Clear-Com ICS-22 User manual

Clear-Com ICS-22 User manual
CLEAR-COM ECLIPSE
ICS-102/62
INTERCOM PANEL
INSTRUCTION MANUAL
ICS-102/62 Intercom Panel Instruction Manual
© 1998, 2000, 2004, 2005, 2009 Vitec Group Communications Ltd. All Rights Reserved.
Part Number 810302Z Rev. 3
Vitec Group Communications LLC
850 Marina Village Parkway
Alameda, CA 94501
U.S.A
Vitec Group Communications Ltd
7400 Beach Drive
IQ Cambridge
Cambridgeshire
United Kingdom
CB25 9TP
The Vitec Group plc
Beijing Representative Office
Room 706, Tower B
Derun Building, YongAn Dongli A No.3
Jianwai Ave., Chaoyang District
Beijing, P.R.China 100022
® Clear-Com, CellCom/FreeSpeak and the Clear-Com Communications Systems logo are registered trademarks of
The Vitec Group plc.
Website: www.clearcom.com
CONTENTS
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Front-Panel Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Communication-Error Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Speaker/Headset Level Controls. . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Intercom Volume Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Page Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Mute Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Listen Level Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Talk/Listen Selectors and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Selector Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Talk and Listen Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Monitoring/Eavesdropping Indicators . . . . . . . . . . . . . . . . . . . . . . 1-3
Call-Waiting Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
In-Use Tally Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Telephone Off-Hook Tally Indicator . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Radio Receiver Active Tally Indicator . . . . . . . . . . . . . . . . . . . . . . 1-4
Panel Connected Tally Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Audio Presence Tally Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Answer-Back Facility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Answer Back Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Answer-Back Label Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Removing Labels from the Answer-Back Stack . . . . . . . . . . . . . . 1-5
Function Selectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Panel Mic Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Speaker On Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Mic On Selector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Listen Level Selector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Listen-Level Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Listen Level Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Call Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Remote Telephone Line Release . . . . . . . . . . . . . . . . . . . . . . . 1-7
Rear-Panel Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Miscellaneous Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Logic Inputs #1 and #2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Programmable Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
i
Mute Relay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
OPT-100 Auxiliary Audio Option . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Hot Mic Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Studio/Stage Announce Audio and Relay Outputs . . . . . . . . . . 1-9
Auxiliary Audio Line Level Output . . . . . . . . . . . . . . . . . . . . . . 1-10
Expansion Panel Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Mounting Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Analog Matrix Frame to Panel Wiring . . . . . . . . . . . . . . . . . . . . . . 2-2
Digital Matrix Frame to Panel Wiring. . . . . . . . . . . . . . . . . . . . . . . 2-3
Single-Pair Digital . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Coax Digital . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Matrix Panel Miscellaneous Connector Wiring . . . . . . . . . . . . . . . 2-4
External Program Feed Input. . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Logic Input #1 and #2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Mute Relay Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Programmable Relay Contacts . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
OPT-100 Auxiliary Audio I/O Option . . . . . . . . . . . . . . . . . . . . . . . 2-8
Hot Mic Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Studio/Stage Announce Audio and Relay Outputs . . . . . . . . . . 2-8
Auxiliary Audio Line Level Output . . . . . . . . . . . . . . . . . . . . . . . 2-9
Mains AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Headset Sidetone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Panel Microphone Gain. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Speaker Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Page Volume Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Panel-to-Matrix Card Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Panel Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Technical Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Bill of Materials for the ICS-102/102T . . . . . . . . . . . . . . . . . . . . . . 3-3
Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
ICS-102/102T Main PCB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Bill of Materials for ICS-102 Selector Switch PCB . . . . . . . . . . . . . 3-20
ii
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Bill of Materials for ICS-102/102T Selector Switch LED PCB. . . . . 3-23
Bill of Materials for COM-20 Communication PCB (Part No. 710435) .
3-30
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
ICS-102/62 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
OPT-100 Auxiliary Audio I/O Option . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Accessory Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Eclipse Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Software Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Hardware Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . W-I
TECHNICAL SUPPORT & REPAIR POLICY. . . . . W-V
TECHNICAL SUPPORT POLICY . . . . . . . . . . . . . . . . . . . . . . . . . . W-v
RETURN MATERIAL AUTHORIZATION POLICY . . . . . . . . . . . . . W-vi
REPAIR POLICY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . W-viii
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
iii
iv
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
IMPORTANT SAFETY
INSTRUCTIONS
For your safety, it is important to read and follow these
instructions before operating an ICS-102/62 intercom station:
(1) WARNING: To reduce the risk of fire or electric shock, do not
expose an ICS-102/62 intercom station to rain or moisture. Do not
operate an ICS-102/62 intercom station near water, or place objects
containing liquid on it. Do not expose an ICS-102/62 intercom station
to splashing or dripping water.
Please read and follow
these instructions
before operating an
ICS-102/62 intercom
station.
(2) For proper ventilation, make sure ventilation openings are not
blocked. Install the ICS-102/62 according to the directions in the
Installation Chapter of this manual.
(3) Do not install an ICS-102/62 intercom station near a heat source
such as a radiator, heat register, stove, or other apparatus (including
amplifiers) that produces heat. Do not place naked flame sources such
as candles on or near an i-station.
(4) Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades, with one blade wider than the
other. A grounding-type plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
(5) Protect the power plug from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from
the i-station’s chassis.
(6) Only use attachments/accessories specified by Clear-Com
Communication Systems.
(7) Unplug the ICS-102/62 station during lightning storms or when
unused for long periods of time.
(8) Refer all servicing to qualified service personnel. Servicing is
required when:
• The ICS-102/62 station has been damaged in any way, such as
when a power-supply cord or plug is damaged.
• Liquid has been spilled or objects have fallen into the ICS-102/62
station’s chassis.
• The ICS-102/62 station has been exposed to rain or moisture.
• The ICS-102/62 station does not operate normally.
• The ICS-102/62 station has been dropped.
Please familiarize yourself with the safety symbols in Figure 1. When
you see these symbols on an ICS-102/62 intercom station, they warn
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
v
you of the potential danger of electric shock if the station is used
improperly. They also refer you to important operating and
maintenance instructions in the manual.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol alerts you to the presence of uninsulated dangerous
voltage within the product's enclosure that might be of sufficient
magnitude to constitute a risk of electric shock. Do not open
the product's case.
This symbol informs you that important operating and maintenance instructions are included in the literature accompanying
this product.
Figure 1: Safety Symbols
vi
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
1
OPERATION
INTRODUCTION
This manual describes how to use the ICS-102 and ICS-62 intercom
panels and their digital equivalents, the ICS-102T and ICS-62T
intercom panels. Panel operators can use this manual after the Eclipse
System has been correctly installed and configured.
DESCRIPTION
This chapter describes
how to operate the
ICS-102 and ICS-62
intercom panels and
the ICS-102T and
ICS-62T digital
panels.
The ICS-102/102T and ICS-62/62T intercom panels are each
assembled in a small, 1-RU high (1.75 in. or 44.45 mm) chassis. The
ICS-102/102T has ten selectors while the ICS-62/62T has six. Each
panel has the following features:
• Individually adjustable listen levels
• Fits in one rack unit (1.75 inches or 44.45 mm) of a standard
equipment rack
• Built-in speaker and optional plug-in panel microphone
• Front-panel headset connector
• Call signalling capability
• Answer Back facility
• Local program input without front-panel control
• Programmable relay
• Mute relay
• Two logic inputs for external control of selected panel functions
The panel can both be equipped with the following options:
• XPL-12 and XPL-22 Expansion Panels
• OPT-100 Auxiliary Audio Output.
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
1-1
FRONT-PANEL CONTROLS AND INDICATORS
The front-panel controls and indicators include:
• Communication-error indicator
• Talk/listen selectors and indicators
• Answer Back facility
• Function buttons
COMMUNICATION-ERROR INDICATOR
If the panel should lose data communication with the matrix frame, all
of the red lights on the front of the panel will flash slowly.
When data communication is restored, the panel will automatically
return to normal operation.
SPEAKER/HEADSET LEVEL CONTROLS
To adjust the speaker or headset volume, use the knob labeled
“intercom,” as described below. The speaker volume can also be
affected by three software-controlled functions: Page Override, Mute
Level, and Listen Level Adjustment.
INTERCOM VOLUME CONTROL
The “intercom” volume control sets the overall level of all signals
coming from the matrix frame, except for the page mode, which is
controlled by an internal software function (see the next section “Page
Override”).
PAGE OVERRIDE
Page Override is a special function in the panel in which the intercom
volume defaults to a preset to a value when commanded to by the
central matrix. Any fixed group can be assigned the page override
function through the configuration program.
The configuration program determines preset value for each panel. If
the preset value is lower than the setting of the front-panel volume
control, the volume will be controlled by the front panel control.
MUTE LEVEL
This turns down the speaker level when any talk is active at the panel.
The amount of muting (measured in dB) is set by the configuration
program for each panel. This function helps prevent possible feedback.
The maximum amount of muting is 15 dB below full volume. If the front
panel control is set below that level, then muting will have no effect.
1-2
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
LISTEN LEVEL ADJUSTMENT
The level of any active listen path can be adjusted individually. Refer to
“Listen-Level Mode” later in this chapter.
TALK/LISTEN SELECTORS AND INDICATORS
The following section describes the operation of the talk/listen
selectors and their associated indicators.
SELECTOR OPERATION
The selectors operate as both talk and listen selectors; they also work
as volume controls when the panel is in listen-level mode (see “Listen
Level Mode” later in this chapter). Pressing a selector down accesses
a talk label; pushing it up accesses a listen label. Pushing the talk
selector down and quickly releasing it will “latch” the selector and the
talk path will stay active until it is pressed again. Pressing and holding
a talk selector causes the talk path to stay active only for as long as it is
held down. Listen selectors operate in the same manner.
To prevent the selector on the panel from latching in the talk position
(local latch disable), or to prevent any panel from latching a talk to the
panel (global latch disable) use the configuration program.
TALK AND LISTEN INDICATORS
When a talk path is active, the red LED above the selector lights
continuously. When a listen path is active, the green LED above the
selector lights continuously.
MONITORING/EAVESDROPPING INDICATORS
If any other panel begins monitoring a panel, a beep (the
monitoring-alert tone) will sound at the panel.
To inhibit the monitoring-alert tone, use the configuration program.
CALL-WAITING INDICATOR
If a panel calls another panel with a selector programmed for that label,
the LED will rapidly flash red. This flashing is a call-waiting tally. To
answer the incoming call, push the indicated talk selector. The
call-waiting tally clears when the call is answered, or after the call is
terminated and the answer-back time-out lapses.
If another panel calls a panel without a button programmed for that
label, it will be placed in the answer-back stack (see “Removing Labels
from the Answer-Back Stack”).
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
1-3
IN-USE TALLY INDICATOR
If a selector is assigned to a label and another panel is currently using
that label, the LED will double-flash once per second to indicate the
label is in use. This tally must be enabled from the configuration
software.
TELEPHONE OFF-HOOK TALLY INDICATOR
When a telephone interface is assigned to a talk selector, the talk LED
will flash once per second if that telephone is off the hook. This tally
must be enabled from the configuration program.
RADIO RECEIVER ACTIVE TALLY INDICATOR
When a two-way radio interface port is assigned to a talk selector, the
LED will flash once per second when that radio’s receiver is active.
This tally must be enabled from the configuration program.
PANEL CONNECTED TALLY INDICATOR
This tally is used when a panel is connected to the frame by a
high-speed data line (such as an ISDN or T1 line) that might be
inactive periodically. The red LED of any talk selector associated with
that panel will flash once per second when the panel is on-line. This
tally must be enabled from the configuration program.
AUDIO PRESENCE TALLY INDICATOR
When a label is assigned to a listen selector, the LED will flash once
per second to indicate someone is talking on that channel. This tally
must be enabled from the configuration program.
ANSWER-BACK FACILITY
The primary function of the answer-back facility is to answer calls from
other panels or interfaces not assigned to a panel’s selectors.
The following sections describe the use of the answer-back facility.
ANSWER BACK SELECTOR
You use the Answer Back selector to answer calls from panels and
interfaces that are not assigned to your panel.
When a call from a panel or interface not assigned to the panel arrives:
• The calling panel’s label will be placed in the answer-back stack.
• The red LED will flash.
These two conditions will continue until the call is answered, or until
the answer-back time-out period lapses and the caller’s label is
1-4
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
automatically removed. To answer the call, push the Answer Back
selector. The red LED will turn off and the green LED will turn on,
indicating an active talk path to the caller. The talk path is active for as
long as the selector is held.
Note: The Answer Back selector cannot be latched; it is a
momentary-only function.
Calls from panels or interfaces assigned to panel selectors will only be
indicated by their associated LEDs.
ANSWER-BACK LABEL SELECTION
If another call comes in while using the answer-back selector:
• The user will hear the caller’s voice.
• The label will be placed in the answer-back stack.
To answer the next caller:
1. Push up on the Answer Back selector to remove the current caller’s
label.
2. Press down on the Answer Back selector to talk to the next caller.
REMOVING LABELS FROM THE ANSWER-BACK
STACK
Any label will be automatically removed from the stack if it is not
answered within a certain time interval, which is set by the
answer-back auto-clear time in the configuration program.
To manually remove the current caller’s label from the answer-back
stack, push up on the Answer Back selector.
FUNCTION SELECTORS
Two dual-function toggle switches allow you to choose among the
following four functions:
• Panel Mic
• Speaker On
• Mic On
• Listen Level
PANEL MIC SELECTOR
This selector selects the panel or headset microphone. If a headset is
plugged in, the panel will automatically switch to headset microphone
operation. If the headset is unplugged, the panel will automatically
switch back to panel microphone operation. The LED will be on when
the panel microphone is active.
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
1-5
SPEAKER ON SELECTOR
This selector functions only when a headset is plugged into the panel.
To toggle the speaker on and off, push the Speaker On selector. The
LED indicates when the speaker is on.
MIC ON SELECTOR
This selector activates the panel or headset microphone, whichever
has been selected. The LED indicates when the microphone is on. If a
talk is activated while the microphone is off, it will turn on.
LISTEN LEVEL SELECTOR
The Listen Level selector has four functions:
• Activating the listen-level mode
• Resetting the listen-level settings
• Sending call signals
• Releasing auto-answered telephone lines
Listen-Level Mode
To use the listen-level adjust mode, push (for less than 1 sec.) and
quickly release the Listen Level selector.
The LEDs of all active listen selectors will begin to flash to indicate the
function is on.
Note: Only active selectors can be adjusted in listen-level mode.
Use the selector associated with the intended label to increase (up) or
decrease (down) the volume.
To exit, push the Listen Level selector or wait for the 3 sec. time-out.
Note: If the active listen path is pushed higher than the maximum
value, the other paths will be driven down so that the
desired path has more emphasis.
Listen Level Reset
To reset the Listen Level to default settings:
1. Press (for less than 1 sec.) and quickly release the Listen Level
selector.
2. Press and hold the Listen Level selector for 3 sec.
3. Release the Listen Level selector.
1-6
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Call Signals
To activate a call signal:
1. Push and hold (for at least 1 sec.) the Listen Level selector until the
panel indicates it is in Call Signal mode.
2. Push down the talk selector with the desired label.
The call signal will be sent each time the selector with that label
assignment is pushed down and will remain so until the call-signal
mode times out (about 5 sec.).
Call signals can be issued to any talk label assigned to a panel’s
talk/listen selectors. If more than one label is assigned to a selector, all
labels will receive the signal. If a label is a fixed group, the entire group
will receive the call signal. If the label is a party line, then every panel
listening on the party line will receive the call signal.
Remote Telephone Line Release
This function is available only if specifically enabled in the
configuration program.
To hang up a telephone interface left off the hook:
1. Push and hold the Listen Level selector for at least 1 sec. to activate
the call-signal mode.
2. While holding the Listen Level selector, press the talk selector of the
desired telephone’s label.
3. Release the Listen Level selector.
Note: In addition to hanging up the telephone interface, this will
deactivate any talk/listen selector set to the interface from
anywhere in the system.
REAR-PANEL CONNECTORS
This section describes only those rear-panel functions directly affecting
normal panel operation. These include the functions available through
the “Miscellaneous” connector and those added by the use of the
“OPT-100 Auxiliary Audio” connector. The actual functions these inputs
and outputs perform depend on the installation of the individual panel.
This section only describes the general use of these functions. For a
more complete description, see the Installation chapter.
MISCELLANEOUS CONNECTOR
The Miscellaneous connector includes the following functions:
• Logic input #1
• Logic input #2
• Programmable relay
• Mute relay
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
1-7
Logic Inputs #1 and #2
Each input can control one of several functions, determined through
the configuration program. Typically, these inputs are connected to an
external foot switch, a panel-mounted switch, or the logic output of
another device.
The following functions are available:
• Mic On/Off—toggles the panel’s microphone on and off.
• Mute Mic Output To Frame—turns off the audio from the panel to
the frame. It does not turn off the Hot Mic output
• Mic Off —momentarily turns off the panel’s microphone.
• Answer Back Talk/Clear—functions the same as the panel’s
“Answer Back” selector. Holding down the switch activates a talk
to a label in the answer-back stack. To clear the label, quickly
press and release the switch.
• Studio Announce—sends the output of the panel’s selected
microphone (panel or headset) to the panel’s Studio Announce
(SA) audio output, and activates the SA relay. The microphone
output is not sent to the frame. The SA output and relay are only
present if the panel has the OPT-100 Auxiliary Audio I/O Option
installed.
• Speaker OFF—turns off the panel speaker, disabling all audible
output from the panel.
• PTT: Activate All Talk Keys—implements a push-to-talk function
for all talk selectors. When the logic input is active, the panel
operates normally. When the logic input is deactivated, all active
talk selectors are disabled. Any controls (relays, etc.) assigned to
the labels are activated or deactivated along with their assigned
labels. The LED indicators associated with the active talk
selectors operate normally regardless of the PTT status. This
input only controls latched talks.
• Activate Talk Switch #1— equivalent to pressing the panel’s first
(leftmost) talk selector; a momentary and latching activation.
• Activate Talk Switch #2—equivalent to pressing the panel’s
second talk selector; a momentary and latching activation.
• Activate Listen Labels Button—equivalent to pressing the “Listen
Labels” button to display listen labels on any display expansion
panel (XPL-12 or XPL-22) connected to the panel.
• PTT: Activate Two-Way Radio Keys—implements a push-to-talk
function for all two-way radio talk selectors. When the logic input
is active, the panel operates normally. When the logic input is
deactivated, all active two-way radio talk selectors are disabled.
Any controls (relays, etc.) assigned to the labels are activated or
deactivated along with their assigned labels. The LED indicators
1-8
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
associated with the active two-way radio talk selectors operate
normally regardless of the PTT status. This input only controls
latched talks.
Programmable Relay
Each Eclipse system panel includes a relay controlled by the system
program and independent of the local panel function. This relay can be
assigned to any label(s) in the system, which will activate whenever a
talk or listen is set to that label(s). If activating the relay is the only
action desired, assign the relay to a “control” label. See the Eclipse
Configuration System Manual for more details.
The relay can activate an external device, such as an applause light in
a studio, a cue light, or a security door lock. Any programmable relay in
the system can be activated from any panel in the system, including a
direct-inward-access caller.
Mute Relay
The mute relay is activated whenever any talk selector is activated at
the panel. The mute relay is commonly wired such that whenever it is
activated, the volume of the monitor speaker in that room is decreased
(muted).
OPT-100 AUXILIARY AUDIO OPTION
The OPT-100 Auxiliary Audio option provides the following features:
• Hot Mic output
• SA audio and relay outputs
• Auxiliary audio line level output.
Hot Mic Output
The Hot Mic output is a balanced, line-level, transformer-isolated feed
of the signal from the currently selected microphone (panel or
headset). The Hot Mic output is active regardless of whether the panel
has talk paths set and regardless of the front-panel’s control settings.
Studio/Stage Announce Audio and Relay Outputs
The SA output is a balanced, line-level, transformer-isolated feed with
the same signal sent to the Hot Mic output, except it is only active
when the SA button on the panel’s front panel is pressed or when
activated by Logic Input #1 or #2, which is configured for the Studio
Announce Function.
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
1-9
Auxiliary Audio Line Level Output
The Auxiliary Audio Line Level output is a balanced, line-level,
transformer-isolated feed of the input to the panel’s internal speaker.
For example, this output could be used to feed an external amplifier
connected to loudspeakers.
EXPANSION PANEL OPERATION
Optional expansion panels provide additional selectors that operate
the same way as a panel’s selectors, including talk, listen, tally, and
error indication.
The XPL-12 expansion panel provides 10 additional keys, while the
XPL-22 provides 20 additional keys. Each expansion panel offers
illuminated 5-character labels for every key.
Only one rack unit (1RU) of a standard Electronics Industry
Association equipment rack is required for each expansion panel. The
panels’ compact size makes them ideal for use in TV control rooms,
edit suites, mobile OB vans, and any other location where many
talk/listen keys are necessary but space it at a premium.
1-10
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
2
INSTALLATION
INTRODUCTION
This chapter describes the installation of the ICS-102/ICS-102T and
ICS-62/62T intercom panels, including:
• Panel placement
• Wiring
• Mains AC power
• Adjustments
• Configuration
• Accessory panels
MOUNTING PANELS
Locate all intercom panels at comfortable heights for operation and
leave at least 2 inches (51 mm) of clearance behind the rear of the
panel’s chassis to allow for cable connectors.
Accessory panels, that are intended to expand or enhance panel
operation, are usually mounted next to or near the panel with which
they are associated. Leave at least 2 inches (51 mm) of clearance
behind the rear of the panel to allow for cable connectors.
Accessory panels can be located as far as 25 ft. (7.6 m) away from the
panel. A 6-ft. (1.8 m) cable is supplied to connect them.
WIRING
This section provides detailed wiring diagrams for all panels’ wiring
systems.
Eclipse uses either a twisted, 4-pair transmission, a single-pair twisted,
or a coax scheme between the panel and the frame using the industry
standard RJ-45 connector. Refer to Installing an Eclipse Matrix
System: An Overview for RJ-45 connector installation and use, and the
type of cable needed for connection between panels and frames.
Most panels have a DB-15M and an RJ-45 connector to connect them
to the frame. Panels with only a DB-15M connector include a kit
containing one DB-15F/RJ-45 adapter. The adapter allows the use of
RJ-45 connectors on both ends of the connection between the frame
and the panel.
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
2-1
Connections to external devices via the Miscellaneous connector, use
the included DB-15M connector to construct one or more cables to
connect external devices to the panel.
The following sections describe connecting the panel to the matrix
frame, and all the connections between the panel and local devices.
Each of the following sections describes cable and panel connector
wiring:
• Analog matrix frame to panel wiring
• Digital matrix frame to panel wiring
• Matrix panel Miscellaneous connector wiring
• OPT-100 Auxiliary Audio I/O option
• Binaural headset wiring
ANALOG MATRIX FRAME TO PANEL WIRING
The analog audio RS-422 data communications module (COM-10)
uses a 4-pair wiring scheme between the frame and panels. This
module requires an MVX-A16 card in the frame.
Although some Matrix Panels have a DB-15M (male) connector for
connection to the Matrix frame, most have a built-in RJ-45 connector.
For those panels with a DB-15 male connector, Clear-Com provides a
properly wired DB-15F (female) to RJ-45 adapter for direct connection
with RJ-45 terminated cables. Additionally, panels configured for digital
communication are equipped with a BNC.
Four-pair analog wiring is typically wired with shielded CAT5 RJ-45
cable.
• Pair 1 transmits analog audio from the matrix port to the panel.
• Pair 2 transmits RS-422 data from the panel back to the matrix
card port.
• Pair 3 transmits analog audio from the panel to the matrix card
port.
• Pair 4 transmits RS-422 data from the matrix port back to the
panel.
2-2
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
ATT-T568B (Modular Jumpers
Wired One to One)
Panel End
Matrix Frame End
Pair 2
RS-422 eRceive +
1
RS-422 eRceive -
2
Audio Receive +
Audio Send +
Audio Send Audio Receive -
3
1
2
Pair 1
4
5
4
Pair 3
6
RS-422 eSnd +
7
RS-422 eSnd -
8
3
5
6
Pair 4
7
8
Figure 2-1: Matrix Frame to Panel Wiring
DIGITAL MATRIX FRAME TO PANEL WIRING
The ICS-102T and ICS-62T panels differ from the ICS-102 and ICS-62
panels because they contain an internal digital audio/data
communications module (COM-20) that works in conjunction with the
DIG-2 digital interface module to connect digital panels to the matrix.
The DIG-2 digital interface module offers two options for wiring the
frame to intercom panels. One option is a single pair of double
shielded (braid and foil) 24 AWG conductor CAT-6 Enhanced STP
cable with RJ-45 connectors.
The second option, available because only one pair is required, is
75-ohm (RG59) braid shielded coax cable. For this option, a BNC-16
adaptor is required.
In addition, each panel may require other connector wiring, depending
on what options and accessories are installed.
Note: For more information on the DIG-2 digital interface and the
DIF-102 frame which houses it, refer to the DIF-102/DIG-2
manual (part no. 810312Z) in the Eclipse set of manuals.
Single-Pair Digital
Single-pair digital wiring requires double-shielded 24 AWG conductor
CAT-6E enhanced STP cable with RJ-45 connectors. Pair 1 transmits
and receives multiplexed audio or data between the matrix port and
the panel.
Note: Ensure that the Select switch on the panel’s rear panel is in
the correct position for the intended use.
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
2-3
ATT-T568B (Modular Jumpers
Wired One to One)
Panel End
Matrix Frame End
No Connection (NC)
1
No Connection (NC)
2
1
2
Pair 1
3
No Connection (NC)
3
Multiplexed Data/Audio
4
4
Multiplexed Data/Audio
5
5
No Connection (NC)
6
6
No Connection (NC)
7
7
No Connection (NC)
8
8
Figure 2-2: Matrix Frame to Digital Panel Wiring Using RJ-45
Coax Digital
Coax digital wiring requires double-shielded 24 AWG conductor CAT-6
Enhanced STP cable connected to a 75-ohm (RG59) braid- shielded
coax cable with a BNC-16 adaptor.
Pair 1 transmits and receives multiplexed digital and analog between
the matrix port and the panel.
Note: Ensure that the Select switch on the panel’s rear panel is in
the correct position for the intended use.
Matrix Frame End
BNC-16
No Connection (NC)
1
1
No Connection (NC)
2
2
No Connection (NC)
3
3
Multiplexed Data/Audio
4
4
Multiplexed Data/Audio
5
5
No Connection (NC)
6
6
No Connection (NC)
7
7
No Connection (NC)
8
8
Panel End
Pair 1
Figure 2-3: Matrix Frame to Digital Panel Wiring Using BNC-16 and
Coax
MATRIX PANEL MISCELLANEOUS CONNECTOR
WIRING
Most local devices connect with the panel via the Miscellaneous
connector.
2-4
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
The following sections discuss how to wire the various functions
available on the “Miscellaneous” connector.
1
+ Program Input
9
2
- Program Input
Audio Ground
10
3
Second Ear Gr
ound
Second Ear Output
11
4
Logic Ground
Logic Ground
12
Logic Input #2
13
Mute Relay Normally Closed
14
Mute Relay Wipe
5
Logic Input #1
6
Panel Rela
y Normally Closed
7
Panel Rela
y Wipe
15
8
Mute Relay Normally Open
Panel Rela
y Normally Open
Figure 2-4: Miscellaneous Connector Pinout
External Program Feed Input
The external program feed input allows the panel operator to
simultaneously monitor audio from an external source and intercom
audio.
The input is designed to accept a balanced, line-level audio feed at a
nominal level of 0 dB. The program feed input passes through the
panel’s “Program” volume control before being mixed with the audio at
the panel. The program feed (program audio) can be heard on the
panel’s speaker and headset; it cannot be heard by other panels in the
Matrix system.
To connect an external program feed to the panel:
1. Connect the balanced audio pair to pins 1 and 9.
2. Connect a shield or ground connection if available to the connector’s
pin 2 (see Figure 8).
Logic Input #1 and #2
Each input can control one of several functions, determined through
the configuration program. Typically, these inputs are connected to an
external foot switch, a panel-mounted switch, or the logic output of
another device.
The following functions are available:
• Mic On/Off—toggles the panel’s microphone on and off.
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
2-5
• Mute Mic Output To Frame—turns off the audio from the panel to
the frame. It does not turn off the Hot Mic output (described in
“OPT-100 Auxiliary Audio I/O Option” on page 2-8). For an
example of how to use this option, see “External Program Feed
Input” on page 2-4).
• Mic Off —momentarily turns off the panel’s microphone.
• Answer Back Talk/Clear—the same functions as the panel’s
“Answer Back” key. Holding down the switch activates a talk to a
label in the answer-back stack. To clear the label, quickly press
and release the switch.
• Studio Announce—sends the output of the panel’s selected
microphone (panel or headset) to the panel’s Studio Announce
(SA) audio output, and activates the SA relay. The microphone
output is not sent to the frame. The SA output and relay are only
present if the panel has the OPT-100 Auxiliary Audio I/O Option
installed. (The SA options are described in “OPT-100 Auxiliary
Audio I/O Option” on page 2-8).
• Speaker OFF—turns off the panel speaker, disabling all audible
output from the panel.
• PTT: Activate All Talk Keys (Push To Talk)—when enabled from
the configuration program and the logic input is active, the panel
behaves normally. When this function (logic level) is deactivated,
it disables activation of all talk labels, implementing a push-to-talk
function for the panel. Any controls (relays, etc.) assigned to the
labels are activated or deactivated along with their assigned
labels. The LED indicators associated with the active labels
behave normally regardless of this input’s activity. This input
controls momentary and latched talks.
• Activate Talk Switch #1—equivalent to pressing the panel’s first
(leftmost) talk selector; a momentary and latching activation.
• Activate Talk Switch #2—equivalent to pressing the panel’s
second talk selector; a momentary and latching activation.
• Activate Listen Labels Button—equivalent to pressing the
“Listens” button on the keypad; all modes of the “Listens” button
are supported.
• PTT: Activate Two-Way Radio Keys—implements a push-to-talk
function for all two-way radio talk selectors. When the logic input
is active, the panel operates normally. When the logic input is
deactivated, all active two-way radio talk selectors are disabled.
Any controls (relays, etc.) assigned to the labels are activated or
deactivated along with their assigned labels. The LED indicators
associated with the active two-way radio talk selectors operate
normally regardless of the PTT status. This input only controls
latched talks.
2-6
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Use normally open type switches to activate the logic inputs. Connect
the switches as follows (see Figure 8):
• Logic input #1—pins 4 to 5 (pin 4 = ground)
• Logic input #2—Pins 11 to 12 (pin 11 = ground)
Note: Do not apply external voltage to the logic inputs.
Mute Relay Contacts
The mute relay is activated whenever any talk selector is activated at
the panel. The mute relay is commonly wired such that whenever it is
activated, the volume of the monitor speaker in that room is decreased
(muted). See Figure 2-4.
Both normally open and normally closed contacts are provided. They
are rated at 1 Amp at 24 VDC. This relay is not designed for switching
mains AC line voltage. To switch an external device running on mains
AC line voltage, use an external relay (or other switching mechanism)
activated by this relay.
Programmable Relay Contacts
Each panel includes a relay controlled by the system program and
independent of the local panel function. This relay can be assigned to
any label(s) in the system, which will activate whenever a talk or listen
is set to that label(s). If activating the relay is the only action desired,
assign the relay to a Control label. See the Eclipse Configuration
System Manual for more details.
The relay can activate an external device, such as an applause light in
a studio, a cue light, or a security door lock. Any programmable relay in
the system can be activated from any panel in the system, including a
direct-inward-access caller. Figure 2-4 shows the wiring of the relay
contacts to the Miscellaneous connector.
Both normally open and normally closed contacts are provided. They
are rated at 1 Amp at 24 V DC. This relay is not designed for switching
mains AC line voltage. To switch an external device running on mains
AC line voltage, use an external relay (or other switching mechanism)
activated by this relay.
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
2-7
OPT-100 AUXILIARY AUDIO I/O OPTION
The OPT-100 Auxiliary Audio option provides the following features:
• Hot Mic output
• SA audio and relay outputs
• Auxiliary audio line level output
Figure 2-5 shows the pinout for the intercom panel’s DB-15F Auxiliary
Audio I/O connector. Following are descriptions and wiring information
for the OPT-100 Auxiliary Audio I/O option.
"Auxiliary I/O" Connector DB-15F
1
9
+ SA Output
- SA Output
2
Audio Ground
3
SA Relay Normally Open
4
SA Relay Wiper
10
Audio Ground
Ground
11
12
Ground
5
13
SA Relay Normally Closed
- Aux Line Level Out
6
14
+ Aux Line Level Out
Ground
7
15
Ground
- Hot Microphone Out
8
+ Hot Microphone Out
Figure 2-5: Auxiliary I/O Connector
Hot Mic Output
The Hot Mic output is a balanced, line-level, transformer-isolated feed
of the signal from the currently selected microphone (panel or
headset). The Hot Mic output is active regardless of whether the panel
has talk paths set and regardless of the front-panel’s control settings.
Connect to pins 8 and 15 for a balanced output. Pin 7 is available as a
shield or ground source (see Figure 2-5).
Studio/Stage Announce Audio and Relay Outputs
The SA output is a balanced, line-level, transformer-isolated feed with
the same signal sent to the Hot Mic output, except it is only active
when the SA button on the panel’s front panel is pressed or when
activated by Logic Input #1 or #2, which is configured for the Studio
Announce Function.
2-8
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Connect to pins 1 and 9 for a balanced SA audio output. Pin 2 is
available as a shield or ground source (see Figure 2-5).
Both normally open and normally closed contacts are provided. They
are rated at 1 Amp at 24 VDC. This relay is not designed for switching
mains AC line voltage. To switch an external device running on mains
AC line voltage, use an external relay (or other switching mechanism)
activated by this relay (see Figure 2-5). The following table shows the
pins available for the SA relay.
Pin Description
Pin Number
N.O. (normally open)
WIPER (common)
N.C. (normally closed)
3
4
5
Table: 2-1 Studio Announce Pins Availability
Auxiliary Audio Line Level Output
The Auxiliary Audio Line Level output is a balanced, line-level,
transformer-isolated feed of the input to the panel’s internal speaker.
For example, this output could be used to feed an external amplifier
connected to loudspeakers.
Connect to pins 6 and 13 for a balanced output. Pin 14 is available as
a shield or ground source (see Figure 2-5).
MAINS AC POWER
The ICS-102/ICS-102T panels and ICS-62/ICS-62T panels can be
powered by any source supplying between 12 and 16 V RMS AC at
750 mA. The panels are shipped with a wall-mountable transformer
that provides 14 V RMS AC to the panel.
Two types of transformers are available: one operates on a mains AC
input power of 117 V (part number 730166) and the other operates on
a mains AC input power of 220 V (part number 820049). Make sure to
specify the proper transformer when ordering the panel.
To connect the transformer, route the cord from the transformer’s
secondary to the panel’s “AC Power Input” connector on the rear
panel. This is a 2.1 mm coax connector. When routing the cord make
sure to use the stress relief on the rear panel.
The power input to the panel is internally protected with a 0.9 a “poly
fuse,” a self-healing fuse that will recover when the fault is removed.
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
2-9
ADJUSTMENTS
The following panel parameters are adjustable either internally on the
panel’s main PCB, or externally by selecting options in the
configuration program:
• Headset sidetone (main PCB)
• Panel microphone gain (main PCB)
• Speaker mute (configuration program)
• Page volume level (configuration program)
• Panel-to-matrix card baud rate (configuration program)
All these parameters are set to factory defaults. Most panels should
operate at these default settings; however, some applications may
require readjustment.
HEADSET SIDETONE
Sidetone is the sound of the user’s voice in his headset.
To adjust sidetone:
1. Remove the panel cover.
2. Find the sidetone control (marked “P2 Sidetone”) on the main PCB.
See Figure 10.
3. Connect a headset to the panel.
4. While speaking into the headset microphone, use a small
screwdriver to turn the sidetone control until the sidetone is at the
desired level.
5. Re-install the panel cover.
Figure 2-6: Sidetone and Panel Microphone Gain Adjustment Controls
PANEL MICROPHONE GAIN
You can adjust the preamplifier gain of the panel microphone over a
range of 0 to 10 dB; the maximum is the panel microphone gain’s
default setting. However, if two panels are talking to each other at the
2-10
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
same time with the panel microphone gain set to maximum, feedback
may occur even if the speaker mute (see the “Speaker Mute” section,
next) is set to maximum. In this case, it will be necessary to turn the
panel microphone gain down. Similarly, in some noisy environments it
may be necessary to turn the panel microphone gain down and have
the operator talk more closely into the microphone.
To adjust the panel microphone gain:
1. Remove the panel cover.
2. Use a small screwdriver to adjust the control marked “P1” on the
Main PCB. See Figure 10.
3. Reinstall the panel’s cover.
SPEAKER MUTE
When a panel microphone and a speaker are used together, feedback
is possible. To reduce this possibility, the panel software will mute (turn
down) the speaker level by some predetermined amount when both
the microphone and speaker are enabled. The speaker mute can be
adjusted from 0 to 15 dB; its default setting is 6 dB.
Refer to the Eclipse Configuration System Instruction Manual for
instructions on muting the speaker.
PAGE VOLUME LEVEL
When Page Override is assigned to a label, the audio level at the
destination panel(s) is predetermined. This function allows talking to
someone even if his panel’s volume control is off. Two things will
happen when a panel activates such a label:
• If the destination speaker was off, it will turn on.
• The panel’s speaker output will be at the predetermined level
regardless of the “Intercom” volume control setting, unless this
control is set higher than the predetermined level.
The page volume level can be adjusted within a range of 0 to 10,
equivalent to the front-panel control settings of 0 equals off and 10
equals full pot. The page volume level’s default setting is 5.
Refer to the Eclipse Configuration System Instruction Manual for
instructions on using Page Override.
PANEL-TO-MATRIX CARD BAUD RATE
The RS-422 serial data communication between a panel and other
devices can operate at standard (19.2 k baud, the default) and
long-line (9600 baud) baud rates. Use long-line only if encountering
problems with the standard baud rate.
The baud rate is set from the configuration program and the panel
automatically adapts.
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
2-11
2-12
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
3
MAINTENANCE
INTRODUCTION
This chapter provides panel microprocessor resetting instructions,
troubleshooting guidelines, schematics, assembly drawings, and
component lists for the ICS-102/ICS-102T intercom panel.
The panel operates at 14 VAC, supplied from an external transformer.
Transformers can be ordered for either 117 VAC or 220 VAC.
PANEL RESET
The panel’s microprocessor has a reset button located in an unmarked
hole just below the “Intercoms” knob on the left side of the unit’s front
panel. If the panel is acting erratically, try resetting it by doing one of
the following:
• Insert a small screwdriver or a stiff piece of wire (such as a bent
paper clip) into the hole and push the reset button.
• Unplug the panel from AC power and reconnect.
Troubleshooting
When experiencing the symptoms listed below, attempt the following
solutions in the order outlined. The solutions are listed in order of
difficulty with the first being the most simple and easy.
• The panel’s LEDs and push-button lights fail to light.
1. Check mains AC power into the panel.
2. Ensure the external power supply is properly connected to the
panel.
3. Replace the panel.
• The LED indicator above a selector key does not light when the
key is pressed.
1. Ensure the selector key has a label assigned to it (the LED indicator
will not light without an assigned label).
2. Reset the panel.
3. Replace the panel.
• The panel appears to activate talk paths, but other panels can’t
hear the panel operator.
1. Check “Mic On/Off” and “Panel Mic” buttons to ensure the intended
microphone is selected and on.
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
3-1
2. If the correct microphone is turned on, ensure the panel audio has
not been muted externally through the logic inputs.
3. Make sure the panel has not been defined as a nearby panel.
4. Activate the Matrix Loopback mode from the panel’s Maintenance
menu to check the audio paths to the matrix.
5. Enable eavesdropping on the panel.
6. Test the integrity of the panel’s audio path by temporarily setting a
forced listen to it.
7. Reset the panel.
8. Replace the panel.
• The panel is inoperative and all red LEDs flash slowly.
1. Wait 60 sec. If the matrix frame has just been powered up, it is
possible it is still downloading the configuration to the port cards.
2. Ensure the cable connecting the panel to the matrix is plugged in at
both ends.
3. Check the integrity of the data paths, especially the polarity for
panels using a COM-10 communication module.
4. Check the configuration program to ensure the panel has been
assigned the correct port type.
5. Confirm the port card or interface type matches the panel. Panels
with COM-10 communication modules should have MTX-A16 cards.
Panels with COM-20 communication modules connect to DIG-2
interfaces.
6. Reset the panel’s port card in the matrix frame.
7. Replace the panel’s port card in the matrix frame.
8. Reset the panel.
9. Replace the panel.
• No audio from the panel’s speaker.
1. Ensure the Intercom knob on the panel’s front panel is turned up.
2. Ensure the Speaker On/Off button is on.
3. Check whether audio can be heard in a headphone.
4. Use the configuration computer or an ICS-2003 panel’s
programming feature to test the integrity of the panel’s audio path by
temporarily setting a forced listen to it.
5. Reset the panel’s port card in the Matrix frame.
6. Replace the panel’s port card in the Matrix frame.
7. Reset the panel.
8. Replace the panel.
• The operator cannot hear another panel’s page or call signal
tones.
1. Adjust the “Page Volume” control of the panel using the
configuration program (refer to the Eclipse Configuration System
Manual).
3-2
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
2. Check the panel’s configuration to see if page override is enabled.
• Announce tones (eavesdropping indication, change tones, etc.)
aren’t heard at the panel.
1. Adjust the panel’s “Page Volume” control in the configuration
program (refer to the Eclipse Configuration System Manual).
2. Check the panel’s Configuration menu to see if page override is
enabled.
• Accessory panel keys do not function.
1. Check the accessory panel’s connection on the panel’s rear panel.
2. Ensure the external AC power transformers are correctly connected
to the accessory panels.
3. Check the configuration program to ensure the correct number of
keys are configured.
TECHNICAL REFERENCE
BILL OF MATERIALS FOR THE ICS-102/102T
Device
Cable
Cable
Cable
Clamp
Flash ROM
Speaker
Transformer
Transformer
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Description
10-PIN FLAT CABLE
16-PIN FLAT CABLE
34-PIN FLAT CABLE
CABLE CLAMP, 3/16IN PLASTIC
ICS-102 PROGRAM
41 X 71MM, SMALL MAGNET
POWER PLUG-IN 117/14VAC
POWER PLUG-IN 220/14VAC
Part #
770001
770008
730181
640054
710416
500138
400008
400011
3-3
Figure 3-7: Digital Block Diagram—ICS-102/102T Main PCB
3-4
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
SERIAL
BUS TO
XP
PANELS
AUX RELAY
MUTE RELAY
DATA IN
DATA OUT
CLOCK
RESET
DATA
DUAL DIGITAL
POTS
FOOT SWITCH INPUT
EXTRA LOGIC INPUT
HEADPHONE SENSE INPUT
DUAL DIGITAL
POTS
STROBE
FRONT PANEL
TALK/LISTEN KEYS &
LEDS
8-BIT SHIFT
REGISTER
CLOCK
CLOCK
OSC
MICROPROCESSOR
RESET
A/D BUS
A8-A15
LO PASS
FILTER
A8-A15
ADDRESS
DECODER
CONTROL BUS
RAM
MEMORY
16K BYTES
A/D BUS
ADDRESS BUS A0-A15
ADDRESS
LATCH
A0-A7
PROGRAM
MEMORY
32K BYTES
A/D BUS
ANNOUNCE
TONES OUTPUT
TO AUDIO
ICS-102 DIGITAL BLOCK DIAGRAM
A/D BUS
PORT
’E’
INPUTS
LATCH
FRONT
PANEL
PROGRAM
VOLUME
INTERCOM
VOLUME
COM
MODULE
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
2365
2176
2059
1841
ECO#
A
REV
DESCRIPTION
RELEASE
ADD C82
8
FLASH ROM ADDITION
REVISED
04/28/97
12/20/95
DATE
6/16/93
10/12/93
CM
BY
BH
MP
BH
CHK
1N5401
C21
+
0 ohm
R35
4700uF
C22 +
4700uF
6.8V ZD
D14
2.2K
R33
10K
R32
2.2K
R25
10K
R24
6.8V ZD
D3
2
2
D4
4050
8
4050
4050
4050
D5
Q5
MPSA05
D13
1
7
3
14
5
11
7
9
Q4
MPSA55
3
D16
4700uF
C23 +
+
R36
0 ohm
IC7A
2
IC7F
15
IC7B
4
IC7E
12
4050
4050
3
C
2
4700uF
C24
1N5401
D17
R34
22 1W
220
R41
220
R40
IC7C
6
IC7D
10
1
D12
D6
XP RESET
D11
XP/AUDIO CLOCK
C19
VO
D9
R30
240
+
220uF 25V
1N4001
R29
2.4K
220uF 25V
R27
240
R28
2.4K
+
D8
1N4001
LM337T
D10
1N4001
IC10
VI
100
R31
100
1N4001
LM317T
OUT 1
C20
IN
IC9
D7
R26
3
XP/AUDIO DATA OUT
GND
D
14 VAC
F1
.90A POLY
22 1W
R37
R38
22 1W
R39
220
GND 2
B
UNUSED
EXTERNAL
POWER
TRANSFORMER
9
10
UNUSED
J4
1
8
GND.
6
GND.
7
5
RESET
KEY DATA
4
3
SER CLOCK
+ SUPPLY
2
+ SUPPLY
1
6
2
7
3
8
4
9
5
GND 4
6
-15V
-15V
SOURCE
100uF 25V
+ C17
100uF 25V
AGND
+15V
SOURCE
+ C16
+15V
XP/AUDIO DATA OUT
XP/AUDIO CLOCK
AUDIO RESET
POT SERIAL DATA OUT
POT SERIAL CLOCK
POT SERIAL RESET
HEAD SENSE INPUT
ANNOUNCE TONE OUTPUT
C12
1uF MONO
PD0
PD1
PD2
PD3
PD4
PD5
7
ANALOG
GROUND
SOURCE
1000uF
C15
+
SER DATA
SER CLK
SER RESET
POT DATA
POT CLK.
POT RESET
HEAD SENSE
BEEP
14
D15
3
VI
IC11
42
41
40
39
38
37
36
35
09
10
11
12
13
14
15
16
5
DIGITAL
GROUND
SOURCE
7805T
VO
AS 04
E 05
R/W 06
43
PE0 45
PE1 47
PE2 49
PE3 44
PE4
PE5 46
PE6 48
PE7 50
A8
A9
A10
A11
A12
A13
A14
A15
A/D0
A/D1
A/D2
A/D3
A/D4
A/D5
A/D6
A/D7
1N4001
IC3A
2 74HC00
1
+5D
ANALOG CIRCUITS
TO SHEET 2
C25
.1uF
52 VRH
51 VRL
20
21
22
23
24
25
XP/AUDIO DATA OUT
XP/AUDIO CLOCK
XP RESET
AUDIO RESET
AUX. RELAY OUTPUT
XP PANEL DATA RETURN
R17
+5D
1K
IC1
68HC11
R2
3.3K
GND
A
B
FRONT
PANEL
SELECT
KEYS
J3
1
SER DATA
J2
C3
.1uF
R11
100K
1
1
+5D
Q2
R12
2 10K
3
R16
10K
MPSA13
R9
100K
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
18 /NMI
19 /IRQ
07 XTAL
34
33
32
31
30
29
28
27
Y1
8.000MHz
08 TAL
EXTRA LOGIC INPUT
FOOT SW INPUT
HEAD SENSE INPUT
MUTE RELAY OUTPUT
ANNOUNCE TONE OUT
POT SERIAL DATA OUT
POT SERIAL CLOCK
POT SERIAL RESET
27pF
27pF
C2
R1
10M
26 VDD
17 /RES
XP PANEL DATA OUT----XP PANEL UNREG +VOLT.XP PANEL CLOCK OUT---XP PANEL UNREG +VOLT.XP PANEL RESET OUT---XP PANEL GND. -------XP PANEL KEY DATA----XP PANEL GND. -------NO CONNECT------------
TO EXTRA
KEY PANELS
DB-9
1
(AUX. RELAY)
R19
47
2
R8
3.3K
C1
C14
.1uF
VSS 01
R15
2.2K
3
K1
Q1
MPSA13
TP1
IRQ
47
R10
10K
C11
.01uF
+5D
TP3
C9
.1uF
02 MODB
03 MODA
+5D
1
(MUTE RELAY)
R18
R13
100K
IC6
TL7705AP
3.3K
R3
+5D
C18
PE2
PE3
PE4
PE5
PE6
PE7
PE0
AS
E
R/W
R/W
E
AS
DGND
+5D
+5V DIGITAL SOURCE
A15
100uF 25V
+
A8
A9
A10
A11
A12
A13
A14
A15
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
A6
A4
A2
A0
A1
A3
A5
A7
IC3C
10 74HC00
9
IC3D
13 74HC00
12
IC2
74HC373 20
2
3
D0 4
5 Q0
Q1
D1 7
6 Q2
D2 8
9
D3
12 Q3
D4 13
15 Q4
D5 14
16 Q5
Q6
D6 17
19 Q7
D7 18
OC 1
G 11
10
C26
.1uF
C81
D19
F1
IC24
J2
16
G1
G2A
G2B
8
A
B
C
+5D
O0
O1
O2
O3
O4
O5
O6
O7
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
C5
.1uF
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
D0
D1
D2
D3
D4
D5
D6
D7
IC5
62C256L
11
12
13
15
16
17
18
19
14
(H2000-H27FF)
7
IC24C
10 74HC00
9
(E)
+5D
8
28
+5D
10
9
8
7
6
5
4
3
25
24
21
23
2
26
1
C6
.1uF
3
(E)
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
6
C81
.1uF
3
4
7
8
13
14
17
18
Q0
Q1
Q2
Q3
Q4
Q5
Q6
Q7
2
5
6
9
12
15
16
19
+15A
R4
10K
22 A3
21 A2
COMMUNICATIONS
MODULE
3
3
IC24B
4 74HC00
5
LISTEN AUDIO
TALK AUDIO
IC12
74HC374
AD0
AD1
AD2
AD3
AD4
AD5
AD6
20
1
11 OC
CLK
10
D0
D1
D2
D3
D4
D5
D6
D7
RP-1
10K
2
537642
PE7
PE6
PE5
PE4
PE3
PE2
PE0
1
DATE
DATE
SCALE
--------
PLOT SIZE -
D
SW-1
SW-2
SW-3
SIZE
05/12/93
D
CW
P1
CLEAR-COM
INTERCOM SYSTEMS
SCHEMATIC
1
710304-SCH-D-
ICS-102 MAIN BOARD
SHEET #1
DWG NO.
TITLE:
5K
LISTEN
LEVEL
FUNCTION SWITCH PWB P/N 710306
7103041D.ORC
DATE
ORCAD P/N -
CHK
16
DWN Clark McCoy
+5VD
SPEAKER ON
PANEL MIC
LISTEN LEVEL
MIC ON
ANS BACK DW
CALL WAITING
SW-4
R1 1K
1K
1K
RESET SWITCH
D2
D1
R3 1K
D3
PANEL MIC
SPEAKER ON
R4
D4
LISTEN LEVEL
R2
R5
D6
D5
MIC ON
1K
EXTRA KEYS & LEDS
ON FRONT PANEL
R6 1K
1
ANS BACK DW
CALL WAITING
APP
C7
.01uF
15
10
12
11
9
1
3
6
5
14
8
7
13
2
J6
4
34 A GND.
33 LISTEN AUDIO
32 A GND.
31 TALK AUDIO
30 -15V ANALOG SUPPLY
29 +15V ANALOG SUPPLY
28 A GND.
27 A GND.
26 D GND.
25 D GND.
24 /LIST. EN
-15A
E
20 A1
19 A0
18 AS
17
16 /RST
15 R/W
14 /CE1
13 /CE0
12 AD7
11 AD6
10 AD5
9 AD4
8 AD3
7 AD2
6 AD1
5 AD0
4 IRQ
3 +5D
2 +5D
J5
1 +5D
23 /TALK EN
A3
A2
A1
A0
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
+5D
/LIST EN
+5D
AS
E
/RST
R/W
IRQ
2
/TALK EN
(/H3800-H3FFF)
(/H3000-H37FF)
20
%%oCS%%o
22
%%oOE%%o
27
%%oWE%%o
(/WR)
14
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
IC24A
2 74HC00
1
(H4000-H7FFF RAM SPACE)
IC4
74HC138
15
14
13
12
11
10
9
7
6
IC8
29C256
11
12
13
15
16
17
18
19
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
ANALOG CIRCUITS
TO SHEET 2
6
4
5
A13
A14
A15
4
11
(/RD)
(CONTROL BUS)
1
2
3
K2
P2
R105
Y1
28
IC3B
5 74HC00
4
IC24D
13 74HC00
12
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
20 %%oCE%%o
22 %%oOE%%o
1 VPP
14
10
9
8
7
6
5
4
3
25
24
21
23
2
26
27
+5D
(A0-A7)
(A8-A15)
(AD0-AD7)
A11
A12
A14
A8
A9
A10
A11
A12
A13
A14
A0
A1
A2
A3
A4
A5
A6
A7
LAST USED DESIGNATORS
8
11
AD6
AD4
AD2
AD0
AD1
AD3
AD5
AD7
C4
.1uF
4
GND
D1
1N4001
D2
1N4001
K2
R14
10K
+ C10
47uF
16V
+5D TP2
+5D
GND
+15A
+15A
R21
470K
+5D
R7
3.3K
/RST
C13
.022uF
220K
3
Q3
MPSA13
CT
RO 6
/RO 5
REF 1
+5D
(CONTROL BUS)
5
VCC
MISC.
CONNECTOR
DB-15F
1
9
2
10
3
11
4
12
5
13
6
14
7
15
8
2
3
RIN
R6
3.3K
6
VCC
LOGIC GND.-----LOGIC GND.-----EXTRA LOGIC IN-FOOT SWITCH IN-MUTE RELAY N.C.AUX. RELAY N.C.MUTE RELAY WIPEAUX. RELAY WIPEMUTE RELAY N.O.AUX. RELAY N.O.-
J1
R22
R20
10K
2
C8
.1uF
+5D
SEN
JP2
+5D
R5
10K
VCC
7
+PROGRAM INPUT--PROGRAM INPUT-AUDIO GND.------
+PRG-IN
-PRG-IN
R23
4.7K
+5D
7
8
GND
C
D
8
/RST
VCC
Figure 3-8: ICS-102 Main PCB Schematic Rev D (part 1)
3-5
REV D
R
A
B
C
D
Figure 3-9: ICS-102 Audio Block Diagram
3-6
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
MICROPHONE
HEADSET
MICROPHONE
PANEL
RS-422 COM MODULE
LISTEN
4-WIRE
TALK
4-WIRE
OUT
FEED
SPEAKER
OUTPUT
SA
OUTPUT
HOT MIC
AUX. AUDIO OPTION
EQ
EQ
Local
Sidetone
Adjust
LIMITER
ANNOUNCE TONE
FROM
MICROPROCESSOR
MICROPROCESSOR
CONTROLLED
AUDIO SWITCH
MICROPROCESSOR
CONTROLLED GAIN
BLOCK
ICS-102 AUDIO BLOCK DIAGRAM
-
+
INPUT
PROGRAM
BALLANCED
HEADPHONE
SPEAKER
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
8
-PRG-IN
+PRG-IN
7
.22uF
.22uF
C46
C45
R62
39.2K*
R79
39.2K*
R80
39.2K*
C44
100pF
C71
.1uF
3
2
4
-15A
IC18A
NE5532
1
100pF
C59
R78
39.2K*
+15A
8
A
FROM
SHEET 1
QS 9
10
%%oQS%%o
(SA ENABLE)
C70
.1uF
IC13D
16 DG211
14
6
15
-15A
+15A
5
6
C48
.1uF
R93
10K
1uF NP
IC18B
NE5532
7
P2
5K POT
R96
1M
Q8
2N2222
R84
470K
+15V 2.2M
R89
C80
.1uF
IC15A
NE5532
C62
R92
56K
3
J174
Q6
-15A
(SIDETONE)
(ADJUST)
S
D
3
2
.1uF
C61
C82
200pF
Q7
7
5
2
IC15B
NE5532
2N2222
5
R85
3.3K
6
R94
10K
R83
10K
10K
R81
R86
3.3K
R82
10K
.1uF
C57
.0047uF
R95
3K
10K
R73
FROM
SHEET 1
3
2
TO SHEET 1
-15A
IC16A
NE5532
1
100pF
C72
R105
10K
+15A
IC16B
NE5532
7
100pF
C54
R71 10K
POT DATA
POT CLK.
POT RESET
TALK AUDIO
6
5
C76
.1uF
C74
.1uF
(TALK BUS)
10K
R104
C63
4
5.1V .1uF
ZD
D19
R68
10K
IC19A
DS1267-10
10K POT
R65
10K
H
W
H
W
R63
2.7K
+15A
L
12
10
22uF
C51
-15A
R64
2.7K
5.1V ZD
D18
IC19B
DS1267-10
10K POT
4
3
L
6
CLK 8
13
DIN 5
9
DOUT /R
11
2
7
8
C69
.1uF
+5D
2
13
4
R87
10K
22K
C56
.047uF
4.7K
(BEEP FILTER)
1
(PANEL SEL)
(HEADSET SEL)
(HEAD SIDETONE SEL)
(PRG ENABLE)
(/LIST. EN)
(/TALK EN)
5
.1uF
C47
IC13A
DG211
7
10
BEEP
R90
10K
R72
150K
5
6
C52
+ C50
22uF
3
2
.1uF
C49
IC23B
NE5532
7
100pF
C53
3
-15A
3
IC23A
NE5532
1
100pF
+15A
4
IC14
4094
4
5
6
7
14
13
12
11
1
3
(SIDETONE SW)
12
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Q8
7
IC20B
LM833
IC13B
DG211
IC13C
DG211
1
24K
R91
200pF 5%
C58
8
16
C27
100
R60
1K
.01uF
5
6
R45
R54
4.02K*
.0068uF
8
6
9
11
2
C60
R77
R76
4
C73
.1uF
C75
.1uF
33K
C35
.1uF
R75
C67
.22uF
5.1K
3
2
2
22
R48
R47
22
7
IC17B
NE5532
+
IC21
LM384
C28
DATE
DATE
SCALE
--------
PLOT SIZE -
D
R42
22K
SIZE
05/12/93
+ C33
4.7uF
7103042D.ORC
DATE
ORCAD P/N -
CHK
22uF
D
+15A
-15A
J10
X
Y
1
4
2 3
HEADPHONE
CONNECTOR
FRONT PANEL
SPEAKER
OPT-2
AUXILLIARY
INTERFACE
MODULE
SCHEMATIC
CLEAR-COM
INTERCOM SYSTEMS
26 LINE OUTPUT
25
24 DIGITAL GND.
23 DIGITAL GND.
22 DIGITAL GND.
21 DIGITAL GND.
20 DIGITAL GND.
19 DIGITAL GND.
18 DIGITAL GND.
17 DIGITAL GND.
16
15
14
13 SA CONTROL
12
11
10 ANALOG GND.
9 ANALOG GND.
8 +15 SUPPLY
7 +15 SUPPLY
6 -15 SUPPLY
5 -15 SUPPLY
4
3 TALK BUS
2 ANALOG GND.
J11
1 ANALOG GND.
3
2
1
3
2
J9
1
3
2
J8
1
1
1
710304-SCH-D-
ICS-102 MAIN BOARD
SHEET #2
DWG NO.
TITLE:
+15V
+15V
TO
MIC
PREAMP
.1uF
+
C64
R101
2.2
5.1
R99
+
R43
15K
+5VD
220uF
C85
,4,5,10,
11,12,13
8
C68
1000uF
DWN Clark McCoy
TO
SHEET 1
HEAD SENSE
5
6
2
6
APP
.1uF
C36
IC17A
NE5532
-15V
R100
8.2K
47pF
R74
150K
1
C55
+15V
C77
1uF NP
R103
0
-15V
C65
.0039uF
R97
2
4
1 STR
2 D
3
15 CLK
OE
1uF NP
C34
82
C31
4.02K*
C41
.002uF
22uF
TANT
R58
47
-15A
R59
1
C39
IC20A
LM833
R88
1.2K
LISTEN AUDIO
5
4
+5D
Y
R49
47K
+
22uF
R46
3
C40
.002uF
R44
220
R53
4.02K*
+
2
FROM
HEADSET
CONNECTOR
C29
C42
.1uF
R51
.002uF
FROM
SHEET 1
3
x
+ C43
22uF
C30
R52
4.02K*
4.02K*
C32 .0047uF
R57
47
4
1
3
HEADSET MIC.
R50
22K
100
2
22uF TANT
R56
+15A
4
8
8
SER DATA
SER CLK.
SER RESET
/TALK EN
/LIST EN
R61
C38
8
4.7K
22uF
TANT
500
CW
C79
.1uF
8
14
+
B
2
3
R55
10K
P1
+15A
6
7
FROM
SHEET 1
S
J7
1
C37
+
T
TO PANEL
MICROPHONE
R
+15A
+
3
C
D
7
1
+
8
14
1
1
Figure 3-10: ICS-102 Main PCB Schematic Rev D (part 2)
3-7
REV D
R
A
B
C
D
BLANK PAGE
3-8
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Figure 3-11: Main PCB
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
3-9
BILL OF MATERIALS
ICS-102/102T MAIN PCB
Capacitors
Designator
Description
C1 C2
27 PF CERAMIC 50V 5%
2
C55
47 PF CERAMIC 50V 10%
1
C44 C52 C53 C54 C59 C72 100 PF CERAMIC 50V 10%
6
C60 C82
200 PF CERAMIC 100V 5%
2
C41
6800 PF CERAMIC 50V 5%
1
C65 C66
.001 UF CERAMIC 30V 20%
2
C30 C31 C40
.0022 UF MYLAR 100V 5%
3
C32
.0047 UF MYLAR 50V 5%
1
C57
.0047 UF CERAMIC 50V 10%
1
C7 C11 C27
.01 UF CERAMIC 30V 20%
3
C13
.022 UF MYLAR 100V 10%
1
C56
.047 UF MONO 50V 10%
1
C9 C14 C25 C26 C35 C36 .1 UF MONO 50V 10%
C47 C48 C49 C58 C61 C63
C3 C4 C5 C6 C8 C76 C79
C80 C81 C64 C67 C69 C70
C71 C73 C74 C75
29
C42
.1 UF MONO 100V 10%
1
C45 C46
.22 UF MYLAR 100V 20%
2
C12 C18
1 UF CERAMIC 50V 10%
2
C3 C62 C77 C78
1 UF ALUMINUM NP 50V 10% 4
C33
2.2 UF ALUMINUM NP 50V
1
C38 C39
22 UF TANT. 16V
2
C28 C29 C37 C43 C50 C51 22 UF ALUMINUM 16V 20%
3-10
Qty
6
C84 C83
33 UF ALU LOW ESR 35V 20% 2
C10
47 UF ALUMINUM 16V 20%
1
C16 C17
100 UF ALUMINUM 25V 20%
2
C19 C20
220 UF ALUMINUM 25V
2
C68
1000 UF ALUMINUM 35V
1
C21 C22 C23 C24
4700 UF ALUMINUM 25V
4
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Resistors & Resistor Packs
Designator
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Description
Qty
R99 R103
1 OHM 1/4W CARBON FILM
5%
2
R101
2.2 OHMS 1/4W CARBON FILM 1
5%
R47 R48
22 OHMS 1/4W CARBON FILM 2
5%
R38
22 OHMS 1W CARBON FILM
5%
R18 R19 R57 R58
47 OHMS 1/4W CARBON FILM 4
5%
R46
82 OHMS 1/4W CARBON FILM 1
5%
R26 R31 R45 R56
100 OHMS 1/4W CARBON
FILM 5%
4
R39 R40 R41 R44
220 OHMS 1/4W CARBON
FILM 5%
4
R27 R30
240 OHMS 1/4W CARBON
FILM 5%
2
P1
5 OHMS TRIM POT
1
R17 R60
1K OHMS 1/4W CARBON FILM 2
5%
R88
1.2 OHMS 1/4W CARBON FILM 1
5%
R15 R24 R32
2.2K OHMS 1/4W CARBON
FILM 5%
3
R28 R29
2.4K OHMS 1/4W CARBON
FILM 5%
2
R63 R64
2.7K OHMS 1/4W CARBON
FILM 5%
2
R73
3.0K OHMS 1/4W CARBON
FILM 5%
1
R2 R3 R6 R7 R8 R85 R86
3.3K OHMS 1/4W CARBON
FILM 5%
7
R51 R52 R53 R54 R59
4.02K OHMS 1/8W METAL
FILM 1%
5
R23 R61 R76
4.7K OHMS 1/4W CARBON
FILM 5%
3
P2
5K OHMS TRIM POT
1
1
3-11
Designator
R100 R102
3-12
Description
8.2K OHMS 1/4W CARBON
FILM 5%
Qty
2
R4 R5 R10 R12 R14 R16
10K OHMS 1/4W CARBON
R20 R25 R33 R55 R65 R68 FILM 5%
R71 R81 R82 R83 R87 R90
R93 R94 R95 R104 R105
23
RP1
1 OHM X 9 R-PACK
1
R43
15K OHMS 1/4W CARBON
FILM 5%
1
R42 R50 R77 R97 R98
R106 R107 R108 R109
22K OHMS 1/4W CARBON
FILM 5%
9
R91
24K OHMS 1/4W CARBON
FILM 5%
1
R75
33K OHMS 1/4W CARBON
FILM 5%
1
R62 R78 R79 R80
39.2K OHMS 1/8W METAL
FILM 1%
4
R49
47K OHMS 1/4W CARBON
FILM 5%
1
R92
56K OHMS 1/4W CARBON
FILM 5%
1
R9 R11 R13
100K OHMS 1/4W CARBON
FILM 5%
3
R72 R74
150K OHMS 1/4W CARBON
FILM 5%
2
R22
220K OHMS 1/4W CARBON
FILM 5%
1
R21 R84
470K OHMS 1/4W CARBON
FILM 5%
2
R96
1M OHM 1/4W CARBON FILM
5%
1
R89
2.2M OHMS 1/4W CARBON
FILM 5%
1
R1
10M OHMS 1/4W CARBON
FILM 5%
1
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Diodes and Transistors
Designator
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Description
Qty
D3 D14
DIODE 1N957B ZENER 6.8V
.4W 5%
2
D1 D2 D7 D8 D9 D10 D15
DIODE 1N4003 RECT 1A
200PIV
7
D4 D5 D6 D11 D12 D13
DIODE 1N4148 SIGNAL 10MA 6
75PIV
D18 D19
DIODE 1N5231B ZENER 5.1V
.5W 5%
2
D20
DIODE 1N5339 ZENER 5.6V
5W
1
D16 D17
DIODE 1N5401 RECT 3A
100PIV
2
Q7 Q8 Q9 Q10 Q11 Q12
TRANSISTOR 2N2222 NPN
30V
6
Q6
TRANSISTOR J174 JFET
PCHAN 8V VGS
1
Q5
TRANSISTOR MPS-A05 NPN
60V
1
Q1 Q2 Q3
TRANSISTOR MPS-A13 NPN
30V DARL
3
Q4
TRANSISTOR MPS-A55 PNP
60V
1
3-13
Integrated Circuits
Designator
3-14
Description
Qty
IC7
4050B CMOS HEX BUFFER
1
IC14
4094B CMOS 8 BIT SHIFT
REGISTER
1
IC1
68HC11A CMOS MCU 52 PIN
PLCC FP
1
IC3 IC24
4HC00 CMOS QUAD NAND
2
IC4
74HC138 CMOS 3 TO 8 LINE
DECODER
1
IC2
74HC373 CMOS OCTAL D
LATCH
1
IC12
74HC374 CMOS OCTAL D
FL/FLOP
1
IC13
DG211CJ CMOS QUAD ANALOG SWITCH
1
IC5
GM76C256L CMOS SRAM 32K 1
X 8 100NS
IC19
DS1267-10 DIGITAL POT,
DUAL 10K
1
IC21 IC22
LM384 OPAMP, POWER 4W
2
IC20
LM833N OPAMP, DUAL LO
NOISE
1
IC15 IC16 IC17 IC18 IC23
NE5532 OPAMP, DUAL LO
NOISE
5
IC25
78SR105HC REGULATOR, 5V 1
SWITCHER 1A
IC9
LM317T REGULATOR, POS
ADJ 1.5A
1
IC10
LM337T REGULATOR, NEG
ADJ 1.5A
1
IC6
TL7705AP RESET SUPERVISOR IC
1
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Miscellaneous
Designator
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Description
Qty
J4
CONNECTOR 2.1MM CO-AX
PC MTG POWER
1
J2
CONNECTOR DB-9F RT ANG
PC MTG
1
J1
CONNECTOR DB-15F RT ANG 1
PC MTG
Y1
CRYSTAL 8.000MHZ PARALLEL CRYSTAL
1
F1
FUSE 0.90A POLY SWITCH
1
JP2
JUMP JACK JUMP JAX
1
K1 K2
RELAY SPDT 12V PC RELAY
ITT#SZ12
2
3-15
3-16
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
DATE
6/16/93
BY
BH
BH
7
CHK
VO
4.7uF
16V
C2 +
13
14
C3
6
.1uF
7
IC5D
4001
C4
.1uF
J3-3
J1-3
R
IC3
4094
(2.2K)
(20 PLACES)
R20
RED & GREEN
LED PAIRS
D20
G
(GND. SOURCE)
(+5V SOURCE)
+5V
J3-6
J1-6
G
5
+5V
J3-7
J1-7
+5V
S2
#2
SWITCH P.C.B. ASSY# 710253
7
D
Q 13
11 CLKIC4B
4013
12
%%oQ%%o
9
14
+5V
J3-8
J1-8
C3
.1uF
S1
#1
4
IC5C
4001
9
8
10
S5
#5
S4
#4
+5V
IC1
4094
S3
#3
S6
#6
D6
6
5
IC5B
4001
3
4
IC2
4094
S7
#7
D7
16
8
DESCRIPTION
RELEASE
1841
ECO#
A
REV
7/13/93
IC6
3
J3-5
C2
.1uF
J3-1
8
J1-5
11
IC2
4094
R
ASSY# 710308
10
C5 WAS 100pF
J1-10 N/C
.1uF
C1
7805L
VI
G
D5
D4
+5V
+5V
3
5
S8
#8
D8
S9
#9
D9
C5
.001
Q 1
IC4A
CLK
4013 2
%%oQ%%o
D
S10
#10
D10
IC3
4094
2
2
TITLE:
10
9
8
6
4
2
5
3
7
1
1
SIZE
DWG NO.
C June 28, 1999 720147-SCH-C0
Date: Monday,
Sheet
1
of
SCHEMATIC
ICS-102
SELECTOR SWITCH ASY.
CLEAR-COM
INTERCOM SYSTEMS
LOGIC GND.
OUT
UNREGULATED
+5VDC OUT
RESET OUT
CLOCK OUT
SW DATA INPUT
LED DATA OUT
OUTPUT TO NEXT
EXPANSION I/O PANEL
Document Number
04/05/93
Size
C
1:1
PLOT SIZE SCALE
720147SB.ORC
DATE
CHK
J2-8
J2-6
J2-4
J2-2
J2-5
J2-3
J2-7
J2-1
J2-9 N/C
D11
J2-10 N/C
+5V
ORCAD P/N -
DATE
DATE
DWN Clark McCoy
100
R8
R7
10K
APP
4
2028
B
10
J1-9 N/C
J1-8
J1-6
J1-4
R
15
3
2
1
9
8
6
4
2
G
15
3
2
1
A
LOGIC GND.
INPUT
UNREGULATED
+5VDC INPUT
R
16
J1-1
12
G
+5V
R
D3
R
J1-2
2
IC5A
4001
15
3
2
1
1
G
D2
S
B
J3-2
N/C
J3-4
8
J1-2
SW1
R
4.7K
SW2
16
J1-4
R
SW5
R5 4.7K
SW3
10 %%oQS%%o
9 QS
11 Q8
12
13 Q7
14 Q6
7 Q5
OE
6 Q4
CLK
5 Q3
Q2
D
4 Q1
STR
C1
.1uF
IC1
4094
SW4
15
3
2
1
S
R6
G
SW6
R4
100K
R
8
R3
100K
G
8
+5V
R
SW7
10 %%oQS%%o
9 QS
11
12 Q8
Q7
13 Q6
14 Q5
7 Q4
OE
6 Q3
CLK
5 Q2
D
4 Q1
STR
16
N/C
G
8
J1-5
R
SW8
15
3
2
1
J1-3
G
D1
DOWN
3
6
5
R2
4.7K
R
UP
4
8
3
+5V
R1
D1
LED Printed Circuit Board
(DATA OUT)
SW9
R1
100K
J1-7
(DATA IN)
5
SW10
10 %%oQS%%o
9 QS
11 Q8
12 Q7
13 Q6
14 Q5
7 Q4
OE
6
CLK
5 Q3
D
4 Q2
Q1
STR
16
RESET IN
7
SW. DATA OUT
J1-1
6
10 %%oQS%%o
9 QS
11 Q8
12
13 Q7
14 Q6
7 Q5
OE
6 Q4
CLK
5 Q3
Q2
D
4 Q1
STR
15
3
2
1
CLOCK IN
1
LED DATA IN
7
10 %%oQS%%o
9 QS
11 Q8
12 Q7
13 Q6
14 Q5
7 Q4
OE
6 Q3
CLK
5
D
4 Q2
Q1
STR
C
D
8
INPUT FROM STATION or
PREVIOUS EXPANSION PANEL
10 %%oQS%%o
9 QS
11
12 Q8
13 Q7
14 Q6
7 Q5
OE
6 Q4
Q3
CLK
5 Q2
D
4 Q1
STR
8
16
GND
Figure 3-12: ICS-102/ICS-102T Selector Switch PCB Schemtatic Rev B
3-17
Rev
REV
B
0
R
A
B
C
D
BLANK PAGE
3-18
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Figure 3-13: ICS-102/102T Selector Switch PCB
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
3-19
BILL OF MATERIALS FOR ICS-102 SELECTOR SWITCH
PCB
Capacitors
Designator
Description
Qty
C5
0.001 uF Ceramic Disc 30 20% 1
C1 C3 C4
0.1 uF Monolithic 50 10%
3
C2
4.7 uF Aluminum 50
1
Resistors & Resistor Packs
Designator
Description
Qty
R8
100 OHM 1/4 Carbon Film 5%
1
R2 R5 R6
4.7K OHM 1/4 Carbon Film 5% 3
R7
10K OHM 1/4 Carbon Film 5%
R1 R3 R4
100K OHM 1/4 Carbon Film 5% 3
1
Diodes and Transistors
Designator
Description
D1 D2 D3 D4 D5 D6 D7 D8 Diode 1N4148 SIGNAL 10MA
D9 D10 D11
75PIV
Qty
11
Integrated Circuits
Designator
3-20
Description
Qty
IC5
Logic Chip 4001 CMOS 4 2 IN
NOR GATE
1
IC4
Logic Chip 4013 CMOS DUAL D 1
FF
IC1 IC2 IC3
Logic Chip 4094B CMOS SHIFT 3
REGISTER
IC6
Regulator 7805L POS 5V REG. 1
TO-92 PKG
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Miscellaneous
Designator
S1 S2 S3 S4 S5 S6 S7 S8
S9 S10 S10
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Description
SWITCH SP3T
MOM-OFF-MOM PC MTG
Qty
11
3-21
Figure 3-14: Assembly Drawing ICS-102/102T Selector Switch LED
PCB
3-22
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
BILL OF MATERIALS FOR ICS-102/102T SELECTOR
SWITCH LED PCB
Capacitors
Designator
C1 C2 C3
Description
0.1 uF Monolithic 50V 10%
Qty
3
Resistors & Resistor Packs
Designator
R1-R20(20)
Description
1K OHM 1/4 Carbon Film 5%
Qty
20
Integrated Circuits
Designator
IC1 IC2 IC3
Description
Qty
Logic Chip 4094B CMOS SHIFT 3
REGISTER
Miscellaneous
Designator
Description
D2 D4 D6 D8 D10 D12 D14 LED GREEN, ROUND, FLAT
D16 D18 D20
TOP LED
D1 D3 D5 D7 D9 D11 D13
D15 D19
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Qty
10
LED RED, ROUND, FLAT TOP 9
LED
3-23
3-24
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
DATE
6/16/93
BY
BH
BH
7
CHK
4.7uF
16V
C2 +
14
C3
6
.1uF
7
IC5D
4001
C4
.1uF
IC3
4094
(2.2K)
(20 PLACES)
R20
RED & GREEN
LED PAIRS
D20
G
(GND. SOURCE)
(+5V SOURCE)
+5V
J3-3
J1-3
R
5
+5V
J3-7
J1-7
+5V
S2
#2
D2
SWITCH P.C.B. ASSY# 710253
7
D
Q 13
11 CLKIC4B
4013
12
%%oQ%%o
9
14
+5V
J3-8
J1-8
C3
.1uF
S1
#1
D1
4
9
8
10
S5
#5
S4
#4
IC5C
4001
D5
D4
+5V
IC1
4094
S3
#3
D3
S6
#6
D6
6
5
IC5B
4001
3
4
IC2
4094
S7
#7
D7
16
8
DESCRIPTION
RELEASE
1841
ECO#
A
REV
7/13/93
IC6
VO
13
G
10
C5 WAS 100pF
J1-10 N/C
.1uF
C1
7805L
VI
3
J3-6
J3-5
J3-1
C2
.1uF
J1-6
8
J1-5
11
IC2
4094
R
ASSY# 710308
+5V
+5V
3
5
S8
#8
D8
S9
#9
D9
C5
.001
Q 1
IC4A
CLK
4013 2
%%oQ%%o
D
S10
#10
D10
IC3
4094
2
2
TITLE:
10
9
8
6
4
2
5
3
7
1
1
SIZE
DWG NO.
C June 28, 1999 720147-SCH-CDate: Monday,
Sheet
0
1
of
SCHEMATIC
ICS-102
SELECTOR SWITCH ASY.
CLEAR-COM
INTERCOM SYSTEMS
LOGIC GND.
OUT
UNREGULATED
+5VDC OUT
RESET OUT
CLOCK OUT
SW DATA INPUT
LED DATA OUT
OUTPUT TO NEXT
EXPANSION I/O PANEL
Document Number
04/05/93
Size
C
1:1
PLOT SIZE SCALE
720147SB.ORC
DATE
CHK
J2-8
J2-6
J2-4
J2-2
J2-5
J2-3
J2-7
J2-1
J2-9 N/C
D11
J2-10 N/C
+5V
ORCAD P/N -
DATE
DATE
DWN Clark McCoy
100
R8
R7
10K
APP
4
2028
B
10
J1-9 N/C
J1-8
J1-6
J1-4
G
15
3
2
1
9
8
6
4
R
15
3
2
1
A
LOGIC GND.
INPUT
UNREGULATED
+5VDC INPUT
G
16
J1-1
12
R
R
J1-2
2
IC5A
4001
15
3
2
1
1
G
+5V
R
3
S
2
J3-2
N/C
J3-4
8
J1-2
SW1
R
4.7K
SW2
16
J1-4
SW5
R5 4.7K
SW3
10 %%oQS%%o
9 QS
11 Q8
12 Q7
13 Q6
14 Q5
7 Q4
OE
6 Q3
CLK
5
D
4 Q2
Q1
STR
C1
.1uF
G
SW6
15
3
2
1
R6
SW4
IC1
4094
R
SW7
10 %%oQS%%o
9 QS
11 Q8
12 Q7
13 Q6
14 Q5
7 Q4
OE
6 Q3
CLK
5
D
4 Q2
Q1
STR
S
J1-5
G
SW8
R4
100K
R
8
R3
100K
G
8
+5V
R
SW9
16
N/C
G
DOWN
8
J1-3
R
10 %%oQS%%o
9 QS
11 Q8
12 Q7
13 Q6
14 Q5
7 Q4
OE
6 Q3
CLK
5
D
4 Q2
Q1
STR
15
3
2
1
5
R2
4.7K
G
UP
4
6
3
+5V
R1
D1
R
LED Printed Circuit Board
(DATA OUT)
SW10
R1
100K
J1-7
(DATA IN)
5
8
RESET IN
7
SW. DATA OUT
J1-1
6
10 %%oQS%%o
9 QS
11 Q8
12 Q7
13 Q6
14 Q5
7 Q4
OE
6 Q3
CLK
5 Q2
D
4 Q1
STR
16
CLOCK IN
1
LED DATA IN
7
10 %%oQS%%o
9 QS
11 Q8
12 Q7
13 Q6
14 Q5
7 Q4
OE
6 Q3
CLK
5
D
4 Q2
Q1
STR
15
3
2
1
B
C
D
8
INPUT FROM STATION or
PREVIOUS EXPANSION PANEL
10 %%oQS%%o
9 QS
11 Q8
12 Q7
13 Q6
14 Q5
7 Q4
OE
6 Q3
CLK
5
D
4 Q2
Q1
STR
8
16
GND
Figure 3-15: ICS-102/102T Selector Switch PCB Schematic
3-25
Rev
REV
B
0
R
A
B
C
D
BLANK PAGE
3-26
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
DESCRIPTION
Release to production
2573
ECO#
B
DATE
04-07-99
A
BY
JEG
MAS
CHK
C32
C42
.1uF
(IC6)
C41
.1uF
(IC6)
C40
.1uF
(IC6)
.1uF
(IC6)
C33
.1uF
(IC6)
C10
.1uF
(IC1)
DSP56004
.1uF
(IC1)
C34
C35
C45
.1uF
(IC6)
.1uF
(IC6)
.1uF
(IC1)
C44
.1uF
(IC1)
C23
C37
10uF
(IC7)
.1uF
(IC6)
B
C26
.1uF
(IC3)
C27
.1uF
(IC4)
VCC
.1uF
(IC7)
C48
R30 2.2
+5A0
10uF
(IC7)
+ C25
.1uF
(IC7)
.1uF
(IC8)
C50
OP Amp
.1uF
(IC9)
C3
VCC
C49
C47
.1uF
(IC5)
VCC
Filtered CODEC Power
+5D0
C38
.1uF
(IC2)
VCC
+ C24
VCC
L1
.1uF
(IC1)
VCC
C46
.1uF
(IC1)
C36
.0047uF
Serial Audio
51
SCKR57
SDI0 56
SDI1 50
WST
SCKT 49
47
SDO0 46
SDO1 45
SDO2 55
WSR
\\\
\\\
\\\ (Jitter)
10uF
.1uF
5
6
7
IC8B
LMC6482
.33uF
C21
TP3
LISTEN
(Second of four SSYNC pulses)
Next Frame
.47uF
.47uF
VREF
+ C18
C14
.001uF*
BAV99
Top
View
SOT-23
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Shown 4-times
life size
Pinout for 80-Pin
QFP Package
DSP560004
Digital
Ground
Plane
Region
3
CDOUT
SMODE3
SDIN
SDOUT
SCLK
SSYNC
/RESET
CLKIN
VD
DGND
n/c
Note: Talk and Listen amplifier gain issues.
2
1
AGND
/MSC0
MA15/MCS3
MA14
MA13
AVCC
MA12
AGND
QVCC
QGND
MA11
MA10
MA9
MA8
AGND
MA7
AVCC
MA6
MA5
MA4
TEST
LIN
VDD
n/c
LOUT
VBias
VRef
34
35
36
37
38
39
40
41
42
43
44
Shown 3-times
life size
Pinout for
44-Pin TQFP
Package
CS4218
26
27
28
1
2
3
4
MT8971BP
Pinout for
28-Pin PLCC
Package
Shown 2-times
life size
DSCK/OS1
DSI/OS0
DSO
SDI0
SDI1
WSR
SGND
QVCC
QGND
SCKR
WST
SCKT
SVCC
SDO0
SDO1
SDO2
SGND
/HREQ
/SS/HA2
MOSI/HA0
18
17
16
15
14
13
12
22
21
20
19
18
17
16
15
14
13
12
n/c
/F0o
DSTi/Di
DSTo/Do
VSS
CDSTo/CDo
CDSTi/CDi
LIN2
LIN1
RIN2
RIN1
VA
AGND
REFGND
REFBYP
REFBUF
n/c
n/c
Analog
Ground
Plane
Region
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
Test1
Test0
/CODECRES
FSYNC
SCLK
C8
CPUA0
CPUA1
CPUA2
CPUA3
Test4
Test3
Test2
(gnd)
CPUA4
Test5
/CPURES
CPUEClk
CPUD4
CPUD5
CPUD6 (J4)
CPUD7
CPUCE0
CPUCE1
CPUR/W
DSP Program
Write and Read FRAMER data.
Right Xmit ISR (Sync and restart ISR states)
Update ISR buffers
Interrupt ISRs Right Rcv ISR
Left Xmit ISR
C
DI1
Mute
Ver
G3 G2 G1 G0
1
ADV DI1 --
D
1
OF:
SCALE -----------------------
SHEET:
ORCAD P/N 710435SC.DSN
APP
1
DATE
E
SIZE D
DATE
ADV
DATE 04-07-99
DO1 A4 A3 A2 A1 A0
MSK
CHK
SPMISO
SPMOSI
DWN J.E.Galbraith
PC Board #170264
Schematic
INTERCOM SYSTEMS
CLEAR-COM
DWG No.
710435 - SCH - D -
COM-20 Digital Subscriber Station
TITLE:
"0 dBu" reference level is 0.775 Vrms (impedence not specified).
CODEC output Listen amplifier gain is set to +9dB.
CODEC output attenuation is set to -13.5dB.
"LISTEN_AUDIO" level should be the same as "TALK_AUDIO".
Input Talk amplifier gain is set to -36dB.
SPCLK
Right Xmit ISR (next ISR state)
The MATRIX+III sets a +10dBu headroom above maximum audio level.
CODEC nominal input gain is set to +12dB and can be adjusted between 0dB and +22.5dB.
GPIO0
--
Right Rcv ISR
Audio Conversion \\\ Wait for next FRM8KHz/Right Xmit ISR sync
Left Rcv ISR
LSBMSB
LSBMSB
CSDO - TP23
LSBMSB
REV C
®
CODEC input clipping level is +2dBu (REFBUF voltage + 1.0Vrms).
LSBMSB
LSBMSB
CSDI - TP22
SCLK (1MHz) - TP20
DSP Serial Command Interface to CODEC timing (Typical Transaction)
Sync on falling edge of GPIO0. (Interrupt Mask=1, Mute is off, Gain (G(3..0)) is 8 (+12dB), Attenuation (A(4..0)) is 9 (-13.5dB), Mute=0, DO1=0, ADV=1, DI1=1.)
DSP/CODEC
R25
4.75K*
+ C17
47pF
R18
75.0K*
(DSP/EPROM)
(CODEC)
VCC
GND
VCC
GCLK/1
I
VCC
ACLK/I
I
MODE
/CPUIRQ
CPUD0
CPUD1
CPUD2
CPUD3
"TALK_AUDIO" input level is limited in the station to +6dBu.
Right Word Bits
+ C19
C20
R22
0
C11
R18,C14=75uS Deemphasis
GND
Shown 4-times
life size
Pinout for 144-Pin
TQFP Package
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
The COM20 input and output gains are set to match those of a COM10 4-wire interface in a typical station.
CS4218
NC 13
8
NC 11
NC 12
NC
16
REFGND
REFBUF14
REFBYP15
C12
.0047uF
Gain Adjust, R17 +600 Ohms
R17
R16
0
7.50K*
TP5
LOUT
CGND
BNC
J5
RJ-45
Listen Amplifier
4.75K*
4.75K* +5D0 SM4 Mode
+5D0 Slave 32 BPF
TP4
ROUT
32 BPF
TS 1
R9
R10
FOR COAX
2
1
FOR RJ-45
S1
3
5
4
6
J2
1
2
3
4 + 2-Wire Data
5 - 2-Wire Data
6
7
8
DB-15M
I
ACLK/I
VCC
I
GCLK/1
VCC
GND
GND
SSYNC (32KHz) - TP21
Left Word Bits
DSP Serial Audio Interface to CODEC timing
\\\
DNIC/FPGA/PLL clock timing
4.75K*
40 /RESET
34
33 CDOUT
CDIN
29 CCLK
30 /CCS
32 /INT
10
LOUT 9
ROUT
NC 44
NC 1
NC 2
NC 3
NC 4
NC 5
NC 6
DO1 31
35
SMODE3
26
SMODE2
23
SMODE1
MF6 28
MF7 25
MF8 24
MD0
MD1
MD2
MD3
MD4
MD5
MD6
MD7
.47uF
+ C6
+ 2-Wire Data
- 2-Wire Data
710451 FPGA
FRM8KHz/Sync - TP27
SCLK Period = 977 nS
\\\
C16 Period = 61 nS
+5D0
R32
GPIO0
4.75K*
21
19 LIN1
RIN1
22 LIN2
20 RIN2
27 DI1
2
1 /TW
3 TW
5
6
4 T1
VCC
/F0 (8KHz) - TP12
Ref, SSYNC
SCLK (1MHz) - TP20
SSYNC (32KHz) - TP21
FRM8KHz/Sync - TP27
/F0 (8KHz) - TP12
C4_DNIC - IC9,Pin14
/C4 - IC9,Pin3
C8/CLKIN - IC7,Pin41
C16 - IC9,Pin4
R24
SPMISO
SPMOSI
SPCLK
/CODECRES
+5D0
4.75K*
Note: TP1 indicates the DSP internal program activity (including interrupt ISRs). Sync on either TP12 or rising edge of TP27.
DSP program - TP1
FPGA/DSP/CODEC
DNIC
FPGA/DSP/CODEC
DNIC
PLL/FPGA
Sync on /F0 or rising edge of FRM8KHz.
DSP56004
R13
604*
C13
.0047uF
+5D0
R19
CSDO
11
12
13
15
16
17
18
19
IC7
+5A0
62256
20 %%oCS%%o
22 %%oOE%%o
27 %%oWE%%o
/BOOTRAMCE
/MRD
/MWR
IC5
D0
D1
D2
D3
D4
D5
D6
D7
BAV99
3
D1
10
9
8
7
6
5
4
3
25
24
21
23
2
26
1
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
Boot RAM
TP20 SCLK
TP21 SSYNC
+5D0
TP22 CSDI
TP23 CSDO
Short TP23
to TP22 for
CODEC audio
loop-back
C8
41 CLKIN
SCLK
38 SCLK
SSYNC
39 SSYNC
CSDI R43 1.0K
36 SDIN
CSDO
37 SDOUT
7 /PDN
R12
4.75K*
+5D0
SSYNC
SCLK
CSDI
4.75K*
VCC
.47uF
+ C5
.022uF
VCC
MA0
MA1
MA2
MA3
MA4
MA5
MA6
MA7
MA8
MA9
MA10
MA11
MA12
MA13
MA14
VCC
.47uF
IC3
MT9171BP
VREF 4
VBIAS 3
25
NC 20
NC 18
NC
392*
R4
47.5*
+ C4
1
2
3
4
5
6
7
DSI/OSO 8
DSCK/OS1 9
DSO 10
DR 11
n/c 12
n/c 13
n/c 14
15
n/c 16
gnd 17
gnd 18
19
C16In 20
n/c 21
22
SPCLK 23
SPMISO 24
SPMOSI 25
HA2 26
HREQ 27
GPIO0 28
GPIO1 29
30
GPIO2 31
GPIO3 32
DSPRES 33
MODA/IRQA 34
MODB/IRQB 35
MODC/IRQC 36
n/c
DSTo
DSTi
CDSTo
CDSTi
F0
11 n/c
10 /F0/CLD
9 RegC
8 MS0
7 MS1
6 n/c
5 MS2
REV
4/22/99
C31
.1uF
(IC1)
C39
VCC
C29
604*
R29
OnCE Serial
59 DSI/OS0
60 DSCK/OS1
58 DSO
61 %%oDR%%o
Gen Purpose I/O
73 GPIO3
74 GPIO2
75 GPIO1
76 GPIO0
R11
22 OSC1
1
6 NC
11 NC
NC
DSTI
DSTO
F0/CLD
LIN 27
C4/TCK
F0O/RCK
REGC
LOUT DIS24
PRECAN
OSC2
1
9
2
10
3
11
4
12
5
13
6
14
7
15
8
/C4/TCK 19
n/c 20
OSC2 21
OSC1 22
Precan 23
LOUT DIS 24
n/c 25
.1uF
(IC1)
IC8A
LMC6482
1
+5A0
COM3A FRAMER
VREF
3
2
VCC
C10
VCC
C2
n/c
LOUT
ROUT
n/c
/PDN
n/c
n/c
n/c
n/c
n/c
n/c
C28
.001uF*
R28
4.99K*
VCC
R42 R44
R45
4.75K* 4.75K* 4.75K*
S/W
TP1
OUT 3
VCC 4
IC4
OSC 10.24MHz
GND
OE
R3
(DNIC)
11
10
9
8
7
6
5
4
3
2
1
.1uF
(IC1)
VCC
TP18
C22
R27
4.75K*
DSI/OSO
DSCK/OS1
DSO
/DR
GPIO3
FRM8KHz
GPIO1
GPIO0
Boot CE Sync
TP46 TP27
.1uF
C52
R38
301*
R37
2.74K*
R6
4.75K*
.0033uF C9
C43
IC6
R41
.1uF
PCAP 32
4.75K*
(IC6)
PGND31
MD0
PINIT 30
MD1
MD2
MD3
C10
MD4
EXTAL 27
EXTAL=10.24 MHz
MD5
PLL MF=5
MD6
DSP Clock=51.2 MHz
MD7
Ext Memory
78
77 %%oMWR%%o
TP14 DSP Reset
%%oMRD%%o
25 MA0
24
36
/DSPRES
%%oRESET%%o
23 MA1
22 MA2
20 MA3
37
MODA/IRQA
MODA/IRQA
MODB/IRQB
19 MA4
38
MODB/IRQB
18 MA5
39
MODC/NMI
MODC/NMI
16 MA6
MA7
14 MA8
13 MA9
12 MA10
R33
4.75K*
11 MA11
VCC
7
5 MA12
Serial Host Interface
SPCLK
4 MA13
26
SCK/SCL35
SPMISO
3 MA14
MISO/SDA
SPMOSI
80 MA15/MCS3
41
MOSI/HA0
/HA2
79 MA16/MCS2
42
MA17/MCS1
SS/HA243
2 %%oMCS0%%o
%%oHREQ%%o HREQ
71
69
68
67
65
64
63
62
VCC
74HCT4046
10
DEMO15
ZEN
VCOIN9
2
1
TEST 26
LOUT 2
J1
23
24
25
26
27
28
29
30
31
32
33
.33uF
R26
75.0K*
1.0K*
1.0K*
1.0K*
1.0K*
1.0K*
1.0K*
1.0K*
1.0K*
1.0K*
1.0K*
1.0K*
1.0K*
1.0K*
1.0K*
1.0K*
/MCS
604*
1.0K*
MA0
MA1
MA2
MA3
MA4
MA5
MA6
MA7
MA8
MA9
MA10
MA11
MA12
MA13
MA14
R58
R59
R60
R62
R63
R64
R65
R67
R68
R69
R70
R71
R72
R73
R74
/MWR R55
/MRD R56
MD0
MD1
MD2
MD3
MD4
MD5
MD6
MD7
R39
3.24K*
7 CX
5
11 INH
12 R1
R2
Phase Locked Loop
IC9
14 SIN
PP 1
3 CIN
P1 2
13
4 VCOUT P2
6 CX
16
15
10
19
17
9
23
21
C1
.0015uF
E
SMODE1
MF8
MF7
SMODE2
DI1
MF6
CCLK
/CCS
DO1
/INT
CDIN
C16
47pF
Gain Adjust, R27
Talk Amplifier
R26,C22=75uS Preemphasis C15
R75
0
Out for: ICS52
ICS62
ICS92
ICS102
ICS1502
In for: ISC2003
ICS2110
MA0
CPU Interface
MA0 37
MA1
107
MA1 39
MA2
106 %%oCPUIRQ%%o
CPUD0
MA2 40
MA3
105 CPUD1
MA3 41
MA4
104 CPUD2
MA4 43
103
MA5
MA5 44
MA6
101 CPUD3
45
CPUD4
MA6
MA7
100 CPUD5
MA7 46
99 CPUD6
47
MA8
MA8
98 CPUD7
MA9
MA9 48
97 /CE0
MA10
MA10 49
MA11
96 /AS--/CE1
51
MA11 52
95 /OE--R/W
MA12
MA12
93
MA13
MA13 53
MA14
92 /WEL--/RST
MA14 55
89 /RES--E
86 A1--AS
57
/BOOTRAMCE
%%oBootRamCE%%o
/MCS
85 A2--A0
59
%%oMCS%%o
84 A3--A1
60
/MWR
%%oMWR%%o
/MRD
83 A4--A2
61
A5--A3
%%oMRD%%o
62
MD0
MD0
Sel)
MD1
108(CPU
MODE
MD1 63
MD2
MD2 64
MD3
MD3 65
MD4
MD4 67
MD5
MD5 68
MD6
MD6 69
MD7
MD7 70
129
DSI/OSO
127 Test7
8
DSI/OSO9
DSCK/OS1
88 Test6
DSCK/OS1
DSO
82 Test5
10
DSO 11
/DR
81 Test4
DR
80 Test3
78 Test2
21
R40
0
GCLK/I 18
77 Test1
R35
0
Test0
ACLK/I
R36
0
ACLK/I 90
R34
0
I 17
47pF
C51
C4_DNIC
TP12 /F0
VCC
(RAM)
SVCC
MODC/NMI
MODB/IRQB
MODA/IRQA
/RESET
MISO/SDA
SGND
PVCC
PCAP
PGND
PINIT
QGND
QVCC
EXTAL
SCK/SCL
MA0
MA1
MA2
MA3
AGND
ADJUST TALK GAIN; R27
TP24
TP45
4.75K*
TP30 and TP45 are installed
as a two pin jumper jack to
select processor type.
TP30
VCC
R1
220*
220*
220*
220*
220*
220*
220*
220*
220*
100uF
.1uF
R46
R47
R48
R49
R50
R51
R52
R53
R54
+ C7
C8
C8
SCLK
SSYNC
/C4
C16
DSTi
DSTo
/F0
CDSTi
CDSTo
MA0
TP25
/IRQ
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
/CE0
/CE1
R/W
/RST
E
AS
A0
A1
A2
A3
L3
71
72
38
143
109
110
73
C8Out 74
CODECSClk
75
CODECFSync
DSTi 3
DSTo 2
F0 6
/C4Out 56
C16In 20
5
CDSTi 4
CDSTo
n/c 12
n/c 13
n/c 14
n/c 16
n/c 1
/CODECRES
76
%%oCODECReset%%o
/DSPRES
33
%%oDSPRES%%o
34
MODA/IRQA
MODA/IRQA
35
MODB/IRQB
MODB/IRQB
36
MODC/NMI
MODC/NMI
%%oRAMCS%%o
%%oRAMOE%%o
SPCLK
23
%%oRAMWE%%o SPCLK24
SPMISO
SPMISO25
SPMOSI
SPMOSI26
/HA2
JTAG Port
%%oHA2%%o
HREQ
TRSTB
HREQ27
TMS
GPIO0
TDI
GPIO0 28
GPIO1
TDO
GPIO1 29
FRM8KHz
TCK
GPIO2 31
GPIO3
STM
GPIO3 32
RAMA0
RAMA1
RAMA2
RAMA3
RAMA4
RAMA5
RAMA6
RAMA7
RAMA8
RAMA9
RAMA10
RAMA11
RAMA12
RAMA13
RAMA14
RAMD0
RAMD1
RAMD2
RAMD3
RAMD4
RAMD5
RAMD6
RAMD7
MA3
MA2
MA1
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
2581
C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
VCC
131
125
113
136
134
132
124
121
119
117
115
118
120
128
123
112
116
111
FR0A0
FR0A1
FR0A2
FR0A3
FR0A4
FR0A5
FR0A6
FR0A7
FR0A8
FR0A9
FR0A10
FR0A11
FR0A12
FR0A13
FR0A14
/FR0CS
/FR0OE
/FR0WE
139
141
144
142
140
137
135
133
FR0D0
FR0D1
FR0D2
FR0D3
FR0D4
FR0D5
FR0D6
FR0D7
D
TDI
MA10
MA9
MA8
MA7
MA6
MA5
MA4
TP29
J4
L2
62256
11
12
13
15
16
17
18
19
C
VCC
MA13
MA12
MA11
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
1
VCC
VCC
VCC
/IRQ
/AD0
/AD1
/AD2
/AD3
/AD4
/AD5
/AD6
/AD7
/CE0
/AS--/CE1
/OE--R/W
/WEL--/RST
COM-20
/RES--E
OPTIONAL PIN
A1--AS
A2--A0
ASSIGNEMNTS
A3--A1
A4--A2
A5--A3
XMIT
REC
DGND
DGND
AGND
AGND
+12A
-12A
TALK_AUDIO
AGND
LISTEN_AUDIO
AGND
IC2
D0
D1
D2
D3
D4
D5
D6
D7
20 %%oCS%%o
22 %%oOE%%o
27 %%oWE%%o
RAM
/FR0CS
/FR0OE
/FR0WE
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
10
9
8
7
6
5
4
3
25
24
21
23
2
26
1
FR0A0
FR0A1
FR0A2
FR0A3
FR0A4
FR0A5
FR0A6
FR0A7
FR0A8
FR0A9
FR0A10
FR0A11
FR0A12
FR0A13
FR0A14
B
IC1
710451
6
AVCC 9
QVCC
AVCC 17
QVCC28
SVCC 40
SVCC 48
QVCC53
DVCC 70
8
VCC
PVCC 33
CDSTO13
MSO
VCC 7
19
VCC 22
VCC 42
VCC
VCCIO58
VCC 79
91
VCC 94
VCC
VCC 114
VCCIO130
15 GND
30 GND
50 GND
54 GND
66
87 GND
102 GND
122 GND
GND
126 GND
138 GND
GND
n/c
/C4Out
MA14
DR
MD7
MD6
MD5
MD4
DGND
MD3
MD2
MD1
DVCC
MD0
DGND
GPIO3
GPIO2
GPIO1
GPIO0
/MRD
/MWR
MA17/MRAS
MA16/MCAS
2
3
4
A
GND
MD3
MD2
MD1
MD0
/MRD
/MWR
/MCS0
8
GND
MD7
MD6
MD5
MD4
4
VCCIO
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
AGND
AGND
QGND
AGND
AGND
QGND
SGND
SGND
QGND
SGND
DGND
DGND
GND
1
8
10
15
21
29
34
44
52
54
66
72
CDSTI 12
VDD 28
MS1
7
TDO
5 MS2
14 VSS
GND
2
GND
1
VCCIO
TMS
TRSTB
VD 42
VCC
VA 18
TCK
STM
17 AGND
109
110
RAMA14 111
RAMA12 112
/RAMWE 113
114
115
116
117
118
119
120
121
122
RAMA11 123
RAMA3 124
/RAMOE 125
126
Test6 127
RAMA10 128
Test7 129
130
/RAMCS 131
RAMA2 132
RAMD7 133
RAMA1 134
RAMD6 135
RAMA0 136
RAMD5 137
138
RAMD0 139
RAMD4 140
RAMD1 141
RAMD3 142
143
RAMD2 144
43 DGND
RAMA7
RAMA13
RAMA6
RAMA8
RAMA5
RAMA9
RAMA4
Figure 3-16: COM-20 Communications PCB Rev C
3-27
1
2
3
4
BLANK PAGE
3-28
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
OUT 52/92
IN 2003
M1
S1
1
J1
IC2
TP1
J5
D1
C8
L2
J2
C47
L3
JP1
C27
C1
R3
C2
R6
R4
J4
GND
25
C26
IC5
R46
19
18
IC3
26
R2
R47
+
R1
C6 C41
M4
+
IC4
C5
R49
C37
TP46
C4
TP27
4
+
R42
80
C3
60
R56
C40
TP12
R50
109
IC1
R51
108
R44
61
IC6
C36
144
12
11
5
R55
1
R48
C38
FCL1
C7
T1
R52
C28
R45
IC9
R53
C33
R11
C29
C42
R73
C51
C39
R67
R69
R65
R68
C45
20
R36
C35
R33
41
R37
R38
21
R64
C34
R39
C46
R70
C52
73
36
C10
C44
40
C9
X4
R9
R41
R60
R24
R32 R13
R58
TP21
TP20
GND
TP25
C14
33
22
C21
TP29
C16
R75
C50
+
C49
+ C24
L1
L4
+
23
34
TP24
CLEAR-COM
C11 R18 R22 R17
R35
R16 C12
C25
R43
TP23 TP22
FCL2
R34
C32
R10
C23 R29 R19 C13
R59
72
C31
C43
R62
R54
37
TP14
R63
C18
AGND
IC8
R71
R40
R74
R72
R12
FCL3
C48
12
C22
C20
IC7
M3
C19
ASSY# 710435
R30
+
+ C17
TP3
11
TP4
M2
COM-20
TP18
R25 R26 C15 R27 R28
44
TP5
COPYRIGHT (C) 1999
Figure 3-17: COM-20 Communications PCB Rev.A (part no. 710435)
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
3-29
BILL OF MATERIALS FOR COM-20 COMMUNICATION
PCB (PART NO. 710435)
Capacitors
Designator
3-30
Description
Qty
C14 C22
.001 uF Ceramic Disc SMD 50V 2
1%
C9
.00 33 Ceramic Disc SMD 50V
5%
1
C11 C15 C51
47 pF Ceramic Disc SMD 50V
5%
3
C1
.0015 uF Ceramic Disc SMD
50V 5%
1
C12 C13 C23
.0047 uF Ceramic Disc SMD
50V 10%
3
C2
.022 uF Ceramic Disc SMD 50V 1
10%
C3 C8 C10 C20 C26 C27
.1 uF Ceramic Disc SMD 50V
C28 C29 C31 C32 C33 C34 10%
C35 C36 C37 C38 C39 C40
C41 C42 C43 C44 C45 C46
C47 C48 C49 C50 C52
29
C16 C21
.33 uF Ceramic Disc SMD 25V
10%
2
C4 C5 C6 C17 C18
.47 uF Tantalum SMD 35V 10% 5
C19 C24 C25
10 uF Tantalum SMD 25V 10%
3
C7
100 uF Aluminum 16V 20%
1
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Resistors
Designator
Description
Qty
R16 R22 R34 R35 R36 R40 0 OHM 1/10 SMD
R75
7
R30
2.2 OHM 1/10 SMD 5%
1
R4
47.5 OHM 1/10 SMD 1%
1
R46 R47 R48 R49 R50 R51 221 OHM 1/10 SMD 1%
R52 R53 R54
9
R38
301 OHM 1/10 SMD 1%
1
R3
392 OHM 1/10 SMD 1%
1
R29 R19 R55
604 OHM 1/10 SMD 1%
3
R43 R56 R58 R59 R60 R62 1.00K OHM 1/10 SMD 1%
R63R64 R65 R67 R68 R70
R71 R72 R73 R74 R69
17
R37
2.74K OHM 1/10 SMD 1%
1
R39
3.24K OHM 1/10 SMD 1%
1
R1 R6 R9 R10 R11 R12 R13 4.75K OHM 1/10 SMD 1%
R24 R25 R32
10
R33 R41 R42 R44 R45 R27 4.75K OHM 1/10 SMD 1%
6
R28
4.99K OHM 1/10 SMD 1%
1
R17
7.50K OHM 1/IO SMD 1%
1
R26 R18
75.0K OHM 1/10 SMD 1%
2
Diodes and Transistors
Designator
D1
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Description
Diode BAV99 DUAL DIODE...
SMD
Qty
1
3-31
Integrated Circuits
Designator
Description
Qty
IC2 IC5
62256 CMOS SRAM 32K X 8
2
IC8
6482 DUAL CMOS OPAMP
RAIL/RAIL
2
IC4
0.24MHZ CRYSTAL CLOCK
OSCILLATOR
1
IC7
4218 16-BIT 2 CHANNEL
CODEC
1
IC9
74HCT4046A CMOS PHASE
LOCK LOOP...SOIC16
1
IC3
MT9171AP DIGITAL NETWORK INT
1
IC6
56004 24-BIT DSP 40MHZ
1
IC1
IFPGA DNIC FRAMER, COM
20
1
Miscellaneous
Designator
3-32
Description
Qty
JP1
Connector JUMP JAX
1
JP1(2)
Connector HEADER MULTI PIN 2
HEADER((PER)PIN)
J1
Connector 15 PIN (M) RT ANG 1
PC MTG D TYPE CON
J4
Connector DUAL ROW
HEADER 17 POS. .230IN
J2
Connector RJ-45 RT ANG MOD 1
CON 1-PORT SHIELDED
J5
Connector BNC RT ANGLE PC 1
MNT W/THREAD BUSH
L1 L2 L3
Inductor FERRITE EMI SUPPRESSOR 400MA
S1
Switch DPDT MICRO-SUBMIN- 1
IATURE SWITCH
T1
Transformer 2745B 2:1 PULSE 1
TRANSFORMER
1
3
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
4
SPECIFICATIONS
Note: 0 dBu is referenced to 0.775 V RMS
ICS-102/62
Front-Panel Controls and Connectors
Talk/Listen Switches:
Function Keys
Answer Back Switch
Volume Controls
Headset Connector
Panel Mic Connector
10 (ICS-9102, ICS-102T)
6 (ICS-62, ICS-62T)
2 toggle keys; 4 functions
1
1
1 D4M XLR
1-1/4 inch Phone Jack
Rear-Panel Connectors
Miscellaneous
To Matrix
Audio IO (OPT-100)
DB-15F
DB-15M
DB-15F
Accessory
AC Power
DB-9F
IEC-320
Panel Microphone Input
Type:
Input Level
Impedance
Electret
40 dBv
200 Ohms
Headset Microphone Input
Type
Input Level
Gain Adjustment Range
Impedance
Dynamic
-55dBv
+/- 5dB
200 Ohms
Local Program Input
Type
Impedance
Level
Electronically Balanced
8k Ohms Bridging
0 dBv will produce full
output of speaker when
volume control is fully clockwise
Headphone Outputs
Impedance
Power
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
50 to 600 Ohms
1/2 W into 50 Ohms
4-1
Speaker Amplifier Output
Impedance
Power
8 Ohms
4W
Line Input (2 -pair Listen from Matrix)
Type
Impedance
Level
Freq. Resp.
Transformer Balanced
8k Ohms Bridging
0 dBv nominal
100 Hz to 15 kHz +/- 2 dB
Line Output (2-pair Talk to Matrix)
Type
Impedance
Level
Freq. Resp.
Transformer Balanced
150 Ohms (when talk active)
0 dBv nominal
100 Hz to 15 kHz, +/- 2 dB
Logic Input #1
Type
Logic
5 V logic with pull-up resistor
True = Short to Ground
Logic Input #2
Type (Option 1)
Logic (Option 1)
Type (Option 2)
Logic (Option 2)
5 V logic with pull-up resistor
True = Short to Ground
External Voltage Sense
Lo = 0 - +2 VDC, Hi = +4 - +30 VDC
Mute Relay
Contact Type
Contact Voltage Rating
Contact Current Rating
1 pair SPDT (single form C)
24 VDC
1 Amp continuous, 2 Amps peak at
24 VDC
Station Relay
Contact Type
Contact Voltage Rating
Contact Current Rating
1 pair SPDT (single form C)
24 VDC
1 Amp continuous, 2 Amps peak at
24 VDC
Power
AC Input to Station
Between 12 and 16 VAC at 750 mA
Mains AC
Power Input to Wall-Mount
Transformer 16 W
(150 mA at 115 VAC)
Temperature
Operating
Storage
4-2
Between 0 and 50 C (32 to 125 F)
Between 0 and 70 C (32 to 150 F)
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
Humidity
Operation and Storage
Between 20% and 90%,
Non-Condensing
Package Dimensions
Height
Width
Depth
Weight
1.75 in. (44mm), 1 RU
19.0 in. (483mm)
6.75 in. (171mm)
4.27 lbs. (2.0kg)
OPT-100 AUXILIARY AUDIO I/O OPTION
Audio
Output Signal Levels
Impedance
Frequency Response
Distortion
0.0 dBv nominal
600 Ohms, transformer balanced
100 Hz to 10 kHz, +/- 2 dB of
mic preamp or external program input
Less than 0.5% THD
SA Relay
Contact Type
Contact Voltage Rating
Contact Current Rating
1 pair SPDT (single form C)
24 VDC
1 Amp continuous, 2 Amps peak at
24 VDC
ACCESSORY PANELS
XPL-12
Height
Width
Depth
Weight
Power
1.75 in. (44 mm), (1 RU)
19.0 in. (483 mm)
2.50 in. (64 mm)
1.5 lbs. (0.7 kg)
14 VAC, 0.5 Amps
(120 VAC 770 mA wall-mount
transformer supplied with unit.
220 VAC version available on
special order)
XPL-22
Height
Width
Depth
Weight
Power
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
1.75 in. (44 mm), (1 RU)
19.0 in. (483 mm)
2.50 in. (64 mm)
1.8 lbs. (0.8 kg)
14 V AC, 0.5 Amps
(120 V AC 770 mA
wall-mount transformer
supplied with unit. 220 V AC
version available on special order).
4-3
Notice About Specifications
While Vitec Group Communications makes every attempt to maintain
the accuracy of the information contained in its product manuals, that
information is subject to change without notice. Performance
specifications included in this manual are design-center specifications
and are included for customer guidance and to facilitate system
installation. Actual operating performance may vary.
4-4
Clear-Com Communication Systems
ICS-102/62 Intercom Panel Instruction Manual
5
GLOSSARY
Analog Port Any of the Eclipse matrix’s analog input/output RJ-45
connectors that are used to connect cable from the matrix to panels
and interfaces. Each “port” connects to a separate audio channel in the
matrix intercom system.
Bus A bus is the channel or path between the components in the
matrix along which electrical signals flow to carry information from one
component to the next. In the Eclipse matrix the bus is located in the
etched surface of the midplane.
Call Signal A call signal is an electronic signal sent from one panel or
interface to another. A call signal can be audible and/or visual.
Typically a call signal is sent to get the attention of a panel operator
who may have turned down their intercom speaker’s volume or
removed their headset. It can also be sent to activate an electronic
relay.
Category-5 cable EIA/TIA 568 category specification relating to
network cabling. Shielded category-5 cabling is required for Eclipse
matrix wiring.
CellCom Digital wireless communications product. Sold under the
CellCom name in USA and as FreeSpeak in Europe and Asia.
Central Matrix The term “central matrix” is used to differentiate the
central hardware and software of the intercom system from the
connected audio devices. The central matrix consists of:
1. The metal housing for the circuit cards and power supplies.
2. The circuit cards.
3. The power supplies.
4. The rear panel connectors which connect the matrix’s hardware to
panels and interfaces.
Destination A device such as an intercom panel, beltpack, or interface
to which audio signals are sent. The device from which audio signals
are sent is called a “source”.
Duplex All real-time communication between individuals talking face to
face is full duplex, meaning that they can both talk and listen
simultaneously. The Eclipse Omega matrix provides full-duplex audio.
ECS Eclipse Configuration System. Software program that guides the
operation of the central matrix circuit cards and connected panels.
EMS Element Management System. Software program that is used to
manage the Concert server system resources.
Ethernet International standard which describes how information is
transmitted across a network. Provides for the efficient organization of
network components.
Clear-Com Communication Systems
Eclipse Glossary
5-1
Fiber-optic Cable A fiber-optic cable consists of a glass core covered
with a reflective material called “cladding” and several layers of buffer
coating to protect the cable from the environment. A laser sends light
pulses through the glass core to the other end of the cable.
FreeSpeak Digital wireless communications product. Sold under the
FreeSpeak name in Europe and Asia and CellCom in USA.
Full Duplex Refers to transmission of signals in two directions
simultaneously.
IFB “Interruptible Foldback”. The term “foldback” refers to sending
“program” audio, or some other audio mix, back to announcers while
they are on the air. Doing so allows announcers to monitor
themselves, other announcers, videotapes of commercials, or some
mix of sources, while they on the air. This is typically found in television
news and live broadcast events.
Announcers typically wear a small ear piece so they can hear the
selected foldback audio mix. When a director wants to give directions
to an announcer on air, or to announce changes in the program, the
director must “interrupt” the foldback. To do this, the director uses a
channel specifically set up to interrupt the foldback audio.
Interface Module A piece of electronic hardware designed to convert
the 4-wire signals of a central matrix port to some other form of
communication, such as 2-wire party line, telephone, etc. The interface
module is connected to a central matrix port. The external non-4-wire
device is then connected to the interface module.
ISO The ISO function, short for “panel ISOlation”, allows a panel
operator to call a destination and interrupt all of that destination’s other
audio paths and establish a private conversation. When the call is
completed the destination’s audio pathways are restored to their
original state before the interruption.
IV-R Instant Voice Router. Software that routes digital audio data
between Concert users and between Concert users and Eclipse
systems.
Label A label is an alphanumeric name of up to five characters that
identifies a source, destination, or control function accessed by an
intercom panel. Labels appear in the displays of the intercom panel.
Labels can identify panels, ports interfaced to other external
equipment, fixed groups, party lines, and special control functions.
Mode A term used to describe a light path through a fiber as in
multimode or single mode.
Multimode Fiber-optic Cable The glass core of a multimode fiber is
larger than the core of a single mode fiber, which causes the
transmitted light beam to disperse as it travels through the core. Single
mode fiber, with its smaller core, concentrates the light beam so that it
carries signals further. Multimode fiber was the first type of fiber offered
5-2
Clear-Com Communication Systems
Eclipse Glossary
by manufacturers. Single-mode fiber evolved as production methods
improved.
Multiplexing The process by which two or more signals are
transmitted over a single communications channel. Examples include
time division and wavelength division multiplexing.
Nanometer (nm) Common unit of measure for wavelength. One
billionth of a meter.
Non-volatile Memory Data stored in the CPU’s firmware (ROM) that
is not lost when the power is turned off.
Optical Signal A laser at one end of a fiber-optic cable pulses on or off
to send a light signal through the glass core of the cable to the other
end of the cable. Because the light signals are binary (on or off), the
signal is digital.
Panel Also referred to as “station” in some cases (usually older
manuals). Any intelligent intercom device connected to the rear-panel
analog ports of the central matrix. This term does not refer to devices
connected through interface modules.
Port Any of the input/output connections (RJ-45 connectors) on the
back panel of the central matrix. These connectors and the attached
cables connect the central matrix to remote intercom devices. The
term “port” emphasizes that the connection is a “portal” between the
central matrix and the remote intercom devices.
Program Any separate audio source that is fed into the intercom
channels. In television applications, for example, “program” audio is
the audio that is broadcast on air.
Rack Unit or RU Standardized unit of mounting space on a rack panel.
Each rack unit is 1.75 inches (44.45 mm) of vertical mounting space.
Therefore 1 RU is 1.75 inches (44.45 mm) of vertical mounting space,
2 RU is 3.5 inches (88.9 mm), 3 RU is 5.25 inches (133.35 mm), and
so on.
Remote Panel Any intelligent intercom device connected to the
back-panel ports of the central matrix. This term does not refer to
devices connected through interfaces.
Sidetone The sound of the panel operator’s own voice heard in their
own earphone as they speak.
Single-mode Fiber-optic Cable The glass core of a single-mode fiber
is smaller in diameter than the core of a multimode fiber, so that the
light signal transmitted over the core is more concentrated than with
multimode fiber, which allows the signal to travel further. Single-mode
fiber evolved from multimode fiber as production methods improved.
Source In this manual, the term “source” refers to a device—such as
an intercom panel, interface, or beltpack —that sends audio into the
matrix. The device to which audio is sent is called a “destination”.
Clear-Com Communication Systems
Eclipse Glossary
5-3
VOX In the Eclipse system, when audio at a panel exceeds a
threshold, a light switches on at the panel’s port card to visually cue the
operator. The threshold level is set in the Eclipse Configuration
Software.
V-Series Communications panels used with Eclipse systems providing
advanced facilities. Available in rack mount and desktop formats.
Wavelength-division Multiplexing (WDM) A method of multiplexing
optical signals developed for use on fiber-optic cable. Each signal is
assigned a particular wavelength on the light spectrum and therefore
many signals can be transmitted simultaneously without interfering
with each other.
5-4
Clear-Com Communication Systems
Eclipse Glossary
ECLIPSE MANUALS
The following manuals are available covering Eclipse products and
accessories.
SOFTWARE MANUALS
Eclipse Configuration System (ECS) Instruction Manual - 810299Z
Eclipse Logic Maestro Instruction Manual - 810414Z
Eclipse Production Maestro Quick Start Guide - 810409Z
Eclipse Production Maestro Installation and User Guide - 810410Z
Eclipse DECTSync Manual - 810412Z
Eclipse Host Computer Interface (HCI) Manual - 810413Z
HARDWARE MANUALS
Eclipse Omega Matrix Instruction Manual - 810290Z
Eclipse Median Matrix Instruction Manual - 810347Z
Eclipse PiCo Matrix Instruction Manual - 810348Z
Eclipse-32 Matrix Instruction Manual - 810315Z
Eclipse Matrix Installation Manual - 810298Z
Eclipse Upgrade Reference Manual - 810377Z
Eclipse V-Series Panels User Manual - 810365Z
Eclipse FOR-22 4-Wire Interface Instruction Manual - 810306Z
Eclipse CCI-22 Party Line Interface Instruction Manual - 810307Z
Eclipse TEL-14 Telephone Interface Instruction Manual - 810308Z
Eclipse GPI-6 General Purpose Inputs Instruction Manual - 810309Z
Eclipse RLY-6 General Purpose Outputs Instruction Manual - 810310Z
DIG-2 Digital Interface Instruction Manual - 810311Z
IMF-3, IMF-102, DIF-102 Interface Module Frame Instruction Manual 810313Z
Eclipse AES-6 Digital Interface Instruction Manual - 810383Z
Eclipse BAL-8 Isolation Interface Instruction Manual - 810403Z
Eclipse V-Series AES-3 Option Card Installation Instructions 810388Z
Eclipse V-Series XLR-7M Upgrade Instructions - 810405Z
Eclipse V-Series T-Adapter Installation Instructions - 810406Z
Eclipse FIM-202D Fiber Interface Instruction Manual - 810385Z
Clear-Com Communication Systems
Eclipse Manuals
5-5
Eclipse FIM-102 Fiber Interface Instruction Manual - 810319Z
Eclipse FIM-108 Fiber Interface Instruction Manual - 810291Z
Eclipse 4000 Series II Panels Installation Guide - STA0530Z
Eclipse 4000 Series II Panels User Guide - STA0531Z
Eclipse ICS 1008E/1016E Panels Instruction Manual - 810404Z
Eclipse ICS 102/62 Panels Instruction Manual - 810302Z
Eclipse ICS 2003 Panel Instruction Manual 810303Z
Eclipse ICS 92/52 Panels Instruction Manual - 810301Z
Eclipse i-Station Instruction Manual - 810305Z
Eclipse ICS-21 Speaker Panel Instruction Manual - 810263Z
Eclipse ICS-22 Speaker Panel Instruction Manual - 810264Z
Eclipse ICS-24 Headset Panel Instruction Manual - 810265Z
Eclipse Digital Wireless Beltpack Instruction Manual - 810376Z
5-6
Clear-Com Communication Systems
Eclipse Manuals
LIMITED WARRANTY
This document details the Clear-Com Standard Limited Warranty for all new products for sale within all
regions with the exception of Military, Aerospace, and Government (MAG).
EXCEPT AS SET FORTH HEREIN ("LIMITED WARRANTY"), CLEAR-COM MAKES NO OTHER
WARRANTIES, EXPRESS, IMPLIED OR STATUTORY, INCLUDING WITHOUT LIMITATION ANY
WARRANTIES OF MERCHANTABILITY, NONINFRINGEMENT OF THIRD PARTY RIGHTS, OR
FITNESS FOR A PARTICULAR PURPOSE, ALL OF WHICH ARE EXPRESSLY DISCLAIMED.
1. Standard Limited Warranty. Clear-Com Communication Systems ("Clear-Com") warrants its
products, including supplied accessories, against defects in material or workmanship for the time
periods as set forth below provided it was purchased from an authorized Clear-Com dealer or
distributor.
a) Pursuant to this Limited Warranty, Clear-Com will, at its option:
i)
repair the product using new or refurbished parts, or;
ii) replace the product with a new or refurbished product.
b) Remedies: In the event of a defect, the rights detailed in 1 (a) are your exclusive remedies. For
purposes of this Limited Warranty, "refurbished" means a product or part that has been returned
to its original specifications.
c) Standard Warranty Period (by Product):
i)
All Clear-Com brand systems and products, including belt packs, have a Limited Warranty
of two years, with the exception of;
(1) Cables, accessories, components & consumable items have a Limited Warranty of 90
days.
(2) Any Clear-Com product that has been classified as obsolete at the time of sale has a
Limited Warranty of 90 days from sales and will be replaced with the same product or a
sales credit will be issued, at the sole discretion of Clear-Com.
(3) Headsets, handsets, microphones, and associated spare parts, as well as UHF wireless
IFB products, have a Limited Warranty of one year.
(4) UHF WBS Analog wireless intercom systems have a Limited Warranty of three years.
Clear-Com Communication Systems
Standard Limited Warranty
i
(5) All software products, including Concert (Client and Server), ECS, Production Maestro
and Logic Maestro are warranted for one year and shall substantially conform to
published specifications. The media on which the Software is furnished is warranted to
be free of defects in material and workmanship (under normal use) for a period of one
year.
(6) Any Clear-Com products that are listed within the last time buy period have the same
Limited Warranty for their type 1.i 1 - 1.i.5 as above.
d) Any Clear-Com product that is repaired or supplied as a replacement under the terms of this
Limited Warranty shall inherit the remaining warranty period from the original product.
e) Standard Warranty Period Start Date
i)
Dealer / Distributor Sales: In view of Dealer or Distributor stocking practices, the Standard
Warranty Period for products sold through Dealers or Distributors will commence from the
Clear-Com invoice date and will include an automatic extension of three months. Any valid
warranty claim within the Standard Warranty Period as determined by the Clear-Com
invoice date will be covered without further supporting evidence. All warranty claims after
this date must be supported by the Customer's proof of purchase that demonstrates the
product is still within the Standard Warranty Period (as detailed in Section 1.c.i above, plus
the automatic three month extension) from their purchase date.
ii) Direct Sales: The Standard Warranty Period will commence from the date the product was
shipped from Clear-Com to the Customer. The Standard Warranty Period start date for
contracts that include commissioning will be the date of the Site Acceptance Test (SAT) or
one month from conclusion of the commissioning project, whichever is earlier.
f) Invalidation of Warranty
i)
This Limited Warranty shall be invalidated if the product's outer case has been opened and
internal modifications have been made or damage has occurred, or upon the occurrence of
other damage or failure not attributable to normal wear and tear. Authorized modifications
with Clear-Com's express written permission will not invalidate the warranty.
g) Software Updates
i)
ii
Software Updates are released periodically to correct discovered program bugs. During the
Warranty Period, software updates are available to Customers free of charge.
Clear-Com Communication Systems
Standard Limited Warranty
h) Software Upgrades
i)
Software Upgrades include new Features and/or Functional Enhancements and are not
included as part of the Standard Warranty but may be purchased at the published rates.
ii) Note: In the absence of a Software Update containing a program correction and no
available workaround to mitigate the problem, at the discretion of Service, Sales,
Engineering, or Product Management, the Customer may be provided a Software Upgrade
under warranty.
2. Exclusions. Services do not cover damage or failure caused by any occurrence beyond Clear-Com's
reasonable control, including without limitation acts of God, fire, flooding, earthquake, lightning, failure
of electric power or air conditioning, neglect, misuse, improper operation, war, government
regulations, supply shortages, riots, sabotage, terrorism, unauthorized modifications or repair, strikes,
labor disputes or any product failure that Clear-Com determines is not a result of failure in the
Services provided by Clear-Com. Further Services excluded from this Agreement include: services
required due to errors or omissions in Customer purchase orders; installation or maintenance of
wiring, circuits, electrical conduits or devices external to the products; replacement or reconditioning
of products which, in Clear-Com's opinion cannot be reliably maintained or properly serviced due to
excessive wear or deterioration; Customer's failure to maintain the installation site in accordance with
the environmental specifications of the products; or service on products removed from the location
originally specified by Customer and/or reinstalled without the prior written approval of Clear-Com.
Customer will pay Clear-Com's then current published charges to restore such Covered Products to a
condition eligible for further service under this Agreement. Clear-Com shall be excused from and shall
not be liable for any failure or delay in performance under this Agreement due to the foregoing or any
causes beyond its reasonable control.
3. Limitation of Liability. IN NO EVENT WILL CLEAR-COM BE LIABLE UNDER THIS AGREEMENT
FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING
WITHOUT LIMITATION LOST PROFITS), REGARDLESS OF THE FORM OF ACTION, EVEN IF
ADVISED IN ADVANCE OF THE POSSIBILITY OF SUCH DAMAGES.
4. Assignment. Neither party may assign this Agreement or any portion thereof without the prior written
consent of the other, except in the event of a merger, sale of all or substantially all of the assets or
other corporate reorganization.
5. Ownership of replaced parts or product. All replaced parts or products become the property of
Clear-Com.
6. Entire Agreement. This Agreement constitutes the entire agreement between the parties with
respect to the subject matter hereof, and supersedes all prior or contemporaneous proposals, oral or
written, and all other communications between them relating to the subject matter of this Agreement.
Clear-Com Communication Systems
Standard Limited Warranty
iii
iv
Clear-Com Communication Systems
Standard Limited Warranty
TECHNICAL SUPPORT & REPAIR POLICY
NOVEMBER 1, 2008
In order to ensure that your experience with Clear-Com and our World Class products is as beneficial,
effective and efficient as possible, we would like to define the policies and share some "best practices"
that can accelerate any problem solving processes which we may find necessary and to enhance your
customer service experience. Our Technical Support, Return Material Authorization, and Repair Policies
are set forth below. These Policies are subject to revision and constantly evolve in order to address our
Customers' and the Market's needs. Accordingly these are provided by way of guidance and for
information only and may be changed at anytime with or without Notice.
TECHNICAL SUPPORT POLICY
a) Telephone, online, and e-mail technical support will be provided by the Customer Service Center
free of charge during the Warranty Period.
b) Technical support will be provided free of charge for all software products under the following
conditions:
i)
The application, operating, and embedded software is installed on a product covered by
Clear-Com's Limited Warranty, and:
(1) The software is at the current release level; or,
(2) The software is one (1) version removed from current.
ii) Older versions of software will receive "best-effort" support, but will not be updated to
correct reported bugs or add requested functionality.
c) For Technical Support:
i)
North and South America, (inc. Canada, Mexico, and the Caribbean) & US Military:
Hours:
0800 - 1700 Pacific Time
Days:
Monday - Friday
Tel:
+1 510 337 6600
Email:
[email protected]
ii) Europe, the Middle East and Africa:
Hours:
0800 - midnight Central European Time
Clear-Com Communication Systems
Technical Support & Repair Policy
v
Days:
Tel:
Email:
iii) Asia-Pacific:
Hours:
Days:
Tel:
Email:
Monday - Friday
+49 40 853 999 700
[email protected]
0800 - 1700 Pacific Time
Monday - Friday
+1 510 337 6600
[email protected]
d) Email Technical Support is available for all Clear-Com branded products free of charge for the life
of the product, or two years after a product has been classified as obsolete, whichever comes
first.
e) Support for Distributor and Dealer Sales
i)
Distributors and Dealers may utilize the Customer Service Centers once a system has been
installed and commissioned. Clear-Com Systems and Applications Engineers will provide
support to the Distributor from the pre-sales stage through to satisfactory installation for new
system purchases. Customers will be encouraged to contact their Dealer or Distributor with
their installation and technical support enquires rather than using the Customer Service
Centers directly.
f) Support for Direct Sales
i)
Customers may utilize the Customer Service Centers once a system has been installed and
commissioned by Clear-Com Systems and Applications Engineers, or in the case of project
installations, once the Project Team has completed the hand-over to the Support Centers.
RETURN MATERIAL AUTHORIZATION POLICY
a) Authorizations: All products returned to Clear-Com or a Clear-Com Authorized Service Partner
must be identified by a Return Material Authorization (RMA) number.
b) The Customer will be provided with an RMA number upon contacting Clear-Com Sales Support
as instructed below.
c) The RMA number must be obtained from Clear-Com via phone or email prior to returning product
to the Service Center. Product received by the Service Center without a proper RMA number is
subject to return to the Customer at the Customer's expense.
vi
Clear-Com Communication Systems
Technical Support & Repair Policy
d) Damaged equipment will be repaired at the Customer's expense.
e) Returns are subject to a 15% restocking fee.
f) Advance Warranty Replacements (AWRs);
i)
During the first 30 days of the Standard Warranty Period: Once the equipment fault has
been verified by Clear-Com or its authorized representative, Clear-Com will ship a new
replacement product. The Customer will be provided with an RMA number and be required
to return the faulty equipment within 14 days of receipt of the replacement or will be invoiced
for the list price of a new product.
ii) During days 31-90 of the Standard Warranty Period: Once the equipment fault has been
verified by Clear-Com or its authorized representative, Clear-Com will ship a like-new, fully
refurbished replacement product. The Customer will be provided with an RMA number and
be required to return the faulty equipment within 14 days of receipt of the replacement or will
be invoiced for the list price of a new product.
iii) To obtain an RMA number or request an AWR:
(1) North and South America, Asia-Pacific, and US Military:
Hours:
0800 - 1700 Pacific Time
Days:
Monday - Friday
Tel:
+1 510 337 6600
Email:
[email protected]
(2) Europe, the Middle East and Africa:
Hours:
0800 - 1700 GMT + 1
Days:
Monday - Friday
Tel:
+ 44 1223 815000
Email:
[email protected]
iv) Note: AWRs are not available for UHF WBS Analog wireless intercom systems. UHF WBS
Analog wireless intercom systems out-of-box failures must be returned to Alameda for
repair.
v) Note: Out-of-box failures returned after 90 days will be repaired and not replaced unless
approved by Clear-Com Management.
vi) Note: AWRs are not available after 90 days of receipt of product unless an AWR Warranty
Extension is purchased at the time of product purchase.
Clear-Com Communication Systems
Technical Support & Repair Policy
vii
vii) Note: Shipping charges, including duties, taxes, and insurance (optional), to Clear-Com's
factory is the responsibility of the Customer. Shipping AWRs from Clear-Com is at
Clear-Com's expense (normal ground or international economy delivery). Requests for
expedited shipping (E.g. "Next-Day Air") and insurance are the responsibility of the
Customer.
REPAIR POLICY
a) Repair Authorizations: All products sent to Clear-Com or a Clear-Com Authorized Service Partner
for repair must be identified by a Repair Authorization (RA) number (see above).
b) The Customer will be provided with an RA number upon contacting Clear-Com Customer
Services as instructed below.
c) The RA number must be obtained from Clear-Com via phone or email prior to returning product to
the Service Center. Product received by the Service Center without a proper RA number is
subject to return to the Customer at the Customer's expense.
d) Return for Repair
i)
Customers are required to ship equipment at their own cost (including transportation,
packing, transit, insurance, taxes and duties) to Clear-Com's designated location for repair.
(1) Clear-Com will pay for the equipment to be returned to the Customer when it is repaired
under warranty.
(2) Shipping from Clear-Com is normal ground delivery or international economy.
Requests for expedited shipping (E.g. "Next-Day Air") and insurance are the
responsibility of the Customer.
ii) Clear-Com does not provide temporary replacement equipment ("loaner") during the
period the product is at the factory for repair. Customers should consider a potential
prolonged outage during the repair cycle, and if required for continuous operations
purchase minimum spare equipment required or purchase an AWR Warranty Extension.
iii) No individual parts or subassemblies will be provided under warranty, and warranty repairs
will be completed only by Clear-Com or its Authorized Service Partners.
iv) Customers requesting a non-warranty repair will be provided an estimate of the total repair
cost prior to the return of the equipment. In the event that Clear-Com is unable to estimate
viii
Clear-Com Communication Systems
Technical Support & Repair Policy
the cost of repair, the Customer may elect to return the product to the factory for an
estimate. The Customer is responsible for shipping costs both to and from the factory in the
event they choose not to accept the estimate.
v) The Customer must provide either a purchase order for the repair work, or will be required
to make an advance payment (as a debit against the Dealer's line of credit, or credit card)
prior to the repaired product being returned to the Customer.
vi) For requesting a Repair Authorization number:
(1) North and South America, Asia-Pacific, and US Military:
Hours:
0800 - 1700 Pacific Time
Days:
Monday - Friday
Tel:
+1 510 337 6600
Email:
[email protected]
(2) Europe, the Middle East and Africa:
Hours:
0800 - midnight Central European Time
Days:
Monday - Friday
Tel:
+49 40 853 999 700
Email:
[email protected]
vii) Note: Clear-Com's Limited Warranty does not cover normal wear and tear. The Customer
will be charged the full cost of the repair if their equipment has been tampered with by
non-approved personnel, or has been subject to damage through electrical failure, liquid
damage or mishandling. The Customer Service Center will provide the Customer with a
cost estimate for any such repairs prior to undertaking the work.
Clear-Com Communication Systems
Technical Support & Repair Policy
ix
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement