-335
317-337
6-11
6-11
6-11
13-18
13-18
13-18
8.9-10.9
6.7-8.7
4.5-6.5
25-31
26-32
26-32
70
1.5
2.25
3
139-149
139-149
139-149
281-301
267-287
253-273
7-12
7-12
7-12
8-13
8-13
7-12
15.7-17.7
11.6-13.6
7.6-9.6
18-24
18-24
18-24
139-149
145-155
152-162
350-370
352-372
354-374
7-12
7-12
7-12
15-20
15-20
15-20
11.3-13.3
8.5-10.5
5.8-7.8
31-38
32-39
32-39
90
1.5
2.25
3
141-151
141-151
141-151
374-394
360-380
346-366
7-12
7-12
7-12
9-14
9-14
8-13
14.6-16.6
10.7-12.7
6.9-8.9
17-23
17-23
17-23
177-187
181-191
186-196
392-412
397-417
402-422
9-14
10-15
11-16
17-22
17-22
17-22
14.4-16.4
10.8-12.8
7.1-9.1
37-45
38-46
38-46
110
1.5
2.25
3
145-155
145-155
145-155
473-493
458-478
441-461
7-12
7-12
7-12
10-15
10-15
9-14
13.6-15.6
9.9-11.9
6.2-8.2
16-22
16-22
16-22
Operation Not Recommended
*Based on 15% methanol antifreeze solution
Table 14b: Size 038 Two-Stage Puron® Typical Unit Operating Pressures and Temperatures
Full Load Cooling - without HWG active
Entering
Water
Temp °F
Water
Flow
GPM/
ton
Suction
Pressure
PSIG
Discharge
Pressure
PSIG
Superheat
Subcooling
30*
1.5
2.25
3
122-132
121-131
121-131
153-173
145-165
135-155
18-23
18-23
18-23
50
1.5
2.25
3
131-141
130-140
130-140
222-242
208-228
194-214
70
1.5
2.25
3
138-148
137-147
137-147
90
1.5
2.25
3
110
1.5
2.25
3
Water Temp
Rise °F
Suction
Pressure
PSIG
Discharge
Pressure
PSIG
Superheat
Subcooling
Water Temp
Drop °F
Air Temp
Rise °F
DB
9-14
8-13
8-13
22.1-24.1
16.8-18.8
10.5-12.5
19-25
20-26
20-26
71-81
75-85
78-88
263-283
267-287
270-290
5-10
5-10
5-10
2-5
2-5
2-5
8.1-10.1
5.9-7.9
3.7-5.7
17-23
18-24
19-25
13-18
13-18
14-19
10-15
9-14
9-14
21.9-23.9
16.1-18.1
10.3-12.3
19-25
20-26
20-26
103-113
107-117
112-122
292-312
296-316
301-321
6-11
6-11
6-11
2.5-7
2.5-7
2.5-7
11.5-13.5
8.6-10.6
5.7-7.7
23-29
24-30
24-30
299-319
280-300
263-283
8-13
8-13
8-13
13-18
12-17
12-17
21.5-23.5
15.8-17.8
10-12
19-25
20-26
20-26
134-144
140-150
146-156
322-342
328-358
334-354
7-12
7-12
7-12
2.5-7
2.5-7
2.5-7
14.5-16.5
11.1-13.1
7.7-9.7
28-35
29-36
30-37
142-152
142-152
142-152
388-408
367-387
347-367
6-11
7-12
7-12
13-18
8-13
8-13
20.5-22.5
14.9-16.9
9.3-11.3
18-24
18-24
18-24
172-182
184-194
196-206
360-380
369-389
378-398
8-13
8-13
8-13
2.5-7
2.5-7
2.5-7
20.5-22.5
15-17
10-12
36-44
37-45
39-47
147-157
147-157
147-157
486-506
465-475
444-464
6-11
7-12
7-12
13-18
8-13
8-13
19-21
14-16
9-11
18-24
18-24
18-24
*Based on 15% methanol antifreeze solution
44
Full Load Heating - without HWG active
Air Temp
Drop °F
DB
Operation Not Recommended
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Unit Operating Conditions
Table 14c: Size 049 Two-Stage Puron® Typical Unit Operating Pressures and Temperatures
Full Load Cooling - without HWG active
Entering
Water
Temp °F
Water
Flow
GPM/
ton
Suction
Pressure
PSIG
Discharge
Pressure
PSIG
Superheat
Subcooling
30*
1.5
2.25
3
112-122
111-121
111-121
187-207
167-187
147-167
18-23
18-23
18-23
50
1.5
2.25
3
125-135
123-133
122-132
245-265
227-247
208-228
1.5
2.25
3
133-143
132-142
131-141
90
1.5
2.25
3
110
1.5
2.25
3
70
Full Load Heating - without HWG active
Water Temp
Rise °F
Air Temp
Drop °F
DB
Suction
Pressure
PSIG
Discharge
Pressure
PSIG
Superheat
Subcooling
Water Temp
Drop °F
Air Temp
Rise °F
DB
23-28
21-26
20-25
20.7-22.7
15.5-17.5
10.2-12.2
19-25
19-25
19-25
66-76
69-79
72-82
261-281
264-284
267-287
8-13
8-13
8-13
5-10
5-10
5-10
8-10
6-8
4-6
18-24
19-25
19-25
13-18
13-18
14-19
19-24
18-23
16-21
20.9-22.9
15.6-17.6
10.2-12.2
20-26
20-26
20-26
93-103
98-108
103-113
289-309
295-315
301-321
7-12
7-12
7-12
5-10
5-10
5-10
11.5-13.5
8.7-10.7
5.9-7.9
23-29
24-30
25-31
314-334
294-314
274-294
9-14
9-14
10-15
17-22
16-21
14-19
20.5-22.5
15.2-17.2
9.9-11.9
20-26
20-26
20-26
123-133
130-140
137-147
319-339
329-349
336-356
7-12
7-12
7-12
5-10
5-10
5-10
15-17
11.5-13.5
7.9-9.9
28-35
29-36
30-37
138-148
137-147
136-146
401-421
379-399
357-377
8-13
8-13
9-14
16-21
15-20
13-18
19.2-21.2
14.3-16.3
9.3-11.3
19-25
19-25
19-25
167-177
177-187
187-197
365-385
374-394
388-408
7-12
7-12
7-12
5-10
5-10
5-10
19.6-21.6
15-17
10.3-12.3
37-45
38-46
39-47
144-154
143-153
142-152
502-522
477-497
452-472
8-13
8-13
9-14
14-19
13-18
12-17
18-20
13.3-15.3
8.5-10.5
18-24
18-24
18-24
Operation Not Recommended
*Based on 15% methanol antifreeze solution
Table 14d: Size 064 Two-Stage Puron® Typical Unit Operating Pressures and Temperatures
Full Load Cooling - without HWG active
Entering
Water
Temp °F
Water
Flow
GPM/
ton
Suction
Pressure
PSIG
Discharge
Pressure
PSIG
Superheat
Subcooling
30*
1.5
2.25
3
117-127
116-126
115-125
160-180
133-153
125-145
16-21
17-22
18-23
50
1.5
2.25
3
126-136
124-134
123-133
228-248
212-232
195-215
70
1.5
2.25
3
130-140
129-139
128-138
90
1.5
2.25
3
110
1.5
2.25
3
Full Load Heating - without HWG active
Water Temp
Rise °F
Air Temp
Drop °F
DB
Suction
Pressure
PSIG
Discharge
Pressure
PSIG
Superheat
Subcooling
Water Temp
Drop °F
Air Temp
Rise °F
DB
8-13
6-11
5-10
17.5-19.5
11.9-13.9
6.3-8.3
16-22
16-22
16-22
66-76
69-79
72-82
282-302
285-305
289-309
9-15
9-15
9-15
8-13
8-13
9-14
8-10
6-8
4-6
21-27
21-27
22-28
8-13
11-16
14-19
8-13
6-11
5-10
19.8-21.8
14.2-16.2
8.5-10.5
20-26
20-26
20-26
95-105
100-110
105-115
318-338
321-341
324-344
9-15
9-15
9-15
12-17
12-17
12-17
11.3-13.3
8.5-10.5
5.7-7.7
27-33
28-34
30-36
305-325
286-306
266-286
8-13
9-14
11-16
10-15
9-14
7-12
20.3-22.3
14.8-16.8
9.3-11.3
21-27
21-27
21-27
128-138
133-143
139-149
360-380
364-384
368-388
8-14
8-14
8-14
12-17
12-17
12-17
14-16
10.6-12.6
7.3-9.3
33-38
34-40
35-41
133-143
132-142
132-142
398-418
376-396
354-374
8-13
8-13
8-13
10-15
9-14
7-12
19.4-21.4
14.1-16.1
8.8-10.8
20-26
20-26
20-26
173-183
177-187
182-192
407-427
411-431
415-435
8-14
8-14
8-14
13-18
13-18
14-19
18.2-20.2
13.9-15.9
9.6-11.6
42-50
43-51
44-52
138-148
137-147
136-146
505-525
483-503
459-479
6-11
6-11
6-11
10-15
9-14
8-13
18.3-20.3
13.3-15.3
8.3-10.3
19-25
19-25
19-25
Operation Not Recommended
*Based on 15% methanol antifreeze solution
Antifreeze Correction Table
Cooling
Heating
EWT 90°F
EWT 30°F
WPD
Corr. Fct.
EWT 30°F
Antifreeze Type
Antifreeze
%
Water
0
5
0.995
0.995
1.003
0.989
0.997
1.070
Propylene Glycol
15
0.986
0.986
1.009
0.968
0.990
1.210
25
0.978
0.978
1.014
0.947
0.983
1.360
5
0.997
0.997
1.002
0.989
0.997
1.070
15
0.990
0.990
1.007
0.968
0.990
1.160
25
0.982
0.982
1.012
0.949
0.984
1.220
5
0.998
0.998
1.002
0.981
0.994
1.140
15
0.994
0.994
1.005
0.944
0.983
1.300
25
0.986
0.986
1.009
0.917
0.974
1.360
5
0.998
0.998
1.002
0.993
0.998
1.040
15
0.994
0.994
1.004
0.980
0.994
1.120
25
0.988
0.988
1.008
0.966
0.990
1.200
Methanol
Ethanol
Ethylene Glycol
Total Cap
Sens Cap
Power
Htg Cap
Power
1.000
1.000
1.000
1.000
1.000
1.000
45
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Preventive Maintenance
Water Coil Maintenance
(Direct ground water applications only)
If the system is installed in an area with a known high mineral
content (125 P.P.M. or greater) in the water, it is best to
establish a periodic maintenance schedule with the owner
so the coil can be checked regularly. Consult the well water
applications section of this manual for a more detailed water
coil material selection. Should periodic coil cleaning be
necessary, use standard coil cleaning procedures, which are
compatible with the heat exchanger material and copper
water lines. Generally, the more water Åowing through the
unit, the less chance for scaling. Therefore, 1.5 gpm per
ton [2.0 l/m per kW] is recommended as a minimum Åow.
Minimum Åow rate for entering water temperatures below
50°F [10°C] is 2.0 gpm per ton [2.6 l/m per kW].
Water Coil Maintenance
(All other water loop applications)
Generally water coil maintenance is not needed for closed
loop systems. However, if the piping is known to have
high dirt or debris content, it is best to establish a periodic
maintenance schedule with the owner so the water coil
can be checked regularly. Dirty installations are typically
the result of deterioration of iron or galvanized piping or
components in the system. Open cooling towers requiring
heavy chemical treatment and mineral buildup through water
use can also contribute to higher maintenance. Should
periodic coil cleaning be necessary, use standard coil
cleaning procedures, which are compatible with both the
heat exchanger material and copper water lines. Generally,
the more water Åowing through the unit, the less chance for
scaling. However, Åow rates over 3 gpm per ton (3.9 l/m per
kW) can produce water (or debris) velocities that can erode
the heat exchanger wall and ultimately produce leaks.
Hot Water Generator Coils
See water coil maintenance for ground water units. If the
potable water is hard or not chemically softened, the high
temperatures of the desuperheater will tend to scale even
quicker than the water coil and may need more frequent
inspections. In areas with extremely hard water, a HWG is
not recommended.
Filters
Filters must be clean to obtain maximum performance.
Filters should be inspected every month under normal
operating conditions and be replaced when necessary. Units
should never be operated without a Älter.
Washable, high efÄciency, electrostatic Älters, when dirty,
can exhibit a very high pressure drop for the fan motor and
reduce air Åow, resulting in poor performance. It is especially
important to provide consistent washing of these Älters (in
the opposite direction of the normal air Åow) once per month
using a high pressure wash similar to those found at selfserve car washes.
46
Condensate Drain
In areas where airborne bacteria may produce a “slimy”
substance in the drain pan, it may be necessary to treat the
drain pan chemically with an algaecide approximately every
three months to minimize the problem. The condensate pan
may also need to be cleaned periodically to insure indoor
air quality. The condensate drain can pick up lint and dirt,
especially with dirty Älters. Inspect the drain twice a year to
avoid the possibility of plugging and eventual overÅow.
Compressor
Conduct annual amperage checks to insure that amp draw is
no more than 10% greater than indicated on the serial plate
data.
Fan Motors
Consult air handler I.O.M. for maintenance requirements.
Air Coil
The air coil must be cleaned to obtain maximum
performance. Check once a year under normal operating
conditions and, if dirty, brush or vacuum clean. Care must
be taken not to damage the aluminum Äns while cleaning.
CAUTION: Fin edges are sharp.
Cabinet - “Indoor” Compressor Section
Do not allow water to stay in contact with the cabinet for
long periods of time to prevent corrosion of the cabinet sheet
metal. Generally, cabinets are set up from the Åoor a few
inches [7 - 8 cm] to prevent water from entering the cabinet.
The cabinet can be cleaned using a mild detergent.
Refrigerant System
To maintain sealed circuit integrity, do not install service
gauges unless unit operation appears abnormal. Reference
the operating charts for pressures and temperatures. Verify
that air and water Åow rates are at proper levels before
servicing the refrigerant circuit.
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Troubleshooting
General
If operational difÄculties are encountered, perform
the preliminary checks below before referring to the
troubleshooting charts.
• Verify that the unit is receiving electrical supply power.
• Make sure the fuses in the fused disconnect switches
are intact.
After completing the preliminary checks described above,
inspect for other obvious problems such as leaking
connections, broken or disconnected wires, etc. If everything
appears to be in order, but the unit still fails to operate
properly, refer to the “CXM Troubleshooting Process
Flowchart” or “Functional Troubleshooting Chart.”
CXM Board
CXM board troubleshooting in general is best summarized
as simply verifying inputs and outputs. After inputs and
outputs have been veriÄed, board operation is conÄrmed and
the problem must be elsewhere. Below are some general
guidelines for troubleshooting the CXM control.
Field Inputs
All inputs are 24VAC from the thermostat and can be veriÄed
using a volt meter between C and Y, G, O, W. 24VAC will be
present at the terminal (for example, between “Y” and “C”) if
the thermostat is sending an input to the CXM board.
Sensor Inputs
All sensor inputs are ‘paired wires’ connecting each component
to the board. Therefore, continuity on pressure switches, for
example can be checked at the board connector.
Test Mode
Test mode can be entered for 20 minutes by shorting the test
pins (see Figure 29). The CXM board will automatically exit
test mode after 20 minutes.
CXM Troubleshooting Process Flowchart/Functional
Troubleshooting Chart
The “CXM Troubleshooting Process Flowchart” is a quick
overview of how to start diagnosing a suspected problem,
using the fault recognition features of the CXM board. The
“Functional Troubleshooting Chart” on the following page is
a more comprehensive method for identifying a number of
malfunctions that may occur, and is not limited to just the
CXM controls. Within the chart are Äve columns:
• The “Fault” column describes the symptoms.
• Columns 2 and 3 identify in which mode the fault is likely
to occur, heating or cooling.
• The “Possible Cause column” identiÄes the most likely
sources of the problem.
• The “Solution” column describes what should be done to
correct the problem.
ѥWARNING! ѥ
WARNING! HAZARDOUS VOLTAGE! DISCONNECT
ALL ELECTRIC POWER INCLUDING REMOTE
DISCONNECTS BEFORE SERVICING.
Failure to disconnect power before servicing can cause
severe personal injury or death.
The thermistor resistance should be measured with the
connector removed so that only the impedance of the
thermistor is measured. If desired, this reading can be
compared to the thermistor resistance chart shown in
the CXM AOM manual. An ice bath can be used to check
calibration of the thermistor.
Outputs
The compressor relay is 24VAC and can be veriÄed using a
voltmeter. The fan signal is passed through the board to the
external fan relay (units with PSC motors only). The alarm
relay can either be 24VAC as shipped or dry contacts for use
with DDC controls by clipping the JW1 jumper. Electric heat
outputs are 24VDC “ground sinking” and require a volt meter
set for DC to verify operation. The terminal marked “24VDC”
is the 24VDC supply to the electric heat board; terminal “EH1”
is stage 1 electric heat; terminal “EH2” is stage 2 electric heat.
When electric heat is energized (thermostat is sending a “W”
input to the CXM controller), there will be 24VDC between
terminal “24VDC” and “EH1” (stage 1 electric heat) and/or
“EH2” (stage 2 electric heat). A reading of 0VDC between
“24VDC” and “EH1” or “EH2” will indicate that the CXM board
is NOT sending an output signal to the electric heat board.
47
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
CXM Process Flow Chart
ѥWARNING! ѥ
WARNING! HAZARDOUS VOLTAGE! DISCONNECT
ALL ELECTRIC POWER INCLUDING REMOTE
DISCONNECTS BEFORE SERVICING.
Failure to disconnect power before servicing can cause
severe personal injury or death.
Start
Did Unit
Attempt to
Start?
CXM Functional
Troubleshooting Flow Chart
No
Check Main
power (see power
problems)
Yes
Did Unit
Lockout at
Start-up?
No
See “ Unit
short
cycles”
Yes
Yes
Unit Short
Cycles?
No fault
shown
Check fault LED code
on control board
See HP
Fault
See
LP/LOC
Fault
See FP1
Fault
No
See “ Only
Fan Runs”
See “ Only
Comp
Runs”
Yes
Yes
Only Fan
Runs?
No
Only
Compressor
Runs?
No
See “ Does No
not Operate
in Clg”
Did unit lockout Yes
after a period of
operation?
No
Does unit
operate in
cooling?
Yes
Unit is OK!
‘See Performance
Troubleshooting’ for
further help
48
See FP2
Fault
See
Condensate
Fault
See Over/
Under
Voltage
Replace
CXM
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Functional Troubleshooting
Fault
Main power problems
HP Fault
Code 2
Htg Clg Possible Cause
Air temperature out of range in heating
Overcharged with refrigerant
Bad HP Switch
Insuf¿cient charge
X
Compressor pump down at start-up
Check charge and start-up water Àow.
X
Reduced or no water Àow in heating
X
X
Inadequate antifreeze level
Improper temperature limit setting (30°F vs
10°F [-1°C vs -2°C])
Water Temperature out of range
Bad thermistor
X
Reduced or no air Àow in cooling
X
X
X
X
Air Temperature out of range
Improper temperature limit setting (30°F vs
10°F [-1°C vs -12°C])
Bad thermistor
Blocked drain
Improper trap
X
Poor drainage
X
x
X
X
X
Moisture on sensor
Plugged air ¿lter
Restricted Return Air Flow
X
X
Under Voltage
X
X
X
X
Green Status LED Off
X
Reduced or no water Àow in cooling
X
Water Temperature out of range in cooling
Reduced or no air Àow in heating
X
High Pressure
LP/LOC Fault
Code 3
Solution
Check line voltage circuit breaker and disconnect.
Check for line voltage between L1 and L2 on the contactor.
Check for 24VAC between R and C on CXM/DXM'
Check primary/secondary voltage on transformer.
Check pump operation or valve operation/setting.
Check water Àow adjust to proper Àow rate.
Bring water temp within design parameters.
Check for dirty air ¿lter and clean or replace.
Check fan motor operation and airÀow restrictions.
Dirty Air Coil- construction dust etc.
Too high of external static. Check static vs blower table.
Bring return air temp within design parameters.
Check superheat/subcooling vs typical operating condition table.
Check switch continuity and operation. Replace.
Check for refrigerant leaks
X
X
X
X
X
X
X
Low Pressure / Loss of Charge
LT1 Fault
Code 4
Water coil low
temperature limit
X
X
X
LT2 Fault
Code 5
Air coil low
temperature limit
X
X
X
X
Condensate Fault
Code 6
Over/Under
Voltage Code 7
(Auto resetting)
Unit Performance Sentinel
Code 8
No Fault Code Shown
Unit Short Cycles
Only Fan Runs
X
Over Voltage
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Heating mode FP2>125°F [52°C]
Cooling Mode FP1>125°F [52°C] OR FP2<
40ºF [4ºC])
No compressor operation
Compressor overload
Control board
Dirty air ¿lter
Unit in "test mode"
Unit selection
Compressor overload
Thermostat position
Unit locked out
Compressor Overload
X
X
Thermostat wiring
X
Check pump operation or water valve operation/setting.
Plugged strainer or ¿lter. Clean or replace..
Check water Àow adjust to proper Àow rate.
Check antifreeze density with hydrometer.
Clip JW3 jumper for antifreeze (10°F [-12°C]) use.
Bring water temp within design parameters.
Check temp and impedance correlation per chart
Check for dirty air ¿lter and clean or replace.
Check fan motor operation and airÀow restrictions.
Too high of external static. Check static vs blower table.
Too much cold vent air? Bring entering air temp within design parameters.
Normal airside applications will require 30°F [-1°C] only.
Check temp and impedance correlation per chart.
Check for blockage and clean drain.
Check trap dimensions and location ahead of vent.
Check for piping slope away from unit.
Check slope of unit toward outlet.
Poor venting. Check vent location.
Check for moisture shorting to air coil.
Replace air ¿lter.
Find and eliminate restriction. Increase return duct and/or grille size.
Check power supply and 24VAC voltage before and during operation.
Check power supply wire size.
Check compressor starting. Need hard start kit?
Check 24VAC and unit transformer tap for correct power supply voltage.
Check power supply voltage and 24VAC before and during operation.
Check 24VAC and unit transformer tap for correct power supply voltage.
Check for poor air Àow or overcharged unit.
Check for poor water Àow, or air Àow.
See "Only Fan Operates".
Check and replace if necessary.
Reset power and check operation.
Check and clean air ¿lter.
Reset power or wait 20 minutes for auto exit.
Unit may be oversized for space. Check sizing for actual load of space.
Check and replace if necessary
Ensure thermostat set for heating or cooling operation.
Check for lockout codes. Reset power.
Check compressor overload. Replace if necessary.
Check thermostat wiring at heat pump. Jumper Y and R for compressor operation
in test mode.
49
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Functional Troubleshooting
Only Compressor Runs
X
X
X
X
X
X
X
X
Fan motor
X
X
Thermostat wiring
X
Reversing valve
X
X
Thermostat setup
Thermostat wiring
X
Thermostat wiring
Unit Doesn’t Operate
in Cooling
Thermostat wiring
Fan motor relay
Check G wiring at heat pump. Jumper G and R for fan operation
Jumper G and R for fan operation. Check for Line voltage across BR contacts.
Check fan power enable relay operation (if present).
Check for line voltage at motor. Check capacitor.
Check thermostat wiring at heat pump. Jumper Y and R for compressor operation
in test mode
Set for cooling demand and check 24VAC on RV coil and at CXM/DXM board.
If RV is stuck, run high pressure up by reducing water Àow and while operating
engage and disengage RV coil voltage to push valve.
Check for ‘O’ RV setup not ‘B’.
Check O wiring at heat pump. Jumper O and R for RV coil ‘click’.
Put thermostat in cooling mode. Check 24 VAC on O (check between C and
O); check for 24 VAC on W (check between W and C). There should be voltage
on O, but not on W. If voltage is present on W, thermostat may be bad or wired
incorrectly.
Performance Troubleshooting
Performance Troubleshooting
Htg Clg Possible Cause
X
X
Solution
Dirty ¿lter
Replace or clean.
Reduced or no air Àow in heating
Check fan motor operation and airÀow restrictions.
Check for dirty air ¿lter and clean or replace.
X
Too high of external static. Check static vs. blower table.
Check for dirty air ¿lter and clean or replace.
X
Reduced or no air Àow in cooling
Check fan motor operation and airÀow restrictions.
Too high of external static. Check static vs. blower table.
Insuf¿cient capacity/ Not
cooling or heating
Check supply and return air temperatures at the unit and at distant duct registers
if signi¿cantly different, duct leaks are present.
X
X
Leaky duct work
X
X
Low refrigerant charge
Check superheat and subcooling per chart.
X
X
Restricted metering device
Check superheat and subcooling per chart. Replace.
X
Defective reversing valve
Perform RV touch test.
X
X
Thermostat improperly located
Check location and for air drafts behind stat.
X
X
Unit undersized
Recheck loads & sizing. Check sensible clg. load and heat pump capacity.
X
X
Scaling in water heat exchanger
Perform scaling check and clean if necessary.
X
X
Inlet water too hot or too cold
Check load, loop sizing, loop back¿ll, ground moisture.
Reduced or no air Àow in heating
Check fan motor operation and air Àow restrictions.
Check for dirty air ¿lter and clean or replace.
X
Too high of external static. Check static vs. blower table.
High Head Pressure
Check pump operation or valve operation/setting.
X
Reduced or no water Àow in cooling
X
Inlet water too hot
Check load, loop sizing, loop back¿ll, ground moisture.
X
Check water Àow. Adjust to proper Àow rate.
Air temperature out of range in heating
Bring return air temperature within design parameters.
X
Scaling in water heat exchanger
Perform scaling check and clean if necessary.
X
X
Unit overcharged
Check superheat and subcooling. Re-weigh in charge.
X
X
Non-condensables in system
Vacuum system and re-weigh in charge.
X
X
Restricted metering device.
Check superheat and subcooling per chart. Replace.
Check pump operation or water valve operation/setting.
X
Reduced water Àow in heating.
Plugged strainer or ¿lter. Clean or replace.
X
Water temperature out of range.
Bring water temperature within design parameters.
X
Reduced air Àow in cooling.
Check fan motor operation and air Àow restrictions.
X
Air temperature out of range
Too much cold vent air? Bring entering air temperature within design parameters.
Insuf¿cient charge
Check for refrigerant leaks.
Check water Àow. Adjust to proper Àow rate.
Check for dirty air ¿lter and clean or replace.
Low Suction Pressure
Too high of external static. Check static vs. blower table.
X
Low Discharge Air Temperature
in Heating
High humidity
50
X
X
Too high of air Àow
Check fan motor speed selection and air Àow chart.
X
Poor performance
See ‘Insuf¿cient Capacity’
X
Too high of air Àow
Check fan motor speed selection and airÀow chart.
X
Unit oversized
Recheck loads & sizing. Check sensible clg load and heat pump capacity.
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Troubleshooting Form
&XVWRPHUBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
$QWLIUHH]HBBBBBBBBBBBBBBBBB
0RGHOBBBBBBBBBBBBBBBBBBBBBBBB6HULDOBBBBBBBBBBBBBBBB /RRSW\SHBBBBBBBBB
&RPSODLQW BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
+($7,1*&<&/($1$/<6,6
$,5+$1'/(56(&7,21&2035(66256(&7,21
36,
5HIULJHUDQW7\SH
Puron®
+)&$
ƒ)
6$7
ƒ)
$,5
&2,/
68&7,21
ƒ)
&2035(6625
&22/,1*
(;3$16,21
9$/9(
+($7,1*
(;3$16,21
9$/9(
&2$;
',6&+$5*(
+:*
ƒ)
/RRNXSSUHVVXUHGURSLQ
,20RUVSHFFDWDORJWR
GHWHUPLQHIORZUDWH
ƒ)
/,48,'/,1(
36,
ƒ)
6$7
ƒ)
36,
36,
:$7(5,1
:$7(5287
&22/,1*&<&/($1$/<6,6
$,5+$1'/(56(&7,21&2035(66256(&7,21
36,
6$7
ƒ)
ƒ)
$,5
&2,/
68&7,21
ƒ)
&2035(6625
&22/,1*
(;3$16,21
9$/9(
+($7,1*
(;3$16,21
9$/9(
&2$;
',6&+$5*(
+:*
ƒ)
/RRNXSSUHVVXUHGURSLQ
,20RUVSHFFDWDORJWR
GHWHUPLQHIORZUDWH
ƒ)
/,48,'/,1(
36,
ƒ)
36,
:$7(5,1
ƒ)
6$7
36,
:$7(5287
&RROLQJH[SDQVLRQYDOYHPHWHUVLQWKHFRROLQJPRGHDQGE\SDVVHVLQWKHKHDWLQJPRGH
+HDWLQJH[SDQVLRQYDOYHPHWHUVLQWKHKHDWLQJPRGHDQGE\SDVVHVLQWKHFRROLQJPRGH
+HDWRI([WUDFWLRQ $EVRUEWLRQRU+HDWRI5HMHFWLRQ BBBBBBBBIORZUDWHJSP[BBBBBBBBWHPSGLIIGHJ)[BBBBBBBBBBIOXLGIDFWRU ‚ BBBBBBBBBBBBB
6XSHUKHDW
VXFWLRQWHPSHUDWXUHVXFWLRQVDWXUDWLRQWHPS
%WXKU
GHJ)
6XEFRROLQJ
GLVFKDUJHVDWXUDWLRQWHPS OLTXLGOLQHWHPS
GHJ)
‚8VHIRUZDWHUIRUDQWLIUHH]H
Note: Never connect refrigerant gauges during startup procedures. Conduct water-side analysis using P/T ports to determine water Åow
and temperature difference. If water-side analysis shows poor performance, refrigerant troubleshooting may be required. Connect refrigerant
gauges as a last resort.
51
52
Š
3OHDVHUHIHUWRWKH&DUULHU,QVWDOODWLRQ2SHUDWLRQDQG0DLQWHQDQFH0DQXDOIRURSHUDWLQJDQGPDLQWHQDQFHLQVWUXFWLRQV
5HY
3DUW1R&$
127(6RPHVWDWHVRU&DQDGLDQSURYLQFHVGRQRWDOORZOLPLWDWLRQVRQKRZORQJDQLPSOLHGZDUUDQW\ODVWVRUWKHOLPLWDWLRQRUH[FOXVLRQVRIFRQVHTXHQWLDORULQFLGHQWDOGDPDJHVVRWKHIRUHJRLQJH[FOXVLRQVDQGOLPLWDWLRQVPD\QRWDSSO\WR\RX7KLVZDUUDQW\JLYHV\RXVSHFLÀF
OHJDOULJKWVDQG\RXPD\DOVRKDYHRWKHUULJKWVZKLFKYDU\IURPVWDWHWRVWDWHDQGIURP&DQDGLDQSURYLQFHWR&DQDGLDQSURYLQFH
2%7$,1,1*:$55$17<3(5)250$1&(
1RUPDOO\WKHGHDOHURUVHUYLFHRUJDQL]DWLRQZKRLQVWDOOHGWKHSURGXFWVZLOOSURYLGHZDUUDQW\SHUIRUPDQFHIRUWKHRZQHU6KRXOGWKHLQVWDOOHUEHXQDYDLODEOHFRQWDFWDQ\&DUULHUUHFRJQL]HGGLVWULEXWRUGHDOHURUVHUYLFHRUJDQL]DWLRQ,IDVVLVWDQFHLVUHTXLUHGLQREWDLQLQJZDUUDQW\
SHUIRUPDQFHZULWHRUFDOO
&XVWRPHU6HUYLFH‡6:WK6WUHHW‡2NODKRPD&LW\2NODKRPD‡
/,0,7$7,212)/,$%,/,7<
&DUULHUVKDOOKDYHQROLDELOLW\IRUDQ\GDPDJHVLI&DUULHU·VSHUIRUPDQFHLVGHOD\HGIRUDQ\UHDVRQRULVSUHYHQWHGWRDQ\H[WHQWE\DQ\HYHQWVXFKDVEXWQRWOLPLWHGWRDQ\ZDUFLYLOXQUHVWJRYHUQPHQWUHVWULFWLRQVRUUHVWUDLQWVVWULNHVRUZRUNVWRSSDJHVÀUHÁRRGDFFLGHQW
VKRUWDJHVRIWUDQVSRUWDWLRQIXHOPDWHULDORUODERUDFWVRI*RGRUDQ\RWKHUUHDVRQEH\RQGWKHVROHFRQWURORI&DUULHU&$55,(5(;35(66/<',6&/$,06$1'(;&/8'(6$1</,$%,/,7<)25&216(48(17,$/25,1&,'(17$/'$0$*(,1&2175$&7)25
%5($&+2)$1<(;35(6625,03/,(':$55$17<25,17257:+(7+(5)25&$55,(5·61(*/,*(1&(25$6675,&7/,$%,/,7<
/,0,7$7,212)5(0(',(6
,QWKHHYHQWRIDEUHDFKRIWKH/LPLWHG([SUHVV:DUUDQW\&DUULHUZLOORQO\EHREOLJDWHGDW&DUULHU·VRSWLRQWRUHSDLUWKHIDLOHGSDUWRUXQLWRUWRIXUQLVKDQHZRUUHEXLOWSDUWRUXQLWLQH[FKDQJHIRUWKHSDUWRUXQLWZKLFKKDVIDLOHG,IDIWHUZULWWHQQRWLFHWR&DUULHU·VIDFWRU\LQ
2NODKRPD&LW\2NODKRPDRIHDFKGHIHFWPDOIXQFWLRQRURWKHUIDLOXUHDQGDUHDVRQDEOHQXPEHURIDWWHPSWVE\&DUULHUWRFRUUHFWWKHGHIHFWPDOIXQFWLRQRURWKHUIDLOXUHDQGWKHUHPHG\IDLOVRILWVHVVHQWLDOSXUSRVH&DUULHUVKDOOUHIXQGWKHSXUFKDVHSULFHSDLGWR&DUULHULQ
H[FKDQJHIRUWKHUHWXUQRIWKHVROGJRRGV6DLGUHIXQGVKDOOEHWKHPD[LPXPOLDELOLW\RI&DUULHU7+,65(0('<,67+(62/($1'(;&/86,9(5(0('<2)7+(%8<(525385&+$6(5$*$,167&$55,(5)25%5($&+2)&2175$&7)257+(
%5($&+2)$1<:$55$17<25)25&$55,(5·61(*/,*(1&(25,1675,&7/,$%,/,7<
/LPLWDWLRQ7KLV/LPLWHG([SUHVV:DUUDQW\LVJLYHQLQOLHXRIDOORWKHUZDUUDQWLHV,IQRWZLWKVWDQGLQJWKHGLVFODLPHUVFRQWDLQHGKHUHLQLWLVGHWHUPLQHGWKDWRWKHUZDUUDQWLHVH[LVWDQ\VXFKH[SUHVVZDUUDQW\LQFOXGLQJZLWKRXWOLPLWDWLRQDQ\H[SUHVVZDUUDQWLHVRUDQ\LPSOLHG
ZDUUDQWLHVRIÀWQHVVIRUSDUWLFXODUSXUSRVHDQGPHUFKDQWDELOLW\VKDOOEHOLPLWHGWRWKHGXUDWLRQRIWKH/LPLWHG([SUHVV:DUUDQW\
7KLV/LPLWHG([SUHVV:DUUDQW\DSSOLHVWR&DUULHUUHVLGHQWLDOJHRWKHUPDOSURGXFWVRUGHUHGIURP&DUULHURQRUDIWHU-XO\7KLVZRXOGJHQHUDOO\LQFOXGH&DUULHU*HRWKHUPDO8QLWVZLWKVHULDOQXPEHUVEHJLQQLQJZLWK´9µDQGODWHUDQGLVQRWUHWURDFWLYHWRDQ\SURGXFWV
RUGHUHGIURP&DUULHUSULRUWR-XO\WKLVZRXOGJHQHUDOO\LQFOXGH&DUULHU*HRWKHUPDO8QLWVZLWKVHULDOQXPEHUVEHJLQQLQJZLWK´9µDQGHDUOLHU,I\RXDUHXQVXUHLIWKLV/LPLWHG([SUHVV:DUUDQW\DSSOLHVWRWKHSURGXFW\RXKDYHSXUFKDVHGFRQWDFW&DUULHUDWWKHSKRQH
QXPEHURUDGGUHVVEHORZ
7KLV/LPLWHG([SUHVV:DUUDQW\SURYLGHVWKHOLPLWHGODERUDOORZDQFHFRYHUDJHVHWIRUWKDERYH2WKHUZLVH&DUULHULVQRWUHVSRQVLEOHIRU7KHFRVWVRIDQ\ÁXLGVUHIULJHUDQWRUV\VWHPFRPSRQHQWVVXSSOLHGE\RWKHUVRUDVVRFLDWHGODERUWRUHSDLURUUHSODFHWKHVDPHZKLFKLV
LQFXUUHGDVDUHVXOWRIDGHIHFWLYHSDUWFRYHUHGE\&DUULHU·V/LPLWHG([SUHVV:DUUDQW\7KHFRVWVRIODERUUHIULJHUDQWPDWHULDOVRUVHUYLFHLQFXUUHGLQGLDJQRVLVDQGUHPRYDORIWKHGHIHFWLYHSDUWRULQREWDLQLQJDQGUHSODFLQJWKHQHZRUUHSDLUHGSDUW7UDQVSRUWDWLRQFRVWVRI
WKHGHIHFWLYHSDUWIURPWKHLQVWDOODWLRQVLWHWR&DUULHURURIWKHUHWXUQRIWKDWSDUWLIQRWFRYHUHGE\&DUULHU·V/LPLWHG([SUHVV:DUUDQW\RU7KHFRVWVRIQRUPDOPDLQWHQDQFH
7KLVZDUUDQW\GRHVQRWFRYHUDQGGRHVQRWDSSO\WR$LUÀOWHUVIXVHVUHIULJHUDQWÁXLGVRLO3URGXFWVUHORFDWHGDIWHULQLWLDOLQVWDOODWLRQ$Q\SRUWLRQRUFRPSRQHQWRIDQ\V\VWHPWKDWLVQRWVXSSOLHGE\&DUULHUUHJDUGOHVVRIWKHFDXVHRIWKHIDLOXUHRIVXFKSRUWLRQ
RUFRPSRQHQW3URGXFWVRQZKLFKWKHXQLWLGHQWLÀFDWLRQWDJVRUODEHOVKDYHEHHQUHPRYHGRUGHIDFHG3URGXFWVRQZKLFKSD\PHQWWR&DUULHURUWRWKHRZQHU·VVHOOHURULQVWDOOLQJFRQWUDFWRULVLQGHIDXOW3URGXFWVVXEMHFWHGWRLPSURSHURULQDGHTXDWHLQVWDOODWLRQ
PDLQWHQDQFHUHSDLUZLULQJRUYROWDJHFRQGLWLRQV3URGXFWVVXEMHFWHGWRDFFLGHQWPLVXVHQHJOLJHQFHDEXVHÀUHÁRRGOLJKWQLQJXQDXWKRUL]HGDOWHUDWLRQPLVDSSOLFDWLRQFRQWDPLQDWHGRUFRUURVLYHDLURUOLTXLGVXSSO\RSHUDWLRQDWDEQRUPDODLURUOLTXLGWHPSHUDWXUHVRUÁRZ
UDWHVRURSHQLQJRIWKHUHIULJHUDQWFLUFXLWE\XQTXDOLÀHGSHUVRQQHO0ROGIXQJXVRUEDFWHULDGDPDJHV&RUURVLRQRUDEUDVLRQRIWKHSURGXFW3URGXFWVVXSSOLHGE\RWKHUV3URGXFWVZKLFKKDYHEHHQRSHUDWHGLQDPDQQHUFRQWUDU\WR&DUULHU·VSULQWHGLQVWUXFWLRQV
3URGXFWVZKLFKKDYHLQVXIÀFLHQWSHUIRUPDQFHDVDUHVXOWRILPSURSHUV\VWHPGHVLJQRULPSURSHUDSSOLFDWLRQLQVWDOODWLRQRUXVHRI&DUULHU·VSURGXFWVRU(OHFWULFLW\RUIXHOFRVWVRUDQ\LQFUHDVHVRUXQUHDOL]HGVDYLQJVLQVDPHIRUDQ\UHDVRQZKDWVRHYHU
7KLV/LPLWHG([SUHVV:DUUDQW\VKDOOFRYHUWKHODERULQFXUUHGE\&DUULHUDXWKRUL]HGVHUYLFHSHUVRQQHOLQFRQQHFWLRQZLWKWKHLQVWDOODWLRQRIDQHZRUUHSDLUHGZDUUDQW\SDUWWKDWLVFRYHUHGE\WKLV/LPLWHG([SUHVV:DUUDQW\RQO\WRWKHH[WHQWVSHFLÀFDOO\VHWIRUWKLQWKHWKHQH[LVWLQJ
ODERUDOORZDQFHVFKHGXOHSURYLGHGE\&DUULHU·V:DUUDQW\'HSDUWPHQWDQGRQO\DVIROORZV&DUULHU*HRWKHUPDO8QLWVIRUWZR\HDUVIURPWKH:DUUDQW\,QFHSWLRQ'DWH$X[LOLDU\HOHFWULFKHDWHUVDQGJHRWKHUPDOSXPSLQJPRGXOHVEXLOWRUVROGE\&DUULHUZKHQLQVWDOOHG
ZLWK&DUULHU*HRWKHUPDO8QLWVIRUWZR\HDUVIURPWKH:DUUDQW\,QFHSWLRQ'DWHDQG6HDOHGUHIULJHUDQWFLUFXLWFRPSRQHQWVRI&DUULHU*HRWKHUPDO8QLWVZKLFKFRPSRQHQWVRQO\LQFOXGHWKHFRPSUHVVRUUHIULJHUDQWWRDLUZDWHUKHDWH[FKDQJHUVUHYHUVLQJYDOYHERG\DQG
UHIULJHUDQWPHWHULQJGHYLFHIRUÀYH\HDUVIURPWKH:DUUDQW\,QFHSWLRQ'DWH$FWXDO/DERUFRVWVDUHQRWFRYHUHGE\WKLV/LPLWHG([SUHVV:DUUDQW\WRWKHH[WHQWWKH\H[FHHGWKHDPRXQWDOORZHGXQGHUVDLGDOORZDQFHVFKHGXOHWKH\DUHQRWVSHFLÀFDOO\SURYLGHGIRULQVDLG
DOORZDQFHVFKHGXOHWKH\DUHQRWWKHUHVXOWRIZRUNSHUIRUPHGE\&DUULHUDXWKRUL]HGVHUYLFHSHUVRQQHOWKH\DUHLQFXUUHGLQFRQQHFWLRQZLWKDSDUWQRWFRYHUHGE\WKLV/LPLWHG([SUHVV:DUUDQW\RUWKH\DUHLQFXUUHGPRUHWKDQWKHWLPHSHULRGVVHWIRUWKLQWKLVSDUDJUDSKDIWHUWKH
:DUUDQW\,QFHSWLRQ'DWH
7RPDNHDFODLPXQGHUWKLVZDUUDQW\SDUWVPXVWEHUHWXUQHGWR&DUULHULQ2NODKRPD&LW\2NODKRPDIUHLJKWSUHSDLGQRODWHUWKDQQLQHW\GD\VDIWHUWKHGDWHRIWKHIDLOXUHRIWKHSDUWLI&DUULHUGHWHUPLQHVWKHSDUWWREHGHIHFWLYHDQGZLWKLQ&DUULHU·V/LPLWHG([SUHVV:DUUDQW\
&DUULHUVKDOOZKHQVXFKSDUWKDVEHHQHLWKHUUHSODFHGRUUHSDLUHGUHWXUQVXFKWRDIDFWRU\UHFRJQL]HGGLVWULEXWRUGHDOHURUVHUYLFHRUJDQL]DWLRQ)2%&DUULHU2NODKRPD&LW\2NODKRPDIUHLJKWSUHSDLG7KHZDUUDQW\RQDQ\SDUWUHSDLUHGRUUHSODFHGXQGHUZDUUDQW\H[SLUHVDWWKH
HQGRIWKHRULJLQDOZDUUDQW\SHULRG
*5$172)/,0,7('(;35(66:$55$17<
&DUULHUZDUUDQWVLWVUHVLGHQWLDOJHRWKHUPDOSURGXFWVSXUFKDVHGDQGUHWDLQHGLQWKH8QLWHG6WDWHVRI$PHULFDDQG&DQDGDWREHIUHHIURPGHIHFWVLQPDWHULDODQGZRUNPDQVKLSXQGHUQRUPDOXVHDQGPDLQWHQDQFHDVIROORZV5HVLGHQWLDOJHRWKHUPDODLUFRQGLWLRQLQJKHDWLQJDQG
RUKHDWSXPSVZLWKPRGHOQXPEHUVEHJLQQLQJZLWK<WKDWDUHEXLOWRUVROGE\&DUULHU´&DUULHU*HRWKHUPDO8QLWVµIRUWHQ\HDUVIURPWKH:DUUDQW\,QFHSWLRQ'DWHDVGHÀQHGEHORZ$X[LOLDU\HOHFWULFKHDWHUVDQGJHRWKHUPDOSXPSLQJPRGXOHVEXLOWRUVROGE\&DUULHU
ZKHQLQVWDOOHGZLWK&DUULHU*HRWKHUPDO8QLWVIRUWHQ\HDUVIURPWKH:DUUDQW\,QFHSWLRQ'DWHDVGHÀQHGEHORZ6HDOHGUHIULJHUDQWFLUFXLWFRPSRQHQWVRI&DUULHU*HRWKHUPDO8QLWVZKLFKFRPSRQHQWVRQO\LQFOXGHWKHFRPSUHVVRUUHIULJHUDQWWRDLUZDWHUKHDWH[FKDQJHUV
UHYHUVLQJYDOYHERG\DQGUHIULJHUDQWPHWHULQJGHYLFHIRUWHQ\HDUVIURPWKH:DUUDQW\,QFHSWLRQ'DWHDVGHÀQHGEHORZDQG2WKHUDFFHVVRULHVDQGSDUWVEXLOWRUVROGE\&DUULHUZKHQLQVWDOOHGZLWK&DUULHU*HRWKHUPDO8QLWVIRURQH\HDUIURPWKHGDWHRIVKLSPHQW
IURP&DUULHU7KH´:DUUDQW\,QFHSWLRQ'DWHµVKDOOEHWKHGDWHRIRULJLQDOXQLWLQVWDOODWLRQRUVL[PRQWKVIURPGDWHRIXQLWVKLSPHQWIURP&DUULHUZKLFKHYHUFRPHVÀUVW
,WLVH[SUHVVO\XQGHUVWRRGWKDWXQOHVVDVWDWHPHQWLVVSHFLÀFDOO\LGHQWLÀHGDVDZDUUDQW\VWDWHPHQWVPDGHE\&DUULHU&RUSRUDWLRQD'HODZDUHFRUSRUDWLRQ´&DUULHUµRULWVUHSUHVHQWDWLYHVUHODWLQJWR&DUULHU·VSURGXFWVZKHWKHURUDOZULWWHQRUFRQWDLQHGLQDQ\VDOHVOLWHUDWXUH
FDWDORJRUDJUHHPHQWDUHQRWH[SUHVVZDUUDQWLHVDQGGRQRWIRUPDSDUWRIWKHEDVLVRIWKHEDUJDLQEXWDUHPHUHO\&DUULHU·VRSLQLRQRUFRPPHQGDWLRQRI&DUULHU·VSURGXFWV(;&(37$663(&,),&$//<6(7)257++(5(,17+(5(,612(;35(66:$55$17<
$672$1<2)&$55,(5·6352'8&76&$55,(50$.(612:$55$17<$*$,167/$7(17'()(&76&$55,(50$.(612:$55$17<2)0(5&+$17$%,/,7<2)7+(*22'6252)7+(),71(662)7+(*22'6)25$1<
3$57,&8/$5385326(
&$55,(5&25325$7,21
/,0,7('(;35(66:$55$17</,0,7$7,212)5(0(',(6$1'/,$%,/,7<)255(6,'(17,$/
*(27+(50$/352'8&76:,7+/$%25$//2:$1&(
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Warranty
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Notes
53
Residential Split Units - 60Hz Puron®
R e v. : 6 D e c . , 2 0 1 1
Revision History
Date
Page #
Description
6 Dec. 11
36
ATP32U03/4 Wiring Figure Added
31 Jan, 11
18
Refrigerant Charge Information Updated
13 Jan, 11
11
Circulator Check Valve Removed
Wiring
Wire Diagram revision: water-side high pressure switches
Diagram
added
Pages
15 July, 10
Various
Compressor isolation upgrade from springs to grommets
1 July, 10
Various
Warranty, Nomenclature, Unit Photos Updated
1 July, 10
7
Use of Splits with Carrier InÄnity or Bryant Evolution
Products
30 April, 10
26
HWG Piping Drawings Revised
16 Dec., 09
28
HWG Water Piping Size and Length Table Added
30 Oct., 09
46-47
15 Sept., 09
36
‘Safety Features - CXM/DXM Controls’ Section Updated
1 Sept., 09
All
First Published
Functional Troubleshooting Table Updated
R
AI
BR
I
HE
AT P U M P S
A
TO
NE
WATER
TO
IFIED TO ARI A
RT
S
C
CE
NG WITH
LYI
MP
O
IR
MANUFACT
UR
ER
21 July, 10
IS
O
ST
AND
3
ARD 1
ISO 9001:2000
Certified
-1
R
25
6
Quality: First & Always
7300 S.W. 44th Street
Oklahoma City, OK 73179
*97B0048N02*
Phone: 405-745-6000
Fax: 405-745-6058
97B0048N02
The Manufacturer works continually to improve its products. As a result, the design and speciÄcations of each product at the time for order may
be changed without notice and may not be as described herein. Please contact the Manufacturer’s Customer Service Department at 1-405745-6000 for speciÄc information on the current design and speciÄcations. Statements and other information contained herein are not express
warranties and do not form the basis of any bargain between the parties, but are merely Manufacturer’s opinion or commendation of its products.
The management system governing the manufacture of Manufacturer’s products is ISO 9001:2000 certiÄed.
© LSB, Inc. 2009
54
Rev.: 6 Dec., 2011
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising