Excel SIP Trunk Setup Guide
DSX
Excel SIP Trunk Setup
April 22, 2011
Issue 1.04
NEC Corporation of America
4 Forest Parkway, Shelton, CT 06484
Excel SIP Trunk Setup
DSX
1.04
Copyright 2011
NEC Corporation of America
6535 N. State Highway 161
Irving, TX 75039-2402
Communications Technology Group
Revision History
Issue
Date
1.03
1/19/11
1.04
4/22/11
NEC Corporation of America
Revisions
•
Corrected typo: Available SIP line numbers in a DSX-40 without
a COIU expansion card are 5-12.
•
In the System Administrator, Single registration mode is called
Common.
•
Updated required software level, expanded RTP port forwarding
range, and added System Administrator screen shots.
•
Removed requirement for 1104-09.
Page 2 of 2
April 22, 2011
DSX
Excel SIP Trunk Setup
1.04
Contents
1 Overview................................................................................................................................................ 4 2 Excel Setup............................................................................................................................................ 4 3 System Router Setup............................................................................................................................. 4 3.1 NAT and SIP....................................................................................................................................... 4 3.2 Port Forwarding and Codecs .............................................................................................................. 4 4 DSX Setup ............................................................................................................................................. 4 4.1 Software Level .................................................................................................................................... 4 4.2 Assign SIP Lines................................................................................................................................. 5 4.3 Select the SIP Trunk Provider Type ................................................................................................... 6 4.4 Set Up the SIP Trunk Registration...................................................................................................... 6 4.5 Codec Setup ....................................................................................................................................... 7 4.6 Assign DID Numbers to your SIP Lines.............................................................................................. 7 4.7 Fax Setup ........................................................................................................................................... 7 Tables
Table 1: Excel Account Information ............................................................................................................. 4 NEC Corporation of America
Page 3 of 3
April 22, 2011
DSX
1
Excel SIP Trunk Setup
1.04
Overview
The DSX is compatible with Excel SIP LD Trunking. This setup guide summarizes the account
information you will receive from Excel and provides step-by-step instructions on how to program that
information into the DSX.
You can set up SIP trunks as standard loop start lines or DID lines. All the feature available with other
types of loop start and DID lines are also available with Excel SIP trunk lines. For details on the features
available with loop start and DID lines, refer to the on-line DSX Software Manual at:
http://www.necdsx.com/docs/dita/dsx_v3_complete/index.html
Note: DSX does not currently support fax over sip lines.
2
Excel Setup
To set up your SIP LD Trunking account, contact Excel at http://www.excel.com. Once your account is set
up they will provide you with the following service information:
Table 1: Excel Account Information
Option
EXCEL IP
3
3.1
Description
The EXCEL IP is the IP address to which the DSX sip lines
will connect.
Fixed WAN IP Address
Excel SIP LD Trunking terminates to a fixed WAN IP address
at your site. Normally, this is the WAN IP address of the router
to which the DSX is connected.
DID(s)
These are the telephone numbers that users will dial to reach
you over your Excel LD SIP trunks.
System Router Setup
NAT and SIP
In the router to which the DSX is connected, enable NAT and disable all special SIP management
features (such as SIP ALG).
3.2
Port Forwarding and Codecs
Forward UDP ports 5060 and 1024 through 1215 to the DSX system’s IP address. Excel uses
Codecs G.711 and G.729 which are automatically supported in DSX. Note that the default frame
size (ptime) for G.711 set in 1812: Frame Size is 40mS. Excel recommends that you change this to
20mS.
4
4.1
DSX Setup
Software Level
3.31.96 or higher.
NEC Corporation of America
Page 4 of 4
April 22, 2011
DSX
4.2
Excel SIP Trunk Setup
1.04
Assign SIP Lines
1231-01: IP Lines [SYSTEM: PORTS: IP LINES: IP LINE ASSIGNMENT]
The first DSX SIP line is the first line beyond the last assigned line. Each SIP line uses an IP
resource (licensed VoIP port) in DSX. The maximum number of VoIP licenses is 8 in DSX-40 and
16 in DSX-80/160.
Example with DSX-40:
•
The first SIP line in a DSX-40 without a COIU expansion card is line 5. Available SIP line
numbers are 5-12.
•
With the COIU expansion card installed, the first SIP line is line 9. Available SIP line
numbers are 9-16.
•
DSX-40 supports a maximum of 8 VoIP licenses. When the total number of licenses are in
use, only Peer-to-Peer calls are available.
Example with DSX-80/160:
•
The first SIP line in a DSX-80/160 with a single 8COIU card is line 9. Available SIP lines
are 9-17.
•
The last line number in DSX-80/160 is 64. In a system with an 8COIU and two T1/PRI
cards, this will limit the available number of SIP lines.
•
DSX-80/160 supports a maximum of 16 VoIP licenses. When the total number of licenses
are in use, only Peer-to-Peer calls are available.
1232-01: IP Line Provider Number [SYSTEM: PORTS: IP LINES: IP LINE ASSIGNMENT]
Assign each SIP line in DSX to a provider number (1 or 2). DSX supports up to two providers
simultaneously.
Example: If Excel is your only SIP trunk provider, assign all the SIP lines designated in 1231-01 to
provider 1.
1232-02: IP Line Username [SYSTEM: PORTS: IP LINES: IP LINE ASSIGNMENT]
1232-03: IP Line Password [SYSTEM: PORTS: IP LINES: IP LINE ASSIGNMENT]
These options are not used with Excel SIP trunks.
NEC Corporation of America
Page 5 of 5
April 22, 2011
DSX
4.3
Excel SIP Trunk Setup
1.04
Select the SIP Trunk Provider Type
1831-01: Provider Number [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2)]
Select the provider number you want to set up. This selection corresponds to the provider number
you assigned to the SIP lines in 1232-01.
Example: If Excel is your only SIP trunk provider, and you have chosen provider 1 in 1232-01,
select provider 1 for this option also.
1831-02: Provider Type [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): SERVICE PROVIDER]
Dial 05 to choose Excel as the type for the provider selected in 1831-01.
1831-03: Provider Name [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): DESCRIPTION]
The provider name is an optional 18-character entry that describes the provider. Enter any name
you like – the entry does not affect provider setup or registration.
1831-04: Profile [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): PROFILE]
Select the VoIP profile that the system will use when connecting to the SIP trunk provider. The
entry you make here corresponds to the profiles set up in programs 1811-1815. Choose profile 4.
4.4
Set Up the SIP Trunk Registration
1832-01: Provider IP Registration [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): SERVER ADDRESS]
Select the provider number you want to set up (see 1831-01) and enter the Table 1 EXCEL IP
entry as it was provided to you by Excel. This option uses the text entry method.
1832-02: Registration Type [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): REGISTRATION TYPE]
Choose the IP line registration type. DSX IP lines can share the same registration (01: Single),
have a unique registration for each line (02: Per Line), or require no SIP registration (00: None) .
For Excel, choose 00: None. Excel SIP LD is a peer-to-peer service that requires no SIP
registration.
1832-03: Account Username [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): USER]
1832-04: Account Password [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): PASSWORD]
1832-05: Proxy [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): PROXY ADDRESS]
1832-06: SIP Type or Service (ToS) [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): SIP TOS]
1832-07: RTP Type of Service (ToS) [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): RTP TOS]
These options are not used with Excel SIP trunks.
NEC Corporation of America
Page 6 of 6
April 22, 2011
DSX
4.5
Excel SIP Trunk Setup
1.04
Codec Setup
1812: Codecs [SYSTEM: VOIP: PROFILE 4: CODECS]
For Excel SIP Trunks, leave Profile 4 at default.
4.6
Assign DID Numbers to your SIP Lines
3101-07: Telephone Number [LINES: CONFIG: SETUP: TYPE: PHONE NUMBER]
For each of your SIP lines, enter a telephone number that corresponds to one of the DID numbers
in Table 1. Each line must have a unique entry. This entry is required for both Loop Start and DID
lines.
4.7
Fax Setup
1812: Codecs [SYSTEM: VOIP: PROFILE X: CODECS]
1815: DTMF [SYSTEM: VOIP: PROFILE X: PAYLOAD TYPES]
SIP trunks to be used for fax must be set for G.711, 20mS Frame Size, with Inband DTMF. The fax
is transmitted in-band DTMF only.
NEC Corporation of America
Page 7 of 7
April 22, 2011
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement