Epson | EMP-1815 | User`s guide | Epson EMP-1815 User`s guide

1
User’s Guide
Notations Used in This Guide
Attention
q
s
g
Procedure
[ (Name) ]
"(Menu Name)"
Indicates procedures which may result in damage or injury if sufficient care is not taken.
Indicates additional information and points which may be useful to know regarding a topic.
Indicates a page where detailed information regarding a topic can be found.
Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See
the "Glossary" section of the "Appendices". s p.88
Indicates operating methods and the order of operations.
The procedure indicated should be carried out in the order of the numbered steps.
Indicates the name of the buttons on the remote control or the control panel.
Example: [Esc] button
Indicates configuration menu items.
Example: "Image" - "Brightness"
Indicates that the explanation continues on the following page. Clicking this symbol will display the following page.
Indicates that the explanation is continued from the previous page. Clicking this symbol will display the previous page.
2
Contents
Projector Features......................................................................................5
EMP-1815/1810 Common Features .................................................................... 5
EMP-1815 Features ............................................................................................. 6
Part Names and Functions ........................................................................7
Front/Top.............................................................................................................. 7
Side (EMP-1815 Only) ......................................................................................... 8
Base ..................................................................................................................... 9
Rear ................................................................................................................... 10
Control Panel ..................................................................................................... 12
Remote Control .................................................................................................. 13
Useful Functions
Correcting Distortion in the Projected Image ........................................16
Automatically Correcting Distortion (Quick Setup) ............................................. 17
Aligning the Projected Image to the Screen (Quick Corner) .............................. 18
Changing the Projected Image................................................................20
Automatically Detect Incoming Signals and Change the Projected Image
(Source Search) ................................................................................................. 20
Changing Directly from the Remote Control ...................................................... 21
3
Configuration Menu
Using the Configuration Menu................................................................ 40
List of Functions ...................................................................................... 41
Image Menu....................................................................................................... 41
Signal Menu....................................................................................................... 42
Settings Menu.................................................................................................... 43
Extended Menu.................................................................................................. 44
Network Menu (EMP-1815 Only)....................................................................... 46
Info Menu (Display Only) ................................................................................... 57
Reset Menu ....................................................................................................... 58
Troubleshooting
Using the Help .......................................................................................... 60
Problem Solving....................................................................................... 61
Reading the Indicators....................................................................................... 61
When the Indicators Provide No Help................................................................ 64
Appendices
Functions for Enhancing Projection.......................................................22
Selecting the Projection Quality (Selecting Colour Mode) ................................. 22
Hiding the Image and Sound Temporarily (A/V Mute) ....................................... 23
Freezing the Image (Freeze).............................................................................. 24
Changing the Aspect Ratio (Resize) .................................................................. 25
Pointer Function (Pointer) .................................................................................. 26
Enlarging Part of the Image (E-Zoom) ............................................................... 27
Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse)..... 28
Remote Control of Two or More Projectors ...........................................30
Setting the Projector ID ...................................................................................... 30
Setting the Remote Control ID ........................................................................... 31
Adjusting Colour for Several Projectors (Multi-Screen Colour
Adjustment)...............................................................................................32
Summary of Adjustment Procedure ................................................................... 32
Image Correction Method................................................................................... 33
Security Functions ...................................................................................34
Managing Users (Password Protect) ................................................................. 34
Restricting Operation (Operation Lock).............................................................. 37
Anti-Theft Lock ................................................................................................... 38
Installation Methods ................................................................................ 72
Cleaning .................................................................................................... 73
Cleaning the Projector's Surface ....................................................................... 73
Cleaning the Lens.............................................................................................. 73
Cleaning the Air Filter and Air Intake Vent......................................................... 73
Replacing Consumables ......................................................................... 74
Replacing the Remote Control Batteries ........................................................... 74
Replacing the Lamp........................................................................................... 75
Replacing the Air Filter ...................................................................................... 78
Saving a User’s Logo............................................................................... 79
Screen Size and Distance........................................................................ 81
Connecting USB Devices (Digital Camera, Hard Disk Drive or Memory
Devices) (EMP-1815 Only) ....................................................................... 82
Connecting USB Devices .................................................................................. 82
Inserting and Ejecting CompactFlash Cards (EMP-1815 Only) ........... 83
How to Insert Cards ........................................................................................... 83
How to Remove Cards....................................................................................... 83
Connecting to External Equipment ........................................................ 85
Connecting to an External Monitor .................................................................... 85
Connecting to External Speakers ...................................................................... 85
Contents
Connecting a LAN Cable..........................................................................86
Optional Accessories and Consumables...............................................87
Glossary ....................................................................................................88
ESC/VP21 Commands..............................................................................90
Command List .................................................................................................... 90
Cable Layouts .................................................................................................... 90
PJLink (EMP-1815 Only) ..........................................................................91
List of Supported Monitor Displays........................................................92
Specifications ...........................................................................................93
Appearance ...............................................................................................97
Index ..........................................................................................................98
4
Projector Features
5
EMP-1815/1810 Common Features
The following introduces features common to the EMP-1815 and the
EMP-1810.
Enhanced security functions
f Password Protect to restrict and manage users
By setting a password you can restrict who can use the projector. s p.34
Ease of use
f Quick Setup
This feature corrects distortion in the projected image by a simple onetouch operation. Images can be corrected and matched to the size of the
screen to simplify preparations.
f The A/V mute slide makes it
easy to project and store
You can stop and resume projection
easily by opening and closing the A/V
mute slide which makes giving clear
presentations easier.
f Operation Lock restricts button operation on the control
panel
You can use this to prevent people changing projector settings without
permission at events, in schools, and so on. s p.37
f Equipped with various anti-theft devices
The projector is equipped with the following security devices. s p.38
• Security slot
• Security cable installation point
Easy to handle
f Direct power On/Off
In places where power is managed centrally, such as in a conference
room, the projector can be set to power on and off automatically when the
power source to which the projector is connected is switched on or off.
f A single foot design means you do not have to make any
difficult leveling adjustments
You can easily make height
adjustments with one hand.
s Quick Start Guide
f No cool down delay
You can disconnect the projector's power cable without having to wait for
the projector to cool down first.
f High powered, 1.6 times zoom lens
The 1.6 times zoom allows for a wide range of installation positions to
suit most room layouts, whether the projector is on a stand, a table, or
ceiling mounted.
6
Projector Features
EMP-1815 Features
The EMP-1815 can be connected to a computer by a wired or wireless
LAN connection. The situations in which this projector can be used
increase as shown below if you use the PC applications supplied.
Strengthened security level of wireless LAN
Security is stronger than previous models. You can feel secure using it as
part of the network. s EasyMP Operation Guide
Second and third screen projection (Multi-screen display)
Connect to a computer easily
f Computer and wireless connection
Use a wireless LAN to connect
easily to your computer in a 1:1
configuration. s Wireless LAN
Quick Connection Guide
You can also connect to the access
point. s EasyMP Operation Guide
f Connect using a USB cable
(USB display)
Simply by connecting a cable to
your computer you can project
images from the computer's screen.
s Wireless LAN Quick Connection
Guide
Powerful presentation support
f Presentations without a computer
You can record presentation data scenarios to media beforehand, and then
simply start playback to make the presentation without a computer.
s EasyMP Operation Guide
f Slide show projection only (Presentation mode)
This mode allows you to project only images of your PowerPoint slide
show. You can give stylish presentations without showing spectators
operations or other preparation material. s EasyMP Operation Guide
You can project each virtual display set on the computer by using two or
more projectors. You can use it to make file operations and arrangements
for the virtual displays while projecting only the virtual displays.
s EasyMP Operation Guide
Part Names and Functions
7
Front/Top
Name
D
A
B
Air exhaust vent
D
E
E
Speaker
F
I
H
Front adjustable
feet
Extend and adjust the position of the projected
image when the projector is placed on a
surface such as a desk. s Quick Start Guide
G
Foot adjust lever
Pull out the foot lever to extend and retract the
front foot. s Quick Start Guide
G
H
A/V mute slide
Slide shut when not using the projector to
protect the lens. By closing during projection
you can hide the image and the sound (A/V
Mute). s Quick Start Guide, p.22
I
Remote receiver
Receives signals from the remote control.
s Quick Start Guide
J
A/V mute slide
knob
Slide the knob to open and close the A/V mute
slide.
K
Focus ring
Adjusts the image focus. s Quick Start
Guide
L
Zoom ring
Adjusts the image size. s Quick Start Guide
F
Name
Function
A
Control panel
s p.12
B
USB access
indicator
(EMP-1815 Only)
Whether they are flashing or lit indicates the
access status of USB Type A.
When the indicator is off, this indicates that no
USB devices are inserted.
When the light is orange, this indicates that a
USB device is inserted.
When the light is red, this indicates that an
error has occurred.
C
Lamp cover
Attention
Do not place objects that may become warped
or otherwise affected by heat near the air
exhaust vent and do not put your face or
hands near the air exhaust vent while
projection is in progress.
L
K
J
C
Function
Open this cover when replacing the projector's
lamp. s p.75
8
Part Names and Functions
Side (EMP-1815 Only)
A
D
C
B
Name
Function
A
Wireless LAN unit Install this before using the projector. Connects
the projector to a computer by a wireless
connection. s Wireless LAN Quick
Connection Guide
B
Card slot
This slot is for inserting a CompactFlash card
when the PC Free function in EasyMP is used.
You can also write to the CompactFlash card
from a computer connected to the projector via
a network. s p.83
C
Card slot access
indicator
Indicates the access status of the
CompactFlash card. s p.84
D
Eject button
Press this button to eject the CompactFlash
card. s p.83
9
Part Names and Functions
Base
Name
E
D
A
B
C
C
Name
Function
A
Suspension
bracket fixing
points (3 points)
Attach the optional ceiling mount here when
suspending the projector from a ceiling.
s p.72, 87
B
Security cable
installation point
Pass a commercially available anti-theft wire
lock through here when you want to secure the
projector to a fixed object. s p.38
C
Rear foot
Turn to extend and retract to adjust the
horizontal tilt. s Quick Start Guide
D
Screw hole to fix This hole is for a screw to fix the wireless LAN
wireless LAN unit unit in place. s Wireless LAN Quick
Connection Guide
E
Air filter (Air
intake vent)
Function
This prevents dust and other foreign particles
from getting inside the projector when air is
drawn in. The projector displays a warning
message when it is time to clean or replace the
air filter. s p.73, 78
10
Part Names and Functions
Rear
Name
B C
Name
A
Audio-L/R input
port
These connect to the audio out port of
equipment that is connected to the S-Video or
Video input port. s Quick Start Guide
D
RS-232C port
When controlling the projector from a
computer, connect it to the computer with an
RS-232C cable. This port is for control use and
should not normally be used. s p.90
E
Remote receiver
Receives signals from the remote control.
s Quick Start Guide
F
Security slot (j)
The security slot is compatible with the
Microsaver Security System manufactured by
Kensington. s p.38
G
USB port (Type A) Connects the memory for compatible digital
(EMP-1815 only)
cameras and USBs, and projects image/movie
files and scenarios with the PC Free of
EasyMP. s p.82
H
LAN port
(EMP-1815 only)
I
USB port (Type B) Connects the projector to a computer by a
USB cable, and the image on the computer is
projected (EMP-1815 only). s Wireless LAN
Quick Connection Guide
Use this port also to connect with a computer
to use the wireless mouse function. s p.28
J
Computer1 input
port
J I HG
A
Monitor Out port
D E
F
Function
Outputs the image signal from the computer
connected to the Computer1 input port to an
external monitor. This is not available for
component video g signals or other signals
being input to any port other than the
Computer1 input port.
Audio Out port
Outputs the sound of the image currently being
projected to external speakers.
s p.85
B
Power inlet
Connects to the power cable. s Quick Start
Guide
C
S-Video input
port
For S-videog signals from video sources.
Video input port
For composite videog signals from video
sources.
Function
When a LAN cable is connected, you can
monitor and control the projector over a LAN.
s p.86
For video signals from a computer and
component videog signals from other video
sources.
Audio1 input port Connect to the audio out port of the computer
connected to the Computer1 input port.
11
Part Names and Functions
Name
Computer2 input
port
Function
For video signals from a computer and
component videog signals from other video
sources.
Audio2 input port Connect to the audio out port of the computer
connected to the Computer2 input port.
s Quick Start Guide
12
Part Names and Functions
Control Panel
A
J
I
B
Name
C
H
D
G
Name
Function
D
[Enter] button
If pressed during projection of computer signal
images, it automatically adjusts the tracking,
synchronization, and position to project the
optimum image.
When a configuration menu or a help screen is
displayed, it accepts and enters the current
selection and moves to the next level. s p.40
E
[v] [w] buttons
Corrects keystone distortion.
If pressed when a configuration menu or a help
screen is displayed, these buttons select menu
items and setting values.
s Quick Start Guide, p.40
F
[Help] button
Displays and closes the help screen which
shows you how to deal with problems if they
occur. s p.60
G
[Esc] button
Stops the current function.
If pressed when a configuration menu is
displayed, it moves to the previous menu level.
s p.40
H
[<] [>] buttons
Corrects keystone distortion.
If pressed when a configuration menu or a help
screen is displayed, these buttons select menu
items and setting values. s Quick Start
Guide, p.40
I
[Menu] button
Displays and closes the configuration menu.
s p.40
J
Status indicators
The colour of the indicators and whether they
are flashing or lit indicates the status of the
projector. s p.61
F
E
Function
A
[Power] button
Turns the projector power on or off. s Quick
Start Guide
B
[Quick Setup]
button
Press this button to correct distortion in the
projected image so that it perfectly matches
the size of the screen. s p.17
C
[Source Search]
button
Changes to the next input source that is
connected to the projector and is sending an
image. s p.20
13
Part Names and Functions
Remote Control
Function
When the wireless mouse function or Network
presentation* is performed, you can change
the PowerPoint file page by pressing the page
up/page down buttons. s p.28, EasyMP
Operation Guide
* EMP-1815 only
A
Y
B
[Page] button
([) (])
B
X
W
C
[A/V Mute] button Turns the video and audio on or off. s p.23
V
D
[Pointer] button
Press to activate the on screen pointer.
s p.26
U
T
S
R
Q
P
O
N
E
[Color Mode]
button
Each time the button is pressed, the colour
mode changes. s p.22
F
[Comp2] button
Changes to an image from the Computer2
input port. s p.21
G
[Comp1] button
Changes to an image from the Computer1
input port. s p.21
H
[S-Video] button
Changes to an image from the S-Video input
port. s p.21
I
[Video] button
Changes to images from the Video input port.
s p.21
J
[EasyMP] button
Changes to the EasyMP image. This feature is
not provided on the EMP-1810. (EMP-1815
only)
K
Numeric buttons
Use these buttons when entering a password,
projector ID or remote control ID. s p.36
L
[Search] button
Changes to the next input source that is
connected to the projector and is sending an
image. s p.20
C
D
E
F
G
H
I
J
K
L
Name
A
Name
[E-Zoom]button
(z) (x)
M
Function
(z) Enlarges the image without changing the
projection size.
(x) Reduces parts of images that have been
enlarged using the [z] button.
s p.27
14
Part Names and Functions
Name
Function
M
[Volume] button
(a) (b)
(a) Decreases the volume.
(b) Increases the volume.
s Quick Start Guide
N
[Auto] button
If pressed during projection of computer signal
images, it automatically adjusts the tracking,
synchronization, and position to project the
optimum image. s p.41
O
[Help] button
Displays and closes the help screen which
shows you how to deal with problems if they
occur. s p.60
P
[ID] button
Press this button to check if the projector can
be operated by the remote control. Also, press
it to set the remote control ID. s p.30
Q
[Resize] button
The aspect ratiog changes each time the
button is pressed. s p.25
R
[Num] button
Use this button when entering a password or
screen ID. s p.36
S
[Freeze] button
Images are paused or unpaused. s p.24
T
[Esc] button
Stops the current function. If pressed when a
configuration menu is displayed, it moves to
the previous level. Acts as a mouse's right
button when using the wireless mouse
function. s p.40
U
[Enter] button
When a configuration menu or a help screen is
displayed, it accepts and enters the current
selection and moves to the next level. Acts as
a mouse's left button when using the wireless
mouse function. s p.40
Name
Function
V
[h] button
When a configuration menu or help screen is
displayed, it selects menu items and setting
values. When the wireless mouse function is
activated, tilting this button moves the pointer
in the direction it is tilted. s p.40
W
[Menu] button
Displays and closes the configuration menu.
s p.40
X
[Power] button
Turns the projector power on or off. s Quick
Start Guide
Y
Remote control
light-emitting
area
Outputs remote control signals. s Quick
Start Guide
Useful Functions
This chapter explains useful functions for giving presentations and so on, and the security functions.
Correcting Distortion in the Projected Image .. 16
Remote Control of Two or More Projectors......30
• Automatically Correcting Distortion (Quick Setup)......17
• Setting the Projector ID ................................................... 30
• Setting the Remote Control ID........................................ 31
Fitting projected image properly inside the screen ........................17
• Aligning the Projected Image to the Screen
(Quick Corner) ..................................................................18
Changing the Projected Image .......................... 20
• Automatically Detect Incoming Signals and Change the
Projected Image (Source Search) ....................................20
• Changing Directly from the Remote Control .................21
Functions for Enhancing Projection ................. 22
• Selecting the Projection Quality
(Selecting Colour Mode) ...................................................22
• Hiding the Image and Sound Temporarily (A/V Mute) 23
• Freezing the Image (Freeze).............................................24
• Changing the Aspect Ratio (Resize) ................................25
• Pointer Function (Pointer) ...............................................26
• Enlarging Part of the Image (E-Zoom) ...........................27
• Using the Remote Control to Operate the Mouse Pointer
(Wireless Mouse) ...............................................................28
Adjusting Colour for Several Projectors
(Multi-Screen Colour Adjustment).....................32
• Summary of Adjustment Procedure............................... 32
• Image Correction Method ............................................... 33
Security Functions..............................................34
• Managing Users (Password Protect)............................... 34
Type of Password Protect .............................................................. 34
Setting Password Protect................................................................ 35
Entering the Password.................................................................... 36
• Restricting Operation (Operation Lock)........................ 37
• Anti-Theft Lock ................................................................ 38
Installing the wire lock................................................................... 38
Correcting Distortion in the Projected Image
There are four ways to correct distortion in projected images as below.
Automatic correction
• Quick Setup
Press the [Quick Setup] button to fit on the screen at an aspect ratio
of 4:3.
• Auto V-Keystone
Tilt the projector vertically to automatically correct distortion in the
vertical direction.
q
• The default setting in the configuration menu is H/VKeystone.
• Select "Settings" - "Keystone" - "Quick Corner" to use
Quick Corner for correction.
• To change the setting from Quick Corner to H/V-Keystone,
press and hold the [Esc] button on the projector or the
remote control for about two seconds and display the
following screen where you can make the change.
Manual correction
• Quick Corner
This allows you to manually correct each of the four corners of the
projected image separately.
• H/V-Keystone
This allows you to manually correct distortion in the horizontal and
vertical directions independently.
The "Quick Setup", "Quick Corner", "Auto V-Keystone" and "H/VKeystone" functions project a test pattern onto the screen to correct
the projected image, so connection to a computer for preparing the
projector is not required.
Reset Quick Corner: Resets the Quick Corner settings.
Switch to H/V-Keystone: Switches the keystone correction method to
H/V-Keystone. s p.43
16
17
Correcting Distortion in the Projected Image
Automatically Correcting Distortion (Quick Setup)
Quick Setup automatically corrects distortion in the projected image, that
occurs when the projector is installed at a tilt to the image projection
surface, so that the image is projected at an aspect ratio of 4:3. In the case
of a screen having an aspect ratio of 4:3, the projected image is corrected
so that it fits perfectly in the screen.
Refer to Quick Start Guide for how to do the operation. Here is how to fit
the projected image within the screen.
f Fitting projected image properly inside the screen
When Quick Setup detects a "frame" (detecting 3 or more sides, or top
and bottom sides, or 2 adjacent sides) within the projection area, it
automatically corrects the image so that it fits within the "frame" at an
aspect ratio of 4:3. The "frame" means the borders of the screen,
whiteboard or blackboard.
*
When 3 or more sides
are detected
q
The status after correction by Quick Setup is stored in
memory even after the projector is turned off. When the
projector is installed at a fixed position for use, the
projected image does not need to be corrected once Quick
Setup has been performed.
When top and bottom sides, or 2
adjacent sides are detected
* When the projector is mounted from the ceiling, the image will be corrected
so that the bottom edge of the frame, such as the screen, fits inside the
projection area.
When no border
is detected
When the frame is
horizontally long
18
Correcting Distortion in the Projected Image
q
• Quick Setup can provide effective correction when the
borders of the projection surface stand out clearly, such as
a white screen with black borders. When protecting
images on a blackboard, for example, you should stick a
large-sized sheet of white paper on the blackboard.
• Quick Setup can be used to carry out correction within the
ranges given below. If the distortion is outside these
ranges, correction will not be carried out correctly.
Furthermore, if the image is distorted both vertically and
horizontally or if the zoom has been adjusted to "W", the
correction range will become narrower than the angles
given below.
- When correcting to within a border
Vertically: Approx. 45°Horizontally: Approx. 20°
- When projecting onto a surface without a border
Vertically: Approx. 45°Horizontally: Approx. 15°
Aligning the Projected Image to the Screen (Quick
Corner)
This function independently corrects each of the four corners of the
projected image to align the image with the screen.
Procedure
To operate this function on the projector's control panel, set "Setting
menu" - "Keystone" in the configuration menu to "QuickCorner".
A Press one of [w], [v], [<] and [>] on the projector.
The Quick Corner screen for selecting the four corners is
displayed.
the corner to be corrected, and press the
B Select
[Enter] button on the projector or remote control.
Correcting Distortion in the Projected Image
the position of the corner by the [w], [v],
C Correct
[<] and [>] buttons on the projector or the [h]
button on the remote control.
If the screen below is displayed during the correction, this indicates
that the correction amount limit has been reached.
exit the correction, press the [Esc] button on the
D Toprojector
or remote control.
19
Changing the Projected Image
20
You can change the projected image in the following two ways.
• Changing by Source Search
The projector automatically detects signals being input from
connected equipment, and the image being input from the equipment
is projected.
• Changing directly
You can use the remote control buttons to change to the target input
port.
Using the remote control
When two or more pieces of equipment are connected, press the
[Source Search] button until the target image is projected.
Automatically Detect Incoming Signals and Change
the Projected Image (Source Search)
You can project the target image quickly as input ports with no image
signal being input are ignored when you change by pressing the [Source
Search] button.
Computer1
Computer2
S-Video
Video
The input port where no image
signal is being input is skipped.
EasyMP *
* EasyMP changes when using EMP-1815.
Install the wireless LAN unit supplied.
Procedure
When your video equipment is connected, start playback before beginning
this operation.
Using the control panel
q
The following screen showing the status of image signals is
displayed when only the image that the projector is
currently displaying is available, or when no image signal
can be found. You can select the input port where the
connected equipment you want to use is projecting. If no
operation is performed after about 10 seconds, the screen
closes.
21
Changing the Projected Image
Changing Directly from the Remote Control
You can change directly to the target image by pressing the following
buttons on the remote control.
Remote control
Changes to images from
the Computer1 input port.
Changes to images
from the Computer2
input port.
Changes to images from
the S-Video input port.
Changes to images
from the Video input
port.
Changes to the EasyMP
image. This feature is not
provided on the EMP-1810.
(EMP-1815 only)
Functions for Enhancing Projection
Selecting the Projection Quality (Selecting Colour
Mode)
22
Procedure
Remote control
You can easily obtain the optimum image quality simply by selecting the
setting that best corresponds to your surroundings when projecting. The
brightness of the image varies depending on the mode selected.
Mode
Game
Presentation
Text
Theatre
Photo
Sports
sRGBg
Blackboard
Customized
Application
Ideal for use in a bright room. This is the brightest
mode, and reproduces shadow tones well.
Ideal for making presentations using color materials
in a bright room.
Ideal for making presentations using black-andwhite materials in a bright room.
Ideal for watching films in a dark room. Gives
images a natural tone.
(When computer images are input)
Ideal for projecting still pictures, such as photos, in a
bright room. The images are vivid and brought into
contrast.
(When component video, S-video, or composite
video images are input)
Ideal for watching TV programmes in a bright room.
The images are vivid and brought to life.
Ideal for images that conform to the sRGB colour
standard.
Even if you are projecting onto a blackboard
(greenboard), this setting gives your images a natural
tint, just like when projecting onto a screen.
Select "Customized" to adjust "R,G,B,C,M,Y" from
"Color Adjustment" in the configuration menu.
s "Color Adjustment"
Each time you press the button, the colour mode name is displayed on the
screen and the colour mode changes.
If you press the button while the colour mode name is displayed on the
screen, it changes to the next colour mode.
q
The colour mode can also be set using "Color Mode" in the
"Image" menu from the configuration menu. s p.41
23
Functions for Enhancing Projection
Hiding the Image and Sound Temporarily (A/V Mute)
You can use this when you want to focus the audience's attention on what
you are saying, or if you do not want to show details such as when you are
changing between files during presentations from a computer.
Procedure
Remote control
Projector
Each time you press the button, or the A/V mute slide is opened or closed,
A/V Mute turns on or off.
q
• If you use this function when projecting moving images,
the images and sound continue to be played back by the
source, and you cannot return to the point where A/V
Mute was activated.
• You can choose to display black, blue, or logo as the A/V
mute display using the "Extended"-"Display"-"A/V
Mute" setting from the configuration menu. s p.44
• When the A/V mute slide is closed and A/V mute begins,
the power supply can be set to automatically turn off after
about 30 minutes by setting "Extended" - "Sleep Mode"
from the configuration menu. s p.45
Functions for Enhancing Projection
Freezing the Image (Freeze)
When the moving image on the screen is frozen, the image continues to
project, so you can project a moving image one frame at a time like a still
photo. Also, you can perform operations such as changing between files
during presentations from a computer without projecting any images if the
freeze function is activated beforehand.
Procedure
Remote control
Each time you press the button, Freeze turns on or off.
q
• Audio does not stop.
• The image source continues to playback the moving
images even while the screen is frozen, and so it is not
possible to resume projection from the point where it was
paused.
• If the [Freeze] button is pressed while the configuration
menu or a help screen is displayed, the menu or help
screen being displayed is cleared.
• Freeze still works while E-Zoom is being used.
24
25
Functions for Enhancing Projection
Changing the Aspect Ratiog (Resize)
If you press the button while the aspect name is displayed on the screen, it
changes to the next aspect mode.
When video equipment is connected, images that have been recorded in
digital video or onto DVDs can be viewed in 16:9 wide-screen format.
You can change the aspect ratio for images in squeeze modeg as follows.
4:3
16:9
16:9 (Up)
16:9 (Down)
Procedure
Remote control
Each time you press the button, the aspect name is displayed on the screen
and the aspect changes.
q
The colour mode can also be set using "Resize" in the
"Signal" menu from the configuration menu. s p.42
26
Functions for Enhancing Projection
Pointer Function (Pointer)
This allows you to move a pointer icon on the projected image, and helps
you draw attention to the area you are talking about.
B Move the pointer icon.
Remote control
Pointer icon
Procedure
A
Display the pointer.
Remote control
Each time you press the button, the pointer appears or disappears.
q
You can choose from three different kinds of pointer icon
(
) in "Settings" - "Pointer Shape" from the
configuration menu. s p.43
27
Functions for Enhancing Projection
Enlarging Part of the Image (E-Zoom)
This is useful when you want to expand images to see them in greater
detail, such as graphs and tables.
the cross to the area of the image that you
B Move
want to enlarge.
Remote control
Cross
Procedure
A Start E-Zoom.
C Enlarge.
Remote control
Remote control
Each time the button is pressed, the area is expanded. You can
expand quickly by holding the button down.
You can reduce the enlarged image by pressing the [x] button.
Press the [Esc] button to cancel.
q
• The enlargement ratio appears on the screen. The selected
area can be enlarged to between 1 to 4 times in 25
incremental steps.
• Tilt the [h] button to scroll the image.
28
Functions for Enhancing Projection
Using the Remote Control to Operate the Mouse
Pointer (Wireless Mouse)
Connect the USB port of a computer and the USB port (TypeB) on the
rear of the projector with a commercially available USB cable*. If the
"Extended" - "USB TypeB" setting in the configuration menu is set to
"Wireless Mouse", you can use the projector's remote control like a
wireless mouse to control the computer's mouse pointer. s p.45
Computer
Windows 98/98SE/2000/Me/XP Home Edition/XP Professional
Macintosh (OS 8.6–9.2/10.1–10.4)
q
• It may not be possible to use the mouse function under
some versions of both the Windows and Macintosh
operating systems.
• Some computer settings may have to be changed in order
for the mouse function to be used. Consult the
documentation for the computer for further details.
Once the connection has been made, the mouse pointer can be operated as
follows.
Moving the mouse pointer
Mouse clicks
* Supplied with the EMP-1815.
Left click
Right click
Double-click: Press twice in rapid
succession.
Drag and drop
This is useful for displaying
the previous or next slide in a
PowerPoint slideshow.
To previous slide
To USB port
USB cable
To USB port
(Type B)
1. Hold down the [Enter] button and
tilt and drag the [h] button.
2. Release the [Enter] button to drop
at the desired location.
To next slide
Functions for Enhancing Projection
q
• If the mouse button settings are set to reverse on the
computer, the operation of the remote control buttons will
also be reversed.
• The wireless mouse function cannot be used while the
following functions are being used.
· While a configuration menu is being displayed
· While a help menu is being displayed
· While the E-Zoom function is being used
· While a user's logo is being captured
· Pointer function
· While adjusting sound volume
29
Remote Control of Two or More Projectors
When using two or more projectors, you can operate only the projector
having a specific ID if you register the same ID to both the projector
and the remote control.
Set the projector ID in the configuration menu. Set the remote control
ID by the [ID] button and numeric buttons on the remote control.
q
• The default projector ID is "Off" and default remote
control ID is "0".
• When the projector is turned off and turned on again, the
remote control ID returns to its default.
30
Setting the Projector ID
Procedure
the [Menu] button and select "Extended" A Press
"Projector ID" from the configuration menu.
s "Using the Configuration Menu" p.40
Using the remote control
Using the control panel
Check the buttons you can use and the operations they perform in
the guide under the menu.
the ID you want to set and press the [Enter]
B Choose
button.
31
Remote Control of Two or More Projectors
the [Menu] button to close the configuration
C Press
menu.
When this setting is completed, only operations from a remote
control having a matching ID or whose ID is set to "0" are
accepted.
Setting the Remote Control ID
You need to set the remote control ID every time you turn on the
projector.
Procedure
Point the remote control at the remote receiver on the projector you want
to operate.
A Press the [ID] button.
the numeric button of the same number as the
B Press
ID of the projector you want to operate.
You can operate only the projector with the specified ID number.
q
Checking if remote control operation is possible
You can check whether or not remote control operation is
possible on the projector to be operated with the following
procedure.
Press the [ID] button on the remote control pointing at the
remote receiver of the projector to be operated.
When remote control operations are
enabled:
Adjusting Colour for Several Projectors (Multi-Screen Colour Adjustment)
When several projectors are lined up and projecting images, you can
adjust the brightness and colour tone of each projector's image with
multi-screen colour adjustment so that the colours of images from
each projector match closely.
In some cases the brightness and colour tone may not match
completely even after adjustment.
Attention
If you use two or more projectors arranged side by side, the exhaust
from the adjacent projector might cause a high temperature
warning. So, pay attention to the following points:
• Project the image so that it is larger than 50".
• Leave at least 65 cm of space between each projector.
• Do not install projectors at locations that get hot, such as in the
direct sunlight or near air conditioner or heater exhaust ports.
Summary of Adjustment Procedure
Make adjustments according to the following procedure.
1. Setting the projector ID
Set one projector ID to each projector. s p.30
2. Setting the remote control ID
If you set the same ID as the projector you want to operate on the
remote control, too, you can operate the projector with the same ID.
s p.31
3. Making image corrections
After the projectors are setup, you can adjust the image for each
projector.
Using Image Correction you can adjust from black to white in five
stages called levels 1 to 5, and in each level 1 to 5 you can adjust the
following two points.
• Adjusting brightness
Adjust each image by levels 1 to 5 so that they are all equal.
• Adjusting colour
Adjust each image by levels 1 to 5 so that the colours match using
"Color Correct. (G/R)" and "Color Correct. (B/Y)".
32
Adjusting Colour for Several Projectors (Multi-Screen Colour Adjustment)
Image Correction Method
After setting up the projectors, adjust the brightness and tone for each
image.
Procedure
the [Menu] button and select "Extended" A Press
"Multi-screen" from the configuration menu.
s "Using the Configuration Menu" p.40
the level to be adjusted in "Adjustment
B Select
Level".
• Each time a level is selected, the pattern of the level selected is
displayed.
• You can start adjusting from any level, usually you can make it
darker or lighter by adjusting 1 to 5 or 5 to 1.
C Adjust the brightness with "Brightness Correct.".
• When you select level 5, it adjusts to the darkest image from
several projectors.
• When you select level 1, it adjusts to the brightest image from
several projectors.
• When you select level 2 to 4, it adjusts to the mid-range
brightness image from several projectors.
• Each time the [Enter] button is pressed the image displayed
changes between the pattern display and the actual image, and
you can check the adjustment results and make corrections in the
actual image.
33
"Color Correct. (G/R)" and "Color Correct.
D Adjusting
(B/Y)".
Each time the [Enter] button is pressed the image displayed
changes between the pattern display and the actual image, and you
can check the adjustment results and make corrections in the actual
image.
procedures 2 to 4 until adjustments are
E Repeat
finished.
all adjustments are finished, press the [Menu]
F When
button to close the configuration menu.
Security Functions
The projector has the following enhanced security functions.
• Password protect
You can limit who can use the projector.
• Operation Lock
You can prevent people changing the settings on the projector
without permission.
• Anti-Theft Lock
The projector is equipped with various types of anti-theft security
devices.
Managing Users (Password Protect)
When Password Protect is activated, people who do not know the
password cannot use the projector to project images even if the projector
power is on. Furthermore, the user's logo that is displayed when you turn
on the projector cannot be changed. This acts as an anti-theft device as the
projector cannot be used even if it is stolen. At the time of purchase,
Password Protect is not activated.
f Type of Password Protect
The following three kinds of password protect settings can be made
according to how the projector is being used.
1. "Power On Protect"
When "Power On Protect" is "On", the password must be entered
whenever the projector is turned on after it has been disconnected from
the power supply it was connected to the last time the password was
entered.
If the correct password is not entered, projection does not start.
34
2. "User's Logo Protect"
When "User's Logo Protect" is set to "On" the user's logo cannot be
changed and the following setting changes for user's logo are
prohibited.
• Capturing a user's logo
• Settings for "Display Background", "Startup Screen", and "A/V
Mute" from "Display" in the configuration menu.
3. "Network Protect" (EMP-1815 only)
When "Network Protect" is set to "On" setting changes for "Network"
in the configuration menu are prohibited.
35
Security Functions
f Setting Password Protect
Use the following procedure to set Password Protect.
Procedure
down the [Freeze] button for about five
A Hold
seconds.
The password protect setting menu is displayed.
Remote control
q
• If Password Protect is already activated, you must enter
the password.
If the password is entered correctly, the password protect
setting menu is displayed. s "Entering the Password"
p.36
• When the password is set, stick the password protect
sticker in a visible position on the projector as a further
theft deterrent.
B Turn on "Power On Protect".
(1) Select "Power On Protect", and then press the [Enter] button.
(2) Select "On", and then press the [Enter] button.
(3) Press the [Esc] button.
C Turn on "User's Logo Protect".
(1) Select "User's Logo Protect", and then press the [Enter] button.
(2) Select "On", and then press the [Enter] button.
(3) Press the [Esc] button.
D Turn on "Network Protect".
(1) Select "Network Protect", and then press the [Enter] button.
(2) Select "On", and then press the [Enter] button.
(3) Press the [Esc] button.
36
Security Functions
E Set the password.
f Entering the Password
(1) Select "Password", and then press the [Enter] button.
(2) The message "Change the password?" is displayed, select
"Yes" and then press the [Enter] button. The default setting for
the password is "0000". Change this to your own desired
password. If you select "No", the screen shown in step 1 is
displayed again.
(3) While holding down the [Num] button, enter a four digit
number using the numeric buttons. The number entered is
displayed as "* * * *". When you enter the fourth digit, the
confirmation screen is displayed.
Remote control
Keep
pressed
Numeric buttons
(4) Re-enter the password.
The message "Password accepted." is displayed.
If you enter the password incorrectly, a message is displayed
prompting you to re-enter the password.
When the password entry screen is displayed, enter the password using the
numeric buttons on the remote control.
Procedure
While holding down the [Num] button, enter the password
by pressing the numeric buttons.
When you enter the correct password, projection begins.
Attention
• If an incorrect password is entered three times in succession, the
message "The projector's operation will be locked." is displayed
for about five minutes, and then the projector switches to standby
mode. If this happens, disconnect the power plug from the
electrical outlet and then reinsert it and turn the projector's power
back on. The projector displays the password entry screen again
so that you can enter the correct password.
• If you have forgotten the password, make a note of the "Request
Code: xxxxx" number that appears on the screen and contact the
nearest address provided in the World-Wide Warranty Terms.
s Inquiries
• If you continue to repeat the above operation and input the wrong
password thirty times in succession, the following message is
displayed and the projector does not accept any more password
entries. "The projector's operation will be locked. Contact Epson
as described in your documentation." s Inquiries
37
Security Functions
Restricting Operation (Operation Lock)
Do one of the following to lock the operation buttons on the control panel.
• Full lock
All of the buttons on the control panel are locked. You cannot perform
any operations from the control panel, including turning the power on or
off.
• Partial lock
All of the buttons on the control panel, except for the [Power] button,
are locked.
This is useful at events or shows when you want to deactivate all buttons
and only project, or at schools when you want to limit button operation.
The projector can still be operated using the remote control.
Check the buttons you can use and the operations they perform in
the guide under the menu.
B Select either "Full Lock" or "Partial Lock".
Procedure
the [Menu] button and select "Settings" A Press
"Operation Lock". s "Using the Configuration
Menu" p.40
Using the remote control
"Yes" when the confirmation message is
C Select
displayed.
Using the control panel
The control panel buttons are locked according to the setting you
chose.
q
You can release the control panel lock by one of the
following two methods.
• From the remote control, select "Off" in "Settings" "Operation Lock" from the configuration menu.
• Press and hold down the [Enter] button on the control
panel for about seven seconds, a message is displayed and
the lock is released.
38
Security Functions
Anti-Theft Lock
As the projector is often setup on ceiling mounts and left in rooms
unattended, it is possible that someone may try and take the projector, so
the projector includes the following security devices.
• Security slot
The security slot is compatible with the Microsaver Security System
manufactured by Kensington. You can find details about the Microsaver
Security System on the Kensington homepage http://www.kensington.
com/.
• Security cable installation point
A commercially available theft-prevention wire lock can be passed
through the installation point to secure the projector to a desk or pillar.
f Installing the wire lock
Pass an anti-theft wire lock through the installation point.
See the documentation supplied with the wire lock for locking
instructions.
Configuration Menu
This chapter explains how to use the configuration menu and its functions.
Using the Configuration Menu .......................... 40
List of Functions ................................................. 41
•
•
•
•
•
Image Menu .......................................................................41
Signal Menu .......................................................................42
Settings Menu ....................................................................43
Extended Menu .................................................................44
Network Menu (EMP-1815 Only) ...................................46
Operations in the Network Menu ...................................................47
Soft keyboard operations................................................................47
Basic Menu.....................................................................................48
Wireless LAN Menu ......................................................................49
Security Menu ................................................................................50
Wired LAN Menu ..........................................................................54
Mail Menu ......................................................................................55
SNMP Menu...................................................................................56
• Info Menu (Display Only).................................................57
• Reset Menu ........................................................................58
Using the Configuration Menu
from the
A Selecting
top menu
from the
B Selecting
sub menu
40
the
C Changing
selected item
D Exit
Top menu
Guide
Sub menu (Settings)
Buttons used
Using the control panel
Select the setting to change
Using the remote control
List of Functions
41
Image Menu
Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for each
image signal.
Computer image
Sub Menu
Color Mode
Brightness
Contrastg
Color Saturation
Tint
Sharpness
Abs. Color Temp.
Color Adjustment
Reset
Component videog/Composite videog/S-videog
Function
You can select the quality of the image to suit your surroundings. s p.22
You can adjust the image brightness.
You can adjust the difference between light and shade in the images.
You can adjust the colour saturation for the images.
(Adjustment is only possible when NTSC signals are being input if you use composite video/S-video.)
You can adjust the image tint.
You can adjust the image sharpness.
You can adjust the overall tint of the image. You can adjust tints in 10 stages from 5000 K to 10000 K. When a high value is selected the image
becomes tinged with blue, when a low value is selected the image becomes tinged with red.
(This item cannot be selected if "sRGBg" is selected as the "Color Mode" setting in the "Image" menu.)
You can make adjustments by choosing one of the following
Red, Green, Blue: You can adjust the saturation of each colour individually.
(This item cannot be selected if values for "sRGBg" or "Customized" are selected from "Image" - "Color Mode".)
R, G, B, C, M, Y: You can adjust the strength of each colour R (red), G (green), B (blue), C (cyan), M (magenta), Y (yellow) individually.
(This item can only be selected when "Customized" is selected from "Image" - "Color Mode".)
You can reset all adjustment values for the "Image" menu functions to their default settings. To return all menu items to their default settings, see
s p.58
42
List of Functions
Signal Menu
Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for each
image signal.
Computer image
Sub Menu
Auto Setup
Trackingg
Sync.g
Position
Progressiveg
Computer1 Input
Computer2 Input
Video Signal
Resize
Reset
Component videog
Composite videog/S-videog
Function
You can select whether, when the input signal changes, the image is automatically adjusted to the optimum state (On) or not (Off). s p.67
You can adjust computer images when vertical stripes appear in the images. s p.67
You can adjust computer images when flickering, fuzziness, or interference appear in the images. s p.67
You can adjust the display position up, down, left, and right when a part of the image is missing so that all of the image is projected.
(Component video can only be adjusted when 525i/625i signals are being input)
Off: IP conversion is carried out for each field in the screen. This is ideal for viewing images with a large amount of movement.
On: interlaceg (i) signals are converted into progressiveg (p) signals. This is ideal for viewing still images.
You can select the input signal from the Computer1 input port or Computer2 input port.
If set to "Auto" the input signal is set automatically according to the connected equipment.
If colours do not appear correctly when set to "Auto", select the appropriate signal according to the connected equipment.
If set to "Auto", video signals are recognized automatically. If interference appears in the image or a problem occurs such as no image is being
projected when set to "Auto", select the appropriate signal according to the connected equipment.
You can set the aspect ratiog for projected images. s p.25
You can reset all adjustment values on the "Signal" menu to their default settings, except for "Computer1 Input" and "Computer2 Input".
To return all menu items to their default settings, see s p.58
43
List of Functions
Settings Menu
For EMP-1815
Sub Menu
Keystone
Operation Lock
Pointer Shape
Brightness Control
Volume
Remote Receiver
Test Pattern
Reset
For EMP-1810
Function
You can correct keystone distortion in images.
H/V Keystone : Corrects horizontal and vertical keystone distortion. Select one of "V-Keystone", "H-Keystone" and "Auto V-Keystone". If "Auto
V-Keystone" is selected and set to "On", vertical tilt of the projector is detected and automatically corrected. When set to "Off", correct manually
by the [w], [v], [<] and [>] buttons on the control panel.
"V-Keystone" and "H-Keystone" are for performing correction manually.
Quick Corner : Selects and corrects the four corners of the projected image. s p.18
You can use this to restrict operation of the projector's control panel. s p.37
You can select the shape of the pointer. s p.26
Pointer 1:
Pointer 2:
Pointer 3:
You can set the lamp brightness to one of two settings.
Select "Low" if the images being projected are too bright such as when projecting images in a dark room or onto a small screen. When "Low" is
selected, the amount of electricity consumed and the lamp's operating life are changed as follows, and fan rotation noise during projection is
reduced. Electrical consumption: about a 40 W decrease, lamp life: about 1.5 times longer
You can adjust the volume.
You can limit the reception of the operation signal from the remote control.
When you want to prohibit operation by remote control, or if the remote receiver has a fluorescent light too close to it , you can make settings to
deactivate the remote receiver you do not want used or that is experiencing interference.
When the projector is setup, a test pattern is displayed so that you can adjust the projection without connecting other equipment. While the test
pattern is displayed, zoom and focus adjustments, and keystone correction, excluding Quick Setup, can be performed.
To cancel the test pattern, press the [Esc] button on the remote control or the control panel.
You can reset all adjustment values for the "Settings" menu to their default settings.
To return all menu items to their default settings, see s p.58
44
List of Functions
Extended Menu
For EMP-1815
Sub Menu
Display
For EMP-1810
Function
You can make settings related to the projector's display.
Messages: You can set whether to display (On) or not display (Off) the source name when you change the input source, the colour mode name when
you change the colour mode, a message when no image signal is input, and so on.
Display Background*: You can set the screen status for when no image signal is available to "Black", "Blue", or "Logo".
Startup Screen*: You can set if the startup screen (the image projected when starting the projector) is displayed or not.
A/V Mute*: You can set the screen displayed during A/V Mute as "Black", "Blue", or "Logo".
You can change the user's logo that is displayed as a background and displayed during A/V Mute. s p.79
User's Logo*
Projection
You can set from the following according to the way the projector is setup. s p.72
"Front" "Front/Ceiling" "Rear" "Rear/Ceiling"
You can change the setting as follows by pressing down the [A/V Mute] button on the remote control for about five seconds.
"Front"W"Front/Ceiling"
"Rear"W"Rear/Ceiling"
* When "User's Logo Protect" is set to "On" in "Password Protect", settings concerning user's logo cannot be changed. You can make changes after setting "User's
Logo Protect" to "Off". s p.35
List of Functions
Sub Menu
Operation
45
Function
Direct Power On: You can set whether Direct Power On is enabled (On) or disabled (Off).
When it is set to "On" and the projector power cable is connected to an electrical outlet, be aware that sudden surges of electricity when power
comes back on after a power outage may cause the projector to turn on automatically.
Sleep Mode: You can set whether projection stops automatically (On) or not (Off) when no operations are carried out for about 30 minutes while no
image signal is being input, or when about 30 minutes have elapsed since the A/V mute slide is closed.
Sleep mode is set to (Off) at the time of purchase, so do not forget to turn off the power after projecting.
High Altitude Mode: Set to "On" when using the projector above an altitude of 1500 m.
Standby Mode
You can use network monitoring and control functions while the projector is in standby mode when this is set to "Network On".
You can use SNMPg to monitor and control the status of the projector over the network, or by using the "EMP Monitor" software supplied with this
product.
USB Type B
Set to "USB Display" when the projector and a computer are connected by a USB cable and computer images are projected. s Wireless LAN
(EMP-1815 only)
Quick Connection Guide
Set to "Wireless Mouse" when the mouse pointer is to be operated by the remote control. s p.28
Projector ID
Set the ID within the range "1" to "9". "Off" indicates that no ID is set. s p.30
Multi-screen
You can adjust the hue and brightness of each projected image when multiple projectors are lined up and projecting. s p.32
Adjustment Level: You can adjust from black to white in five stages called levels 1 to 5, and in each level 1to 5 you can adjust "Brightness
Correct." and "Color Correct".
Brightness Correct.: Corrects the difference in the brightness of each product.
Color Correct. (G/R) / Color Correct. (B/Y): You can correct the difference in the colour of each product.
Language
You can set the language for message displays.
Reset
You can reset "Display*1" and "Operation*2", in the "Extended" menu to their default settings.
To return all menu items to their default settings, see s p.58
*1 When "User's Logo Protect" is set to "On" in "Password Protect", settings relating to user's logo cannot be changed. You can make changes after setting "User's
Logo Protect" to "Off". s p.35
*2 Except for "High Altitude Mode".
46
List of Functions
Network Menu (EMP-1815 Only)
When "Network Protect" is set to "On" in "Password Protect", a message is displayed and the settings cannot be changed. You can make changes after
setting "Network Protect" to "Off". s p.35
Sub Menu
To Network
Configuration
q
Function
The display changes to the Network menu so that you can make network settings.
The following menus are available for network settings: "Basic", "Wireless LAN menu", "Security Menu", "Wired LAN Menu", "Mail notification
menu", "SNMP menu", and "Complete menu". Once the required items are set up, the projector can be connected to a computer over the network.
The projector's functions can be set and the projector can be controlled from a computer by using the Web browser on a computer connected
to the projector on a network. sEasyMP Operation Guide
Settings that involve input of text from Web control also can be performed easily as a keyboard can be used to input the settings.
47
List of Functions
f Operations in the Network Menu
The screen returns to the configuration menu.
Selection from the top menu, selection of submenus, and changing of
selected items are the same as operations in the configuration menu.
Top menu
Sub menu (Settings)
f Soft keyboard operations
Guide
However, to exit, the following operation is needed. Go to "Complete
menu", and select one of "Yes", "No" or "Cancel".
Yes:
No:
Cancel:
Saves the settings and exits the network menu.
Exits the network menu without saving the settings.
Display of the network menu is continued.
The network menu contains items that require input of alphanumerics
during setup. In this case, the following software keyboard is displayed.
Move the cursor to the desired key by the [h] button on the remote
control or [w], [v], [<] or [>] on the projector, and press the [Enter]
button to enter the alphanumeric. After inputting, press [Finish] on the
keyboard to confirm your input. Press [Cancel] on the keyboard to cancel
your input.
Each time this key is
selected, it sets and
changes between upper
case and lower case
letters.
Each time this key is
selected, it sets and
changes the symbol
keys for the section
enclosed by the frame.
List of Functions
48
f Basic Menu
Sub Menu
Projector name
PJLink Password
Web Control
Password
Projector keyword
Function
You can enter a name for the projector. When connected to a network, this name is used to identify the projector. The initial value is "EMPxxxxxx"
(where xxxxxx are the last six digits of the MAC Address). You can enter up to 16 single-byte alphanumeric characters.
Enter a password to use when you access the projector using compatible PJLink software. s p.91
You can enter up to 32 single-byte alphanumeric characters.
Enter a password to use when making settings and controlling the projector using Web control.* You can enter up to 8 single-byte alphanumeric
characters. Web control is a computer function that allows you to set up and control the projector by using the Web browser on a computer
connected on a network. sEMP Monitor Operation Guide
When projector keyword is set to "ON", you have to enter the keyword when you try to connect to a network. When using this function, you can
prevent presentations from being interrupted by unscheduled connections from the computer.
Normally this should be set to "ON".
49
List of Functions
f Wireless LAN Menu
Sub Menu
Connection mode
Antenna level
Wireless LAN
system
ESSIDg
Function
Sets the connection mode.
Set "Quick" to establish a quick wireless connection in a 1:1 configuration. Set "Advanced" to connect to the network system via an access point.
Displays the wireless LAN wave strength.
Sets the wireless LAN system.
Enter an ESSID. When an ESSID is provided for the wireless LAN system in which the projector participates, enter the ESSID. The initial value is
EPSON.
You can enter up to 32 single-byte alphanumeric characters.
DHCPg
You can set whether to use DHCP (On) or not (Off).
If this is set to "On" you cannot set any more addresses.
IP addressg
You can input the IP address assigned to the projector.
You can enter a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
Subnet maskg
You can input the subnet mask for the projector. You can enter a number from 0 to 255 in each field of the address. However, the following subnet
masks cannot be used.
0.0.0.0, 255.255.255.255
Gateway addressg You can input the IP address for the gateway for the projector.
You can enter a number from 0 to 255 in each field of the address. However, the following gateway addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
50
List of Functions
f Security Menu
Sub Menu
Security
Function
Select the security type from the items that are displayed. sEasyMP Operation Guide
When setting up security, follow the instructions from the administrator of the network system you are about to access.
Type of security
When connecting and communicating in wireless LAN mode, you can select one of the following encryption and authentication methods.
• WEP
Data is encrypted with a code key (WEP key)
This mechanism prevents communication unless the encrypted keys for the access point and the projector match.
• WPA
This is an encryption standard that improves security which is a weak point of WEP. Although there are several kinds of WPA encryption methods, this
projector uses "TKIPg". TKIP uses PSK to automatically update the encryption key at regular fixed intervals, which makes it harder to break compared to
WEP which uses a constant encryption key.
WPA also includes user authentication functions. WPA authentication provides two methods: using an authentication server, or authenticating between a
computer and an access point without a server. This projector supports the latter method, without a server.
• EAP
EAP is a protocol used for communication between clients and authentication severs. These are several protocols, such as EAP-TLS which uses electronic
certification for user authentification, LEAP which uses user ID and password, and EAP-TTLS.
51
List of Functions
System
EAP-TLS
EAP-TTLS
PEAP/MS-CHAPv2
PEAP/EAP-GTC
LEAP
q
Authentication
Electronic certification, CA certification
User ID, Password
User ID, Password
User ID, Password
User ID, Password
Notes
Funk Software Company
Microsoft Corporation
Cisco Systems Company
Cisco Systems Company
• For setting details, follow the directions from the network administrator of your network.
• If using EAP, you need to make settings at the projector that match the authentication server settings. Check with your network
administrator for details on RADIUS settings.
• Register an electronic certificate and a CA certificate to the projector. Only one set of an electronic certificate and a CA certificate can be
registered to the projector. These certificates are used with EAP-TLS.
List of Functions
52
When WEP is selected
Sub Menu
Function
WEP encryption
You can set the encryption for WEP encoding.
128 bit: Uses 128 (104) bit encoding
64 bit: Uses 64 (40) bit encoding
Format
You can set the input method for the WEP encrypted key.
ASCII: Input text.
HEX: Input in hexadecimal.
Key ID
Selects the WEP encryption ID key.
Encryption key 1/
You can enter the key used for WEP encryption. Enter the key in single-byte characters following instructions from the network administrator for
Encryption key 2/
the network in which the projector participates. The type of character and the number that can be entered differ according to the "WEP Encryption"
Encryption key 3/
and "Format" settings.
Encryption key 4
If the number of characters you enter is shorter than the required character length, no character is encrypted. If the number of characters you enter is
longer than the required character length, characters that exceed the permitted number are not encrypted.
"128 bit" - when "ASCII": Single-byte alphanumerics, up to 13 characters max.
"64 bit" - when "ASCII": Single-byte alphanumerics, up to 5 characters max.
"128 bit" - when "HEX": 0 to 9 and A to F, up to 26 characters
"64 bit" - when "HEX": 0 to 9 and A to F, up to 10 characters
53
List of Functions
When WPA-PSK (TKIP) or WPA2-PSK (AES) are selected
Sub Menu
Function
PSK (Encryption
You can enter a PreSharedKey (encrypted key) in single-byte alphanumeric characters. Enter at least 8 and up to 64 characters. When the
key)
PreSharedKey is entered and the [Enter] button is pressed, the value is set and displayed as an asterisk (*).
You cannot enter more than 32 characters on the option settings menu. When setting from Web Control, you can enter more than 32 characters.
sEasyMP Operation Guide
When EAP-TLS is selected
Sub Menu
Issued to/Issued
Information in the certificate is displayed. You cannot enter.
by/Validity period
Function
When EAP-TTLS/MD5, EAP-TTLS/MS-CHAPv2, PEAP/MS-CHAPv2, PEAP/GTC, LEAP, EAP-Fast/MS-CHAPv2 or EAP-FAST/GTC are selected
Sub Menu
Function
User name
You can enter a user name to be used for authentication in single-byte alphanumeric characters (no spaces). You can enter up to 64 characters.
You cannot enter more than 32 characters on the configuration menu. When setting from Web Control, you can enter more than 32 characters.
sEasyMP Operation Guide
Password
You can enter an authentication password in single-byte alphanumeric characters. You can enter up to 64 characters. When the password is entered
and the [Enter] button is pressed, the value is set and displayed as an asterisk (*).
You cannot enter more than 32 characters on the configuration menu. When setting from Web Control, you can enter more than 32 characters.
sEasyMP Operation Guide
54
List of Functions
f Wired LAN Menu
Sub Menu
DHCPg
Function
You can set whether to use DHCP (On) or not (Off).
If this is set to "On" you cannot set any more addresses.
IP addressg
You can input the IP address assigned to the projector.
You can enter a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
Subnet maskg
You can input the subnet mask for the projector. You can input a number from 0 to 255 in each field of the address. However, the following subnet
masks cannot be used.
0.0.0.0, 255.255.255.255
Gateway addressg You can input the IP address for the gateway for the projector.
You can enter a number from 0 to 255 in each field of the address. However, the following gateway addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
55
List of Functions
f Mail Menu
When this is set, if the projector enters an abnormal/warning state, you are notified by e-mail.
Sub Menu
Mail Notification
SMTP server
Port Number
Email Address 1/
Email Address 2/
Email Address 3
Setting a
Notification Event
Function
You can set whether to be notified by mail (On) or not (Off).
You can input the IP addressg for the SMTP server for the projector.
You can input a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used.
127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
You can input the port number for the SMTP server. The initial value is 25. You can input numbers between 1 to 65535.
You can input the e-mail address of the destination to send the notification mail to. You can register up to three destinations. You can enter up to 32
single-byte alphanumeric characters for the mail addresses.
You can select the abnormalities or warnings to be notified about by mail. When the selected abnormality or warning occurs in the projector, a mail
is sent to the specified "Destination address" notifying that an abnormality or warning has occurred. You can select multiple items from the
displayed items.
List of Functions
f SNMP Menu
You can set the SNMPg. To use SNMP to monitor the projector, you need to install the SNMP manager program on your computer. SNMP should be
managed by a network administrator.
Sub Menu
Function
SNMP trap IP
You can register up to two for the SNMP trap notification destination.
addressg 1/ SNMP The IP addressg registered in "Trap IP Address 2" is used when the IP address in "Trap IP Address 1" cannot be accessed.
trap IP address 2
You can enter a number from 0 to 255 in each field of the address.
However, the following IP addresses cannot be used.
127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
56
57
List of Functions
Info Menu (Display Only)
Lets you check the status of the image signals being projected and the status of the projector. Items displayed vary depending on the image signal currently
being projected as shown in the following screen shots.
Computer image/Component videog
Sub Menu
Lamp Hours
Composite videog/S-videog
EasyMP
Function
You can display the cumulative lamp operating time*.
When it reaches the lamp warning time, the characters are displayed in yellow.
Source
You can display the input port name for the connected equipment currently being projected.
Input Signal
You can display the content of "Computer1" or "Computer2" set in the "Signal" menu according to the "Source".
Resolution
You can display the input resolution.
Video Signal
You can display the content of "Video Signal" set in the "Signal" menu.
Refresh Rateg
You can display the refresh rate.
Syncg Info
You can display the image signal information.
This information may be needed if service is required.
Status
This is information about errors that have occurred on the projector.
This information may be needed if service is required.
* The cumulative use time is displayed as "0H" for the first 10 hours.
List of Functions
58
Reset Menu
Sub Menu
Reset All
Function
You can reset all items in all menus to their default settings.
The following items are not reset to their defaults: "Computer1 Input", "Computer2 Input", "User's Logo", "Multi-screen", all items for "Network"
menus, "Lamp Hours", and "Language".
Reset Lamp Hours You can clear the cumulative lamp hours use time, and return it to "0H". Reset when you replace the lamp.
Troubleshooting
This chapter describes how to identify problems and what to do if a problem is found.
Using the Help..................................................... 60
Problem Solving ................................................. 61
• Reading the Indicators......................................................61
t Power indicator lights red ..........................................................62
i · o Indicator is lit or flashing orange.........................................63
• When the Indicators Provide No Help ............................64
Problems relating to images ...........................................................65
Problems when projection starts.....................................................69
Other problems ...............................................................................69
Using the Help
60
If a problem occurs with the projector, Help uses on-screen displays to
assist you in solving the problem.
C Confirm the selection.
Using the remote control
Using the control panel
Procedure
A Press the [Help] button.
The help screen is displayed.
Using the remote control
Using the control panel
Questions and solutions are displayed as shown on the screen
below.
Press the [Help] button to exit Help.
B Select a menu item.
q
Using the remote control
Using the control panel
If Help does not provide a solution to the problem, refer to
"Problem Solving" (s p.61).
Problem Solving
61
If you are having a problem with the projector, first check the projector's indicators and refer to "Reading the Indicators" below.
If the indicators do not show clearly what the problem might be, refer to "When the Indicators Provide No Help". s p.64
Reading the Indicators
The projector is provided with the following three indicators that indicate the operating status of the projector.
Indicates the operating status.
Orange
Green
Green
: Standby condition
When the [Power] button is pressed in this condition, projection starts.
: Warm-up in progress
Warm-up time is about 30 seconds. After warm-up is complete, the indicator stops flashing.
: Projection in progress
Indicates the projection lamp status.
Indicates the internal temperature status.
Refer to the following table to see what the indicators mean and how to remedy problems that they indicate.
If all indicators are off, check that the power cable is connected correctly and that the power is being supplied normally.
Sometimes, when the power cable is unplugged, the t indicator remains lit for a short period, this is not a fault.
62
Problem Solving
f t Power indicator lights red
Abnormal
: Lit
Status
Red
Red
Red
: Flashing:
: Off
Cause
Internal Error
Remedy or Status
Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest
address provided in the World-Wide Warranty Terms. s Inquiries
Red
Red
Fan Error
Sensor Error
Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest
address provided in the World-Wide Warranty Terms. s Inquiries
Red
Red
High Temp Error
(overheating)
The lamp turns off automatically and projection stops. Wait for about five minutes. After about five minutes the projector
switches to standby mode, so check the following two points.
• Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
• If the air filter is clogged, clean or replace it. s p.73, 78
If the error continues after checking the points above, stop using the projector, disconnect the power cable from the
electrical outlet, and contact your local dealer or the nearest address provided in the World-Wide Warranty Terms.
s Inquiries
When using at an altitude of 1500 m or more, set "High Altitude Mode" to "On". s p.45
Check the following two points.
• Take out the lamp and check if it is cracked. s p.75
• Clean the air filter. s p.73
If it is not cracked _ Re-fit the lamp and turn on the power.
If the error continues _ Replace the lamp with a new lamp and turn on the power.
If the error continues _ Stop using the projector, disconnect the power cable from the electrical outlet, and contact
your local dealer or the nearest address provided in the World-Wide Warranty Terms.
s Inquiries
If it is cracked _ Replace it with a new lamp, or contact your local dealer for further advice. If replacing the lamp
yourself, be careful to avoid pieces of broken glass (you cannot continue projecting until the lamp is
replaced).
Check that the lamp cover and the lamp are securely installed. s p.75
If the lamp cover or the lamp is not securely installed, the lamp does not switch on.
When using at an altitude of 1500 m or more, set "High Altitude Mode" to "On". s p.45
Red
Red
Lamp Error
Lamp Failure
Lamp Cover Open
63
Problem Solving
f i · o Indicator is lit or flashing orange
Warning
: Lit
Status
Red
Orange
Orange
q
: Flashing
: Off
: Varies according to the projector status
Cause
High Temp Warning
Remedy or Status
(This is not an abnormality. However, if the temperature rises too high again, projection stops automatically.)
• Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
• If the air filter is clogged, clean or replace it. s p.73, 78
Replace Lamp
Replace it with a new lamp. s p.75
If you continue to use the lamp after the replacement period has passed, the possibility that the lamp may explode
increases. Replace it with a new lamp as soon as possible.
• If the projector is not operating properly, even though the indicators are all showing normal, refer to "When the Indicators Provide No
Help" (s p.64).
• If an indicator is displaying a status not described in the tables, contact your local dealer or the nearest address provided in the World-Wide
Warranty Terms. s Inquiries
64
Problem Solving
When the Indicators Provide No Help
If any of the following problems occur and the indicators do not offer a
solution, refer to the pages given for each problem.
Problems relating to images
f No images appear s p.65
Projection does not start, the projection area is completely black, the
projection area is completely blue, and so on.
f Moving images are not displayed s p.65
Moving images being projected from a computer appear black and
nothing is projected.
f Projection stops automatically s p.65
f The message "Not supported." is displayed s p.66
f The message "No Signal." is displayed s p.66
f Images are fuzzy or out of focus s p.66
f Interference or distortion appears in images s p.67
Problems such as interference, distortion, or black & white checked
patterns appear.
f The image is truncated (large) or small, or the aspect is not
suitable s p.67
Only part of the image is displayed, or the height and width ratios of the
image are not correct, and so on.
f Image colours are not right s p.68
The whole image appears purplish or greenish, images are black & white,
colours appear dull, and so on.
(Computer monitors and LCD screens have different colour reproduction
performance, so that the colours projected by the projector and the
colours appearing on the monitor may not necessarily match, but this is
not a sign of a problem.)
f Images appear dark s p.68
f Nothing appears on the external monitor s p.68
Problems when projection starts
f Power does not turn on s p.69
Other problems
f No sound can be heard or the
sound is faint s p.69
f The remote control does not work
s p.69
f Mail is not received even if an
abnormality occurs in the
projector s p.70
65
Problem Solving
f Problems relating to images
f No images appear
Check
Did you press the [Power] button?
Are the indicators switched off?
Is A/V Mute active?
Is the A/V mute slide closed?
Are the configuration menu settings correct?
Is the projected image completely black?
Remedy
Press the [Power] button to turn the power on.
The power cable is not connected correctly or power is not being supplied normally.
Connect the projector's power cable correctly. sQuick Start Guide
Check that your electrical outlet or power source is functioning correctly.
Press the [A/V Mute] button on the remote control to cancel A/V Mute. s p.23
Open the A/V mute slide.
Reset all of the settings. s"Reset"-"Reset All" p.58
Some input images, such as screen savers, may be completely black.
Only when projecting computer images
Is the image signal format setting correct?
Change the setting according to the signal for the connected equipment. s"Signal"-"Video Signal" p.42
Only when projecting images from a video source
f Moving images are not displayed
Check
Is the computer's image signal being output to the LCD and
the monitor?
Remedy
Change the image signal to external output only. s Check your computer's documentation.
Only when projecting images from a laptop
computer or a computer with a built-in LCD screen
f Projection stops automatically
Check
Is "Sleep Mode" set to "On"?
Remedy
Press the [Power] button to turn the power on. If you do not want to use "Sleep Mode", change the setting to
"Off". s"Extended"-"Operation"-"Sleep Mode" p.45
66
Problem Solving
f The message "Not supported." is displayed
Check
Is the image signal format setting correct?
Remedy
Change the setting according to the signal for the connected equipment. s"Signal"-"Video Signal" p.42
Only when projecting images from a video source
Do the image signal resolution and the refresh rate
correspond to the mode?
Refer to the computer's documentation for how to change the image signal resolution and the refresh rate
output from the computer. s"List of supported monitor displays" p.92
Only when projecting computer images
f The message "No Signal." is displayed
Check
Are the cables connected correctly?
Is the correct input port selected?
Remedy
Check that all the cables required for projection are securely connected. sQuick Start Guide
Change the image by pressing the [Source Search] button on the remote control or the control panel.
s p.20
Is the power for the computer or video source turned on?
Turn the power on for the equipment.
Are the image signals being output to the projector?
If the image signals are only being output to the computer's LCD monitor or to the accessory monitor, you
need to change the output to an external destination as well as the computer's own monitor. For some
Only when projecting images from a laptop
computer or a computer with a built-in LCD screen computer models, when the image signals are output externally, they no longer appear on the LCD monitor
or accessory monitor. sComputer's documentation, under a title such as "External output" or "Connecting
an external monitor".
If the connection is made while the power of the projector or computer is already turned on, the function
[Fn] key that changes the computer's image signal to external output may not work. Turn the power for the
computer and the projector off and then back on again. sQuick Start Guide
f Images are fuzzy or out of focus
Check
Is the focus adjusted correctly?
Is the projector at the correct distance?
Is the Keystone adjustment value too large?
Has condensation formed on the lens?
Remedy
Turn the focus ring to adjust the focus. sQuick Start Guide
The recommended projection distance ranges from 83 to 1469 cm (33 to 578 in.).
Setup within this range. s p.81
Lower the projection angle to reduce the amount of keystone correction. sQuick Start Guide
If the projector is suddenly taken from a cold environment to a warm environment, or if sudden ambient
temperature changes occur, condensation may form on the surface of the lens, and this may cause the images
to appear fuzzy. Set the projector up in the room about one hour before it is used. If condensation forms on
the lens, turn the projector off and wait for the condensation to disappear.
67
Problem Solving
f Interference or distortion appear in images
Check
Is the image signal format setting correct?
Remedy
Change the setting according to the signal for the connected equipment. s"Signal"-"Video Signal" p.42
Only when projecting images from a video source
Are the cables connected correctly?
Is an extension cable being used?
Is the correct resolution selected?
Only when projecting computer images
Are the "Sync.g" and "Trackingg" settings adjusted
correctly?
Only when projecting computer images
Check that all the cables required for projection are securely connected. sQuick Start Guide
If an extension cable is used, electrical interference may affect the signals. Use the cables supplied with the
projector to check if the cables you are using may be causing the problem.
Set the computer so that the signals being output are compatible with this projector.
s "List of Supported Monitor Displays" p.92 sComputer documentation
Press the [Auto] button on the remote control or the [Enter] button on the control panel to perform automatic
adjustment. If the images are not adjusted correctly after using automatic adjustment, you can make the
adjustments using "Sync." and "Tracking" from the configuration menu. s"Signal"-"Tracking", "Sync."
p.42
f The image is truncated (large) or small, or the aspect is not suitable
Check
Is a wide panel computer image being projected?
Only when projecting computer images
Is the image still being enlarged by E-Zoom?
Is "Position" adjusted correctly?
Is the computer set for dual display?
Only when projecting computer images
Is the correct resolution selected?
Only when projecting computer images
Remedy
Press the [Resize] button on the remote control to change the aspect mode in the order of "Normal", "4:3",
and "16:9". Change the aspect mode according to the resolution.
Press the [Esc] button on the remote control to cancel E-Zoom. s p.27
Press the [Auto] button on the remote control or the [Enter] button on the control panel to perform automatic
adjustment of the computer image being projected. If the images are not adjusted correctly after using
automatic adjustment, you can make the adjustments using "Position" from the configuration menu.
Apart from computer image signals, you can adjust other signals while projecting by adjusting "Position"
from the configuration menu. s"Signal"-"Position" p.42
If dual display is activated in the "Display Properties" of the computer's control panel, only about half of the
image on the computer screen is projected. To display the entire image on the computer screen, turn off the
dual display setting. sComputer video driver documentation
Set the computer so that the signals being output are compatible with the projector.
s "List of Supported Monitor Displays" p.92 sComputer documentation
68
Problem Solving
f Image colours are not right
Check
Do the input signal settings match the signals from the
connected device?
Is the image brightness adjusted correctly?
Are the cables connected correctly?
Is the "contrastg" setting adjusted correctly?
Is the colour adjusted correctly?
Are the colour saturation and tint adjusted correctly?
Only when projecting images from a video source
Remedy
Change the following settings according to the signal for the connected equipment.
In case of an image from a computer connected to the Computer1, Computer2 input terminal s"Signal""Computer1/2 Input" p.42
When projecting images from equipment connected to Video or S-Video s"Signal"-"Video Signal" p.42
Adjust the "Brightness" setting from the configuration menu. s"Image"-"Brightness" p.41
Check that all the cables required for projection are securely connected. sQuick Start Guide
Adjust the "Contrast" setting from the configuration menu. s"Image"-"Contrast" p.41
Adjust the "Color Adjustment" setting from the configuration menu. s"Image"-"Color Adjustment" p.41
Adjust the "Color Saturation" and "Tint" settings from the configuration menu. s"Image"-"Color
Saturation", "Tint" p.41
f Images appear dark
Check
Are the image brightness and luminance adjusted correctly?
Is the "contrastg" setting adjusted correctly?
Is the lamp due for replacement?
Remedy
Adjust the "Brightness" and "Brightness Control" settings from the configuration menu.
s"Image"-"Brightness" p.41 s"Settings"-"Brightness Control" p.43
Adjust the "Contrast" setting from the configuration menu.
s"Image"-"Contrast" p.41
When the lamp is nearly ready for replacement, the images become darker and the colour quality becomes
poorer. When this happens, replace the lamp with a new lamp. s p.75
f Nothing appears on the external monitor
Check
Remedy
Are images from a port other than the Computer1 port being The only images that can be displayed on an external monitor are computer images from Computer1 port.
projected?
s p.85
69
Problem Solving
f Problems when projection starts
f Power does not turn on
Check
Did you press the [Power] button?
Are the indicators switched off?
Do the indicators turn on and off when the power cable is
touched?
Is the operation lock set to "Full Lock"?
Is the correct setting for the remote receiver selected?
Was the power cable plugged back in immediately after
Direct Power Off, or is the breaker turned off?
Remedy
Press the [Power] button to turn the power on.
The power cable is not connected correctly or power is not being supplied normally.
Connect the projector's power cable correctly. sQuick Start Guide
Check that your electrical outlet or power source is functioning correctly.
There is probably a poor contact in the power cable, or the power cable may be defective. Reinsert the power
cable. If this does not solve the problem, stop using the projector, disconnect the power cable from the
electrical outlet, and contact your local dealer or the nearest address provided in the World-Wide Warranty
Terms. s Inquiries
Press and hold down the [Enter] button on the control panel for about seven seconds, a message is displayed
and the lock is released. s p.37
Check the "Remote Receiver" from the configuration menu. s"Settings"-"Remote receiver" p.43
When the operation to the left is performed when "Direct Power On" is set to "On", the power may not turn
back on. [Power]Press the button to turn the power back on.
f Other problems
f No sound can be heard or the sound is faint
Check
Is the audio source connected correctly?
Is the volume adjusted to the minimum setting?
Is A/V Mute active?
Is the audio cable's specification "No resistance"?
Remedy
Check that the cable is connected to the Audio port.
Adjust the volume so that sound can be heard. sQuick Start Guide
Press the [A/V Mute] button on the remote control to cancel A/V Mute. s p.23
When using a commercially available audio cable, make sure it is labeled "No resistance".
f The remote control does not work
Check
Remedy
Is the remote control light-emitting area pointing towards the Point the remote control towards the remote receiver.
remote receiver on the projector when it is operated?
The operating angle for the remote control is about 30° horizontally, and about 15° vertically. sQuick Start
Guide
Is the remote control too far from the projector?
The operating range for the remote control is about 6 m. sQuick Start Guide
70
Problem Solving
Check
Is direct sunlight or strong light from fluorescent lamps
shining onto the remote receiver?
Is the correct setting for the remote receiver selected?
Are the remote control ID and the projector ID matched?
Are the batteries dead or have the batteries been inserted
correctly?
Was a remote control button pressed for more than 30
seconds?
Remedy
Set the projector up in a location where strong light does not shine onto the remote receiver. Or set the
remote receiver to "Off" from "Remote Receiver" in the configuration menu. s"Settings"-"Remote
receiver" p.43
Check the "Remote Receiver" from the configuration menu. s"Settings"-"Remote receiver" p.43
Press the [ID] button on the remote control pointing at the remote receiver of the projector to be operated.
When the remote control operation is disabled, turn off the projector and then turn it on again.s p.31
Make sure the batteries are inserted correctly or replace the batteries with new ones if necessary. s p.74
If any of the buttons on the remote control are pressed down for more than 30 seconds, the remote control
stops sending signals (remote control's sleep mode). This feature is to prevent the batteries running down if
the remote control buttons are held down accidentally such as when it is stored in a bag or if an object is
placed on top of it. When the button is released, normal remote control operation resumes.
f Mail is not received even if an abnormality occurs in the projector (EMP-1815 only)
Check
Is "Standby Mode" set to "Network On"?
Did a fatal abnormality occur and the projector come to a
sudden stop?
Is power being supplied to the projector?
Is the LAN cable connected correctly?
Is "Mail" set correctly in the configuration menu?
Remedy
To use the mail notification function when the projector is in standby, set "Network On" in "Standby Mode"
from the configuration menu. s"Extended"-"Standby Mode" p.45
When the projector comes to a sudden stop, mail cannot be sent.
If the abnormal state continues, contact your local dealer or the nearest address provided in the World-Wide
Warranty Terms. s Inquiries
Check that your electrical outlet or power source is functioning correctly.
Check that the LAN cable is connected correctly. Reconnect it if it is not connected or it is not connected
correctly. s p.86
Mail notification of abnormalities is sent according to the "Mail" settings in the configuration menu.
Check if it is set correctly. s"Network"-"Mail" p.55
Appendices
This chapter provides information on maintenance procedures to ensure the best level of performance from the projector for a long time to come.
Installation Methods ........................................... 72
Cleaning............................................................... 73
• Cleaning the Projector's Surface .....................................73
• Cleaning the Lens..............................................................73
• Cleaning the Air Filter and Air Intake Vent ..................73
Replacing Consumables .................................... 74
• Replacing the Remote Control Batteries ........................74
• Replacing the Lamp ..........................................................75
Lamp replacement period...............................................................75
How to replace the lamp.................................................................75
Resetting the lamp operating time..................................................77
• Replacing the Air Filter....................................................78
Air filter replacement period ..........................................................78
How to replace the air filter............................................................78
Saving a User’s Logo ......................................... 79
Screen Size and Distance .................................. 81
Connecting USB Devices
(Digital Camera, Hard Disk Drive or Memory
Devices) (EMP-1815 Only).................................. 82
• Connecting USB Devices ..................................................82
Inserting and Ejecting CompactFlash Cards
(EMP-1815 Only) ................................................. 83
• How to Insert Cards..........................................................83
• How to Remove Cards ......................................................83
Card Slot Access Indicator Statuses...............................................84
Connecting to External Equipment ...................85
• Connecting to an External Monitor................................ 85
• Connecting to External Speakers.................................... 85
Connecting a LAN Cable ....................................86
Optional Accessories and Consumables .........87
Optional accessories....................................................................... 87
Consumables .................................................................................. 87
Glossary...............................................................88
ESC/VP21 Commands ........................................90
• Command List .................................................................. 90
• Cable Layouts ................................................................... 90
Serial connection............................................................................ 90
PJLink (EMP-1815 Only) .....................................91
List of Supported Monitor Displays ..................92
Computer image............................................................................. 92
Component video ........................................................................... 92
Composite video/S-video............................................................... 92
Specifications......................................................93
Appearance..........................................................97
Index.....................................................................98
Installation Methods
The projector supports the following four different projection methods.
Attention
• A special method of installation is required when suspending the
projector from a ceiling (ceiling mount). If it is not installed
correctly, it could fall causing an accident and injury.
• If you use adhesives on the ceiling mount to prevent the screws
from loosening, or if you use things such as lubricants or oils on
the projector, the projector case may crack causing it to fall from
its ceiling mount. This could cause serious injury to anyone under
the ceiling mount and could damage the projector.
When installing or adjusting the ceiling mount, do not use
adhesives to prevent the screws from loosening and do not use oils
or lubricants and so on.
• Do not use the projector on its side. This may cause malfunctions
to occur.
72
• Project images from in front
of the screen. (Front
projection)
• Project images from behind a
translucent screen. (Rear
projection)
• Suspend the projector from
the ceiling and project images
from in front of the screen.
(Front/Ceiling projection)
• Suspend the projector from
the ceiling and project images
from behind a translucent
screen. (Rear/Ceiling
projection)
q
• An optional ceiling mount is required when suspending
the projector from a ceiling. s p.87
• You can change the setting as follows by pressing down the
[A/V Mute] button on the remote control for about five
seconds.
"Front" W "Front/Ceiling"
Set "Rear" or "Rear/Ceiling" from the configuration
menu. s p.44
Cleaning
You should clean the projector if it becomes dirty or if the quality of
projected images starts to deteriorate.
Cleaning the Projector's Surface
Clean the projector's surface by wiping it gently with a soft cloth.
If the projector is particularly dirty, moisten the cloth with water
containing a small amount of neutral detergent, and then firmly wring the
cloth dry before using it to wipe the projector's surface.
73
Attention
If dust collects on the air filter it can cause the internal temperature
of the projector to rise, and this can lead to problems with operation
and shorten the optical engine's service life. Clean the air filter
immediately when the message is displayed.
Attention
Do not use volatile substances such as wax, alcohol, or thinner to
clean the projector's surface. The quality of the case may change or
become discoloured.
Cleaning the Lens
Use a commercially available cloth for cleaning classes to gently wipe the
lens.
Attention
Do not rub the lens with harsh materials or subject the lens to
shocks, as it can easily become damaged.
Cleaning the Air Filter and Air Intake Vent
Clean the air filter and the air intake vent when the following message is
displayed.
"The projector is overheating. Make sure nothing is blocking the air vent,
and clean or replace the air filter." s "How to replace the air filter" p.78
q
• If a message is frequently displayed, even after cleaning, it
is time to replace the air filter. Replace it with a new air
filter. s p.78
• It is recommended that you clean these parts at least once
every three months. Clean them more often than this if
using the projector in a particularly dusty environment.
Replacing Consumables
This section explains how to replace the remote control batteries, the
lamp, and the air filter.
74
B Replace the old batteries with new batteries.
Attention
Replacing the Remote Control Batteries
Check the positions of the (+) and (-) marks inside the battery
holder to ensure the batteries are inserted the correct way.
If delays in the responsiveness of the remote control occur or if it does not
operate after it has been used for some time, it probably means that the
batteries are becoming flat. When this happens, replace them with new
batteries. Have two spare AAA-size alkali batteries ready to use when
required.
Attention
Make sure you read the Safety Instructions/World-Wide Warranty
Terms before handling the batteries. s Safety Instructions
C Replace the battery cover.
Press the battery compartment cover until it clicks into place.
Procedure
A Remove the battery cover.
While pushing the battery compartment cover catch, lift the cover
up.
Catch
75
Replacing Consumables
Replacing the Lamp
Attention
f Lamp replacement period
It is time to replace the lamp when:
• The message "Replace the lamp.Replace the lamp." is displayed
when you start projecting.
A message is displayed.
• The lamp replacement message is set to appear after the following
time periods in order to maintain the initial brightness and quality
of the projected images. s "Brightness Control" p.43
·When used continually at high brightness: About 2400 hours
·When used continually at low brightness: About 2900 hours
• If you continue to use the lamp after the replacement period has
passed, the possibility that the lamp may explode increases. When
the lamp replacement message appears, replace the lamp with a
new one as soon as possible, even if it is still working.
• Depending on the characteristics of the lamp and the way it has
been used, the lamp may become darker or stop working before
the lamp warning message appears. You should always have a
spare lamp ready incase it is needed.
• The lamp indicator flashes orange.
f How to replace the lamp
Flashing orange
Attention
• When replacing the lamp because it has stopped illuminating,
there is a possibility that the lamp may be broken.
If replacing the lamp of a projector which has been installed on
the ceiling, you should always assume that the lamp is broken,
and you should stand to the side of the lamp cover, not underneath
it. Remove the lamp cover gently. Small pieces of glass may fall
out when the lamp cover is opened. If pieces of glass get into your
eyes or mouth, seek medical advice immediately.
• Wait until the lamp has cooled down sufficiently before removing
the lamp cover. If the lamp is still hot, burns or other injuries may
result. It takes about one hour after the power has been turned off
for the lamp to be cool enough.
• The projected image gets darker or starts to deteriorate.
76
Replacing Consumables
Procedure
you turn off the projector's power and the
A After
confirmation buzzer beeps twice, disconnect the
C Loosen the two lamp fixing screws.
power cable.
until the lamp has cooled down, then remove
B Wait
the lamp cover.
Loosen the lamp cover fixing screw with the screwdriver supplied
with the new lamp or a + head screwdriver. Then slide the lamp
cover straight forward and lift it to remove.
D Take out the old lamp.
If the lamp is cracked, replace it with a new lamp, or contact your
local dealer for further advice. If replacing the lamp yourself, be
careful to avoid pieces of broken glass.
77
Replacing Consumables
E Install the new lamp.
Insert the new lamp along the guide rail in the correct direction so
that it fits in place, push it down firmly, and once it is fully inserted
tighten the two screws.
F Replace the lamp cover.
Attention
• Make sure you install the lamp securely. If the lamp cover is
removed, the lamp turns off automatically as a safety precaution.
If the lamp or the lamp cover is not installed correctly, the lamp
does not turn on.
• This product includes a lamp component that contains mercury
(Hg). Please consult your local regulations regarding disposal or
recycling. Do not dispose of it with normal waste.
f Resetting the lamp operating time
The projector records how long the lamp is turned on and a message and
indicator notify you when it is time to replace the lamp. After replacing
the lamp, make sure you reset the lamp hours from the configuration
menu. s p.58
q
Only reset the lamp operating time after the lamp has been
replaced, otherwise the lamp replacement period is not
indicated correctly.
78
Replacing Consumables
Replacing the Air Filter
C Install the new air filter.
Slide the air filter in from the outside and push until it clicks into
place.
f Air filter replacement period
It is time to replace the air filter when:
• The air filter is ripped.
• The message is displayed even though the air filter has been
cleaned.
f How to replace the air filter
The air filter can be replaced even when the projector is suspended from a
ceiling.
Procedure
you turn off the projector's power and the
A After
confirmation buzzer beeps twice, disconnect the
power cable.
B Remove the air filter.
Put your finger into the recess of the air filter and slide it forward to
remove it.
q
Dispose of used air filters properly in accordance with your
local regulations.
Material quality of the frame section: Polycarbonate, ABS
resin
Material quality of the filter section: Polyurethane form
Saving a User’s Logo
You can save the image that is currently being projected as a user's
logo.
79
the configuration menu, select "Extended" B From
"User's Logo". s "Using the Configuration Menu"
p.40
q
Check the buttons you can use and the operations they perform in
the guide under the menu.
When a user's logo is saved, the previous user's logo is
erased.
Procedure
the image you want to use as the user's
A Project
logo, and then press the [Menu] button.
Using the remote control
Using the control panel
q
• If "User's Logo Protect" from "Password Protect" is set
to "On", a message is displayed and the user's logo
cannot be changed. You can make changes after setting
"User's Logo Protect" to "Off". s p.35
• If "User's Logo" is selected when Keystone, E-Zoom,
Resize, or Progressive are being performed, the function
currently being performed is cancelled.
"Choose this image as the User's Logo?" is
C When
displayed, select "Yes".
q
When you press the [Enter] button on the remote control or
the control panel, the screen size may change according to
the signal as it changes to the resolution of the image
signal.
80
Saving a User’s Logo
image is recorded and a selection marquee box
D The
is displayed. Move the box to select the part of the
image to use as the user's logo.
"Select this image?" is displayed, select
E When
"Yes".
the zoom factor from the zoom setting
F Select
screen.
the message "Save this image as the User's
G When
Logo?" is displayed, select "Yes".
Using the remote control
The image is saved. After the image has been saved, the message
"Completed." is displayed.
Using the control panel
q
q
You can save at up to 400 ^ 300 dots in size.
• Saving the user's logo may take about 15 seconds. Do not
use the projector or any connected equipment while it is
saving, otherwise malfunctions may occur.
• Once a user's logo has been saved, the logo cannot be
returned to the factory default.
Screen Size and Distance
81
See the following table to choose the best position for your projector. The values are only a guide.
Units: cm (in.)
4:3 Screen Size
30"
40"
50"
60"
80"
100"
120"
150"
200"
300"
61 ^ 46 (24 ^ 18)
81 ^ 61 (32 ^ 24)
100 ^ 76 (39 ^ 30)
120 ^ 90 (47 ^ 35)
160 ^ 120 (63 ^ 47)
200 ^ 150 (79 ^ 59)
240 ^ 180 (94 ^ 71)
300 ^ 230 (118 ^ 91)
410 ^ 300 (161 ^ 118)
610 ^ 460 (240 ^ 181)
Projection Distance U
Minimum Maximum
(Wide) to (Tele)
83 to 139 (33 to 55)
114 to 189 (45 to 74)
144 to 238 (57 to 94)
174 to 287 (69 to 113)
235 to 386 (93 to 152)
296 to 484 (117 to 191)
357 to 583 (141 to 229)
449 to 730 (177 to 288)
601 to 977 (237 to 385)
906 to 1469 (357 to 578)
Units: cm (in.)
16:9 Screen Size
Offset V
7 (2.6)
9 (3.4)
11 (4.3)
13 (5.1)
17 (6.9)
22 (8.6)
26 (10.3)
33 (12.9)
44 (17.1)
65 (25.7)
30"
40"
50"
60"
80"
100"
120"
150"
200"
300"
66 ^ 37 (26 ^ 15)
89 ^ 50 (35 ^ 20)
110 ^ 62 (43 ^ 24)
130 ^ 75 (51 ^ 28)
180 ^ 100 (71 ^ 39)
220 ^ 120 (87 ^ 47)
270 ^ 150 (106 ^ 59)
330 ^ 190 (130 ^ 75)
440 ^ 250 (173 ^ 98)
660 ^ 370 (260 ^ 146)
Projection Distance U
Minimum Maximum
(Wide) to (Tele)
90 to 152 (36 to 60)
124 to 205 (49 to 81)
157 to 259 (62 to 102)
190 to 313 (75 to 123)
256 to 420 (101 to 165)
323 to 527 (127 to 208)
389 to 635 (153 to 250)
489 to 796 (192 to 313)
655 to 1064 (258 to 419)
987 to 1601 (388 to 630)
Screen
90°
Offset V
1 (0.4)
1 (0.5)
1 (0.6)
2 (0.7)
2 (0.9)
3 (1.2)
4 (1.4)
4 (1.8)
6 (2.3)
9 (3.5)
Centre of
lens
Screen
90°
Centre of
lens
Connecting USB Devices (Digital Camera, Hard Disk Drive or Memory Devices) (EMP-1815 Only)
USB2.0/1.1-compatible digital cameras, hard disk drives and USB
storage devices can be connected to the projector. Image files that are
stored inside the digital camera and scenarios, images and movies
that are stored inside USB storage devices can be played back by
EasyMP CardPlayer. sEasyMP Operation Guide "PC Free Basic
Operations"
Connecting USB Devices
The following procedure describes how to connect USB devices, using a
digital camera as an example.
Connect a digital camera to the projector using a USB cable provided
with, or specified for use with your digital camera.
q
• Use a USB cable less than 3m in length. If the cable
exceeds 3m, CardPlayer may not function correctly.
• Check that there is no wireless LAN card or memory card
in the projector's card slot before connecting any USB
device.
USB cable
To [USB Type A] port
To USB port of
digital camera
Attention
• If you use a USB hub, the connection may not operate correctly.
Devices such as digital cameras and USB storage devices should
be connected to the projector directly.
• When using an USB-compatible hard disc, be sure to connect the
AC adaptor supplied with the hard disc.
82
Inserting and Ejecting CompactFlash Cards (EMP-1815 Only)
On the EMP-1815, CompactFlash cards can be used as external
memory storage.
The following explains how to insert and eject CompactFlash cards.
How to Insert Cards
Attention
• Insert CompactFlash card so that it faces the correct direction.
Inserting a card in the wrong direction may result in malfunction
or damage.
• When carrying the projector, be sure to remove the CompactFlash
card.
How to Remove Cards
Attention
When the access indicator of the card slot is lit green or is flashing,
do not remove the CompactFlash card. Doing so will damage data
stored on the card or cause the projector to malfunction.
Procedure
A Press the eject button at the side of the card slot.
The eject button springs out.
Eject button
Card slot access
indicator
Procedure
Insert the CompactFlash card into the card slot with its top
surface facing up.
Firmly insert the card as far as it can go.
CompactFlash card
(commercially available)
83
84
Inserting and Ejecting CompactFlash Cards (EMP-1815 Only)
B Press the eject button again.
The CompactFlash card is ejected from the card slot. Remove the
card from the card slot.
Attention
Be sure to push the eject button back in. If the eject button stays
out, it may become bent or damaged in other ways.
f Card Slot Access Indicator Statuses
When a CompactFlash card is inserted into the projector, the access status
of the card is indicated by the lighting status of the card slot access
indicator.
: Flashing
Indicator
Status
Flashing
: Lit:
Access Status
Lit
Data is either being read from or being written to the
CompactFlash card.
The CompactFlash card is standing by.
Off
The CompactFlash card is not performing any operations.
: Off
Connecting to External Equipment
Connecting to an External Monitor
85
Connecting to External Speakers
Computer images being input to the Computer1 port can be displayed on
an external monitor and the screen at the same time when connected to the
projector. This means that you can check projected images on an external
monitor when giving presentations even if you cannot see the screen.
Connect to an external monitor using the cable supplied with the monitor.
You can connect speakers with built-in amplifiers to the projector's Audio
Out port to enjoy a fuller quality of sound.
Connect with a commercially available audio cable (pin plug W 3.5 mm
stereo mini plug and so on). Use an audio cable compatible with the
connector on the external speakers.
To external speakers
Monitor port
Cable supplied with monitor
q
To Monitor Out port
• Component video signals and equipment connected to the
Computer2 port, Video port, and S-Video port cannot be
output to an external monitor.
• The setting gauge for Keystone, the configuration and
help screen, and so on are not output to an external
monitor.
Audio cable
(commercially available)
q
To Audio Out port
When an audio cable plug is inserted in the Audio Out port,
the audio changes to the external destination, and audio is
no longer emitted from the projector's built-in speaker.
Connecting a LAN Cable
Connect with a commercially available 100baseTX or 10baseT type
LAN cable.
To LAN port
LAN cable
(commercially available)
To LAN port
Attention
To prevent malfunctions, use a category 5 shielded LAN cable.
86
Optional Accessories and Consumables
The following list of optional accessories is current as of February,
2007. Details of accessories are subject to change without notice and
availability may vary depending on the country of purchase.
f Optional accessories
60" portable screen ELPSC07
80" portable screen ELPSC08
100" screen ELPSC10
Portable roll-type screens (Aspect ratiog 4:3)
50" portable screen ELPSC06
A compact screen that can be carried easily. (Aspect ratio 4:3)
HD-15 cable ELPKC02
(1.8 m - for mini D-Sub15-pin/mini D-Sub 15pin)
This is the same as the computer cable supplied with the projector.
HD-15 cable ELPKC09
(3 m - for mini D-Sub15-pin/mini D-Sub 15pin)
HD-15 PC cable ELPKC10
(20 m - for mini D-Sub15-pin/mini D-Sub 15pin)
Use one of these longer cables if the computer cable supplied with the projector is
too short.
Component video cable ELPKC19
(3 m - for mini D-Sub 15-pin/RCA male^3)
Use to connect a component videog source
Ceiling plate* ELPFC03
Ceiling pipe (370 mm (14.57 in.)/silver)* ELPFP04
Ceiling pipe (570 mm (22.44 in.)/silver)* ELPFP05
Ceiling pipe (770 mm (30.31 in.)/silver)* ELPFP06
Use when installing the projector on a high ceiling.
Ceiling mount* ELPMB18
Use when installing the projector on a ceiling.
* A special method of installation is required to suspend the projector from a
ceiling. Contact your dealer or the nearest address provided in the World-Wide
Warranty Terms if you want to use this installation method. s Inquiries
f Consumables
Lamp unit ELPLP40
Use as a replacement for used lamps.
Air filter (by 2) ELPAF08
Use as a replacement for used air filters.
87
Glossary
88
This section explains easily terms that are used with the projector and difficult terms that are not explained in the text of this guide. For details,
refer to other commercially available publications.
Aspect ratio
Component video
Composite video
Contrast
DHCP
Dolby Digital
ESSID
Gateway address
HDTV
Interlace
IP address
Progressive
Refresh rate
SDTV
SNMP
SNMP Trap IP address
The ratio between an image's length and its height. HDTV images have an aspect ratio of 16:9 and appear elongated. The aspect ratio for
standard images is 4:3.
A video signal which has the luminance component and colour component separated to provide better image quality.
Refers to images that consist of three independent signals: Y (luminance signal), Pb and Pr (colour difference signals).
Video signals that have the video brightness signals and colour signals mixed together. The type of signals commonly used by household
video equipment (NTSC, PAL, and SECAM formats). The carrier signal Y (luminance signal) and chroma (colour) signal that are
contained in the colour bar are overlapped to form a single signal.
The relative brightness of the light and dark areas of an image can be increased or decreased to make text and graphics stand out more
clearly, or to make them appear softer. Adjusting this particular property of an image is called "contrast adjustment".
An abbreviation of Dynamic Host Configuration Protocol, this protocol automatically assigns an IP addressg to equipment connected to
a network.
A sound format developed by Dolby Laboratories. Normal stereo is a 2-channel format that uses two speakers. Dolby Digital is a 6channel (5.1-channel) system which adds to this a centre speaker, two rear speakers, and a sub-woofer.
ESS is an abbreviation of Extended Service Set (enhanced service set). ESSID is an identification number for connecting with a
counterpart on a wireless LAN. Wireless communication is possible between devices that correspond to ESSID.
This is a server (router) for communicating across a network (subnet) divided according to subnet masksg.
An abbreviation for High-Definition Television that refers to high-definition systems which satisfy the following conditions.
• Vertical resolution of 750p or 1125i or greater (p = progressiveg, i = interlaceg)
• Screen aspect ratiog of 16:9
• Dolby Digitalg audio reception and playback (or output)
A method of image scanning whereby the image data is divided into fine horizontal lines that are displayed in sequence starting from left
to right and then from top to bottom. The even-numbered lines and odd-numbered lines are displayed alternately.
A number to identify a computer connected to a network.
A method of image scanning whereby the image data from a single image is scanned sequentially from top to bottom to create a single
image.
The light-emitting element of a display maintains the same luminosity and colour for an extremely short time. Because of this, the image
must be scanned many times per second to refresh the light-emitting element. The number of refresh operations per second is called the
Refresh rate and is expressed in hertz (Hz).
An abbreviation for Standard Definition Television that refers to standard television systems which do not satisfy the conditions for
HDTVg High-Definition Television.
An abbreviation for Simple Network Management Protocol, which is the protocol for monitoring and controlling devices such as routers
and computers connected to a TCP/IP network.
This is the IP addressg for the destination computer used for error notification in SNMP
Glossary
Squeeze mode
sRGB
Subnet mask
SVGA
S-video
SXGA
Synchronization
Tracking
VGA
XGA
89
In this mode, wide-screen images in 16:9 mode are compressed in the horizontal direction so that they are stored on the recording
medium as 4:3 images.
When these images are played back by the projector in squeeze mode, they are restored to their original 16:9 format.
An international standard for colour intervals that was formulated so that colours that are reproduced by video equipment can be handled
easily by computer operating systems (OS) and the Internet. If the connected source has an sRGB mode, set both the projector and the
connected signal source to sRGB.
This is a numerical value that defines the number of bits used for the network address on a divided network (subnet) from the IP address.
A type of video signal with a resolution of 800 (horizontal) ^ 600 (vertical) dots that is used by IBM PC/AT-compatible computers.
A video signal which has the luminance component and colour component separated to provide better image quality.
Refers to images that consist of two independent signals: Y (luminance signal) and C (colour signal).
A type of video signal with a resolution of 1280 (horizontal) ^ 1024 (vertical) dots that is used by IBM PC/AT-compatible computers.
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting
images are not of a good quality. The process of matching the phases of these signals (the relative position of the crests and the troughs in
the signal) is called Synchronization. If the signals are not synchronized, flickering, blurriness, and horizontal interference occur.
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting
images are not of a good quality. The process of matching the frequency of these signals (the number of crests in the signal) is called
Tracking. If tracking is not carried out correctly, wide vertical stripes appear in the signal.
A type of video signal with a resolution of 640 (horizontal) ^ 480 (vertical) dots that is used by IBM PC/AT-compatible computers.
A type of video signal with a resolution of 1024 (horizontal) ^ 768 (vertical) dots that is used by IBM PC/AT-compatible computers.
ESC/VP21 Commands
90
Command List
Cable Layouts
When the power ON command is transmitted to the projector, the power
turns on and it enters warm-up mode. When the projector's power has
turned on, a colon ":" (3Ah) is returned.
When a command is input, the projector executes the command and
returns a ":", and then accepts the next command.
If the command being processed terminates abnormally, an error message
is output and a ":" is returned.
Item
Power ON/OFF
ON
OFF
Signal selection
Video
S-Video
EasyMP (EMP-1815
only)
A/V Mute ON/OFF ON
OFF
A/V Mute selection Black
Blue
Logo
Item
Signal selection
Computer (Auto)
Computer
Component Video
f Serial connection
• Connector shape:
D-Sub 9-pin (male)
• Projector input connector: RS-232C
<At the projector>
<At the computer>
Command
PWR ON
PWR OFF
SOURCE 41
SOURCE 42
SOURCE 50
MUTE ON
MUTE OFF
MSEL 00
MSEL 01
MSEL 02
Command
Computer1
Computer2
Port
Port
SOURCE 1F
SOURCE 2F
SOURCE 11
SOURCE 21
SOURCE 14
SOURCE 24
* Add a Carriage Return (CR) code (0Dh) to the end of each command and
transmit.
<At the projector>
GND
RD
TD
DTR
DSR
(PC serial cable)
5
2
3
4
6
<At the computer>
5
3
2
6
4
GND
TD
RD
DSR
DTR
Signal
GND
TD
RD
DSR
DTR
Function
Signal wire ground
Transmit data
Receive data
Data set ready
Data terminal ready
PJLink (EMP-1815 Only)
91
PJLink Class 1 was established by the JBMIA (Japan Business
Machine and Information System Industries Association) as a standard
protocol for controlling network-compatible projector's as part of their
efforts to standardize projector control protocols.
The projector complies with the PJLink Class 1 standard established
by the JBMIA.
It complies with all commands except for the following commands
defined by PJLink Class 1, and agreement was confirmed by the
PJLink standard adaptability verification.
Non-compatible commands
Mute settings
Function
Image muting set
Image muting cancel
Audio muting set
Audio muting cancel
PJLink Command
AVMT 11
AVMT 10
AVMT 21
AVMT 20
Input names defined by PJLink and corresponding projector
connectors
Input Connector
Computer1 input
Computer2 input
Video input
S-Video input
PJLink Command
INPT 11
INPT 12
INPT 21
INPT 22
Manufacturer name displayed for "Manufacture name information
query"
EPSON
Model name displayed for "Product name information query"
EMP-1815
List of Supported Monitor Displays
f Computer image
Signal
VGAEGA
VGAg
SVGAg
XGAg
SXGAg
SXGA
SXGA
UXGA
MAC13"
MAC16"
MAC19"
MAC19"
MAC21"
SDTVg (525i)
SDTV (625i)
SDTV (525p)
SDTV (625p)
HDTVg (750p)
HDTV (1125i)
92
f Component video
Refresh Rateg
(Hz)
*
60/72/75/85, iMac
56/60/72/75/85, iMac*
60/70/75/85, iMac*
70/75/85
60/75/85
60/75/85
60
60
60
50
60
50
50/60
50/60
Resolution
(dots)
640 ^ 350
640 ^ 480
800 ^ 600
1024 ^ 768
1152 ^ 864
1280 ^ 960
1280 ^ 1024
1600 ^ 1200
640 ^ 480
832 ^ 624
1024 ^ 768
1024 ^ 768
1152 ^ 870
720 ^ 480
720 ^ 576
720 ^ 480
720 ^ 576
1280 ^ 720
1920 ^ 1080
Number of
Pixels Used
When Display
is Resized
(dots)
1024 ^ 560
1024 ^ 768
1024 ^ 768
1024 ^ 768
1024 ^ 768
1024 ^ 768
960 ^ 768
1024 ^ 768
1024 ^ 768
1024 ^ 768
1024 ^ 768
1024 ^ 768
1016 ^ 768
1024 ^ 768
1024 ^ 768
1024 ^ 768
1024 ^ 768
1024 ^ 576
1024 ^ 576
* Connection is not possible if the equipment does not have a VGA output port.
Even when signals other than those mentioned above are input, it is likely that
the image can be projected. However, not all functions may be supported.
Signal
SDTVg (525i)
SDTV (625i)
SDTV (525p)
SDTV (625p)
HDTVg (750p)
16:9
HDTV (1125i)
16:9
Refresh Rateg
(Hz)
60
50
60
50
Resolutions (dots)
Aspect Ratiog Aspect Ratio
4:3
16:9
1024 ^ 768
1024 ^ 576
1024 ^ 768
1024 ^ 576
1024 ^ 768
1024 ^ 576
1024 ^ 768
1024 ^ 576
50/60
1024 ^ 768
1024 ^ 576
50/60
1024 ^ 768
1024 ^ 576
f Composite video/S-video
Signal
TV (NTSC)
TV
(PAL, SECAM)
Refresh Rateg
(Hz)
60
50
Resolutions (dots)
Aspect Ratiog Aspect Ratio
4:3
16:9
1024 ^ 768
1024 ^ 576
1024 ^ 768
1024 ^ 576
Specifications
Product name
Dimensions
Panel size
Display method
Resolution
Focus adjustment
Zoom adjustment
Lamp
Max. audio output
Speaker
Power supply
Power consumption
100 to 120 V area
200 to 240 V area
Operating altitude
Operating temperature
Storage temperature
Mass
93
Multimedia Projector
Multimedia Projector
EMP-1815
EMP-1810
345 (W) ^ 86 (H) ^ 257 (D) mm (not including protruding parts)
0.8"
Polysilicon TFT active matrix
786,432 pixels XGAg (1024 (W) ^ 768 (H) dots) ^ 3
Manual
Manual (1 to 1.6)
UHE lamp, 210 W, Model No.: ELPLP40
5 W monaural
1
100 to 200 V AC ±10%, 50/60 Hz 3.4 to 1.5 A
Operating: 306 W
Standby power consumption (network invalid): 2.6 W
Standby power consumption (network valid): 12 W
Operating: 286 W
Standby power consumption (network invalid): 4.6 W
Standby power consumption (network valid): 12 W
Altitude 0 to 2286 m (0 to 7500 ft)
5 to 35°C (No condensation)
-10 to +60°C (No condensation)
Approx 3.1 kg
Approx 2.9 kg
Pixelworks DNXTM ICs
are used in this projector.
Angle of tilt
0° to 45°
0° to 45°
If you use the projector tilted at an angle of
more than 45° it could be damaged and cause
an accident.
94
Specifications
Connectors Computer1 input port
Audio1 input port
Computer2 input port
Audio2 input port
S-Video input port
Video input port
Audio-L/R input port
Monitor Out port
Audio Out port
RS-232C port
LAN port
USB port (Type A)*
USB port (Type B)*
USB port (exclusive wireless
LAN unit)
Card slot
1
1
1
1
1
1
1
1
1
1
1
1
Mini D-Sub15-pin (female) blue
Stereo mini jack
Mini D-Sub15-pin (female) blue
Stereo mini jack
Mini DIN 4-pin
RCA pin jack
RCA pin jack
Mini D-Sub15-pin (female) black
Stereo mini jack
Mini D-Sub 9-pin (male)
RJ45
USB connector (Type A)
-
1
USB connector (Type B)
USB connector (Type B)
USB connector (Type A)
-
CompactFlash card
-
1
1
* This supports USB2.0.
USB ports are not guaranteed to operate all devices that support USB.
Other detailed specifications, please access your location (country/area) from Epson homepage, http://www.epson.com
Specifications
Safety standards
USA: UL60950-1
Canada: CSA C22.2 No.60950-1
EU: The Low Voltage Directive
(73/23/EEC)
IEC/EN60950-1
This product is also designed for IT power distribution system with
phase-to-phase voltage 230V.
EMC standards
USA: FCC Part 15B Class B (DoC)
Canada: ICES-003 Class B
EU: The EMC Directive
(89/336/EEC)
EN55022, Class B
EN55024
IEC/EN61000-3-2
IEC/EN61000-3-3
Australia/New Zealand: AS/NZS CISPR 22:2002 Class B
95
96
Specifications
DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B
Personal Computers
We:
Located at:
Tel:
Epson America, Inc.
3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
562-290-5254
Declare under sole responsibility that the product identified herein,
complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital
device. Each product marketed, is identical to the representative unit
tested and found to be compliant with the standards. Records maintained
continue to reflect the equipment being produced can be expected to be
within the variation accepted, due to quantity production and testing on a
statistical basis as required by 47CFR 2.909. Operation is subject to the
following two conditions :
Trade Name:
EPSON
Type of Product:
Projector
Model:
EMP-1815/1810
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause interference to radio and television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this
equipment will invalidate the FCC Certification or Declaration of this device
and may cause interference levels which exceed the limits established by the
FCC for this equipment. It is the responsibility of the user to obtain and use a
shielded equipment interface cable with this device. If this equipment has
more than one interface connector, do not leave cables connected to unused
interfaces. Changes or modifications not expressly approved by the
manufacturer could void the userís authority to operate the equipment.
FCC Radiation Exposure Statement:
The wireless LAN 802.11a/b/g adapter Model: WN6501CEP complies with
FCC radiation exposure limits set forth for an uncontrolled environment. This
device should be installed and operated with minimum distance 20 cm
between the radiator and your body.
Appearance
97
3-M4^9
Centre of lens
98.0
12
86.0
47.1*
4.8
8.8
257.0
92.0
90.0
345.0
* Distance from centre of lens to suspension bracket fixing point
115.0
127.0
53.0
Units: mm
Index
98
A
Cross ...................................................................27
A/V mute ............................................................. 23
A/V mute slide ....................................................... 7
Abs. Color Temp. ................................................ 41
Air exhaust vent .................................................... 7
Air filter .................................................................. 9
Air filter replacement period ................................ 78
Air intake vent ....................................................... 9
Angle of tilt .......................................................... 93
Aspect ratio ......................................................... 25
Audio Out port ..................................................... 10
Audio-L/R input port ............................................ 10
Auto setup ........................................................... 42
D
K
E
Keystone ............................................................. 43
Email Address 1/2/3 setting .................................55
ESC/VP21 ...........................................................90
ESSID ..................................................................49
Extended menu ...................................................44
External dimension diagram ................................97
External monitor ..................................................85
External speakers ................................................85
E-zoom ................................................................27
L
Lamp cover ........................................................... 7
Lamp hours ......................................................... 57
Lamp indicator .................................................... 61
Lamp replacement period ................................... 75
LAN port .............................................................. 10
Language ............................................................ 45
Low brightness .................................................... 43
F
C
Ceiling ................................................................. 44
Cleaning the air filter and air intake vent ............. 73
Cleaning the projector's surface .......................... 73
Color adjustment ................................................. 41
Color mode .................................................... 22, 41
Color saturation ................................................... 41
Computer1 Input ................................................. 42
Computer1 input port .......................................... 10
Computer2 Input ................................................. 42
Computer2 input port .......................................... 11
Configuration menu ............................................. 40
Connecting a LAN Cable ..................................... 86
Connecting USB Devices .................................... 82
Consumables ...................................................... 87
Contrast ............................................................... 41
Control panel ....................................................... 12
Image menu ........................................................ 41
Indicators ............................................................ 61
Info menu ............................................................ 57
Input signal .......................................................... 57
IP address ..................................................... 49, 54
DHCP ..................................................................49
Direct power on ...................................................45
Display .................................................................44
Display background .............................................44
B
Basic Menu ......................................................... 48
Blackboard .......................................................... 22
Brightness ........................................................... 41
Brightness control ............................................... 43
I
Focus ring ..............................................................7
Freeze .................................................................24
Front ....................................................................44
Front adjustable feet ..............................................7
Full Lock ..............................................................37
M
Mail Menu ........................................................... 55
Mail Notification ................................................... 55
Menu ................................................................... 40
Messages ............................................................ 44
Monitor Out port .................................................. 10
Mouse pointer ..................................................... 28
Multi-Screen Colour Adjustment ......................... 32
G
Gateway address ...........................................49, 54
Glossary ..............................................................88
N
H
HDTV ...................................................................92
Help function ........................................................60
High altitude mode: ..............................................45
How to replace the air filter ..................................78
How to replace the lamp ......................................75
Network Menu ..................................................... 46
Network Protect .................................................. 35
Numeric buttons ............................................ 13, 14
99
Index
O
Replacing batteries ..............................................74
Request code ......................................................36
Reset all ...............................................................58
Reset menu .........................................................58
Resetting the lamp operating time .................58, 77
Resize ..................................................................92
Resize display .....................................................92
Resolution ......................................................57, 92
RS-232C port .......................................................10
Operating temperature ........................................ 93
Operation ............................................................ 45
Operation lock ............................................... 37, 43
Optional accessories ........................................... 87
Overheating ......................................................... 62
P
Part names and functions ..................................... 7
Password protect ................................................ 34
Password protect sticker ..................................... 35
Photo ................................................................... 22
PJLink ................................................................. 91
Pointer ................................................................. 26
Pointer shape ...................................................... 43
Port number ........................................................ 55
Position ............................................................... 42
Power indicator ................................................... 61
Power inlet .......................................................... 10
Power on protect ................................................. 34
Presentation ........................................................ 22
Problem solving ................................................... 61
Progressive ......................................................... 42
Projection ............................................................ 44
Projection distance .............................................. 81
Projector ID ......................................................... 30
Projector name .................................................... 48
R
Rear .................................................................... 44
Rear foot ............................................................... 9
Rear screen ......................................................... 72
Refresh rate ........................................................ 57
Remote control .............................................. 13, 28
Remote Control ID .............................................. 31
Remote control light-emitting area ...................... 14
Remote receiver .............................................. 7, 10
T
Temp indicator .................................................... 61
Theatre ................................................................ 22
Tint ...................................................................... 41
Top menu ............................................................ 40
Tracking .............................................................. 42
U
S
Screen size ..........................................................81
Security Menu ......................................................50
Security slot .........................................................10
Settings menu ......................................................43
Sharpness ...........................................................41
Signal menu .........................................................42
Sleep mode .........................................................45
SMTP server ........................................................55
SNMP Menu ........................................................56
SNMP Trap IP address ........................................56
Software keyboard ...............................................47
Source .................................................................57
Source search .........................................12, 13, 20
Speaker ...........................................................7, 85
Specifications ......................................................93
Sports ..................................................................22
sRGB ...................................................................22
Standby mode .....................................................45
Startup screen .....................................................44
Storage temperature ............................................93
Sub menu ............................................................40
Subnet mask ..................................................49, 54
Supported monitor displays .................................92
Suspension bracket fixing points .....................9, 97
S-video port .........................................................10
Sync info ..............................................................57
Synchronization ...................................................42
USB port ............................................................. 10
User's logo .......................................................... 79
User's logo protect .............................................. 34
V
Video port ............................................................ 10
Video signal .................................................. 42, 57
Volume ................................................................ 43
W
Wide-screen projection ....................................... 25
Wired LAN Menu ................................................. 54
Wireless LAN Menu ............................................ 49
Wireless mouse .................................................. 28
Z
Zoom ring .............................................................. 7
100
All rights reserved. No part of this publication may be reproduced, stored
in a retrieval system, or transmitted in any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise, without the
prior written permission of Seiko Epson Corporation. No patent liability is
assumed with respect to the use of the information contained herein.
Neither is any liability assumed for damages resulting from the use of the
information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the
purchaser of this product or third parties for damages, losses, costs, or
expenses incurred by the purchaser or third parties as a result of: accident,
misuse, or abuse of this product or unauthorized modifications, repairs, or
alterations to this product, or (excluding the U.S.) failure to strictly
comply with Seiko Epson Corporation's operating and maintenance
instructions.
General Notice:
Macintosh, Mac, and iMac are registered trademarks of Apple Computer,
Inc.
IBM is a registered trademark of International Business Machines
Corporation.
Windows, Windows NT, and PowerPoint are either registered trademarks
or trademarks of Microsoft Corporation in the U.S and/or other countries.
Dolby is a trademark of Dolby Laboratories.
Pixelworks and DNX are trademarks of Pixelworks, Inc.
CompactFlash is a registered trademark or trademark of Sandisk
Corporation.
Other product names used herein are also for identification purposes only
and may be trademarks of their respective owners. Epson disclaims any
and all rights in those marks.
This product uses open source software.
Seiko Epson Corporation shall not be liable against any damages or
problems arising from the use of any options or any consumable products
other than those designated as Original Epson Products or Epson
Approved Products by Seiko Epson Corporation.
The contents of this guide may be changed or updated without further
notice.
Illustrations in this guide and the actual projector may differ.
ZSEIKO EPSON CORPORATION 2007. All rights reserved.
Download PDF

advertising