Pyle Security System User Manual
1R / 4-BUTTON SERIES
VEHICLE SECURITY SYSTEM
System Operation
Button 1
Button 3
Button 2
Button 4
Standard Features:
Two 4-Button Remote Transmitters
Status indicator (LED)
Valet / override switch
Multi-tone siren
Dual stage impact detector
Remote panic
Remote chirp mute
Remote sensor bypass
Active or passive arming
Optional Features:
Starter disable
Flashing parking lights
Keyless entry
Remote trunk or hatch release
Illuminated entry
Anti-Carjacking
Hood and trunk protection
Remote auto start
Power window roll up
Back-up battery w/charging circuit
Glass break sensor
Note: Some features may require additional
parts and labor, and may not be appropriate
for certain vehicles. Consult your authorized
dealer.
ARMING OPERATION
To arm the system press transmitter button 1:
• The siren will chirp once.
• The parking lights will flash once.*
• The doors will lock.*
• The LED will turn solid for 10 seconds
then start flashing slowly. After 10
seconds the system is armed.
After Arming, if the system detects a bad
sensor or an open zone, the siren will chirp
and the parking lights will flash 4 times to
indicate a zone is open. The system will
ignore that input, but keep all other areas
protected.
While Armed, the system will trigger if:
• The doors are opened.
• The shock sensor detects an impact
to the vehicle.
• The hood or trunk is opened*.
When triggered, the siren will sound, the
horn will honk*, and the parking lights will
flash* for 30 seconds.
If the same input triggers the system 3 times
during a single arming cycle, the system will
bypass that input, keeping the other zones
protected, until the next time the system is
armed.
If the shock sensor detects a light impact to
the vehicle, the siren will chirp and the
parking lights will flash 5 times* to warn
away the potential intruder.
*Optional Feature
PASSIVE ARMING
The passive arming feature automatically
arms the system after closing all doors. The
Passive Arming feature requires the ignition
to have been on for at least 10 seconds
prior to exiting the vehicle. This enables the
key to be turned on then off quickly to
avoid passive arming in the event of
refueling, washing the vehicle, etc. The
Passive Arming feature may be enabled
during installation.
To arm the system passively:
1. Turn the ignition key off (make sure
ignition was on for at least 10
seconds).
2. Exit the vehicle and close all doors.
• Siren will chirp 1 time when last
door is closed.
• The LED flashes rapidly indicating
that the system is preparing to arm.
(The system can be armed any time
by pressing transmitter button 1.)
• If the optional countdown feature is
programmed, the siren will chirp
every 2 seconds until armed.
• The siren will chirp 30 seconds after
the last door is closed to indicate
the system is armed. NOTE: Opening
a door resets the passive arming
timer.
• The doors will lock.†*
†
If Passive Locking was enabled during installation.
DISARMING OPERATION
To disarm the system press transmitter
button 2.
• The siren will chirp twice.
• The parking lights will flash twice.*
• The doors will unlock.*
• The dome light will turn on for 30
seconds.*
TWO STAGE DISARM
If the alarm has been triggered
• Press button 2 will turn off siren/horn,
but alarm will remain armed.
• Press button 2 again.
• The siren will chirp 3 times.
• The parking will flash 3 times.*
• The doors will unlock.*
• The Dome light will turn on for 30
seconds.*
TAMPER ALERT
If the alarm was triggered while away from
the vehicle, the siren will chirp 3 times and
the parking lights will flash 3 times on
disarming for tamper indication.
AUTO REARM
The Auto Rearm feature allows the system to
automatically re-arm and lock the doors* in
the event the system is disarmed and a door
is not opened within 30 seconds. This
programmable feature may be enabled during
installation.
SILENT ARMING/DISARMING
Press transmitter button 3 to silently Arm or
Disarm the system for one-time operation.
The system can also be programmed for fulltime silent operation during installation.
IGNITION LOCK*
The ignition locking feature automatically
locks the doors 5 seconds after the ignition
key is turned on, and automatically unlocks
when the ignition key is turned off. To avoid
locking keys in the vehicle, the ignition
locking feature will be cancelled if a door is
open when the ignition is turned on. This
feature may be enabled during installation.
REMOTE PANIC
In the event of an emergency (PANIC)
situation, the system’s siren can be triggered
for 30 seconds to attract attention. To
activate the Panic Feature, press transmitter
button 1 for 2 seconds:
• The siren will sound.
• The horn will honk*
• The parking lights will flash*.
Press button 1 to exit panic mode and
rearm the system. Press button 2 to exit
panic mode and disarm system. The Panic
Feature will not operate when the ignition
is on.
*Optional feature
EMERGENCY OVERRIDE
If the transmitter becomes lost or fails to
operate, the system can be disarmed by
using the emergency override feature.
To override the system:
1. Enter the vehicle.
• The alarm will trigger.
2. Turn on the ignition key.
3. Press the Valet switch for 3 seconds.
• The siren will stop sounding.
• The starter defeat will be bypassed.
• The system will enter valet mode.
VALET MODE
When the system is placed into the Valet
Mode the security system will be disabled.
However, the optional keyless entry and
trunk release features will still function if
installed. The valet feature may be accessed
using the valet switch or using the remote
transmitter.
To enter or exit valet mode using the
switch:
1. Be sure the system is disarmed.
2. Turn the ignition key on.
3. Press and hold the valet switch for 3
seconds.
• The siren will chirp once to enter
valet or twice for exit.
• The LED will turn on solid indicating
the system is in valet mode, or turn
off indicating valet mode exit.
To enter or exit valet mode using the
remote:
1. Be sure the ignition key is off.
2. Press transmitter button 2 then button
1 and hold for 3 seconds.
• The siren will chirp once to enter
valet or twice for exit.
• The LED will turn on solid indicating
the system is in Valet Mode, or turn
off indicating Valet Mode exit.
OPTIONAL TRUNK RELEASE
Press button 4 for approximately 2 seconds
to open the trunk.
OPTIONAL TRUNK DISARM
The trunk disarm feature allows the alarm
to disarm automatically whenever
transmitter button 4 is used to activate the
optional trunk release. This eliminates
having to first disarm the alarm before
activating the trunk release. This feature
may be programmed during installation.
Optional Auxiliary 2 output
This programmable output can be used to
activate other accessories in your vehicle
(remote engine start, turn on headlights,
window roll up).
Pressing transmitter button 1 will arm the
system and activate 30 second output.
Press and Hold buttons 3 and 4 will activate
Auxiliary 2 output for as long as the buttons
are depressed
This feature may be programmed during
installation, and may require additional
parts, and labor.
REMOTE SENSOR BYPASS
To arm the system and bypass the shock
sensor, press button 1 to arm, then within 2
seconds press button 4. The siren will chirp
once and sensors will be ignored until the
system is disarmed and rearmed.
ANTI HIJACKING MODES*
You may select from 1-3 options:
1. Ignition Activated Anti Hijack Mode
Every time Ignition Key is turned on
system will enter Anti Hijack Mode.
2. Door Activated Anti Hijack Mode
When Ignition Key is on, and door is
opened, system will enter Anti Hijack
Mode.
3. When Ignition Key is on, press button
4 for 3 seconds, system will enter Anti
Hijack Mode.
The Anti Hijack Mode feature may be
programmed during installation
ANTI HIJACK OPERATION
After Anti Hijack has been triggered:
0-20 seconds there will be no indication
the Anti Hijack has been activated.
21-30 seconds LED will flash slowly.
31-45 seconds LED will flash quickly, and
STATUS INDICATOR (LED) FUNCTIONS
On Solid = Valet Mode
On Solid and not in valet = Open Zone
Slow Flash = System Armed
Rapid Flash when disarmed = Passive
Arming
siren will chirp every 2 seconds.
46-60 Seconds LED will flash quickly, and
siren will chirp every 1 second.
61 seconds, LED will flash quickly, Siren,
Horn* will sound, and Parking Lights will
flash for 5 minutes.
Starter Disable will be activated.
To deactivate the Anti Hijack during the first
60 seconds,
Press the Valet switch 3 times.
To deactivate the Anti Hijack after 60
seconds press, and hold the valet switch for
5 seconds
Siren, Horn* will stop sounding, and
Parking Lights*will stop flashing.
System will enter the valet mode.
Starter Disable will be deactivated.
PARKING LIGHT INDICATIONS
1 Flash = System Armed
2 Flashes = System Disarmed
3 Flashes = Tamper Alert
4 Flashes = Open Zone Indication (after
arming)
5 Flashes = Shock Sensor Warn-away
Installation Instructions
Before you begin the installation
• Read the INSTRUCTIONS!
• Always use a multi-meter when verifying
vehicle wiring.
• Before mounting the product, verify with
the customer the desired location for the
valet switch and LED.
• Protect the vehicle by using fender
covers.
• Always look before drilling. Make sure
you will not cause damage to vehicle hoses,
electrical looms or physical damage to
vehicle.
Mounting The System Module
Mount the system module under the dash
where it will be difficult for a potential thief
to locate the module, and away from
moving parts such as brake pedals, etc.
Route the antenna wire away from wire
looms, computer modules and metallic
objects for better range.
Mounting The Siren
Mount the siren in a suitable place under
the hood, away from hot and moving
engine parts such as manifolds, fan belts,
etc. Make sure the siren cannot be
accessed from underneath the vehicle or
through the grill. Face the siren down so
that water cannot accumulate inside the
siren bell. Protect wires running through
the firewall using either tape or split loom
tubing. If a new hole is needed, protect the
wire from chaffing by installing a proper
size grommet.
Mounting The Shock Sensor
Secure the shock sensor to the steering
column, thick wire harness or a dash brace,
using a wire tie. Make sure that the
adjustment screw is accessible for later
testing and adjustment.
12-Pin Main Harness:
• RED WIRE - +12V Battery input. Connect
the red fused wire on the main harness to a
constant +12V source. This source wire
should be at least 15 amp supply.
• BLACK WIRE - Ground input (-). Connect
to a solid chassis ground that is clean and
free of paint or dirt.
• YELLOW WIRE - +12V Ignition input.
Connect to a main ignition wire at the
ignition switch harness. This wire shows
+12V when the ignition is on and while
cranking. The voltage must not drop when
the car is starting.
• GREEN WIRE - Negative door trigger (-).
Connect to the door switch circuit wire that
shows ground when the door is open.
• VIOLET WIRE - Positive door trigger (+).
Connect to the door switch circuit wire that
shows +12V when the door is open.
• BLUE WIRE - Trunk/Hood trigger (-).
Connect the Blue wire to the trunk and/or
optional hood pin switches.The switch must
provide a ground output when switch is
opened.
• BROWN WIRE - Siren wire output (+) 3A.
Connect to the siren’s red wire. Connect the
siren’s black wire to ground.
• BROWN/WHITE WIRE – 2nd Auxiliary
Output 500mA (-) can be programmed for:
pulsing Horn output, variable pulse output,
or 30 second output.
Connect to an optional relay to activate
these accessories.
• BLACK/WHITE WIRE - Dome Light output
(-) 500mA. Connect to an optional relay to
activate the vehicle’s dome light.
• ORANGE WIRE - Armed Output (-) 500mA.
The ORANGE wire provides a ground when
the unit is armed to activate a circuit disable
relay or other device (i.e. window control
module, etc.).
• GRAY WIRE - Auxiliary output (-) 500mA.
Connect to a relay for an optional feature
such as trunk release, etc.
• WHITE WIRE - Parking Light output (+/-)
10A relay. Connect to the vehicle’s parking
light wire. If the vehicle’s parking light
circuit exceeds 10 amps a relay is required.
For vehicle’s with independent left and
right parking light circuits, the parking light
wires must be connected using diodes to
keep the circuits separate.
NOTE: Do not connect the WHITE wire to
the vehicle’s headlight circuit.
RED/WHITE WIRE – Parking Light Polarity
Selection Input. Connect this wire to +12V
Constant for Positive Output on White wire.
Connect to Ground for Negative Output on
White wire. For Multiplex activated parking
light systems, install correct value resistor
on this wire.
Plug in Connectors
3-Pin Red Door Lock Connector: Plug-in
connector port for door lock harness or
optional door lock relay module.
• BLUE WIRE - unlock output (-) 500mA.
• GREEN WIRE - lock output (-) 500mA.
2-Pin White Connector: Plug-in connector
port for LED. Mount the LED in an area
where it can easily be seen from either the
driver or passenger side of the vehicle.
2-Pin Blue Connector: Plug-in connector
port for valet switch. Mount switch in an
area that is easily accessible from the driver’s
seat.
4-Pin White Connector: Plug-in connector
port for dual stage shock sensor.
Entering Programming
To enter System Programming:
1. Turn Ignition on.
2. Within 5 seconds press the valet switch
5 times.
The siren will emit a long chirp, to indicate
entering the program mode.
3. Press the valet switch the number of
times equal to the desired feature step.
The siren will chirp, and the Led will flash
to confirm your selection
(example: Step 7 = 1 long chirp, and 2 short
chirps. LED will emit 1 long flash, and 2
short flashes.)
4. Within 5 seconds, press the transmitter
button corresponding to the desired
operation mode for that feature.
The siren will chirp, and LED will flash to
indicate the setting.
One chirp/flash = Button 1
Two chirps/flashes = Button 2
Three chirps/flashes = Button 3
Four chirps/flashes = Button 4
Turn off Ignition to save changes.
Siren will chirp 3 times.
Parking Lights will flash 3 times
Complete Default Reset
This procedure will reset all Programmable
Features to factory default settings.
1. Enter System Programming.
2. Press valet switch 16 times. Siren will
emit 3 long chirps, and 1 short chirp
LED will emit 3 long, and 1 short flashes.
3. Press button 4 for 3 seconds.
Siren will chirp 6 times.
Parking Lights will flash 6 times
LED will flash 3 times.
3. Turn Ignition off to save changes
Siren will chirp 3 times
LED will flash 3 times
Parking Lights will flash 3 times
Programmable Features
1. Arming Mode. Select between manual
arming (Active), automatic arming (Passive),
and automatic arming with chirps that
countdown every 2 seconds until armed.
2. Parking Light Operation. Selects
whether the parking lights flash twice or
remain on for 30 seconds after disarming
the system.
3. Auto Rearm. Automatically rearms the
system in case of accidental disarming. The
hood/trunk must not be opened or auto
Programmable Features
Step Function
1. Arming Mode
2. Parking Light Operation
3. Auto Rearm
4. Arming Chirps
5. Trunk Disarm
6. Ignition Locking
7. Door Lock Pulse
8. Passive Locking
9. Door Unlock Pulse
10. Open Zone Report
11. Auxiliary 2
12. Not Used
13. Ignition Anti-Hijack
14. Door Anti-Hijack
15. Remote Anti-Hijack
16. Factory Default Reset
Button 1
Active
Flash twice
Off
Normal
Off
On
0.8 sec.
Off
Single
10 seconds
Siren Horn
rearm is bypassed. If button 3 is selected,
the doors will lock on auto rearm.
4. Arming Chirps. Select Normal or Silent
Arming.
5. Trunk Disarm Feature. When selected,
activating the Auxiliary function to open
the trunk will automatically disarm the
system.
6. Ignition Locking. Automatically locks
and unlocks the doors with the ignition.The
system will not lock the doors if any door is
open when the ignition is turned on.
7. Door Lock Pulse. Selects between a 0.8second and a 3.5-second output for
vehicles equipped with vacuum door
locking systems.
8. Passive Locking. Selects whether or not
the system will automatically lock the doors
when Arming.
9. Door Unlock Pulse - Single or Double.
Selects between a single pulse or a double
pulse door unlock output.
10. Open Door Report. Siren will chirp 4
Button 2
Passive
30 sec.
Auto Rearm
Silent
On
Off
3.5 sec.
On
Double
60 sec.
Horn
Button 3
Passive w/Countdown
Button 4
Auto Rearm w/ Lock
Variable output
30 sec. output
Off
On
Off
On
Off
On
All Programmable options will reset to factory default settings
times if a door remains open 10 seconds
after arming. If vehicle has delayed dome
light, program for 60 seconds.
11. Auxiliary 2.
Select Siren/Horn (Default) Horn will sound
when alarm is triggered.
Select Horn. Horn will sound with arm,
disarm, shock sensor warn-away, and
trigger.
Select Variable. Auxiliary 2 output will be
activated for as long as you hold buttons 3,
and 4.
Select 30 sec. output. Auxiliary 2 output will
be activated 30 seconds upon arming
system.
12. Not used
13. Ignition Anti-Hijack. Every time Ignition
is turned on. Anti-Hijack Function will be
activated.
14. Open Door Anti Hijack. Whenever any
door is opened with Ignition on. Anti-Hijack
Function will be activated.
15. Remote Anti Hijack.When Ignition is on,
and Button # 4 is pressed for 3 Seconds.
Anti-Hijack Function will be activated.
16. Resets all programs to factory default
settings.
Test System and Adjust Shock Sensor
Arm and disarm system, checking that the
siren chirps and parking lights are
functioning normally. Make sure that the
programmed features are performing
correctly, ie.: ignition locks, passive arming,
passive locks, etc.
Test the doors and hood/trunk inputs
(make sure all doors trigger the system, not
just the driver’s door).
Adjust the shock sensor.
Arm the system and try starting the vehicle,
it should not start.
Arm the system and disarm it using the
emergency override feature.
If programmed for passive arming make
sure that the system arms properly.
Tie up wire harness, and replace any under
dash panels.
Make sure the customer has physical
knowledge of the location of the
valet/override switch.
Adding Transmitters
To add a new transmitter to the system
have the desired transmitters ready and
follow the Code Learning sequence.
To enter Code Learning Mode:
1. Turn the ignition on, off, on, off and
leave on.
• The siren will chirp once.
2. Press and hold the Valet switch for 5
seconds.
• The siren will chirp 3 times.
3. Press the Lock Button on the transmitter.
• The siren will chirp once.
4. Repeat step 3 for each additional
transmitter, up to four total transmitters.
5. Turn off the ignition.
• The siren will chirp 3 times.
NOTE: If a transmitter is lost or stolen, make
sure to code all 4 transmitter memory
locations. (Example: If only one transmitter
is used, repeat step-3 three more times to
remove any previously programmed
transmitters.)
DOOR LOCK WIRING DIAGRAMS
NEGATIVE TRIGGER
POSITIVE TRIGGER
SWITCH
(+) LOCK
L
SWITCH
L
DOOR LOCK
RELAYS
(-) UNLOCK
UL
LOCK/UNLOCK
SWITCH
86 87 85
87a
GREEN
LOCK/UNLOCK
SWITCH
DOOR LOCK
RELAYS
(+) UNLOCK
UL
(-) LOCK
30
+12V
GREEN
86 87 85
87a
BLUE
BLUE
30
ADDING ACTUATORS
REVERSE POLARITY
SWITCH
L
+12V
+12V
AFTER-MARKET
ACTUATORS
86 87 85
87a
GREEN
87
BLUE
86
87a
X
85
CUT
LOCK/UNLOCK
SWITCH
30
30
87
86 87 85
87a
BLUE
UL
GREEN
86
87a
CUT
85
FACTORY DOOR
MOTOR
X
30
30
VACUUM SYSTEM
RELAY WIRING DIAGRAMS
VACUUM PUMP
POSITIVE TRIGGER
87
BLUE
86
87a
NEGATIVE TRIGGER
85
30
TO WIRE IN VEHICLE
+12V
TO WIRE IN VEHICLE
CUT
SWITCH
87
GREEN
86
87a
30
85
L
(-) OUTPUT
FROM ALARM
86 87 85
87a
(-) OUTPUT
FROM ALARM
86 87 85
87a
30
30
UL
LOCK/UNLOCK
SWITCH
+12V
+12V
WIRING DIAGRAM
SHOCK
SENSOR
BLUE
GREEN
LED
VALET
RED/WHITE
RED
GREEN
BLACK
VIOLET
YELLOW
BLUE
BROWN
BROWN/WHITE
BLACK/WHITE
LIGHTS
ORANGE
GRAY
WHITE
TO BATTERY (+)
PARKING
LIGHT
POLARITY
(+/-)
ARMED
OUTPUT -
IGNITION (+)
AUXILIARY -
HORN
DOME LIGHT
SIREN
TRUNK/
HOOD
DOOR
DOOR
+12V
PYLE SECURITY
CAR SECURITY SYSTEM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement