Daikin | FH45BZV1 | Specifications | Daikin FH45BZV1 Specifications

Daikin FH45BZV1 Specifications
ESIE02–01
4
Part 4
Commissioning and Test
Run
3
What is in this part?
This part contains the following chapters:
Chapter
See page
1–Pre-Test Run Checks
4–3
2–Field settings
4–9
3–Test Run and Operation Data
4–27
44
5
Part 4 – Commissioning and Test Run
4–1
ESIE02–01
1
3
4
5
4–2
Part 4 – Commissioning and Test Run
ESIE02–01
Pre-Test Run Checks
Part 4
1
1
Pre-Test Run Checks
1.1
What Is in This Chapter?
Introduction
Overview
This chapter contains the following information:
■
Checks before test run
■
Test run checks
■
Setting the address for the receiver of the infrared remote control
■
Setting the address for the infrared remote control.
3
4
This chapter contains the following topics:
Topic
See page
1.2–Test Run Checks
4–4
1.3–Setting the Infrared Remote Control
4–5
5
Part 4 – Commissioning and Test Run
4–3
Pre-Test Run Checks
1
1.2
ESIE02–01
Test Run Checks
Checks before test
run
Before carrying out a test run, proceed as follows:
Step
Action
1
Make sure the voltage at the primary side of the safety breaker is:
2
3
Test run checks
4
5
4–4
■
230 V ± 10% for 1-phase units
■
400V ± 10% for 3-phase units.
Fully open the liquid and the gas stop valve.
To carry out a test run, check the following:
■
Check that the temperature setting of the remote control is at the lowest level or test mode.
■
Switch ON the indoor units one by one to check whether they operate correctly. Afterwards, switch
ON all units to check whether they all operate simultaneously.
■
Go through the following checklist:
Checkpoints
Cautions or warnings
Are all units securely installed?
■
Dangerous for turning over during
storm.
■
Possible damage to pipe
connections.
Is the earth wire installed according to the applicable
local standard?
Dangerous if electric leakage occurs.
Are all air inlets and outlets of the indoor and outdoor
units unobstructed?
■
Poor cooling.
■
Poor heating.
Does the drain flow out smoothly?
Water leakage.
Is piping adequately heat-insulated?
Water leakage.
Have the connections been checked for gas leakage?
■
Poor cooling.
■
Poor heating.
■
Stop.
Is the supply voltage conform to the specifications on
the name plate?
Incorrect operation.
Are the cable sizes as specified?
Damage of cables.
Are the remote control signals received by the unit?
No operation.
Part 4 – Commissioning and Test Run
ESIE02–01
1.3
Pre-Test Run Checks
Setting the Infrared Remote Control
Introduction
Setting the address
for the receiver
1
To set the infrared remote control, you have to set the address for:
■
The receiver of the infrared remote control
■
The infrared remote control.
The address for the receiver of the infrared remote control is factory set to 1. To change this setting,
proceed as follows:
Step
Action
1
Turn OFF the power.
2
Remove the sealing pad on the top of the receiver.
3
Sealing pad
M
Small opening
S
SS
3
1
2
SS
1
2
4
Receiver
3
Set the wireless address switch (SS2) according to the table below. You can find the wireless address switch attached on the PCB of the receiver and it is visible through the small
opening on the back of the receiver.
No. 1
No. 2
No. 3
Unit No.
1 2 3
1 2 3
4
1 2 3
SS2
If you use a wired and an infrared remote control for one indoor unit, proceed as follows:
1. Set the wired remote control to MAIN: On the remote control.
2. Set the infrared remote control to SUB: On the receiver with the MAIN/SUB switch
(SS1).
MAIN
SUB
MAIN/SUB
SS1
5
S
M
S
M
Seal off the opening of the address switch and the MAIN/SUB switch with the attached
sealing pad.
Sealing pad
S
2
M
SS
3
1
Small opening
2
SS
1
Receiver
6
Make sure to also change the address on the remote control.
Part 4 – Commissioning and Test Run
4–5
5
Pre-Test Run Checks
1
Setting the address
for the infrared
remote control
ESIE02–01
The address for the infrared remote control is factory set to 1. To change this setting, proceed as
follows:
Step
Action
1
Hold down the FILTER RESET button and the TEST button for at least 4 s, to go to field
set mode. The display indicates the field set mode.
3
4
FILTER RESET
TEST
5
2
Press the FAN button to select a multiple setting (A/b), see ‘Multiple settings A/b’ further
in this section. Each time you press the button, the display switches between “A” and “b”.
FAN
4–6
Part 4 – Commissioning and Test Run
ESIE02–01
Pre-Test Run Checks
Step
Action
3
Press the UP and DOWN buttons to set the address. Set the same address as the
receiver (1, 2 or 3). The receiver does not work with addresses 4, 5 and 6.
1
UP
DOWN
3
4
4
Press the RESERVE button to confirm the setting.
5
RESERVE
Part 4 – Commissioning and Test Run
4–7
Pre-Test Run Checks
1
ESIE02–01
Step
Action
5
Press the TEST button to quit the field set mode and return to the normal display.
ON / OFF
TEMP
TIME
˚C
UP
DOWN
FAN
RESERVE CANCEL
TIMER
3
MODE
SWING
/TEST
TEST
4
5
Multiple settings
A/b
When an outside control (central remote control...) controls an indoor unit, sometimes the indoor unit
does not respond to ON/OFF and temperature settings commands from this remote control.
Remote control
4–8
Indoor unit
Setting
Remote control display
Control of other air conditioners and units
A: Standard
All items are displayed.
Commands other than ON/OFF
and temperature setting
accepted. (1 long beep or
3 short beeps emitted)
b: Multi System
Only one item is displayed. This item is
only shown for a few
seconds.
All commands accepted (2 short beeps)
No other control
Part 4 – Commissioning and Test Run
ESIE02–01
Field settings
Part 4
1
2
Field settings
2.1
What Is in This Chapter?
Introduction
Overview
This chapter contains the following information:
■
How to change the field settings
■
The field settings
■
The factory settings.
3
This chapter contains the following topics:
Topic
See page
2.2–How to Change the Field Settings with the Wired Remote Control
4–10
2.3–How to Change the Field Settings with the Infrared Remote Control
4–12
2.4–Overview of the Field Settings of the Indoor Units
4–13
2.5–Overview of the Factory Settings of the Indoor Units
4–14
2.6–Setting the Ceiling Height
4–15
2.7–Setting the Filter Counter
4–16
2.8–MAIN/SUB Setting when Using Two Remote Controls
4–17
2.9–Setting the Centralized Group No.
4–18
2.10–The Field Setting Levels
4–19
2.11–Overview of the Field Settings: R(Y)P71-250B
4–22
2.12–Jumpers
4–23
2.13–DIP switch DS1
4–24
2.14–DIP switch DS2
4–25
Part 4 – Commissioning and Test Run
4
5
4–9
Field settings
1
2.2
ESIE02–01
How to Change the Field Settings with the Wired Remote Control
Installation
conditions
The field settings have to be changed with the remote control according to the installation conditions.
Wired remote
control
The illustration below shows the wired remote control.
5 12
4
2
1
3
3
7
hr
C
hr
6
8
NOT
AVAILABLE
TEST
9
11
10
13
L H
14
4
21
20
TEST
5
16
Components
4–10
19
15
17
18
22
The table below contains the components of the wired remote control.
No.
Component
No.
Component
1
ON/OFF button
12
Display
2
Operation lamp (red)
13
3
Display
Under centralized control
14
Timer mode start/stop button
4
Ventilation/air cleaning
15
Timer ON/OFF button
5
Operating mode
16
Inspection/test operation button
6
Inspection/test operation
17
Programming time button
7
Programmed time
18
Temperature setting button
8
Set temperature
19
Filter counter reset button
9
Fan speed
20
Fan speed control button
10
Air flow flap
21
Operating mode selector button
11
Time to clean air filter
22
Air flow direction adjust button
Defrost
Non-functioning
Part 4 – Commissioning and Test Run
ESIE02–01
Setting
Field settings
1
To set the field settings, you have to change:
■
“Mode No.”
■
“First code No.”
■
“Second code No.”.
To change the field settings, proceed as follows:
Step
Action
1
Hold down the INSPECTION/TEST button for at least 4 s during normal mode to enter
the “Field setting mode”.
2
Press the TEMPERATURE CONTROL button until the desired “Mode No.” appears.
3
■
If the indoor unit is under group control, all settings for all the indoor units are set at the
same time. Use the codes 10 to 15 to apply this group control and proceed to the next
step.
■
If you want to set the indoor units of one group individually or if you want to read out
the last settings, use the codes 20 to 25 which are displayed in brackets. Press the
TIMER SELECTION button to select the “Indoor unit No.” for which you want to adjust
the field settings.
4
Press the upper part of the PROGRAMMING TIME button to select the “First code No.”.
5
Press the lower part of the PROGRAMMING TIME button to select the
“Second code No”.
6
Press the CONFIRMATION button to confirm the changed setting.
7
Press the INSPECTION/TEST button to return to “Normal mode”.
Part 4 – Commissioning and Test Run
3
4
5
4–11
Field settings
1
2.3
ESIE02–01
How to Change the Field Settings with the Infrared Remote Control
Optional
accessories
If optional accessories are mounted on the indoor unit, the indoor unit setting may have to be changed.
Refer to OH98-2 or the installation manual (optional handbook) for each optional accessory.
Infrared remote
control
The illustration below shows the infrared remote control.
UP button
Mode No.
3
DOWN button
Field setting mode
RESERVE button
First code No.
4
MODE button
Second code No.
INSPECTION/TEST button
5
Setting
To set the field settings, you have to change:
■
“Mode No.”
■
“First code No.”
■
“Second code No.”.
To change the field settings, proceed as follows:
4–12
Step
Action
1
Hold down the INSPECTION/TEST button for at least 4 s during normal mode to enter
the “Field setting mode”.
2
Press the MODE button to select the desired “Mode No.”.
3
Press the UP button to select the “First code No.”.
4
Press the DOWN button to select the “Second code No.”
5
Press the RESERVE button to set the present settings.
6
Press the INSPECTION/TEST button to return to the “Normal mode”.
Part 4 – Commissioning and Test Run
ESIE02–01
2.4
Field settings
Overview of the Field Settings of the Indoor Units
Field settings
Mode
No.
10 or 20
1
The table below contains the possible field settings of all indoor units.
First
code
No.
Second code No.
Description of the setting
01
02
03
04
0
Filter counter
Long
Short
—
—
1
Filter type
Long
Super long
External
Oil mist
2
Remote thermistor of the
remote control
TH1 = rem.
control
TH1 = air
return
—
—
3
Filter display
Filter indic.
No filter indic.
—
—
9
Centralized control
Yes
No
—
—
0
Number indoor to 1 outdoor
Pair
Twin
Triple
Double twin
1
Unified or indiv. set twin
Group setting
Indiv. setting
—
—
2
Fan OFF at thermostat OFF
LL-speed
OFF
—
—
0
KRP1B51/52/53 X1/X2 output
Thermostat
ON
Option
Operation
Malfunction
3
Fan speed heating thermostat
OFF
LL-speed
Set speed
—
—
5
Automatic restart
Disabled
Enabled
—
—
0
Ceiling height setting
Normal
High
Extra high
—
1
4-, 3- or 2-way air outlet
4-way
3-way
2-way
—
3
Horizontal discharge grill
Enabled
Disabled
—
—
4
Air flow direction adjust range
setting
Draft prevention
Standard
Ceil soil prevention
—
5
Field fan speed changeover
air outlet
Standard
Option 1
Option 2
—
6
External static pressure
Normal
High
Low
—
14 or 24
0
Additional timer to guard timer
0s
5s
10 s
15 s
15 or 25
1
Humidifier during thermostat
OFF
No
Yes
—
—
3
Drain pump during humidifying (heating)
No
Yes
—
—
5
Ventilation unit indiv. setting
No
Yes
—
—
6
Air-cleaner unit indiv. setting
No
Yes
—
—
11 or 21
12 or 22
13 or 23
Part 4 – Commissioning and Test Run
3
4
5
4–13
Field settings
1
2.5
ESIE02–01
Overview of the Factory Settings of the Indoor Units
Factory settings
Mode No.
10 or 20
First code
No.
Second code No.
FHYCP
FHYKP
FHYBP
FAYP
FDYP
FUYP
FHYP
0
01
01
01
01
01
01
01
1
01
—
—
—
02
01
—
2
02
—
—
—
02
02
—
3
01
01
01
01
01
01
01
9
—
—
—
—
01
—
—
0
01
01
01
01
01
01
01
1
01
01
01
01
01
01
01
2
01
01
01
01
01
01
01
0
01
01
01
01
01
01
01
3
01
—
01
—
—
—
—
5
02
02
02
02
02
02
02
0
01
—
—
01
—
01
01
1
01
—
—
—
—
—
—
3
—
01
—
—
—
—
—
4
02
02
—
—
—
—
—
5
01
—
—
01
—
01
01
6
—
01
01
—
—
—
—
14 or 24
0
01
01
01
—
01
01
01
15 or 25
1
—
—
—
—
01
—
—
3
—
—
—
—
01
—
—
5
01
01
01
01
—
01
01
6
01
01
01
01
—
01
01
3
11 or 21
4
The table below contains the factory settings of all indoor units
12 or 22
13 or 23
5
4–14
Part 4 – Commissioning and Test Run
ESIE02–01
2.6
Field settings
Setting the Ceiling Height
Incorrectly setting
1
If you set the remote control incorrectly, a connection mistake malfunction “UA” will appear on the
remote control display.
See ’Malfunctioning Field Setting Switch (UA)’ on page 3–62.
Mode No. 13 or 23
First code No. 0
Set the second code No., according to the tables below.
FHYP
Second code No.
Ceiling-suspended type
01
Height < 2.7 m
02
2.7 m < height < 3.5 m
03
Not used
3
FAYP
Second code No.
Wall-mounted type
01
Normal
02
High
03
Extra high
4
5
FHYCP and FUYP
Indoor unit
Second code No.
4-way outlet
3-way outlet
2-way outlet
FHYCP35-71
01
< 2.7 m
< 3.0 m
< 3.5 m
02
< 3.0 m
< 3.3 m
< 3.8 m
03
< 3.5 m
< 3.5 m
—
01
< 3.2 m
< 3.6 m
< 4.2 m
02
< 3.6 m
< 4.0 m
< 4.2 m
03
< 4.2 m
< 4.2 m
—
01
< 2.7 m
< 3.0 m
< 3.5 m
02
< 3.0 m
< 3.5 m
< 3.8 m
03
< 3.5 m
< 3.8 m
—
FHYCP100-125
FUYP
Part 4 – Commissioning and Test Run
4–15
Field settings
1
2.7
ESIE02–01
Setting the Filter Counter
Mode No. 10 or 20
First code No. 0
When the filter counter indication time is set to ON, set the second code No., according to the table
below
Filter specifications
Second code No.
Long life
Standard
Ultra long life
01
Light contamination
2 500 h
200 h
10 000 h
02
Heavy contamination
1 100 h
100 h
5 000 h
When there is a heavy contamination and a long life filter is installed, the setting hours for the units
FHYCP and FHYP are 1 250 h.
3
Fan speed OFF
when
thermostat OFF
4
When the cool/heat thermostat is OFF, you can stop the indoor unit fan by switching the setting to
“Fan OFF”. This setting is used as a countermeasure against odour, for example for barber shops and
restaurants.
Mode No.
11 or 21
5
Contamination
Fan speed
changeover when
thermostat OFF
12 or 22
Setting
01
—
02
Fan OFF
2
First code No.
Second code No.
Setting
01
LL fan speed
02
Set fan speed
3
Set the air flow direction of the indoor units as given in the table below. This setting is needed when
the optional air outlet blocking pad has been installed. The “Second code No” is factory set to “01”.
Mode No
13 or 23
4–16
Second code No.
You can switch the fan speed to the set fan speed when the heating thermostat is OFF. This setting is
called “Set Fan Speed”.
Mode No.
Air flow direction
setting
First code No.
First code No
1
Second code No
Setting
01
F: four-direction air flow
02
T: three-direction air flow
03
W: two direction air flow
Part 4 – Commissioning and Test Run
ESIE02–01
2.8
Field settings
MAIN/SUB Setting when Using Two Remote Controls
1
Situation
The MAIN/SUB setting is necessary when one indoor unit is controlled by two remote controls. When
you use two remote controls (control panel and separate remote control), set one to MAIN and the
other to SUB. You can do this by setting the switch on the remote control’s PCB.
Setting
The remote controls are factory set to MAIN, so you only have to change one remote control from
MAIN to SUB. To change a remote control from MAIN to SUB, proceed as follows:
Step
Action
1
Insert a flathead screwdriver into the recess between the upper and lower part of the
remote control, as shown in the illustration below. Gently pry off the upper part of the
remote control, working from the two possible positions.
3
Upper part of the
remote control
4
Lower part of the
remote control
2
Turn the MAIN/SUB changeover switch on the PCB to “S”.
M
S
M
S
Part 4 – Commissioning and Test Run
5
The switch is set to
MAIN (factory setting)
Set the switch to SUB.
4–17
Field settings
1
2.9
ESIE02–01
Setting the Centralized Group No.
When?
If you want to carry out centralized control with a central remote control and a unified ON/OFF control,
you have to set the group No. for each group with the remote control.
Wired remote
control
The illustration below shows the wired remote control.
Mode No.
Initial setting mode
3
Group No.
4
Setting
5
To set the “Centralized group No.”, proceed as follows:
Step
Action
1
Switch ON the power supply of the central remote control, the unified ON/OFF control
and the indoor unit(s).
2
Hold down the INSPECTION/TEST button for at least 4 s during normal mode to enter
the “Field setting mode”.
3
Press the TEMPERATURE CONTROL button until “Mode No.” “00” appears.
4
Press the INSPECTION/TEST button to inspect the group No. display.
5
Set the “Group No.” for each group by pressing the PROGRAMMING TIME button.
The “Group No.” rises in the order of 1—00, 1—01, ..., 1—15, 2—00, ..., 2—15, 3—00,
etc. The unified ON/OFF control however displays only the range of group numbers
selected by the switch for setting each address.
Individually
address setting
4–18
6
Press the CONFIRMATION button to enter the selected group No.
7
Press the INSPECTION/TEST button to return to normal mode.
If the address must be set individually for each unit, set the “Mode No.” to “30”. For example, for power
consumption counting.
Part 4 – Commissioning and Test Run
ESIE02–01
2.10
Field settings
The Field Setting Levels
Introduction
The inspection level
1
The three field setting levels are:
■
Inspection level
■
Monitoring level
■
Maintenance mode settings.
The inspection level is the highest level of the three field setting levels. You can change the views in
the inspection level by pressing the INSPECTION/TEST button.
The flow chart below explains the different windows of the inspection level.
3
Normal display
Push INSPECTION/TEST button
Last occurred
malfunction
4
Push INSPECTION/TEST button
Push
INSPECTION/TEST
button
Indoor model and
size
See possible
system settings.
5
Push INSPECTION/TEST button
System
Push INSPECTION/TEST button
Test
Part 4 – Commissioning and Test Run
4–19
Field settings
1
Possible system
settings
ESIE02–01
The table below contains the possible system settings, which are displayed on the remote control if
the TEST button is pushed twice shortly.
Size
Type
Software
Settings
Display
Settings
Display
35
35
FHYCP
FC
45
45
FHYP
HC
60
63
FAYP
AC
71
71
FHYKP
EC
5
3
4
Changing the mode
settings
5
4–20
100
100
FHYBP
JC
125
125
FUYP
3C
200
200
FDYP
UC
250
250
—
To enter the monitoring level and to change the maintenance mode settings, proceed as follows:
Step
Action
1
Hold down the INSPECTION/TEST button for at least 4 s to enter the field setting mode.
2
Hold down the INSPECTION/TEST button for at least 4 s to enter the maintenance mode.
3
Press the TEMPERATURE CONTROL buttons as many times as needed to select the
mode No. you want.
4
Press the TIMER SELECTION button as many times as needed to select the unit No. you
want.
5
Carry out the settings for modes 44 and 45. See “Maintenance Mode Settings” further in
this section.
6
Press the CONFIRMATION button to confirm the settings of modes 44 and 45.
7
Press the INSPECTION/TEST button to return to the normal operating mode.
Part 4 – Commissioning and Test Run
ESIE02–01
Field settings
Mode No.
1
The table below describes the maintenance mode settings.
Function
Content and operation method
Example of the remote control display
Display malfunction history
40
History error
codes
The history No. can be changed with the programming time button.
Past error code
Unit No.
CODE
SETTING
0: Newest
Malfunction
history
-
Maintenance Mode
Settings
2: Oldest
* “00” displayed for 3 and subsequent
Select the display thermistor with the programming time button.
41
43
Thermistor
data display
Forced fan ON
Thermistor:
0. Remote control thermistor
1. Suction thermistor
2. Heat exchanger thermistor.
Turns the fan ON for each unit individually.
Thermistor
3
Temperature
Unit No.
SETTING
4
Unit No.
SETTING
Sets fan speed and air flow direction for each
unit individually when using group control.
44
Individual
setting
Settings are made using the “air flow direction adjust” and “fan speed adjust” buttons.
Confirmation by the confirmation button is
required.
Fan
speed
Unit No.
change
Set the unit No. after changing with the programming time buttons.
Confirmation by the confirmation button is
required.
CODE
SETTING
Field set No
No after change
Unit No.
CODE
Part 4 – Commissioning and Test Run
5
Air flow direction
Unit No.
Changes unit No.
45
1: Low
3: High
SETTING
4–21
Field settings
1
2.11
Overview of the Field Settings: R(Y)P71-250B
Jumpers
The table below contains the jumper field settings.
Jumper
Label on PCB
Function
Applicable units
J1
Thermo CTR
Change thermostat OFF control indoor unit
■
RP71-250B
4–23
J3
Thermo CTR2
Change thermostat ON control indoor unit
■
RYP71-250B
4–23
DIP switches
3
4
ESIE02–01
See page
The table below contains the DIP switch field settings.
DIP
switch
Label on PCB
Function
Applicable units
Details
DS1-1
E.V. open during defrost
Increase E.V. opening degree during
defrost
RYP71-250B
4–24
DS1-2
Defrost starting condition
Increase possibility to start defrost
DS2-1
Defrost starting time
Change defrost interval
DS2-2
Mode B
Reduce E.V. opening degree during defrost
DS2-3
Freeze 1
Disable intelligent function
■
RP71-250B
4–26
DS2-4
Freeze 2
Increase possibility to start freeze-up
■
RYP71-250B
4–26
DS3-1
Emergency ON/OFF
Switch emergency operation outdoor unit
ON
■
RP71-250B
—
■
RYP71-250B
Select emergency cooling / heating operation on outdoor unit
RYP71-250B
—
Details
5
DS3-2
Cool / Heat
BS
4–24
RYP71-250B
4–25
4–25
The table below contains the BS field setting.
BS
Label on PCB
Function
Applicable units
BS
Pump down / forced
defrost
Cooling/fan only: Pump down (see further
in this section)
■
RP71-250B
■
RYP71-250B
—
Heating: Forced defrosting
Pump down
Pump down is preferably carried out with the indoor unit set to “fan only” in order to avoid compressor
restart with closed stop valves after finishing the previous pump down operation (close stop valves,
turn OFF the power supply).
If accidentally, the power was switched back ON, the unit will automatically restart with closed stop
valves, which may result in a possible compressor breakdown.
4–22
Part 4 – Commissioning and Test Run
ESIE02–01
2.12
Field settings
Jumpers
Input and output
1
The table below describes the input and the output of the jumpers.
Item
Description
Input
∆Tr
Output
J1
Cooling
∆Tr = Tr - Ts
■
Tr = indoor unit suction air temp.
Heating
∆Tr = Ts - Tr
■
Ts = temp. set by the remote control
Magnetic switch compressor K1M
The function of jumper J1 is to reduce the possibility of thermostat OFF (reduce ON/OFF cycle compr.).
Field setting (open state)
Thermostat goes into OFF-state when
Thermostat goes into OFF-state when
∆Tr ≤ 0.0˚C
■
-0.5˚C < ∆Tr ≤ 0.0˚C for 3 min, or
■
-1.5˚C < ∆Tr ≤ -0.5˚C for 1 min, or
■
∆Tr ≤ -1.5˚C
Input: ∆Tr
Input: ∆Tr
∆Tr
4
∆Tr ≤ 0.0˚C and ≥ 3 min
∆Tr ≤ -0.5˚C and ≥ 1 min
∆Tr
+1.0
+1.0
0.0
-0.5
0.0
5
-1.5
Output: K1M
≥ 3 min
J3
3
Factory setting (closed state)
∆Tr ≤ -1.5˚C no delay
Output: K1M
ON
ON
OFF
OFF
≥ 3 min
The function of jumper J3 is to increase the differential for thermo ON.
Factory setting (closed state)
Field setting (open state)
Thermostat goes into ON-state when
Thermostat goes into ON-state when
∆Tr ≥ 1.0˚C
∆Tr ≥ 4.5˚C
Input: ∆Tr
Input: ∆Tr
∆Tr
+1.0
∆Tr
+4.5
0.0
0.0
Output: K1M
Pump down
Output: K1M
ON
ON
OFF
OFF
Part 4 – Commissioning and Test Run
Pump down
4–23
Field settings
1
2.13
ESIE02–01
DIP switch DS1
Priority
The table below contains the priority of the DIP switches.
When... are ON
3
DS1-1:
E.V. opening during
defrost
■
DS1-2
■
DS2-1
■
DS1-1
■
DS2-2
Then... has priority.
DS1-2
DS1-1
The table below describes the DIP switch.
Setting
Illustration
Function
Factory setting
OFF
At the start-up of the defrost operation, the E.V. will be opened to
the max. (480 pulses) for a limited time (1 or 2 min), before closing to 100 pulses.
1
2
4
Field setting
ON
1
2
5
The opening of the E.V. can change to the max. (480 pulses) in
order to increase the defrost capacity.
Mind the increased risk of liquid back.
DS1-2:
Defrost starting
condition
The table below describes the DIP switch.
Setting
Illustration
Function
Factory setting
OFF
For temperature settings at defrosting, see page 2–38.
1
Field setting
ON
1
4–24
2
2
Accumulated operation time for defrost activation = 3 h.
■
Increases the temp. conditions for defrost activation with 4˚C.
■
Changes the accumulated operation time from 3 h to 40 min
in order to advance the defrosting operation.
Part 4 – Commissioning and Test Run
ESIE02–01
2.14
Field settings
DIP switch DS2
Priority
1
The table below contains the priority of the DIP switches.
When... are ON
DS2-1:
Defrost starting
time
■
DS1-2
■
DS2-1
■
DS1-1
■
DS2-2
Then... has priority.
DS1-2
DS1-1
3
The table below describes the DIP switch.
Setting
Illustration
Factory setting
OFF
1
2
Function
3
4
Accumulated operation time for defrost operation
= 3 h.
4
Field setting
ON
1
DS2-2:
Mode B
2
3
4
Changes the accumulated operation time for the
defrost operation from 3 h to 24 h in order to delay
the defrosting operation.
The table below describes the DIP switch.
Setting
Illustration
Factory setting
OFF
1
Field setting
2
3
4
2
3
4
ON
1
Part 4 – Commissioning and Test Run
Function
At the start-up of the defrost operation, the E.V.
opens at the max. (480 pulses) for a limited time
(1 or 2 min), before closing to 100 pulses.
Changes the following in order to avoid liquid back
to the compressor:
■
Changes the limited time of E.V. opening at
max. (480 pulses) from 1 or 2 min to 30 s.
■
Stops the compressor at defrost start and stop.
4–25
5
Field settings
1
DS2-3:
Freeze 1
ESIE02–01
The table below describes the DIP switch.
Setting
Illustration
Factory setting
OFF
1
Field setting
Function
Enables the “intelligent” control function.
2
3
4
See page 2–28.
2
3
4
Disables the “intelligent” control function. It returns
to the freeze-up activation conditions similar as for
the G- and K-types.
ON
1
3
4
DS2-4:
Freeze 2
The table below describes the DIP switch.
Setting
Illustration
Factory setting
OFF
1
Function
Normal operation.
2
3
4
2
3
4
5
Field setting
ON
1
4–26
Enables the countermeasure to avoid ice/water
blow-out during freeze-up cycle.
Part 4 – Commissioning and Test Run
ESIE02–01
Test Run and Operation Data
Part 4
1
3
Test Run and Operation Data
Introduction
This chapter contains the following information:
■
General operation data
■
Operation ranges.
3
Overview
This chapter contains the following topics:
Topic
See page
3.1–General Operation Data
4–28
3.2–RP71B7V1, RP71B7W1, RP71B7T1, RP100B7V1, RP100B7W1, RP100B7T1,
RP125B7W1 and RP125B7T1
4–29
3.3–RP200B7W1 and RP250B7W1
4–30
3.4–RYP71B7V1, RYP71B7W1, RYP100B7V1, RYP100B7W1 and RYP125B7W1
4–31
3.5–RYP200B7W1 and RYP250B7W1
4–32
Part 4 – Commissioning and Test Run
4
5
4–27
Test Run and Operation Data
1
3.1
ESIE02–01
General Operation Data
During cooling
mode and dry keep
The operating conditions must be as follows:
Items
Operating modes
Outdoor temp.
■
c/o: -15 to +46˚CDB
■
A safety device may stop the operation.
■
h/p: -5 to +46˚CDB
■
Condensation may occur on the indoor unit and
start dripping.
Indoor temp.
+14 to +28˚CWB
Indoor humidity
80%
If the operation is out this range...
The operation values are guidelines in the operation range:
3
4
During heating
mode
■
LP: 3.0~6.5 barg (low pressure)
■
HP: 12.0~28.0 barg (high pressure)
■
Td: 60~95˚C (discharge pipe temperature compressor)
■
Ts: -2~15˚C (suction pipe temperature compressor)
■
∆Ti: 8~16˚C (indoor temperature difference  air return – air outlet ).
The operating conditions must be as follows:
5
Items
Operating modes
If the operation is out this range...
Outdoor temp.
-10 to +15.5˚CWB
A safety device may stop the operation.
Indoor temp.
+15 to +27˚CDB
The operation values are guidelines in the operation range:
4–28
■
LP: 1.8~6.4 barg (low pressure)
■
HP: 13.0~28.0 barg (high pressure)
■
Td: 55~95˚C (discharge pipe temperature compressor)
■
Ts: -15~10˚C (suction pipe temperature compressor)
■
∆Ti: 12~32˚C (indoor temperature difference  air return – air outlet ).
Part 4 – Commissioning and Test Run
ESIE02–01
3.2
Test Run and Operation Data
RP71B7V1, RP71B7W1, RP71B7T1, RP100B7V1, RP100B7W1,
RP100B7T1, RP125B7W1 and RP125B7T1
Conditions
Operation range
1
The illustration in this section is based on the following conditions:
■
Equivalent piping length: 7.5 m
■
Level difference: 0 m
■
Air flow rate: High.
The illustration below shows the operation range.
Outdoor temp.
(˚CDB)
3
46
44
Pull-down period
4
-15
14
5
25 28
Indoor temp.
(˚CWB)
Part 4 – Commissioning and Test Run
4–29
Test Run and Operation Data
1
3.3
ESIE02–01
RP200B7W1 and RP250B7W1
Conditions
Operation range
The illustration in this section is based on the following conditions:
■
Equivalent piping length: 70 m
■
Level difference: 30 m
■
Indoor air flow rate: 72 m³/min (200 class), 90 m³/min (250 class).
The illustration below shows the operation range.
Outdoor temp.
(˚CDB)
46
3
43
Pull-down period
4
5
-5
14
25 28
Indoor temp.
(˚CWB)
4–30
Part 4 – Commissioning and Test Run
ESIE02–01
3.4
Test Run and Operation Data
RYP71B7V1, RYP71B7W1, RYP100B7V1, RYP100B7W1
and RYP125B7W1
Conditions
Operation range:
Cooling
1
The illustrations in this section are based on the following conditions:
■
Equivalent piping length: 7.5 m
■
Level difference: 0 m
■
Air flow rate: High.
The illustration below shows the operation range.
Outdoor temp.
46
(˚CDB)
3
Pull-down period
44
4
5
-5
25 28
12
Indoor temp.
(˚CWB)
Operation range:
Heating
The illustration below shows the operation range.
Outdoor temp.
(˚CDB)
15
Warming-up period
10
5
-10
0
15
27
Indoor temp.
(˚CWB)
Part 4 – Commissioning and Test Run
4–31
Test Run and Operation Data
1
3.5
ESIE02–01
RYP200B7W1 and RYP250B7W1
Conditions
Operation range:
Cooling
The illustrations in this section are based on the following conditions:
■
Equivalent piping length: 70 m
■
Level difference: 30 m
■
Indoor air flow rate: 72 m³/min (200 class), 90 m³/min (250 class).
The illustration below shows the operation range.
Outdoor temp. 46
(˚CDB)
43
Pull-down period
3
4
5
-5
25 28
14
Indoor temp.
(˚CWB)
Operation range:
Heating
The illustration below shows the operation range.
Outdoor temp. 15
(˚CDB)
10
Warming-up period
5
-10
10
15
27
Indoor temp.
(˚CWB)
4–32
Part 4 – Commissioning and Test Run
ESIE02–01
4
Part 5
Disassembly and
Maintenance
3
What is in this part?
This part contains the following chapters:
Chapter
See page
1–Disassembly and Maintenance: Outdoor Units
5–3
2–Disassembly and Maintenance: Indoor Units
5–29
4
55
Part 5 – Disassembly and Maintenance
5–1
ESIE02–01
1
3
5
5–2
Part 5 – Disassembly and Maintenance
ESIE02–01
Disassembly and Maintenance: Outdoor Units
Part 5
1
1
Disassembly and Maintenance: Outdoor Units
1.1
What Is in This Chapter?
Introduction
Overview
This chapter contains the following information on the outdoor units:
■
Exploded views
■
Components.
3
This chapter contains the following topics:
Topic
See page
1.2–R35GZ7V11
5–4
1.3–R45GZ7V11 and R45GZ7W11
5–6
1.4–RY35EAZ7V1 and RY45EAZ7V1v
5–8
1.5–R60GZ7W11
5–10
1.6–MA56GZ7W11
5–12
1.7–MA90GZ7W11
5–14
1.8–RP71B7V1, RP71B7W1 and RP71B7T1
5–16
1.9–RYP71B7V1 and RYP71B7W1
5–18
1.10–RP100B7V1, RP100B7W1, RP100B7T1, RP125B7W1 and RP125B7T1
5–20
1.11–RYP100B7V1, RYP100B7W1 and RYP125B7W1
5–22
1.12–RP200B7W1 and RP250B7W1
5–24
1.13–RYP200B7W1 and RYP250B7W1
5–26
Part 5 – Disassembly and Maintenance
55
5–3
Disassembly and Maintenance: Outdoor Units
1
1.2
ESIE02–01
R35GZ7V11
The illustration below shows the exploded view.
Compressor
Exploded view
Stop valves
Capillary assy
3
Service port assy
55
5–4
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Outdoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
1
Front plate assy
27
Stop valve assy (liquid line)
1.1
DAIKIN name plate
27.1
Stop valve cover
1.2
R407C sticker
28
Flare nut
2
Right side plate
29
Stop valve assy (gas line)
3
Top plate
29.1
Stop valve cover
4
Discharge grille
29.2
Valve core
5
Suction grille
29.3
Blind cap
6
Bottom frame
30
Flare nut
7
Set plate for compressor
31
Service port assy
8
Service cover assy
31.1
Valve core
8.1
Wiring diagram sticker
31.2
Blind cap
9
Handle
32
Fan motor
10
Partition plate
33
Propeller fan
11
Fan motor stand
34
Fan nut
12
Compressor
35
Switch box assy
13
Compressor rubber
35.1
Switch box set plate
14
Nut
35.2
Magnetic contactor
15
Terminal cover
35.3
Magnetic switch
16
Terminal nut
35.4
Running capacitor
17
Terminal rubber
35.5
Capacitor (fan motor)
18
Compressor sound absorber 1
35.6
Thermostat
19
Compressor sound absorber 2
35.7
Surge absorber
20
Compressor sound absorber 3
35.8
Wire terminal
21
Compressor sound absorber top
35.9
Wire clamp
22
Sound absorber
35.10
Insulation strip
23
Outdoor heat exchanger assy
35.11
Noise filter assy
24
Bypass sealing plate
35.12
Capacitor fixing band
25
Cushion for heat exchanger assy
35.13
Reverse phase protector
26
Capillary tube assy
36
Overload protector
26.1
Capillary tube 1
37
Set plate for thermistor
26.2
Capillary tube 2
—
26.3
Capillary joint
26.4
Sound absorber putty
Part 5 – Disassembly and Maintenance
3
55
5–5
Disassembly and Maintenance: Outdoor Units
1
1.3
ESIE02–01
R45GZ7V11 and R45GZ7W11
The illustration below shows the exploded view.
Compressor
Exploded view
3
Service port assy
Stop valves
55
5–6
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Outdoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
1
Front plate assy
27
Stop valve assy (liquid line)
1.1
DAIKIN name plate
27.1
Stop valve cover
1.2
R407C sticker
28
Flare nut
2
Right side plate
29
Stop valve assy (gas line)
3
Top plate
29.1
Stop valve cover
4
Discharge grille
29.2
Valve core
5
Suction grille
29.3
Blind cap
6
Bottom frame
30
Flare nut
7
Set plate for compressor
31
Service port assy
8
Service cover assy
31.1
Valve core
8.1
Wiring diagram sticker
31.2
Blind cap
9
Handle
32
Fan motor
10
Partition plate
33
Propeller fan
11
Fan motor stand
34
Fan nut
12
Compressor
35
Switch box assy
13
Compressor rubber
35.1
Switch box set plate
14
Nut
35.2
Magnetic contactor
15
Terminal cover
35.3
Magnetic switch
16
Terminal nut
35.4
Running capacitor
17
Terminal rubber
35.5
Capacitor (fan motor)
18
Compressor sound absorber 1
35.6
Thermostat
19
Compressor sound absorber 2
35.7
Surge absorber
20
Compressor sound absorber 3
35.8
Wire terminal
21
Compressor sound absorber top
35.9
Wire clamp
22
Sound absorber
35.10
Insulation strip
23
Outdoor heat exchanger assy
35.11
Noise filter assy
24
Bypass sealing plate
35.12
Capacitor fixing band
25
Cushion for heat exchanger assy
35.13
Reverse phase protector
26
Capillary tube assy
36
Overload protector
26.1
Capillary tube 1
37
Set plate for thermistor
26.2
Capillary tube 2
—
26.3
Capillary joint
26.4
Sound absorber putty
Part 5 – Disassembly and Maintenance
3
55
5–7
Disassembly and Maintenance: Outdoor Units
1
1.4
ESIE02–01
RY35EAZ7V1 and RY45EAZ7V1
The illustration below shows the exploded view.
Stop valve
Exploded view
Accumulator
Service pport
3
Switch box
Capillary asy
55
5–8
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Outdoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
1
Front plate
28
Solenoid valve assy
2
Side plate right rear
29
High-pressure switch
2.1
Handgrip
30
Stop valve assy (liquid line)
3
Side plate right left
30.1
Valve cap (stop valve)
3.1
DAIKIN name plate
31
Flare nut
3.2
Handgrip
32
Stop valve assy (gas line)
3.3
R407C sticker
32.1
Valve core (service port)
4
Top plate
32.2
Cover for service port
4.1
Wiring diagram
32.3
Stop valve cover
4.2
Fault diagnosis name plate
33
Flare nut
5
Air discharge grille assy
34
Fan motor
6
Suction grille
35
Propeller fan assy
7
Bottom frame assy
36
Fan nut
8
Service cover assy
37
Switch box assy
9
Partition plate
37.1
Switch box plate
10
Fan motor stand
37.2
PCB assy
11
Compressor
37.2.1
Varistor
12
Spring holder upper
37.3
Locking guard spacer
13
Spring
37.4
Power transformer
14
Spring holder lower
37.5
Transformer fixing plate
15
Flange nut
37.6
Thermistor assy
16
Terminal cover
37.7
Magnetic contactor
17
Retainer o.l. relay
37.8
Running capacitor
18
Lead wire protection bush
37.9
Capacitor fixing band
19
Compressor sound absorber shell
37.10
Fan capacitor
20
Accumulator
37.11
Set plate for high-pressure switch
21
Accumulator sound absorber shell
37.12
Terminal strip
22
Heat exchanger assy
37.13
Wire clamp
22.1
Service port assy
37.14
Insulation strip for wire clamp
22.1.1
Valve core (service port)
37.15
Filter capacitor assy
22.1.2
Cover for service port
38
Overload protector
23
Heat exchanger fixing plate
39
Outdoor thermistor mounting plate
24
Bypass seal plate
40
Set metal (thermistor use)
25
Cushion outdoor heat exchanger
41
Strainer
26
Capillary assy
42
Accumulator cushion rubber
27
4-way valve body
43
Plate spring
Part 5 – Disassembly and Maintenance
3
55
5–9
Disassembly and Maintenance: Outdoor Units
1
1.5
ESIE02–01
R60GZ7W11
The illustration below shows the exploded view.
Strainer
Exploded view
Compressor
Gas stop valve
3
Switch box
Liquid stop vlave
55
5–10
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Outdoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
1
Front plate assy
21
Flare nut
2
Side plate back assy
22
Gas stop valve assy
2.1
Handgrip
22.1
Valve core service port
3
Side plate front assy
22.2
Cover for service port
3.1
DAIKIN name plate
22.3
Stop valve cover
3.2
R407C sticker
23
Flare nut
3.3
Handgrip
24
Strainer
4
Top plate
25
Fan motor
4.1
Wiring diagram
26
Propeller fan assy
5
Discharge grille
27
Fan nut
6
Suction grille
28
Heat exchanger fixing plate
7
Bottom frame + set plate assy
29
Cushion outdoor heat exchanger
7.1
Bottom frame assy
30
Outdoor thermistor mounting plate
7.2
Compressor set plate assy
31
Switch box assy
8
Service cover assy
31.1
Switch box plate
9
Partition plate
31.2
Fan capacitor
10
Fan motor stand
31.3
Reverse phase protector
11
Compressor with accumulator
31.4
Magnetic switch
12
Compressor rubber
31.5
Surge absorber
13
Compressor nut
31.6
Magnetic contactor
14
Terminal rubber
31.7
Thermostat
15
Terminal cover
31.8
Terminal strip
16
Terminal nut
31.9
Noise filter
17
Compresssor sound absorber shell
31.10
Wire clamp
18
Heat exchanger assy
31.11
Insulation strip for wire clamp
19
Liquid pipe asy
31.12
Locking guard spacer
19.1
Capillary tube
—
20
Liquid stop valve assy
20.1
Valve cap (stop valve)
Part 5 – Disassembly and Maintenance
3
55
5–11
Disassembly and Maintenance: Outdoor Units
1
1.6
ESIE02–01
MA56GZ7W11
Exploded view
The illustration below shows the exploded view.
Compressor
3
5–12
Branch pipe
Switch box
Stop valves
55
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Outdoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
1
Front plate
32
Union joint (liquid line)
2
Side plate back assy
33
Union joint (gas line)
2.1
Handgrip
34
Union joint (gas line)
3
Side plate front assy
35
Union joint (gas line)
3.1
DAIKIN name plate
36
Flare nut
3.2
Handgrip
37
Flare nut
3.3
R407C sticker
38
Flare nut
4
Top plate assy
39
Flare nut
4.1
Wiring diagram
40
Fan motor
5
Air discharge grille assy
41
Propeller fan
6
Suction grille
42
Fan nut
7
Bottom frame assy
43
Switch box assy
8
Service cover assy
43.1
Switch box plate
9
Partition plate
43.2
PCB assy
10
Fan motor stand
43.2.1
Fuse (printed circuit)
11
Piping mounting plate cover assy
43.2.2
Varistor
11.1
Liquid/gas indication N/P
43.3
PCB assy
12
Compressor
43.4
Reverse phase protector
13
Compressor rubber
43.5
Locking card spacer
14
Compressor nut
43.6
Power transformer
15
Terminal cover
43.7
Magnetic contactor
16
Terminal nut
43.8
Magnetic contactor
17
Terminal rubber
43.9
Fan capacitor
18
Compressor set plate assy
43.10
Noise filter
19
Set plate for thermistor
43.11
Surge absorber
20
Compressor sound absorber shell
43.12
Electronic expansion valve coil
21
Accumulator assy
43.13
Terminal strip
22
Heat exchanger assy
43.14
Terminal strip
23
Heat exchanger assy
43.15
Wire clamp (lead wire)
24
Cushion outdoor heat exchanger
43.16
Insulation strip for wire clamp
25
Low pressure control valve
43.17
Wire clamp
26
Motor valve
43.18
Insulation strip for wire clamp
27
Branch pipe
43.19
Low ambient thermostat
28
Stop valve outlet pipe assy
44
Set plate half union joint
29
Strainer
45
Set plate half union joint
30
Stop valve assy (liquid line)
46
Set plate half union joint
30.1
Valve core
47
Set plate half union joint
30.2
Blind cap
—
30.3
Valve cap (stop valve)
31
Stop valve assy (gas line)
31.1
Valve core
31.2
Blind cap
31.3
Valve cap (stop valve)
Part 5 – Disassembly and Maintenance
3
55
5–13
Disassembly and Maintenance: Outdoor Units
MA90GZ7W11
The illustration below shows the exploded view.
Switch box
Exploded view
Compressor
3
Accessories
1
1.7
ESIE02–01
Stop valve
55
5–14
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Outdoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
1
Bottom frame assy
41
Accumulator assy
2
Installation leg
42
Strainer
3
Partition plate
43
Strainer
4
Fan motor stand
44
Capillary tube bended
5
Fan motor stand mounting plate
45
Low pressure control valve
6
Front plate
46
High-pressure switch
7
Side plate front assy
47
Solenoid valve body
8
Side plate back assy
48
Solenoid valve coil assy
9
Service cover assy
49
Set screw (solenoid valve)
9.1
Wiring diagram
50
Fan motor
10
Stay
51
Fan propeller assy
11
Frame plate
52
Fan nut
12
Suction grille 1
53
Switch box metal assy
13
Suction grille 2
54
Switch box plate
14
Discharge grille assy
55
Running capacitor (fan motor)
15
Top plate assy
56
Magnetic contactor
16
Piping mounting plate cover
57
Fuse (printed circuit)
17
Piping mounting plate assy
58
Thermistor
18
Handgrip
59
Power transformer
19
Connection plate
60
PCB assy
20
DAIKIN name plate
61
PCB assy
21
R407C sticker
62
PCB assy
22
Compressor with accumulator
63
Locking card spacer
23
Compressor rubber
64
Film capacitor
24
Compressor nut
64.1
Noise filter
25
Terminal cover (compressor)
65
Terminal strip (control circuit)
26
Termnal nut (compressor)
66
Terminal strip 4p ( (control circuit)
27
Terminal rubber (compressor)
67
Terminal strip (power source)
28
Compressor sound absorber shell
68
Cable clamp
29
Heat exchanger assy
69
Cable clamp
30
Heat exchanger fixing plate
70
Cable clamp
31
Stop valve assy (liquid line)
71
Thermistor set spring
32
Valve cap
72
Discharge thermostat
33
Stop valve assy (gas line)
73
Thermistor set spring
34
Cap. stop valve
74
Low ambient thermostat
35
Union joint (liquid line)
75
Packing (reducing joint)
36
Union joint (gas line)
76
Packing (reducing joint)
37
Union joint (gas line)
77
Packing (reducing joint)
38
Motor operated body
78
Packing (reducing joint)
39
Motor valve coil
79
Reducing joint
40
Motor valve coil
80
Packing (flare nut)
Part 5 – Disassembly and Maintenance
3
55
5–15
Disassembly and Maintenance: Outdoor Units
RP71B7V1, RP71B7W1 and RP71B7T1
The illustration below shows the exploded view.
Switch box
Exploded view
Switch box
1
1.8
ESIE02–01
3
55
5–16
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Outdoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
1
Front plate 1
32
Filter
2
Front plate 2
33
Filter
3
Assy sealing side plate
34
Fan propeller
4
Top plate assy
35
Washer
5
Bottom frame assy
36
Nut with washer
6
Fixation leg
37
Receiver
7
Partition plate assy
38
Fan motor
8
DAIKIN name plate
39
Switch box body
9
Stop valve mounting plate
40
Magnetic contactor + OC
10
Fan motor base
41
Starting relay
11
Air discharge grille
42
PCB assy
12
Air suction grille
42.1
Glass tube fuse
13
Handle
43
PCB assy
14
Compressor scroll
44
Transformer
15
Rubber cushion pre-assy
45
Air thermistor
16
Nut with washer
46
Heat exchanger thermistor
17
Bolt for compressor
47
Discharge thermistor
18
Compresser sound absorber
48
Resin PCB support
19
Heat exchanger
49
Running capacitor compressor
20
Motor valve body
50
Running capacitor compressor
21
Coil motor valve
51
Start capacitor compressor
22
Solenoid valve coil
52
Capacitor fan motor
23
Solenoid valve
53
Resistor assy
24
High-pressure switch
54
Terminal strip
25
Low-pressure switch
55
Locking card spacer
26
Charge valve
56
Compressor cable assy
26.1
Valve core (service port)
57
Thermistor fixing plate
26.2
Blinde cap (service port)
58
Thermistor mounting spring
27
Stop valve assy
59
Thermistor mounting spring
28
Stop valve assy
60
Stop valve cover
29
Service cap
61
Bottom tray assy
30
Flare nut
62
Packing case shell
31
Flare nut
63
Packing cushion assy
Part 5 – Disassembly and Maintenance
3
55
5–17
Disassembly and Maintenance: Outdoor Units
RYP71B7V1 and RYP71B7W1
The illustration below shows the exploded view.
Switch box
Exploded view
Switch box
1
1.9
ESIE02–01
3
55
5–18
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Outdoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
1
Front plate 1
34
Filter
2
Front plate 2
35
Filter
3
Assy sealing side plate
36
Fan propeller
4
Top plate assy
37
Washer
5
Bottom plate assy
38
Nut with washer
6
Fixation leg
39
Fan motor
7
Partition plate assy
40
Switch box body
8
Stop valve mounting plate
41
Magnetic contactor + OC
9
Fan motor base
42
Starting relay
10
Air discharge grille
43
PCB assy
11
Suction grille
43.1
Glass tube fuse
12
Handle
44
PCB assy
13
Compressor scroll
45
Transformer
14
Rubber cushion pre-assy
46
Air thermistor
15
Nut with washer
47
Heat exchanger thermistor
16
Bolt for compressor
48
Discharge thermistor
17
Compressor sound absorber
49
Resin PCB support
18
Heat exchanger
50
Running capacitor compressor
19
Receiver
51
Running capacitor compressor
20
4-way valve
52
Start capacitor compressor
21
Coil 4-way valve
53
Capacitor fan motor
22
Motor valve body
54
Resistor assy
23
Coil motor valve
55
Terminal strip
24
Solenoid valve coil
56
Locking card spacer
25
Solenoid valve
57
Compressor cable assy
26
High-pressure switch
58
Thermistor fixing plate
27
Low-pressure switch
59
Thermistor mounting spring
28
Charge valve
60
Thermistor mounting spring
28.1
Valve core (service port)
61
Filter
28.2
Blind cap (service port)
62
DAIKIN name plate
29
Stop valve assy
63
Stop valve cover
30
Stop valve assy
64
Bottom tray assy
31
Service cap
65
Packing case shell
32
Flare nut
66
Packing cushion assy
33
Flare nut
—
Part 5 – Disassembly and Maintenance
3
55
5–19
Disassembly and Maintenance: Outdoor Units
RP100B7V1, RP100B7W1, RP100B7T1, RP125B7W1 and RP125B7T1
The illustration below shows the exploded view.
Switch box
Exploded view
Switch box
1
1.10
ESIE02–01
3
55
5–20
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Outdoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
1
Front plate 1
34
Fan propeller
2
Front plate 2
35
Washer
3
Side plate
36
Nut with washer
4
Top plate assy
37
Receiver
5
Bottom frame assy
38
Fan motor
6
Fixation leg
39
Fan motor
7
Partition plate assy
40
Switch box body
8
DAIKIN name plate
41
Magnetic contactor + OC
9
Stop valve mounting plate
42
Starting relay
10
Fan motor base
43
PCB assy
11
Air discharge grille
43.1
Glass tube fuse
12
Air suction grille
44
PCB assy
13
Handle
45
Transformer
14
Compressor scroll
46
Air thermistor
15
Rubber cushion pre-assy
47
Heat exchanger thermistor
16
Nut with washer
48
Discharge thermistor
17
Bolt for compressor
49
Resin PCB support
18
Compressor sound absorber
50
Running capacitor compressor
19
Heat exchanger assy
51
Running capacitor compressor
20
Motorized expansion valve
52
Start capacitor compressor
21
Coil of motor valve
53
Capacitor fan motor
22
Solenoid valve coil
54
Resistor assy
23
Solenoid valve
55
Terminal strip
24
High-pressure switch
56
Locking card spacer
25
Low-pressure switch
57
Compressor cable assy
26
Charge valve
58
Compressor cable assy
26.1
Valve core (service port)
59
Clamp for harness
26.2
Blind cap (service port)
60
Thermistor fixing plate
27
Stop valve assy
61
Thermistor mounting spring
28
Stop valve assy
62
Thermistor mounting spring
29
Service cap
63
Stop valve cover
30
Flare nut
64
Bottom tray assy
31
Flare nut
65
Packing case shell
32
Filter
66
Packing cushion assy
33
Filter
—
Part 5 – Disassembly and Maintenance
3
55
5–21
Disassembly and Maintenance: Outdoor Units
RYP100B7V1, RYP100B7W1 and RYP125B7W1
The illustration below shows the exploded view.
Switch box
Exploded view
Switch box
1
1.11
ESIE02–01
3
55
5–22
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Outdoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
1
Front plate 1
35
Filter
2
Front plate 2
36
Filter
3
Side plate
37
Fan propeller
4
Top plate assy
38
Washer
5
Bottom frame assy
39
Nut with washer
6
Fixation leg
40
Filter
7
Partition plate assy
41
Fan motor
8
DAIKIN name plate
42
Fan motor
9
Stop valve mounting plate
43
Switch box body
10
Fan motor base
44
Magnetic contactor + OC
11
Air discharge grille
45
Starting relay
12
Air suction grille
46
PCB assy
13
Handle
46.1
Glass tube fuse
14
Compressor scroll
47
PCB assy
15
Rubber cushion pre-assy
48
Transformer
16
Nut with washer
49
Air thermistor
17
Bolt for compressor
50
Heat exchanger thermistor
18
Compressor sound absorber
51
Discharge thermistor
19
Heat exchanger
52
Resin PCB support
20
Receiver
53
Running capacitor compressor
21
4-way valve
54
Running capacitor compressor
22
Coil 4-way valve
55
Start capacitor compressor
23
Motor valve body
56
Capacitor fan motor
24
Coil of motor valve
57
Resistor assy
25
Solenoid valve coil
58
Terminal strip
26
Solenoid valve
59
Locking card spacer
27
High-pressure switch
60
Compressor cable assy
28
Low-pressure switch
61
Cable holders
29
Charge valve
62
Clamp for harness
29.1
Valve core (service port)
63
Thermistor fixing plate
29.2
Blind cap (service port)
64
Thermistor mounting spring
30
Stop valve assy
65
Thermistor mounting spring
31
Stop valve assy
66
Stop valve cover
32
Service cap
67
Bottom tray assy
33
Flare nut
68
Packing case shell
34
Flare nut
69
Packing cushion assy
Part 5 – Disassembly and Maintenance
3
55
5–23
Disassembly and Maintenance: Outdoor Units
1
1.12
ESIE02–01
RP200B7W1 and RP250B7W1
Exploded view
The illustration below shows the exploded view.
3
55
5–24
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Outdoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
A1
A2
A3
A4
A5
A6
A7
A8
B1
B1.1
B2
B3
B4
B5
B6
B7
B8
B8.1
B8.2
B8.3
B9
B10
B11
B12
B13
B14
C1
C1.1
E1
E2
E3
E4
E4.1
E5
Compressor
Rubber cushion pre-assy
Hexagon bolt
Round plain washer for wood
Insulation cover
Head cover
Insulation cover
Crankcase heater
Heat exchanger assy
Distributor assy
Liquid receiver assy
Filter
Low-pressure switch
Stop valve assy
Packing for flange
Hexagon bolt
Check valve
Fitting body
Valve core
Service port
High-pressure switch
Motor operated valve body
Solenoid valve body
Solenoid valve coil
Filter
Stop valve assy
Fan blade assy
Set screw
Switch box assy
Switch box main body
Switch box cover assy
PCB assy
Glass tube fuse
Magnetic contactor / Electromagnetic
switch
Terminal and cover
PCB assy
Locking guard spacer
Resin PCB support
Capacitor
PCB assy
Power supply transformer
Power supply fixing case
Air thermistor
Heat exchanger thermistor
Discharge thermistor
Fan motor
E20
E22
E23
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F23
K1
K3
K3.1
K3.2
K4
L1.1
L1.2
L1.3
L1.4
L1.5
L1.6
Fan motor
Thermistor clamp
Coil motorized valve
Side plate right
Side plate left
Front plate upper
Front plate lower
Front plate lower
Fan motor base
Upper stay
Bypass prevention plate
Support rear
Support front
Top plate air outlet
Discharge grille
Suction grille
Stop valve mounting plate assy
Cover
Bottom plate (sheet metal)
Foundation leg
Thermistor mounting spring
Thermistor mounting spring
Trough hole cover
DAIKIN name plate
Supplied pip (gas side)
Mating flange
Packing for flange
Supplied pipe (gas side)
Wire harness
E6
E7
E8
E9
E11
E12
E13
E15
E16
E17
E18
E19
Part 5 – Disassembly and Maintenance
3
55
L1.7
L1.8
L1.9
L1.10
L1.11
L1.12
L1.13
L1.14
L1.15
L1.16
L1.17
L1.18
5–25
Disassembly and Maintenance: Outdoor Units
1
1.13
ESIE02–01
RYP200B7W1 and RYP250B7W1
Exploded view
The illustration below shows the exploded view.
3
55
5–26
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Outdoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
A1
A2
A3
A4
A5
A6
A7
A8
B1
B1.1
B2
B3
B3.1
B3.2
B3.3
B3.4
B3.5
B3.6
B3.6.1
B3.6.2
B3.6.3
B3.7
B3.8
B3.9
B4
B4.1
B4.2
B4.3
B4.4
B4.5
B4.6
B4.7
C1
C1.1
E1
E2
E3
E4
E4.1
E5
Compressor
Rubber cushion pre-assy
Hexagon bolt
Round plain washer for wood
Insulation cover
Head cover
Insulation cover
Crankcase heater
Heat exchanger assy
Distributor assy
Liquid receiver assy
4-way valve assy
Filter
Muffler
4-way valve body
High-pressure switch
Low-pressure switch
Check valve
Fitting body
Valve core
Service port
Stop valve assy
Packing for flange
Hexagon bolt
Motor operated valve assy
Motor operated valve body
Solenoid valve
Solenoid valve coil assy
Filter
Check valve
Check valve
Stop valve assy
Fan blade assy
Set screw
Switch box assy
Switch box main body
Switch box cover assy
PCB assy
Glass tube fuse
Magnetic contactor / Electromagnetic
switch
Terminal and cover
PCB assy
Locking guard spacer
Resin PCB support
Capacitor
PCB assy
Power supply transformer
Power supply fixing case
Air thermistor
Heat exchanger thermistor
E18
E19
E20
E22
E23
E24
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F23
K1
K3
K3.1
K3.2
K4
L1.1
L1.2
L1.3
L1.4
L1.5
L1.6
L1.7
L1.8
L1.9
Discharge thermistor
Fan motor
Fan motor
Thermistor clamp
Coil motorized valve
4-way valve coil assy
Side plate right
Side plate left
Front plate upper
Front plate lower
Front plate lower
Fan motor base
Upper stay
Bypass prevention plate
Support rear
Support front
Top plate air outlet
Discharge grille
Suction grille
Stop valve mounting plate assy
Cover
Bottom plate (sheet metal)
Foundation leg
Thermistor mounting spring
Thermistor mounting spring
Trough hole cover
DAIKIN name plate
Supplied pipe (gas side)
Mating flange
Packing for flange
Supplied pipe (gas side)
Wire harness
E6
E7
E8
E9
E11
E12
E13
E15
E16
E17
Part 5 – Disassembly and Maintenance
3
55
L1.10
L1.11
L1.12
L1.13
L1.14
L1.15
L1.16
L1.17
L1.18
—
5–27
Disassembly and Maintenance: Outdoor Units
ESIE02–01
1
3
55
5–28
Part 5 – Disassembly and Maintenance
ESIE02–01
Disassembly and Maintenance: Indoor Units
Part 5
1
2
Disassembly and Maintenance: Indoor Units
2.1
What Is in This Chapter?
Introduction
Overview
This chapter contains the following information on the indoor units:
■
Exploded views
■
Components.
3
This chapter contains the following topics:
Topic
See page
2.2–FHC35BZ7V1, FHC45BZ7V1, FHC60BZ7V1, FHYC35BZ7V1,
FHYC45BZ7V1, FHYCP35B7V1, FHYCP45B7V1, FHYCP60B7V1 and
FHYCP71B7V1
5–30
2.3–FHYBP35B7V1 and FHYBP45B7V1
5–32
2.4–FHYBP60B7V1 and FHYBP71B7V1
5–34
2.5–FHYBP100B7V1 and FHYBP125B7V1
5–36
2.6–FDYP125B7V1, FDYP200B7V1 and FDYP250B7V1
5–38
2.7–FHYC71BZV1, FHYC100BZV1 and FHYC125BZV1
5–40
2.8–FH35BZV1, FH45BZV1, FHYP35BV1 and FHYP45BV1
5–42
2.9–FH60BZV1, FHYP60BV1 and FHYP71BV1
5–44
2.10–FHK35BZV1, FHK45BZV1, FHK60BZV1, FHYKP35BV1, FHYKP45BV1,
FHYKP60BV1 and FHYKP71BV1
5–46
2.11–FHYP100BV1 and FHYP125BV1
5–48
2.12–FUYP71BV17
5–50
2.13–FUYP100BV17 and FUYP125BV17
5–52
2.14–FAYP71BV1 and FAYP100BV1
5–54
Part 5 – Disassembly and Maintenance
55
5–29
Disassembly and Maintenance: Indoor Units
1
2.2
ESIE02–01
FHC35BZ7V1, FHC45BZ7V1, FHC60BZ7V1, FHYC35BZ7V1,
FHYC45BZ7V1, FHYCP35B7V1, FHYCP45B7V1, FHYCP60B7V1
and FHYCP71B7V1
Exploded view
The illustration below shows the exploded view.
3
55
5–30
Part 5 – Disassembly and Maintenance
ESIE02–01
Disassembly and Maintenance: Indoor Units
1
Components
The table below contains the components of the exploded view.
No.
Component
No.
Component
B1
Heat exchanger assy
E24
Float switch
B1.1
Distributor with filter
E25
Fan motor
B1.2
Single union joint
F1
Casing assy
B1.3
Single union joint
F6
Inspection cover assy
B1.4
Flare nut
F8
Drain pan assy
B1.5
Flare nut
F8.1
Drain plug
C1
Fan rotor (turbo)
F9
Sound absorbing material
C2
Lock washer
F10
Heat exchanger blind plate assy
C3
Nut with washer
F11
Heat exchanger mounting plate
E1
Switch box assy
F12
Hold plate assy
E2
Switch box body
F13
Panel mounting plate
E4
Bell mouth
F14
Drain pump mounting plate
E5
Switch box cover assy 1
F15
Vibration isolator
E6
Switch box cover 2
F16
Hexagon mounting bolt
E7.1
PCB assy
F17
Vibration isolator
E7.1.1
Air thermistor
F18
Nut with washer
E9
Capacitor
F19
Feeler bulb clamp
E10
Terminal
F21
Rubber bush
E11
Terminal block
F22
Inner heat insulator
E12
Power supply transformer
G1
Drain hose
E13
Wire harness
G2
Hose band
E14
Wire harness
H1
Top tray assy
E15
Wire harness
H2
Bottom tray assy
E16
Wire harness
K1
Drain hose assy
E19
Grounding wire
K2
Hose band
E20
Grounding screw
K3
Insulation for joint (liquid)
E21
Thermistor (liquid)
K4
Insulation for joint (gas)
E23
Drain pump
K5
Sealing material
Part 5 – Disassembly and Maintenance
3
55
5–31
Disassembly and Maintenance: Indoor Units
FHYBP35B7V1 and FHYBP45B7V1
3
Fan assy
55
Accessories
The illustration below shows the exploded view.
Switch box
Exploded view
Drain pump assy
1
2.3
ESIE02–01
5–32
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Indoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
1
Top plate assy
31.1
Fan top plate
2
Right plate assy
31.2
Fan housing bottom
3
Left plate assy
31.3
Fan housing top
4
Interchangeable plate
31.4
Rotor assy
5
Small bottom plate
31.4.1
Hexagon socket screw
6
Large bottom plate
31.5
Fan motor
7
Air outlet flange
31.6
Fan motor stand
8
Center stay assy
31.7
Motor fixing plate assy
9
Air filter holding plate assy
31.8
Rotor assy
10
Stay for fan top panel assy
31.8.1
Hexagon socket screw
11
Fan side blind plate assy
31.9
Shaft assy
12
Cooler side blind plate assy
31.10
Coupling
13
Pipe setting plate assy
31.11
Vibro proof rubber assy
14
Swtich box cover assy
31.12
Bearing board
15
Drain pan setting plate
31.13
Bearing fixing plate
16
Drain socket cover assy 1
32
Switch box body
17
Drain socket cover assy 2
33
Switch box fixing plate
18
Suspension bracket
34
Terminal fixing plate
19
Drain pan assy
35
Option fixing plate left
19.1
Drain socket cap
36
Option fixing plate right
20
Heat exchanger assy
37
PCB assy
20.1
Distributor with filter assy
37.1
Air thermistor
20.2
Single union joint
38
Power supply transformer
20.3
Single union joint
39
Fan motor capacitor
20.4
Flare nut
40
Terminal for remote control
20.5
Flare nut
41
Terminal for power supply
21
Air filter assy
42
Wire harness
22
Service cover assy
43
Wire harness
23
Drain pump fixing plate
44
Wire harness
24
Service cover cap assy
45
Wire harness
25
Drain pump
46
Tie wrap with clip
26
Float switch
47
Thermistor (liquid)
27
Drain hose assy
48
Thermistor fixing blade
28
Vibration absorber
49
Metal clamp
29
Plain washer
50
Drain hose
30
Fitting bolt drain pump
51
Insulation for joint (gas)
31
Fan assy
52
Insulation for joint (liquid)
Part 5 – Disassembly and Maintenance
3
55
5–33
Disassembly and Maintenance: Indoor Units
FHYBP60B7V1 and FHYBP71B7V1
Fan assy
3
Accessories
The illustration below shows the exploded view.
Switch box
Exploded view
Drain pump assy
1
2.4
ESIE02–01
55
5–34
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Indoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
1
Top plate assy
31.1
Fan top plate
2
Right plate assy
31.2
Fan housing bottom
3
Left plate assy
31.3
Fan housing top
4
Interchangeable plate
31.4
Rotor assy
5
Small bottom plate
31.4.1
Hexagon socket screw
6
Large bottom plate
31.5
Fan motor
7
Air outlet flange
31.6
Fan motor stand
8
Center stay assy
31.7
Motor fixing plate assy
9
Air filter holding plate assy
31.8
Rotor assy
10
Stay for fan top panel assy
31.8.1
Hexagon socket screw
11
Fan side blind plate assy
31.9
Shaft assy
12
Cooler side blind plate assy
31.10
Coupling
13
Pipe setting plate assy
31.11
Vibro proof rubber assy
14
Swtich box cover assy
31.12
Bearing board
15
Drain pan setting plate
31.13
Bearing fixing plate
16
Drain socket cover assy 1
32
Switch box body
17
Drain socket cover assy 2
33
Switch box fixing plate
18
Suspension bracket
34
Terminal fixing plate
19
Drain pan assy
35
Option fixing plate left
19.1
Drain socket cap
36
Option fixing plate right
20
Heat exchanger assy
37
PCB assy
20.1
Distributor with filter assy
37.1
Air thermistor
20.2
Single union joint
38
Power supply transformer
20.3
Single union joint
39
Fan motor capacitor
20.4
Flare nut
40
Terminal for remote control
20.5
Flare nut
41
Terminal for power supply
21
Air filter assy
42
Wire harness
22
Service cover assy
43
Wire harness
23
Drain pump fixing plate
44
Wire harness
24
Service cover cap assy
45
Wire harness
25
Drain pump
46
Tie wrap with clip
26
Float switch
47
Thermistor (liquid)
27
Drain hose assy
48
Thermistor fixing blade
28
Vibration absorber
49
Metal clamp
29
Plain washer
50
Drain hose
30
Fitting bolt drain pump
51
Insulation for joint (gas)
31
Fan assy
52
Insulation for joint (liquid)
Part 5 – Disassembly and Maintenance
3
55
5–35
Disassembly and Maintenance: Indoor Units
FHYBP100B7V1 and FHYBP125B7V1
Fan assy
3
Accessories
The illustration below shows the exploded view.
Switch box
Exploded view
Drain pump assy
1
2.5
ESIE02–01
55
5–36
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Indoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
1
Top plate assy
31.1
Fan top plate
2
Right plate assy
31.2
Fan housing bottom
3
Left plate assy
31.3
Fan housing top
4
Interchangeable plate
31.4
Rotor assy
5
Small bottom plate
31.4.1
Hexagon socket screw
6
Large bottom plate
31.5
Fan motor
7
Air outlet flange
31.6
Fan motor stand
8
Center stay assy
31.7
Motor fixing plate assy
9
Air filter holding plate assy
31.8
Rotor assy
10
Stay for fan top panel assy
31.8.1
Hexagon socket screw
11
Fan side blind plate assy
31.9
Shaft assy
12
Cooler side blind plate assy
31.10
Coupling
13
Pipe setting plate assy
31.11
Vibro proof rubber assy
14
Swtich box cover assy
31.12
Bearing board
15
Drain pan setting plate
31.13
Bearing fixing plate
16
Drain socket cover assy 1
32
Switch box body
17
Drain socket cover assy 2
33
Switch box fixing plate
18
Suspension bracket
34
Terminal fixing plate
19
Drain pan assy
35
Option fixing plate left
19.1
Drain socket cap
36
Option fixing plate right
20
Heat exchanger assy
37
PCB assy
20.1
Distributor with filter assy
37.1
Air thermistor
20.2
Single union joint
38
Power supply transformer
20.3
Single union joint
39
Fan motor capacitor
20.4
Flare nut
40
Terminal for remote control
20.5
Flare nut
41
Terminal for power supply
21
Air filter assy
42
Wire harness
22
Service cover assy
43
Wire harness
23
Drain pump fixing plate
44
Wire harness
24
Service cover cap assy
45
Wire harness
25
Drain pump
46
Tie wrap with clip
26
Float switch
47
Thermistor (liquid)
27
Drain hose assy
48
Thermistor fixing blade
28
Vibration absorber
49
Metal clamp
29
Plain washer
50
Drain hose
30
Fitting bolt drain pump
51
Insulation for joint (gas)
31
Fan assy
52
Insulation for joint (liquid)
Part 5 – Disassembly and Maintenance
3
55
5–37
Disassembly and Maintenance: Indoor Units
1
2.6
ESIE02–01
FDYP125B7V1, FDYP200B7V1 and FDYP250B7V1
The illustration below shows the exploded view.
Switch box
Exploded view
3
55
5–38
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Indoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
1
Top plate assy
6.20
Terminal strip
2
Fan assy + fan mounting plate
6.21
Thermistor
3
Side plate right
6.22
Thermistor
4
Side plate left
6.23
Tie wrap with clip
5
Service cover assy
6.24
PCB assy
6
Switch box assy
6.25
Power supply transformer
6.1
Switch box fixing plate
6.26
Grounding wire
6.2
PCB assy power supply
6.27
Insulation switch box
6.3
Terminal fixing plate
6.28
Insulation switch box
6.4
Magnetic contactor
6.29
Insulation switch box
6.5
PCB assy
7
Hook
6.6
Switch box body
8
Filter cover
6.7
Option fixing plate left
9
Fixture heat exchanger right
6.8
Option fixing plate right
10
Fixture heat exchanger left
6.9
Wire harness
11
Bypass sealing plate
6.10
Wire harness
12
Heat exchanger assy
6.11
Wire harness power supply
13
Drain pan assy
6.12
Wire harness power supply
14
Bottom plate assy
6.14
Wire harness
15
Air filter
6.15
Wire harness
16
Pipe fixing plate
6.16
Wire harness
17
Clamp
6.17
Wire harness
18
Clamp
6.18
PCB assy
19
Thermistor (fixing)
6.19
Locking guard spacer
—
Part 5 – Disassembly and Maintenance
3
55
5–39
Disassembly and Maintenance: Indoor Units
1
2.7
ESIE02–01
FHYC71BZV1, FHYC100BZV1 and FHYC125BZV1
Exploded view
The illustration below shows the exploded view.
3
55
5–40
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Indoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
B1
Evaporator assy
E24
Heat exchanger thermistor
B1.1
Distributor with strainer
E25
Fan motor
B1.2
Union joint (gas line)
F1
Casing frame assy
B1.3
Union joint (liquid line)
F2
Cover inspection window
B1.4
Flare nut
F3
Heat insulation cover assy
B1.5
Flare nut
F4
Top flat plate
C1
Fan rotor (turbo)
F5
Drain pan assy
C2
Lock washer
F5.1
Drain plug
C3
Hexagon lock nut
F6
Bell mouth
E1
Electric component assy
F7
Cover switch box
E2
Switch box
F8
Cover switch box
E3
Set plate electric devices
F9
Fixture panel
E4
Printed circuit
F10
Blind plate heat exchanger
E4.1
Printed circuit
F11
Set plate heat exchanger
E4.1.1
Air thermistor
F12
Retainer piping
E4.2
Adaptor (capacity control)
F13
Rubber bush
E5
Terminal block
F14
Vibration isolator fan motor
E6
Terminal block
F15
Flange nut
E7
Power transformer
F16
Set bolt drain pump
E9
Capacitor
F17
Fixture feeler
E10
Tapping screw
F20
Bolts and nuts list
E12
Tie wrap
G1
Drain hose assy
E13
Wire harness
G2
Hose band
E14
Wire harness
K1
Drain hose assy
E15
Wire harness
K2
Hose band
E18
Wire harness
K3
Insulation tube (gas line)
E19
Grounding terminal
K4
Insulation tube (liquid line)
E23
Drain pump assy
K5
Operation manual
E23.1
Drain pump
K6
Sealer drain hose
E23.2
Set plate drain pump
K7
Sealer drain hose
E23.3
Float switch
—
E23.4
Vibration isolator drain pump
Part 5 – Disassembly and Maintenance
3
55
5–41
Disassembly and Maintenance: Indoor Units
1
2.8
ESIE02–01
FH35BZV1, FH45BZV1, FHYP35BV1 and FHYP45BV1
Exploded view
The illustration below shows the exploded view.
3
55
5–42
Part 5 – Disassembly and Maintenance
ESIE02–01
Disassembly and Maintenance: Indoor Units
Components
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
No.
Component
B1
B1.1
B1.2
B1.3
B1.4
B1.5
B1.6
Evaporator assy
Distributor
Union joint (gas line)
Union joint (liquid line)
Flare nut
Flare nut
Retainer thermistor
E12
E13
E14
E15
E16
E17
E18
Wire harness (feed back)
Wire harness (fan motor)
Wire harness (swing motor)
Wire harness (power unit)
Wire harness (power unit)
Thermistor
Wire clip
F9
F10
F10.1
F10.2
F10.2.1
F10.2.2
F10.2.3
C1
C1.1
C1.2
C1.3
C1.4
C1.4.1
C1.5
C1.5.1
C1.6
C1.7
C1.8
C1.9
C1.10
C1.11
C1.12
C1.13
Fan assy
Top plate fan assy
Fan housing
Fan housing
Fan rotor
Hexagon socket screw
Fan rotor
Hexagon socket screw
Fan motor
Lock metal fan motor
Motor base
Fan shaft
Coupling fan shaft
Fan bearing
Bearing holder
Set plate bearing holder
E19
E20
E21
E22
E23
E24
F1
F2
F2.1
F2.1.1
F2.1.2
F3
F3.1
F3.2
F3.3
F3.4
F10.3
F11
F12
F12.1
F12.2
F12.3
F12.4
F13
F14
F14.1
F14.2
F14.3
F15
F15.1
F16
F17
C1.14
C2
E1
E2
E3
E4
E5
Wire clip
Air filter
Electric components assy
Switch box
Cover switch box
Printed circuit (power unit)
Printed circuit
F3.5
F3.6
F3.7
F3.8
F3.9
F3.10
F3.11
Clamp
Lock metal
Wire clip
Bush thermistor
Sound absorbing material
Housing power unit
Top plate assy
Bottom plate assy
Name plate assy
Housing signal receiver
DAIKIN name plate
Side plate assy (right)
Side plate (right)
Swing motor assy
Set plate swing motor
Connecting arm horizontal
vane
Crank air swing
Bearing horizontal vane
Heat insulation material
Heat insulation material
Heat insulation material
Sealer
Sealer
Set plate drain pan
Drain pan assy
Insulation tube
Vertical vane air discharge
Set plate vertical vane
Vertical vane air discharge
Connecting bar vertical
vane
Cap drain socket
Supporter
Horizontal vane assy
Horizontal vane
Rod horizontal vane
Rod horizontal vane
Rod horizontal vane
Decorative plate
Air suction grille assy
Air suction grille
Fixture air suction grille
Hinge air suction grille
Side plate assy
Cover side plate
Side plate (left)
Blind plate piping hole
E5.1
E5.1.1
E5.1.2
E5.2
E6
E7
E8
E9
E10
E10.1
E10.2
E11
Printed circuit (control unit)
Air thermistor
Connector
Capacity control adaptor
Plastic case
Capacitor fan motor
Terminal block
Terminal block
Wire harness (transmission)
Fuse holder
Fuse
Wire harness (remote control)
F3.12
F3.13
F4
F4.1
F4.2
F4.3
F4.4
F4.5
F5
F6
F7
F8
Lock metal
Wire clip
Side plate assy
Side plate (left)
Bearing horizontal vane
Heat insulation material
Heat insulation material
Heat insulation material
Hook metal
Hook metal
Side plate heat exchanger
Retainer refrigerant piping
F25
F27
F28
F29
F30
K1
K2
K3
K4
K5
K6
K7
Part 5 – Disassembly and Maintenance
F18
F19
F20
F21
F22
F23
F24
Blind plate piping hole
Wire clip
Set plate drain pan
Supporter fan
Retainer
Air guide plate
Heat insulation cover top
plate
Insulation cover piping hole
Protector heat exchanger
Heat insulation cover
Heat insulation cover
Suspension bolt
Drain hose
Hose band
Insulation tube (liquid line)
Insulation tube (gas line)
Sealer
Sealer
Operation manual
5–43
3
55
Disassembly and Maintenance: Indoor Units
1
2.9
ESIE02–01
FH60BZV1, FHYP60BV1 and FHYP71BV1
Exploded view
The illustration below shows the exploded view.
3
55
5–44
Part 5 – Disassembly and Maintenance
ESIE02–01
Disassembly and Maintenance: Indoor Units
Components
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
No.
Component
B1
B1.1
B1.2
B1.3
B1.4
B1.5
B1.6
C1
C1.1
C1.2
C1.3
C1.4
C1.4.1
C1.5
C1.5.1
C1.6
C1.7
C1.8
C1.9
C1.10
C1.11
C1.12
Evaporator assy
Distributor
Union joint (gas line)
Union joint (liquid line)
Flare nut
Flare nut
Retainer thermistor
Fan assy
Top plate fan assy
Fan housing
Fan housing
Fan rotor
Hexagon socket screw
Fan rotor
Hexagon socket screw
Fan motor
Lock metal fan motor
Motor base
Fan shaft
Coupling fan shaft
Fan bearing
Bearing holder
E13
E14
E15
E16
E17
E18
E19
E20
E21
E22
E23
E24
F1
F2
F2.1
F2.1.1
F2.1.2
F3
F3.1
F3.2
F3.3
F3.4
F10.1
F10.2
F10.2.1
F10.2.2
F10.2.3
F10.2.4
F10.3
F11
F12
F12.1
F12.2
F12.3
F12.4
F13
F14
F14.1
F14.2
F14.3
F15
F15.1
F16
F17
Insulation tube
Vertical vane air discharge
Set plate vertical vane
Vertical vane air discharge
Connect. bar vertical vane
Connect. bar vertical vane
Cap drain socket
Supporter
Horizontal vane assy
Horizontal vane
Rod horizontal vane
Rod horizontal vane
Rod horizontal vane
Decorative plate
Air suction grille assy
Air suction grille
Fixture air suction grille
Hinge air suction grille
Side plate assy
Cover side plate
Side plate (left)
Blind plate piping hole
C1.13
C1.14
C2
E1
E2
E3
E4
Set plate bearing holder
Wire clip
Air filter
Electric components assy
Switch box
Cover switch box
Printed circuit (power unit)
F3.5
F3.6
F3.7
F3.8
F3.9
F3.10
F3.11
Wire harness (fan motor)
Wire harness (swing motor)
Wire harness (power unit)
Wire harness (power unit)
Thermistor
Wire clip
Wire clip
Lock metal
Clamp
Bush thermistor
Sound absorbing material
Housing power unit
Top plate assy
Bottom plate assy
Name plate assy
Housing signal receiver
DAIKIN name plate
Side plate assy (right)
Side plate (right)
Swing motor assy
Set plate swing motor
Connecting arm horizontal
vane
Crank air swing
Bearing horizontal vane
Heat insulation material
Heat insulation material
Heat insulation material
Sealer
Sealer
F18
F19
F20
F21
F22
F23
F24
E5
E5.1
E5.1.1
E5.1.2
E5.2
E6
E7
E8
E9
E10
E10.1
E10.2
E11
Printed circuit
Printed circuit (control unit)
Air thermistor
Connector
Capacity control adaptor
Plastic case
Capacitor fan motor
Terminal block
Terminal block
Wire harness (transmission)
Fuse holder
Fuse
Wire harness (remote control)
Wire harness (feed back)
F3.12
F3.13
F4
F4.1
F4.2
F4.3
F4.4
F4.5
F5
F6
F7
F8
F9
Lock metal
Wire clip
Side plate assy
Side plate (left)
Bearing horizontal vane
Heat insulation material
Heat insulation material
Heat insulation material
Hook metal
Hook metal
Side plate heat exchanger
Retainer refrigerant piping
Set plate drain pan
F25
F27
F28
F29
F30
K1
K2
K3
K4
K5
K6
K7
—
Blind plate piping hole
Wire clip
Set plate drain pan
Supporter fan
Retainer
Air guide plate
Heat insulation cover top
plate
Insulation cover piping hole
Protector heat exchanger
Heat insulation cover
Heat insulation cover
Suspension bolt
Drain hose
Hose band
Insulation tube (liquid line)
Insulation tube (gas line)
Sealer
Sealer
Operation manual
F10
Drain pan assy
E12
Part 5 – Disassembly and Maintenance
5–45
3
55
Disassembly and Maintenance: Indoor Units
FHK35BZV1, FHK45BZV1, FHK60BZV1,
FHYKP35BV1, FHYKP45BV1, FHYKP60BV1 and FHYKP71BV1
Detail A
3
Switch box
The illustration below shows the exploded view.
Accessories
Exploded view
Remote control
1
2.10
ESIE02–01
Decoration panel
55
5–46
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Indoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
1
Top plate
22.6
Fan motor
2
Partition plate drain pump
22.7
Motor base
3
Side plate fan chamber
22.8
Fan shaft
4
Front plate assy
22.9
Coupling
5
Wiring cover
22.10
Fan bearing
6
Blind plate ducting hole
23
Swtich box without devices
7
Drain pan holder
24
Cover switch box
8
Blind cover
25
Cover switch box
9
Cover piping hole
26
Printed circuit (control unit)
10
Suspend metal
26.1
Air thermistor
11
Suspend metal
26.2
Thermistor
12
Drain pan assy
27
Locking guard spacer
13
Drain hose
28
Transformer
14
Drain pump
29
Running capacitor
15
Buffer rubber drain pump
30
Terminal block
16
Set plate drain pump
31
Fuse holder
17
Float switch
32
Fuse control circuit
18
Fitting metal decoration panel
33
Remote control
19
Fitting metal decoration panel
33.1
Bottom case remote control
20
Fitting metal decoration panel
33.2
Lead wire remote control
21
Evaporator
34
Drain hose
21.1
Union joint (liquid line)
35
Hose band
21.2
Union joint (gas line)
36
Hose band
21.3
Filter
37
Drain pipe
22
Fan assy with motor
38
Insulation tube
22.1
Top plate fan assy
39
Insulation tube
22.2
Fan housing
40
Hook remote control
22.3
Fan housing
41
Staple
22.4
Clamp metal fan motor
42
Blind air discharge
22.5
Fan motor
43
Blind air discharge
Part 5 – Disassembly and Maintenance
3
55
5–47
Disassembly and Maintenance: Indoor Units
1
2.11
ESIE02–01
FHYP100BV1 and FHYP125BV1
Exploded view
The illustration below shows the exploded view.
3
55
5–48
Part 5 – Disassembly and Maintenance
ESIE02–01
Disassembly and Maintenance: Indoor Units
Components
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
No.
Component
B1
Evaporator assy
E13
Wire harness (fan motor)
F10.1
Insulation tube
B1.1
Distributor
E14
Wire harness (swing motor)
F10.2
Vertical vane air discharge
B1.2
Union joint (gas line)
E15
Thermistor
F10.2.1
Set plate vertical vane
B1.3
Union joint (liquid line)
E16
Wire clip
F10.2.2
Vertical van air discharge
B1.4
Flare nut
E17
Wire clip
F10.2.3
Connect. bar vertical vane
B1.5
Flare nut
E18
Lock metal
F10.3
Cap drain socket
B1.6
Retainer thermistor
E19
Clamp
F11
Supporter horizontal vane
C1
Fan assy
E20
Bush thermistor
F12
Horizontal vane assy
C1.1
Top plate fan assy
E21
Sound absorbing material
F12.1
Horizontal vane
C1.2
Fan housing
E21
Sound absorbing material
F12.2
Rod horizontal vane
C1.3
Fan housing
F1
Top plate assy
F12.3
Rod horizontal vane
C1.4
Fan rotor
F2
Bottom plate assy
F12.4
Rod horizontal vane
C1.4.1
Hexagon socket screw
F2.1
Name plate assy
F13
Decorative plate
C1.5
Fan rotor
F2.1.1
Housing signal receiver
F14
Air suction grille assy
C1.5.1
Hexagon socket screw
F2.1.2
DAIKIN name plate
F14.1
Air suction grille
C1.6
Fan motor
F3
Side plate assy (right)
F14.2
Fixture air suction grille
C1.7
Lock metal fan motor
F3.1
Side plate (right)
F14.3
Hinge air suction grille
C1.8
Motor base
F3.2
Swing motor assy
F15
Side plate assy
C1.9
Fan shaft assy
F3.3
Set plate swing motor
F16
Side plate assy
C1.10
Coupling fan shaft
F3.4
Connecting arm horizontal
vane
F16.1
Cover side plate
C1.11
Fan bearing
F3.5
Crank air swing
F17
Blind plate piping hole
C1.12
Bearing holder
F3.6
Bearing horizontal vane
F18
Blind plate piping hole
C1.13
Set plate bearing holder
F3.7
Heat insulation material
F19
Wire clip
3
55
C1.14
Wire clip
F3.8
Heat insulation material
F20
Set plate drain pan
C2
Air filter
F3.9
Heat insulation material
F21
Supporter fan
E1
Electronic components assy
F3.10
Heat insulation material
F22
Retainer
E2
Switch box
F3.11
Sealer
F23
Air guide plate
E3
Cover switch box
F3.12
Lock metal
F24
Heat insulation cover piping
hole
E4
Power transformer
F3.13
Wire clip
F25
Insulation cover piping hole
E5
Printed circuit
F4
Side plate assy
F27
Protector heat exchanger
E5.1
Printed circuit (control unit)
F4.1
Side plate (left)
F28
Heat insulation cover
E5.1.1
Air thermistor
F4.2
Bearing horizontal vane
F29
Heat insulation cover
E5.1.2
Connector
F4.3
Heat insulation material
F30
Suspension bolt
E5.2
Capacity control adaptor
F4.4
Heat insulation material
K1
Drain hose
E6
Platic case
F4.5
Heat insulation material
K2
Hose band
E7
Capacitor fan motor
F5
Hook metal
K3
Insulation tube (liquid line)
E8
Terminal block
F6
Hook metal
K4
Insulation tube (gas line)
E9
Terminal block
F7
Side plate heat exchanger
K5
Sealer
E10
Wire harness (transmission)
F8
Retainer
K6
Sealer
E11
Wire harness (remote control)
F9
Set plate drain pan
K7
Operation manual
E12
Wire harness (feed back)
F10
Drain pan assy
—
Part 5 – Disassembly and Maintenance
5–49
Disassembly and Maintenance: Indoor Units
1
2.12
ESIE02–01
FUYP71BV17
Exploded view
The illustration below shows the exploded view.
Detail B arrow view
3
55
5–50
Part 5 – Disassembly and Maintenance
ESIE02–01
Disassembly and Maintenance: Indoor Units
Components
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
No.
Component
B1
Heat exchanger assy
F3
Side plate assy swing unit
F12
B1.1
Distributor
F3.1
Side plate
F13
B1.2
Union joint (gas line)
F3.2
Air swing unit
F14
B1.3
Union joint (liquid line)
F3.2.1
Air swing motor
F15
B1.4
Flare nut
F3.2.2
Limit switch
F16
B1.5
C1
C2
E1
E2
E3
E4
E4.1
E4.1.1
E4.2
E5
Flare nut
Rotor assy
Lock nut fan rotor
Electric components assy
Switch box
Set plate control devices
PCB assy
Printed circuit (control)
Air thermistor
Capacity setting adaptor
Printed circuit (power unit)
F3.2.3
F3.2.4
F3.2.5
F3.2.6
F3.2.7
F3.2.8
F4
F4.1
F4.2
F4.3
F5
F17
F18
F19
F20
F21
F22
F23
F24
F25
F25.1
F26
E5.1
E6
E7
E8
E9
E10
E11
E12
F6
F7
F8
F8.1
F8.2
F8.3
F8.3.1
F8.3.2
F27
F28
F29
F30
F31
F32
F32.1
F32.2
Air adjust plate
Retainer lead wire
Retainer thermistor
Set bolt fan motor
Vibration isolator fan motor
Set plate drain pump
Set base drain pump
Float switch
E13
E14
E15
E16
E17
E18
E19
E20
E22
Fuse
Terminal block
Capacitor
Terminal block
Wire harness (transmission)
Wire harness (power unit)
Wire harness (power unit)
Wire harness (PCB terminal)
Grounding wire
Wire clip
Wire clip
Edge saddle
Cover switch box
Housing power unit
Wire harness (fan motor)
Drain pump
Heat exchanger thermistor
Bearing assy (right)
Bearing assy (left)
Joint
Air swing motor base
Cover air swing motor
Cam air swing
Side plate assy
Side plate
Bearing assy (right)
Bearing assy (left)
Hook metal refrigerant piping
Hook metal
Hook metal
Air suction grille assy
Air suction grille
Reinforcement plate
Air dilection lever assy
Lever air suction grille
Spring air suction grille
Decorative frame air discharge
Decorative frame air discharge
Decorative frame air discharge
Horizontal vane air discharge
Horizontal vane air discharge
Blind plate pipng hole
Partition plate evaporator
Blind plate heat exchanger
Fitting plate evaporator
Retainer refrigerant piping
Cover inspection hole
Bell mouth
Drain hose assy
Drain pan assy
Drain plug
Heat insulator (internal)
F32.3
F34
F35
K2
K3
K4
K5
K6
K7
Buffer rubber drain pump
Set bolt fan motor
Plain washer
Insulation cover (liquid line)
Insulation tube (gas line)
Hose band
Drain hose
Drain pipe joint
Lead wire remote control
E23
E24
F1
F2
F2.1
F2.2
Fan motor
Grounding wire
Top plate
Side plate assy
Side plate
Joint assy
F10.1
F10.2
F10.3
F10.4
F10.5
F11
Air direction lever assy
Air filter
Reinforcement metal grille
DAIKIN name plate
Reinforcement plate
Corner cover assy
Corner cover
Corner cover
Corner cover refrigerant
piping
Corner cover upper
Corner cover lower
Internal corner cover
Internal corner cover
Tapping screw
Decorative frame air discharge
K8
K9
K10
K11
K12
K13
Sealer drain hose
Staple
Pan head wood screw
Shelter air discharge grille
Lock plate insulator
Lock plate insulator
Part 5 – Disassembly and Maintenance
F8.4
F8.5
F8.6
F8.7
F8.8
F9
F9.1
F9.2
F10
5–51
3
55
Disassembly and Maintenance: Indoor Units
1
2.13
ESIE02–01
FUYP100BV17 and FUYP125BV17
Exploded view
The illustration below shows the exploded view.
Detail B arrow view
3
55
5–52
Part 5 – Disassembly and Maintenance
ESIE02–01
Disassembly and Maintenance: Indoor Units
Components
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
No.
Component
B1
Heat exchanger assy
F3
Side plate assy swing unit
F13
B1.1
Distributor
F3.1
Side plate
F14
B1.2
Union joint (gas line)
F3.2
Air swing unit
F15
B1.3
Union joint (liquid line)
F3.2.1
Air swing motor
F16
B1.4
B1.5
C1
C2
C3
E1
E2
E3
E4
E4.1
E4.1.1
E4.2
E5
E5.1
E6
E7
E8
E9
E10
E11
E12
F3.2.2
F3.2.3
F3.2.4
F3.2.5
F3.2.6
F3.2.7
F3.2.8
F4
F4.1
F4.2
F4.3
F5
F6
F7
F8
F8.1
F8.2
F8.3
F8.3.1
F8.3.2
F8.4
Limit switch
Bearing assy (right)
Bearing assy (left)
Joint
Air swing motor base
Cover air swing motor
Cam air swing
Side plate assy
Side plate
Bearing assy (right)
Bearing assy (left)
Hook metal refr. piping
Hook metal
Hook metal
Air suction grille assy
Air suction grille
Reinforcement plate
Air dilection lever assy
Lever air suction grille
Spring air suction grille
Air direction lever assy
F17
F18
F19
F20
F21
F22
F23
F24
F25
F25.1
F26
F27
F28
F29
F30
F31
F32
F32.1
F32.2
F32.3
F34
E13
E14
E15
E16
E17
E18
E19
E20
Flare nut
Flare nut
Rotor assy
Lock nut fan rotor
Lock washer
Electric components assy
Switch box
Set plate control devices
PCB assy
Printed circuit (control)
Air thermistor
Capacity setting adaptor
Printed circuit (power unit)
Fuse
Terminal block
Capacitor
Terminal block
Wire harness (transmission)
Wire harness (power unit)
Wire harness (power unit)
Wire harness (PCB terminal)
Grounding wire
Wire clip
Wire clip
Edge saddle
Cover switch box
Housing power unit
Wire harness (fan motor)
Drain pump
Decorative frame air discharge
Decorative frame air discharge
Horizontal vane air discharge
Horizontal vane air discharge
Blind plate pipng hole
Partition plate evaporator
Blind plate heat exchanger
Fitting plate evaporator
Retainer refrigerant piping
Cover inspection hole
Bell mouth
Drain hose assy
Drain pan assy
Drain plug
Heat insulator (internal)
Air adjust plate
Retainer lead wire
Retainer thermistor
Set bolt fan motor
Vibration isolator fan motor
Set plate drain pump
Set base drain pump
Float switch
Buffer rubber drain pump
Set bolt fan motor
F8.5
F8.6
F8.7
F8.8
F9
F9.1
F9.2
F10
F35
F36
K2
K3
K4
K5
K6
K7
Plain washer
Air guide plate assy
Insulation cover (liquid line)
Insulation tube (gas line)
Hose band
Drain hose
Drain pipe joint
Lead wire remote control
E22
E23
E24
F1
F2
F2.1
Heat exchanger thermistor
Fan motor
Grounding wire
Top plate
Side plate assy
Side plate
F10.1
F10.2
F10.3
F10.4
F10.5
F11
K8
K9
K10
K11
K12
K13
Sealer drain hose
Staple
Pan head wood screw
Shelter air discharge grille
Lock plate insulator
Lock plate insulator
F2.2
Joint assy
F12
Air filter
Reinforcement metal grille
DAIKIN name plate
Reinforcement plate
Corner cover assy
Corner cover
Corner cover
Corner cover refrigerant
piping
Corner cover upper
Corner cover lower
Internal corner cover
Internal corner cover
Tapping screw
Decorative frame air discharge
Decorative frame air discharge
K14
Lock plate insulator
Part 5 – Disassembly and Maintenance
5–53
3
55
Disassembly and Maintenance: Indoor Units
1
2.14
ESIE02–01
FAYP71BV1 and FAYP100BV1
Exploded view
The illustration below shows the exploded view.
3
55
5–54
Part 5 – Disassembly and Maintenance
ESIE02–01
Components
Disassembly and Maintenance: Indoor Units
1
The table below contains the components of the exploded view.
No.
Component
No.
Component
B1
Evaporator assy
E2
Printed circuit
B1.1
Evaporator assy
E2.1
Capacity setting adaptor
B1.2
Auxiliary pipe (gas line)
E3
Printed circuit (power unit)
B1.2.1
Union joint (gas line)
E4
Housing power unit
B1.2.2
Flare nut
E5
Terminal block
B1.3
Auxiliary pipe (liquid line)
E6
Terminal block
B1.3.1
Union joint
E7
Running capacitor
B1.3.2
Flare nut
E8
Thermistor
B1.4
Capillary tube assy
E9
Heat exchanger thermistor
B1.4.1
Distributor
E10
Wire harness
B1.4.2
Strainer
E11
Fan motor
B1.4.3
Capillary tube
F1
Front grille assy
B1.4.4
Capillary tube
F2
Air filter
B1.4.5
Capillary tube
F3
Air filter
B1.5
Sound absorbing putty
F4
Side plate assy (right)
B1.6
Sound absorbing putty
F5
Side plate assy (left)
B1.7
Sound absorbing putty
F6
Fan scroll assy (right)
B2
Fitting spring thermistor
F7
Fastener
C1
Fan rotor
F8
Partition plate (left)
C2
Fan rotor
F8.1
Fan bearing assy
C3
Air discharge grille assy
F9
Indicator cover
C3.1
Air discharge grille
F10
Bottom frame assy
C3.2
Air discharge grille
F11
Heat insulation cover (right)
C3.3
Air discharge grille
F12
Drip proof cover bottom frame
C3.4
Air discharge unit
F13
Top plate
C3.5
Drain pan assy
F14
Insulation cover bottom plate
C3.6
Drain socket
F15
Bottom plate
C3.7
Horizontal vane assy
F16
Insulation cover bottom plate
C3.8
Vertical vane air discharge
F17
Clamp refrigerant piping
C3.9
Connecting arm
F18
Motor base
C3.10
Connecting arm
F19
Cover fan motor
C3.11
Bearing
F20
Mounting plate
C3.12
Rod
F21
Plate air discharge grille
C3.13
Crank air swing
F22
Heat insulation cover (left)
C3.14
Crank rod air swing
F23
Fan scroll assy (left)
C3.15
Crank. air swing
K1
Staple
C3.16
Swing motor base
K2
Lead wire remote control
C3.17
Air swing motor
K3
Screw kit
C3.18
Drain hose
K4
Insulation tape
C4
Bearing holder
K5
Insulation cover joint
C5
Fan bearing
K5.1
Insulation tube gas line
E1
Switch box
K5.2
Heat insulation material
Part 5 – Disassembly and Maintenance
3
55
5–55
Disassembly and Maintenance: Indoor Units
ESIE02–01
1
3
55
5–56
Part 5 – Disassembly and Maintenance
ESIE02–01
Index
1
Numerics
4-way valve control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–45
3
A
A1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
auto-restart function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
k
k
k
k
k
k
3–22
3–23
3–25
3–27
3–28
2–22
4
B
BS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–22
C
5
C4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–30
C9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–30
ceiling height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–15
centralized group No.
setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–18
changing
field settings, infrared remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–12
field settings, wired remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–11
maintenance mode settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–20
checking
discharge pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–70
expansion valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–71
fan motor hall IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–66
installation condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–69
power supply wave form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–67
refrigerant system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–68
test run checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–4
thermistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–72
CJ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–32
components
exploded views, indoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 5–29
exploded views, outdoor units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 5–3
functional diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–71
general outline, indoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–27
general outline, outdoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–3
infrared remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–12
PCB layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–145
switch box layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–95
wired remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–10
wiring diagrams, indoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–135
wiring diagrams, outdoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–115
condensation avoidance control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–35
control modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–7
crankcase heater control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–18
Index
i
ESIE02–01
1
D
defrost control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–38
diameters, pipe connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–71
dimensions
indoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–27
outdoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–3
DIP switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–22
discharge pipe temperature control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–16
draft avoidance control
1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–41
2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–43
drain pump control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–19
dry keep mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–26
DS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–24
DS2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–25
3
E
E0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–34
E3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–39
E4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–41
E9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–43
EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–22
electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–57
emergency operation
general. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–8
switching to . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–10
error codes
indoor malfunctions overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–11
outdoor malfunctions overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–12
system malfunctions overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–13
exploded views
indoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 5–29
outdoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 5–3
4
5
F
F3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–45
factory settings
indoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–14
fan and flap operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–21
fan control
normal, cooling mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–32
normal, heating mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–47
starting, cooling or dry keep mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–30
starting, heating mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–46
field settings
BS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–22
DIP switches overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–22
jumpers overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–22
levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–19
overview indoor units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–13
filter counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–16
forced operating mode
general. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–8
switching to . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–10
forced thermostat OFF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–13
freeze-up function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–27
functional diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–71
ii
Index
ESIE02–01
1
G
gas shortage function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–17
H
H3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
H9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
high pressure protection control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
high-pressure switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HPS and LPS function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
k
k
k
k
k
3–47
3–48
2–34
3–19
2–14
3
I
identification function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–44
installation space
indoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–27
outdoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–3
intelligent control mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–28
4
J
J1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
J3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
J3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
J6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
k
k
k
k
k
4–23
4–23
3–50
3–51
4–23
5
L
LEDs
troubleshooting with indoor unit LEDs and remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–11
troubleshooting with outdoor unit LEDs and remote control, outdoor unit malfunctions . . . . . . . k 3–12
troubleshooting with outdoor unit LEDs and remote control, system malfunctions. . . . . . . . . . . k 3–13
locating
exploded views, indoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 5–29
exploded views, outdoor units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 5–3
functional diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–71
general outline, indoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–27
general outline, outdoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–3
infrared remote control components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–12
PCB layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–145
switch box layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–95
thermistors, large h/p . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–5
thermistors, small h/p . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–4
wired remote control components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–10
wiring diagrams, indoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–135
wiring diagrams, outdoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–115
low outside temperature control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–33
low-pressure switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–20
M
MAIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
malfunctions
indoor error codes overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
outdoor error codes overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
system error codes overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
motor operated valve control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index
k 4–17
k
k
k
k
3–11
3–12
3–13
2–49
iii
ESIE02–01
1
N
noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–5
O
operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–7
operation data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–28
operation range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–27
options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–57
outlook
indoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–27
outdoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–3
overcurrent relay compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–17
3
P
PCBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–145
4
R
R1T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–73
R2T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–73
R3T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–74
remote control
setting address for infrared remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–6
setting address for receiver of infrared remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–5
thermostat, using conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–23
reverse phase protector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–18
5
S
safety devices
high-pressure switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–19
low-pressure switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–20
overcurrent relay compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–17
overview indoor units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–14
overview outdoor units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–15
reverse phase protector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–18
thermal protector fan motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–16
service space
indoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–27
outdoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–3
setting
address for infrared remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–6
address for receiver of infrared remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–5
ceiling height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–15
centralized group No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–18
field settings, infrared remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–12
field settings, wired remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–11
filter counter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–16
MAIN/SUB when using two remote controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–17
iv
Index
ESIE02–01
1
settings
BS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ceiling height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
changing maintenance mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIP switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
factory overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
field overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
filter counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
jumpers overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAIN/SUB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
maintenance mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
possible system settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
simulated operation function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SUB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
switch boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
4–22
4–15
4–20
4–22
4–14
4–13
4–16
4–22
4–17
4–21
4–20
2–15
1–57
4–17
1–95
3
T
technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–57
test run
checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 4–4
thermal protector fan motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–16
thermistors
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–72
functions, large h/p . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–5
functions, small h/p . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–4
locating, large h/p . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–5
locating, small h/p . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–4
R1T and R2T. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–73
R3T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–74
thermostat control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–11
4
5
U
U0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
U1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
U4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
U5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
U8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
k
k
k
k
k
k
k
3–54
3–55
3–57
3–60
3–61
3–62
3–57
V
vibrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 3–5
W
wiring diagrams
indoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–135
outdoor units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1–115
Y
year round cooling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 2–33
Index
v
ESIE02–01
1
3
4
5
vi
Index
Daikin Europe N.V. is approved by LRQA for its Quality
Management System in accordance with the ISO9001
standard. ISO9001 pertains to quality assurance
regarding design, development, manufacturing as well
as to services related to the product.
Daikin units comply with the European regulations that
guarantee the safety of the product.
ISO14001 assures an effective environmental
management system in order to help protect human
health and the environment from the potential impact
of our activities, products and services and to assist in
maintaining and improving the quality of the
environment.
Zandvoordestraat 300
B-8400 Ostend - Belgium
Internet: http://www.daikineurope.com
ESIE02-01 • 09/2002
Prepared in Belgium by Vanmelle
Specifications are subject to change without prior notice
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising