AUSTRALIAN MONITOR | XRS Series | Specifications | AUSTRALIAN MONITOR XRS Series Specifications

AUSTRALIAN MONITOR XRS Series Specifications
SERVICE INFORMATION
XRS12P
POWERED LOUDSPEAKER
CONTENTS:
OPERATION MANUAL
SCHEMATIC DIAGRAM
Australian Monitor
1 Clyde Street, Silverwater NSW 2128 Australia
+61 2 9647 1411
www.australianmonitor.com.au
XRS SERIES
POWERED AND PASSIVE LOUDSPEAKERS
INSTALLATION AND OPERATION MANUAL
IMPORTANT SAFETY INFORMATION
1.
Save the carton and packing material even if the equipment has
arrived in good condition. Should you ever need to ship the unit, use
only the original factory packing.
2.
Read all documentation before operating your equipment. Retain
all documentation for future reference.
3.
Follow all instructions printed on unit chassis for proper operation.
4.
Do not spill water or other liquids into or on the unit, or operate
the unit while standing in liquid.
5.
Make sure power outlets conform to the power requirements listed
on the back of the unit.
6.
Do not use the unit if the electrical power cord is frayed or broken.
The power supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against them,
paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7.
8.
9.
Always operate the unit with the AC ground wire connected to the
electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
Mains voltage must be correct and the same as that printed on the
rear of the unit. Damage caused by connection to improper AC voltage
is not covered by any warranty.
Have gain controls on amplifiers turned down during power-up
to prevent speaker damage if there are high signal levels at the inputs.
10 Power down and disconnect units from mains voltage before making
connections.
13. Do not block fan intake or exhaust ports. Do not operate equipment
on a surface or in an environment which may impede the normal flow
of air around the unit, such as a bed, rug, weathersheet, carpet,
or completely enclosed rack. If the unit is used in an extremely dusty
or smoky environment, the unit should be periodically “blown free”
of foreign matter.
14. Do not remove the cover. Removing the cover will expose you
to potentially dangerous voltages. There are no user serviceable
parts inside.
15. Do not drive the inputs with a signal level greater than that required
to drive equipment to full output.
16. Do not connect the inputs / outputs of amplifiers or consoles to any
other voltage source, such as a battery, mains source, or power supply,
regardless of whether the amplifier or console is turned on or off.
17. Do not run the output of any amplifier channel back into another
channel’s input. Do not parallel- or series-connect an amplifier output
with any other amplifier output. Australian Monitor is not responsible
for damage to loudspeakers for any reason.
18. Do not ground any “hot” (red) terminal. Never connect a “hot” (red)
output to ground or to another “hot” (red) output!
19. Non-use periods: the power cord of equipment should be unplugged
from the outlet when left unused for a long period of time.
20. Service Information Equipment should be serviced by qualified service
personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment
11. Never hold a power switch in the “ON” position if it won’t stay
there itself!
C. The equipment has been exposed to rain
12. Do not use the unit near stoves, heat registers, radiators, or other heat
producing devices.
D. The equipment does not appear to operate normally, or exhibits a
marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL
INTRODUCTION AND CONTENTS
Building on the reliability and sonic quality of the very popular XR speaker
series, Australian Monitor brings you the AM Pro XRS two way injection moulded
speaker enclosures with more features and new aesthetic to suit both live
sound reinforcement and permanent installation. From Front of House to fold
back, the dance floor to background fill, the XRS series with both passive and
powered options are designed with flexibility and performance in mind.
The AM Pro XRS range includes 8”, 10” and 12” models all with high quality
compression drivers and represent a significant advancement in injection
moulded box design while maintaining excellent audio quality and great value
for money.
INTRODUCTION
3
FRONT AND REAR PASSIVE PANEL
4
REAR POWERED PANEL
5
SPECIFICATIONS
6
AUS, EUR, USA
REV A 24th Nov 2008
CAUTION
This symbol is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the products enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK),
NO USER SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of important
operational and maintenance (servicing) instructions in the literature
accompanying the appliance.
Caution:
WARNING!
To prevent electric shock do not use this (polarised) plug with an extension
cord, receptacle or other outlet unless the blades can be fully inserted to
prevent blade exposure. To prevent electric shock, match wide blade of
plug to wide slot, fully insert.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
XRS SERIES INSTALLATION AND OPERATION MANUAL
PAGE 3
FRONT AND REAR PANEL PASSIVE VERSION
1
2
1 High Frequecy Driver
1
XRS8 shown here
1 Speaker Input
Horn loaded compression driver. Directivity 90deg x 90deg.
Passive crossover in the XRS8/10/12.
XRS8/XRS8P 1.5”
XRS10/XRS10P 1.5”
XRS12/XRS12P 2”
The input connector is a 4 pole speakon compatible connector.
Pins 1+ and 1- are wired to the +ve and -ve respectively of
the speaker. The XRS10 and XRS12 have 2 connectors. They
are wired in parallel so either connector can be used as an
input, the other as a loop through.
Active crossover and power amp in XRS8P/10P/12P.
XRS8P 50W
XRS10P 50W
XRS12P 100W
Accessories:
XRS8/XRS8P
XR8PMA Pole mount adapter
XR8UMB Universal mounting bracket
2 Low Frequency Woofer
Driver sizes:
XRS8/XRS8P 8”
XRS10/XRS10P 10”
XRS12/XRS12P 12”
Active crossover and power amp in XRS8P/10P/12P.
XRS8P 100W
XRS10P 100W
XRS12P 300W
Note that the XRS8 ships as a pair.
PAGE 4
XRS10/XRS10P
XR10CVR Heavy duty cover
AMISLSB1 Wall mount brackets
ATC303 Tripod speaker stand
ATC304 Heavy duty tripod speaker stand
ATC305 Winch up speaker stand
XR10-12UB Universal bracket
XRS12/XRS12P
XR12CVR Heavy duty cover
AMISLSB1 Wall mount brackets
ATC303 Tripod speaker stand
ATC304 Heavy duty tripod speaker stand
ATC305 Winch up speaker stand
XR10-12UB Universal bracket
XRS SERIES INSTALLATION AND OPERATION MANUAL
REAR PANEL POWERED VERSION
7 10 2
8 11 4
9 12 6
1 MIC IN
This is a balanced XLR microphone input.
10 Line LEVEL
This controls the level of the LINE input.
(3)
2 Mic SIGNAL
11 Line BASS
This is a green LED signal present
indicator for the Mic input. It indicates
signal present on the input and is not
affected by the level control.
1
3
5
3 LINE IN
This is a balanced XLR line level input.
4 Line SIGNAL
This is a green LED signal present
indicator for the Line input. It indicates
signal present on the input and is not
affected by the level control.
5 LINE OUT
The LINE OUT is on an XLR connector.
This output can be connected to the LINE
IN on another XRS Powered speaker to
expand the system.
6 Output CLIP
This is a red LED clip indicator for the
mixed mic and line audio signal. Some
flashing of red is acceptable on program
transients. Continuous flashing of red
could be placing undue stress on the
speaker and will sound distorted. Turn
down the input level until the clip LED is
no longer lit.
7 Mic LEVEL
15
13 14
This controls the level of the MIC input
(1).
8 Mic BASS
This is the bass control for the MIC input
(1). There is 12dB of cut and boost at
100Hz. This EQ is the shelving type.
9 Mic TREBLE
This is the treble control for the MIC input
(1). There is 10dB of cut and boost at
10kHz. This EQ is the shelving type.
XRS SERIES INSTALLATION AND OPERATION MANUAL
This is the bass control for the LINE input
(3). There is 12dB of cut and boost at
100Hz. This EQ is the shelving type.
12 Line TREBLE
This is the treble control for the LINE
input (3). There is 10dB of cut and boost
at 10kHz. This EQ is the shelving type.
13 Power Switch
This switch turns the power on or off to
the unit.
14 IEC Mains Input Socket
This is a standard IEC 3 pin socket.
It accepts a standard IEC mains cable,
(provided). The fuse draw contains the
mains fuse and a spare.
The mains fuse is a time lag (slow blow)
HRC 20mm x 5mm ceramic or glass type
fuse.
XRS8P
XRS10P
XRS12P
2.5A
2.5A
5.0A
IMPORTANT: Always replace the
fuse with one of the same value and type.
NOTE: Always disconnect power to
the amplifier before replacing fuses.
15 Voltage Select Switch
This switch is used to select the mains
voltage for your region. Select either
230V or 115V.
IMPORTANT: Disconnect power to
the amplifier before operating this switch.
IMPORTANT: Make sure this setting
is correct before connecting the unit to
the mains.
PAGE 5
SPECIFICATIONS
XRS8P
Drivers
XRS10P
XRS12P
1 x 8” woofer
1 x 10” woofer
1 x 12” woofer
1 x 1.5” HF driver
1 x 1.5” HF driver
1 x 2” HF driver
Frequency Response(-3dB)
65Hz-18kHz
55Hz-18kHz
50Hz-18kHz
Frequency Response(-10dB)
55Hz-18kHz
50Hz-18kHz
40Hz-20kHz
118dB
121dB
125dB
Bass control @ 100Hz
12dB
12dB
12dB
Treble control @ 10kHz
10dB
10dB
10dB
100W(low) + 50W(high)
100W(low) + 50W(high)
300W(low) + 100W(high)
Line
0.02%
0.02%
0.02%
Microphone
0.04%
0.04%
0.04%
90° x 90°
90° x 90°
90° x 90°
Peak Sound Level(dB 1m)
Tone controls
Output Power
Distortion (THD)
Tweeter Dispersion(HxV)
Input Impedance
Line
20kOhm
20kOhm
20kOhm
Microphone
10kOhm
10kOhm
10kOhm
Connectors
XLR 3
XLR 3
XLR 3
AC 115V/230V, 50/60Hz
AC 115V/230V, 50/60Hz
AC 115/230V, 50/60Hz
Dimensions(WxDxH)
277 x 265 x 407mm
325 x 308 x 478mm
415 x 391 x 600mm
Packing Dimensions(WxDxH)
355 x 325 x 470mm
375 x 355 x 535mm
465 x 435 x 680mm
Net Weight
8.6kg
10.5kg
23kg
Gross Weight
10.1kg
11.8kg
25.2kg
Power Supply
PAGE 6
XRS SERIES INSTALLATION AND OPERATION MANUAL
SPECIFICATIONS
XRS8
XRS10
XRS12
1 x 8” woofer
1 x 10” woofer
1 x 12” woofer
1 x 1.5” HF driver
1 x 1.5” HF driver
1 x 2” HF driver
Frequency Response(-3dB)
65Hz-18kHz
55Hz-18kHz
50Hz-18kHz
Frequency Response(-10dB)
60Hz-20kHz
50Hz-20kHz
40Hz-20kHz
Sensitivity(dB 1W 1m)
92 dB
95 dB
97 dB
Impedance
8 Ohm
8 Ohm
8 Ohm
Recommended Max Power(Wrms)
100 W
250 W
300 W
Max Sound Level(dB 1m)
118dB
125dB
128dB
90° x 90°
90° x 90°
90° x 90°
1%
1%
1%
1
2
2
Dimensions(WxDxH)
277 x 257 x 400mm
321 x 321 x 464mm
415 x 382 x 620mm
Packing Dimensions(WxDxH)
595 x 310 x 460mm
375 x 355 x 535mm
465 x 435 x 680mm
6.5kg
10kg
18kg
15kg (pair)
12kg
20kg
Drivers
Dispersion(HxV)
Harmonic Distortion
Speakon compatible connectors
Net Weight
Gross Weight
XRS SERIES INSTALLATION AND OPERATION MANUAL
PAGE 7
AUSTRALIA AND NEW ZEALAND
www.australianmonitor.com.au
SYDNEY
MELBOURNE
ADELAIDE
AUCKLAND
(NSW SALES)
(VIC & TAS SALES)
(SA & NT SALES)
(NZ SALES)
1 Clyde Street
Silverwater
NSW 2128
Private Bag 149
Silverwater NSW 1811
Phone: (02) 9647 1411
Fax: (02) 9648 3698
Email:
nsw@audiotelex.com.au
22/277
Middleborough Road
Box Hill VIC 3128
PO Box 151 Blackburn
South VIC 3130
Phone: (03) 9890 7477
Fax: (03) 9890 7977
Email:
vic@audiotelex.com.au
31 Walsh Street
Thebarton
SA 5031
PO Box 157
Hindmarsh SA 5007
Phone: (08) 8352 4444
Fax: (08) 8352 4488
Email:
sa@audiotelex.com.au
9C Piermark Drive
Albany 0752
New Zealand
PO Box 300-512
Albany 0752
Phone: (09) 415 9426
Fax: (09) 415 9864
Email:
nz@hillssvl.co.nz
CANBERRA
BRISBANE
PERTH
(ACT SALES)
(QLD SALES)
(WA SALES)
1st Floor,
Campion Street
Deakin ACT 2600
PO Box 109
Deakin West ACT 2600
Phone: (02) 6260 4544
Fax: (02) 6260 4744
Email: gordon.anderson@
hillssvl.com.au
42 Commercial Road
Fortitude Valley
QLD 4006
PO Box 2578 Fortitude
Valley BC QLD 4006
Phone: (07) 3852 1312
Fax: (07) 3252 1237
Email:
qld@audiotelex.com.au
3/11 Howe Street
Osborne Park WA 6017
PO Box 1281
Osborne Park BC
WA 6916
Phone: (08) 9204 0200
Fax: (08) 9244 3783
Email:
wa@audiotelex.com.au
EUROPE / ASIA / MIDDLE EAST
www.australianmonitor.com.au
INTERNATIONAL SALES
1 Clyde Street Silverwater NSW 2128 Australia
Private Bag 149 Silverwater NSW 1811
Phone: + 61 2 9647 1411
Fax: + 61 2 9748 2537
Email: international@audiotelex.com.au
1
2
3
4
5
6
7
8
9
10
12
11
D
D
Q33
TIP121
R152
+40V
47 2W
Q37
J108
MUTE
4
30Vac
CF8
DB1
KBU1004
60Vac
CF9
变压器
1
C22
220n
1
230V
Q34
BC560
R139
4M7
-40V
C62
6800U/50V
DB2
KBU1004
D44
1N4148
1N4148
Q38
J108
MUTE
R142
10M
R141
100K
-80V
R154
4K7
Q36
BC560
R144 C66
56K 470nJ63
R153
100K
C67
100n
C70
220U/25V
R151
2K2
C64
100n
CZ03
6P(2.5MM)
R150
10K
R143
C5
123
C1
10U/25V-NP
-15V
Q35
TIP126
47 2W
2R2
R1
10K
F3
+40V
+80V
5AF
R11
390
R60
2K2
C8
R10
2K2
R18
100n
2
3
IC1A
JRC4558
D24
1N4007
R85
1R52
560
MUTE
LOW-IN
R69
1K
R68
470
R82
0R33 5W
R76
47
COUT
30U/100V
R57
4UH
R84
6K8
5
R74
1K8
Q20
BC550
R70
1K
R81
0R33 5W
DL4
GREEN
R1 JRC4558
47K
C1
1nJ100
0R33 5W
D23
1N4007 R59 C30 33P
2K2
R86
0R33 5W
-15V
R75
R73
1K
D27
1N4148
560
D4
6K8
Q6
BC550
R37
1K8
Q5
R22
BC560 1K
CT04
7P*100MM(2.5MM)
-15V +15V
C17
334
7R26
1K2
2
1
LOW
3
IC5A
C18 JRC4558
333
R27
1K2
C16
333
1K
C13
104
R35
Q2
A92
3
1
R21
100K
R28
27K
+15V
R22
1K
2
2
IC1A
JRC4558
1
2
3
4
5
6
7
C19
1U/50V
R5
3
CF1
2K2
D3
1N4148
C20
1U/50V
IC4A
JRC4558
R32
R31
1M
R33
D2
1M
R34
1N4148
10K
R30
R29
10K
6
D1
7
47K
2
1
5
C
3
1N4148
IC6B
JRC4558
10K
R46
IC6A
JRC4558
+15V
C11
100n
R15
560
R8
2K2
D7
BAV21
R43
C29
CV9
104
CV11
104
2R17
B
Q1
A92
2K2
1N4148
R18
1M
CV2
104
CV4
104
CV6
104
IC2C
JRC4558
IC1C
JRC4558
IC6C
JRC4558
CV8
104
IC3C
JRC4558
CV10
104
IC4C
JRC4558
C10
2.2U/50V
D6
1N4148
R14
R13
1M
R15
D5
10K
1M
R16
1N4148
R12
R11
10K
6
D4
7
39K
1
12K
3
5
1N4148
IC3B
JRC4558
10K
C9
104
2R10
IC3A
JRC4558
CV12
104
IC5C
JRC4558
DZ2
12V
D17
1N4148
F2
Q3
2N5401
C20
100n
F4
CV7
104
DZ4
12V
R27
100
R14
390
D20
MR854
6.3AF
Q14
2SC4793
R13
2K2
C15
22u/16V
-40V
Q10
2SA1943
3R3 1/2W
C9
R16
22P/500V
D8
1N4148
R63
2K2
-15V
Q8
E15031
CV5
104
CF2
C14
100n
R34
22
D18
1N4148
CV3
104
CV13
100U/50V
2K2
R38
180K
D13
1N4148
R36
1K
+15V CV1
104
R40
0R15 5W
R24
Q18
2N5401
100n
R39
0R15 5W
4UH
R33
4R7 5W
Q1
2N5401
C32
22P/500V
Q25
2N5551
390
L1
C7
R6
2K2
-15V
R64
C3
102
C14
22P
R23
IC5B
JRC4558
R25
1K2
C12
684
DZ1
12V
R9
8K2
IC2A
JRC4558
10K
R20
5K6
1
R44
47
DL2
GREEN
R2
47K
1K2
C2
183
22U/16V
5
D7
100P
R9
2K2
1N4007
Q28
2SA1837
R66
560
MUTE
R3 10K
4K7
6
6
R48
C17
100u/63V
CF4
Q22
TIP36C
3R3 1/2W
100
C33
47nJ100
R71
22
D32
1N4148
R58
2K2
D26
BAV21
R83
47K
2K2 1/2W
Q26
BC560
C26
100n
R55
2K2
R20
470
R36
8K2
C15
154
7R24
4R7 5W
1N4007
R47
7R49
C19
+40V
D5
C4
100n
R79
R65
560
Q16
2N5401
SIGN A2
C27
100U/63V
68P
6
D21
MR854
R38
R4
100K
2K2
R21
1K
D12
1N4007
C12
1nJ100
R35
22
R23
Q13
BC550
33K C6
IC1B
6.3AF
Q9
2SC5200
3R3 1/2W
R42
180K
D11
1N4007
R5
2K2
R41
C3
100n
R3
2K2
DL1
GREEN
330
DZ3
12V
Q7
E15030
R45
D6
1N4148
Q2
2N5551
R4
10K
R80
L2
560
C21
1nJ100
C24
100n
CF3
BAV21
R17
D1
2K2 1N4007
R7
2K2
-15V
R72
22
2K2 1/2W
D31
1N4007
C25
68P
4
3R3 1/2W
Q21
BC550
R54
2K2
15K
R50
47K
D30
1N4007
D19
1N4148
+15V
C2
100n
Q23
TIP35C
F1
R37
3K3
D14
1N4148
R7
8K2
3
123
1
DL3
GREEN
R78
C23
100n
R51
2K2
Q17
2N5551
R53
10K
Q27
2SC4793
R77
D25
1N4148
100
C10
22P/500V
R19
10K
C4
22P
6
4
HIGH-IN
100
BAV21
R67
D22
2K2 1N4007
C5
100n
IC1C
JRC4558
Q4
2N5551
R29
4K7 3W
IC4B
JRC4558
5
7
8
C
Q19
2N5551
C16
680P
R26
IC1B
JRC4558
4
R62
+15V
R56
2K2
D9
1N4148
D10
8
C31
22P/500V
Q12
IRFP140
8
D28
1N4148
D29
D3
1N4007
2R2 2W
Q15
2SA1837
R12
+15V
123
HIGH
1
C8
IC2B 153
JRC4558
C11
10U/25V-NP
5
100K
4
Q24
2N5401
R2
R25
47
8
C28
100n
4
R61
390
C7
7
C6
5
R145
-40V
R8
4K7 2
R6
4K7 6
-15V+15V
-15V
GND
+15V
HIGH-IN
LOW-IN
LIMIT
6
5
4
3
2
1
EC
2
3
4
C65
100n
8
2
CF17
10n/2KV
+40V
C60
6800U/50V
C61
6800U/50V
0V
CF7
SW
C68
220U/25V
C69
10U/63V
4
30Vac
CF6
T2.5A
100K
R147
4K7
8
3
3
CF16
F
DZ5
15V
D45
R140
C63
2R2
R148
2K2
R149
100
4
POWER INPUT
CF5
+15V
8
+80V
C59
6800U/50V
60Vac
TR
R146
Q11
IRFP9140
R30
4K7 3W
330
C13
1nJ100
C18
680P
R19
D2
1N4007
R28
47
2R2 2W
-40V
-80V
5AF
D1
1N4148
R3
30K
C5
22P
IC1B
15K
C1
TREBLE
IC4A
JRC4560
R2
7K5
560
10U/25V-NP
R9
1M
C3
472
D4
1N4148
-15V
J1
R10
10K
1
3
C4
103
R1
10K
A50K
R2
15K
15K
C5
103
R8
15K
RP2
B50K BASS
7
5
C8
10U/25V-NP
R7
IC4B
JRC4560
CON2
5044
10K
+15V
1K5
R28
150K
3
1
CV7
104
+15V
IC4C
JRC4560
C10
10U/25V-NP
R8
D8
1N4148
-15V
4
-15V
C4
473
D9
IN4148
CV8
104
47
R22
OPT1 22P
LCR0202
10K
RP1-1
CV5
104
IC3C
JRC4560
CV6
LED2 104
GREE
+15V
1K5
R29
150K
C13
22P
R6
5K1
6
R15
10U/25V-NP
C17
7
5
10K
C15
10U/25V-NP
22P
B
IC2B
JRC4560
R14
RP1-3
2
1
R27
CV3
104
IC2C
10U/25V-NP
JRC4560
R10
30K
R17
10K
R13
3
IC2A
JRC4560
2N5551
R12
10K
3
100K
1
RP1-1
47
CON3
5040
LIMIT
C22
R26
-15V
R25
C14
IC1A
SIN-OUT
10K
C12
22P
-15V
C9 +15V 3
47P
D7
1N4148
2
LED1
GREE
C16
R16
1
2
RP2-3
10K
Q3
5K1
D5
1N4148 R9
30K
2
10PIN2.54mm
R20
JRC4560
10U/25V-NP
C21
22P
+15V
R5
+15V
8
C6
22P
6
R7
-15V
C6
22P
D6
1N4148
RP1
OUT1
22P
2
RP1-3
RP1-1
RP1-3
RP1-1
1
2
3
4
5
6
7
8
9
10
R21
10K
10K
C19
10U/25V-NP
R11
R4
30K
IC3A
JRC4560
3
C20
7
8
10K
7K5
IN2
JRC4560
IC3B
5
R19 10K 6
R24 3K3
+15V
CV1
104
IC1C
2K2
LED3
RED
CV8
JRC4560 100U/50V
JRC4560
J2A
Q1
100
Q2
2N5551
2N5401 R23
100K
CV4
104
1
2
3
4
5
6
7
8
9
10
RP2-1
RP2-3
CV2-15V
104
J1A
IN2
10PIN2.54mm
4
R4
C18
10U/25V-NP
R18
8
R3
IN1
10U/25V-NP
8
C3
RP2-1
5
1
C2 -15V
47P +15V
4
1
R6
3
B
RP3
B50K
D3
1N4148
2
R5
C7
7
2
6
4
560
+15V
D2
1N4148
C1
10U/25V-NP
R1
CON1
5044
-15V
+15V
1
2
3
4
5
6
7
8
9
10
CT01A
CT01
RP1-3
5
4
3
2
1
IN1
-15V
-15V
-15V
GND
+15V
SIN-OUT
LIMIT
5P*100MM(2.5MM)
1
2
3
4
5
6
LIMIT
SIN-OUT
+15V
GND
-15V
6P*100MM(2.5MM)
+15V
10PIN2.54mm
+15V
Q4
C11
473
D10
IN4148
2N5551
A
A
Australian Monitor
XRS12P
1
2
3
4
5
6
7
8
9
10
11
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising