Welch Allyn | SCANTEAM 5770 LASER | Specifications | Welch Allyn SCANTEAM 5770 LASER Specifications

Welch Allyn SCANTEAM 5770 LASER Specifications
CORDLESS SCANNING SYSTEM
SCANTEAM® 2070 BASE
IMAGETEAM™ 3870 LINEAR IMAGER
SCANTEAM® 5770 LASER
Quick Start
Disclaimer
Welch Allyn Data Collection, Inc. (d/b/a Hand Held Products) reserves the right to make
changes in specifications and other information contained in this document without prior
notice, and the reader should in all cases consult Hand Held Products to determine
whether any such changes have been made. The information in this publication does not
represent a commitment on the part of Hand Held Products.
Hand Held Products shall not be liable for technical or editorial errors or omissions
contained herein; nor for incidental or consequential damages resulting from the
furnishing, performance, or use of this material.
This document contains proprietary information which is protected by copyright. All rights
are reserved. No part of this document may be photocopied, reproduced, or translated
into another language without the prior written consent of Hand Held Products.
 2000 Welch Allyn Data Collection, Inc. All rights reserved.
Web Address: www.handheld.com
The CE mark on the product indicates that the system has been tested to and
conforms with the provisions noted within the 89/336/EEC Electromagnetic
Compatibility Directive and the 73/23/EEC Low Voltage Directive.
For further information please contact:
Hand Held Products (UK) Ltd.
1st Floor
Dallam Court Dallam Lane
Warrington, Cheshire WA2 7LT
England
Hand Held Products shall not be liable for use of our product with equipment (i.e., power
supplies, personal computers, etc.) that is not CE marked and does not comply with the
Low Voltage Directive.
C.S.A. Statement
This product must be used with a certified Class 2 Power supply or be
powered by a certified SELV (Safety Extra Low Voltage) output.
Safety Approvals
U.S.A.
Australia*
Canada
Europe
RF Approvals
U.S.A.
Australia*
Canada
Europe
Singapore*
Ul Listed, C22.2 No. 950/UL 1950
conforms to AS/NZS
3548cUL Listed
TÜV Rheinland GS Licensed, EN 60950 (IEC
950) (Scanner and Base only - not on battery)
FCC Part 15.249 Certified
C-TIC
RSS 210 Certified
ETS 300 328 Certified
Type Approval for Spread Spectrum System
* Applies to SCANTEAM 2070 and 5770 only.
Cordless Quick Start Guide
Introduction
The Cordless Scanning System consists of the SCANTEAM 2070 Base unit and
at least one IMAGETEAM 3870 Cordless Linear Imager or SCANTEAM 5770
Cordless Laser Scanner. Up to nine scanners may be associated with one base.
Each cordless scanner has a removable, rechargeable battery pack and
provides real time decoding within a 50 foot (15 meter) to 100 foot (31 meter)
radius1 of the base unit.
The Cordless System is an economical, durable solution for a wide variety of
portable data collection applications. The Cordless System features:
• a tough, ergonomic thermoplastic housing for comfort and durability.
• recognition and decoding of the most popular, industry-standard bar code
symbologies.
• scanner coverage of up to 7854 square feet (730 square meters).
• a wide range of interfaces that are compatible with many POS, keyboard
wedge, and RS-232 terminals.
• visible and audible feedback for confirmation of a successful decode.
• rechargeable batteries designed to operate through a whole work day.
This Quick Start Guide contains information about charging your cordless
scanner’s battery pack and associating the scanner to the base. For more
detailed information on how to set up, operate, and program the cordless system,
see the Cordless System Manual.
This guide contains the following information:
• Battery pack and charging Information
• Associating the cordless scanner to a base
• Customer support information
• Limited warranty and warranty durations
1. Actual radio range depends on environment.
1
About the Battery Pack
Power is supplied to the Cordless Scanner by a
rechargeable battery pack that snaps onto the
bottom of the scanner. Each scanner is shipped
with a battery pack.* (See the battery specifications
in the Cordless System Manual for storage
information.)
*Order backup battery pack(s) or replacement
batteries from your distributor.
North American Charging Information
The battery pack is designed to plug into any two
prong North American AC power outlet (110/120 V)
for direct charging. You need no additional equipment and you can recharge the
pack virtually anywhere.
Worldwide Charging Information
Since the battery pack is rated for 110/120 V 60 Hz and 230/240 V 50 Hz
applications, it may be charged worldwide. To accommodate the wide variety of
electrical outlets internationally, a custom charge strip is required to charge the
batteries.
Warning: When the charge strip is used in 240 V applications, only use battery
CLESS/NIMH/S. Do not attempt to charge battery part numbers: 34/5770/
NICAD, 34/5770/NIMH, 34/5770/NIMH/F, or 34/5770/NICAD/F.
Battery Pack Recommendations
• Batteries are shipped uncharged and need to be fully charged and
discharged two or more times to be fully conditioned.
• Charge the battery for 24 hours for at least the first two times to fully
condition the battery. (Fully discharge in between each initial charge.)
• Charge the battery pack immediately before use or at least within a couple
of days of use.
• Remove the battery pack from the power outlet or charging strip within 24
hours after charging is completed. Avoid extended overcharging; do not
leave the battery charging for more than two days.
• Periodically fully discharge the battery pack.
• Avoid using the battery pack in extreme temperatures.
• Do not disassemble the battery pack. There are no user-serviceable parts
in the battery pack.
2
Proper Disposal of the Battery Pack
When the battery pack has reached the end of its useful life,
the batteries should be disposed of by a qualified recycler or
hazardous materials handler. Do not incinerate the battery
pack or dispose of the battery pack with general waste
materials. Contact the Product Service Department (see page
5) for recycling or disposal information.
Charging Your Battery Pack
Charge the battery pack by following the steps below:
1. Fully charge the battery (see page
2). Plug the battery pack directly
into any common 120 V AC outlet
in North America. If outside North
America, use the custom charge
strip.
2. The LED on the bottom of the battery pack lights red when the unit is
charging; it shows green when it is
fully charged and ready to use.
Note: It is important that you charge
the battery for 24 hours prior to
first use. No damage occurs if
this is not done, but the battery
capacity will not be at 100%.
(Fully discharge in between
each initial charge.)
Recharge Time: 6 hours at any
voltage at 20°C (68°F.)
3. After the battery pack is fully
charged, attach it to the cordless
scanner by pressing the pack firmly (align the prongs on the pack with the
mating receptacles) in the base of the scanner until the release buttons click,
holding the pack firmly in place. (When you attach a charged battery pack to
the Cordless Scanner, you will hear a single beep.)
4. If you have not set up your Cordless System, refer to “Setting Up and Connecting the Cordless System” section in the System Manual for instructions.
When the battery pack needs recharging, the yellow LED on top of the scanner
gives 3 short pulses. You will still be able to use the scanner; however eventually
the LED will flash 3 times and the scanner will not scan. If the LED stops flashing
when the temperature lowers or you do not use the battery pack for some time,
you still need to charge the battery pack to avoid damaging the battery pack or
causing scanner memory loss.
3
Associating the Cordless Scanner to a Base
Important:Make sure the cordless scanner’s battery pack has been fully
charged. See page 2 for charging instructions.
Using the cordless scanner, scan the Association Bar Code (the bar code label
on the top of the base) to link that scanner to the base.
Two quick beeps followed by clicking, then a single beep indicates a “good”
association. The scanner is in communication with the base.
If the battery pack is removed from the scanner and replaced after association,
the scanner automatically reassociates to the base if the base has power. In this
case, the scanner beeps when a charged battery pack is installed, then beeps a
second time after full association, usually five to ten seconds later.
Note: To set up and connect the cordless system to the host system, refer to the
Cordless System Manual. The System Manual includes all programming
selections, more detailed explanations of the cordless system, product
specifications, scan maps, connector illustrations and pinouts,
maintenance, and troubleshooting information.
Obtaining Factory Service
Hand Held Products provides service for all its products through a service center
located at its manufacturing facilities in Skaneateles, New York. To obtain warranty
or non-warranty service, return the unit to Hand Held Products (postage paid) with a
copy of the dated purchase record attached.
In the United States, please contact the Hand Held Products’ Product Service
Department at the address/telephone number that follow to obtain a Return Material
Authorization number (RMA #).
4
Main Office - Welch Allyn Data Collection, Inc. (d/b/a Hand Held Products)
4619 Jordan Road
P.O. Box 187
Skaneateles Falls, New York 13153-0187
Product Service Department
Telephone: (315) 685-4278 or 685-4360 Fax: (315) 685-4156
For service in Europe, please contact your Hand Held Products’ representative (at the
address that follows) or your local distributor.
European Office - Hand Held Products, Ltd.
Hondsruglaan 87 D
5628 DB Eindhoven
The Netherlands
Telephone: Int+ 31 40 242 4486 Fax:
Int+ 31 40 242 5672
United Kingdom Office - Hand Held Products, (UK) Ltd.
Dallam Court
Dallam Lane
Warrington
Cheshire WA2 7LT
United Kingdom
Telephone:Int+44 (0) 1 925 240055or Int+353 1 216 0070
Fax:
Int+44 (0) 1 925 631280or Int+353 1 295 6353
For service in Asia, please contact your Hand Held Products’ representative (at the
address that follows) or your local distributor.
Asia/Pacific Office - Hand Held Products
10/F Tung Sun Commercial Centre
194-200 Lockhart Road
Wanchai, Hong Kong
Telephone: Int+852-2511-3050 or 2511-3132 Fax: Int+852-251-1355
For service in Japan, please contact your Hand Held Products’ representative (at the
address that follows) or your local distributor.
Japan Office - Hand Held Products
Bon Marusan 8F
3-5-1 Kanda-Jinbocho
Chiyoda-ku
Tokyo 101, Japan
Telephone: Int+81-3-5212-7392
Fax: Int+81-3-3261-7372
For service in Latin America, please contact your Hand Held Products’ representative
(at the address that follows) or your local distributor.
Latin America Office - Hand Held Products
5150 North Tamiami Trail
Suite 302
Naples, FL 34103-2821
Telephone: (941) 263-7600 Fax: (941) 263-9689
5
Help Desk
If you need assistance installing or troubleshooting your cordless system, please
contact your distributor or the nearest Hand Held Products’ technical support office.
North America:
Telephone:
(315) 685-2476 (8 a.m. to 6 p.m. EST)
Fax number:
(315) 685-4960
E-mail:
dcd_techsupt@mail.welchallyn.com
Europe:
Telephone:
European Ofc: Int+31 40 242 4486)
U.K. Ofc:
Int+44 1925 240055
E-mail:
dcd_techsupt@mail.welchallyn.com
Asia:
Telephone:
Int+852-2511-3050 or 2511-3132
E-mail:
dcd_techsupt@mail.welchallyn.com
Limited Warranty
Welch Allyn Data Collection, Inc. (d/b/a Welch Allyn Data Collection, Inc.), hereby warrants
its products to be functional and free from manufacturing defects at the time of delivery.
Hand Held Products further warrants that it will replace or repair, at its option, any unit that
fails to perform according to Hand Held Products’ published specifications during a
specified duration (see chart below) from the time of shipment by Hand Held Products to
the user at the time it is purchased from any of Hand Held Products’ Authorized
Distributors. Any attempt on the part of the user to disassemble or service the equipment
shall void the warranty.
The warranty does not apply to product which have been damaged by improper handling,
shipping, or misuse. The warranty does not apply, if, in the sole opinion of Hand Held
Products, the unit has been damaged by accident, misuse, neglect, improper shipping and
handling. Since the unit is sensitive to static, the responsibility to protect it from static
damage is solely that of the user. The warranty is valid only if the unit or scanner has not
been tampered with or serviced by any party unauthorized by Hand Held Products as a
repair facility.
THE WARRANTIES SET FORTH HEREIN ARE IN LIEU OF ANY AND ALL OTHER
WARRANTIES EXPRESSED OR IMPLIED INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE BUYER
ACKNOWLEDGES THAT NO OTHER REPRESENTATIONS WERE MADE OR RELIED
UPON WITH RESPECT TO THE QUALITY AND FUNCTION OF THE CORDLESS
SYSTEM HEREIN SOLD.
In no event shall Hand Held Products or its resellers be liable for any loss, inconvenience
or damage whether direct, incidental, consequential or otherwise, and whether caused by
negligence or other fault resulting from the breach of any express warranty except as set
forth herein. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary
from state to state or country to country.
Limited Warranty Durations
6
IMAGETEAM
3870
SCANTEAM
5770
SCANTEAM
2070
NIMH
Battery
3 Years
3 Years
3 Years
1 Year
Statement of Agency Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
FCC Class B Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio or television technician for help.
Caution: Any changes or modifications made to this device that are not expressly
approved by Hand Held Products may void the user’s authority to operate the
equipment.
Note: To maintain compliance with FCC Rules and Regulations, cables connected to
this device must be shielded cables, in which the cable shield wire(s) have
been grounded (tied) to the connector shell.
Canadian Notice
This equipment does not exceed the Class B limits for radio noise emissions as
described in the Radio Interference Regulations of the Canadian Department of
Communications.
Le present appareil numerique n’emet pas de bruits radioelectriques depassant les
limites applicables aux appareils numeriques de la classe B prescrites dans le
Reglement sur le brouillage radioelectrique edicte par le ministere des
Communications du Canada.
CDRH Laser Safety Statement - ST5770 only
This product complies with US DHHS 21 CFR J Part 1040.10. This product is a
CLASS II LASER PRODUCT with a maximum output of 1.0 mW at 670 nanometers
and continuous wave.
EN 60825-1 Laser Safety Statement - ST5770 only
This product is classified as a CLASS 2 LASER PRODUCT with a maximum
output of 9.0 mW at 670 nanometers per EN 60825-1:1994, Issue 2, June 1997.
7
Enlarged Views of Regulatory Labels
Manufactured
MAY 2000
Model # IMAGETEAM 3870
Item # 3870XX-XX
S / N 12345
REV SW 1.6/1.08
Welch Allyn, Skaneateles Falls
New York 13153-0187, USA
See User Guide for Patent Information
Made in USA
Cordless Scanner
Left Side View
Cordless Scanner
Right Side View
Complies with (en conformite avec):
FCC PART 15
CANADA ICES-003
See manual
(Reféréz-vous à la documentation)
CISPR 22 CLASS B
Contains TX FCC ID: EHAUL
ISC: RSS/CNR 210
CANADA: 31101021090A
8
Sample Symbols
UPC A
0 123456 7890
Interleaved 2 of 5
1234567890
Code 128
Code 128
EAN 13
9 780330 290951
Code 93
123456-9$
MicroPDF417
Test Message
Code 39
BC321
Codabar
A13579B
PDF417
Vehicle Registration
4619 Jordan Road
P.O. Box 187
Skaneateles Falls, New York 13153-0187
38/5770/QS Rev A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising