H970LCA

H970LCA
INSTALLATION GUIDE
CURRENT MONITORING
TM
H970LCA
TM
970LCA
Split-Core Low Current 4-20mA & 0-5VDC
DC Current Transducer
Installer’s Specifications
Technology
Amperage Range
Sensor Supply Voltage Supply Current Isolation
Temperature Range
Humidity Range
Output
Accuracy
Open loop Hall effect
0 to 20/40/80 ADC (slide switch selectable)
15-30VAC/DC for 4-20mA output;
12-30VAC/DC for 0-5VDC output
35mA max.
600VAC rms
-15° to 60°C (5° to 140°F)
10-90% RH non-condensing
4-20mA and/or 0-5VDC
±3% F.S. combined linearity, hysteresis, and repeatability
The product design provides for basic insulation only.
DANGER
quick install
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
•
•
•
•
•
Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes.
This equipment must only be installed and serviced by qualified electrical personnel.
Read, understand and follow the instructions before installing this product.
Turn off all power supplying equipment before working on or inside the equipment.
Use a properly rated voltage sensing device to confirm power is off.
DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION
• Only install this product on insulated conductors.
Failure to follow these instructions will result in death or serious injury.
1. Disconnect and lock out power to the conductor to be monitored.
2. Choose a location for the sensor. The monitored conductor must pass through the
iris, and the sensor must be at least 1/2” from any uninsulated conductors.
3. Install the adjustable mounting bracket to the back of the enclosure using the
included screws.
4. Connect supply voltage wires to the terminals marked Power (+) and Gnd (-).
5. Wire the output (mA or VDC) connections between the sensor and the controller.
NOTICE
•
•
•
•
6. Snap the sensor over the conductor to be monitored and clip the assembly to the
mounting bracket.
This product is not intended for life or safety applications.
Do not install this product in hazardous or classified locations.
The installer is responsible for conformance to all applicable codes.
Mount this product inside a suitable fire and electrical enclosure.
Wiring Example
7. Set the field-selectable switch to the desired amperage level (see page 2).
Dimensions
Removable Mounting Bracket
1.0”
(25 mm)
CONTACTOR
1.1”
(26 mm)
CONTROLLER
Bracket can be mounted
on either side for added
installation flexibility.
0.8”
(21 mm)
3.1”
(79 mm)
Analog
Input
4-20mA DC
Self-gripping
Iris
2.8”
(70 mm)
1.4”
(36 mm)
Ø = 0.3”
(8 mm)
2.5”
(64 mm)
MOTOR
Z203252-0E
PAGE 1
Fan or Pump
3.0”
(76 mm)
©2010 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected]
Use DIN Rail
Mounting clip
(Veris part
number AH01) to
mount on standard DIN rail.
10101
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
INSTALLATION GUIDE
H970LCA
TM
Operation
set-up and wiring
The H970LCA is a current-sensitive device that monitors DC current (amperage)
in the conductor passing through it. The unit combines a Hall Effect sensor with
proven transducer circuitry, with a status output suitable for connection to building
controllers or other appropriate data acquisition equipment operating at up to
30 volts. The H970LCA requires supply voltage to generate its output. Selectable
amperage ranges and output types maximize the installation flexibility.
To
Load
Amp Ranges
0-20
0-40
0-80
Controller must be programmed to account for
the extra turns. e.g., if four turns pass through
the sensor (as shown) the normal controller
reading must be divided by 4.
Gnd
Power
15-24 VAC/DC
Blink=Normal
Off=No Power
Solid=Overrange
0-20
0-40
0-80
Amperage Range
Selector Switch
Notes
For load currents less than sensor minimum rating:
0-5
VDC
Slide Switch
Amp Ranges
The H970LCA housing offers unprecedented mounting flexibility. The mounting
bracket can be attached in three different places. Additionally, the bracket is
compatible with the Veris AH01 DIN Rail clip, allowing DIN mounting.
Wrap the monitored conductor through the center hole and around the sensor body
to produce multiple turns through the “window.” This increases the current measured
by the transducer.
< 3.5 A (Sensor Min.)
4x
To
Load
4-20
mA
Wiring Diagram
Digital Control
1A
(+) Power
(-) GND
0-5 VDC
4-20mA
AI
To
Load
CAUTION
Amp Ranges
0-20
0-40
0-80
To
Load
4-20
mA
0-5
VDC
Gnd
Power
15-24 VAC/DC
Blink=Normal
Off=No Power
Solid=Overrange
RISK OF EQUIPMENT DAMAGE
• Derate the product’s maximum current for the number of turns
through the sensing window using the following formula.
• Failure to follow these instructions can result in overheating
and permanent equipment damage.
Failure to observe the following can result in distorted product calibration:
1. Observe the arrow on the product showing orientation to current source.
2. Do not expose the product to current levels greater than the maximum amperage
range.
scaling
20mA/5VDC
SENSOR OUTPUT
Rated Max. Amps ÷ Number of Turns = Max. monitored Amps
e.g. : 100A ÷ 4 Turns = 25 Amps max. in monitored conductor
4mA/0VDC
0A
SENSED AMPS
*Slide-Switch Selectable
20/40/80A*
troubleshooting
Problem
Z203252-0E
PAGE 2
Solution
The LED is off and no signal is
produced
Verify that power is applied to PWR (+) and GND (-)
terminals
The LED is on solid and the output
is at maximum
Verify that the amperage range selection switch is
in the proper position for the current applied to the
conductor.
©2010 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected]
10101
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement