- No category
advertisement
▼
Scroll to page 2
of 8
Inline Centrifugal Fans for Round Duct the ultimate in quality, quiet performance and cost efficiency FR Series FX Series FKD Series Fantech FR Series Versatility and Value Fantech’s versatile FR Series fans feature a plastic housing constructed of UL-recognized, UV-protected thermoplastic resin. This tough protective shell allows the fan to be mounted in outdoor and wet locations.* Ideal for multiple point exhaust, dual bathroom exhaust, or new room additions, Fantech’s FR Series fans are caulked at the motor screws, the wiring cables and along the seams of the fan to prevent moisture from entering the housing. Fantech’s FR Series fans have long been the choice of residential builders and remodelers but now can be used for commercial projects with our recent UL commercial applications rating. Easy to install Loaded with features Hot air and steam vented through roof vent DB10 Switch •Prewired and supplied with a mounting bracket for easy installation •Available singularly with bracket or in a variety of kits for specific applications. Each kit includes the appropriate fan and accessories •Tested and approved by UL, CSA, or equals •Approved for residential and commercial applications and for wet locations •Suitable for airstream temperatures up to 140° F •Easy connection using external wiring box with waterproof gasket •122-649 CFM •4” to 10” duct diameters •100% speed controllable •Five-year factory warranty Fantech FR Series Fan Duct Dryer Boosting Two Baths… One Solution! Hot air and steam vented through roof vent Fantech FR Series Fan Dual vent points, one for each bathroom Bath #2 Bath #1 Kits are available for the following applications: •Dryer Boosting Kit (DBF 110) for boosting clothes dryer installations with extended duct runs •Regular Kits (REG 100 and REG 140) for single point exhaust applications •Deluxe Kits (DLX 110, DLX 150, and DLX 200) designed for dual point exhaust applications •Vent Light Kits (REG 100L, DLX 150L) for single and dual vent light exhaust applications Typical attic installation New Addition… No Problem! New Supply Drop #2 New Supply Drop #2 Add Fantech FR Series Inline Booster Fan New Addition Existing House New ‘T’ Connector into Existing Duct Run * The FR Series is not manufactured to operate with water running through the motor compartment, or to be used in applications where the fan would be buried underground. A UL-recognized waterproof conduit should be used for all outdoor applications to prevent moisture entry via knockout in wiring box. 2 Fantech Fan Guide Book FR Kits Pictured from left to right: DBF110 – Dryer Boosting Kit; DLX150 – Dual Point Ventilation Kit; REG100L – Single Vent Light Kit. Additional kits (not pictured) are available. DBF110 DLX150 REG100L Specifications FR Series Dimensional Data model FR 100 FR 110 FR 125 FR 140 FR 150 †A1 4 4 — 6 6 A2 5 5 5 6¹₄ 6¹₄ C 9¹₂ 9¹₂ 9¹₂ 11³₄ 11³₄ D 6¹₈ 6¹₈ 6¹₈ 5⁷₈ 5⁷₈ E ⁷₈ ⁷₈ ⁷₈ 1 1 F ⁷₈ ⁷₈ — ⁷₈ ⁷₈ FR 160 FR 200 FR 225 FR 250 6 8 8 — 6¹₄ 10 10 10 11³₄ 13¹₄ 13¹₄ 13¹₄ 6³₈ 6¹₄ 6¹₄ 6¹₄ 1 1¹₂ 1¹₂ 1¹₂ ⁷₈ 1¹₂ 1¹₂ — Side View E A2 Top View F A1 A1 A2 All dimensions in inches. † Duct connections are 1/8” smaller than duct size. D C FR Series Air Performance Graphs 3.00 1.60 1.40 2.50 1.20 Static Pressure (in H2O) Static Pressure (in H2O) FR110 1.00 FR150 0.80 FR100 0.60 2.00 FR250 1.50 FR225 1.00 0.40 FR200 FR140 0.20 0.00 0.50 FR160 FR125 0.00 0 50 100 150 200 250 0 100 200 300 400 500 600 700 Flow Rate (CFM) Flow Rate (CFM) FR Series Performance Data Fan Energy Model Star FR FR FR FR FR FR FR FR FR 100 110 125 140 150 160 200 225 250 √ — √ √ √ — √ √ — RPM Volts Rated Watts 2900 2900 2950 2850 2750 2750 2750 3100 2850 115 115 115 115 120 115 115 115 115 19 80 18 61 71 129 122 137 241 Wattage Range 13 62 15 47 54 103 106 111 146 – – – – – – – – – 19 80 18 62 72 130 128 152 248 Max. Amps 0.18 0.72 0.18 0.53 0.67 1.14 1.11 1.35 2.40 Static Pressure in Inches W.G. 0” 122 167 148 214 263 289 408 429 649 .2” 100 150 120 190 230 260 360 400 600 .4” 78 133 88 162 198 233 308 366 553 .6” 55 113 47 132 167 206 259 332 506 .8” 15 88 — 99 136 179 213 297 454 1.0” — 63 — 46 106 154 173 260 403 Max. 1.5” — 4 — — 17 89 72 168 294 Max. Ps 0.87” 1.60” 0.79” 1.15” 1.58” 2.32” 2.14” 2.48” 2.58” Duct Dia. 4” 4” 5” 6” 6” 6” 8” 8” 10” FR Series performance is shown with ducted outlet. Per HVI’s Certified Ratings Program, charted air flow performance has been derated by a factor based on actual test results and the certified rate at .2 inches WG. Fantech “Your Ventilation Solutions Company” 3 Fantech FX Series From Residential to Commercial The Fantech FX Series’ galvanized steel housing makes these fans ideal for various commercial code and residential applications. Home uses include range hood exhaust, duct boosting, bathroom exhaust and dryer boosting. Office applications include intake, exhaust, filtration, return or makeup air systems that require mounting versatility, high efficiency, low sound levels, and ease of service. Fantech FX Series fans are a snap to install. Prewired and supplied with a mounting bracket, they can be mounted at any angle in any point along the ductwork. Straight-through airflow design also helps simplify installation. FX Series fans are designed to work with standard dimensions of spiral duct, eliminating the need for transition pieces. Hard working. Long lasting. Here’s why: •Galvanized steel housing features baked powdercoat finish, perfect for commercial code applications •Powered by external rotor motorized impeller for excellent heat dissipation, even at low RPM •Tested and approved by UL, CSA, or equals •Suitable for airstream temperatures up to 140° F •4" to 12" circular duct diameters •Airflow from 117-801 CFM •External rotor motor, Class B insulation for long and maintenance-free operation •Automatic reset thermal overload protection •Permanently lubricated sealed ball bearings •True airfoil backward curved impeller •External wiring box for ease of connection •100% speed controllable •Five-year factory warranty Quiet Kitchen Ventilation Hot air and steam vented through roof vent 110V Power Supply Fantech FX Series Fan Range Hood Wire Suspension FC Vibration Isolating Clamps Duct Fantech external rotor motor 4 Fantech Fan Guide Book Fantech FX Series Fan Inline Boosting Detail FX Kits DBF4XL – Dryer Boosting fan kit. The perfect solution to dryer blues. For applications when an extended duct length is required. Specifications Side View FX Series Dimensional Data †A 4 4 5 5 6 6 8 model FX 4 FX 4XL FX 5 FX 5XL FX 6 FX 6XL FX 8 C 8 9¹⁄₂ 8 9¹⁄₂ 11¹⁄₂ 13¹⁄₄ 13¹⁄₄ D 5¹₂ 5¹₂ 5¹₄ 5 6 6¹₂ 6¹₄ E ⁷₈ ⁷₈ ⁷₈ ⁷₈ ³₄ 1 1 Top View F E F ⁷₈ ³₄ ⁷₈ 1 ⁷₈ ³₄ ⁷₈ A 2" A FX 8XL 8 13¹⁄₄ 6¹₄ 1 ⁷₈ FX 10 10 13¹⁄₄ 6¹₄ 1 1¹₄ FX 10XL 10 13¹⁄₄ 6¹₄ 1 1¹₄ FX 12 12 16 8¹₄ 1 1¹₄ FX 12XL 12 16 8¹₄ 1 1¹₄ All dimensions in inches. † Duct connections are 1/8” smaller than duct size. A D C FX Series Air Performance Graphs 3.00 4.00 3.50 2.50 3.00 Static Pressure (in H2O) Static Pressure (in H2O) FX12 2.00 1.50 1.00 FX6 2.50 FX12XL 2.00 1.50 FX10XL 1.00 FX8 FX6XL 0.50 FX5 FX4 FX4XL 0.00 0 100 200 300 400 500 Flow Rate (CFM) FX8XL 0.50 FX10 600 700 800 0.00 0 100 FX5XL 200 300 400 500 Flow Rate (CFM) 600 700 800 FX Series Performance Data (For sound performance data refer to publication #FX-0799) Static Pressure in Inches W.G. Max. Duct Ps Dia. 0” .125” .25” .375” .5” .75” 1.0” 1.25” 1.5” FX 4 2950 115 19 0.17 117 101 86 72 58 — — — — 0.81” 4” FX 4XL 2800 115 83 0.73 148 139 130 120 111 90 68 42 — 1.65” 4” 2950 115 19 0.17 132 115 98 81 65 — — — — 0.89” 5” FX 5 FX 5XL 2650 115 87 0.76 191 175 161 146 131 102 75 45 — 1.61” 5” FX 6 2700 115 84 0.74 257 241 221 197 178 143 99 59 — 1.60” 6” 2950 115 147 1.26 392 368 346 326 305 263 228 191 150 2.27” 6” FX 6XL FX 8 2600 115 116 1.02 481 444 403 361 319 237 177 130 76 2.04” 8” FX 8XL 2950 115 152 1.31 521 496 469 440 411 345 282 231 180 2.29” 8” 3000 115 147 1.27 521 499 475 448 418 357 293 234 176 2.28” 10” FX 10 FX 10XL 3000 115 242 2.11 590 565 541 519 496 442 394 339 290 2.79” 10” FX 12 2450 115 196 1.70 711 675 627 576 521 382 284 220 166 2.65” 12” 373 3.21 801 783 765 747 729 692 655 611 566 3.69” 12” FX 12XL 3250 115 Performance shown is for installation type D - Ducted inlet, Ducted outlet. Speed (RPM) shown is nominal. Performance is based on actual speed of test. Performance ratings do not include the effects of appurtenances in the airstream. Fan Model RPM Volts Max. Max. Watts Amps Fantech, Inc. certifies that the FX Series shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 211 and AMCA Publication 311 and comply with the requirements of the AMCA Certified Ratings Program. Fantech “Your Ventilation Solutions Company” 5 Fantech FKD Series Inline Mixed Flow Duct Fans With Fantech’s FKD Series fans, “going with the flow” has never been easier. These fans are specifically designed to bridge the transition between centrifugal and axial by combining the high flow of axial designs with the higher pressure, non-overloading characteristics of backward curved impellers. Fantech’s “The Straight Way” inline designs minimize system losses while being extremely compact. The round inline design keeps air moving in ductwork sized from 8” to 20”. 100% speed controllability gives extreme flexibility where there is need for varying airflow. The lightweight, compact design FKD Series fans mount at any angle, at any point along the ductwork. Fans pictured: Top– FKD12XL; Left–FKD10; and Bottom–FKD12S. A balancing act that’s easy to perform With FKD Series fans, system balancing is achieved by measuring the system flow or pressure and adjusting the fan performance by “dialing in” or setting the fan speed using inexpensive solid state speed controls, transformers or VFDs. Direct drive eliminates the need for continuous belt alignment, tension adjustment and ongoing maintenance. FYI: FKD’s performance features: Transparent view of a FKD 10 •Galvanized steel housing features baked powdercoat finish •External rotor motor with built-in thermal overload protection and automatic reset •Tested and approved by UL and CSA (or equals) •Suitable for airstream temperatures up to 140° F •Permanently lubricated sealed ball bearings •100% speed controllable for highly efficient and economical airflow •Airflow up to 6291 CFM •Terminal box with prewired electrical strip •Mixed flow impeller •Excellent heat dissipation to ensure long motor life •Three-year warranty Threaded Suspension Rod Duct Fantech’s FKD external rotor motor – built to last. 6 Fantech Fan Guide Book Prewired Electrical Box Inline Fan Detail Fantech FKD Series Fan Specifications FKD Series Dimensional Data Side View – FKD8XL FKD Air Performance Graphs Side View – FKD12XL 3.50 E ³⁄₄" A C A2 A1 A C F E E D Static Pressure (in H2O) 3.00 2.50 2.00 FKD18XL 1.50 FKD14XL 1.00 D model A C D E FKD 8XL FKD 10 8 10 12¹⁄₂ 12¹⁄₂ 15¹⁄₂ 12¹₂ 7 7 FKD 10XL FKD 12S FKD 12 FKD 14S 10 12 12 14 14 12¹⁄₂ 14 14 15 10 12¹⁄₂ 8 7 8 8 † FKD10XL 0.00 A1 12 12 14 14 16 16 18 18 A2 14 14 16 16 18 18 20 20 1000 2000 3000 4000 Flow Rate (CFM) 5000 6000 7000 3.00 FKD20 C 17⁷⁄₈ 17⁷⁄₈ 19³⁄₄ 19³⁄₄ 22¹⁄₈ 22¹⁄₈ 28¹⁄₄ 28¹⁄₄ D 18⁷⁄₈ 17¹⁄₄ 20¹⁄₄ 18³⁄₄ 23¹⁄₄ 21³⁄₄ 29¹⁄₄ 27¹⁄₄ E ⁷⁄₈ 1 1¹⁄₂ 1¹⁄₂ 1¹⁄₄ 1¹⁄₄ 2 2 Static Pressure (in H2O) A 12 14 14 16 16 18 18 20 0 3.50 All dimensions in inches. † FKD 14s overall length is 8”. model FKD 12XL FKD 14 FKD 14XL FKD 16 FKD 16XL FKD 18 FKD 18XL FKD 20 FKD16XL FKD12XL FKD8XL 0.50 F 1⁵⁄₈ 1⁵⁄₈ 1⁴⁄₈ 1⁵⁄₈ 1⁵⁄₈ 1⁵⁄₈ 1³⁄₄ 1³⁄₄ 2.50 2.00 FKD12 FKD14S 1.50 FKD18 FKD16 1.00 FKD10 FKD12S 0.50 0.00 All dimensions in inches 0 FKD14 1000 2000 3000 4000 Flow Rate (CFM) 5000 6000 7000 FKD Series Performance Data (For sound performance data refer to publication #FKD-0803 and FKD-1100/2) Fan Model RPM FKD FKD FKD FKD FKD FKD FKD FKD FKD FKD FKD FKD FKD FKD 2700 115 327 2700 115 329 2850 115 529 2700 115 323 2900 115 531 1700 115 500 2900 115 525 1700 115 495 1550 115 738 1600 115 742 1600 115 1421 1600 115 1411 1700 460/3 2208 1750 460/3 2218 8XL 10 10XL 12S 12 12XL 14S 14 14XL 16 16XL 18 18XL 20 Max. Max. Volts Watts Amps 2.99 3.011 4.842 2.951 4.862 4.802 4.812 4.762 7.122 6.392 12.403 12.043 3.75 3.73 1 Static Pressure in Inches W.G. 0” 836 910 1266 930 1305 2016 1305 2156 2619 2952 4274 4448 6236 6291 .125” 799 873 1226 889 1266 1920 1261 2061 2517 2831 4144 4992 6115 6174 .25” 761 836 1187 848 1228 1832 1218 1965 2416 2707 4014 4130 5995 6054 .375” 720 795 1147 804 1189 1746 1174 1868 2303 2580 3880 3991 5874 5933 .5” 680 752 1100 758 1145 1649 1125 1764 2180 2445 3743 3871 5754 5829 .75” 595 653 1006 657 1054 1423 1025 1520 1936 2144 3452 3583 5500 5617 1.0” 499 547 911 550 948 1066 923 1193 1662 1804 3137 3239 5199 5307 1.25” 393 432 810 443 833 606 814 623 1294 1306 2794 2843 4909 4987 1.5” 286 342 696 343 712 — 703 — 843 774 2379 2380 4602 4667 2.0” — — 460 — 479 — 469 — — — 1242 1231 3703 3757 Max. Duct Ps. Dia. 2.59” 8” 2.60” 10” 3.08” 10” 2.54” 12” 3.08” 12” 1.52” 12” 3.12” 14” 1.52” 14” 1.94” 14” 1.90” 16” 2.42” 16” 2.51” 18” 3.24” 18” 3.27” 20” Sones † 14.1 15.3 21 15.2 23 18.7 23 18.4 19.0 18.5 25 24 32 33 Fantech, Inc. certifies that the FKD Series shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 211 and AMCA Publication 311 and comply with the requirements of the AMCA Certified Ratings Program. Performance shown is for installation type D - Ducted inlet, Ducted outlet. Speed (RPM) shown is nominal. Performance is based on actual speed of test. Performance ratings do not include the effects of appurtenances in the airstream. † The sound ratings shown are loudness values in fan sones at 5ft. (1.5m) in hemispherical free field calculated per AMCA Standard 301. Values shown are for installation Type D: ducted inlet fan sone levels. Ratings do not include the effect of duct end correction. All sone values shown are calculated at 0.5” (static pressure in inches W.G.). Note: Three phase motors are wound for 230/460 volt. Motors are prewired for 460 volts but may be delivered as 230 volt or may be rewired in the field. 1 Recommended speed control rating 5A. 2 Recommended speed control rating 10A. 3 Recommended speed control rating 15A. Fantech “Your Ventilation Solutions Company” 7 Inlet and Exhaust Accessories Adjustable Metal Grills–MGE Adjustable Plastic Grills–PGE Designer Grills–DG Soffit Vent–UEV Adjustable Supply Grills–PGS Roof Caps-RC Vent Light Combination Grill–VLC Intake Guards–IG Louvered Shutters–VK & HS 8 Fantech Fan Guide Book
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project