Holmes 220 Snatcher [0501700] [04/2010]

Holmes 220 Snatcher [0501700] [04/2010]
OWNER'S MANUAL
220 SNATCHER
PARTS
NOTE: MANUAL including SPECIFICATIONS, subject to change without notice.
All ratings specified are based on structural factors only,
not vehicle capacities or capabilities.
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363
Phone (423) 238-4171 • FAX (423) 238-5371
FORM NO. 0501700
04 / 2010
PRICE $25.00
LIMITED WARRANTY
MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to the original
purchaser that each new MILLER wrecker or other MILLER products will be free from defects in material and
workmanship for a period of twelve (12) months from date placed in service, but in no event shall such warranty
period exceed twenty-four (24) months from date of manufacture by MILLER. The purchaser must promptly
notify MILLER in writing of any failure in material or workmanship. In no event shall MILLER accept such
notification later than twenty-four (24) months from date of delivery or twelve (12) months from date placed in
service, whichever is earlier.
MILLER's obligation under this warranty, statutory or otherwise, is limited to the repair or replacement at the
MILLER factory, or at a point designated by MILLER, of such part or parts as shall appear upon inspection
by MILLER to be defective in material or workmanship. New or remanufactured parts will be used for any
replacement at MILLER's option. This warranty is not transferable. This warranty does not obligate MILLER
to bear the cost of labor or transportation charges in connection with the repair or replacement of any parts
found to be defective, nor shall it apply to a product upon which repairs or alterations have been made unless
authorized by MILLER.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, MILLER MAKES NO OTHER WARRANTY,
EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. MILLER shall in no event be liable for claimed downtime, claimed loss of profits or goodwill, or
any other special, incidental, indirect, or consequential damages concerning or relating to any product or parts,
whether based on negligence, strict liability, breach of contract, breach of warranty, misrepresentation or any
other legal theory, regardless of whether the loss resulted from any general or particular requirement which
MILLER knew or had reason to know about at the time of sale.
MILLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS
MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY MILLER TO
PURCHASER, including, but not limited to, any vehicle to which a MILLER product may be affixed or any accessories
or wire rope, and MILLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE AS TO SUCH EQUIPMENT OR PRODUCTS. This language
shall in no way affect or diminish the rights of the purchaser to rely on such warranties as are extended by
such manufacturers or suppliers. MILLER shall, to the extent permitted under applicable law, pass on to the
purchaser such manufacturer's or seller's warranty.
MILLER, whose policy is one of continuous improvement, reserves the right to improve its products through
changes in design or materials as it may deem desirable without being obligated to incorporate such changes
in products previously sold. This warranty is not intended to cover or include the following items, which are set
forth by way of example and not limitation:
A.Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to weather,
road conditions, road treatments, etc.
B.Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs, failure to provide
reasonable and necessary maintenance, or uses for which the equipment was not designed or intended.
C.Alterations or modifications that affect performance, operation or reliability.
D.Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud flaps,
fenderettes, light bulbs, hydraulic oil, filters, and tow sling belts.
IT IS EXPRESSLY UNDERSTOOD THAT MILLER MAKES NO IMPLIED WARRANTY THAT MILLER
PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE OR FOR ANY OTHER
IMPROPER USE.
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363
Telephone (423) 238-4171
SERIAL NUMBER
OWNER, USER AND OPERATOR:
We appreciate your choice of our towing and recovery unit for your application. Our number one priority is
user safety which is best achieved by our joint efforts. We feel that you can make a major contribution to
safety if you, as the equipment owner and operator:
1.Comply with Federal, State, and Local Regulations.
2.Read, Understand, and Follow the Instructions in this Manual.
3.Use Good, Safe Work Practices in a Common Sense Way.
4.Only have Authorized and Trained Personnel performing maintenance on the Towing and Recovery
Unit.
© 2010 MILLER INDUSTRIES TOWING EQUIPMENT INC. All rights reserved. Reproduction or use, without express permission, of editorial or
pictorial content, in any manner, is prohibited.
i
TABLE OF CONTENTS
It is assumed by the manufacturer that the Owner/Operator has a thorough knowledge of the accepted and lawful
retrieval and towing methods as dictated by his city, county or state. The manufacturer rejects any liability claim that
may result from the incorrect or unlawful application of its equipment.
Section I - PARTS
SUBFRAME ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-2 & I-3
BOOM ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-4 & I-5
WHEEL LIFT ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-6 & I-7
CROSSBAR ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-8 & I-9
BOOM HYDRAULICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-10 & I-11
WHEEL LIFT HYDRAULICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-12 & I-13
CLAW HYDRAULICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-14 & I-15
ii
Section VI - PARTS
This Section is provided by the manufacturer for the purpose of ordering any component part of the Holmes 220
Snatcher that may be required when part replacement is necessary. Be certain to use only original equipment
replacement parts for warranty purposes as well as for keeping your unit in its original state and optimum operating
capacities.
When ordering replacement or spare parts be sure to provide the following information to the manufacturer's Parts
Department.
1.
2.
3.
4.
5.
6.
7.
Manual Number & Date of Publication
Manual Page Number
Page Title
Reference Number of Part Desired
Part Number
Part Description
Quantity of Part Desired
Providing this information will help ensure that the correct parts will be delivered to you in an expedient manner
without delay. Should additional information be required for repair or replacement of certain components, contact
your Wrecker Manufacturer Authorized Representative.
The Manufacturer reserves the right, without notice or obligation, to improve or modify their products, which may
change the specifications, models and feature availability.
I-1
Section I - PARTS (cont'd)
SUBFRAME ASSEMBLY
I-2
Section I - PARTS (cont'd)
SUBFRAME ASSEMBLY
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
PART NUMBER
0300113
0300134
0301895
0400070
0400126
0400367
0400392
0400451
0400452
0400480
0400482
0400487
0719519
0719520
9041353
25318004
25318008
25318010
25319009
805351000
810710000
HD0230
DESCRIPTION
GREASE FITTING, 1/4-28 STRAIGHT
HOSE CLAMP, 1" INSULATED
GREASE FITTING, 1/8 NPT STRAIGHT
1/4-20 X 1 HHCS GR5 ZP
3/8-16 X 1 HHCS GR.5,ZP
1/4-20 NYLOCK HEX NUT ZP
3/8-16 NYLOCK HEX NUT ZP
1/4 FLAT WASHER ZP
1/4 HELICAL LOCK WASHER ZP
3/8 FLAT WASHER ZP
3/8 HELICAL LOCK WASHER ZP
7/16 HELICAL LOCK WASHER ZP
SHIM - BOOM PIVOT ( .0747 THICK )
SHIM- BOOM PIVOT (.1196 THK)
7/16-20 UNF X 3/4 LG. HHCS
SUBFRAME WELD'T
HPU COVER WELDMENT
BOOM PIVOT PIN WELDMENT
HPU ASSEMBLY
PIN WELDMENT
LIFT CYLINDER
3/8-16 X 2 HHCS GR5 ZP
I-3
QTY
2
2
2
4
1
2
2
6
4
2
1
2
2
2
2
1
1
1
1
1
1
2
Section I - PARTS (cont'd)
BOOM ASSEMBLY
I-4
Section I - PARTS (cont'd)
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
BOOM ASSEMBLY
PART NUMBER
0301895
0303521
0306688
0400070
0400082
0400126
0400343
0400366
0400367
0400410
0400451
0400452
0400480
0400482
0400491
0400492
0708519
0718102
9041402
9053713
9056125
25317081
25318001
25318005
805351000
810730000
DESCRIPTION
GREASE FITTING, 1/8 NPT STRAIGHT
SPRING, HOSE TENSIONER
TIMBREN SPRING
1/4-20 X 1 HHCS GR5 ZP
1/4-20 X 1.125 EYE BOLT
3/8-16 X 1 HHCS GR.5,ZP
1/2-13 X 2 HHCS GR.8,ZP
1/4-20 HEX NUT ZP
1/4-20 NYLOCK HEX NUT ZP
NUT, 1/2"-13 HEX JAM ZP
1/4 FLAT WASHER ZP
1/4 HELICAL LOCK WASHER ZP
3/8 FLAT WASHER ZP
3/8 HELICAL LOCK WASHER ZP
1/2 HELICAL LOCK WASHER ZP
1/2 FLAT WASHER ZP
PLATE, ACCESS COVER BAR HOSE TENSIONER
1/2-13NC X 1 1/4 HHCS, ZP,GR.8
FLANGE BEARING, 1-1/2" I.D. OILITE
SNAP RING - 1-1/4" HEAVY DUTY
PIN, UPPER TILT CYLINDER
BOOM - PICKUP WHEEL SNATCHER
TILT STOP WELDT
PIN WELDMENT
CYLINDER HYDRAULIC FOLD
I-5
QTY
1
1
1
2
1
2
1
1
1
2
1
3
2
1
3
2
1
1
3
2
2
1
1
1
1
1
Section I - PARTS (cont'd)
WHEEL LIFT BOOM ASSEMBLY
I-6
Section I - PARTS (cont'd)
WHEEL LIFT BOOM ASSEMBLY
ITEM
PART NUMBER
3012-794003
3012-794004
0301397
0306819
0400066
0400121
0400126
0400133
0400139
0400154
0400204
0400343
0400349
0400367
0400392
0400398
0400410
0400416
0400482
0400497
0400505
0400606
0717674
0718216
0718217
9048166
25317020
25317105
25317200
25318002
25318003
25318011
25318013
810040004
810350001
896040002
0310639
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
DESCRIPTION
BAR - SPACER
PLATE - UL PAD CAGE
GREASE FITTING, 90 DEG
PAD, SLIDE
1/4-20 X 3/4 HHCS GR.5,ZP
3/8-16NC X 3/4 HHCS GR. B
3/8-16 X 1 HHCS GR.5,ZP
3/8-16 X 3 HHCS GR.5,ZP
SCREW, 3/8"-16 X 1-1/2" HEX SKT SET
3/8-16 X 1/2 HHCS GR.5,ZP
1/2-13X3/4 SKT HD SET
1/2-13 X 2 HHCS GR.8,ZP
SCREW, 3/8"-16 X 3/4" FL HD SKT
1/4-20 NYLOCK HEX NUT ZP
3/8-16 NYLOCK HEX NUT ZP
3/8-16 NYLOCK HALF-NUT ZP
NUT, 1/2"-13 HEX JAM ZP
1/2-13 NYLOCK HEX NUT GR.8, ZP
3/8 HELICAL LOCK WASHER ZP
1/2 FLAT WASHER GR.8,YZ PLATED
5/8 FLAT WASHER SAE
5/8 X 1-1/4 SHOULDER BOLT
SHIM - PAD SPACER
SHAFT- INNER TUBE CYLINDER
PLATE - XBAR POSITIONING
TUBE CLAMP, DOUBLE
PLATE - W/L FRONT COVER
PIN - EXTEND
BEARING - HOSE
OUTER W/L WELD'T
INNER STINGER BOOM WELD'T
PIN WELDMENT, TILT CYL LOWER
HOSE KEEPER
SHEAVE, SMALL GROOVED
PIN, STINGER PIVOT
NYLATRON PAD
CYLINDER 2.5 BORE X 1.13
I-7
QTY
1
1
2
2
2
4
1
1
1
1
2
4
1
2
2
1
2
4
4
8
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
4
1
Section I - PARTS (cont'd)
CROSSBAR ASSEMBLY
I-8
Section I - PARTS (cont'd)
CROSSBAR ASSEMBLY
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
PART NUMBER
0300113
0303844
0400349
0400428
0400546
0400590
0400667
0401006
0710092
0713885
0806978
0806979
0806980
0806981
0806982
E300002
HD0106
DESCRIPTION
GREASE FITTING, 1/4-28 STRAIGHT
CYLINDER, SWING L-ARM
SCREW, 3/8"-16 X 3/4" FL HD SKT
5/8-11 FLEXLOC THIN HIGH
COTTER PIN, 1/8" X 1-1/4"
CLEVIS PIN
3/8-16X1/2 FLT SOC HD THREAD LOCK
3/8"-16 X 1" FL HD SKT CAP SCREW
THRUST WASHER
PIN - CYLINDER (L-ARM END)
LEFT L ARM WLDT
RIGHT L-ARM WLDT
CROSSBAR WELDMENT
PIN PIVOT WLDT-XBAR
PIN L ARM PIVOT
BEARING - CLAW PIVOT
1/4 X 1-3/4 ROLL PIN ZP
I-9
QTY
3
2
2
2
2
2
2
2
2
2
1
1
1
1
2
2
2
Section I - PARTS (cont'd)
BOOM HYDRAULICS
I-10
Section I - PARTS (cont'd)
BOOM HYDRAULICS
ITEM
1
2
3
4
PART NUMBER
0301522
0310311
25319009
810710000
DESCRIPTION
CONNECTOR 6MJ-6MB
HOSE ASSY - 72" LG
HPU ASSEMBLY
LIFT CYLINDER
I-11
QTY
9
2
1
1
Section I - PARTS (cont'd)
WHEEL LIFT HYDRAULICS
I-12
Section I - PARTS (cont'd)
WHEEL LIFT HYDRAULICS
ITEM
1
2
3
4
5
6
7
8
PART NUMBER
0301522
0301921
0302922
0307042
0307460
25319009
810730000
0310639
DESCRIPTION
CONNECTOR 6MJ-6MB
HOSE ASSEMBLY, 128" LG
HOSE ASSEMBLY, 170" LG
CONNECTOR, (6MJ-6MBR-3/64)
FITTING, ELBOW, 6MJ-6MB90L
HPU ASSEMBLY
CYLINDER HYDRAULIC FOLD
CYLINDER 2.5 BORE X 1.13
I-13
QTY
9
2
2
1
2
1
1
1
Section I - PARTS (cont'd)
CLAW HYDRAULICS
I-14
Section I - PARTS (cont'd)
CLAW HYDRAULICS
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PART NUMBER
0301522
0301696
0302531
0303844
0303860
0303861
0303862
0303886
0306817
0400487
0718102
25313002
25319009
HC1291
DESCRIPTION
CONNECTOR 6MJ-6MB
ELBOW, 6MJ-6FJX90
HOSE ASSY - 75" LG
CYLINDER, SWING L-ARM
HOSE ASSEMBLY, 10-3/4"
HOSE ASSEMBLY, 17"
HOSE ASSEMBLY - 112" LG
PLUG - 1/4 SAE O-RING
BULKHEAD UNION (4MJ-4BLKHD W/NUT)
7/16 HELICAL LOCK WASHER ZP
BAR HOSE TENSIONER
HOSE ASSEMBLY - 110" LG
HPU ASSEMBLY
CONNECTOR, 4MJ-4MB STR
I-15
QTY
7
2
2
2
1
1
1
2
2
2
1
1
1
6
NOTES
NOTES
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive • Ooltewah, Tennessee 37363 • (423) 238-4171
www.millerind.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement