Sam4s | GIANT-100 | User guide | Sam4s GIANT-100 User guide

Sam4s GIANT-100 User guide
GIANT-100
Receipt Printer
User Guide
All specifications are subject to change without notice.
Warning - U.S.
This equipment has been tested and founded to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
In case, Operation of this equipment in a residential area is likely to cause harmful
interference to radio communications. the user will be required to correct the
interference at his own expense.
Notice - Canada
This Apparatus complies with class “A” limits for radio interference as specified in the
Canadian department of communications radio interference regulations.
Get appareil est conforme aux normes class “A” d’interference radio tel que specifier
par ministre canadien des communications dans les reglements d’interference radio.
Warning
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
FCC compliance Information(for WLAN and BLUETOOTH)
This device complies with part 15 of FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) This
device must accept any interference received, including interference that may cause
undesired operation.
Information to the user
NOTES : This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
OPERATOR’S Manual
3
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
[IMPORTANT NOTE]
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20centimeters between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Caution
Some semiconductor devices are easily damaged by static electricity. You should turn
the printer “OFF”, before you connect or remove the cables on the rear side, in order
to guard the printer against the static electricity. If the printer is damaged by the static
electricity, you should turn the printer “OFF” and contact your dealer for assistance.
INTRODUCTION
The GIATN-100 Roll Printer is designed for use with electronic instruments such as
system ECR, POS, banking equipment, computer peripheral equipment, etc.
The main features of the printer are as follows:
1. High speed printing : 250mm/s, 59 lines per second(12X24 Font)
2. Low noise thermal printing.
3. Support a variety of interfaces : USB default / USB+RS-232(Serial) / USB+WLAN
USB+ETHERNET+RS-233(Serial)
4. Jam free (Implementation of automatic return of Cutter Jam)
5. Characters can be scaled up to 64 times compared to it’s original size.
4
GIANT-100 Receipt Printer
6. The data buffer allows the unit to receive print data even during printing.
7. Bar code printing is possible by using a bar code command.
8. Different print densities can be selected by DIP switches.
9. Peripheral units drive circuit enables control of external devices such as cash
drawer.
10. 2-dimantional bar code(PDF-417) and Two color printing.
Please be sure to read the instruction in this manual carefully before using GIANT-100.
NOTES : The Power outlet shall be near the equipment and it should be easily accessible.
LEGISLATION AND WEEE SYMBOL
2002/96/CE Waste Electrical and Electronic Equipment Directive on the treatment, collection,
recycling and disposal of electric and electronic devices and their components.
The crossed dustbin symbol on the device means that it should not be disposed of
with other household wastes at the end of its working life. Instead, the device should
be taken to the waste collection centres for activation of the treatment, collection,
recycling and disposal procedure.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can take
item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
OPERATOR’S Manual
5
Contents
Chapter 1. Setting Up the Printer··························· 7
1.1. Unpacking······································································7
1.2. Connecting the Cables·················································7
1.3. Connecting the host device·········································8
1.4. Connecting the Drawer················································8
1.5. Connecting the Power Supply····································9
1.6. Installing options & Replacing the Paper Roll········10
1.6.1. Partition Installation············································· 10
1.6.2. Wall Mount Installation······································· 11
1.6.3. Splash Cover Installation···································· 12
1.6.4. Paper Roll Installation········································· 12
1.7. Adjustments and Settings ·········································13
1.7.1. Serial Interface(RS-232C) DIP Switch Set············· 14
1.7.2. WLAN Interface DIP Switch Set··························· 15
1.7.3. Serial+Ethernet Interface DIP Switch Set············· 15
1.8. Using the Printer ························································16
1.8.1. Control Panel (LED)············································· 16
1.8.2. Feed Button
···················································· 16
1.8.3. Panel lights : LED················································ 16
CHAPTER 2. APPENDIX······································ 17
2.1. Adjusting the Paper Near-End Sensor Location ····17
2.2. Printer Head Cleaning ···············································18
2.3. Error Status and Error Resolution ···························19
2.4. Specification·······························································20
2.4.1. General Printer specification······························· 20
2.4.2. Paper specification·············································· 20
1
Setting Up the
Printer
1.1. Unpacking
Your printer box should include these items. If any items are damaged or
missing, please contact your dealer for assistance.
Interface cable(option)
Power-cord
Roll paper
GIANT-100
Receipt Printer
User Guide
All specifications are subject to change without notice.
GIANT-100
Wall Mount(option)
AC Adapter
Operator’s
Manual(option)
1.2. Connecting the Cables
You can connect up to three cables to the printer. They are all connected to
the connector panel on the back of the printer, which is shown as below:
Power supply
connector
Drawer Kick-out
connector
Interface connector
USB
connector
NOTES : Before connection any of the cables make sure the both the printer and
connecting device are turned off.
OPERATOR’S Manual
7
CHAPTER 1
CHAPTER
1.3. Connecting the host device
You need the appropriate interface cable.
1. Plug the cable connector securely into the printer’s interface connector.
2. Tighten the screws on both sides of the cable connector.
3. Attach the other end of the cable to the host device.
1.4. Connecting the Drawer
WARNING : Use a drawer that matches the printer specification.
Using an improper drawer may damage the drawer as well as the printer.
CAUTION : Do not connect a telephone line to the drawer kick-out connector;
otherwise the printer and the telephone line may be damaged. Plug the drawer cable
into the drawer kick out connector on the back of the printer next to the power supply
connector.
To use the drawer, you can
connect the cable to the
connector.
8
GIANT-100 Receipt Printer
WARNING : Make sure that you use the power supply provided with the printer or
equivalent.
CAUTION : When connecting or disconnecting the power supply from the printer,
make sure that the power supply is not plugged into an electrical outlet. Otherwise
you may damage the power supply or the printer.
If the power supply’s rated voltage and your outlet’s voltage do not match, contact
your dealer for assistance. Do not plug in the power cord. Otherwise, you may
damage the power supply or the printer.
1. Make sure the printer is turned off.
2. Plug the DC cord connector into the power jack on the printer. If it is
necessary to connect the interface and the drawer, plug that connector
into the port on the printer. And clean up the cables.
➊
➋
UP
➌
➍
NOTES : To remove the DC cable connector, make sure the power supply’s power cord
is unplugged and then grasp the connector at the arrow and pull it straight out.
OPERATOR’S Manual
9
CHAPTER 1
1.5. Connecting the Power Supply
1.6. Installing options & Replacing the Paper Roll
1.6.1. Partition Installation
You can install the partition for 58mm paper printing on printer.
1. Push the Open-Button and open the Cover-Open.
2. Remove the partition as indicated in picture 4 below.
3. Insert the partition into the slot for 58mm wide roll as indicated in 5 & 6 below.
➊
➋
open
10
➌
➍
➎
➏
GIANT-100 Receipt Printer
1. Use the template for Wall Mounting and mark the wall where you want
to install the printer.
2. Drill 3 holes in the marked places (diameter 6.5mm depth 35mm). Insert
the wall plug (A) into the hole.
3. Insert the screws into the wall plugs as in picture 3.
4. Assemble the wall mount bracket on the bottom of the printer using
the screws.
5. Place the printer according to the screw head located on the anchor
and fit it on the wall by sliding down.
➊
➋
ⓐ
ⓑ
44mm
108mm
➌
➍
➎
OPERATOR’S Manual
11
CHAPTER 1
1.6.2. Wall Mount Installation
1.6.3. Splash Cover Installation
Insert the Splash cover boss(2point) into the Case lower.
1.6.4. Paper Roll Installation
NOTES : Be sure to use paper rolls that meet the specifications. Do not use paper
rolls that have the paper end glued to the core.
1. Open the paper roll cover by pressing the cover-open button.
➊
➋
NOTES : To avoid printer damage, do not open the printer cover during printing.
2. Remove the used paper roll core if there is one.
3. Insert the paper roll as shown.
4. Pull out a small amount of paper, as shown. Then close the cover. Tear
off the paper as shown.
12
GIANT-100 Receipt Printer
➋
CHAPTER 1
➊
NOTES : When closing the printer cover press firmly in the centre of the printer cover.
1.7. Adjustments and Settings
GIANT-100 is set up at the factory to be appropriate for most users. It does,
however, offer some settings for users with special requirements.
DIP switches that allow you to change communication settings, such as
handshaking and parity check, as well as printing density.
GIANT-100 has a near-end sensor for the paper. This can give you a warning
when the paper is almost out.
<The function is not supported when used as Wall-Mount type.>
ON
DIP SW1
1 2 3 4 5 6 7 8
ON
DIP SW2
1 2 3 4 5 6 7 8
OPERATOR’S Manual
13
1.7.1. Serial Interface(RS-232C) DIP Switch Set
•
DIP Switch Set 1 Functions
S/W
1
2
3
4
5
6
7
8
FUNCTION
Handshaking
Word Length
Parity Check
Parity Selection
Baud rate
selection
USB Mode
ON
XON/XOFF
7Bit
Yes
EVEN
OFF
DSR/DTR
8Bit
No
ODD
* Refer to the Following Table
VCOM
USB
DEFAULT
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
» Baud rate selection
Transmission speed
2400 baud
4800 baud
9600 baud
14400 baud
19200 baud
38400 baud
57600 baud
115200 baud
•
SW - 5
ON
ON
ON
ON
OFF
OFF
OFF
OFF
SW - 6
ON
ON
OFF
OFF
ON
ON
OFF
OFF
SW - 7
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Remark
-
OFF
EPSON
Disable
Enable
Self-Test Mode
DEFAULT
OFF
OFF
OFF
OFF
OFF
OFF
OFF
-
DIP Switch Set 2 Functions
S/W
1
2
3
4
5
6
7
8
FUNCTION
Emulation
* Kitchen Bell
Auto Cutter
Self-Test Mode
Select Print
Density
Download Mode
Auto Cutter Tuning
ON
STAR
Enable
Disable
Hex Dump
* Refer to the Following Table
Memory Stick
-
Interface
-
※ Kitchen Bell is option.
» Print Density
Print Density
1(Light)
2
3
4(Dark)
14
GIANT-100 Receipt Printer
SW-5
ON
OFF
ON
OFF
SW-6
ON
OFF
OFF
ON
Remark
Default
-
•
DIP Switch Set 1 Functions
S/W
1
2
3
4
5
6
7
8
•
FUNCTION
WLAN
No
No
No
No
No
No
USB Mode
ON
Disable
VCOM
OFF
Enable
USB
DEFAULT
OFF
OFF
DIP Switch Set 2 Functions
※ Dip Switch 2 Functions are the same as the series interface.
1.7.3. Serial+Ethernet Interface DIP Switch Set
•
DIP Switch Set 1 Functions
※ Dip Switch 1 Functions are the same as the series interface.
•
DIP Switch Set 2 Functions
S/W
1
2
3
4
5
6
7
8
FUNCTION
Emulation
* Kitchen Bell
Auto Cutter
Self-Test Mode
Select Print
Density
Download Mode
Communication
Mode
ON
STAR
Enable
Disable
Hex Dump
OFF
EPSON
Disable
Enable
Self-Test Mode
Memory Stick
Interface
DEFAULT
OFF
OFF
OFF
OFF
OFF
OFF
OFF
RS-232
ETHERNET
OFF
* Refer to the page 14 Table
※ Kitchen Bell is option.
OPERATOR’S Manual
15
CHAPTER 1
1.7.2. WLAN lnterface DIP Switch Set
1.8. Using the Printer
1.8.1. Control Panel (LED)
1.8.2. Feed Button
Press the FEED button once to advance paper one line. You can also hold
down the FEED button to feed paper continuously.
The button can be disabled by the ESC c 5 command.
1.8.3. Panel lights : LED
•
POWER LED
The POWER light is "ON" whenever the printer is "ON".
•
ERROR LED
This indicates an error. See 2-3 Error Status and Error Resolution <Page 17> for
information of what to do when this light comes on.
16
GIANT-100 Receipt Printer
CHAPTER
APPENDIX
2.1. Adjusting the Paper Near-End Sensor Location
The sensor has five sensitivity
settings.
1. Push the open button and
open the printer cover.
2. If you find there is too
much paper remaining
when the sensor is
triggered, set the near end
sensor to position #4 or #5.
3. Decrease the setting if the
paper runs out before the
sensor is triggered.
The accuracy of the Near-End sensor depends on the adjustment scale
setting and the winding core diameter of the roll paper. The Near-End sensor
is set at adjustment #3. This is the appropriate scale for the recommended
paper thickness.
The factory default setting is at position #3.
NOTES : Paper core diameter varies by paper manufacturer.
OPERATOR’S Manual
17
CHAPTER 2
2
2.2. Printer Head Cleaning
Paper dust on the heating elements may lower the printing quality. In this
case, clean the printer head as follows:
NOTES : Before cleaning the inside of printer or the head, make sure the power is off.
1. Power off the printer.
2. Open the printer cover.
3. Clean the thermal elements
of the printer head using
a cotton swab moistened
with alcohol solvent
(ethanol, methanol, IPA)
4. Insert a paper roll and
close the printer cover.
18
GIANT-100 Receipt Printer
2.3. Error Status and Error Resolution
The printer buzzer sounds momentarily or continuously and the ERROR LED
blinks when the printer indicates an Error status.
CHAPTER 2
Error Status Indicators include:
•
Cutter Jam
If buzzer and ERROR LED beeps
or blinks as like:
“Beep Beep---, Beep Beep---" the
printer is on Cutter Jam error status.
» Solution
While the printer is turned on
(the Power LED Is on,) press
the cover button and open the
cover. At this time, the cutter will
automatically reset.
•
Cutter Not Home
If the cutter blade is not in
home position when the normal
waiting time, the printer enters
Cutter Not Home error status.
The buzzer and ERROR LED beeps
and blinks as like:
"Beep Beep Beep----, Beep Beep
Beep----"
» Solution
Solved in the same way as the
cutter Jam error.
•
Paper Out Error
The buzzer and ERROR LED beeps
and blinks as like:
“ Beep---,Beep---” When you press
the open button to open the printer
cover, the buzzer will stop. After
this, you may change the paper roll
and continue using the printer.
open
OPERATOR’S Manual
19
2.4. Specification
2.4.1. General Printer specification
Printing method
Thermal line printing
Dot density
180dpi
Printing width
72mm
Paper width
80mm
Characters per line(default)
42/21(Font A)
56/28(Font B)
Printing speed
59 lines/sec
250mm/sec
Receive buffer size
Max 64kbytes
NOTE : Printing speed may be slower, depending on the data transmission speed
and the combination of control commands.
Supply voltage
Environmental
conditions
Lifespan
Input voltage
100 ~ 240V AC
Frequency
50 ~ 60 Hz
Output voltage
+24V DC
Temperature
5 ~ 45°C(Operating)
-10 ~ 50°C(Storage)
Humidity
10 ~ 90% RH; except the paper roll.
Printer Mechanism(MCBF)
70,000,000 lines
TPH
1×10 Pulse (150km)
Auto Cutter
1,500,000 Cut
8
2.4.2. Paper specification
Item
Paper Type
Description
Remark
Hansol HPK-110
Black color
Mitsubishi PB670
Red/Black color
Mitsubishi PB770
Blue/Black color
Paper Form
Paper Roll
Paper Width
80(+0,-1), 3.14n(+0,-0.039")
Paper Roll Size
Max 83mm
Spool Outside Dia
18mm(0.71")
The Following paper can be used instead of the specified paper above.
• TF50KS-E : Nippon Paper industries Co., Ltd.
• PD 160R : New Oji Paper Mfg, Co.,Ltd.
• F380 : Kansaki Specialty Papers,Inc.(USA)
※ Mitsubishi PB670 / PB770 are two color mode papers.
20
GIANT-100 Receipt Printer
MEMO
OPERATOR’S Manual
21
MEMO
22
GIANT-100 Receipt Printer
MEMO
OPERATOR’S Manual
23
GIANT-100
Receipt Printer
OPERATOR’S Manual
JK68-60036A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising