CrimeStopper | SP-500 | Operating instructions | CrimeStopper SP-500 Operating instructions

CrimeStopper SP-500 Operating instructions
SP-500
2-Way LCD Paging Alarm & Remote Engine Starting System
OPERATING INSTRUCTIONS
INTRODUCTION
CONGRATULATIONS on your choice of the SP-500 by Crimestopper Security Products Inc. This booklet contains the
information necessary for operating your system. If any questions arise, contact your installation dealer or
Crimestopper Security Products Inc.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY: These features must be connected in order for the system to operate properly i.e. Power, Ground, LED,
etc.
-OPTIONAL: Optional features are connected only if desired or agreed upon by the installing dealer i.e. Horn Honk,
Dome light illumination, Door Locks, Trunk Pop, etc. These features may require additional parts and labor charges.
Consult with your installer about these features BEFORE installation!
CONTACT INFORMATION:
TECHNICAL SUPPORT (800)-998-6880
Monday - Friday 8:00am - 4:30pm Pacific
Website: www.crimestopper.com
CRIMESTOPPER
SECURITY PRODUCTS, INC.
1770 S. TAPO STREET
SIMI VALLEY, CA. 93063 REV
12.2008
This device complies with FCC Rules part 15. Operation is subject
to the following two conditions: 1) This device may not cause
interference, and (2) this device must accept any interference that
may be received, including interference that may cause undesired
operation. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modification to this
equipment. Such modification could void the user's authority to
operate the equipment.
TABLE OF CONTENTS
Operation Cautions & Warnings……..…………..……………………………………………………………………2
The Remote Controls……………….....…………..……………………………………………………………….…3-4
Setting the Clock………………...………………………….…………………………………………………..…...…..4
Quick Chart Button Functions...………………………….…………………………………………………..…...…..5
Operating Instructions - Alarm……………………………………………………….………..……………..……..6-9
Remote Engine Control………………………...……………………………………………….……………..….10-13
Anti-Carjack Protection...……………………………………….………….……..………………..………..………..14
LED and Remote Start Diagnostics………………..……………………………………………….………..….…15
Transceiver / Remote Control Programming……………………………………………………..…………….…16
2 Vehicle Operation……...………………………….……………………………….………….…………….….……17
TURBO Timer Mode…………….……………….…………………………………………………………..……..18-19
Battery Replacement……………….……………………..………….….…………………………………………….20
OPERATION CAUTIONS & WARNINGS
CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident
resulting from the use of this equipment. This system is designed to be professionally installed into a car or
vehicle in good running order. Items, such as parking brake, door switches, and all engine safety features,
must be in perfect working condition.
DAMAGE resulting from misuse or negligence is NOT covered under warranty and will be subject to
repair and / or replacement charges.
IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this
system and its safety features. B) Check for proper operation of these safety features prior to accepting
delivery of the vehicle from the installation facility. C) Check and maintain the condition of the vehicle and all
items relative to the proper operation of this system and its safety features.
DO NOT remote start the vehicle in a closed garage. Make sure that the vehicle is outdoors, a garage door
is open, or there is adequate exhaust ventilation. Failure to observe this rule could result in injury or death
from poisonous Carbon Monoxide fumes. This is especially important when using the Timed Self-Start feature
of the unit
2
THE REMOTE CONTROLS
2-WAY - PAGER / REMOTE TRANSCEIVER:
1-WAY - SIDEKICK REMOTE:
DISARM /
UNLOCK
AM
PM
12:00
START / AUX 2
ARM /
LOCK
2nd FUNCTION
VEH 1 / VEH 2
VEH 1 / VEH 2
CLOCK SET
START
TRUNK
TRUNK
ARM /
LOCK
2nd FUNCTION
DISARM /
UNLOCK
3
THE REMOTE CONTROLS
1-WAY - SIDEKICK REMOTE:
The 1-Way sidekick remote adds flexibility to your system. You can have the convenience of operating your
system without needing to carry the larger pager remote. The Sidekick remote has less range and offers all of
the same operation features except for page-back confirmation. The 1-Way Sidekick Remote uses two CR2016 Lithium 3 Volt Batteries.
2-WAY - PAGER / REMOTE TRANSCEIVER:
The 2-Way hand-held remote transceiver is used to send and receive information from the vehicle. The
Control Module transmits High Frequency FM signals from the vehicle to your pager over long distances. Your
range will vary depending on location, terrain, and local RF noise/interference. This system is not guaranteed
to page you if you are behind concrete walls, underground, in a large structure, or in an area with high levels
of electronic interference. Handle the pager/remote with care. The LCD display and/or the electronics may be
damaged if subjected to abuse. The AAA Cell 1.5V alkaline battery can easily be replaced by sliding open the
battery access door on the back of the remote. Battery life will vary depending on usage. The LCD screen
will display a low battery icon when the battery is low.
SETTING THE CLOCK (2-WAY- LCD REMOTE)
1.
2.
3.
4.
5.
6.
7.
Press VEH Button on the side of the remote control 5 times.
The remote will beep and the AM or PM display will begin flashing.
Press the Trunk Button to go to the next item – AM - PM - Hour- Minutes.
Press the Lock Button to increase time.
Press the Unlock Button to decrease time.
Press the Start Button to Disable or Enable Beep.
Press the VEH Button to Exit Setup or wait 7 seconds, the LCD light will turn off.
4
QUICK CHART BUTTON FUNCTIONS
Button
Functions
Button Options
Press and Hold 2
Seconds for Panic
Mode
2nd Function
Press and Hold for 2
seconds
Unlock Doors &
Disarm System
Press twice for
second door unlock
Selects between
Vehicle #1 and
Vehicle #2
Press and Hold for 2
seconds
Trunk Pop Aux # 1
Press and Release
for Trunk Pop Aux #1
Valet Service / Park
Sensor ON / Off
Valet Mode when
Disarmed. Sensor
On/Off when Armed
Start or Stop engine
Press for Remote
Start. Three options
available
Plus
Activates CarJack
with Ignition On
Press and Hold 2
Seconds for CarJack
Mode
Then
Activates Aux #2
Steady Momentary
Output
Plus
Activates Aux #2
Steady Momentary
Output
Then
Activates Aux #3
Momentary, Timed or
Latched Output
Plus
Activates Aux #3
Momentary, Timed
or Latched Output
Button
Button
Functions
Button Options
Lock Doors & Arm
System
Button
VEH
Then
No Function
No Function
Plus
Silent Arm / Disarm
No Arm / Disarm
Chrip from Siren or
Horn
Then
Activates Aux #4
Momentary, Timed or
Latched Output
Plus
Activates Aux #4
Momentary, Timed
or Latched Output
CLOCK SETUP:
Lock = Increase, Unlock = Decrease, Trunk = Next, Start = Beep with button press, VEH = Exit
5
OPERATING INSTRUCTIONS - ALARM
Arming / Locking:
Press the Lock Button on the remote control. The System will arm emit one siren chirp, one light flash, and the LED
will begin to flash. Power locks will lock (if equipped). Starter disable circuit will turn on. The 2-Way LCD Pager will
beep once while displaying a Locking symbol. After a short delay to allow the vehicle and electronics to settle, the
system will be completely armed.
Disarming: / Unlocking
Press the Unlock Button on the remote control. The System will disarm and confirm with two siren chirps, two light
flashes, and the LED will turn off. Power locks will unlock and Interior Dome light will turn on (if installed with these
optional features). The 2-Way LCD Pager will beep twice while displaying an Unlock symbol.
Alarm Triggers:
If there is an intrusion into the vehicle, a hard impact to the body or the ignition is turned on, the alarm will sound and
flash the lights for 1 minute. After 1 minute, the trigger cycle will automatically stop and alarm will remain armed to
continue protecting the vehicle. If a door is left open after an intrusion then the unit will cycle a maximum of 2 minutes
and continue to protect the other un-tampered or unopened zones.
LCD Remote Paging / Zone Violations:
When the system is triggered, the alarm sends a paging signal to the remote. If you are within range, you will receive
a paging signal that will light up the LCD Screen Red. The display will show an icon of what caused the violation. The
paging remote will also vibrate and beep to notify you the vehicle has been tampered with.
Disarming While Tripped (Triggered):
Disarming the System while it is triggering requires TWO presses of the Unlock Button. The first press Resets
the alarm cycle only (system still armed) while a second press will disarm/unlock the system.
Selective Silent Arming / Disarming:
To Arm or Disarm the system without siren chirps, press and release both the Unlock and Start Button at the
same time. The System will Arm or Disarm without siren chirps. Flashing lights and LED will be the only
indicators of Arm/Disarm status. The LCD will Display a musical note with an “Ø” when the system is armed or
disarmed without a chirp
6
OPERATING INSTRUCTIONS - ALARM
Prior intrusion Alert
This system will notify you if the alarm was triggered while you were away. Upon disarming, there will be four
additional siren chirps after the two normal disarm chirps. Check your vehicle for any signs of a break in or
tampering. Also, see LED Diagnostics (page 15) to determine the cause of the trigger.
Remote Panic Protection
To sound the alarm in an emergency situation or to draw attention to your vehicle, press and hold the Lock
button for at least 3 seconds until the siren / horn sounds. Press the Unlock button to reset panic mode. The
LCD display will flash most of the icons and emit 10 beeps when the Panic Mode is triggered.
Selective Shock Sensor Disable
To arm the alarm and bypass shock sensor protection, press the Lock Button as normal then press and
release the Lock & Unlock Button together within 2 seconds. You will hear 3 extra siren chirps indicating the
shock sensor bypass for this arming cycle only. This is feature useful when parking near railroad tracks,
airports, or areas with excessive loud machinery or noise to prevent the nuisance of unnecessary false
alarms.
Open Door Alert / Bypass
Upon arming, this system will warn you 60 seconds later if a door is left open. The LCD pager will vibrate and
beep (5X’s) along with displaying the open zone on your LCD screen. This zone will be bypassed until the
door is closed; otherwise, the alarm will continue to protect all other zones.
Pre-Warning Shock Protection
The Pre-Warning (Warn-A-Way) feature will activate when a low-level shock or vibration is detected by the
system’s shock sensor. The alarm will chirp the siren 5 times and flash the lights once to help deter any
further tampering with the vehicle. The pager / remote will beep and show a Hammer Icon.
Passive Arming Mode: (Programmable)
Passive (automatic) Arming occurs 30 seconds after the ignition is turned off and the last door is closed.
Upon closing the last door, the unit will flash the lights twice and LED will be flashing rapidly to confirm passive
countdown. If a door is reopened within the 30-second period, the countdown stops and begins again when
the door is closed. Passive arming provides failsafe protection in case you forget to arm the system.
7
OPERATING INSTRUCTIONS - ALARM
Passive Locking: (Programmable)
The system can be programmed to passively lock the doors when the system passively arms. The default
setting is OFF because passive locking increases the risk of locking the keys in the vehicle when the system
arms/locks passively, without you pressing the remote.
Trunk/Hatch Pop (Optional, Remote AUX. Output 1)
This feature is designed to interface with existing Factory power trunk or power hatch release systems and
may require additional parts and/or labor charges. To eliminate the possibility of accidentally opening the
trunk, there are (3) options for button press selection. This option will allow you to change whether the Remote
starter and Trunk release activate by a:
1. Double button ½ second presses.
2. Single ½ second press.
3. Press and Hold 2 seconds.
*Default = Single ½ second press*
Remote AUX. Output 2 (Optional, Requires special programming)
This system contains a 2nd Auxiliary output to activate other accessories or devices. To activate the 2nd
Auxiliary output, press the Unlock and Trunk button for more than 2 seconds. This momentary output will stay
active as long as the remote button is held down. There is no LCD / Pager confirmation for Aux. 2 output.
Remote AUX. Output 3 (Optional, Requires special programming)
This system contains a 3rd Auxiliary output to activate other accessories or devices. This output is
programmable for a momentary, timed or Latch output. There are 2 ways to control this output. To activate the
Third Auxiliary Output:
1. Press the 2nd Function button, than press the Trunk button on the transmitter.
2. Press the Lock and Key Button at the same time.
Remote AUX. Output 4 (Optional, Requires special programming)
This system contains a 4th Auxiliary output to activate other accessories or devices. This output is
programmable for a momentary, timed or Latch output. There are 2 ways to control this output. To activate the
Forth Auxiliary Output:
1. Press the 2nd Function button, than press the Lock button on the transmitter.
2. Press the Trunk and Start Button at the same time.
8
OPERATING INSTRUCTIONS - ALARM
Dome Light Illumination (Optional)
This feature will turn on the vehicle’s dome light upon disarming for 30 seconds or until the key is inserted and
turned on. This will provide illuminated entry to your vehicle in dimly lit areas for safety and security.
Emergency Override (Disarm)
If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to
disarm the system manually. Open the door with the key [alarm will sound], turn the ignition on, and press the
override/program button for about 5 seconds. The Alarm will disarm and allow you to use the vehicle until you
can repair/replace the remote. Valet mode also prevents Passive Arming.
Valet Mode (Enter manually or using the remote)
To disable Alarm and Remote Engine Starting for vehicle servicing the alarm system must be disarmed. To
Activate Valet Mode: Turn the ignition on and press the override/program button [about 5-6 seconds] until
you hear (3) siren chirps and the LED turns on solid. Repeat the process to exit VALET mode. To enter / exit
Valet via the remote, press and hold both the Lock and Unlock Button together for about 3 seconds until 3
chirps are heard. Repeat this step to exit via the remote transmitter. Lock / Unlock and AUX features will still
operate in VALET Mode however, Remote Start and Alarm functions are inhibited.
Valet Park Mode (Using the remote transmitter only)
Valet Park Mode allows you to turn over the vehicle to a Valet allowing access to drive/lock/unlock your
vehicle, but alarm will trigger if the trunk is opened. To Activate Valet Park: The alarm system must be
disarmed. Press and hold both the Lock and Unlock buttons together for about 3 seconds, 3 chirps will be
heard first when unit goes into regular Valet. Release, press and hold both buttons again, you will hear 2 more
chirps. The LED will always flash slowly when in Valet Park even when the Ignition is turned on (or driving
vehicle). Repeat step above to exit Valet Park Mode.
Note: Valet Park mode is only accessible when using the remote transmitter
9
REMO
REMOTE ENGINE CONTROLTE ENGINE CONTROL
Remote Start & Auxiliary Output – Button Press Selection (Option # 8):
To eliminate the possibility of accidentally opening the trunk or starting the vehicle, there are (3) options for
button press selection. This option will allow you to change whether the Remote starter and Trunk release
activate by a:
4. Double button ½ second presses.
5. Single ½ second press.
6. Press and Hold 2 seconds.
*Default = Single ½ second press*
REMOTE ENGINE STARTING - SUCCESSFUL START
1) Press remote start button on the remote transmitter. System will chirp 3 times for audible confirmation.
(Chirps can be programmed on or off-See installation manual.)
2) Parking lights flash once, then turn on solid, Ignition/Accessory circuits turn on.
3) After a few seconds, Starter Motor engages, Parking lights and Accessory circuits turn off while cranking.
4) Engine Starts and Runs. Parking Lights and Accessory turn back on, Doors Lock.
5) Engine will remain running for programmed run time until reset with Brake pedal. If needed, the engine can
be turned off with remote transmitter.
SOLID
FLASH 1X
AFTER
IGN
PRESS START
3
SEC.
THEN
SOLID
STARTER
REMOTE ENGINE STARTING – LCD PAGER-REMOTE:
When requesting a remote start the LCD pager remote will confirm with an Ignition Icon along with 3 beeps.
Once the vehicle has successfully started the remote will confirm back with 1 vibration, a moving vehicle Icon,
and 6 beeps.
10
REMOTE ENGINE CONTROL
UNSUCCESSFUL REMOTE START
In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then
attempts to restart the engine a 2nd and 3rd time. For hard starting engines, the unit will allow a starter crank
time of up to13 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to
13 seconds to help prevent damage to the starter from over cranking.
1) If engine starts on 2nd or 3rd attempt, see steps 4 & 5 (on last page) under "Successful Start".
2) If Third attempt fails to start engine, the system will turn off and doors will remain locked. NO FURTHER
ATTEMPTS WILL BE MADE AUTOMATICALLY UNLESS YOU PRESS THE REMOTE START BUTTON
AGAIN.
TURNING OFF YOUR REMOTE STARTED ENGINE (VIA REMOTE CONTROL):
1) Engine is running in Remote Start (Parking lights ON).
2) Press Remote Start button on remote transmitter.
3) Engine & parking lights turn OFF, Doors remain locked or will re-lock if applicable.
PRESS START
ENGINE & LIGHTS OFF
ENTERING YOUR REMOTE STARTED VEHICLE:
1) With engine running, Remote Unlock/Disarm system (If armed) or open door with key.
2) Enter vehicle and be careful not to step on brake pedal! (Remote Start Reset)
3) Turn Ignition to ON/RUN position, then press brake pedal to reset the Remote Starter & Shift out of park.
4) Remote starter will reset instantly when the brake is pressed. Parking lights will turn off and the ignition key
is now controlling your vehicle.
11
REMOTE ENGINE CONTROL
IDLE DOWN MODE (TAKE-OVER OPERATION)
This mode allows the unit to take over operation of your idling, parked vehicle while the ignition key is
removed and you exit the vehicle. The vehicle is put into a remote running condition before you exit and it will
remain running for the programmed run time, until you return, or until the remote start button is pressed.
Example:
You pull up to a convenience store for a quick stop, "Idle Down" mode keeps engine running when you
exit the vehicle, (with keys in hand) remote lock/arm alarm. When you return, unlock/disarm alarm, turn
ignition ON and drive away. This mode can also be used on Turbo vehicles that need idle for cool-down.
IDLE DOWN MODE - EXITING THE VEHICLE:
1) With engine running, press Remote Start button on remote transmitter. Siren will chirp 3 times for
confirmation.
2) Parking Lights will turn ON.
3) Doors will unlock, or if brake pedal is being depressed then doors will unlock when it is released.
4) Turn OFF Ignition and remove key. Engine should remain running.
5) Exit vehicle, then remote lock doors if desired.
6) Engine will remain running for programmed run time, until you return, or press the remote start button.
INFINITY RUN MODE
This mode allows the vehicle’s engine to remain running INDEFINITELY. This mode can be beneficial to law
enforcement vehicles or commercial vehicles that need to remain running unattended for long periods of time.
INFINITY RUN MODE – EXITING THE VEHICLE:
1) Follow steps for “IDLE DOWN MODE - EXITING THE VEHICLE” (above), except press the remote start
button a second time within 10 seconds at STEP #1.
2) Parking Lights will start flashing instead of coming on solid, and doors will unlock.
3) Turn Ignition switch OFF, remove key and exit the vehicle. Engine should remain running.
4) The vehicle’s parking lights will flash for the programmed run time of 12, 24, or 36, or 48 minutes and then
switch to solid while motor runs indefinitely or until fuel supply runs out.
12
REMOTE ENGINE CONTROL
TIMED SELF START MODE
This mode allows the vehicle to be programmed to self-start every 4 hours and run for the programmed run
time. This can be helpful during extremely cold conditions where engine or fluid freeze-up is a concern. !!THE
VEHICLE MUST BE OUTDOORS OR IN A WELL VENILATED AREA!!
TIMED SELF-START MODE – EXITING THE VEHICLE:
1) Have engine running with the Key, then press the Start button on the transmitter.
2) Within 10 seconds press the valet/program button once.
3) Parking Lights will turn OFF for about 5 seconds, and doors will unlock.
4) Turn Ignition switch OFF, remove key and exit the vehicle. Engine should remain running.
5) Press the remote start button again to turn off the engine. The parking lights will flash 4 TIMES as a
confirmation that the unit is in Timed Self-Start Mode.
6) The Vehicle will Start by itself every 4 hours, or until driven with key or started via remote control.
SOLID
START
WITHIN 10 SEC.
PRESS 1X
LIGHTS OFF 5 SEC.
UNLOCK
FLASH 4X
IGN
START
OFF
LOCK
RESETTING TIMED SELF START MODE
To reset the timed self-start mode, start vehicle using the ignition key or the remote control.
13
ANTI CARJACK PROTECTION
REMOTE OPERATED CARJACK PROTECTION
This feature provides Active Carjack protection through the remote control. When the Ignition is on (vehicle is
running), press and hold the #1 LOCK Button and #3 TRUNK Button for 2 seconds. The parking lights will
flash 2 times and the LED will begin to flash rapidly to confirm the beginning of a Carjack countdown. 30
Seconds later, the unit will begin a Carjack Cycle consisting of 20 seconds of pre-warning chirps turning into a
full system activation with siren / flashing light pulses for up to 5 min. If the Ignition is turned off during a
Carjack trigger the siren and lights stop but Carjack protection is still active. The Siren and Lights will resume
if the Carjacker tries to turn the Ignition back ON. TO RESET: Press Button #2 (UNLOCK) on the remote and
the siren will chirp once, or turn the key on and press and hold the override button for at least 5 seconds.
SWITCH-CONTROLLED & FULL TIME CARJACK (PINK WIRE CONFIGURATION)
This feature can provide Passive or Manual control Carjack protection depending on the configuration of the
Pink Carjack wire of the alarm system. The system must be programmed for the Pink wire to be used as a
Carjack trigger with programming option #20. Once programmed for the Pink wire for use as a Carjack trigger,
it can be configured in different ways to provide different levels of protection. It can be connected to a hidden
+12V toggle/momentary switch or to +12V Ignition Power. Read following sections for further descriptions.
HIDDEN SWITCH-CONTROLLED CARJACK:
This configuration will enable the vehicle owner to activate a Carjack countdown by pressing a hidden pushbutton (not included with kit) during a Carjack situation. A Carjack countdown will begin under the following
conditions: Ignition is ON (vehicle is running), the push-button is pressed, and the door opens/closes. Upon
these 3 events, in that order, the alarm will start a Carjack countdown. After a delay of one minute, the system
will begin chirping for 20 seconds then trigger into a full cycle for up to 5 minutes. To reset this Carjack mode,
Ignition must be ON then press and hold the override/valet button for 5 seconds (until LED goes out.)
FULL-TIME [Permanent] CARJACK:
We recommend that this configuration only be used if a serious threat of Carjack exists during everyday
situations. When the Ignition is on (vehicle is running), anytime a door is opened, the Carjack countdown
sequence will be initiated. There will be 2 light flashes and the LED will change from solid to quick pulsing as
confirmation of a countdown sequence. To reset FULL TIME Carjack, the Ignition has to be ON, then press
and hold the override/program button 5 seconds until LED stops pulsing. The LED will be on SOLID when in
this mode anytime the Ignition is ON (or while driving) as a reminder that Carjack is waiting for a door to open.
14
LED DIAGNOSTICS
The SP-500 system includes disarm diagnostics, through the BLUE LED light, that will help in determining
what caused the last trigger of the alarm system. This is a valuable tool in determining how the vehicle was
tampered with or if there is a false alarm problem in which case you can make the necessary adjustments to
correct the problem. When the system is disarmed with the remote you will hear the normal 2 chirps, then 4
quick chirps that indicate the alarm was triggered while you were away. Check the LED light for a sequence
of flashes:
Shock Sensor = 1 Flash
Door = 2 Flashes
Hood/Trunk = 3 Flashes
Ignition = 4 Flashes
Diagnostics will reset when the Ignition is turned on or when the system is re-armed.
REMOTE START DIAGNOSTICS
If the system flashes the parking lights one to three times and doesn’t attempt remote, it means the following:
1 Parking Light Flash = Problem with Brake Switch.
2 Parking Light Flashes = Problem with Hood Switch.
3 Parking Light Flashes = Valet Service Mode.
7 Parking Light Flashes = Manual Transmission Mode Error.
15
TRANSCEIVER / REMOTE CONTROL PROGRAMMING
Note: All transmitter codes must be learned at time of programming!! The SP-500 learns up to 4
different transmitter codes.
1. Turn key to the ON position. (Pink wire must be connected.)
2. Press Programming button 4 times, then after a few seconds the unit flashes the parking lights 4 times.
3. Press button #1 of the transmitter to be coded. You should get 2 light flashes indicating the unit is waiting
for a 2nd code, then press button #1 of a second transmitter, the unit will flash 3 times indicating its waiting
for the 3rd code and so on. If all 4 codes are learned, the unit will automatically exit code learning mode,
otherwise turn key off. See diagram below.
IGN
OFF
WAIT FOR
4 FLASHES
PRESS 4X's
IGN
OFF
FLASH 2, 3, or 4 X's
COMPLETE
PRESS LOCK
16
2 VEHICLE OPERATION
2 VEHICLE CONTROL
Your remotes have the ability to control a second vehicle with a Crimestopper system installed.
To set up the 2-Vehicle operation you must first program your remotes to Vehicle #2. Follow the “Transmitter
Programming” steps (Pg. 16) at the second vehicle and learn YOUR remote, along with vehicle #2’s existing
remotes.
2-VEHCLE NOTES:
(1) You do not have to switch between Vehicle “1” and “2” to get pages from each vehicle. Your remote pager
will receive pages from both cars regardless of which vehicle the pager is set to. The “1” or “2” icon will
always display with each page indicate which vehicle the page originated from.
(2) When, all remote/pagers and sidekick remotes for that vehicle must be learned at the time of programming.
When you program your remote at the second vehicle, that vehicle’s original remote must also be
programmed. Your remote should be set in Vehicle “2” and the vehicle’s original remote should be set in
Vehicle “1”.
VEHICLE 1 or 2
VEHICLE 1 = RED LED
VEHICLE 2 = BLUE LED
FUNCTION 1 or 2
2-1
TRANSMIT ICON
VEH 1 / VEH 2
CLOCK SET
Push 2 Seconds
to change from
Vehicle 1 to 2.
VEH 1 / VEH 2
Push 2 Seconds
to change from
Vehicle 1 to 2.
17
OPTIONAL TURBO TIMER MODE
The optional Turbo Timer mode allows the CoolStart system to keep a Turbo or Turbo Diesel vehicle running
for 1 to 5 minutes [selectively] after you remove the key and exit the vehicle. This is handy for turbo cooldown without the need for expensive turbo timers. This mode requires the use of an extra part called a
momentary switch/button that is not included with the kit. There are (3) modes of operation for the Turbo
Timer Mode
1. Brake Pedal Set Mode. With the engine running by key, press Remote Start Button with brake pedal
depressed. As you release the brake pedal, the Parking Lights and Status LED will blink the number of
minutes for the Turbo Timer setting. The doors unlock after confirmation. The run time can be changed
by using the push button switch attached to the green start activation wire (see Always Set Mode).
2. Always Set Mode (default). The Turbo Timer Run Time must always be set. With brake pedal
depressed and engine running by key, Press the “Turbo Timer” button 1 to 5 times for each minute of
run time you desire. (1 press = 1 min.) As you release the brake pedal, your system will confirm by
flashing the lights the same number of times the button was pressed. The doors unlock after
confirmation. Turn Ignition switch OFF, remove key and exit the vehicle.
3. Idle Down Mode. This replaces the normal Idle Down Mode. Can’t use Infinity Run or Manual
Transmission Mode with this option. With the engine running by key, press the Remote Start
Button. The Parking Lights and Status LED will blink the number of minutes for the Turbo Timer setting.
The doors unlock after confirmation. The run time can be changed by using the push button switch
attached to the green start activation wire (see Always Set Mode).
Note: Mode 1 and 3, the run timer (1 to 5 min.) is set one time. The system always remembers the Turbo
Timer setting even with battery disconnection.
18
SETTING THE TURBO TIMER RUN TIME
RUNNING
LIGHTS
FLASH 1-5X
PRESS TURBO
TIMER BUTTON
1-5 TIMES
PRESS
AND HOLD
BRAKE
RELEASE
BRAKE
REMOVE KEY
EXIT VEH.
REMAIN
RUNNING
1-5 MIN.
CAUTION!! IF YOU PRESS THE TURBO TIMER BUTTON WHEN ENGINE IS NOT RUNNING IT WILL
TRIGGER A REMOTE START! MAKE A NOTE OF THIS IF YOU HAVE CHILDREN. CONSIDER THIS
WHEN CHOOSING A LOCATION FOR YOUR TURBO TIMER BUTTON.
19
BATTERY REPLACEMENT
LOW BATTERY WARNING
The 2-Way LCD remote has a low battery warning system. When the battery
voltage is low, the LCD Pager Remote will show a low voltage icon. We
recommend replacing the battery for proper operation. To replace the battery:
Simply unlatch and slide open the battery door on the back of the remote.
Carefully insert a new 1½ Volt AAA using the outline on the bottom of the
battery compartment as a guide. Your remote will beep 3 times & vibrate if the
battery was inserted correctly. Otherwise, remove the battery and insert again.
LOW BATTERY
LOW BATTERY
To replace the battery on Sidekick:
The 1-Way Sidekick Remote uses Two CR-2016 Lithium 3 Volt Batteries. Simply
remove the two Phillips screws holding the back cover in place. Insert the new
batteries with the (+) end toward the circuit board.
Remove
2 Screws
Crimestopper Security Products Inc.
1770 So. Tapo Street
Simi Valley, CA 93063
(800) 998-6880
www.crimestopper.com
©2008 Crimestopper Security Products
ONLINE TECHNICAL SUPPORT
www.crimestopper.com
20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising