ViewSonic | VS11419 | Service manual | ViewSonic VS11419 Service manual

ViewSonic VS11419 Service manual
Service Manual
ViewSonic VG1930wm-3
Model No. VS11419
19” Color TFT LCD Display
(VG1930wm-3_SM Rev. 1a Jan. 2007)
ViewSonic 381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583
Copyright
Copyright © 2007 by ViewSonic Corporation. All rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, electronic, mechanical, magnetic,
optical, chemical, manual or otherwise, without the prior written permission of ViewSonic
Corporation.
Disclaimer
ViewSonic makes no representations or warranties, either expressed or implied, with respect to
the contents hereof and specifically disclaims any warranty of merchantability or fitness for any
particular purpose. Further, ViewSonic reserves the right to revise this publication and to make
changes from time to time in the contents hereof without obligation of ViewSonic to notify any
person of such revision or changes.
Trademarks
Optiquest is a registered trademark of ViewSonic Corporation.
ViewSonic is a registered trademark of ViewSonic Corporation.
All other trademarks used within this document are the property of their respective owners.
Revision History
Revision
SM Editing Date
1a
1/12/2007
ViewSonic Corporation
ECR Number
Description of Changes
Initial Release
Editor
Jamie Chang
i
Confidential - Do Not Copy
VG1930wm-3
TABLE OF CONTENTS
1.
Precautions and Safety Notices
1
2.
Specification
5
3.
Front Panel Function Control Description
15
4.
Circuit Description
21
5.
Adjusting Procedure
28
6.
Trouble Shooting Flow Chart
64
7.
Block Diagrams
72
8.
Schematic Diagrams
73
9.
PCB Layout Diagrams
78
10. Exploded Diagram And Spare Parts List
84
11. Recommended Spare Parts List
86
ViewSonic Corporation
ii
Confidential - Do Not Copy
VG1930wm-3
1. Precautions and Safety Notices
1. Appropriate Operation
(1) Turn off the product before cleaning.
(2) Use only a dry soft cloth when cleaning the LCD panel surface.
(3) Use a soft cloth soaked with mild detergent to clean the display housing.
(4) Use only a high quality, safety approved AC/DC power cord.
(5) Disconnect the power plug from the AC outlet if the product will not be used for a long period of time.
(6) If smoke, abnormal noise, or strange odor is present, immediately switch the LCD display off.
(7) Do not touch the LCD panel surface with sharp or hard objects.
(8) Do not place heavy objects on the LCD display, video cable, or power cord.
(9) Do not use abrasive cleaners, waxes or solvents for your cleaning.
(10) Do not operate the product under the following conditions:
-
Extremely hot, cold or humid environment.
-
Areas containing excessive dust and dirt.
-
Near any appliance generating a strong magnetic field.
-
In direct sunlight.
2. Caution
No modification of any circuit should be attempted. Service work should only be performed after you are thoroughly
familiar with all of the following safety checks and servicing guidelines.
3. Safety Check
Care should be taken while servicing this LCD display. Because of the high voltage used in the inverter circuit, the voltage is
exposed in such areas as the associated transformer circuits.
4. LCD Module Handling Precautions
4.1 Handling Precautions
(1) Since front polarizer is easily damaged, pay attention not to scratch it.
(2) Be sure to turn off power supply when connecting or disconnecting input connector.
(3) Wipe off water drops immediately. Long contact with water may cause discoloration or spots.
(4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
(5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
(6) Since CMOS LSI is used in this module, take care of static electricity and ensure human earth when handling.
(7) Do not open or modify the Module Assembly.
(8) Do not press the reflector sheet at the back of the module in any direction.
(9) In the event that a Module must be put back into the packing container slot after it was taken out of the container, do
not press the center of the CCFL Reflector edge. Instead, press at the far ends of the CFL Reflector edge softly.
Otherwise the TFT Module may be damaged.
(10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate or tilt the Interface Connector of
the TFT Module.
(11) After installation of the TFT Module into an enclosure (LCD monitor housing, for example), do not twist or bend the
TFT Module even momentarily. When designing the enclosure, it should be taken into consideration that no
ViewSonic Corporation
1
Confidential - Do Not Copy
VG1930wm-3
bending/twisting forces may be applied to the TFT Module from outside. Otherwise the TFT Module may be
damaged.
(12) The cold cathode fluorescent lamp in the LCD contains a small amount of mercury. Please follow local ordinances
or regulations for disposal.
(13) The LCD module contains a small amount of materials having no flammability grade. The LCD module should be
supplied with power that complies with the requirements of Limited Power Source (IEC60950 or UL1950), or an
exemption should be applied for.
(14) The LCD module is designed so that the CCFL in it is supplied by a Limited Current Circuit (IEC60950 or
UL1950). Do not connect the CCFL to a Hazardous Voltage Circuit
ViewSonic Corporation
2
Confidential - Do Not Copy
VG1930wm-3
Correct methods :
Incorrect Methods :
Only touch the metal-frame of the panel or the front
Surface of the panel is pressed by fingers & this may
cover of the monitor.
cause “ MURA “
Do not touch the surface of the polarizer .
Take out the monitor by grasping the LCD panel.
Take out the monitor form carton.
ViewSonic Corporation
That may cause “ MURA“.
3
Confidential - Do Not Copy
VG1930wm-3
Correct methods :
Incorrect Methods :
Place the monitor on a clean & soft foam pad .
Place the monitor on foreign objects .
That could scratch the surface of panel
ViewSonic Corporation
4
Confidential - Do Not Copy
VG1930wm-3
2. Specification
Introductions
FEATURES
TFTLCD PANEL
Input Signal
Sync Compatibility
Compatibility
Power Voltage
Power Consumption
Audio
Ergonomics
OSD Control
VG1930wm-3
Size
19 “W
Luminance (Typ)
300 cd/㎡
Contrast Ratio (Typ)
700:1
Colors
16.2 M colors
Response Time (Typ)
5 ms
Viewing Angle (H/V)
150/130(degrees;type)@CR>10
Recommend resolution
1440 X 900 @60Hz
Analog (75ohms, 0.7/1.0 Vp-p)
Yes
Digital
Yes
Separate Sync
Yes
Composite Sync
Yes
Sync on Green
Yes
PC
Yes
Power Mac
Yes
TV Box (NextVision 6)
No
AC 100-240V, 50/60Hz
Yes
On Mode(Max / Typ)
36 W
Active Off Mode (Max)
<2 W
W
1.5w X 2
Tilt
-5 ° ~ 20 °
Swivel ( -xx ° - xx °)
360
Pivot ( XX ° - XX °)
No
Height Adjust ( XX-XX mm)
0-80mm
[ ] [ 1 ] [ 2 ] [▲] [▼] [; X]
Yes
460 mm (W) x 434 mm (H) x 230 mm (D)
Physical (W x H x D)
18.1" (W) x 17.1" (H) x 9.1" (D)
Dimension
560 mm (W) x 525 mm (H) x 282 mm (D)
Package (W x H x D)
Weight
Operating Condition
Storage Condition
22" (W) x 20.7" (H) x 11.1" (D)
Physical (lbs / Kg)
5.5 Kg (12.13 lbs)
Package (lbs / Kg)
7.3 Kg (16.10 lbs)
Temperature (℉/℃)
32°F to 104°F (0°C to 40°C)
Humidity (%)
10% to 90% (no condensation)
Temperature (℉/℃)
-4°F to 140°F (-20°C to 60°C) Humidity (%)
10% to 90% (no condensation)
UL, CUL, FCC-B (ICES), CB, CE, TCO'03, ICES-003B, ISO13406-2, TUV/GS, TUV ERGO(covers ISO13406-2 &
Regulation
MPRII), TUV-S, VCCI, NOM, GOST-R, HYGIENIC (20 copies), ENERGY, Energy Star, CCC, BSMI, PSB,
C-TICK, KTL/MIC, SASO, WEEE, RoHS
ViewSonic Corporation
5
Confidential - Do Not Copy
VG1930wm-3
Product definition and specification
Product Name
ViewSonic VG1930wm
Oracle P/N
VG1930WM-3
Model Number
OSD Languages
VS11419
English, French, German, Italian, Spanish,
Finnish, Japanese, Traditional Chinese,
Simplified Chinese
TFT LCD Panel and Model #
CMO M190A1-L02
Scalar
MST TSUM56AL-LF-1
Input Signal
Analog x1 / Digital x1
Sync Compatibility
Separate Sync / Composite Sync / SOG
Adapter
Internal Power Board
Yes,
refer to APPENDIX B: Power Cable
Power Cable
Analog Cable (1.8 m, black), with PC 2001 and
Yes
Hot Plug Detect &DDC
(Detached cable; refer the Appendix A)
DVI-D Cable(1.8m, black) with PC 2001
For Region code = P/A/J/K/S units only
Audio Cable(1.8m, black) with PC 2001
Yes
MIC Cable(1.8m, black) with PC 2001
No
USB Cable (V2.0)
No
ViewSonic CD Wizard
ViewSonic
Quick Start Guide
Arabic, English, Finnish, Spanish,
German, Italian, Japanese, Swedish,
Polish, Korean, Portuguese, Russian,
Turkish , French, Czech, Hungarian,
Simplified Chinese, Traditional Chinese
PerfectSuite CD
No
Screen Protector Mylar
Yes
Foot Protector plastic
No
Service Insert
For Region code = M units only
Warranty Sticker
For Region code = G units only
Warranty Card
For Region code = G units only
Carton Sticker
For Region code = G units only
PE bag of Carton
For Region code = G units only
ViewSonic Corporation
6
Confidential - Do Not Copy
VG1930wm-3
2.2 GENERAL specification
Test Resolution & Frequency
“1440 X900” @ 60Hz
Test Image Size
Full Size
Contrast and Brightness Controls
Factory Default:
Contrast = 70%, Brightness = 100%
2.3 VIDEO INTERFACE
Input Connector(refer the appendix A)
Analog : D-sub 15 ,
Digital: DVI-D
Default Input Connector
Defaults to the first detected input
Video Cable Strain Relief
Equal to twice the weight of the monitor for five
minutes
Video Cable Connector DB-15 Pin out
Refer to Appendix A; Compliant DDC/CI
Video Signals
Video RGB (Analog)
Separate Sync / Composite Sync / SOG
TMDS (Digital)
Video Impedance
75 Ohms (Analog), 100 Ohms (Digital)
Maximum PC Video Signal
950 mV with no damage to monitor
Maximum Mac Video Signal
1250 mV with no damage to monitor
Sync Signals
TTL
DDC 1/2B
Compliant with version 1.1
Sync Compatibility
Separate Sync / Composite Sync / SOG
Video Compatibility
Shall be compatible with all PC type computers,
Macintosh computers, and after market video cards
Resolution Compatibility
Refer to Segment 4-5
Exclusions
Not compatible with interlaced video
2.4 POWER SUPPLY
Internal Power Supply
Mirage 860-AB0-190DTLB-PVH
Input Voltage Range
90 to 264 VAC
Input Frequency Range
47 to 63 Hertz
Short Circuit Protection
Output can be shorted without damage
Over Current Protection
5A typical at 14.0 VDC
Leakage Current
3.5mA (Max) at 254VAC / 60Hz
Efficiency(at 115VAC Full Load)
Typical: 80%
Fuse
Minimum: 75%
Internal and not user replaceable
Power Dissipation
39 Watts (typ) / 49.2W (max)
Max Input AC Current
1.5 Arms @ 90VAC, 0.75 Arms @180VAC
Inrush Current (Cold Start)
50 A (max) @ 115VAC
90 A (max) @ 230VAC
ViewSonic Corporation
7
Confidential - Do Not Copy
VG1930wm-3
Power Supply Cold Start
Power Supply Transient Immunity
Shall start and function properly when under full load, with all
combinations of input voltage, input frequency, and operating
temperature.
Shall be able to withstand an ANSI/IEEE C62.41-1980 6000V 200
ampere ring wave transient test with no damage.
Power Supply Line Surge Immunity
Shall be able to withstand 1.5 times nominal line
voltage for one cycle with no damage.
Power Supply Missing Cycle Immunity
Shall be able to function properly, without reset or
visible screen artifacts, when ½ cycle of AC power is
randomly missing at nominal input.
Power Supply Acoustics
The power supply shall not produce audible noise that
would be detectable by the user. Audible shall
defined to be in compliance with ISO 7779 (DIN
EN27779:1991) Noise measurements of machines
acoustics. Power Switch noise shall not be
considered.
Power Saving Operation(Method)
VESA DPMS Signaling
Mode
Power Consumption
Recovery Time
ViewSonic Corporation
LED
Power
Consumption
On
Blue
34W (typ)
36W (max)
Active off
Amber
<2W
Off
Off
<1W
ON Mode = N/A, ACTIVE OFF < 3 sec
8
Confidential - Do Not Copy
VG1930wm-3
2.5 ELECTRICAL REQUIREMENT
Horizontal / Vertical Frequency
Horizontal Frequency
30 – 82 kHz
Vertical Refresh Rate
56– 76 Hz.
Maximum Pixel Clock
135 MHz
Sync Polarity
Independent of sync polarity
Timing Table
Separated
Composite
SOG
Digital - TMDS
Analog
1
640 x 350
@
70 Hz,
31.5 KHz
DMT
2
640 x 400
@
60 Hz,
31.5 KHz
3
640 x 400
@
70 Hz,
31.5 KHz
4
640 x 480
@
50 Hz,
24.7 KHz
5
640 x 480
@
60 Hz,
31.5 KHz
6
640 x 480
@
67 Hz,
7
640 x 480
@
8
640 x 480
9
Item
Timing
DMT
KHz
For MAC
72 Hz,
37.9 KHz
DMT
@
75 Hz,
37.5 KHz
DMT
720 x 400
@
70 Hz,
31.5 KHz
10
720 x 480
@
60 Hz,
31.5 KHz
DTV
11
720 x 576
@
50 Hz,
31.3 KHz
DTV
12
800 x 600
@
56 Hz,
35.1 KHz
DMT
13
800 x 600
@
60 Hz,
37.9 KHz
DMT
14
800 x 600
@
72 Hz,
48.1 KHz
DMT
15
800 x 600
@
75 Hz,
46.9 KHz
DMT
16
832 x 624
@
75 Hz,
49.7 KHz
MAC
17
1024 x 768
@
60 Hz,
48.4 KHz
DMT
18
1024 x 768
@
70 Hz,
56.5 KHz
DMT
19
1024 x 768
@
75 Hz,
KHz
DMT
20
1152 x 864
@
75 Hz,
67.5 KHz
DMT
21
1152 x 870
@
75 Hz,
68.7 KHz
For MAC
22
1152 x 900
@
67 Hz,
62.5 KHz
For SUN
23
1280 x 720
@
50 Hz,
37.5 KHz
24
1280 x 720
@
60 Hz,
25
1280 x 768
@
60 Hz,
47.8 KHz
DMT;
26
1280 x 768
@
75 Hz,
60.3 KHz
DMT;
27
1280 x 960
@
60 Hz,
59.7 KHz
DMT
28
1280 x 960
@
75 Hz,
75.2 KHz
ViewSonic Corporation
35
60
45
Remark
DTV
KHz
DTV
9
Confidential - Do Not Copy
VG1930wm-3
29
1280 x 1024
@
60 Hz,
64
KHz
DMT
30
1280 x 1024
@
75 Hz,
80
KHz
DMT
31
1440 x 900
@
60 Hz
55.9 KHz
DMT
*1. Tolerance ≧ ±2KHz (if no overlapping issue)
*2. Any timing not in the list, it should display as normal or show on “OUT OF RANGE” OSD message without
blanking.
*3. The image quality of 50Hz mode might be worse than 60Hz.
Primary Presets
1440x900 @ 60Hz
User Presets
Number of User Presets (recognized timings) Available: 10 presets total in FIFO configuration
Changing Modes
● Maximum Mode Change Blank Time for image stability : 5 seconds (Max), excluding “Auto
Adjust” time
● Under DOS mode (640 x 350, 720 x 400 & 640 x 400),
execute “Auto Adjust”
it should recall factory setting when
● The monitor needs to do “Auto Adjust” the first time a new mode is detected
(see section “0-Touch™ Function Actions”)
● While running Change Mode, Auto Adjust or Memory Recall, the image shall blank
ViewSonic Corporation
10
Confidential - Do Not Copy
VG1930wm-3
2.6 FRONT PANEL CONTROLS AND INDICATORS
Front Panel Hardware Controls
Power Switch (Front Head)
Power Control, soft Power Switch.
Power LED (Front Head)
Blue – ON
Orange – Power Saving Mode
Dark = Soft Power Switch OFF
Front Panel Controls (Head)
;X] Mute
[ ] Power
[ 1 ] BUTTON 1
[ 2 ] Button 2
[▲] UP ARROW BUTTON
[▼] DOWN ARROW BUTTON
[;X] [ 1 ] [▲]
[▼] [ 2 ] [ ]
Note: Power Button, Button 1 and Button 2 must be
one-shot logic operation. (i.e. there should be no
cycling)
OSD must fully appear within 0.5s after pushing Button
1
Reaction Time
Short Cuts Function from the button(s)
[2]
Input toggle (Analog or Digital; refer to Appendix D)
[▼] or [▲]
Brightness/Contrast adjust
[▼]+ [▲]
recall both of Contrast and Brightness to default
[1] + [2]
toggle 720x400 and 640x400 mode when input 720x400 or
640x400 mode (70Hz only)
[1] + [▼] + [▲]
White Balance. (Not shown on user’s guide)
[1] + [▼]
Power Lock
[1] + [▲]
OSD Lock
No signal + [2] + [ ]
Burning mode
Signal + [2] + [ ]
Factory Mode
Remark : All the short cuts function are only available while OSD off
Function descriptions
Main Menu Controls
The Main Menu OSD includes most of control functions.
Please refer to APPENDIX C (Main Menu OSD Table) for the detail.
OSD Lock short cuts function for the buttons
The OSD lock will be activated by pressing the front panel control buttons "(1), & (▲)"
for 10 seconds. If the user then tries to access the OSD by pressing any of the buttons
"1", "▼", "▲", "2" a message will appear on the screen for 3 seconds showing "OSD
Locked". The OSD lock will be deactivated by pressing the front panel control buttons
ViewSonic Corporation
11
Confidential - Do Not Copy
VG1930wm-3
"(1), & (▲)" again for 10 seconds.
Note1: When the OSD is locked will lock all functions, including “Volume” and “Mute”
Note 2: Status bar indicating OSD Lock or Unlock is in progress and when complete
it will indicate “OSD Locked”
Note 3: OSD Lock should not lock Power Button and Power Lock function
Power Lock short cuts function for the buttons
The power button lock will be activated by pressing the front panel control buttons "(1),
& (▼)" for 10 seconds. Locking the power button means that the user won't be able to
turn off the LCD while the power button is locked. If the user presses the power button
while it is locked, a message will appear on the screen for 3 seconds showing "Power
Button Locked". It also means that with the power button locked, the LCD would
automatically turn back "On" when power is restored after a power failure. If the power
button is not in the locked mode, then power should return to it's previous state when
power is restored after a power failure. The power button lock will be deactivated by
pressing the front panel control buttons "(1), & (▼)" again for 10 seconds.
Note 1: Status bar indicating Power Button lock or unlock is in progress and when
complete it will indicate “Power Button Locked”
Note 2: Power should only be lockable in the “On State”
Memory Recall Actions
Memory Recall action on the analog and digital mode as below
1. Recall white balance to factory setting
2. Set the factory defaults as shown in Section 4-8
3. Clean all the mode setting buffer
4. Execute Auto Image Adjust
Note: Memory Recall should have no effect for Language, Power Lock, User Color
Settings or Input Priority
Input Signal Notice Actions
1. The Input Signal Notice OSD appears 3 seconds when power turns on or change
input signal.
2. The Input Signal Notice OSD position is on the right-bottom side of image. And the
OSD background shall be transparent. (OSD Background = off).
Resolution Notice Actions
1. Resolution Notice OSD should show on screen after changing to non-native mode
for 30 sec
2. For auto input select function, it shall meet the requirement in Appendix D.
3. The OSD should disappear after 10 sec or by pushing button [1] or [2]
Resolution Notice function should be disabled when push button [2] under Resolution
Notice OSD
ViewSonic Corporation
12
Confidential - Do Not Copy
VG1930wm-3
0-Touch™ Function Actions
1. Execute Auto Image Adjust when new mode detected, and save the settings to
buffer for further use
2. It should be reset by Memory Recall function
(Should not reset by power off, power unplug and others)
OSD Auto Save
The OSD shall save new settings when it is turned off by the user or when it times out.
There shall not be a separate save
Factory Defaults
Item
Defaults
Item
Defaults
Contrast
70%
Input Priority
N/A
Brightness
100%
Resolution Notice
On
Color Temperature
6500K
Volume
50%
Sharpness
100%
Balance
N/A
OSD H. Position
50%
Treble
N/A
OSD V. Position
50%
Bass
N/A
OSD Time Out
15
720x400 / 640x400
720x400
OSD Background
On
2.7 AUDIO INTERFACE (SPEAKER SPECIFICATION)
Line input connection
3.5 mm stereo jack
Line input signal
1.0 Vrms
Line input impedance
10 kOhm
Maximum power output (Electric)
1.5 W / ch
Signal to Noise Ratio
50 dB
Frequency response
100 Hz – 20 Khz
Distortion
< 10 % THD (@1kHz)
Vibration
Screen image
There should be no audible vibration with volume at 100% and
treble / bass at default.
There should be no affect on the screen image stability under any
conditions.
Connector PC99 requirement Audio in
Lime Green pantone # 577C
Cable type / length
3.5mm stereo cable / 1.8m length
Audio DPMS
Speakers should be off when the rest of the monitor is in power
saving.
* No any sympathetic or abnormal noise allowed.
ViewSonic Corporation
13
Confidential - Do Not Copy
VG1930wm-3
TFT LCD PANEL
1st Source Panel
Model number
CMO M190A1-L02
Type
Active Matrix TFT, TN technology
Active Size
19” Wide (410.4mm x 256.5mm)
Pixel Arrangement
RGB Vertical Stripe
Pixel Pitch
0.285 mm
Glass Treatment
Anti-Glare, Hard coating (3H)
# of Backlights
4 CCFL
Backlight Life
40000 Hrs (Min)
Luminance (Center) –
300 cd/m2 (Typ after 30 minute warm up)
CT = 6500K,
230 cd/m2 (Min after 30 minute warm up)
Contrast/ Brightness = Max
Brightness Uniformity (13 points)
77 % (Typ) / 67 % (Min)
Contrast Ratio
700 :1 (Typ)
500 : 1 (Min)
Color Depth
16.2 million colors (6+2 bit panel)
Horizontal Viewing Angle
150 degrees (Typ) / 130 degrees (Min) @ CR>10
Vertical Viewing Angle
130 degrees (Typ) / 120 degrees (Min) @ CR>10
Response Time
10%-90% @ Ta=25°C
On-Off
5ms (Typ) / 15ms (Max)
Mercury
3.0 mg per lamp
Panel Defects
Please see Panel Quality Specifications.
ViewSonic Corporation
14
Confidential - Do Not Copy
VG1930wm-3
3. Front Panel Function Control Description
Adjusting the Screen Image
Main Menu
with OSD controls
Front Control Panel
shown below in detail
Standby Power On/Off
Power light
Blue = ON
Orange = Power Saving
Audio Mute button turns the sound off
Displays the Main Menu or exits the control screen and saves
adjustments.
Scrolls through menu options and adjusts the displayed control.
Also a shortcut to display the Contrast adjustment control screen.
Displays the control screen for the highlighted control.
Also toggles between two controls on some screens.
Also a shortcut to toggle analog and digital connection.
ViewSonic Corporation
15
Confidential - Do Not Copy
VG1930wm-3
Do the following to adjust the display setting:
1. To display the Main Menu, press button [1].
NOTE: All OSD menus and adjustment screens disappear automatically after about 15
seconds. This is adjustable through the OSD timeout setting in the setup menu.
2. To select a control to adjust, pressSorTto scroll up or down in the Main Menu.
3. After the desired control is selected, press button [2]. A control screen like the one shown
below appears.
The command line at the bottom of the
control screen tells what to do next from
this screen. You can toggle between control
screens, adjust the selected option, or exit
the screen.
4. To adjust the setting, press the up S or down T buttons.
5. To save the adjustments and exit the menu, press button [1] twice.
The following tips may help you optimize your display:
• Adjust the computer's graphics card so that it outputs a 1440 x 900 @ 60Hz video signal to
the LCD display. (Look for instructions on “changing the refresh rate” in the graphics card's
user guide.)
• If necessary, make small adjustments using H. POSITION and V. POSITION until the
screen image is completely visible. (The black border around the edge of the screen should
barely touch the illuminated “active area” of the LCD display.)
ViewSonic Corporation
16
Confidential - Do Not Copy
VG1930wm-3
Main Menu Controls
Adjust the menu items shown below by using the up S and down T buttons.
Control
Explanation
Auto Image Adjust sizes and centers the screen image automatically.
Contrast adjusts the difference between the image background (black level)
and the foreground (white level).
Brightness adjusts background black level of the screen image.
Input Select toggles between inputs if you have more than one computer
connected to the VG1930wm.
Audio Adjust
Volume increases the volume, decreases the volume, and mutes the audio.
Mute temporarily silences audio output.
Color Adjust provides several color adjustment modes, including preset color
temperatures and a User Color mode which allows independent adjustment of
red (R), green (G), and blue (B). The factory setting for this product is 6500K
(6500 Kelvin).
sRGB-This is quickly becoming the industry standard for color management,
with support being included in many of the latest applications. Enabling this
setting allows the LCD display to more accurately display colors the way they
were originally intended. Enabling the sRGB setting will cause the Contrast and
Brightness adjustments to be disabled.
ViewSonic Corporation
17
Confidential - Do Not Copy
VG1930wm-3
Control
Explanation
9300K-Adds blue to the screen image for cooler white (used in most office
settings with fluorescent lighting).
6500K-Adds red to the screen image for warmer white and richer red.
5400K-Adds green to the screen image for a darker color.
5000K-Adds blue and green to the screen image for a darker color.
User Color Individual adjustments for red (R), green (G), and blue (B).
1. To select color (R, G or B) press button [2].
2. To adjust selected color, pressSandT.
Important: If you select RECALL from the Main Menu when the product is
set to a Preset Timing Mode, colors return to the 6500K factory preset.
Information displays the timing mode (video signal input) coming from the
graphics card in the computer, the LCD model number, the serial number, and
the ViewSonic® website URL. See your graphics card’s user guide for
instructions on changing the resolution and refresh rate (vertical frequency).
NOTE: VESA 1680 x 1050 @ 60Hz (recommended) means that the resolution is
1680 x 1050 and the refresh rate is 60 Hertz.
Manual Image Adjust Sub-menu
ViewSonic Corporation
18
Confidential - Do Not Copy
VG1930wm-3
Control
Explanation
H. Size (Horizontal Size) adjusts the width of the screen image.
H./V. Position (Horizontal/Vertical Position) moves the screen image left or
right and up or down.
Fine Tune sharpens the focus by aligning text and/or graphics with pixel
boundaries.
NOTE: Try Auto Image Adjust first.
Sharpness adjusts the clarity and focus of the screen image.
Setup Menu displays the menu shown below:
Language Select allows the user to choose the language used in the menus and
control screens.
ViewSonic Corporation
19
Confidential - Do Not Copy
VG1930wm-3
Control
Explanation
Resolution Notice allows the user to enable or disable this notice.
If you enable the Resolution Notice shown above and your computer is set at a
resolution other than 1440 x 900, the following screen appears.
OSD Position allows the user to move the OSD menus and control screens.
OSD Timeout sets the length of time the OSD screen is displayed. For example,
with a “30 second” setting, if a control is not pushed within 30 seconds, the
display screen disappears.
OSD Background allows the user to turn the OSD background On or Off.
Memory Recall returns the adjustments back to factory settings if the display is
operating in a factory Preset Timing Mode listed in the Specifications of this
manual.
ViewSonic Corporation
20
Confidential - Do Not Copy
VG1930wm-3
4. Circuit Description
The TSUM56AL is total solution graphics processing IC for LCD monitors with panel resolutions up to SXGA. It is
configured with a high-speed integrated triple-ADC/PLL, an integrated DVI receiver, a high quality display processing engine,
and an integrated output display interface that can support
LVDS panel interface format. To further reduce system costs, the
TSUM56AWHL-LF-1 also integrates intelligent power management control capability for green-mode requirements and
spread- spectrum support for EMI management.
The TSUM56AL incorporates the world’s first coherent oversampled RGB graphics ADC in a monitor controller system. The
oversampling ADC samples the input RGB signals at a frequency that is much higher than the signal source pixel rate. This
can preserve details in the video signal that ordinarily would be lost due to input signal jitter or bandwidth limitations in
non-oversampled systems. The TSUM56AL also incorporates a new Dynamic Frame Rate (DFR) generator for the digital
output video to the display panel that preserves the advantages of a fixed output clock rate, while eliminating the output end of
frame short-line.
ViewSonic Corporation
21
Confidential - Do Not Copy
VG1930wm-3
Analog EDID
Time:
15:51:56
Date: Mon Oct 23, 2006
______________________________________________________________________
______________________________________________________________________
VIEWSONIC CORPORATION
EDID Version # 1, Revision # 3
DDCTest For: ViewSonic VG1930wm
______________________________________________________________________
______________________________________________________________________
EDID Block 0, Bytes 0-127
128 BYTES OF EDID CODE:
0
1
2
3
4
5
6
7
8
9
________________________________________
0 | 00 FF FF FF FF FF FF 00 5A
63
10 | 1E 9D 01 01 01 01 01 10 01
03
20 | 0E 29 1A 78 2E E5 B5 A3 55
49
30 | 99 27 13 50 54 BF EF 80 95
00
40 | 95 0F 81 80 81 40 71 4F 01
01
50 | 01 01 01 01 9A 29 A0 D0 51
84
60 | 22 30 50 98 36 00 9A 00 11
00
70 | 00 1C 00 00 00 FF 00 51 43
36
80 | 30 36 30 31 30 30 30 30 31
0A
90 | 00 00 00 FD 00 32 4B 1E 52
0E
100 | 00
0A 20 20 20 20 20 20 00
00
110 | 00
FC 00 56 47 31 39 33 30
77
120 | 6D
0A 20 20 20 20 00 DD
(08-09) ID Manufacturer Name ________________ = VSC
(11-10) Product ID Code _____________________ = 9D1E
(12-15) Last 5 Digits of Serial Number ______ = Not Used
(16)
Week of Manufacture _________________ = 01
(17)
Year of Manufacture _________________ = 2006
(10-17) Complete Serial Number ______________ = See Descriptor Block
(18)
EDID Version Number _________________ = 1
(19)
EDID Revision Number ________________ = 3
(20)
VIDEO INPUT DEFINITION:
Analog Signal
0.700, 0.300 (1.000 Vp-p)
Separate Syncs, Composite Sync, Sync on Green
(21)
Maximum Horizontal Image Size ________________
=
410 mm
(22)
Maximum Vertical Image Size __________________
=
260 mm
ViewSonic Corporation
22
Confidential - Do Not Copy
VG1930wm-3
(23)
Display Gamma ________________________________
(24)
Power Management and Supported Feature(s):
=
2.20
Active Off/Very Low Power, Standard Default Color Space,
Preferred Timing Mode
Display Type = R/G/B Color
(25-34) CHROMA INFO:
Red X - 0.640 Green X - 0.286 Blue X - 0.154 White X - 0.313
Red Y - 0.334 Green Y - 0.599 Blue Y - 0.077 White Y - 0.329
(35)
ESTABLISHED TIMING I:
720 X 400 @ 70Hz (IBM,VGA)
640 X 480 @ 60Hz (IBM,VGA)
640 X 480 @ 67Hz (Apple,Mac II)
640 X 480 @ 72Hz (VESA)
640 X 480 @ 75Hz (VESA)
800 X 600 @ 56Hz (VESA)
800 X 600 @ 60Hz (VESA)
(36)
ESTABLISHED TIMING II:
800 X 600 @ 72Hz (VESA)
800 X 600 @ 75Hz (VESA)
832 X 624 @ 75Hz (Apple,Mac II)
1024 X 768 @ 60Hz (VESA)
1024 X 768 @ 70Hz (VESA)
1024 X 768 @ 75Hz (VESA)
1280 X 1024 @ 75Hz (VESA)
(37)
Manufacturer's Reserved Timing:
1152 X 870 @ 75Hz (Apple,Mac II)
(38-53) Standard Timing Identification:
1440 X 900 @60Hz
1440 X 900 @75Hz
1280 X 1024 @60Hz
1280 X 960 @60Hz
1152 X 864 @75Hz
Not Used
Not Used
Not Used
(54-71) Detailed Timing / Descriptor Block 1:
1440x900 Pixel Clock: 106.50 MHz
Horizontal Image Size: 410 mm
Vertical Image Size: 256 mm
Refreshed Mode: Non-Interlaced
Normal Display - No Stereo
Horizontal:
ViewSonic Corporation
23
Confidential - Do Not Copy
VG1930wm-3
Active Time: 1440 pixels
Blanking Time: 464 pixels
Sync Offset: 80 pixels
Sync Pulse Width: 152 pixels
Border: 0 pixels
Frequency: 55.93 KHz
Vertical:
Active Time: 900 lines
Blanking Time: 34 lines
Sync Offset: 3 lines
Sync Pulse Width: 6 lines
Border: 0 lines
Frequency: 59.89 Hz
Digital Separate, Horizontal Polarity (-) Vertical Polarity (+)
(72-89) Detailed Timing / Descriptor Block 2:
Monitor Serial Number:
QC6060100001
(90-107) Detailed Timing / Descriptor Block 3:
Monitor Range Limits:
Min Vertical Freq - 50 Hz
Max Vertical Freq - 75 Hz
Min Horiz. Freq - 30 KHz
Max Horiz. Freq - 82 KHz
Pixel Clock - 140 MHz
Secondary GTF - Not Supported
(108-125) Detailed Timing / Descriptor Block 4:
Monitor Name:
VG1930wm
(126)
(127)
No Extension EDID Block(s)
CheckSum OK
ViewSonic Corporation
24
Confidential - Do Not Copy
VG1930wm-3
Digital EDID
Time:
15:52:31
Date: Mon Oct 23, 2006
VIEWSONIC CORPORATION
EDID Version # 1, Revision # 3
DDCTest For: ViewSonic VG1930wm
EDID Block 0, Bytes 0-127
128 BYTES OF EDID CODE:
0
1
2
3
4
5
6
7
8
9
________________________________________
0 | 00 FF FF FF FF FF FF 00 5A
63
10 | 1E 9D 01 01 01 01 01 10 01
03
20 | 80 29 1A 78 2E E5 B5 A3 55
49
30 | 99 27 13 50 54 BF EF 80 95
00
40 | 95 0F 81 80 81 40 71 4F 31
0A
50 | 01 01 01 01 9A 29 A0 D0 51
84
60 | 22 30 50 98 36 00 9A 00 11
00
70 | 00 1C 00 00 00 FF 00 51 43
36
80 | 30 36 30 31 30 30 30 30 31
0A
90 | 00 00 00 FD 00 32 4B 1E 52
0E
100 | 00
0A 20 20 20 20 20 20 00
00
110 | 00
FC 00 56 47 31 39 33 30
77
120 | 6D
0A 20 20 20 20 00 32
(08-09) ID Manufacturer Name ________________ = VSC
(11-10) Product ID Code _____________________ = 9D1E
(12-15) Last 5 Digits of Serial Number ______ = Not Used
(16)
Week of Manufacture _________________ = 01
(17)
Year of Manufacture _________________ = 2006
(10-17) Complete Serial Number ______________ = See Descriptor Block
(18)
EDID Version Number _________________ = 1
(19)
EDID Revision Number ________________ = 3
(20)
VIDEO INPUT DEFINITION:
Digital Signal
Non - VESA DFP 1.x Compatible
(21)
Maximum Horizontal Image Size ________________
=
410 mm
(22)
Maximum Vertical Image Size __________________
=
260 mm
(23)
Display Gamma ________________________________
=
2.20
(24)
Power Management and Supported Feature(s):
ViewSonic Corporation
25
Confidential - Do Not Copy
VG1930wm-3
Active Off/Very Low Power, Standard Default Color Space,
Preferred Timing Mode
Display Type = R/G/B Color
(25-34) CHROMA INFO:
Red X - 0.640 Green X - 0.286 Blue X - 0.154 White X - 0.313
Red Y - 0.334 Green Y - 0.599 Blue Y - 0.077 White Y - 0.329
(35)
ESTABLISHED TIMING I:
720 X 400 @ 70Hz (IBM,VGA)
640 X 480 @ 60Hz (IBM,VGA)
640 X 480 @ 67Hz (Apple,Mac II)
640 X 480 @ 72Hz (VESA)
640 X 480 @ 75Hz (VESA)
800 X 600 @ 56Hz (VESA)
800 X 600 @ 60Hz (VESA)
(36)
ESTABLISHED TIMING II:
800 X 600 @ 72Hz (VESA)
800 X 600 @ 75Hz (VESA)
832 X 624 @ 75Hz (Apple,Mac II)
1024 X 768 @ 60Hz (VESA)
1024 X 768 @ 70Hz (VESA)
1024 X 768 @ 75Hz (VESA)
1280 X 1024 @ 75Hz (VESA)
(37)
Manufacturer's Reserved Timing:
1152 X 870 @ 75Hz (Apple,Mac II)
(38-53) Standard Timing Identification:
1440 X 900 @60Hz
1440 X 900 @75Hz
1280 X 1024 @60Hz
1280 X 960 @60Hz
1152 X 864 @75Hz
640 X 400 @70Hz
Not Used
Not Used
______________________________________________________________________
(54-71) Detailed Timing / Descriptor Block 1:
1440x900 Pixel Clock: 106.50 MHz
______________________________________________________________________
Horizontal Image Size: 410 mm
Vertical Image Size: 256 mm
Refreshed Mode: Non-Interlaced
Normal Display - No Stereo
Horizontal:
Active Time: 1440 pixels
ViewSonic Corporation
Blanking Time: 464 pixels
26
Confidential - Do Not Copy
VG1930wm-3
Sync Offset: 80 pixels
Border: 0 pixels
Sync Pulse Width: 152 pixels
Frequency: 55.93 KHz
Vertical:
Active Time: 900 lines
Blanking Time: 34 lines
Sync Offset: 3 lines
Sync Pulse Width: 6 lines
Border: 0 lines
Frequency: 59.89 Hz
Digital Separate, Horizontal Polarity (-) Vertical Polarity (+)
______________________________________________________________________
(72-89) Detailed Timing / Descriptor Block 2:
Monitor Serial Number:
QC6060100001
______________________________________________________________________
(90-107) Detailed Timing / Descriptor Block 3:
Monitor Range Limits:
Min Vertical Freq - 50 Hz
Max Vertical Freq - 75 Hz
Min Horiz. Freq - 30 KHz
Max Horiz. Freq - 82 KHz
Pixel Clock - 140 MHz
Secondary GTF - Not Supported
______________________________________________________________________
(108-125) Detailed Timing / Descriptor Block 4:
Monitor Name:
VG1930wm
(126)
No Extension EDID Block(s)
(127)
CheckSum OK
ViewSonic Corporation
27
Confidential - Do Not Copy
VG1930wm-3
5. Adjustment Procedure
Function Test and Alignment Procedure
1. All Modes Reset
You should do “All Model Reset” (Refer to Chap 3. Hot Keys for Function Controls) first. This action will allow
you to erase all end-user’s settings and restore the factory defaults.
2. Auto Image Adjust
The Auto Adjust is aimed to offer a best screen quality by built-in ASIC. For optimum screen quality, the user
has to adjust each function manually.
A.Turn the computer and LCD monitor on.
B. Press the ‘Auto Image Adjust’ OSD function to Auto Adjust.
C. The LCD monitor will start the Auto Adjust process automatically and run for 10 consecutive seconds, during
which time you will notice the image change.
3. Firmware
Test Patten: Burn in Model (Refer to Chap3. Hot Keys for Function Control)
-Make sure the F/W is the latest version.
4. DCC
Test Patten: EDID program
-Make sure it can pass test program.
5. Window Shut Down
Test Signal: 1400*900@60Hz
Test Pattern:
Checkered Pattern Every One Pixel (50%Green & 50%Blue)
Inspection Item: Flicker, Mura
6. Window BG
Test Signal: 1400*900@60Hz
Test Pattern:
Window standard pattern
Inspection Item: Line Defect, Function Defect & Mura
7. 25 Gray
Test Signal: 1400*900@60Hz
Test Pattern:
Full Screen 25% White (Gray)
Inspection Item: Particle, Line Defect & Mura
8. 50 Gray
Test Signal: 1400*900@60Hz
Test Pattern:
Full Screen 50% White (Gray)
Inspection Item: Bright Dot, Particle, Line Defect & Mura
ViewSonic Corporation
28
Confidential - Do Not Copy
VG1930wm-3
9. White Box
Test Signal: 1400*900@60Hz
Test Pattern:
Window standard pattern
Inspection Item: Particle, Line Defect, Power, Image Remain & Mura
10. Black Box
Test Signal: 1400*900@60Hz
Test Pattern:
Window standard pattern
Inspection Item: Bright Dot, Line Defect & Power
11. RED
Test Signal: 1400*900@60Hz
Test Pattern:
Full Screen Red
Inspection Item: Bright Dot, Partial & Line Defect
12. Green
Test Signal: 1400*900@60Hz
Test Pattern:
Full Screen Green
Inspection Item: Bright Dot, Partial & Line Defect
13. Blue
Test Signal: 1400*900@60Hz
Test Pattern:
Full Screen Green
Inspection Item: Bright Dot, Partial & Line Defect
14. Gray_Scale_0-100_V64
Test Signal: 1400*900@60Hz
Test Pattern:
Vertical 64 (256) Gray Scale (Right → Left,From 0 to 100% White)
Inspection Item: Line Defect & Function Defect
ViewSonic Corporation
29
Confidential - Do Not Copy
VG1930wm-3
15. Function Test Display pattern
Item
Pattern
Description
Remark
1
Gray_Scale_0-100_V
Vertical 64 (256) Gray Scale (右→左,From 0 to 100% White)
Figure 1
2
Gray_Scale_0-100_H
Horizontal 64 (256) Gray Scale (上→下,From 0 to 100% White)
Figure 2
3
Black
Full Screen Black
Figure 3
4
Red
Full Screen 50% Red
Figure 4
5
Green
Full Screen 50% Green
Figure 5
6
Blue
Full Screen 50% Blue
Figure6
7
White
Full Screen White
Figure7
8
Black_Tile
Black Tile Under White Background
Figure 8
Figure 1
Figure 2
Figure 3
Figure 4
ViewSonic Corporation
30
Confidential - Do Not Copy
VG1930wm-3
Figure 5
Figure 6
Figure 7
Figure 8
ViewSonic Corporation
31
Confidential - Do Not Copy
VG1930wm-3
BIOS update procedure
1. To setup ISP environment
Hardware:
PC or Notebook , Parallel(Printer) cable , ISP tool( Fig 1)
Software:
ISP driver .
If the O.S. was Win2000 or Win XP please have to install PORT95NT.exe
Fig1
In order to ensure can execute ISP program, please set BIOS in PC or Notebook as Fig 2
Fig 2
ViewSonic Corporation
32
Confidential - Do Not Copy
VG1930wm-3
2. Install ISP
2.1 User could download ISP driver and PORT95NT install file from Myson Century website (http://www.myson.com.tw/)
2.2 After extracting the zip file, the total files list as Fig 2.2, and double click the file of setup.exe to install.
Fig 2.2
2.3 Press “Next" button to continue., see Fig 2.3
Fig 2.3
ViewSonic Corporation
33
Confidential - Do Not Copy
VG1930wm-3
2.4 Keep default setting or press “Change" button for selecting the path that you want , and then
press“Next"button to continue, see Fig 2.4.
Fig 2.4
2.5 Press “Install" button to continue, see Fig 2.5
Fig 2.5
ViewSonic Corporation
34
Confidential - Do Not Copy
VG1930wm-3
2.6 The Installer Information shows package warning, press “Ignore" button to continue, see Fig 2.6.
Fig 2.6
2.7 Installation has finished, press “Finish" button, see Fig 2.7.
Fig 2.7
ViewSonic Corporation
35
Confidential - Do Not Copy
VG1930wm-3
3. ISP security code
3.1 After installation, we could find the shortcut in the setting path or the program bar (default setting),
see Fig 3.1.
Fig 3.1
2.2 Security file is a key to use ISP function, press “確定" button, see Fig 3.2.
Fig 3.2
ViewSonic Corporation
36
Confidential - Do Not Copy
VG1930wm-3
3.3 The warning is used to remind user of that different CPU rate may cause ISP function fail(it is limited by IIC protocol),
press “確定" button, see Fig 3.3.
Fig 3.3
2.4 Press“Create Security File" button to key in security code. Adjusting bar to decrease speed of IIC bus, see Fig 3.4.
Fig 3.4
ViewSonic Corporation
37
Confidential - Do Not Copy
VG1930wm-3
3.5 At least 2 Command No of security code, see Fig 3.5, and different security code between hardware ISP and software ISP.
The security code of software ISP is set by user while coding, but the security code of hardware ISP is set by Myson Century.
Fig 3.5
ViewSonic Corporation
38
Confidential - Do Not Copy
VG1930wm-3
3.6
Fig 3.6 shows the setting for security code of hardware ISP, it needs 4 Command No, and key in command sequentially
for 94, 94, AC, CA, 53.
Fig 3.6
ViewSonic Corporation
39
Confidential - Do Not Copy
VG1930wm-3
3.7
Fig 3.7 shows the setting for security code of software ISP, it needs 2 Command No, and key in command sequentially
for 7C, 4C, 77. The Command No and command must be set by user while coding. About the detail of setting, please
refer to Section 6 Boot code of ISP.
Fig 3.7
ViewSonic Corporation
40
Confidential - Do Not Copy
VG1930wm-3
4. Use ISP to program MCU
4.1 Select MTV type first, load the binary or Intel hex file that you want to program into the MCU, and select “Auto" item,
then press “RUN" button, see Fig 4.1.
4.2 If user changes the MTV type, it must load file again, or the buffer of load file will be cleared.
4.3 CRC (cyclic redundancy check): the host can check CRC register's result instead of reading every byte in flash. The
message of Check MCU CRC OK means that the Host verify ok for the progress of program.
Step 2
Step 1
Step 3
Fig 4.1
ViewSonic Corporation
41
Confidential - Do Not Copy
VG1930wm-3
5 Use ISP to read MCU content
5.1 Only software ISP could read the MCU content, it is according to program the boot code while coding. The limitation is
used for the security of customer's code. Select “Read Target" item, and press“RUN" button, the MCU content
will show as Fig 5.1.
Fig 5.1
ViewSonic Corporation
42
Confidential - Do Not Copy
VG1930wm-3
5.2 If user uses hardware ISP to read MCU content, it shows as Fig 5.2.
Fig 5.2
ViewSonic Corporation
43
Confidential - Do Not Copy
VG1930wm-3
6 Re-entry the ISP Mode
When you could not select or click `Reset MCU' button and enter ISP mode again, you refer the message as below:
ViewSonic Corporation
44
Confidential - Do Not Copy
VG1930wm-3
Note:
(1)Disable the `Enter ISP Mode' option to avoid the error message display.
(2)If you using the MTV312M64 or before MCU serials, the MCU will always in `ISP Mode'even programming fail or
erase MCU that instead of select or press `Reset MCU'.
ViewSonic Corporation
45
Confidential - Do Not Copy
VG1930wm-3
7. Boot code of ISP
7.1 Hardware ISP
(1) Without boot code
(2) Fixed security code: 94, 94, AC, CA, 53
(3) Attention to the pin of HSCL (1) and HSDA (1) should keep in enable
(4) MTV412M, MTV512M, CS8954 support hardware ISP
7.2 Software ISP
(1) With boot code
(2) User define the security code
(3) Attention to the pin of HSCL (1) and HSDA (1) should keep in enable
(4) Only software ISP could read the MCU content
(5) MTV212M, MTV312M, MTV230M, MTV412M, MTV512M, CS8954 support software ISP
7.3 Boot code of software ISP
(1) Initialize MCU
(a) Define the I/O pin to HSCL (1) and HSDA (1)
(b) Define the slave B address
(c) Enable 8051 INT1 (ISR 2)
(2) Coding for INT1 while get into ISP mode
(a) Clear watchdog to prevent reset during ISP period
(b) Disable all interrupt to prevent CPU wake-up
(c) Write ISP slave address
(d) Write 93h to ISP enable address to enable ISP
(e) Enter 8051 idle mode
ViewSonic Corporation
46
Confidential - Do Not Copy
VG1930wm-3
7.4 The followings show the relationship between the code and the security code.
ViewSonic Corporation
47
Confidential - Do Not Copy
VG1930wm-3
8. ISP Adaptor Schematic
9. Adaptor Linking
ISP Adaptor
Connect with
Printer Cable
25Pins to 25Pins
The Monitor Set
PC/HOST
Connect with
VGA Cable
15Pins to 15Pins
ViewSonic Corporation
48
Confidential - Do Not Copy
VG1930wm-3
Packing For Shipping And Disassembly Procedure
Packing For Shipping
1. Packing Procedure
1.1 Paste protection film to protect the monitor. (Figure 1)
1.2 Put the monitor in the PE bag and cover the small PE bag on the stand. (Figure 2)
Figure 1
Figure 2
1.3 Fold the left bottom of PE bag’s opening mouth to the back of the monitor. (Figure 3)
1.4 Take the left side cushion and fix it onto the left side of the monitor. (Figure 4)
Figure 3
ViewSonic Corporation
Figure 4
49
Confidential - Do Not Copy
VG1930wm-3
1.5 Fold the right side PE bag to the back of monitor, and pull the PE bag’s opening mouse to the back of the
monitor.(Figure5)
1.6 Take the left side cushion and fix it onto the left side of the monitor.( Figure 6)
Figure 5
Figure6
1.7 Put the monitor into the carton, panel screen should face to carton handle side, as last, close the carton. (Figure 7)
Figure 7
ViewSonic Corporation
50
Confidential - Do Not Copy
VG1930wm-3
Monitor Assembly and Disassembly
1 Separate Stand Assy
Step 1 :
Separate the Stand Cover.
Step 2 :
Loose the Stand 4 Screws
Step 3 :
Completed.
ViewSonic Corporation
51
Confidential - Do Not Copy
VG1930wm-3
2 Separate Bezel
Step 1 :
Loose Rear Cover 2 Screws.
Step 2 :
Separate the front Bezel hooks to
take Bezel and Panel apart.
Step 3:
Separate the side hooks of Bezel to
take Bezel and Rear Cover apart.
Step 4 :
Completed.
ViewSonic Corporation
52
Confidential - Do Not Copy
VG1930wm-3
3 Remove Panel
Step 1 :
Disassemble 2 screws of bottom of panel and
lift up Panel from Rear cover
Step 2 :
Remove 2 pieces Backlight Wires
and A/D Board connect Wire.
Step3 :
Completed.
ViewSonic Corporation
53
Confidential - Do Not Copy
VG1930wm-3
4 Remove Power key Board and function key Board
Step 1 :`
Remove 2 pieces Wires of
Board
Step 2 :`
Remove connect wire of
Step 3 :`
Remove
Wire of
Power Key
Power Key Board
Power Key Board
Step4:
Completed.
ViewSonic Corporation
54
Confidential - Do Not Copy
VG1930wm-3
5 Separate Metal Cover
Step1:`
Loose all Screws of support plate
and Metal Cover
Step2:`
Remove Support
plate
Step3:`
Separate Metal Cover
Step4:`
Completed.
ViewSonic Corporation
55
Confidential - Do Not Copy
VG1930wm-3
6 Remove Lips Board And A/D Board
Step 1 :
Loose 4 Screws of Lips Board
Step 2 :
Loose 3 Screws of A/D Board
Step 3 :
Completed
ViewSonic Corporation
56
Confidential - Do Not Copy
VG1930wm-3
7 Change Lips Board and A/D Board
Step 1 :
Place new A/D Board and fasten
4 screws (wihte-Left,red-Right)
`
Step 2 :
Assemble Lips Board
Step 3 :
Completed
ViewSonic Corporation
57
Confidential - Do Not Copy
VG1930wm-3
8 Assemble Metal Cover and Support plate
Step 1 :
Assemble Metal Cover
Step 2 :
Assemble Support plate
Step 3 :
Completed
ViewSonic Corporation
58
Confidential - Do Not Copy
VG1930wm-3
9 Assemble Power key Board and function key Board
Step 2:
Insert the wire of Power key
Board
Step 2:
Place new Power key Board on
Bezel hooks
Step 3:
Insert 2 pieces Audio wires of
Power Key Board
Step 4:
Insert connect wire of
Power Key Board
ViewSonic Corporation
59
Confidential - Do Not Copy
VG1930wm-3
Step5:
Insert the connect wire of
Key Board
Step6:
Assemble Key Board of
Bezel hooks
Step7:
Completed
ViewSonic Corporation
60
Confidential - Do Not Copy
VG1930wm-3
10 Assemble Panel
Step 1 :
Insert 1 piece of Backlight
wires
Step 2 :
Insert
Wires of A/D Board
Step 3 :
Insert another piece backlight
wire of Lips Board
Step 4 :
Completed.
ViewSonic Corporation
61
Confidential - Do Not Copy
VG1930wm-3
11 Assemble Bezel
Step 1 :
Place the rear cover and Assembly
the right hooks of the Bezel first .
Step 2 :
Assemble Bezel hooks
Bezel and Panel apart.
Step 3 :
Completed.
12 Assemble Stand and Hinge Cover
Step 1 :
Assemble Stand
ViewSonic Corporation
62
Confidential - Do Not Copy
VG1930wm-3
Step2 :
Assemble Hinge Cover
Step 3:
Completed.
ViewSonic Corporation
63
Confidential - Do Not Copy
VG1930wm-3
6. Troubleshooting Flow Chart
Defect Mode
Failure Analysis
Light On Test
Repair
Testing
※ “ Panel Change” Should be Performed to Level 3 Repair
Flash Dots
Abnormal
Display
Bright Dot
Dark Dot
Backlight
Light Leakage
Mura
Check Panel
Panel Change
Image Sticking
Brightness spot
Particle
Dot Defect
Image Remain
Group Bright
Dots
Others Cosmetics
Defect
Next Step
NG
A
ViewSonic Corporation
TEST
Completed
64
Confidential - Do Not Copy
VG1930wm-3
Defect Mode
Failure Analysis
Repair
Testing
※ “ Panel Change” Should be Performed to Level 3 Repair
A
Display Noise
Power on
Check PCBA
Display
AD/B Change
LIPS Change
Abnormal
Flicker
CNT/B Change
Beat Display
Flicker
Check Panel
Panel Change
Beat Display
Shut Down
AD/B Change
Display Wave
Check PCBA
LIPS Change
CNT/B Change
No Backlight
Check Panel
Panel Change
Check LIPS
LIPS Change
Next Step
NG
B
ViewSonic Corporation
TEST
Completed
65
Confidential - Do Not Copy
VG1930wm-3
Failure Analysis
Repair
Testing
※ “ Panel Change” Should be Performed to Level 3 Repair
B
Display White
Out
Check PCBA
AD/B Change
LIPS Change
Booting Delay
Check PCBA
Brightness
AD/B Change
Even
Abnormal
LIPS Change
Check PCBA
Beat Display
No Backlight
Check Panel
Check LIPS
Panel Change
LIPS Change
No signal
AD/B Change
R.G.B
Check PCBA
CNT/B Change
Check Wire
VGA cable
Display
Abnormal
DVI cable
Gray Scale
Display
Abnormal
Check Panel
Next Step
Panel Change
NG
TEST
C
Completed
ViewSonic Corporation
66
Confidential - Do Not Copy
VG1930wm-3
Defect Mode
Failure Analysis
Repair
Testing
※ “ Panel Change” Should be Performed to Level 3 Repair
C
Horizontal
Line Defect
Vertical
Weak Line
Check PCBA
AD/B Change
Check Panel
Panel Change
Horizontal
Weak Line
Vertical
Band Defect
Horizontal
Band Defect
Power Saving
Display
Check PCBA
AD/B Change
Abnormal
AD/B Change
Peculiar Smell
Check PCBA
LIPS Change
Next Step
NG
TEST
Complete
ViewSonic Corporation
67
Confidential - Do Not Copy
VG1930wm-3
Defect Mode
Failure Analysis
Repair
Testing
※ “ Panel Change” Should be Performed to Level 3 Repair
AD/B Change
LIPS Change
Power ON/OFF
No Power
Abnormal
Turn Off
Check PCBA
CNT/B Change
Check PCBA
LED/B Change
Abnormal
Check Wire
Check LIPS
CNT/B Cable
LIPS Change
AD/B Change
LED Display
Abnormal
LED Off
Check PCBA
LIPS Change
LED Dark
LED/B Change
LED Abnormal
LED Loss
Check Wire
CNT/B Cable
LED Flicker
LIPS Change
Next Step
NG
TEST
Completed
ViewSonic Corporation
68
Confidential - Do Not Copy
VG1930wm-3
Defect Mode
Failure Analysis
Repair
Testing
※ “ Panel Change” Should be Performed to Level 3 Repair
Abnormal BIOS
OSD Key
&OSD
AD/B Change
Unavailable
CNT/B Change
OSD Can’t
Input
Check PCB
LIPS Change
OSD Can’t
Read
OSD No
CNT/B cable
Display
Check Wire
OSD Jiggle
VGA cable
DVI cable
OSD Display
Abnormal
Abnormal
LVDS cable
Check BIOS
BIOS Update
AD/B Change
Voice Loss
Loudspeaker
CNT/B Change
Abnormal
Loud
LIPS Change
Check PCBA
L/R
Abnormal
Check Wire
No Voice
L/R Same
C/B Cable Change
Loudspeaker
Check Loudspeaker
Volume
Loudspeaker
Next Step
Change
NG
Noise
TEST
Completed
ViewSonic Corporation
69
Confidential - Do Not Copy
VG1930wm-3
Defect Mode
Failure Analysis
Repair
Testing
※ “ Panel Change” Should be Performed to Level 3 Repair
Other Abnormal
Display
Display Shut
Check PCBA
Down
AD/B Change
LIPS Change
CNT/B Change
Check Panel
Display Flicker
Check PCBA
((tapping )
AD/B Change
CNT/B Change
Check Panel
DVI Signal
Panel Change
Check PCB
Panel Change
AD/B Change
Display
Abnormal
Check EDID Code
Next Step
EDID Update
NG
TEST
Complete
ViewSonic Corporation
70
Confidential - Do Not Copy
VG1930wm-3
Trouble Shooting Analysis
Check the information in this section to see if the problems can be solved before requesting repair.
Note: The consumers are only allowed to solve the problems described as below. Any unauthorized product
modification, or failure to follow instructions supplied with the product will end the warranty immediately.
z No image
‹ Make sure power button is ON.
‹ Check whether the LCD monitor and computer power cords are plugged and whether there is a supply of power.
z No Signal Input
‹ Check the signal connection between the computer and LCD monitor.
z “Out of Range”
‹ Check the computer image output resolution and frequency and compare the value with the preset values (Please
refer to [Appendix-Display Mode]).
z Fuzzy Image
‹ Adjust Phase.
z Image too bright
‹ Adjust brightness and contrast by OSD.
z Image too dark
‹ Adjust brightness and contrast by OSD.
z Irregular image
‹ Check the signal connection between the computer and LCD monitor.
‹ Perform Auto Adjust.
z Distorted image
‹ Reset the LCD monitor
‹ Take off extra accessories (such as signal extension cord).
z Image is not centered
‹ Use OSD Image Menu to adjust H_Position and V_Position.
‹ Check image size setting.
‹ Perform Auto Adjust.
z Size is not appropriate
‹ Use OSD Image Menu to adjust H_Position and V_Position.
‹ Check image size setting.
‹ Perform Auto Adjust.
z Uneven color
‹ Use OSD Color Menu to adjust color setting.
z Color too dark
‹ Use OSD Color Menu to adjust color setting.
z Dark area distorted
‹ Use OSD Color Menu to adjust color setting.
z White color is not white
‹ Use OSD Color Menu to adjust color setting.
ViewSonic Corporation
71
Confidential - Do Not Copy
VG1930wm-3
ViewSonic Corporation
VCC3.3
VLCD
VCC1.8
+5V
+12V
DVI5V
DVI5V
VGA5V
VGA5V
3.INPUT
VCTRL
INVERTER
5.POWER
VLCD
VCC1.8
VCC3.3
+12V
on_Panel
VGA5V Adj_BACKLIGHT
on_BACKLIGHT
+5V
DVI5V
B02
VGA5V
DVI5V
B03
B+
BG+
GR+
RCLK+
CLK-
B+
BG+
GR+
RCLK+
CLK-
BACKLIGHT CONTROL
6.SCALER
on_PANEL
adj_BACKLIGHT
on_BACKLIGHT
VCTRL
SDA_D
SCL_D
DET_DVI
DET_VGA
SDA_A
SCL_A
SDA_A
SCL_A
SDA_D
SCL_D
DET_DVI
DET_VGA
RIN
GNDR
GIN
GNDG
SOG
BIN
GNDB
HSYNC
VSYNC
RIN
GNDR
GIN
GNDG
SOG
BIN
GNDB
HSYNC
VSYNC
B04
VCC3.3
PB[0..9]
PA[0..9]
+5V
B5
+5V
Volume
AUDIO_MUTE
+5V
+12V
+3V3
+12V
PB[0..9]
72
Confidential - Do Not Copy
+5V
+12V
VLCD
VCC3.3
KEY PAD
AC TO DC POWER
4.PANEL INTERFACE
VLCD
VCC_TEST&ODCTRL
VCC3V3
PA[0..9]
2.AUDIO
B4
LVDS OUTPUT
PB[0..9]
VCC_TEST&ODCTRL
PA[0..9]
Volume
AUDIO_MUTE
VCC3.3
+5V
VCC1.8
VCC1.8
7. Block Diagram
VSC VG1930wm-3 A/D Board BLOCK DIAGRAM
VG1930wm-3
8. Schematic Diagrams
CN2
SCJ-0356M5(B)
CN13
1
2
3
4
5
U_GND
3
2
1
+5Vau
+5Vau
+12V 6
PITCH 2.0 180度
+5V
FB10
1
220uF/16V/NC
Vau
120 OHM BEAD
I
O
U11
2
U_GND
G
3
+ TC23
Connect the net +5Vau & +5V
C1
UTC7805/NC
0.1uF
2
10
15
U_GND
VOR
1
2
3
1
2
BW FCM1608K-300T07
C2 1uF
R2
20K
5
TC33
LEFTIN
VOL
L2
1
2
BW FCM1608K-300T07
C4 1uF
R4
R5
Shutdown
+5V
去掉得元件06/08/17
6
Vin2
7
20K -> 33K
1
8
VO2
+OUT1
16
2
1
SE/BTL
12
+OUT2
9
-OUT2
11
PT2300
Shutdown
GND
Rout
3
7 Volume
R10
4.7K
2
NC -> 1K
3
3
R9
Q2
MMBT3904L
Q1
1
R12
2K
U_GND
U_GND
10K -> 100K
U_GND
CN5
1
2
Lout
C3
R126 300K
R8
10K
MMBT3904L
2
Shutdown
Vau
R3
Vau
R6
4.7K
+5V
22K
1
CN1
U_GND
R7
4.7K
14
+5V
+5V 4,6,7
R11
-OUT1
Vin1
2.2uF/16V
13 By pass
20K
U_GND
Vol
+
U_GND
PITCH 2.0 180度
4
20K -> 33K
DC Vol
RIGHTIN
CN14
L1
U2
Vcc
Vcc
Vcc
R1
0.1uF
Add the capacitor for balance the Vau & DC Vol
C71
0.1uF
U_GND
R13
330
Shutdown
U_GND
TC2
+
+5V
R14
10uF/16V
R15
U_GND
10K---4.7K
RA3
0R/NC
120 OHM BEAD
FB11
0R
Q3
AO3401
3
4.7K--10K
C5
U_GND
Q4
1
U_GND
L0603 --> L0805
MMBT3904L
+
0.1uF
U_GND
120 OHM BEAD
FB1
2
R17
7 AUDIO_MUTE
RA1
RA2
0R
10K---22K
+5Vau
Vau
TC3
10uF/16V
R18
10K
U_GND
U_GND
ViewSonic Corporation
Model
Title
Date
ViewSonic Corporation
73
Confidential - Do Not Copy
VG1930wm-3
AUDIO
Rev:
0.047uF
C7
0.047uF
R
R21
56Ω 1/16W
C8
0.047uF
R22
470Ω 1/16W
C9
1000pF
CN6
DB15
R25
R_GND
R28
100Ω 1/16W
C12
0.047uF
B_GND
VGA5V
VGA5V
HPDVGA
D2
BAV99
3
B
D3
BAV99
D1
BAV99
R29
C13
0.1uF
0.1uF
C14
C15
GIN 7
RIN 7
GNDB 7
GNDG 7
GNDR 7
+5V
VGA5V 6
0.1uF
0/1K
D4
16
17
R24
G
2
15
G_GND
1
14
SCL_A
0.047uF
2
VSI
0.047uF
C11
3
13
C10
100Ω 1/16W
1
HSI
100Ω 1/16W
R27
2
12
R26
G_GND
R_GND
BIN 7
SOG 7
R
3
SDA_A
B_GND
1
6
2
7
3
8
4
9
5
10
1
11
75Ω 1/16W
C6
56Ω 1/16W
75Ω 1/16W
56Ω 1/16W
R20
R23
R19
75Ω 1/16W
B
G
NC/3.6V
HSI
120 OHM BEAD -> 0 ohm
FB2
R32
1K 1/16W
R33
1K 1/16W
VSI
D7
MLL5232B 5.6V
D8
D9
1N4148
D10
MLL5232B 5.6V
1N4148
R34
C18
2.2KΩ 1/16W
33pF
HSYNC 7
VSYNC 7
7
7
R35
C19
2.2KΩ 1/16W
220pF -> 33pF
SDA_A
SCL_A
SDA_A
SCL_A
D45
LL5232B 5.6V 5%
7
7
VGA5V
VGA5V
HPDVGA
R130
100Ω 1/16W
R131
DET_VGA 7
D42
ESD
D46 D12
C20
100pF
ESD
LL5232B 5.6V 5%
SDA_D
SCL_D
SDA_D
SCL_D
LL5232B 5.6V 5%
D43
ESD
C82
100pF
D48 D41
C84
100pF
ESD
LL5232B 5.6V 5%
C83
0.1uF
LL5232B 5.6V 5%
DVI5V
DVI5V
HPDDVI
R36
10KΩ 1/16W
R37
100Ω 1/16W
DET_DVI 7
D11
D13
C22
3
ESD
C21
100pF
D47
10KΩ 1/16W
D40
D44
ESD
Q13
1
0.1uF
R141
MMBT3904L
2
LL5232B 5.6V 5%
4K7 -> 100K
HDCP
HPD_CTRL 5
FUNCTION
R39
1
10Ω 1/16W
R+ 7
2
DATA0+
CN8
L3
Shell
3
2
3
R48
HPDDVI
G- 7
B+ 7
3
QTC24CE/4P2R 0
DATA2DCLK+
DCLK-
10Ω 1/16W
10Ω 1/16W
L5
DATA0DATA0+
DCLK+
R50
10Ω 1/16W
R53
10Ω 1/16W
B-
7
CLK+ 7
L6
QTC24CE/4P2R 0
C23
C24
C25
C26
C27
C28
3
D19
BAV99
3
D18
BAV99
3
D17
BAV99
3
D16
BAV99
3
D15
BAV99
3
3
DVI-I
D14
BAV99
3
DCLKGND
GND
R46
DATA2+
2
DVI5V 6
R- 7
G+ 7
QTC24CE/4P2R 0
DATA1-
DVI5V
10Ω 1/16W
L4
DATA1DATA1+
DVI5V
10Ω 1/16W
2
25
26
27
28
29
4
RED
GRN
BLU
HS
GND
R44
1
RX0RX0+
GND
RX5RX5+
GND
RXC+
RXC-
17
18
19
20
21
22
23
24
R41
DATA1+
4
9
10
11
12
13
14
15
16
DATA0SCL_D
SDA_D
1
RX1RX1+
GND
RX3RX3+
5V
GND
HP
QTC24CE/4P2R 0
DATA2DATA2+
4
1
2
3
4
5
6
7
8
1
RX2RX2+
GND
RX4RX4+
SCL
SDA
VS
D20
BAV99
C29
D21
BAV99
C30
3
31
Shell
4
32
R58
10Ω 1/16W
CLK- 7
+5V
R59
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
10K
0.1uF
0.1uF
D22
3.6V
ViewSonic Corporation
Model
Title
Date
ViewSonic Corporation
74
Confidential - Do Not Copy
VG1930wm-3
INPUT
Rev:
VLCD
JP1
R60
VCC_TEST&ODCTRL
7 PA[0..9]
7 PB[0..9]
PA[0..9]
PB[0..9]
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
PA8
PA9
LVA3P
LVA3M
LVACKP
LVACKM
LVA2P
LVA2M
LVA1P
LVA1M
LVA0P
LVA0M
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PB8
PB9
LVB3P
LVB3M
LVBCKP
LVBCKM
LVB2P
LVB2M
LVB1P
LVB1M
LVB0P
LVB0M
RXE3+
RXE3RXEC+
RXECRXE2+
RXE2RXE1+
RXE1RXE0+
RXE0RXO3+
RXO3RXOC+
RXOCRXO2+
RXO2RXO1+
RXO1RXO0+
RXO0-
0/NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
JP2
LVB0M
RXO0LVB1M
RXO1LVB2M
RXO2LVBCKM
RXOCRXO3LVB3M
LVA0M
RXE0RXE1LVA1M
RXE2LVA2M
LVACKM
RXECRXE3LVA3M
VCC_TEST&ODCTRL
1
3
5
7
9
11
13
15
17
19
21
23
25
2
4
6
8
10
12
14
16
18
20
22
24
26
RXO0+
RXO1+
RXO2+
RXOC+
RXO3+
RXE0+
RXE1+
RXE2+
RXEC+
RXE3+
LVB0P
LVB1P
LVB2P
LVBCKP
LVB3P
LVA0P
LVA1P
LVA2P
LVACKP
LVA3P
HEADER 13X2
VLCD
VLCD 6
CON30
Modify 20050803: FPC LVDS
TC4
100uF/16V/NC
C31
0.1uF
VCC3.3
VCC3.3
6,7
R61
10K/NC
VCC_TEST&ODCTRL
FOR 19" FSC PANEL
VCC_TEST&ODCTRL 7
R62
0/NC
AGND
ViewSonic Corporation
VCC_TEST&ODCTRL is used for OVER DRIVE function control.
Model
Title
Date
ViewSonic Corporation
75
Confidential - Do Not Copy
VG1930wm-3
PANEL INTERFACE
Rev:
VCC1.8
VCC1.8 7
+5V
CN10
+5V
R67
10
9
8
7
6
5
4
3
2
1
10K
BL_ON
BL_ADJ
+5V
BL_ON
R68
C38
MLB-201209-0220P-N2
C85
+
TC20
220uF/16V
Q5
MMBT3904L
R70
1
0.1uF/NC
0.1uF
0/NC
VCTRL 7
R69
10K
3
L10 L1206
2
2
1
R71
50
4K7
on_BACKLIGHT 7
+ TC9
HEADER5X2
4.7uF/50V
+5V
+5V
C
F1
24V/5A/NC
B
+12V
L11 L1206
1
2
DIP
MLB-201209-0220P-N2/NC
+12V 3
TC21
220uF/16V/NC
R73
R72
C86
+
1N4148
1K
D26
10K
Q6
R76
CHT2907
2K
E
F2
24V/5A/DIP/NC
D25
1N4148
0.1uF/NC
R74
4K7
R75
3
BL_ADJ
C41
R78
R77
1
2
1uF
0/NC
Q7
4K7 -> 100K
100
Adj_BACKLIGHT 7
VCC3.3
MMBT3904L
VCC3.3 5,7
Recommond to used "Blue" parts circuit
for VCC1.8V if you want to suppoert DDC
function when system power off
DVI5V
4
VLCD
DVI5V
VGA5V 4
+5V
2
VLCD 5
R79
D28
10K
Q8
AO3401
R81
4K7
D27
SSM12L
BAT54C-GS08
3
0
3
7 on_Panel
R82
3,4,7 +5V
VCC_PANEL
R80
10K
1
VCC_PANEL
VGA5V
T0-263
Q9
1
+
0.1uF
U5
VCC5V
R83
TC10
3
10K
10uF/16V
For 15" 3.3V Panel
1084-33CM/NC
VO 2
VI
ADJ
C42
2
MMBT3904L
C43
4
VO
+ TC11
C44
100uF/16V/NC
0.1uF/NC
1
0.1uF/NC
VCC_3.3
03/21 MODIFY
L12 L1206
1
VCC_3.3
1
+5V
1
+12V
1
S3
L1206
S5
L1206
S12
L1206
2
MLB-201209-0220P-N2/NC
2
T0-252
U10
VCC_PANEL
2
C81
0.1uF
2
3
VIN
VOUT
2
1
ADJ
TAB
4
1117-33
VCC3.3
VCC3.3 5,7
+ TC22
C80
100uF/16V 0.1uF
ViewSonic Corporation
Model
Title
Date
ViewSonic Corporation
76
Confidential - Do Not Copy
VG1930wm-3
POWER (DC TO DC)
Rev:
VDDC
VCC3.3
VCC5V
R90
R91
4 SDA_D
4 SCL_D
R88
R89
10K
10K
3
4
6
7
9
10
12
13
100
1
4 B+
4 B4 G+
4 G4 R+
4 R4 CLK+
4 CLK-
100
100
R92
AVDD
390 1% 15
C58
1uF
REFP
25
REFM
8
7
3
4
0.1uF
TC19
VDD
HOLD#
WP#
VSS
SDO
CE#
SCK
SDI
2
1
6
5
37
38
39
40
84
R107
SDO
SCZ
SCK
SDI
PM25LV010
10uF/16V
RST
C63
0.22uF
10K
C64
22pF
C65
22pF
96
X1
14.318MHZ
34
VDDC
51
66
82
VDDC
VDDC
VDDC
32
49
56
75
VDDP
VDDP
VDDP
VDDP
24
AVDD_ADC
16
U8
C60
54
55
58
59
60
61
62
63
64
65
TSUM56AL/TSUM16AL
VCC3.3
+5V
LVA3P
LVA3M
LVACKP
LVACKM
LVA2P
LVA2M
LVA1P
LVA1M
LVA0P
LVA0M
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
PA8
PA9
XIN
67
68
69
70
71
72
73
74
77
78
NC
NC
NC
36
45
46
GPIO_P23
GPIO_P22
41
42
GPIO_P15/PWM0
PWM2/GPIO_P24
GPIO_P27/PWM1
GPIO_P12
PWM1/GPIO_P25
35
47
48
85
86
RSTN
GPIO_P00/SAR1
GPIO_P01/SAR2
GPIO_P02/SAR3
87
88
89
90
GPIO_P06
GPIO_P07
PWM0/GPIO_P26
GPIO_P13
GPIO_P14
GPIO_P16/PWM2
91
92
93
94
95
99
VCC3.3 FB6
PA[0..9]
10K
10K
+5V 3,4,6
5
VCC3.3
VCC3.3
VCC5V
R122
VCC3.3
R124
0/NC
10K
R123
C54
+
C55
0.1uF 0.1uF
5,6 VCC3.3
VPLL
600 OHM
TC18
10uF/16V
0.1uF
C57
+
0.1uF
100
R142
R95
20K
0.1uF
HPD_CTRL4
on_PANEL 6
on_BACKLIGHT 6
adj_BACKLIGHT 6
R101
R102
R104
100
100
100/NC
R105
R106
1K
1K
R98
330
R96
R97
10K
330
R100
R103
47
LED_G
47
Q10
MMBT3904L
1
C62
Q11
1
Volume 3
AUDIO_MUTE 3
MUTE
R99
10K
KEY1
KEY2
Revised by worry
BUZ_CPU
100 HDCP_SDA
R132
VCC3.3
VCC3.3
DET_VGA 4
POWER
100
0.1uF
MMBT3904L
LED_A
C61
0.1uF
DET_DVI 4
R133
0R HDCP_SCL
Revised by worry
0.1uF
R109
U9
10K
R111
R112
44
43
8
7
6
5
100
100
VCC
WP
SCL
SDA
A0
A1
A2
GND
1
2
3
4
C87
C68
0/NC
C_VCC
BUZZER
R125
10K
NC/0.1uF
U12
VCC3.3
A0
A1
A2
GND
VCC
WP
SCL
SDA
8
7
6
5
NC/24C04
HDCP Key (288Bytes)
Swap the pin
KEY2
D30
0.1uF
3.6V
KEY1
NC/100
NC/100
R138
NC/10K
R139 NC/0
HDCP_SCL
HDCP_SDA
JP?/NC1
1
2
3
R120
C69
0.1uF
AUTO
R135 NC/10K
R136
R137
DOWN
R119
1.5K
R134 NC/10K
3.9K
UP
C70
R140 NC/0
R117
3.9K
CN12
10K
POWER
12
LED_A 11
LED_G 10
DOWN
9
UP
8
MENU
7
AUTO
6
5
C_VCC 4
BUZ_ON 3
MUTE
2
ENHANCE 1
Revised by worry
VCC3.3
24C16
VCC3.3
2
3
C59
R116
BUZ_CPU
0/NC
VCC3.3 FB9
C56
TC17
10uF/16V
VCC3.3
0.1uF
R30
TC16
10uF/16V
VMPLL
1
2
3
4
2N3906/NC
BUZ_ON
BZ1
R94
VCC_TEST&ODCTRL
ENHANCE
R110
R121 3K3/NC
VDVI
600 OHM
0.1uF
600 OHM
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
MODE[0]
MODE[1]
1K/NC
1
5,6 VCC3.3
C53
+
10K
R118
Q12
VCC3.3 FB7
600 OHM
5,6 VCC3.3
+5V
2
5
11
29
33
50
57
76
79
83
R114
0.1uF
R93
10K
BYPASS
GPIO_P10/I2C_MCL
GPIO_P11/I2C_MDA
R113
C52
C66
C_VCC
1K/NC
C51
PB[0..9] 5
XOUT
0.1uF
R115
5,6 VCC3.3
C50
0.1uF 0.1uF 0.1uF
AVDD
VCC3.3 FB8
C67
52
53
PA[0..9] 5
PB[0..9]
R108
80
C49
+
VCC3.3
97
C48
600 OHM
TC14
10uF/16V
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PB8
PB9
C47
0.1uF 0.1uF 0.1uF
4.7uF/50V
VCTRL 6
TC15
10uF/16V
REXT
26
81
C46
TC13 +
FB5
VCTRL
LVB3P
LVB3M
LVBCKP
LVBCKM
LVB2P
LVB2M
LVB1P
LVB1M
LVB0P
LVB0M
600 OHM
600 OHM
+
RX2P
RX2N
RX1P
RX1N
RX0P
RX0N
RXCKP
RXCKN
DDCD_SDA
DDCD_SCL
VDDC
2
4 SDA_A
4 SCL_A
100
100
RIN0P
RIN0N
GIN0P
GIN0N
SOGIN0
BIN0P
BIN0N
HSYNC0
VSYNC0
DDCA_SDA/RS232_TX
DDCA_SCL/rs232_RX
6 VCC1.8
5,6 VCC3.3
0.1uF
3
JWT-A2001WV2-04/NC
R86
R87
23
22
20
19
21
18
17
27
28
30
31
4
RIN
4 GNDR
4
GIN
4 GNDG
4 SOG
4
BIN
4 GNDB
4 HSYNC
4 VSYNC
98
10K
1
2
3
4
AVDD_PLL
10K
U7
AVDD_MPLL
R85
AVDD_DVI
AVDD_DVI
CN11
R84
8
14
C45
VCC1.8 FB3
VDDP
FB4
2
VCC5V
VDDP
3
VDVI VMPLL AVDD
VPLL
D29
3.6V
1.5K
C16
MENU
C17
0.1uF
0.1uF
ViewSonic Corporation
Model
Title
Date
ViewSonic Corporation
77
Confidential - Do Not Copy
VG1930wm-3
SCALER
Rev:
9. PCB Layout Diagrams
ViewSonic Corporation
78
Confidential - Do Not Copy
VG1930wm-3
ViewSonic Corporation
79
Confidential - Do Not Copy
VG1930wm-3
ViewSonic Corporation
80
Confidential - Do Not Copy
VG1930wm-3
ViewSonic Corporation
81
Confidential - Do Not Copy
VG1930wm-3
ViewSonic Corporation
82
Confidential - Do Not Copy
VG1930wm-3
ViewSonic Corporation
83
Confidential - Do Not Copy
VG1930wm-3
10. Exploded Diagram and Exploded Parts List
EXPLODED PARTS LIST (VG1930WM-3)
ViewSonic Model Number: VS11419
Rev: 1a
Serial No. Prefix: QC6
ViewSonic Corporation
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
84
Confidential - Do Not Copy
VG1930wm-3
ViewSonic P/N
C-00008270
N/A
CB-00008111
HW-00008085
N/A
B-00008270
N/A
C-00008271
PL-00008091
CB-00008115
N/A
B-00008269
HW-00008084
HW-00008086
B-00008272
N/A
B-00008271
N/A
N/A
C-00008272
PL-00008090
N/A
Ref. P/N
151-MF1-KCIEUT9E-1H
705-590-G14CH
631-030-VG1930H
107-005-3082H
123-002-CA787DGH
899-VLG-19A2D-AH
123-B0D-19A2DH
151-MR1-KCIE9E-12H
107-010-3073H
631-013-VG1930-AH
121-001-19A2DH
860-AB0-190DTLB-PVH
107-005-3032H
108-305-4133H
899-40P-19A2DH
631-006-VG1930H
899-400-19A2DH
107-010-3071H
108-S10-4033H
154-001-19A2D9E-1H
151-MS0-HASTANDH
131-030-2110H
Description
BEZEL
PANEL
LVD LINE
SCREW
METAL COVER
AD BOARD
Metal Case
REAR COVER
SCREW
CONTROL WIRE
Support Bracket
POWER BOARD
SCREW
SCREW
POWER CONTROL BOARD
CONNECT WIRE
KEY BOARD
SCREW
SCREW
HINGE COVER
STAND ASSY
STAND OFF
Q'ty
1
1
1
5
1
1
1
1
7
1
1
1
5
5
1
1
1
2
4
1
1
1
PACKING PART LIST ( VG1930WM-3 )
ViewSonic Model Number: VS11419
Rev: 1a
Item ViewSonic P/N
Ref. P/N
1
N/A
VG1930wm-3
2
P-00008272
170-002-19V38H
3
P-00008273
160-00L-19A2DH
4
P-00008274
160-00R-19A2DH
5
N/A
005-001-19A2D-BH
N/A
600-181-3400ICH(by bom)
6
N/A
610-181-19GCH
7
8
CB-00008112
610-181-15GMFH
9
CB-00008114
631-U03-17V28H
N/A
002-M01-19A2D-AH
10
ViewSonic Corporation
85
Confidential - Do Not Copy
VG1930wm-3
Location
LCD Monitior
PE Foam Bag
cushion(LEFT)
cushion(Right)
Carton
Power cord(by bom)
DVI Cable
D-SUB Cable
Audio Cable
Menu
Q'ty
1
1
1
1
1
1
1
1
1
1
11. Recommended Spare Parts List
RECOMMENDED SPARE PARTS LIST (VG1930WM-3)
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
19
20
21
22
23
24
25
26
27
28
29
30
ViewSonic Model Number: VS11419
Rev: 1a
Serial No. Prefix: QC6
Description
Power Cord (U.K) RoHS
Accessories:
PC Board Assembly: Power Supply Board+Inverter Board Assy RoHS
Audio Control Board
[All PCBA]
Key Board
Power Supply Board
Front Panels
Cabinets:
Back Cover RoHS
[Front Panel, All
Hinge Cover RoHS
Covers, Base
Cables: [All Cables] Signal Cable (connect A.D Board) RoHS
Accessory Cable,D-Sub,BLACK JV-4777 30AWG RoHS
Accessory Cable,D-Sub,BLACK JCE RoHS
Audio Cable - 28AWG 180cm,Blank,JVE RoHS
Wire 13p 1.5-2.0 12p+2p*2 A0031460 CME ADD EMI
User Manual + CD Wizard RoHS
Documentation:
Safety label RoHS
Hardware: [Screw, Screw B3*5 RoHS
Screw B M3xL5 TP6 RoHS
Bracket, Hinge,
Screw M4 5*4 1010 steel ROHS
Washer]
Tape OPP 900*50*0.045mm
Miscellaneous:
Generic Foam
Packing Material:
Generic Box
[Box, Foam, Bags]
PE Bag 570*600*0.13 RoHS
Foam - Left
Foam - Right
Craft Box
Plastics: [Pedestal, Pedestal RoHS
Plate, Rubber Foot, B 3*10 TP4 E-Plate Ni RoHS
Panel protector film
Button, etc.]
ECR/ECN ViewSonic P/N
Ref. P/N
Location Universal number#
A-00008092
600-181-5000ICH
860-AB0-190DTLB-PVH
B-00008269
899-VLG-19A2D-AH
B-00008270
899-400-19A2DH
B-00008271
B-00008272
899-40P-19A2DH
C-00008270
151-MF1-KCIEUT9E-1H
C-00008271
151-MR1-KCIE9E-12H
C-00008272
154-001-19A2D9E-1H
631-030-VG1930H
CB-00008111
610-181-15GMFH
CB-00008112
610-181-15GMCH
CB-00008113
631-U03-17V28H
CB-00008114
631-013-VG1930-AH
CB-00008115
002-M01-19A2DH
DC-00008223
DC-00008224
153-001-19A2DH
107-005-3032H
HW-00008084
107-005-3082H
HW-00008085
108-305-4133H
HW-00008086
831-950-0301H
M-00008088
30833
P-00001347
20653
P-00002515
170-002-19V38H
P-00008272
160-00L-19A2DH
P-00008273
160-00R-19A2DH
P-00008274
P-00008275
005-001-19A2DH
PL-00008090
151-MS0-HASTANDH
107-010-3073H
PL-00008091
154-002-19A25H
PL-00008092
Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items.
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic
Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.
ViewSonic Corporation
86
Confidential - Do Not Copy
VG1930wm-3
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
ViewSonic Model Number: VS11419
Rev: 1a
Serial No. Prefix: QC6
ViewSonic P/N
DC-00008223
N/A
N/A
N/A
P-00008275
N/A
N/A
DC-00008224
PL-00008092
N/A
P-00008272
P-00008273
P-00008274
N/A
M-00008088
N/A
N/A
N/A
N/A
HW-00008084
HW-00008085
PL-00008091
HW-00008086
N/A
N/A
N/A
N/A
CB-00008112
CB-00008113
CB-00008115
B-00008269
B-00008270
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Ref. P/N
002-M01-19A2DH
003-401-19A2DH
003-H01-19A2DH
003-P01-17V27H
005-001-19A2DH
005-H01-KA17H
006-X01-KC17H
153-001-19A2DH
154-002-19A25H
170-000-PALLETH
170-002-19V38H
160-00L-19A2DH
160-00R-19A2DH
831-410-0600H
831-950-0301H
836-045-0500SH
841-001-19A2DH
705-590-G14CH
932-000-HDCPH
107-005-3032H
107-005-3082H
107-010-3073H
108-305-4133H
123-002-CA787DGH
123-B0D-19A2DH
154-M00-8090H
154-M00-DA985DGH
610-181-15GMFH
610-181-15GMCH
631-013-VG1930-AH
860-AB0-190DTLB-PVH
899-VLG-19A2D-AH
003-001-ADBIOSH
330-100-16253-WH
330-100-16253-JH
330-101-16253-WH
330-221-16203-W1H
330-2R2-50253-WH
330-4R7-50253-WH
409-005-0105BAH
483-302-2388H
485-415-9001TH
485-D25-R001TH
485-D25-R001ZH
504-A00-PT2300H
531-143-49US-2H
630-002-1009H
630-012-1009H
630-026-S2006H
631-003-VG1930-AH
852-VLG-19A2D-AH
200-100-VG1930-AH
281-031-39004H
281-031-47004H
281-031-49R94H
281-031-56R04H
281-031-75R04H
281-035-0R04H
281-035-0R04H
281-035-0R04H
281-035-1004H
281-035-1014H
63
N/A
281-035-1014H
64
N/A
281-035-1024H
65
N/A
281-035-1034H
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
281-035-1044H
281-035-1044H
281-035-1214H
281-035-1524H
281-035-2024H
281-035-2034H
281-035-2224H
281-035-2234H
281-035-3034H
281-035-3044H
281-035-3314H
281-035-3924H
281-035-4704H
281-035-4724H
285-056-B160CH
330-221-16203-W1H
381-101-032554H
381-102-035054H
381-220-032554H
ViewSonic Corporation
BOM LIST (VG1930WM-3)
Description
Location
Universal number#
19A2D MENU ASSY for TaiWan Jingpuze RoHS
19A2D Carton Label 合成紙 76.2*76.2 Sunway RoHS
19A2D Small Barcode Label 合成紙 RoHS Sunway
17V27 pallet Label white paper75*40 RoHS SUNWAY
19A2D Carton 瓦楞紙 RoHS
CORNER PROTECTOR PALLET
50mm*50mm*900mm RoHS
Corner Protector 50mm*50mm*1850mm RoHS
19A2D Safety label RoHS
19A25 Panel protector film XG-536 T=0.1 With_Print JsutEuter
PE Sheet LDPE Transparent 1850*1600mm RoHS
19V38 Pe Bag white LDPE 570*600*0.13 RoHS
19A2D Folyform-L EPS MingChan RoHS
19A2D Folyform-R EPS MingChan RoHS
ALL LCD PP Belt 10*0.8 Yellow 10KG RoHS
19V3F Tape OPP 900*50*0.045mm Symbio RoHS
VOLUBLE FILM 450mm*400m RoHS
19A2D PATTET Wooden RoHS
19"CMO-W PANEL(M190A1-L02) time:5ms RoHS
A HDCP Receiver key
SCREW B3*5 ISO E-PLATE WHITE Zn RoHS
SCREW B M3xL5 TP6 E-PLATE COLOR Zn RoHS
B 3*10 TP4 E-PLATE Ni RoHS
SCREW M4 5*4 1010 steel ROHS
CA787DG METAL COVER SECC=0.6t RoHS
19A2D METAL-CASE SECC T=1.0 DongFa/Wei yao RoHS
Mylar 80*90*0.3mm PET TRANSLUCENCY RoHS
DA985DG MAYLER 173*115*0.3mm PET
Accessory Cable,D-Sub,BLACK JV-4777 30AWG RoHS
Accessory Cable,D-Sub,BLACK JCE RoHS
Wire 13p 1.5-2.0 12p+2p*2 A0031460 CME ADD EMI RoHS
19"POWER+INVERTER MOUSE 3PIN C201 100uf/400V REV:A+ RoHS
PCBA,19A2D,A/D Board With Audio,REV:A RoHS
ALL CMO LCD BIOS Label poly 40*8mm RoHS
dispersing 10uF 16V 105C M TP 4*5 HUAWEI RoHS
TC14,TC15,TC10,TC16,TC17,TC18,
dispersing 10uf 16V 105C 4*5 jian long RoHS
EC 100uF 16V 105D M TP MI 009 6*5 FOR RoHS dispersing sh
TC22
EC.220uF/16V 105°C Φ6*11 dispersing shorting,huawei 180
TC20
2.2uF 50V 105D 4*5 RoHS 180D dispersing shorting,huawei Roh
TC33
EC 4.7uF 50V 105DEGREE MTP 4*5dispersing shorting,huawei RoH TC13,TC9
PHOE JACK GREEN+BLACK SCPRE RoHS
CN2
FEMALE180D 2.5P 254FH15 1S H8.50mm TY RoHS
CN10
D-SUB 15P 8.89 PC99 90D FEMALE1285-15S-004-98F RoHS TEKCOCN6
DVI-D/25P/90D(1241-440-054-32)TEKCON RoHS
CN8
DVI-D 25P 90D FEMALE NTK RoHS
AUDIO AMP IC FOR PTC PT2300 RoHS
U2
KTS QYSTAL 14.318MHZ. 20PF FOR RoHS
X1
BASE 2pin JWT A2001 PITCH=2mm Straight FOR RoHS
CN1,CN5
BASE 12P PITCH 2.0 FOR RoHS
CN12
BASE 2.0 26P /JWTA2006 STRAIGHFOR ROHS 2 ARRAY
JP2
Boand-in Wier 2.0 3p CME A0031459 RoHS
SMD,19A2D,A/D Board With Audido,REV:A RoHS
VSC VG1930 A/D B PCB,MST,TSUM56AWHL Rev:A RoHS
SMD 390ohm +-1% 1/10W 0603 RoHS
R92
SMD 470ohm +-1% 1/10W 0603 RoHS
R22
RES 49.9ohm 1% 1/10W 0603 SMD.RoHS
R71
RES 56.OΩ +-1% 0603 SMD RoHS
R19,R20,R21
RES 75 1% 1/10W 0603 SMD RoHS
R23,R24,R25
SMD 0ohm +-5% 1/10W 0603 RoHS
RA1
SMD 0ohm +-5% 1/10W 0603 RoHS
R39,R41,R44,R46,R48,R50
SMD 0ohm +-5% 1/10W 0603 RoHS
R81,RA2,R29
SMD,10ohm,+-5%,1/10W,0603 Green I
R53,R58
SMD 100ohm +-5% 1/10W 0603 RoHS
R142
R27,R28,R78,R86,R26,R87,R112,R9
SMD 100ohm +-5% 1/10W 0603 RoHS
0,R91,R95,R101,R102,R111
SMD 1K +-5% 1/10W 0603 Green I
R105,R106,R32,R33,R72
R108,R109,R110,R113,R114,R130,R
SMD 10K +-5% 1/10W 0603 Green I
36,R59,R67,R69,R107,R73,R17,R79,
R8,R80,R83,R84,R85,R88,R89,R93,
Chip Resistor SMD +-5% 0603 1/10W 100K ohm Green I
R3
Chip Resistor SMD +-5% 0603 1/10W 100K ohm Green I
R141
RES 120 5% 1/10W 0603 SMD
FB2
RES 1.5K 5% 1/10W 0603 SMD. RoHS
R119,R120
SMD,2K,+-5%,1/10W,0603,RoHS
R76,R12
SMD 20K +-5% 1/10W 0603 Green I RoHS
R2,R4,R94
SMD 2.2K +-5% 1/10W 0603 RoHS
R34,R35
SMD R 22K 0603 RoHS
R15
SMD 30Kohm +-5% 1/10W 0603 Green I
R1,R5
RES 300K 5% 1/10W 0603 SMD. RoHS
R126
RES 330 5% 1/10W 0603 SMD. FOR RoHS
R13,R97,R99
SMD 3.9K +-5% 1/10W 0603 RoHS
R116,R117
RES 47ohm 5% 1/10W 0603 SMD. FOR RoHS
R100,R103
SMD 4.7K +-5% 1/10W 0603 GreenII
R6,R10,R77,R70,R74,R82,R14
SMD VARISTOR 0603 5.5V 10pF RoHS HongDe
D11,D12,D40,D41,D43,D44
EC.220uF/16V 105°C Φ6*11 dispersing shorting,huawei 180
TC23
SMD CC NPO 100pF/25V 0603 +-5%RoHS
C20,C21,C82,C84
NPO 1000P/50V +-5% 0603 SMD RoHS
C9
SMD CC 22pF 25V NPO 0603. for RoHS
C65,C64
87
Confidential - Do Not Copy
Q'ty
1
1
1
0.032
1
0.125
0.125
1
1
0.032
1
1
1
0.002
0.0725
0.008
0.032
1
1
5
5
7
1
1
1
1
1
1
1
1
1
1
1
7
7
1
1
1
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
3
3
1
6
3
2
1
13
5
25
1
1
1
2
2
3
2
1
2
1
3
2
2
7
6
1
4
1
2
VG1930wm-3
Item
85
86
87
ViewSonic P/N
N/A
N/A
N/A
Ref. P/N
381-330-032554H
381-681-032554H
382-222-032564H
88
N/A
385-104-032584H
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
385-105-031684H
385-473-032584H
506-524-LC16-MH
506-525-L1005H
506-5PM-25LV010EH
506-CTS-M56AWHL-1H
506-RAS-1117-33H
518-02N-3904H
518-02N-3904-FH
518-02N-3904H
518-02N-3904-FH
518-02N-3906H
518-02N-3906-FH
518-FAO-3401H
518-TCH-2907AH
104
N/A
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
B-00008271
N/A
N/A
N/A
N/A
B-00008272
N/A
N/A
N/A
N/A
N/A
N/A
C-00008270
C-00008271
PL-00008090
C-00008272
N/A
N/A
N/A
N/A
N/A
N/A
N/A
A-00008092
N/A
N/A
CB-00008111
CB-00008114
N/A
N/A
N/A
N/A
528-200-BAV99-CH
528-2BA-T54CH
528-DSS-M12LH
528-R1N-4148H
529-350-03R6H
529-350-05R6H
780-103-300C04H
780-103-301C02H
780-103-601C07H
780-104-600C30H
780-104-600E30H
780-104-601C30H
780-107-121C50H
780-107-121J50H
899-400-19A2DH
200-K00-VG1930H
403-720-PTCFH
403-720-04TSCFAH
638-006-2611H
899-40P-19A2DH
200-K01-VG1930AH
403-720-02TSUYH
528-LPB-3227H
638-002-2611H
638-006-2611H
638-013-2611H
151-MF1-KCIEUT9E-1H
151-MR1-KCIE9E-12H
151-MS0-HASTANDH
154-001-19A2D9E-1H
107-010-3071H
108-S10-4033H
121-001-19A2DH
126-030-ALM7H
126-030-ALP1H
126-030-ALP6H
131-030-2110H
600-181-5000ICH
600-181-5000NCH
631-006-VG1930H
631-030-VG1930H
631-U03-17V28H
631-U03-17V28CH
831-B10-01013-ALZH
831-B10-3502-ALZH
831-B14-3502-ALZH
ViewSonic Corporation
Description
NPO 33PF/25V +-5% 0603 SMD RoHS
SMD CC 680pF 25V NP0 0603 RoHS
SMD CC 2200pF/25V X7R 0603. RoHS
Location
Universal number# Q'ty
2
C18,C19
2
C88,C89
1
C63
C1,C13,C14,C15,C16,C17,C22,C23,
C24,C25,C26,C27,C28,C29,C30,C31,
SMD CC Y5V 0.1uF/25V -20%~+80%0603 RoHS
C42,C45,C46,C47,C48,C3,C49,C85,
C50,C51,C52,C53,C54,C55,C56,C57,
45
C59,C60,C61,C62,C66,C67,C68,C69,
Y5V 1uF/16V +80-20% 0603. for RoHS
4
C2,C4,C41,C58
Y5V 0.047u/25V +80%-20% 0603for RoHS
6
C6,C7,C8,C10,C11,C12
EEPROM,24LC16BT-I/SNG S08 RoHSMicrochip
1
U9
MX25L1005 FLASH IC 1M 33Mhz RoHS
1
U8
PMC SPI FLASH 25LV010E RoHS
1
MSTAR TSUM56AWHL-LF-1 For RoHS
1
U7
LDO AS1117L 3.3V SOT-223 A1 RoHS
1
U10
TR NPN PMBS3904 40V 100mA SOT-23 RoHS PHILIPS
7
Q1,Q4,Q5,Q7,Q9,Q10,Q11
TR NPN MMBT3904LT1 40V 100mA SOT HM RoHS
7
TR NPN PMBS3904 40V 100mA SOT-23 RoHS PHILIPS
1
Q13
TR NPN MMBT3904LT1 40V 100mA SOT HM RoHS
1
TR PNP PMBS3906 40V 100mA SOT-23 RoHS PHILIPS
1
Q12
TR PNP MMBT3906LT1 40V 100mA SOT23 HM RoHS
1
Transistor P-MOS,SOT-23,AO3401,-30V/-4.2A AO RoHS
1
Q8
Transistor CHT2907A SOT-23 Chenmko RoHS
1
Q6
D1,D2,D3,D14,D15,D16,D17,D18,D
Switching Diode,BAV99,SOT-23 PHILIPS RoHS
11
19,D20,D21
SMD DIODE BAT54C SOT23.FOR RoHS
1
D27
schottky barrier 20~40V 1A D0-214AC SSM14LPT Chenmko RoHS
1
D28
DIODE 1N4148 SOT-34 SMD. for RoHS
4
D8,D10,D26,D25
ZENER BZT52C3V6 3.6V SOD123 Chang dian RoHS
3
D22,D29,D30
SMD ZENER 5.6V BZT52C5V6 Changdian RoHS
4
D9,D7,D13,D42
BEAD 30ohm 400mA 0603 CHILISINRoHS
3
L17,L18,L19
BEAD SMD 300ohm,200mA,+-25% CHILISIN RoHS
4
L13,L14,L15,L16
BEAD SMD 600ohm/1A,0603 +-25% CHILISIN RoHS
1
FB12
SMD BEAD 0805 60Ω/100MHz 3A CHILISIN FOR RoHS
2
L1,L2
SMD BEAD 0805 60Ω/100MHz 3A FOR ROHS
2
SMD BEAD 600ohm 3A 0805
100MHZ RoHS CHILISIN
8
FB3,FB4,FB5,FB6,FB7,FB8,FB9,FB
BEAD SMD 120ohm/5A 1206
CHILISIN RoHS
2
S5,L10
BEAD 120ohm 1206 5A 1206 Jantek FOR RoHS
2
PCBA,Control Key Board 19A2D(VG1930WM),RoHS
1
VSC VG1930wm CONTROL KEY PCB RoHS
1
SMD TACT SW SIDE KEY PTCF ALTA RoHS
5
SW2,SW3,SW4,SW5,SW6
SMD TACT SW SIDE KEYTSCF-31C HUA-JIE RoHS 180gf
5
SW2,SW3,SW4,SW5,SW6
SMD Wafer P1.5 6P 90D
5W1.2611B ARC RoHS
1
CN5
PCBA,Power Key Board 19A2D(VG1930WM),RoHS
1
VSC VG1930wm Power Control KeyPCB REV:A RoHS
1
SMD TACT SW 180D TSUY-2SL HUA-JIE RoHS
1
SW1
SMD KED KPB-3227SYKQBCC (V1) BLU/Org KINGBRIGHT
1
D1
SMD Wafer P1.5 2P 90D
5W1.2611B ARC RoHS
2
CN2,CN3
SMD Wafer P1.5 6P 90D
5W1.2611B ARC RoHS
1
CN4
SMD Wafer P1.5 13Pin 90D 5W1.2611B ARC RoHS
1
CN1
19A2D BEZEL ASS'Y UT+9E ABS-PA757 VSC+ENERGY STAR Fuking
1
19A2D Rear ASS'Y EM-009E ABS-PA757 Black Fuking RoHS
1
19A2D HASTAND RoHS
1
19A2D Hing Cover EM-009E ABS HG Guan Yi RoHS
1
SCREW B-Head 3.0*10 BLK RoHS
2
SCREW M4*10 P=0.7 Ni-Plate Fe RoHS SHYE CHing
4
19A2D SUPPORT PLATE SECC T=1.0 DongFa RoHS
1
C9 insulating film AL FOIL 70*30mm EMI FOR RoHS
1
AL FOIL 80*30mm RoHS
1
AL FOIL 50*30mm RoHS
1
signal cable Hex head screw 3.0 mm L=12mm RoHS
4
P/C SP-60/IS-14,Black,U.K.,1.8M,I-sheng RoHS
1
P/C LP-60L,H05VV-F,LS-60,Black1.8M,Linetek,RoHS
1
Wier 6P1.5 A0031461 CME RoHS
1
LVDS 30P A0031458 CME RoHS
1
17V28 AUDIO CABLE A170E1-H01 28AWG 180cm,Blank,JVE RoHS
1
Audio cable 28AWG 180cm Black RoHS JCE
1
AL CONDUCTIVE FOAM W10*H13*L10mm ZONGCHEN ROHS
1
AL CONDUCTIVE FOAM L40*W14*H2 mm ZONGCHEN ROHS
1
1
AL CONDUCTIVE FOAM L25*W14*H2 mm ALGK RoHS
88
Confidential - Do Not Copy
VG1930wm-3
* Reader’s Response*
Dear Readers:
Thank you in advance for your feedback on our Service Manual, which allows continuous improvement
of our products. We would appreciate your completion of the Assessment Matrix below, for return to
ViewSonic Corporation.
Assessment
A. What do you think about the content of this Service Manual?
Unit
Excellent
Good
Fair
Bad
1. Precautions and Safety Notices
2. Specification
3. Front Panel Function Control Description
4. Circuit Description
5. Adjustment Procedure
6. Troubleshooting Flow Chart
7. Recommended Spare Parts List
8. Exploded Diagram and Exploded Parts List
9. Block Diagrams
10. Schematic Diagrams
11.PCB Layout Diagrams
B. Are you satisfied with this Service Manual?
Item
Excellent
Good
Fair
Bad
1. Service Manual Content
2. Service Manual Layout
3. The form and listing
C. Do you have any other opinions or suggestions regarding this service manual?
Reader’s basic dada:
Name:
Title:
Company:
Add:
Tel:
Fax:
E-mail:
After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile
1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes
(marc.maupin@viewsonic.com)
ViewSonic Corporation
89
Confidential - Do Not Copy
VG1930wm-3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising