Waxess | DM1000 | User guide | Waxess DM1000 User guide

Waxess DM1000 User guide
DM1000 CB GSM.book Page i Sunday, July 11, 2010 10:24 PM
Waxess USA, Inc.
DM1000
User Guide
DM1000 CB GSM.book Page ii Sunday, July 11, 2010 10:24 PM
Handset
1
Antenna
2
Betlclip attachment
3
Speaker for Ringer
4
Handset battery compartment
5
New Message LED
6
Handset Earpiece
7
LCD Display
8
Function Keys
9
Up/Down keys
10 Menu and Off keys
11
*
Scroll Left
12 Flash/Delete key
13 Redial/Pause key
14 Headset Jack
15 #
Scroll Right
16 Intercom
17 Handset Microphone
18 Handset Charging Contacts
DM1000
ii
Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page iii Sunday, July 11, 2010 10:24 PM
Base
19 Base Speaker/Ringer
20 LCD Display
21 Function Keys
22 Up/Down Keys
23 Menu and Off Keys
24 Intercom Key
25 Speaker Phone Key
26 Speaker Phone ON LED
27 Redial/Pause Key
28 New Message LED
29 Flash Key
30 DC IN 9V Jack
31 TEL LINE Jack
32 Corded Handset Jack
34
33 Battery cover
34 SIM Card Access Cover
DM1000
iii
Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page iv Sunday, July 11, 2010 10:24 PM
Notes
DM1000
iv
Copyright © 2010 Waxess USA
DM1000 CB GSMTOC.fm Page v Sunday, July 11, 2010 10:26 PM
Contents
Get ready . . . . . . . . . . . . . . . . . . . . . . 1
About the SIM card . . . . . . . . . . . . .
Install the SIM card . . . . . . . . . . .
Choose Location . . . . . . . . . . . . . . .
Desk or Table . . . . . . . . . . . . . . .
Wall mount . . . . . . . . . . . . . . . . .
Base power on . . . . . . . . . . . . . . .
Power backup batteries (Optional)
Standby Screen . . . . . . . . . . . . . .
Signal level meter . . . . . . . . . . . .
Ready the cordless handset . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1
2
3
3
4
5
5
7
8
9
Get set . . . . . . . . . . . . . . . . . . . . . . . 12
Dialing mode . . . . . . . .
Time and date . . . . . . .
Set the ringer tone . . . .
Set the ringer volume .
Key beep . . . . . . . . . . .
Area codes . . . . . . . . . .
Add/remove a 1 . . . . .
Add/remove area code
Language . . . . . . . . . . .
LCD contrast . . . . . . . .
Name . . . . . . . . . . . . .
Handset registration . . .
Register . . . . . . . . . .
Deregister . . . . . . . . .
DM1000
v
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
12
13
14
15
17
17
18
18
19
19
20
20
20
21
Copyright © 2010 Waxess USA
DM1000 CB GSMTOC.fm Page vi Sunday, July 11, 2010 10:26 PM
GO! . . . . . . . . . . . . . . . . . . . . . . . . . 22
Make a wireless call . . . . . . . .
Make a landline call . . . . . . . . .
Set earpiece volume . . . . . . .
Calling options . . . . . . . . . . . .
Speed dial . . . . . . . . . . . . . .
Redial . . . . . . . . . . . . . . . . .
Pause (for TEL line use only) .
Answer a wireless call . . . . . . .
Answer a landline call . . . . . . .
In-Call operations . . . . . . . . . .
Place a call on Hold . . . . . . .
Mute a call . . . . . . . . . . . . .
Transfer a call . . . . . . . . . . .
Set up a conference call . . . .
Phone book . . . . . . . . . . . . . .
Enter names and characters .
Enter numbers directly . . . . .
Edit names or numbers . . . . .
Enter numbers from Caller ID
Call from phone book . . . . . .
Speed dial . . . . . . . . . . . . . .
Messages . . . . . . . . . . . . . . . .
Voice messages . . . . . . . . . .
Short Message Service (SMS)
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
22
23
23
24
24
24
25
25
26
27
27
27
27
30
31
31
32
33
33
35
35
35
36
37
More features . . . . . . . . . . . . . . . . . . 43
Caller ID . . . . . . . . . .
Caller ID information
Check the log . . . . .
Dial a number . . . . .
DM1000
vi
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
43
43
45
45
Copyright © 2010 Waxess USA
DM1000 CB GSMTOC.fm Page vii Sunday, July 11, 2010 10:26 PM
Save a number . . . . . . . .
Delete a number . . . . . . .
Call Forwarding . . . . . . . . . .
Activate Call Forwarding . .
Deactivate Call Forwarding
Page and Intercom . . . . . . .
Page . . . . . . . . . . . . . . . .
Intercom . . . . . . . . . . . . .
Two-line calling . . . . . . . . . .
Quick reference chart . . . .
Make two separate calls . .
Receive two separate calls
Call waiting with two calls .
Barge-in . . . . . . . . . . . . . .
Quick reference chart . . . .
Set up Barge-In . . . . . . . .
Use Barge-In . . . . . . . . . .
Cellular only . . . . . . . . . . . .
Set up Cellular only . . . . .
Turn off Cellular only . . . .
CEL Phone Number . . . . . . .
Power back-up . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
45
46
47
47
48
48
48
49
50
51
52
52
53
53
55
56
56
57
57
57
58
58
Precautions . . . . . . . . . . . . . . . . . . . . 60
Rechargeable Nickel-Metal-Hydride Battery
Warning . . . . . . . . . . . . . . . . . . . . . . . . 60
Rechargeable Nickel-Metal-Hydride Batteries
Must Be Recycled or Disposed of Properly
61
Important safety instructions . . . . . . . . . . . 61
Important Electrical Considerations . . . . . 64
The FCC Wants You To Know . . . . . . . . . . 65
DM1000
vii
Copyright © 2010 Waxess USA
DM1000 CB GSMTOC.fm Page viii Sunday, July 11, 2010 10:26 PM
Range . . . . . . . . . . . . . . . . . . .
Telephone Line Problems . . . . .
Radio Interference . . . . . . . . . .
Cordless Telephone Privacy . . . .
Installation Considerations . . . .
Telephone Line Outlets . . . . . . .
Connecting the Telephone Cords
Applying Power to the base . . . .
I.C. Notice . . . . . . . . . . . . . . . . .
RADIO EQUIPMENT . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
66
66
67
68
68
69
70
70
71
72
General information . . . . . . . . . . . . . . 73
DM1000 Menu map . . . . . . . . . . . . . . 74
DM1000
viii
Copyright © 2010 Waxess USA
DM1000 CB GSMTOC.fm Page ix Sunday, July 11, 2010 10:26 PM
Notes:
DM1000
ix
Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 1 Sunday, July 11, 2010 10:28 PM
Get ready
1 Get ready
1
Included items
• Base
• Belt clip
• Cordless handset
• Wall mount bracket
• AC adaptor for base
• Telephone cord
• AC adaptor for
cordless handset
• User guide
• Rechargeable battery
for cordless handset
•About the SIM card
This phone connects to GSM networks through a
Subscriber Identity Module card that you get from
your cellular service provider. The SIM card carries
information about your wireless account.
Some important considerations:
• Keep all SIM cards out of the reach of small children.
• The SIM card and its contacts are easily damaged
by scratches or bending, so be careful when
handling, inserting, or removing the card.
• Disconnect power and remove batteries from
the phone before removing or inserting the SIM
card.
DM1000
1
Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 2 Sunday, July 11, 2010 10:28 PM
1
Install the SIM card
1 Important: Verify power is disconnected
from the base.
2 Turn the Base Unit over and open the SIM card
cover.
3 Align the
SIM card
with the
beveled
corner
facing
right, gold
contact
area facing
downward.
4 Carefully slide in the SIM card until the flat edge
contacts the end of the receptacle.
Also, refer to the diagram on the SIM
Compartment cover.
5 Replace the cover.
DM1000
2
Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 3 Sunday, July 11, 2010 10:28 PM
Get ready
•Choose Location
Some important considerations:
• Charge the handset for 12–15 hours before use it.
• Locate the base near both a phone jack and a
power outlet which is not controlled by a switch.
• Keep the base and handset away from sources of
electrical noise, such as motors and fluorescent
lighting.
• Leave enough room to raise both base antennas
fully vertical.
Desk or Table
To AC outlet
To telephone
outlet
1 Connect the telephone line cord to the TEL LINE
jack and to a telephone jack.
2 Set the base on a desk or table and place the
handset on the base.
DM1000
3
Copyright © 2010 Waxess USA
1
DM1000 CB GSM.book Page 4 Sunday, July 11, 2010 10:28 PM
1
3 Connect the handset cord to the jacks on the
handset and the base, then set the handset in
the cradle.
4 Raise both antennas to a vertical position.
5 Find the base AC adaptor (the larger adaptor),
and connect it to the DC IN 9V jack and to a
standard 120V AC.
Wall mount
1 Attach the wall mount adaptor to the base.
2 Find the base AC adaptor (the larger adaptor),
plug the connector into the DC IN 9V jack, then
plug the telephone line cord to the TEL LINE
jack.
3 Wrap the AC adaptor inside the molded wiring
channel, then wrap the cord around the strain
relief notch.
4 Raise the antennas to a vertical position.
DM1000
4
Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 5 Sunday, July 11, 2010 10:28 PM
Get ready
5 Align the mounting slots on the base with the
mounting posts on the wall plate. Then push in
and down until the phone is firmly seated.
6 Connect the handset cord to the jacks on the
handset and base, then set the corded handset
in the cradle.
7 On the base, remove the handset retainer, flip it
over, then replace it.
Base power on
When powered on for the first
time, the base goes through an
initialization sequence.
Note: Do not use the phone
until the initialization
sequence is complete.
Power backup
batteries (Optional)
The optional back-up batteries provide a reserve
power supply so the base can operate for up to 30
minutes (depending on battery condition) in case of
power outages or if power is cut off to the base for
any reason. Backup power activates immediately
when the normal power supply to the base is cut off.
1 Verify power is disconnected from the base.
2 Open the battery cover on the bottom of the
DM1000
5
Copyright © 2010 Waxess USA
1
DM1000 CB GSM.book Page 6 Sunday, July 11, 2010 10:28 PM
1
base.
3 Insert five AA alkaline
batteries with the
polarity (+ and -)
aligned as marked in the
compartment.
4 Replace the cover.
Note:
• Batteries are not included
• Batteries are not required to operate the product
• There is no indication that shows when the base is
operating with normal power or back-up power
• If you choose to install back-up batteries, check
the power level frequently (see “Power back-up”
on page 58). Replace the batteries when the
power level is less than half of maximum
• After any power outage, check the battery power
level and replace batteries as needed
• The battery power comes on automatically when
DM1000
6
Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 7 Sunday, July 11, 2010 10:28 PM
Get ready
current from the AC adaptor is interrupted;
unplugging the AC adaptor does not turn off power
to the phone
• Be sure to remove at least one battery when
disconnecting power
• The Battery Level indicator on the base menu
screen may not show true battery condition unless
all five batteries are installed
Caution: Use only AA alkaline batteries for power
backup. Do not use rechargeable
batteries. The battery compartment
circuitry is not designed to recharge
batteries.
Standby Screen
When the sequence is complete,
the Standby Screen appears.
This screen appears on both the
base and the handset, and is
always visible when the phone is
idle. At the bottom of the screen, the text indicates
which service lines are active. CEL is wireless
service, and TEL is landline service.
The CEL indicator may take up to two minutes to
appear, depending on cellular signal conditions in
your area.
DM1000
7
Copyright © 2010 Waxess USA
1
DM1000 CB GSM.book Page 8 Sunday, July 11, 2010 10:28 PM
1
If you have connected with your cellular service
provider, the date and time may be set
automatically. If not, see “Time and date” on page
13 to set the date and time manually.
Signal level meter
The Signal Level feature helps
you find your strongest cellular
service signal. Move the base
around your location to find the
strongest signal level.
Be sure the CEL indicator is shown in the
display before checking the signal level.
DM1000
8
Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 9 Sunday, July 11, 2010 10:28 PM
Get ready
Ready the cordless handset
INSTALL THE BATTERY
1 Open the cover.
2 Verify that the
connector is
properly
aligned with
the jack and
connect the
battery.
Note: The
connector
is
designed to easily fit the jack in only one
direction. Do not use excessive force.
3 Close the cover.
DM1000
9
Copyright © 2010 Waxess USA
1
DM1000 CB GSM.book Page 10 Sunday, July 11, 2010 10:28 PM
1
CHARGE THE
BATTERY
To AC outlet
1 Find the cordless
handset AC
Adaptor (the
smaller adaptor,
Model number
HKD090050U).
Connect the AC adaptor to the DC 9V IN jack on
the charger and to a standard 120V AC wall
outlet.
2 Set the charger on a desk or table, then set the
handset in the charger with the keypad facing
forward.
3 Allow the battery to charge for
12–15 hours.
Note: Charge the battery
frequently. Leaving the
battery uncharged for a
prolonged period can
adversely affect battery
charging capacity. If this
happens, replace the battery.
DM1000
10 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 11 Sunday, July 11, 2010 10:28 PM
Get ready
A power indicator in the upper
right corner of the LCD shows
how much battery life remains.
09:00A 01/01
New: 00
Total: 00
HANDSET - 1
CEL
TEL
Full charge
Low charge
Note: Use only the rechargeable battery pack
supplied with your cordless handset.
DM1000
11 Copyright © 2010 Waxess USA
1
DM1000 CB GSM.book Page 12 Sunday, July 11, 2010 10:28 PM
2 Get set
•Dialing mode
2
1 Press the MENU key on the
base.
The Menu appears.
2 Press the
Setup.
key so the highlight bar moves to
3 +Press F1 to “select” this menu item.
This action is called “Press Select”
throughout this guide.
Another menu list appears.
4 Press the
key and scroll to Tone/Pulse.
5 Press F1 to select this item
and this screen appears.
Highlight the correct setting for your phone
system, then press F1 to enter the setting in
memory.
A beep confirms the setting, and the Setup
menu appears.
6 Press EXIT to return to the main menu screen.
OR
DM1000
12 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 13 Sunday, July 11, 2010 10:28 PM
Get set
Press EXIT twice or OFF to return to Standby.
The following steps apply to both the base and the
handset.
2
•Time and date
The time and date automatically synchronizes with
the cellular network once when the base is powered
on (if supported by your service provider). If the
time and date do not automatically synchronize
with the network afterward it must be set manually.
1 Press MENU.
2 Use the
/
keys and scroll to Time and Date.
3 Press Select.
A cursor blinks on the hour
number.
4 Use the keypad to enter the
correct hour.
The cursor moves to the right for the minute
numbers.
5 Enter the correct minutes, and press OK.
The AM/PM screen appears.
6 Use the
or
key to set AM or PM and press
OK.
The time format setting appears.
or
7 Use the
press OK.
DM1000
key to set the time format and
13 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 14 Sunday, July 11, 2010 10:28 PM
2
The date screen appears with months showing.
8 Use the keypad to enter the correct month.
After entering the month, the cursor moves to
the day.
9 Enter the correct day then press OK.
The cursor appears on the first digit of the
current year setting.
10Use the keypad to enter the four digits for the
correct year and press OK
The date format appears.
11Press
or
to select a format and press OK.
You hear a confirmation tone and the Main
menu appears.
When the time and date are set on the base or on
one of the cordless handsets, the time and date for
all other components (handset or base)
automatically synchronize after a few minutes. If a
new cordless handset is added and properly
registered, the time and date for the new handset
will automatically synchronize.
•Set the ringer tone
You can set different ring tones for CEL (wireless)
calls and TEL (landline) calls.
1 Press MENU.
2 Scroll to Ringer/Key Beep, and press Select.
DM1000
14 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 15 Sunday, July 11, 2010 10:28 PM
Get set
3 Scroll to Ringer Tone, and press Select.
The ringer tone menu for CEL calls appears
first. The current ringer tone is highlighted.
The base has three ring tones available. The
handset has six rings available—three tones
and three melodies.
Note: Melodies are only available on the cordless
handset.
4 Scroll through the list of tones.
Pause on a tone name to hear a short sample of
the tone. The sample plays two seconds for a
ring tone and 10 seconds for a melody.
5 Press Select.
The TEL Ring Tone setting appears.
OR
Press Exit to cancel without saving changes.
6 Follow steps 1–4 above to choose a tone, and
press Select.
A confirmation tone plays.
Set the ringer volume
You can set the ringer volume from menu. The
choices are
Off-Low-Medium-High.
1 Press MENU, scroll to Ringer/Key Beep, and
press Select.
2 Scroll to Ringer volume, and press Select.
DM1000
15 Copyright © 2010 Waxess USA
2
DM1000 CB GSM.book Page 16 Sunday, July 11, 2010 10:28 PM
2
The current ring volume setting is highlighted.
3 Scroll to a volume setting. Each time you stop
on a setting a sample plays briefly.
4 Scroll to the ring volume you want and press
Select.
A confirmation tone plays and the Ringer/Key
beep menu appears.
5 Press Exit or OFF to return to the Standby screen.
NIGHT VOLUME
You can set the volume for the ringer to a lower
level for night time between 9 p.m. and 6 a.m.
based on the phone’s internal clock.
1 Press MENU, scroll to Ringer/Key Beep, and
press Select.
2 Scroll to Night Volume and press Select.
or
key to change the volume
3 Use the
setting.
A sample of the volume level plays when you
move the cursor. The sample plays two seconds
for each ringer tone and 10 seconds for each
melody.
4 Press Select to set the ringer. A tone confirms
the setting.
DM1000
16 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 17 Sunday, July 11, 2010 10:28 PM
Get set
•Key beep
Set the phone so that you hear a beep each time
you press a button, or turn off the beep feature.
1 Press MENU, scroll to Ringer/Key Beep, and
press Select.
2 Scroll to Key beep, press Select, then choose
On or Off.
3 Press OK to enter the setting.
A tone confirms the setting and the Ringer/Key
beep menu appears.
•Area codes
Enter up to three area codes.
With local area codes stored, the
phone can distinguish between
local and long distance calls.
1 Press MENU.
Area Code
Area Code
Area Code
Area Code
EXIT
2 Scroll to Setup, then press Select.
3 Scroll to Area Code, and press Select.
4 Use the keypad to enter the area code number,
then press OK.
If you make a mistake, press FLASH/DEL to erase
the last digit entered.
DM1000
17 Copyright © 2010 Waxess USA
2
DM1000 CB GSM.book Page 18 Sunday, July 11, 2010 10:28 PM
5 Press OK to set the code.
A beep confirms the setting and the Setup
menu appears.
2
6 Press Exit or OFF to return to the Standby
screen.
Add/remove a 1
With area codes stored in memory, the
and
keys have a unique function in phone memory
dialing.
If you need to add a 1 to a 10–digit phone number
for proper dialing in your area, press
. Press
again to remove the number 1. When retrieving a
number from the Caller ID log, use the
key to
add or remove a 1. This feature is not available
when using Redial.
Add/remove area code
If you need to add the area code to a 7–digit
number, press
to display the area code list. Scroll
to the correct area code, and press OK. At this point
you can also press
to add the number 1, if
needed.
To remove the area code, press
to remove the
number 1 (if present), then press
.
DM1000
18 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 19 Sunday, July 11, 2010 10:28 PM
Get set
Note: When dialing numbers from the Caller ID
log, area codes stored in the phone are not
accessible. Press
and use the keypad to
add the area code. This feature is not
available when using Redial.
•Language
09:00A 01/01
English
1 Press MENU, scroll to Setup,
and press Select.
French
Spanish
Portuguese
SELECT
EXIT
2 Scroll to Language, and press
Select.
The highlight bar shows the current language
setting.
3 Scroll to the language you want, and press
Select.
A beep confirms the setting and the Setup
menu appears. The menu appears in the
language you selected.
•LCD contrast
1 Press MENU, scroll to Setup, and press Select.
2 Scroll to LCD Contrast, and press Select.
3 Press to darken the display or
display.
to lighten the
4 Press OK to set the contrast.
DM1000
19 Copyright © 2010 Waxess USA
2
DM1000 CB GSM.book Page 20 Sunday, July 11, 2010 10:28 PM
•Name
2
Your phone arrives with the name “Base”
preassigned to the base. Each handset receives a
number (1–4) in the order of registration. You can
assign a unique name to the base and even change
the number and name assigned to a handset.
1 Press MENU, scroll to Setup, and press Select.
2 Scroll to Name the Unit and press Select.
3 Enter the name and press Select. See “Enter
names and characters” on page 31.
A tone confirms the setting.
•Handset registration
Register
You can register up to three more handsets with the
base. Each new cordless handset must be electronically
registered with the base. The cordless handset
included in this package is preregistered at the factory
with the base. If it somehow becomes deregistered,
use this procedure to reregister the handset.
1 On the handset, press MENU, scroll to Setup
and press Select.
2 Scroll to Register and press Select.
The display shows “Press and hold Intercom
on base, then OK.”
3 Press and hold Intercom (at least two seconds)
on the base until you hear a beep.
DM1000
20 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 21 Sunday, July 11, 2010 10:28 PM
Get set
4 Then, press OK on the handset.
Registration takes only a few seconds.
When registration completes,
you hear a tone and this
message appears on the LCD
screen.
Deregister
1 Press
MENU, scroll to Setup, and press Select.
2 Scroll to Deregister and press Select.
A list of registered cordless handsets appears.
3 Scroll to the handset you want to deregister and
press Select.
The confirmation message “Delete
registration?” appears.
4 Press Yes to confirm, or press No to return to
the previous screen.
When deregistration is complete, the
confirmation message “Handset 1 is
deregistered” appears.
DM1000
21 Copyright © 2010 Waxess USA
2
DM1000 CB GSM.book Page 22 Sunday, July 11, 2010 10:28 PM
3 GO!
•Make a wireless call
Cordless
handset
3
•Press
•Enter
•Press
OR
•Enter
•Press
Speakerphone Corded handset
on base
on base
•Enter number
number •Press CEL
CEL
CEL
number
•Lift handset off
base
•Enter number
•Press CEL
CEL
•To end the
•To end the
call, Press OFF call, press SPPHONE or OFF
•To end the call,
replace the
handset
Note: When making a wireless call, no dial tone is
generated until the phone connects to the
cellular network.
DM1000
22 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 23 Sunday, July 11, 2010 10:28 PM
GO!
•Make a landline call
Cordless
handset
•Press
•Enter
OR
•Enter
•Press
Speakerphone Corded handset
on base
on base
•Enter number
number •Press TEL
TEL
number
TEL
•To end the
•To end the
call, Press OFF call, press SPPHONE or OFF
•Lift handset off
base
•Enter number
•Press TEL
•To end the call,
replace the
handset
Set earpiece
volume
ON CORDED HANDSET
During a call, move the
selector switch to L, M, or
H.
ON BASE SPEAKER
PHONE
During a call, press
for
for softer.
louder or
DM1000
23 Copyright © 2010 Waxess USA
3
DM1000 CB GSM.book Page 24 Sunday, July 11, 2010 10:28 PM
ON CORDLESS HANDSET
DURING A CALL
Press
softer.
for louder or
for
•Calling options
3
Speed dial
1 Set up keys 0–9 with numbers in the phone
book for speed dial. See “Enter numbers
directly” on page 32.
2 Press and hold the appropriate number key,
then press CEL or TEL.
If you need to add or remove the number 1 or the
area code for proper dialing in your area, see “Add/
remove a 1” on page 18, or “Add/remove area
code” on page 18.
Redial
The phone memory holds the last five numbers
dialed. Each number can have up to 32 digits.
1 Press REDIAL/P to search through the numbers.
In the upper left corner, the LCD shows a C if
the call was on the cellular line or a T if the call
was on the landline.
2 Press CEL or TEL to redial the number.
DM1000
24 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 25 Sunday, July 11, 2010 10:28 PM
GO!
Pause (for TEL line use only)
While entering a phone number, press REDIAL/P to
add a two second pause. The pause is added as the
digits are transmitted when dialing. Press REDIAL/P
again to make the pause longer. The letter P
appears in the number each time you enter the
pause.
Note:
• Pause is available only when using the TEL line.
Pause may not be recognized as a valid number on
the cellular network and calls may not connect.
• Pause is disabled when dialing on the TEL line as
a second line, such as while the cellular line is
connected to another call. Pause is also disabled
during conference calls.
•Answer a wireless call
When the phone receives a wireless call:
• The base and all registered cordless handsets
ring.
• The CEL indicator flashes on the LCD
• The caller ID, if available, appears on the LCD
screen.
DM1000
25 Copyright © 2010 Waxess USA
3
DM1000 CB GSM.book Page 26 Sunday, July 11, 2010 10:28 PM
Cordless
handset
•Press CEL
3
Speakerphone
on base
Corded handset
on base
•Press CEL
•Lift handset off
base
OR
•Press SP-PHONE
•To end the call, •To end the call,
•To end the
call, press OFF press SP-PHONE replace the
handset
twice
or OFF
•Answer a landline call
When the phone receives a landline call
• The base and all registered cordless handsets ring.
• Caller ID, if available, appears on the LCD screen.
Cordless
handset
•Press TEL
Speakerphone
on base
Corded handset
on base
•Press TEL
•Lift handset off
base
OR
•Press SP-PHONE
•To end the
•To end the call, •To end the call,
call, press OFF press SP-PHONE replace the
or OFF
handset
twice
DM1000
26 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 27 Sunday, July 11, 2010 10:28 PM
GO!
•In-Call operations
Place a call on Hold
• Press Hold to place a call on hold.
• Press Exit to return to the call.
Mute a call
• Press Mute to temporarily cut off the microphone.
• Press Unmute to return to the call
Transfer a call
You can transfer calls between the base and the
handsets, and from handset to handset. This
function works for both cellular and landline calls.
BASE TO HANDSET TRANSFER
1 Press Intercom, scroll to the
handset (or base) that you
want and press Page.
The base and the handset
involved in the transfer
operation begin beeping (a
different tone than with the
Intercom function), and a
message appears on the LCD.
If there is no answer within 60 seconds, the
DM1000
27 Copyright © 2010 Waxess USA
3
DM1000 CB GSM.book Page 28 Sunday, July 11, 2010 10:28 PM
page and the transfer are cancelled and you
return to the call. You can press Exit to return
to the call immediately.
3
2 Press Answer to take the
transfer, or press Exit to
reject the transfer.
The call returns to the device
that started the transfer handset or base.
Note: When transferring between base and a
handset, the caller is transferred
immediately and is not put on hold.
3 Press OFF to end the call.
OR
Follow the steps above to transfer the call back
to the base.
You can also use the HOLD function to start a
transfer. During a call, press HOLD, select
Transfer, then follow the steps above.
HANDSET TO HANDSET
TRANSFER
1 During a call, press Intercom,
scroll to the handset you
want, and press Page.
The handset involved in the
transfer operation begins
beeping (a different tone
than with the Intercom
DM1000
28 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 29 Sunday, July 11, 2010 10:28 PM
GO!
function) and a message appears on the LCD.
If there is no answer within 60 seconds, the
page and the transfer are cancelled and you
return to the call. You can press Exit to return
to the call immediately.
2 Press Answer on the handset
receiving the page.
The call is now on hold, and
the parties with the handsets
can speak.
3 Press Exit on the handset that started the
transfer.
The call is now transferred to the receiving
handset.
On the receiving handset, you can press OFF or
Exit to reject the transfer. Then, the call returns
to the handset that started the transfer.
4 Press OFF to end the call.
You can also use the HOLD function to start a
transfer. During a call, press HOLD, select
Transfer, then follow the steps above.
DM1000
29 Copyright © 2010 Waxess USA
3
DM1000 CB GSM.book Page 30 Sunday, July 11, 2010 10:28 PM
Set up a conference call
3
Conference calling lets you make a call with two
other participants. The phone places the third call
with the service (cellular or landline) that is not
being used. The Conference feature is available only
with the cordless handset.
1 Make a normal call to the first participant.
2 Press Hold, scroll to Initiate a call, and press
Select.
3 Enter the number of the next participant, and
press CEL (or TEL).
When the other participant answers, you can
speak privately without the other participant.
Press FLIP to change between the participants.
The LCD shows which line (CEL or TEL) is in
use.
4 Press CONF to connect all participants.
5 To drop a participant from the conference call
press CEL DROP or TEL DROP.
Press OFF to drop all participants and end the
call.
DM1000
30 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 31 Sunday, July 11, 2010 10:28 PM
GO!
•Phone book
The phone book stores up to 50 names and numbers.
Enter names and characters
Use the keypad to choose the characters you want.
Each time you press a key, the letters on that key
appear first as capital letters, then as lower case
letters, then the number corresponding to that key.
Number of times key pressed
keys
DM1000
1
2
3
4
5
6
7
8
9
1
!
“
*
#
$
%
&
‘
(
)
<
>
+
,
-
.
/
:
;
?
@
\
=
^
_
‘
A
B
C
a
b
c
2
D
E
F
d
e
f
3
G
H
I
g
h
i
4
J
K
L
j
k
l
5
M
N
O
m
n
o
6
P
Q
R
S
p
q
r
s
7
T
U
V
t
u
v
8
W
X
Y
Z
w
x
y
z
9
0
Space
31 Copyright © 2010 Waxess USA
3
DM1000 CB GSM.book Page 32 Sunday, July 11, 2010 10:28 PM
• Use
and
to scroll left or right.
• Press Clear to erase a character.
Enter numbers directly
1 Press
MENU, scroll to Memory, and press
Select.
3
2 Scroll to Phone book, and press Select.
3 Scroll to Add new entry, and press Select.
“Name?” appears in the display.
4 Use the letters on the keypad to enter the name
(up to 16 characters) and press OK.
Press OK to leave Name blank.
“Number?” appears in the display.
5 Use the keypad to enter the number with area
code and press OK.
The Distinctive ring setting appears.
This feature lets you add a special ring tone to
phone numbers that you store in memory.
During an incoming call, the phone compares
the number to the distinctive ring list, and when
it finds a match, the distinctive ring plays.
Then, you can recognize a caller just from the
type of ring tone you hear.
6 Scroll to Ringer 1, 2, or 3, Melody 1, 2, or 3, or
No setting and press OK.
Melody tones are only available on the handset.
The Speed Dial screen appears.
DM1000
32 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 33 Sunday, July 11, 2010 10:28 PM
GO!
7 Choose an empty Speed Dial key number and
press OK.
A beep confirms the entry and the Standby
screen appears.
Press Skip to complete the entry without
registering it in Speed Dial.
Edit names or numbers
1 While in the phone book, scroll to Find name
and press Select.
2 Scroll to the name you want to edit and press
Select.
Call/Dial, Edit, Delete, and Delete all appear.
3 Use the
or
key to highlight Edit and press
Select.
4 Edit the name.
OR, Press OK to skip to the number.
5 Edit the number if needed and press OK.
You hear a tone, Complete appears in the LCD
and the list of names appears.
Enter numbers from Caller ID
1 While in the Caller ID log, scroll to the name/
number you want to enter in the phone book
and press Select.
Call/Dial, Save, Edit, and Delete appear.
2 Scroll to Save and press Select.“Name?”
appears.
DM1000
33 Copyright © 2010 Waxess USA
3
DM1000 CB GSM.book Page 34 Sunday, July 11, 2010 10:28 PM
3 If the Caller ID shows a name, press OK to
continue, or use the keypad to enter the name,
then press OK to continue.
3
4 If the Caller ID shows a number, press OK.
You can also use the keypad to enter a number,
then press OK.
The Distinctive ring settings appear.
5 Scroll to the ringer tone or melody you want,
and press OK.
The Speed dial setting appears.
6 Choose an empty Speed Dial key number, and
press OK.
A beep confirms the entry and the Standby
screen appears.
OR
7 Press Skip to complete the entry without
registering it in Speed Dial.
A tone confirms the entry and Complete
appears in the LCD. After a brief pause, the
name and number you just entered appears.
8 Press CEL or TEL to make the call.
Press OFF to return to Standby.
Use the
and
keys to enter a 1 or area
codes if needed for proper dialing in your area.
See “Add/remove a 1” on page 18. Or “Add/
remove area code” on page 18.
DM1000
34 Copyright © 2010 Waxess USA
D Mode CM1000CB GSM body.fm Page 35 Thursday, September 9, 2010 8:29 PM
GO!
Call from phone book
1 Press
MENU, scroll to Memory, and press
Select.
2 Scroll to Phone Book, and press Select.
3 Scroll to Find Name, and press Select.
4 Scroll to the name you want to dial and press
Select.
Four options appear on the LCD.
5 Scroll to Call/Dial and press Select.
The name and number appear in the LCD.
6 Press CEL or TEL to make the call.
Speed dial
For quick, one-button dialing, you can store up to
10 numbers in Speed Dial memory. See “Speed
dial” on page 24.
•Messages
Note: You must have a subscription to use these
message services described in this section.
Check with your service provider for
details.
DM1000
35 Copyright © 2010 Waxess USA
3
D Mode CM1000CB GSM body.fm Page 36 Thursday, September 9, 2010 8:29 PM
Voice messages
The DM1000 works with both cellular and landline
voicemail.
SET UP VOICEMAIL
1 Press MENU, and press Select on Messages.
3
2 Scroll to Voicemail setup, and press Select.
The cell number will be pre-programmed in
memory when the unit is activated.
3 Use the keypad to enter your voicemail number
(usually your cell number), then press OK.
The message VM number (TEL)? appears.
4 Use the keypad to enter the voicemail number
for your landline service, then press OK.
A beep confirms your entry.
In most cases the Cell Voicemail number and
your cell number are the same. If not, please
contact your service provider for the correct
number. Also, in a power outage this number
may require reprogramming if no backup
batteris are installed.
CHECK VOICEMAIL MESSAGES
When new messages are waiting, the message
LEDs on the base and the handset blink.
DM1000
36 Copyright © 2010 Waxess USA
D Mode CM1000CB GSM body.fm Page 37 Thursday, September 9, 2010 8:29 PM
GO!
The LED blinks faster for a landline voicemail,
slower for a cellular voicemail, and equally if there
are messages for both landline and cellular.
1 Press MENU, scroll to Messages, and press
Select.
2 Scroll to Voicemail and press Select.
3 Scroll to the voicemail–CEL Voicemail or TEL
Voicemail–with the message waiting and press
Select.
To manage messages (such as saving, deleting, or
forwarding), follow the commands for your specific
voicemail system.
Short Message Service (SMS)
This feature–available only with cellular service–lets
you send and receive text messages to other SMS
enabled cellular phones through the CEL connection
at the base or the cordless handset. Check with
your service provider for availability.
The options available in SMS are:
• Write new
• Saved
• In Box
• Storage status
Note: Due to the data access process in the
DM1000, the phone may not respond
instantly when keys are pressed. This is
normal operation, and any delay is no more
than one or two seconds.
DM1000
37 Copyright © 2010 Waxess USA
3
DM1000 CB GSM.book Page 38 Sunday, July 11, 2010 10:28 PM
WRITE A NEW MESSAGE
1 Press MENU, scroll to Messages, and press
Select.
2 Scroll to SMS, and press Select.
Write new is highlighted.
3
3 Press Select.
4 Use the keypad to write a message up to 160
characters long, including spaces and special
characters. See “Enter names and characters”
on page 31.)
5 When you finish writing, press OK.
The new message submenu appears with Send,
Edit, Save.
If the phone receives a call or someone initiates a
call on another handset while you are writing a
message, the message is automatically stored in
Saved messages. You can access the message later,
edit the message, if needed, then send the message
by following the steps below.
SEND A NEW MESSAGE
1 Write a message, then press OK.
Send, Edit, and Save appear.
2 Scroll to Send, and press Select.
Recipient No.? appears.
3 Enter the phone number of the recipient and
press OK.
DM1000
38 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 39 Sunday, July 11, 2010 10:28 PM
GO!
To send a message to a number that is stored
in the phone book, press MENU, scroll to the
entry you want, and press Select.
Note: Verify that the CEL line is not in use
before sending the message.
A confirmation message appears. Then, the
SMS menu appears. Press EXIT to return to the
SMS main menu.
4 To save the message before exiting, follow the
steps in “Save a new message.”
The message is stored in Saved messages for
easy viewing later.
OR
Press No to exit.
SAVE A NEW MESSAGE
1 After writing a message, press OK.
2 Scroll to Save, and press Select.
The message is stored in Saved messages for
easy viewing later. Press EXIT to return to the
SMS main menu.
VIEW SAVED MESSAGES
1 Press MENU, scroll to Messages, press Select.
2 Scroll to SMS, and press Select.
3 Scroll to Saved, and press Select.
4 Scroll to the message you want to read, and
press Select.
DM1000
39 Copyright © 2010 Waxess USA
3
DM1000 CB GSM.book Page 40 Sunday, July 11, 2010 10:28 PM
RECEIVE A MESSAGE
When the DM1000 receives a text
message, you hear a distinctive
ring tone and an envelope icon
appears in the display. The message goes to the
Inbox.
3
CHECK THE INBOX FOR READ AND UNREAD
(NEW) MESSAGES
1 Press MENU, scroll to Messages, and press
Select.
2 Scroll to SMS, and press Select.
3 Scroll to Inbox, and press Select.
4 Scroll to UnRead Messages, and press Select
The phone number from which the message
originated displays.
5 Press Select again to read the message.
If you have no unread messages, an error tone
sounds.
OR
6 Scroll to Read messages, and press Select.
The phone number from which the message
originated displays.
7 Scroll to the message you want to read, and
press Select.
DM1000
40 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 41 Sunday, July 11, 2010 10:28 PM
GO!
When you exit the Unread Messages list, any
messages that have not been viewed are
automatically stored in the Read Messages list. Be
sure to view all unread messages before exiting the
Unread Message list.
REPLY TO A MESSAGE
1 While reading a message, press Select.
2 Scroll to Reply, and press Select.
Write a reply the same way as you write a new
message, press OK, then Select to send the
message.
FORWARD A MESSAGE
1 While reading a message, press Select.
2 Scroll to Forward and press Select.
3 Enter the recipient’s number and press OK.
To send to a number from the phone book,
press MENU, scroll to the entry you want, and
press Select.
Note: Forwarding a message can only be done
through a CEL connection.
DELETE A MESSAGE
While reading a message, press Select, scroll to
Delete, and press OK.
DM1000
41 Copyright © 2010 Waxess USA
3
DM1000 CB GSM.book Page 42 Sunday, July 11, 2010 10:28 PM
CALL THE MESSAGE SENDER
While viewing a message, press Select, scroll to
Call, and press Select. The phone dials the number
automatically on the cellular service.
3
CHECK SMS STORAGE STATUS
1 Press MENU, scroll to Messages, and press
Select.
2 Scroll to SMS, and press Select.
3 Scroll to Storage Status and press Select.
The storage status appears.
The Storage status feature shows how many SMS
messages are saved in memory or stored in the
inbox. Storage capacity is limited, and there is no
indication that the memory is full. When the
message memory gets full, no more SMS messages
can be received, so it is important to clear the
memory frequently.
DM1000
42 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 43 Sunday, July 11, 2010 10:28 PM
More features
4 More features
•Caller ID
This feature helps identify incoming calls and
requires subscription through your service provider.
When Caller ID is active, your phone may display
the caller’s name and phone number if the landline
or cellular service supports it.
Note: Caller ID and Call Waiting are usually
included with cellular calling plans, but
landlines may require a separate
subscription. Check with your service
provider for details.
Caller ID information
SINGLE CEL OR TEL CALL
In Standby, the Caller ID normally
shows new and total calls received.
On a single incoming call, Caller
ID shows the time and date, the
caller’s name, and the number.
CEL or TEL blinks depending on
the type of
call–cellular service or landline.
DM1000
C 09:00A 01/01
Waxess
123-555-4567
Ring from CEL
CEL
TEL
43 Copyright © 2010 Waxess USA
4
DM1000 CB GSM.book Page 44 Sunday, July 11, 2010 10:28 PM
SIMULTANEOUS CEL AND TEL
CALL
C 09:00A 01/01
CEL: 123-555-4567
Waxess
TEL: 765-555-4321
Global Group
CEL
TEL
When both landline and cellular
services are active, the phone can
receive both types of calls at the same time or very
close together. When that happens, Caller ID
information for both calls appears in the display and
the call arriving first is on top.
CALL WAITING
4
If you receive another call during
a call in progress, information for
both calls appears in the displays
Press FLASH/DEL to answer the
new call. Press FLASH/DEL again to
return to the first call.
CT 09:00A 01/01
123-555-4567
Talk (TEL)
2:25
MUTE
HOLD
Call in progress
T 10:00A 01/05
Waxess
123-555-4567
CALL WAITING
2:25
Talk (TEL)
HOLD
MUTE
New call
If the current call is on the CEL
line and another call arrives also
on the CEL line, a “C” blinks in the display.
If the current call is on a CEL line and the new call
is on the TEL line, the “C” remains solid, and the “T”
indicator blinks.
If you receive a call waiting signal during the
conference call, press FLASH to answer the call.
DM1000
44 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 45 Sunday, July 11, 2010 10:28 PM
More features
Check the log
The Caller ID log lists the name associated with the
Caller ID data. If the data received does not have
proper name data, the phone number is listed
instead.
to scroll through the log from newest to
Press
oldest. Press
to scroll through the log from oldest
to newest. The log holds up to 50 entries.
4
Dial a number
1 Scroll to a name/number displayed, and press
Select twice.
The number appears in the display.
If the number’s area code is the same as an
area code stored in the phone memory (see
“Area codes” on page 17), the area code may
not appear. If the area code is required for
dialing, press # to add the area code to the
number. If the number 1 is also required for
dialing, press * to add 1 to the beginning of the
number.
2 Press CEL or TEL to make the call.
Save a number
1 Scroll to a name/number displayed, and press
Select.
DM1000
45 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 46 Sunday, July 11, 2010 10:28 PM
2 Scroll to Save, and press Select.
3 Enter a name if needed (see “Enter names and
characters” on page 31) and press OK.
4 Edit the number if needed and press OK.
The Distinctive Ring menu appears.
4
5 Scroll to the setting you want and press OK.
The Speed Dial menu appears.
6 Scroll to the speed dial number that you want
for this new entry and press OK.
OR
Press Skip to exit. A tone confirms that the
entry is stored in the phone book, and the name
and number appear in the display.
7 Press OFF twice to return to Standby.
Delete a number
ONE BY ONE
to scroll through the log from newest
1 Press
to scroll through the log from
to oldest. Press
oldest to newest.
2 Stop on the number you want, press Select.
3 Scroll to Delete, and press Select.
A confirmation message appears.
4 Press Yes to delete the number.
A tone confirms your choice and the Caller ID
log appears.
DM1000
46 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 47 Sunday, July 11, 2010 10:28 PM
More features
OR
Press NO and the Caller ID menu appears.
DELETE ALL
1 Press , then press Select.
2 Scroll to Delete ALL and press Select.
A confirmation message appears.
3 Press Yes to delete all data from the Caller ID
log.
OR
Press NO and the Caller ID menu appears.
•Call Forwarding
This feature lets you redirect an incoming call to
another telephone number.
Activate Call Forwarding
1 Press Menu, scroll to Set Up and press Select.
2 Scroll to Call Forwarding and
press Select.
3 Select Activate.
09:00A 01/01
LCD Contrast
CEL Number
Phone Set Up
Call Forwarding
SELECT
EXIT
09:00A 01/01
Activate
Deactivate
SELECT
DM1000
EXIT
47 Copyright © 2010 Waxess USA
4
DM1000 CB GSM.book Page 48 Sunday, July 11, 2010 10:28 PM
4 Enter the telephone number
to which you want to direct
the call and press OK, or press
Clear to erase the number.
Complete appears to confirm
your selection.
09:00A 01/01
Forward Number?
123-555-1234
OK
CLEAR
5 Forward FCN ON displays in the LCD.
NOTE: To avoid missing calls, follow the steps below
to deactivate Call Forwarding when no longer needed.
4
Deactivate Call Forwarding
1 Press Menu, scroll to Set Up and press Select.
2 Scroll to Call Forwarding and
press Select.
3 Select Deactivate.
Complete appears to confirm
your selection.
09:00A 01/01
LCD Contrast
CEL Number
Phone Set Up
Call Forwarding
SELECT
EXIT
09:00A 01/01
Activate
Deactivate
SELECT
EXIT
•Page and Intercom
Page
The Page feature lets you locate the handset if it is
misplaced, but it also can be answered by the
handset. Page can be initiated by the base or the
cordless handset.
DM1000
48 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 49 Sunday, July 11, 2010 10:28 PM
More features
1 Press INTERCOM on the base,
09:00A 01/01
2
scroll to the handset you want Handset
Handset 3
Handset
4
to page, and press PAGE.
ALL (Page Only)
PAGE
EXIT
OR
To send a page to all
registered handsets, select All and press PAGE.
The Page All feature is only available at the
base.
The handset beeps up to 60
seconds, and Paging Base
appears in the display.
2 On the handset receiving the
page, press ANSWER to
connect with the base.
On Intercom appears in the display.
3 Press Exit to stop the page without connecting
to the paging party through the Intercom.
For Page All, the page stops when any handset
responds to the page. Intercom is not available
for Page All.
Intercom
The Intercom feature is available on the handset
and the base.
1 Press INTERCOM, scroll to the handset you want
(or base), and press PAGE.
DM1000
49 Copyright © 2010 Waxess USA
4
DM1000 CB GSM.book Page 50 Sunday, July 11, 2010 10:28 PM
The handset or base beeps up to 60 seconds
and Paging Handset 1 (or 2, 3, or 4) appears
in the display.
2 To answer:
•
On the handset, press ANSWER to connect
with Intercom.
• On the base, lift the corded handset,
press ANSWER, or press SP-PHONE to
connect with the Intercom.
4
During an Intercom connection, use Mute to
turn off the microphone at the base or on the
handset.
Note: While using INTERCOM, an incoming call
from the CEL line automatically terminates
the INTERCOM connection. An incoming call
from the TEL line will not terminate the
INTERCOM connection unless the call is
answered by the base or any handset.
•Two-line calling
The Dual Mode Communication Terminal is a
two-line phone that offers unique calling features
because it can be used to make or receive two
separate calls at the same time; one call on the
landline (TEL) service and the other on the cellular
(CEL) service.
DM1000
50 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 51 Sunday, July 11, 2010 10:28 PM
More features
Quick reference chart
When
calling on:
Line
Second call can be
made:
Using
Line:
Base
Cellular
Any
cordless
handset
Landline
Cordless
handset
Cellular
Base
Landline
Cordless
handset
Cellular
Any
remaining
cordless
handset
Landline
Base
Landline
Any
remaining
cordless
handset
Cellular
Cordless
handset
Landline
Base
Cellular
Cordless
handset
Landline
Any
remaining
cordless
handset
Cellular
DM1000
51 Copyright © 2010 Waxess USA
4
DM1000 CB GSM.book Page 52 Sunday, July 11, 2010 10:28 PM
Make two separate calls
4
1 Use the base (corded handset or speakerphone)
to place a call–for example, a landline (TEL) call
(see “Make a landline call” on page 23).
2 Place a cellular (CEL) call, for example, with a
handset that is not in use (see “Make a wireless
call” on page 22).
• The display on any handset or
base not in use shows
XXX in use; XXX means base or
handset in this case.
• The two calls are completely
separate and cannot be conferenced.
• If Barge-In is on (see “Barge-in” on page 53), and
the first call is made from a cordless handset on a
landline, other handsets can join the call by
pressing TEL; but the base can not join the call.
Receive two separate calls
1 When a call comes in–for example, a landline
(TEL) call, answer it normally. In this example,
use the corded handset on the base. See
“Answer a landline call” on page 26.
2 If a cellular (CEL) call comes in, use a cordless
handset and press CEL to answer it.
DM1000
52 Copyright © 2010 Waxess USA
D Mode CM1000CB GSM body.fm Page 53 Friday, September 10, 2010 11:14 PM
More features
Remember that the corded handset and the
speakerphone on the base cannot be used at the
same time.
Call waiting with two calls
1 While a call is in progress (as in the above
example) and the landline (TEL) receives
another call, Call waiting appears in the display
and any other cordless handsets not in use will
ring.
2 To answer the call, press FLASH/DEL on the base,
or TEL on any handset not in use.
If the new call comes in on a different line,
press the appropriate key (CEL or TEL)
regardless of whether you are using the base or
a handset.
•Barge-in
After placing a TEL or CEL call with a cordless
handset, this feature allows up to three other
registered cordless handsets to join the call. Before
using the Barge-In feature, read the following
information.
• The D-Mode CT comes with the Barge-In feature
set to off–it must be activated before use.
• If power to the base is interrupted, Barge-In must
be reactivated.
DM1000
53 Copyright © 2010 Waxess USA
4
D Mode CM1000CB GSM body.fm Page 54 Friday, September 10, 2010 11:14 PM
• The first cordless handset to place the call is the
“master” and fully controls the call. Other
registered handsets that join the call are “slaves”
and can only join or exit the call.
• Barge-In works only for cordless handsets during
a call and is not operable on the base.
Note: Remember that with Barge-In activated,
privacy may be compromised. Any
registered handset can join the call, but
there is no indication that another handset
joined the call.
4
DM1000
54 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 55 Sunday, July 11, 2010 10:28 PM
More features
Quick reference chart
When
calling on:
Line
Second call can be
made:
Using:
Line:
Base1
Cellular
• 1 or more
cordless
handsets
Landline2,4
1 cordless
handset
Cellular
• Up to 3
cordless
handsets
• base
Landline2,3,4
2 or more
cordless
handsets
Cellular
Base
Landline • 1 cordless Cellular2,4
1 cordless
handset
Landline • 1 cordless Cellular2,4
2 or more
cordless
handsets
Landline • 1 cordless Cellular2,4
Not available
4
5
handset
handset
• base
handset
• base
Notes: See next page.
DM1000
55 Copyright © 2010 Waxess USA
D Mode CM1000CB GSM body.fm Page 56 Friday, September 10, 2010 11:17 PM
1 Base includes the speakerphone and corded
handset.
2 In Barge-In mode, Page/Intercom between
base and cordless is disabled during a call.
3 Conference call feature disabled for CEL and
TEL
4 Call transfer disabled
5 Use of two or more cordless handsets on cellular
line is only available in Cellular Only mode.
4
Set up Barge-In
1 Press MENU, scroll to Setup, and press Select.
2 Scroll to Barge-In and press Select.
3 Scroll to ON, and press OK.
A tone confirms the choice and the Setup menu
appears.
4 Press Exit twice to return to Standby.
Use Barge-In
1 Verify that Barge-In is activated, then use one
handset to place a call.
2 After the call is answered, press TEL or CEL
(depending on the service) on any handset to
join the call on the service selected.
DM1000
56 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 57 Sunday, July 11, 2010 10:28 PM
More features
•Cellular only
When activated on the base, the Cellular Only mode
enables up to four cordless handsets to join in a
conference call on the cellular line (CEL) call. Once
the landline is disconnected, activating Cellular
Only automatically deactivates the landline, so the
TEL icon on the LCD does not appear.
Set up Cellular only
1 You must disconnect the telephone cord
from the base.
2 Press MENU, scroll to Setup, and press Select.
3 Scroll to Cellular Only, and press Select.
4 Scroll to On, and press Select.
A tone confirms the choice, and the Setup menu
appears.
Note: With Cellular Only activated, privacy may
be compromised. Any registered cordless
handset can join the call, but there is no
indication that another handset has joined
the call.
Turn off Cellular only
If landline services are needed, deactivate this
feature first.
1 Press MENU, scroll to Setup, and press Select.
DM1000
57 Copyright © 2010 Waxess USA
4
DM1000 CB GSM.book Page 58 Sunday, July 11, 2010 10:28 PM
2 Scroll to Cellular Only, and press Select.
3 Scroll to Off, and press Select.
A tone confirms the choice, and the Setup
menu appears.
4 Connect the telephone cord and the TEL
indicator appears in the LCD.
•CEL Phone Number
4
Use this feature to see your CEL telephone number.
1 From the Stand-by mode, check the display to
ensure that the CEL mode is active.
CEL should appear in the lower left corner of the
display.
2 Press MENU, scroll to Setup, and press Select.
3 Scroll to CEL Phone Number and press Select.
The cellular number appears on the screen.
4 To exit, press Exit or Off.
•Power back-up
Power back-up for the base is an optional feature
(not required to operate this product) that allows
the base to operate for up 30 minutes (depending
on battery condition) even if AC power is disrupted.
If you install batteries for the Power Back-up
feature you can check the condition of the batteries
while they are installed.
DM1000
58 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 59 Sunday, July 11, 2010 10:28 PM
More features
1 On the base, press MENU, scroll to Setup, and
press Select.
2 Scroll to Battery Level, and press Select.
Current power level for the batteries appears.
If no batteries are installed, the level
indicates “Replace.”
OK
Replace
3 Press Exit to return to the Setup
menu.
Notes about Power Back-up
• Use new batteries.
• There are no indicators to inform you when the
phone is operating under regular power or backup
power.
• If you disconnect the AC power adaptor, Power
Back-up starts automatically.
• Check battery levels frequently, and replace the
batteries if the charge level drops below one half
of fully charged.
• After every power outage, check the batteries and
replace them as needed.
• Actual operating time using Power Back-up varies
depending on the condition of the batteries.
DM1000
59 Copyright © 2010 Waxess USA
4
DM1000 CB GSM.book Page 60 Sunday, July 11, 2010 10:28 PM
5 Precautions
Before you read anything else, please observe the
following precautions.
Warning!
Waxess USA, Inc. DOES NOT represent this unit to
be waterproof. To reduce the risk of fire, electrical
shock, or damage to the unit, DO NOT expose this
unit to rain or moisture.
5
Rechargeable Nickel-MetalHydride Battery Warning
• This equipment contains a rechargeable NickelMetal-Hydride battery.
• Nickel is a chemical known to state of California to
cause cancer.
• The rechargeable Nickel-Metal-Hydride battery
contained in this equipment may explode if
disposed of in a fire.
• Do not short-circuit the battery.
• Do not charge the rechargeable Nickel-MetalHydride battery used in his equipment in any
charger other than the one designed to charge this
battery as specified in the owner's manual. Using
another charger may damage the battery or cause
the battery to explode.
DM1000
60 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 61 Sunday, July 11, 2010 10:28 PM
Precautions
Rechargeable Nickel-MetalHydride Batteries Must Be
Recycled or Disposed of
Properly
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important and maintenance
(servicing) instructions in the literature
accompanying the appliance.
•Important safety instructions
When using your telephone equipment, these basic
safety precautions should always be followed to
reduce the risk of fire, electrical shock, and injury
to persons:
1 Read and understand all instructions.
2 Follow all warnings and instructions marked on
the product.
3 Unplug this product from the wall outlet before
cleaning. Use a dry cloth for cleaning without
liquid or aerosol cleaners.
4 Do not use this product near water; for
example, near a bathtub, wash bowl, kitchen
sink or laundry tub, in a wet basement, or near
a swimming pool.
5 Do not place this product on an unstable cart,
DM1000
61 Copyright © 2010 Waxess USA
5
DM1000 CB GSM.book Page 62 Sunday, July 11, 2010 10:28 PM
5
stand, or table. The telephone may fall, causing
serious damage to the unit.
6 Slots and openings in the cabinet and the back
or bottom are provided for ventilation. To
protect the product from overheating, these
openings must not be blocked or covered. This
product should never be placed near or over a
radiator or heat register. This product should
not be placed in a built-in installation unless
proper ventilation is provided.
7 This product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply to your home, consult your dealer or
local power company.
8 Do not allow anything to rest on the power cord.
Do not locate this product where the cord will be
damaged by persons walking on it.
9 Do not overload wall outlets and extension
cords, as this can result in the risk of fire or
electrical shock.
10Never push objects of any kind into this product
through cabinet slots, as they may touch
dangerous voltage points or short out parts that
could result in a risk of fire or electric shock.
Never spill liquid of any kind on the product.
11To reduce the risk of electric shock, do not
disassemble this product. Take it to qualified
service personnel when service or repair work is
required. Opening or removing covers may
DM1000
62 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 63 Sunday, July 11, 2010 10:28 PM
Precautions
expose you to dangerous voltages or other
risks. Incorrect reassembly can cause electric
shock when the appliance is subsequently used.
12Unplug this product from the wall outlet and
refer servicing to qualified service personnel
under the following conditions:
A When the power supply cord is damaged or
frayed.
B If liquid has been spilled into the product.
C If the product has been exposed to rain or
water.
D If the product does not operate normally
when following the operating instructions.
(Adjust only those controls that are covered
by the operating instructions. Improper
adjustment of other controls may result in
damage and will often require extensive
repair work by a qualified technician.)
E If the product has been dropped or the
cabinet has been damaged.
F If the product exhibits a distinct change in
performance.
13Do not use the telephone to report a gas leak in
the vicinity of the leak.
ADDITIONAL BATTERY SAFETY PRECAUTIONS
Caution: To reduce the risk of fire or injury to
persons by the battery, read and follow
these instructions:
1 Use only the battery pack specified in the
owner's manual.
2 Do not dispose of the battery pack in a fire. The
cell may explode. Check the Nickel Metal
DM1000
63 Copyright © 2010 Waxess USA
5
DM1000 CB GSM.book Page 64 Sunday, July 11, 2010 10:28 PM
3
4
5
5
6
Hydride battery disposal package insert for
disposal instructions.
Do not open or mutilate the battery pack.
Released electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if
swallowed.
Exercise care in handling the battery in order
not to short the battery with conducting
materials such as rings, bracelets, and keys.
The battery or conductor may overheat and
cause burns.
Charge the battery pack provided with or
identified for use with this product only in
accordance with the instructions and limitations
specified in the owners manual provided for this
product.
Observe proper polarity orientation between
the battery pack and battery charger.
SAVE THESE INSTRUCTIONS!
Important Electrical
Considerations
Unplug all electrical appliances when you know an
electrical storm is approaching. Lightning can pass
through your household wiring and damage any
device connected to it. This phone is no exception.
DM1000
64 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 65 Sunday, July 11, 2010 10:28 PM
Precautions
The FCC Wants You To Know
Changes or modifications to this product not
expressly approved by Waxess, or operation of this
product in any way other than as detailed by the
owner's manual, could void your authority to
operate this product. our telephone complies with
Part 68 of FCC Rules. You must, upon request,
provide the FCC registration number and the REN to
your telephone company. Both numbers are on the
base unit.
Note: You must not connect your phone to:
• coin-operated systems
• most electronic key telephone systems
This device complies with FCC rules for operating in
the GSM band. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) This device must
accept any interference received, including
interference that may cause undesired operation.
Privacy of communications, may not be ensured
when using this phone.
To insure the safety of users, the FCC has
established criteria for the amount of radio
frequency energy various products may produce
depending on their intended usage. This product
has been tested and found to comply with the FCC's
exposure criteria. For body worn operation, the FCC
DM1000
65 Copyright © 2010 Waxess USA
5
DM1000 CB GSM.book Page 66 Sunday, July 11, 2010 10:28 PM
RF exposure guidelines were also met when used
with the accessories supplied or designed for this
product. Use of other accessories may not ensure
compliance with FCC RF exposure guidelines and
should be avoided.
Range
5
Your new phone is designed to achieve the
maximum possible range by transmitting and
receiving according to the highest specifications set
forth by the FCC. We have rated this phone to
operate at a maximum distance with the
qualification that the range depends upon the
environment in which the telephone is used. Many
factors limit range, and it would be impossible to
include all the variables in our rating. The Maximum
Range rating of this phone is meant to be used as a
means of comparison against other range claims.
Telephone Line Problems
The FCC has granted the telephone company the
right to disconnect service in the event that your
phone causes problems on the telephone line. Also,
the telephone company may make changes in
facilities and services which may affect the
operation of your unit. However, your telephone
company must give adequate notice in writing prior
to such actions to allow you time for making
DM1000
66 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 67 Sunday, July 11, 2010 10:28 PM
Precautions
necessary arrangements to continue uninterrupted
service. If you are having trouble with your
telephone service, you must first disconnect your
phone to determine if it is the cause of your
problem. If you determine that it is the cause, you
must leave it disconnected until the trouble has
been corrected.
Radio Interference
Radio interference may occasionally cause buzzing
and humming in your cordless handset, or clicking
noises in the base. This interference is caused by
external sources such as TV, refrigerator, vacuum
cleaner, fluorescent lighting, or electrical storm.
Your unit is NOT DEFECTIVE. If these noises
continue and are too distracting, please check
around your home to see what appliances may be
causing the problem. In addition, we recommend
that the base not be plugged into a circuit that also
powers a major appliance because of the potential
for interference. Be certain that the antenna on the
unit is fully extended when needed. In the unlikely
event that you consistently hear other voices or
distracting transmissions on your phone, you may
be receiving radio signals from another cordless
telephone or other source of interference. If you
cannot eliminate this type of interference, you need
to change to a different channel. Finally, it should be
noted that some cordless telephones operate at
DM1000
67 Copyright © 2010 Waxess USA
5
DM1000 CB GSM.book Page 68 Sunday, July 11, 2010 10:28 PM
frequencies that may cause interference to nearby
TVs and VCRs. To minimize or prevent such
interference, the base of the cordless telephone
should not be placed near or on top of a TV or VCR.
If interference is experienced, moving the cordless
telephone farther away from the TV or VCR will
often reduce or eliminate the interference.
Cordless Telephone Privacy
5
Cordless telephones are radio devices.
Communications between the handset and base of
your cordless telephone are accomplished by
means of radio waves which are broadcast over the
open airways. Because of the inherent physical
properties of radio waves, your communications
can be received by radio receiving devices other
than your own cordless telephone unit.
Consequently, any communications using your
cordless telephone may not be private.
Installation Considerations
SELECTING A LOCATION
Before choosing a location for your new phone,
there are some important guidelines you should
consider:
• The location should be close to both a phone jack
and continuous power outlet. (A continuous power
DM1000
68 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 69 Sunday, July 11, 2010 10:28 PM
Precautions
outlet is an AC outlet which does not have a switch
to interrupt its power.)
• Keep the base and handset away from sources of
electrical noise such as motors or fluorescent
lighting.
• Be sure there is sufficient space to fully extend the
base antenna.
• The base can be placed on a desk or tabletop or
mounted on a standard telephone wall plate.
• You should charge your new phone for 12–15
hours before completing the installation or using
the handset.
Telephone Line Outlets
There are two types of phone outlets:
Modular Jack
Most phone equipment available now uses modular
jacks. Phone cords are fitted with a molded plastic
connector which plugs into this type of jack. If you
do not have modular phone jacks, contact your local
telephone company for information about their
installation.
Hardwired Jack
Some equipment is wired directly to a phone jack,
and these types of installations require a modular
jack converter. This type of installation is not
DM1000
69 Copyright © 2010 Waxess USA
5
DM1000 CB GSM.book Page 70 Sunday, July 11, 2010 10:28 PM
difficult; however, you should contact your
telephone dealer or a telephone supply store for
advice about the proper adapter or converter for
your particular situation.
Connecting the Telephone Cords
Consider these safety guidelines before connecting
the telephone cords:
Caution:
5
• Never install telephone wiring during a lightning
storm.
• Never touch uninsulated telephone wires or
terminals unless the telephone line has been
disconnected.
• Use caution when installing or modifying
telephone lines.
Applying Power to the base
This phone requires an AC outlet, without a switch
to interrupt power, and the included AC adapter. To
relieve strain on the DC plug when the phone is
placed on a desk or table, wrap the power cord
around the strain relief notch on the bottom of the
base.
DM1000
70 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 71 Sunday, July 11, 2010 10:28 PM
Precautions
Note: Place the power cord so that it does not
create a trip hazard, or where it could
become chafed and create a fire or other
electrical hazards.
•I.C. Notice
TERMINAL EQUIPMENT
Notice:This equipment meets the applicable
Industry Canada Terminal Equipment
Technical Specifications. This is confirmed
by the registration number. The
abbreviation, IC, before the registration
number signifies that registration was
performed based on a Declaration of
Conformity indicating that Industry
Canada technical specifications were met.
It does not imply that Industry Canada
approved the equipment.
Notice:The Ringer Equivalence Number (REN) for
this terminal equipment is marked on the
equipment itself. The REN assigned to
each terminal equipment provides an
indication of the maximum number of
terminals allowed to be connected to a
telephone interface. The termination on
an interface may consist of any
combination of devices subject only to the
requirement that the sum of the Ringer
Equivalence Numbers of all the devices
does not exceed five.
DM1000
71 Copyright © 2010 Waxess USA
5
DM1000 CB GSM.book Page 72 Sunday, July 11, 2010 10:28 PM
RADIO EQUIPMENT
The term "IC" before the radio certification number
only signifies that Industry Canada technical
specifications were met.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2)
this device must accept any interference, including
interference that may cause undesired operation of
the device. “Privacy of communications may not be
ensured when using this telephone.”
5
DM1000
72 Copyright © 2010 Waxess USA
D Mode CM1000CB GSM body.fm Page 73 Thursday, September 9, 2010 8:28 PM
General information
6 General information
This phone complies with FCC Parts 15 and 68.
AC Adaptor Information:
Base:
Input voltage 120V AC, 60Hz. 0.3A
Output voltage 9V DC, 1000 mA
Charger
Handset Charging Cradle
Input voltage 120V AC, 60 Hz, 0.15A
Output voltage 9V DC, 500 mA
Battery Information: Ni-MH, 3.6V, 1300mA
Frequency: GSM 850/1900 MHz
Handset/ Base 2.4GHz
Weight:
Handset 4.9 oz. (without battery)
7.3 oz. (with battery)
Base 1 lb., 13.7 oz. with corded handset
Dimensions:
Handset 6-3/4” x 2” x 1-1/4” (height, width,
depth)
Base 3-1/4” x 7-3/4” x 7-7/8” (height, width,
depth)
FCC ID Number SNBDM1000C/SNBDM100HS
Contains FCC ID: 09EQ26ELITE
Specifications, features, and availability of optional
accessories are all subject to change without prior notice.
Approved patents: 6,766,175/6,987,988/7,072,675/7,010,311/7,146,180
Patents pending: 11/234.297, 11/542.804, 11/593.725, 11/141.819
DM1000
73 Copyright © 2010 Waxess USA
6
DM1000 CB GSM.book Page 74 Sunday, July 11, 2010 10:28 PM
7 DM1000 Menu map
7
BASE
Messages
Voicemail
Voicemail Setup
SMS
Write New
Saved
In Box
Storage Status
Memory
Phone book
Find name
Add new entry
Caller ID
Ringer/Key Beep
Ringer tone
Ringer Volume
Night Volume
Key Beep
Setup
Distinctive Ring
Area Code
Language
Name the Unit
Tone/Pulse
Barge-In
Battery Level
Cellular Only
LCD Contrast
CEL Phone Number
Phone Set Up
Enter SPC
DM1000
Call Forwarding
Activate
Reactivate
Time and Date
CORDLESS HANDSET
Messages
Voicemail
Voicemail Setup
SMS
Write New
Saved
In Box
Storage Status
Memory
Phone book
Find name
Add new entry
Caller ID
Ringer/Key Beep
Ringer tone
Ringer Volume
Night Volume
Key Beep
Setup
Distinctive Ring
Area Code
Language
Name the Unit
Register
Deregister
LCD Contrast
TTY
74 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 77 Sunday, July 11, 2010 10:32 PM
Index
A
Activate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
B
barge-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
quick reference chart . . . . . . . . . . . . . . . . . . . 55
set up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
base unit batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
C
call
answer landline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
answer wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
conference call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
make landline call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
make wireless call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Call Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
caller ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
delete number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
dial number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
save number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
CEL phone number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
cellular only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
set up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
turn off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
cordless handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
battery indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
DM1000
77 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 78 Sunday, July 11, 2010 10:32 PM
charge the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
install batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
D
Deactivate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
distinctive ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32, 34
H
hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
I
included items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
L
location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
desk or tabletop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
wall mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
M
Menu Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
messages
SMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
check inbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
delete a message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
forward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
memory status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
reply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
save a new message . . . . . . . . . . . . . . . . . . . . . . . . . . 39
send . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
send a new message . . . . . . . . . . . . . . . . . . . . . . . . . . 38
write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
voice messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
check voicemail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
set up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
DM1000
78 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 79 Sunday, July 11, 2010 10:32 PM
mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
P
page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
phone book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
call from phonebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
enter characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
enter numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
phonebook
distinctive ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
edit names and numbers . . . . . . . . . . . . . . . . . . . . . . . 33
enter Caller ID numbers . . . . . . . . . . . . . . . . . . . . . . . . 33
enter speed dial number . . . . . . . . . . . . . . . . . . . . . . . 35
power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
R
redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
S
safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
set
area codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
dialing mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
earpiece volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
corded handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
cordless handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
speaker phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
handset registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
deregister . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
ringer tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
DM1000
79 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 80 Sunday, July 11, 2010 10:32 PM
night volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
time and date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
unit name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
signal level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
sim card
install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
speed dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
standby screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
T
text messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
two-line calling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
call waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
make calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
quick reference chart . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
receive calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
DM1000
80 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 81 Sunday, July 11, 2010 10:32 PM
Notes:
DM1000
81 Copyright © 2010 Waxess USA
DM1000 CB GSM.book Page 6 Sunday, July 11, 2010 10:33 PM
DM1000 User Guide
Copyright © 2010 Waxess USA, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising