AVSC-SDI-HDMI_A6_rev1

AVSC-SDI-HDMI_A6_rev1
AVSC-SDI-HDMI
SDI to HDMI Scaler and Converter
Converts 3G/HD/SD-SDI-and-audio-withlocal-loopout to HDMI digital video (DVI-D)
with analog stereo audio.
Customer
Support
Information
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S.
call 724-746-5500) • FREE technical support 24 hours a day, 7 days
a week: Call 724-746-5500 or fax 724-746-0746 • Mailing address:
Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: www.blackbox.com • E-mail: [email protected]
Trademarks Used in this Manual
Trademarks Used in this Manual
Black Box and the Double Diamond logo are registered trademarks of
BB Technologies, Inc.
HDMI is a registered trademark of HDMI Licensing LLC.
Any other trademarks mentioned in this manual are acknowledged to be
the property of the trademark owners.
Disclaimer
Black Box Network Services shall not be liable for damages of any kind,
including, but not limited to, punitive, consequential or cost of cover damages,
resulting from any errors in the product information or specifications set forth in
this document and Black Box Network Services may revise this document at any
time without notice.
Page 2
724-746-5500 | blackbox.com
FCC and IC RFI Statements/NOM Statement
FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY
CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio-frequency energy, and if
not installed and used properly, that is, in strict accordance with the
manufacturer’s instructions, may cause inter­ference to radio communication. It
has been tested and found to comply with the limits for a Class A computing
device in accordance with the specifications in Subpart B of Part 15 of FCC rules,
which are designed to provide reasonable protection against such interference
when the equipment is operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference, in which case the
user at his own expense will be required to take whatever measures may be
necessary to correct the interference.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emis­sion
from digital apparatus set out in the Radio Interference Regulation of Industry
Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant
les limites applicables aux appareils numériques de classe A prescrites dans le
Règlement sur le brouillage radioélectrique publié par Industrie Canada.
Normas Oficiales Mexicanas (NOM)
Electrical Safety Statement
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes
de que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para
referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de
operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
724-746-5500 | blackbox.com
Page 3
NOM Statement
5. El aparato eléctrico no deberá ser usado cerca del agua — por ejemplo,
cerca
de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc.
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales
que sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea
recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más
allá a lo descrito en las instrucciones de operación. Todo otro servicio
deberá ser referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no
interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,
alfombra o superficie similar puede bloquea la ventilación, no se debe
colocar en libreros o gabinetes que impidan el flujo de aire por los orificios
de ventilación.
10.El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor
como radiadores, registros de calor, estufas u otros aparatos (incluyendo
amplificadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo
del tipo descrito en el instructivo de operación, o como se indique en el
aparato.
12. Precaución debe ser tomada de tal manera que la tierra fisica y la
polarización del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no
sean pisados ni pellizcados por objetos colocados sobre o contra ellos,
poniendo particular atención a los contactos y receptáculos donde salen
del aparato.
14.El equipo eléctrico debe ser limpiado únicamente de acuerdo a las
recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las
lineas de energia.
16.El cable de corriente deberá ser desconectado del cuando el equipo no
sea usado por un largo periodo de tiempo.
Page 4
724-746-5500 | blackbox.com
NOM Statement/Safety Notice
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean
derramados sobre la cubierta u orificios de ventilación.
18.Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en su
desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
Safety Notice
Please read and follow the safety instructions to protect yourself from possible
injury and to minimize the risk of damage to the unit.
• Follow all instructions and warnings marked on the unit.
• Do not attempt to service the unit yourself, except where explained in this
manual.
• Provide proper ventilation and air circulation and do not use near water.
•K
eep objects that might damage the device away from it, and place the unit
on stable surfaces.
•O
nly use the power adapter, power cords, and connection cables designed for
the unit.
•D
o not use liquid or aerosol cleaners to clean this unit. Always unplug the
power to the device before cleaning.
724-746-5500 | blackbox.com
Page 5
Table of Contents
Table of Contents
1. Specifications..........................................................................................7
2. Overview.................................................................................................9
2.1Introduction...................................................................................9
2.2Features..........................................................................................9
2.3 What’s Included.............................................................................9
2.4 Hardware Description..................................................................10
3. Connection Diagram............................................................................12
4. OSD Menu............................................................................................13
5. Operation..............................................................................................15
6.Troubleshooting................................................................................... 22
6.1 Contacting Black Box.................................................................. 22
6.2 Shipping and Packaging............................................................. 22
Page 6
724-746-5500 | blackbox.com
Chapter 1: Specifications
1. Specifications
Approvals
CE, FCC
Audio Support
Stereo PCM (48 kHz only up to 8 channel)
CEC Channel
N/A
Enclosure
Metal wall mounting case with screws
ESD Protection
Human body model:
±19 kV (air-gap discharge) and
±12 kV (contact discharge);
Core chipset: ±2 kV
Firmware Update
via USB Port
Frequency Bandwidth
Output video: 165 MHz;
Input video: 2.970 Gbps, 2.970/1.001 Gbps
Input Video Support
3G: 1080p @50/59, 94/60 Hz (4:2:2);
HD: 720p @50/59, 94/60 Hz,
1080i @50/59, 94/60 Hz,
1080p @24/30 Hz;
SD: NTSC @59.94 Hz,
PAL @50 Hz
SDI Standards
SD-SDI, HD-SDI, and 3G-SDI
Connectors
Input:
SDI: (1) 3G 75-ohm interlocked BNC socket;
Output:
(1) HDMI Type A (19-pin female),
(1) BNC (SDI Loopout);
(1) USB mini for firmware update
Indicators
(1) Red LED for Power;
(1) Green LED for Video Signal
724-746-5500 | blackbox.com
Page 7
Chapter 1: Specifications
1. Specifications (continued)
Environment
Temperature Tolerance:
Operating: 32 to 104° F (0 to 40° C);
Storage: -4 to +140° F (-20 to +60° C)
Relative Humidity: 20–90%, noncondensing
Power
Power supply: 5 VDC, 2 A;
Consumption 5 Watts (max.)
Dimensions
1.1"H x 3.6"W x 3.3"D (2.8 x 9.2 x 8.3 cm)
Weight
9.1 oz. (260 g)
Page 8
724-746-5500 | blackbox.com
Chapter 2: Overview
2. Overview
2.1 Introduction
Scalers work to convert and scale a type of video/audio signal to another type
of video/audio signal. This enables you to use differently formatted video/audio
signals on differently formatted display screens. Scaling allows for changing
resolutions to increase quality or improve compatibility.
The SDI to HDMI Scaler and Converter (AVSC-SDI-HDMI) converts digital 3D/
HD/SD-SDI to HDMI digital video with analog stereo audio. With this module,
3G/HD/SD-SDI based devices such as Blu-ray disc players, PS3, DVD players,
camcorders, or set-top boxes can connect to your PC LCD and PC speakers. The
conversion between SDI and HDMI is pure digital and guarantees no loss transformation for both audio and video. Plus, with up to 8 channels audio support,
7.1 channel or 5.1 channel audio becomes available. The scaler also provides two
low-jitter and reclocked outputs for daisychain or multiple monitors.
2.2 Features
• IR remote control
• Remote control via Mini-USB
• OSD control interface
• Input bandwidth: 2.970 Gbps
• Maximum output pixel rate: 165 MHz
• Output video resolutions support multiple VESA standards
• Deinterlacer supported
• Supports noise reduction and video enhancement features
• Over/under scanning adjustable
• Video H/V mirror supported
• Active video area adjustment supported
• USB firmware upgradable for expanding compatibility
• Wallmount housing design for easy installation
2.3 What’s Included
• SDI to HDMI Scaler and Converter
• 5-VDC, 2-A power supply unit
• IR Remote control
• This User's Manual
• Installation software CD (CD included; software can also be downloaded from
blackbox.com)
724-746-5500 | blackbox.com
Page 9
Chapter 2: Overview
2.4 Hardware Description
Figures 2-1 and 2-2 show the front and back panels of the scaler. Table 2-1
describes its components.
1
2 3 4
5
5
5
Figure 2-1. Front panel.
6
7
8
9
10
Figure 2-2. Back panel.
Page 10
724-746-5500 | blackbox.com
Chapter 2: Overview
Table 2-1. Scaler components.
Number
Component
Description
1
SDI Local Loopout
3G/HD/SD-SDI local loopout
2
DIP switch
For firmware update:
ON (UP): firmware update mode;
OFF (DOWN): normal mode
3
(2) LED indicators
(1) Red LED for Power;
(1) Green LED for Video Signal
4
IR sensor
Used to receive the IR commands from IR
remote
5
(3) Push buttons
Left: Down button;
Middle: Up button;
Right: Menu/Enter button
6
Interlocking
power jack
Connects to 5 VDC power supply unit
7
Mini-USB port
• Used for firmware update
8
Stereo audio out
Connects to analog stereo audio speaker.
9
HDMI out
Connects to a HDMI display with a HDMI
male-male cable with locking nut
10
SDI IN
3G/HD/SD-SDI input
• Connects to 5 VDC power supply unit
724-746-5500 | blackbox.com
Page 11
Chapter 3: Connection Diagram
3. Connection Diagram
SDI cable
AVSC-SDI-HDMI
front (top) and
back (bottom)
Local monitor
with SDI input
Front
Rear
SDI cable
Stereo audio
cable
Camera with
SDI output
HDMI cable
Display with
HDMI input
Figure 3-1. Typical application.
Page 12
724-746-5500 | blackbox.com
Chapter 4: OSD Menu
4. OSD Menu
Table 4-1. OSD menu.
Option
Description
Settings
1. Output Setup
Output Mode
RGB;
YcbCr444;
YcbCr422
Default Pattern
Disable (Default);
White;
Cross;
Hatch;
Color;
Gray;
Windows;
H-Ramp;
W-HRamp;
W-VRamp;
Diagonal
Audio source
Stereo;
S/PDIF
Contrast
0–255 (Default = 0)
Brightness
0–255 (Default = 0)
Saturation
0–255 (Default = 0)
Hue
0–255 (Default = 0)
B/W Extension
Off (Default)
2. Image
On
Color Tone
Off (Default)
Skin
Green
724-746-5500 | blackbox.com
Page 13
Chapter 4: OSD Menu
Table 4-1 (continued). OSD menu.
Option
Description
Settings
2. Image
(continued)
Edge Enhance
Typ. (Default);
Mid;
Max;
Off
Sharpness
0–127
Under/Over Scan
-50%–50% (Default Off)
Aspect Ratio
16:9 (Default);
4:3
H-Mirror
Off (Default);
On
V-Mirror
Off (Default);
On
H-Shift
-100–100 (Default 0)
V-Shift
-50–50 (Default 0)
3. Adjustment
4. System
Input Res. Info
Firmware Version
Factory Reset
Page 14
No (Default);
Yes
724-746-5500 | blackbox.com
Chapter 5: Operation
5. Operation
Method A: Push-in Button
See Figure 5-1.
Down Up Menu
Figure 5-1. Location of push buttons on the scaler.
Method B: IR Remote Control
Figure 5-2. Remote control.
724-746-5500 | blackbox.com
Page 15
Chapter 5: Operation
Table 5-1. IR remote control functions.
Button
Function
FREEZE
Freeze video
ASPECT RATIO
Aspect ratio change
BLANK
Blank video
EXIT
Exit OSD
ENTER
Enter key
UP
Up key
LEFT
Left key
RIGHT
Right key
DOWN
Down key
MENU
Menu on
INPUT INFO
Source resolution information
1080p60
Select 1080p60 output resolution
1080i60
Select 1080i60 output resolution
720p60
Select 720p60 output resolution
480p60
Select 480p60 output resolution
Page 16
724-746-5500 | blackbox.com
Chapter 5: Operation
Method C: IR Remote Control through Mini-USB port
Figure 5-3.
724-746-5500 | blackbox.com
Page 17
Chapter 5: Operation
Table 5-2. IR remote control through mini-USB port screen functions.
Number in Figure 5-3
Function
1
COM Port Selection
2
COM Port Detection Button
3
Output Setup Button
4
Image Button
5
Adjustment Button
6
System Button
7
Input/Output Resolution Info
8
Refresh Input/Output Resolution Info Button
9
Output Quick Selection Button
1. COM Port Selection
Please select the COM PORT application.
Figure 5-4. Select COM port.
2. COM Port Detection Button
Click on the curved-arrow button
Page 18
to detect the COM PORT.
724-746-5500 | blackbox.com
Chapter 5: Operation
3. Output Setup Button
Figure 5-5.
4. Image Button
Figure 5-6.
724-746-5500 | blackbox.com
Page 19
Chapter 5: Operation
5. Adjustment Button
Figure 5-7.
6. System Button
Figure 5-8. System screen.
1) In-Sync Info:
To view the current input resolution
2) Factory Reset Button
3) Firmware Update Button
Page 20
724-746-5500 | blackbox.com
Chapter 5: Operation
Figure 5-9. Firmware update screen.
Follow these steps to update the firmware:
STEP A: Unplug the Mini-USB connector from the device.
STEP B: Set the DIP switch to ON (UP).
STEP C: Connect the device to the PC via a USB to mini-USB cable.
STEP D: Click the FW Update button in the software.
STEP E: Click on the “Load File” button to select the firmware file.
STEP F: Click on the “Burn” button to start the firmware update process.
STEP G: Unplug the Mini-USB connector from the device.
STEP H: Set the DIP switch to OFF (DOWN).
The firmware update process is complete.
7. I/O Port and Resolution Info
Displays the information about the I/O Port and the applied resolution.
8. Refresh Button
Refreshes the status of the converter.
9. Output Quick Selection Button
Controls common functions for quick setting.
724-746-5500 | blackbox.com
Page 21
Chapter 6: Troubleshooting
6. Troubleshooting
6.1 Contacting Black Box
If you determine that your SDI to HDMI Scaler and Converter is malfunctioning,
do not attempt to alter or repair the unit. It contains no user-serviceable parts.
Contact Black Box Technical Support at 724-746-5500 or [email protected]
Before you do, make a record of the history of the problem. We will be able to
provide more efficient and accurate assistance if you have a complete description, including:
• the nature and duration of the problem.
• when the problem occurs.
• the components involved in the problem.
• a ny particular application that, when used, appears to create the problem or
make it worse.
6.2 Shipping and Packaging
If you need to transport or ship your SDI to HDMI Scaler and Converter:
• Package it carefully. We recommend that you use the original container.
• If you are returning the unit, make sure you include everything you received
with it. Before you ship for return or repair, contact Black Box to get a Return
Authorization (RA) number.
Page 22
724-746-5500 | blackbox.com
NOTES
724-746-5500 | blackbox.com
Page 23
Chapter
Black Box Tech Support: FREE! Live. 24/7.
Tech support the
way it should be.
Great tech support is just 60 seconds away
at 724-746-5500 or blackbox.com.
About Black Box
Black Box provides an extensive range of networking and infrastructure
products. You’ll find everything from cabinets and racks and power and surge
protection products to media converters and Ethernet switches all supported
by free, live 24/7 Tech support available in 60 seconds or less.
© Copyright 2014. Black Box Corporation. All rights reserved.
AVSC-SDI-HDMI, version 1
724-746-5500 | blackbox.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement