Zephyr | Venezia ZVE-E42AS | Installation guide | Zephyr Venezia ZVE-E42AS Installation guide

Zephyr Venezia ZVE-E42AS Installation guide
Use, Care, and Installation Guide
www.zephyronline.com
Venezia
ZVE-E30AS
ZVE-E36AS
ZVE-E42AS
Model number:
Serial Number:
JUL08.0201 © Zephyr Corporation
www.zephyronline.com
INSTALLATION
Ducting Calculation Sheet .......................................
Mounting Height & Clearance................................
Ducting Options ...........................................................
Hood Speci cations ...................................................
Mounting the Range Hood ......................................
Ductless Recirculating ..............................................
5
6
7
8
9
10
FEATURES & CONTROLS
Touch Controls ............................................................. 11
Charcoal Filter Replace Reminder ...................... 12
Metal Mesh Filter Clean Reminder ...................... 13
MAINTENANCE
Cleaning and Metal Mesh Filter Care................. 14
Lights ................................................................................ 15
TROUBLESHOOTING................................................................ 16
LIST OF PARTS AND ACCESSORIES .............................. 17
1
Table of Contents
SAFETY NOTICE ................................................................. 2-3
LIST OF MATERIALS ....................................................... 4
www.zephyronline.com
Important Safety Notice
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE.
WARNING
TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer.
b. Before servicing or cleaning unit, switch power off at service panel and lock panel to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service
panel.
CAUTION
For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. Take care when using cleaning
agents or detergents. Suitable for use in household cooking area.
WARNING
TO REDUCE THE RISK OF RANGE TOP GREASE FIRE:
a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly
on low or medium settings.
b. Always turn hood ON when cooking at high heat or when aming food
c. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or lter.
d. Use proper pan size. Always use cookware appropriate for the size of the surface element.
e. Keep fan, lters and grease laden surfaces clean.
f. Use high setting on hood only when necessary.
g. Don’t leave hood unattended when cooking.
h. Always use cookware and utensils appropriate for the type of and amount of food being prepared.
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP FIRE, OBSERVE THE FOLLOWING:
a. SMOTHER FLAMES with a close- tting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.
If the ames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
b. NEVER PICK UP A FLAMING PAN – You may be burned.
c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.
d. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate it.
2. The re is small and contained in the area where it started.
3. The re department is being called.
4. You can ght the re with your back to an exit
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a. Installation work and electrical wiring must be done by quali ed person(s) in accordance with all applicable codes and standards.
Including re-rated construction.
b. Suf cient air is needed for power combustion and exhausting of gases through the ue (chimney) of fuel burning equipment to prevent
back-drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National
Fire Protection Association (NFPA) and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and
the local code authorities.
c. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
d. Ducted fans must always vent to the outdoors.
e. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFI
(Ground Fault Interrupter protected branch circuit).
g. NEVER place a switch where it can be reached from a tub or shower.
h. Make sure the power is off before installing, wiring or maintenancing.
2
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
CAUTION
To reduce risk of re and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings,
attics, crawl spaces or garages.
OPERATION
Always leave safety grilles and lters in place. Without these components, operating blowers could catch onto hair, ngers
and loose clothing.
The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,
maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to
negligence and the warranty of the unit automatically expires due to improper maintenance.
*NOTE: Please check www.zephyronline.com for revisions before doing any custom work.
ELECTRICAL REQUIREMENTS
Important:
Observe all governing codes and ordinances.
It is the customer’s responsibility:
- To contact a quali ed electrical installer.
- To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70
latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and
all local codes and ordinances.
If codes permit and a separate ground wire is used, it is recommended that a quali ed electrician determine that the
ground path is adequate.
Do not ground to a gas pipe.
Check with a quali ed electrician if you are not sure the range hood is properly grounded.
Do not have a fuse in the neutral or ground circuit.
*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269
** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575
This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit
protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to
Electrical Diagram on product.
A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, purchase
and install appropriate connector if necessary.
ZVE-E30AS - 420 Watts, 3.5 Amps
ZVE-E36AS - 520 Watts, 4.3 Amps
ZVE-E42AS - 520 Watts, 4.3 Amps
3
Important Safety Notice
WARNING
List of Materials
www.zephyronline.com
MODELS: ZVE-ExxAS
PARTS SUPPLIED
1 - Hood with internal blower
3 - Metal mesh filters (2 for ZVE-E30AS)
1 - Duct cover assembly (top and bottom)
1 - Duct cover wall bracket
4 - 50W GU-10 halogen light bulbs (2 for ZVE-E30AS)
1 - 6” round backdraft damper (pre-installed)
1 - Hardware package
HARDWARE PACKAGE CONTENTS
M4 x 3/8” (2)
Suction Cup (1)
M4 x 1-1/4” (3)
M4 x 1” (2)
Wire Nuts (3)
PARTS NOT SUPPLIED
- Ducting, conduit and all installation tools
- Cable connector (if required by local codes)
- Back splash accessory
- Wire spice rack accessory
- Duct cover extension accessory
- Recirculating kit accessory
4
Equivalent number
length x used
=
Duct pieces
Total
Total
3-1/ 4” x 10” 1 Ft.
Rect.,
straight
x(
) =
Ft.
6”- 8” Round 30 Ft.
wall cap
with damper
x(
) =
Ft.
7” Round,
straight
1 Ft.
x(
) =
Ft.
6”- 8” Round, 30 Ft.
roof cap
x(
) =
Ft.
8” Round,
straight
1 Ft.
x(
) =
Ft.
6” round to
1 Ft.
3-1/ 4” x 10”
rect.
transition
x(
) =
Ft.
3-1/ 4” x 10” 15 Ft.
Rect. 90 0
elbow
x(
) =
Ft.
x(
) =
Ft.
3-1/ 4” x 10” 9 Ft.
Rect. 45 0
elbow
x(
) =
Ft.
6” round to
16 Ft.
3-1/ 4” x 10”
rect.
transition
90 0 elbow
7” or 8”
Round,
90 0 elbow
15 Ft.
x(
) =
Ft.
3-1/ 4” x 10” 24 Ft.
Rect. 90 0
flat elbow
x(
7” or 8”
Round,
45 0 elbow
9 Ft.
x(
) =
Ft.
3-1/ 4” x 10” 30 Ft.
Rect.
wall cap
with damper
x(
7” or 8”
30 Ft.
Round
wall cap
with damper
x(
) =
Ft.
3-1/ 4” x 10” 5 Ft.
Rect. to
6” round
transition
x(
) =
Ft.
7” or 8”
Round,
roof cap
x(
) =
Ft.
3-1/ 4” x 10” 20 Ft.
Rect. to
6” round
transition
90 0 elbow
x(
) =
Ft.
7” round to
8 Ft.
3 1/ 4” x 10”
rect.
transition
x(
) =
Ft.
) =
Ft.
15 Ft.
x(
) =
Ft.
7” round to
23 Ft.
3-1/ 4” x 10”
rect.
transition
90 0 elbow
x(
6” Round,
90 0 elbow
6” Round,
45 0 elbow
9 Ft.
x(
) =
Ft.
Subtotal column 2 =
Ft.
Subtotal column 1 =
Ft.
Total ductwork
Ft.
) =
) =
Subtotal column 1 =
Ft.
Ft.
Ft.
Maximum Duct Length: For satisfactory air movement,
the total duct length of a 3 1/ 4” x 10” rectangular 6” or 7”
diameter round duct should not exceed 100 equivalent feet.
5
30 Ft.
=
Installation – Ducting Calculation Sheet
Equivalent number
length x used
=
Duct pieces
Installation – Mounting Height & Clearance
www.zephyronline.com
Minimum mount height between range top to hood
bottom should be no less than 28”.
min. ducted
min. recirc.
max.
min. 28”
max. 36”
Maximum mount height should be no higher than
36”.
32-1/2”
36“
51”
It is important to install the hood at the proper
mounting height. Hoods mounted too low could
result in heat damage and re hazard; while hoods
mounted too high will be hard to reach and will
loose its performance and ef ciency.
min. ducted 96”
min. recirc. 100”
max.
123”
If available, also refer to range manufacturer’s
height clearance requirements and recommended
hood mounting height above range. Always check
your local codes for any differences.
Minimum Mounting Height (Ducted)
8’. Hood mounted 28” above cooking surface;
64” from oor.
Minimum Mounting Height (Recirculating)
8’4”. Hood mounted 28” above cooking surface;
64” from oor.
Maxmimum Mounting Height
10’3”. Hood mounted 36” above cooking surface;
72” from oor.
36”
Note: Top duct cover with louver holes may be flipped upside down to hide louvers.
DUCTING
A minimum of 6” round or 3-1/4 x 10” rectangular
duct must be used to maintain maximum air ow
ef ciency.
Always use rigid type metal ducts only. Flexible
ducts could restrict air ow by up to 50%.
Use calculation worksheet to compute total duct
work.
ALWAYS, when possible, reduce the number of
transitions and turns. If a long duct run is required,
increase duct size from 6” to 7” or 8”.
If turns or transitions are required: Install as far
away from opening and as far apart, between 2,
as possible.
6
Duct cover extension kit available for ceiling
heights up to 14 feet. Turn to page 17 for part
number and ordering information.
DAMAGE-SHIPMENT / INSTALLATION:
• Please fully inspect unit for damage before
installation.
• If the unit is damaged in shipment, return the
unit to the store in which it was bought for
repair or replacement.
• If the unit is damaged by the customer, repair
or replacement is the responsibility of the
customer.
• If the unit is damaged by the installer (if other
than the customer), repair of replacement must
be made by arrangement between customer
and installer.
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages.
All exhaust must be ducted to the outside, unless using the recirculating option.
Use single wall rigid Metal ductwork only.
Fasten all connections with sheet metal screws and tape all joints w/ certi ed Silver Tape or Duct Tape.
Some Ducting Options
Roof Pitch w/
Flashing & Cap
side wall cap
w/ gravity damper
Soffit or crawl space
side wall cap
w/ gravity damper
ductless
recirculating
7
Installation – Ducting Options
WARNING FIRE HAZARD
Front of Hood
Side of Hood
14-5/16”
10”
1-5/8”
21-1/4”
10-5/8”
29-15/16”, 35-15/16”, 41-15/16”
24”
2”
ø5
7/
8”
8
electrical
k/o
1-1/4”
Top of Hood
4”
Installation – Hood Specifications
www.zephyronline.com
min. ducted 32-1/2””
min. recirc. 36”
max.
51”
C/L
1. Measure from range top to hood bottom and mark line A.
(28” minimum from range top) .
Duct Cover Bracket
2. Plum and mark center line.
9-7/16"
3. Mark mounting height line B. (10-3/8” from line A)
B
4. Mark mounting spread from C/L on line B. (9-7/16”)
5. Fasten (2) M4x1-1/4” screws into studs on line B. Do not
fasten screws all the way. note: wood blocking may
need to be added behind the drywall if no studs are
present. Wall anchors may also be used, check local
codes before using wall anchors.
10-3/8"
A
28" min
C/L
6. Hang hood onto screws and hand tighten. (Fig.A) Use
the last M4x1-1/4” screw to further secure the hood to
the wall from inside the hood.
7. Center and attach duct cover bracket to wall below
ceiling or sof t using (2) M4x1” screws.
8. Install electrical.
9. *Install duct work and duct tape.
10. Power up hood and check for leaks around duct tape.
11. Place telescopic duct covers onto hood and extend
inner (top) duct cover upwards and secure to duct cover
bracket using (2) M4x3/8” screws.
fig. A
*if using hood in recirculating mode you must secure air
diverter plate onto wall before installing duct work and
duct covers. Turn to page10 for more details.
! WARNING: Electrical wiring must be done by a qualified person(s) in
accordance with all applicable codes and standards. This range hood must be
properly grounded. Turn off electrical power at service entrance before wiring.
Cable Lock
A cable locking connector (not supplied) might
be required by local codes. Check with local
requirements and codes, purchase and install
appropriate connector if necessary.
Cable Lock
9
Installation – Mounting the Hood
! CAUTION: At least two installers are
required due to the weight and size of the
hood.
Installation – Ductless Recirculating
www.zephyronline.com
Ductless recirculating is intended for applications where an exhaust duct work is not possible to be installed.
When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust
from cooking are drawn and ltered by a set of optional charcoal lters. The air is then puri ed and recirculated back within the home.
We recommend to ALWAYS exhaust air outside of the home by employing existing or installing new duct
work, if possible. The hood is most effective and ef cient as an exhaust hood. Only when the exhaust option
is not possible should you recourse to converting the hood into a recirculating hood.
When converted to be a recirculating hood, a set of charcoal lters are required on top of its standard Metal
Filter set. Order according to its Part number below. The standard Metal Filters are intended to capture
residue from cooking and the optional charcoal lters help to purify fumes exhausted from cooking for recirculation.
RECIRCULATING KIT (REQUIRED IF NO DUCTING IS USED)
Kit includes charcoal lters and air diverter plate.
Hood Model
ZVE-E30AS
ZVE-E36AS/E42AS
Part No.
ZRC-0050
ZRC-0051
Filters in Pkg.
2
3
1. Secure air diverter plate to wall below duct cover wall bracket.
FIG.1 See manual included with recirculating kit for more
detailed instructions.
2. Remove metal mesh lters from hood. Clip charcoal lters
onto charcoal lter bracket built into hood. FIG.2
air diverter
plate
6" round duct
3. Re-install metal mesh lters.
4. Turn on charcoal lter change indicator on control panel. (refer
to details on page 12.) The microprocessor in the controls will
indicate the need to change the charcoal lter after 120 hours
of continuous use. Order replacement charcoal lters with per the
list below.
FIG.1
E
Charcoal Filter Replacements
Hood Model
ZVE-E30AS
ZVE-E36AS/E42AS
Part No.
Z0F-C022
Z0F-C022
Qty to Order
2
3
DO NOT WASH CHARCOAL FILTERS. Charcoal lters may need
to be changed more often depending on cooking habits.
Charcoal Filter Dimensions:
9in x 6 3/8in
228mm x 162mm
D
Install charcoal filter (plastic side exposed)
into filter bracket. Insert tab cut-out side D
of charcoal filter into bracket first. Lock
charcoal filter into place by pushing down
on side E with locking tabs.
FIG.2
10
Features & Controls - Touch Controls
Blower On/Off
Display (speed level, delay off, filter clean/change)
Lights On/Dim/Off
Adjust 6 Speed Levels
15 Min Delay Off
1. Blower On/Off
By pressing
the blower is switched on and off. When switched on, the blower starts up on speed level 3.
2. Speed Selection
The 6 speed levels are selected by pressing
selected.
to decrease and
to increase speed levels. The display indicates levels
3. Delay Off
of blower
the blowers
This feature is used for programmed shut down of
and lights 15 minutes after the function is activated. Press
once, a
dot flashes in the lower right side of display
indicating the function is on. The
will completely
shut down
after 15
The hood
blowers
will shut down
after 15
minutes.
4. Lights On/Dim/Off
Switch lights on by pressing
once, press a second time to dim and again to shut off lights.
5. Display Window
The display window indicates speed levels and features such as metal filter clean reminder, delay off and charcoal filter change
reminder.
Metal Filter Clean Reminder (metal mesh filter)
After every 30 hours of use the display will start flashing an A reminding you to clean the metal filters from residue and
possible clogs.
The standard metal mesh filters are required to be cleaned frequently and as recommended in order to maintain blower
efficiency. If improperly maintained, residue from cooking will sift through filters and cause damage to hood blowers and
other sensitive components; and possible clog duct work and create a fire hazard.
11
Features & Controls – Charcoal Filter Change Reminder
www.zephyronline.com
Charcoal Filter Change Reminder (charcoal filter, if installed)
When your hood is installed as a recirculating unit, it is fitted with a set of charcoal filters to purify exhaust
and fumes from cooking, then re-circulates the air within the home. These charcoal filters are required to
be replaced after every 120 hours of use. The charcoal filters should never be cleaned or placed in a dish
washer.
The filter change reminder function in the microprocessor needs to be switched on. When switched on, the
microprocessor will elapse and count usage time and indicate by a flashing C when charcoal filter
replacements are needed.
Setting the Filter Change Reminder
When off, hold
for approximately 5 seconds.
The display will change from
(exhaust mode) to
C (recirculating mode) this indicates that the
elapse timer function is switched on and charcoal
filters are used.
Filter Replace Indicator
When the display C starts flashing, the charcoal
filters need to be replaced.
Set Mode
hold 5 sec.
display from < - > to < C >
C
Set Mode
Change
FIlters
display < C > flashes
C
Re-setting Function
Once filters are replaced, with hood off, press and
hold
the display will appear; hold for apprimately
5 seconds until C on displays disappears
.
The filter change reminder is now re-set and a new
120 hour elapse cycle is initiated.
12
To Reset
hold 5 sec.
display from < C > to < >
C
Metal Filter Clean Indicator
When A flashes on display, the metal filters
installed are required to be cleaned. This will occur
after every 30 hours of use.
Clean Filters
display < A > flashes
A
Re-setting Function
Reset the filter clean reminder timer when filters are
cleaned and re-installed (with hood off). Press and
hold
for approximately 5 seconds, the display will
appear; hold for approximately 5 seconds until A on
display disappears
. The filter clean reminder
function is now reset and a new 30 hours elapse
cycle is initiated.
To Reset
hold 5 sec. display from < A > to < >
A
13
Features & Controls – Metal Mesh Filter Clean Reminder
Metal Filter Clean Reminder (metal mesh filter)
Whether your hood is installed as an exhaust or purifying unit, a set if metal mesh filters are fitted by the
factory, These metal mesh filters are intended to filter out residue from cooking. They need not be
replaced on a regular basis but are required to be kept clean. The filter clean reminder function in the
microprocessor will automatically indicate by a flashing A when the metal mesh filters need to be
cleaned after every 30 hours of use. Filters can be cleaned by hand with non-abrasive soap or in a
dishwasher. Heavily soiled filters should also be soaked in grease cutting detergent prior to cleaning.
Maintenance – Cleaning and Metal Mesh Filter Care
www.zephyronline.com
SURFACE MAINTENANCE:
Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent ,
or steel wool/scouring pads which will scratch and damage surface.
For heavier soil use liquid degreaser.
After cleaning it is recommended that you use non-abrasive stainless steel polish/cleaners, to polish and
buff out the stainless luster and grain. Always scrub lightly, with clean cotton cloth, and with the grain.
Do not use any product containing chlorine bleach. Do not use “orange” cleaners.
Metal Mesh Filters
The metal mesh lters installed by the factory are intended to lter out residue and grease from cooking.
They need not be replaced on a regular basis but are required to be kept clean.
Filters should be cleaned after every 30 hours of use or once a month.
Remove and clean by hand or in dishwasher on low heat. Spray degreasing detergent and leave to soak if
heavily soiled.
Dry lters and re-install before using hood.
Removing Metal Mesh Filters
1. Push in on spring loaded handle
2. Pull down on lter hande to remove lter
Should lters wear out due to age and prolonged use,
replace with following part number:
Hood Model:
ZVE-E30AS
ZVE-E36AS/E42AS
Part No.
50200004
50200004
Qty. to Order.
2
3
Metal Mesh Filter Dimensions:
16 1/8in. x 9 1/8in.
409mm x 232mm
14
CAUTION: Light bulb becomes extremely hot when turned on.
DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns.
Make sure all power is turned off and bulbs are not hot.
Remove by turning bulb counter clockwise. Note: Bulb does not unscrew; it turns 60 degrees,
stops and falls out.
If bulbs are dif cult to turn due to prolonged use, rmly attach a glass suction cup approximately the diameter of
the bulb or use a rubber/latex glove and turn counter clockwise.
Replacement bulbs are available at specialty lighting stores. Purchase type MR16 (GU-10) 50W halogen.
For Zephyr part numbers please turn to page 17 of the manual.
15
Maintenance - Lights
REPLACING LIGHT BULBS
Troubleshooting
www.zephyronline.com
TROUBLESHOOTING PROCEDURES FOR VENEZIA
Issue
Cause
What to do
After installation,
the unit doesn’t
work.
1. The power source is not turned ON.
1. Make sure the circuit breaker and the unit’s
power is ON.
2. The power line and the cable locking connector
is not connecting properly.
2. Check the power connection with the unit is
connected properly.
3. The switch board and control board wirings are
disconnected.
3. Make sure the wirings between the switch
board and control board are connected
properly.
4. The switch board or control board is defective.
4. Change the switch board or control board.
1. The motor is defective, possibly seized.
1. Change the motor.
2. The thermally protected system detects if the
motor is too hot to operate and shuts the motor
down.
2. The motor will function properly after the
thermally protected system cool down.
3. Damaged capacitor.
3. Change the capacitor.
4. The switch board or control board is defective.
4. Change defective part.
1. The motor is not secure in place.
1. Tighten the motor in place.
2. Damaged blower wheel.
2. Replace the blower.
Light works,
but motor is not
turning.
The unit is
vibrating.
3. The hood is not secured in place.
3. Check the installation of the hood.
4. The switch board or control board is defective.
4. Change defective part.
The motor is
working, but the
lights are not.
1. Defective halogen bulb.
1. Change the halogen bulb.
2. The light bulb is loose.
2. Tighten the light bulb.
The hood is
not venting out
properly.
1. The hood might be hanging to high from the
cook top.
1. Adjust the distance between the cook top and
the bottom of the hood within 28” and 36”
range.
2. The wind from the opened windows or opened
doors in the surrounding area are affecting the
ventilation of the hood.
2. Close all the windows and doors to eliminate
the outside wind ow.
3. Blockage in the duct opening or ductwork.
3. Remove all the blocking from the duct work or
duct opening.
4. The direction of duct opening is against the wind.
4. Adjust the duct opening direction.
5. Using the wrong size of ducting.
5. Change the ducting to at least 6” or higher
for the internal blower and 8” or higher for the
external blower.
1. Metal lter is loose.
1. Change the metal lter.
Metal Filter is
vibrating.
16
PART#
Replacement Parts
Light Bulb MR16 (GU10) 50W (each)
Metal Mesh Filter (each)
Z0B0020S
50200004
Optional Accessories
Recirculating Kit, ZVE-E30AS
Recirculating Kit, ZVE-E36AS/E42AS
Replacement Charcoal Filter (each)
Duct Cover Extension Kit
ZRC-0050
ZRC-0051
Z0F-C002
Z1C-00VE
To order parts, visit us online at http://store.zephyronline.com or call us at 1.888.880.8368
17
List of Parts & Accessories
DESCRIPTION
STAPLE YOUR RECEIPT HERE
Proof of the original purchase
date is needed to obtain
service under warranty
Limited Warranty
TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call:
1-888-880-8368
Zephyr Corporation (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein
as “you” or “your”) of Zephyr products (the “Products”) that such Products will be free from defects in materials or workmanship as follows:
Two Year Limited Warranty for Parts: For two years from the date of your original purchase of the Products, we will
provide, free of charge, Products or parts to replace those that failed due to manufacturing defects. We may choose, in
our sole discretion, to repair or replace parts before we elect to replace the Products.
One Year Limited Warranty for Labor: For one year from the date of your original purchase of the Products, we will
provide, free of charge, the labor cost associated with repairing the Products or parts to replace those that failed due to
manufacturing defects. After the first year from the date of your original purchase, you are responsible for all labor costs
associated with this warranty.
Warranty Exclusions: This warranty covers only repair or replacement, at our option, of defective Products or parts
and does not cover any other costs related to the Products including but not limited to: (a) normal maintenance and
service required for the Products and consumable parts such as light bulbs, metal and carbon filters and fuses; (b) any
Products or parts which have been subject to freight damage, misuse, negligence, accident, faulty installation or installation contrary to recommended installation instructions, improper maintenance or repair (other than by us); (c) commercial use of the Products or use otherwise inconsistent with its intended purpose; (d) natural wear of the finish of the Products or wear caused by improper maintenance, use of corrosive and abrasive cleaning products, pads, and oven cleaner
products; (e) chips, dents or cracks caused by abuse or misuse of the Products; (f) service trips to your home to teach
you how to use the Products; or (g) damage to the Products caused by accident, fire, floods or act of God. If you are
outside our service area, additional charges may apply for shipping costs for warranty repair at our designated service
locations and for the travel cost to have a service technician come to your home to repair, remove or reinstall the Products. After the first year from the date of your original purchase, you are also responsible for all labor costs associated
with this warranty.
Limitations of Warranty. OUR OBLIGATION TO REPAIR OR REPLACE, AT OUR OPTION, SHALL BE YOUR SOLE
AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. WE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF
THE PRODUCTS. THE EXPRESS WARRANTIES IN THE PRECEDING SECTION ARE EXCLUSIVE AND IN LIEU OF
ALL OTHER EXPRESS WARRANTIES. WE HEREBY DISCLAIM AND EXCLUDE ALL OTHER EXPRESS WARRANTIES FOR THE PRODUCTS, AND DISCLAIM AND EXCLUDE ALL WARRANTIES IMPLIED BY LAW, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states or provinces do not
allow limitations on the duration of an implied warranty or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. To the extent that applicable law prohibits the exclusion of implied warranties, the duration of any applicable implied warranty is limited to the same two-year period
described above. Any oral or written description of the Products is for the sole purpose of identifying the Products and
shall not be construed as an express warranty. Prior to using, implementing or permitting use of the Products, you shall
determine the suitability of the Products for the intended use, and you shall assume all risk and liability whatsoever in
connection with such determination. We reserve the right to use functionally equivalent refurbished or reconditioned
parts or Products as warranty replacements or as part of warranty service. This warranty is not transferable from the
original purchaser and applies in the United States and Canada.
To Obtain Service Under Limited Warranty: To qualify for warranty service, you must: (a) notify us at the address or
telephone number stated below within 60 days of the discovery of the defect; (b) give the model number and part identification number and serial number; and (c) describe the nature of any defect in the Product or part. At the time of the
request for warranty service, you must present evidence of your proof of purchase and proof of the original purchase
date. If we determine that the warranty exclusions listed above apply or if you fail to provide the necessary documentation to obtain service, you will be responsible for all shipping, travel, labor and other costs related to the services.
Please check our website for any revisions, www.zephyronline.com.
Zephyr Corporation Service Department, 2277 Harbor Bay Parkway, Alameda, CA 94502 1-888-880-8368
JUN08.0101
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising