Clarion | BD316 | Owner`s manual | Clarion BD316 Owner`s manual

Clarion BD316 Owner`s manual
Owner’s manual
Mode d’emploi
Manual de instrucciones
■ Contents
English
■ Table des matières
Français
1. PRÉCAUTIONS.........................................................17
2. COMMANDES.............................................................3
3. NOMENCLATURE DES TOUCHES .........................18
4. CARACTÉRISTIQUES..............................................19
5. MANIPULATION DES DISQUES COMPACTS ........20
6. CLAVIER DE COMMANDE AMOVIBLE (DCP) .......21
7. TÉLÉCOMMANDE....................................................22
8. FONCTIONNEMENT.................................................24
9. DÉPISTAGE DES PANNES ......................................28
10.AFFICHAGE DES ERREURS...................................29
11.SPÉCIFICATIONS.....................................................30
BD316
AM/FM CD PLAYER
•
RADIO AM/FM-LECTEUR CD
•
RADIO AM/FM Y REPRODUCTOR CD
1. When the inside of the car is very cold and
the player is used soon after switching on
the heater, moisture may form on the disc
or the optical parts of the player and proper
playback may not be possible. If moisture
forms on the disc, wipe it off with a soft
cloth. If moisture forms on the optical parts
of the player, do not use the player for about
one hour and the condensation will disappear naturally to allow normal operation.
2. Driving on extremely bumpy roads which
cause severe vibration may cause the
sound to skip.
3. This unit uses a precision mechanism.
Even in the event that trouble arises, never
open the case, disassemble the unit, or
lubricate the rotating parts.
CAUTION
USE OF CONTROLS, ADJUSTMENTS, OR PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN, MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
THE COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE
EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL.
MODEL
DRX5675
12V
GROUND
AM 530-1710kHz/FM 87.9-107.9MHz
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
■ Índice
Español
1. PRECAUCIONES......................................................31
2. CONTROLES ..............................................................3
3. NOMENCLATURA DE LOS BOTONES ...................32
4. CARACTERÍSTICAS ................................................33
5. MANEJO DE LOS DISCOS COMPACTOS ..............34
6. PANEL DE CONTROL DESMONTABLE (DCP) ......35
7. CONTROLADOR REMOTO.........................................36
8. OPERACIÓN .............................................................38
9. SOLUCIÓN DE PROBLEMAS..................................42
10.INDICACIONES DE ERROR ....................................43
11.ESPECIFICACIONES ...............................................44
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off
and on, the user is encouraged to consult the
dealer or an experienced radio/TV technician
for help.
THIS PRODUCTION COMPLIES WITH DHHS RULES 21 CFR
SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE.
CLARION CO.,LTD.
50 KAMITODA,TODA-SHI,SAITAMA-KEN,JAPAN
Bottom View of Source Unit
MANUFACTURED:
SERIAL No.
PE-2310B
286- 324-00
Clarion Co.,Ltd.
MADE IN CHINA
INFORMATION FOR USERS:
CHANGES OR MODIFICATIONS TO THIS PRODUCT WILL VOID THE WARRANTY AND WILL
VIOLATE FCC APPROVAL.
Clarion Co., Ltd.
2000/1 (D • C)
All Rights Reserved. Copyright © 2001: Clarion Co., Ltd.
Printed in China / Imprimé en Chine / Impreso en China
PE-2394B
280-7619-00
Be sure to unfold and read the next page.
Veuillez déployer et vous référer à la page suivante.
Cerciórese de desplegar y de leer la página siguiente.
BD316
2
English
1. PRECAUTIONS...........................................................2
2. CONTROLS.................................................................3
3. BUTTON TERMINOLOGY ..........................................4
4. FEATURES..................................................................5
5. HANDLING COMPACT DISCS...................................6
6. DCP (Detachable Control Panel) ..............................7
7. REMOTE CONTROLL ................................................8
8. OPERATION..............................................................10
9. TROUBLESHOOTING ..............................................14
10.ERROR DISPLAYS ...................................................15
11.SPECIFICATIONS.....................................................16
1. PRECAUTIONS
2. CONTROLS / COMMANDES / CONTROLES
3. BUTTON TERMINOLOGY
Note:
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.
Remarque: Veuillez déployer cette page et vous référer aux schémas quand vous lisez chaque chapitre.
Nota: Cuando lea los capítulos, despliegue esta página y consulte los diagramas.
• Be sure to read this chapter referring to the front diagrams of chapter 2. CONTROLS on page 3 (unfold).
1 DCP Release Button
SOURCE UNIT / APPAREIL PILOTE / UNIDAD FUENTE
1
2
3
CD Insertion Slot
Fente d’insertion de CD
Ranura de inserción del disco compacto
2 A-M (Audio Mode) Button
4 5
LD (Loudness) Button
3 POWER Button
FNC (Function) Button
English
English
4 Eject (
) Button
5 ISR (Instant Station Recall) Button
6 DISP (Display) Button
7 RDM (Random) Button
%$
#
@!
0
987
6
8 RPT (Repeat) Button
9 SCN (Scan) Button
Français
PS/AS (Preset Scan/Auto Store) Button
0 Preset Buttons (1 to 6)
DISPLAY
AFFICHEUR
VISUALIZADOR
! Z-EHCR (Z-enhancer) Button
@ BND (Band) Button
TOP (Top Play) Button
# SRCH (Search) Left and Right (
$ Rotary Knob
Español
% Play/Pause (
MUTE Button
3
BD316
280-7619-00
4
BD316
) Button
and
) Buttons
4. FEATURES
■ Rotary Encoder Volume Control
■ DIN Chassis with Detachable Control Panel
■ Z-Enhancer with 3 Mode Sound Selector
■
®
FM Reception System
■ AM/FM Bands-1 AM, 3 FM/18 FM/6 AM Touchbutton Memory
■ 8-Times Oversampling Digital Filter and Dual 1-Bit D/A Converters
■ Zero-Bit Detector Mute Circuit
■ Repeat/Random Play/Intro Music Scan
E glis
■ Multi-Color LC Display
■ 4-Channel RCA Line Level Output with Fader Control
■ 180 W (45 W × 4) Maximum Power Output
■ Infrared Remote Control
BD316
5
5. HANDLING COMPACT DISCS
This unit has been designed specifically for playback of compact discs bearing the
mark.
No other discs can be played.
Note on Compact Discs
Never stick labels on the surface of the compact
disc or mark the surface with a pencil or pen.
To remove the compact disc from its storage
case, press down on the center of the case and
lift the disc out, holding it carefully by the edges.
Removing the disc
No
Proper way to hold
the compact disc
English
Always handle the compact disc by the edges.
Never touch the surface.
Do not use any solvents such as commercially
available cleaners, anti-static spray, or thinner to
clean compact discs.
No
To remove fingermarks and dust, use a soft
cloth, and wipe in a straight line from the center
of the compact disc to the circumference.
No
Do not use compact discs that have large
scratches, are misshapen, or cracked, etc. Use
of such discs will cause misoperation or damage.
No
New discs may have some roughness around
the edges. The unit may not work or the sound
may skip if such discs are used. Use a ball-point
pen, etc. to remove roughness from the edge of
the disc.
Ball-point pen
Roughness
Do not expose compact discs to direct sunlight
or any heat source.
No
Note:
• Do not use commercially available CD protection sheets or discs equipped with stabilizers, etc. These
may get caught in the internal mechanism and damage the disc.
6
BD316
6. DCP (Detachable Control Panel)
The control panel can be detached to prevent
theft. When detaching the control panel, store it
in the included DCP case to prevent scratches.
We recommend taking the detachable control
panel with you when leaving the car.
Removing the DCP
1. Turn off the power.
2. Press the DCP Release button 1.
DCP Release button 1
CAUTION
DCP Rear Panel
Source Unit Front
DCP
connector
Source unit connector
* The DCP is unlocked.
3. Remove the DCP.
Note:
• If the DCP is dirty, wipe off with a soft, dry cloth only.
Attaching the DCP
Insert the DCP into the right side of the source
unit and press the left side to lock it.
CAUTION
Do not insert the DCP from the left side. Doing so
may damage it.
2.
DCP
1.
Storing the DCP in the DCP Case
Hold the DCP, in the orientation as shown in the
figure below, and put it into the supplied DCP
case. (Ensure the DCP is in the correct orientation.)
DCP
DCP case
BD316
7
E glis
• The DCP can easily be damaged by shocks. After
removing it, place it in a protective case and be
careful not to drop it or subject it to strong shocks.
• When the release button is pressed and the DCP is
unlocked, the car’s vibrations may cause it to fall.
To prevent damage to the DCP, always store it in a
protective case after detaching it.
• The rear connector that connects the source unit
and the DCP is an extremely important part. Be
careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.
7. REMOTE CONTROL
Receiver for remote control unit
Operating range: 30° in all directions
English
Remote Control Unit
¥
*
Signal transmitter
)
(
&
™
¡
£
¢
§
∞
Inserting the Batteries
1. Turn the remote control unit over, then slide
the rear cover in the direction of the arrow.
2. Insert the AA (UM-3/1.5 V) batteries that
came with the remote control unit facing in
the directions shown in the figure, then close
the rear cover.
AA (UM-3/1.5 V)
Batteries
Notes:
Using batteries improperly can cause them to explode.
Take note of the following points:
• When replacing batteries, replace both batteries with
new ones.
• Do not short-circuit, disassemble or heat batteries.
• Do not dispose of batteries into fire or flames.
• Dispose of spent batteries properly.
8
BD316
Rear cover
Rear side
Functions of Remote Control Unit Buttons
Mode
Radio
Button
CD
¥ FUNC
Turns power on and off. When pressed and held for 1 second: Turns power off.
Switches between radio and CD.
& BAND
DISC UP
PROG
TOP
Switches reception band.
* VOLUME
Increases and decreases volume (in all modes).
( SEARCH
Moves preset channels up and down.
Moves tracks up and down.
When pressed and held for 1 second:
Fast-forward/fast-backward.
) PLAY/PAUSE
Turns mute on and off.
Switches between playback and pause.
¡ MUTE
Turns mute on and off.
Switches between playback and pause.
™ ISR
Recalls ISR radio station in memory.
Press and hold for more than 2 seconds: Stores current station into ISR memory
(radio mode only).
£ DISP
Switches among main display, sub display and clock display.
¢ SCAN
PS/AS
Preset scan.
When pressed and held for 2 seconds:
Auto store.
Scan play.
∞ RPT
BLS
No function.
Repeat play.
§ RDM
MONI
No function.
Random play.
Plays the first track.
Top play.
E glis
* Some of the corresponding buttons on the source unit and remote control unit have different functions.
BD316
9
8. OPERATION
Note:
• Be sure to read this chapter referring to the front diagrams of chapter 2. CONTROLS on page 3 (unfold).
Basic Operations
CAUTION
When this unit is turned on, starting and stopping the engine of a car with its volume raised
to the maximum level may harm your hearing.
Be careful about adjusting the volume.
English
Turning ON the Power and Adjusting
the Volume
Adjusting the Treble
1) Press A-M button 2 and select “TREB”.
2) Turning the Rotary knob $ clockwise emphasizes the treble; turning it counterclockwise
attenuates the treble.
* The
factory default setting is “0”. (Adjustment
range: –6 to +6)
3) When the adjustment is complete, press A-M
button 2 several times until the function
mode is reached.
1) Press the POWER button 3.
* To
turn off the power, press the POWER button
3 for 1 second or longer.
2) Press the FNC button 3 and select another
operation mode. Every time the FNC button
3 is pressed, the display changes the operation mode as:
Radio ➜ CD ➜ Radio
factory default setting is “0”. (Adjustment
range: L9 to R9)
• The operation mode not connected to the unit will not
be selected.
If the CD mode is selected when no disc is inserted,
the display flashes “ NO DISC”.
3) Turning the Rotary knob $ clockwise
increases the volume; turning it counterclockwise decreases the volume.
* The volume level is from 0 (minimum) to 33 (maximum).
Audio Mode Adjustments
Press the A-M button 2 to select the adjustment
mode. The mode switches as follows each time
the A-M button is pressed:
BASS ➜ TREB ➜ BAL ➜ FAD ➜ Previous
mode
Adjusting the Bass
1) Press A-M button 2 and select “BASS”.
2) Turning the Rotary knob $ clockwise emphasizes the bass; turning it counterclockwise
attenuates the bass.
* The
factory default setting is “0”. (Adjustment
range: –6 to +6)
3) When the adjustment is complete, press A-M
button 2 several times until the function
mode is reached.
10
1) Press A-M button 2 and select “BAL”.
2) Turning the Rotary knob $ clockwise emphasizes the sound from the right speaker; turning it counterclockwise emphasizes the sound
from the left speaker.
* The
Notes:
•
Adjusting the Balance
BD316
3) When the adjustment is complete, press A-M
button 2 several times until the function
mode is reached.
Adjusting the Fader
1) Press A-M button 2 and select “FAD”.
2) Turning the Rotary knob $ clockwise emphasizes the sound from the front speakers; turning it counterclockwise emphasizes the sound
from the rear speakers.
* The
factory default setting is “0”. (Adjustment
range: F9 to R9)
3) When the adjustment is complete, press A-M
button 2 several times until the function
mode is reached.
Setting the Z-enhancer
Radio Mode Operations
This unit comes with three types of sound tone
effects stored in memory. Select the one you prefer.
FM Reception
* The factory default setting is “Z-EHCR OFF”.
Loudness Effect
In order to turn on/off the loudness effect, use
the LD button 2 for 2 seconds or longer. Every
time the LD button 2 is pressed and held for 1
second or longer, the loudness effect switches
on and off.
* When the loudness effect is on, the display will show
“LD”.
®
For enhanced FM performance the
tuner includes signal actuated stereo control and
Multipath noise reduction circuits.
Listening to the Radio
1) Press the FNC button 3 to select the radio
mode, then the radio will be on.
2) To select a preset band, press the BND button @, then select one of the preset bands
such as FM1, FM2, FM3, or AM. Every time
the BND button @ is pressed, the display will
change as:
FM1 ➜ FM2 ➜ FM3 ➜ AM ➜ FM1
3) Press the SRCH Left/Right button #, then
the station at which there is a broadcast will
be selected (Seek selection).
Mute
Every time the DISP button 6 is pressed, the
display will change between the operation mode
and the clock display.
Use this function to turn off the sound immediately.
Press the MUTE button %. The sound turns off
and “MUTE” appears on the display. Press the
MUTE button again to cancel the mute mode.
Setting the Clock
Manual Tuning
1) Press the DISP button 6 to display the clock
display.
2) Press and hold the DISP button 6 for 1 second or longer.
3) Press the SRCH Left button #, then set the
current hour.
4) Press the SRCH Right button #, then set the
current minute.
5) Press the DISP button 6, then the clock is
set.
1) Press the BND button @, then select FM1,
FM2, FM3 or AM.
2) Press and hold the BND button @ for 1 second or longer, then the display will show
“MANU”, which means that a manual selection function is on.
3) Press the SRCH Left/Right button # and
select the right station.
Notes:
1) Press the BND button @, then select FM1,
FM2, FM3 or AM.
2) If the “MANU” on the display is on, press and
hold the BND button @ for 1 second or
longer. When the “MANU” display is off, the
Seek Selection function is on.
3) Press the SRCH Left/Right button #, then
when it selects the station in which there is a
broadcast, it automatically stops.
Switching the Clock Display
• If
•
you select another operation mode while you are
setting the clock, the clock setting operation will be
canceled.
If you remove the vehicle’s battery for a check or
repair, the clock will be reset, so you must set it again.
Seek Tuning
BD316
11
E glis
Each time you press Z-EHCR button !, the
tone effect changes in the following order.
“Z-ENHANCER 1” ➜ “Z-ENHANCER 2” ➜
“Z-ENHANCER 3” ➜ “Z-EHCR OFF” ➜
“Z-ENHANCER 1”...
• Z-ENHANCER 1: bass emphasized
• Z-ENHANCER 2: treble emphasized
• Z-ENHANCER 3: bass and treble emphasized
• Z-EHCR OFF: no sound effect
Preset Memory Function
Preset Memory Function can store up to 24 stations: six stations for each of FM1, FM2, FM3
and AM.
Note:
• When
the present memory function is used, all the
content of the memory will be erased.
English
Manual memory function
1) Press the BND button @, and select the
band you want to store in the memory.
2) Press the SRCH Left/Right button # then
select the station you want to store in the
memory.
3) Press and hold the Preset button 0 for 2
seconds or longer, then the station will be
stored in the memory.
Auto store function (Automatic Station Store)
1) Press the BND button @, then select the
band you want to store in the memory.
2) Press and hold the AS button 9 for 2 seconds or longer, then the station at which the
reception is the strongest will be automatically stored in the memory.
3) Press and hold the ISR button 5 for 2 seconds or longer.
Recalling ISR
Press the ISR button 5 then the display will
show “ISR”, then the radio station previously
memorized will be selected. Press the ISR button 5 again to disengage the unit from the
Recalling ISR function.
Area Change
Use this function when you are using the car
stereo anywhere outside the U.S.
Switchable frequency spacing
This car stereo is initially set to tune in frequency intervals of 10 kHz for AM and 200 kHz for
FM, the standard calibrations in the U.S. When
using the unit outside the U.S., use the following
procedure to switch the frequency range.
The table below lists the frequency specifications for the U.S. and other countries.
Initial Setting New Setting
(U.S. standard) (outside U.S.)
10 kHz
9 kHz
Frequency
range
530 to
1,710 kHz
531 to
1,629 kHz
Frequency
spacing
200 kHz
50 kHz
Frequency
range
87.9 to
107.9 MHz
87.5 to
108 MHz
AM
Note:
• When the number of stations stored is less than six,
the previous content of the memory for each direct
button will be retained.
Preset Scanning (Preset Station Scan)
When the PS button 9 is pressed, the preset
memory numbers flash and the stations are
tuned in for 7 seconds each in the order in which
they were stored. Press the PS button again to
cancel the preset scanning mode.
Instant Station Recall (ISR)
With this function, a specific radio station can be
recalled from any mode.
ISR memory
1) Press the FNC button 3, then select the
radio mode.
2) Select the radio station which you want to
store in the memory.
12
Frequency
spacing
BD316
FM
Switching the area change
Outside U.S. (New Setting)
While pressing the BND button @, press the
SRCH Left button #, then “outside U.S.” will be
selected.
Inside U.S. standard (Initial Setting)
While pressing the BND button @, press the
SRCH Right button #, then the “U.S. standard”
will be selected.
CD Mode Operations
Loading a Disc
Insert the disc into the CD insertion slot with its
label side up, then the CD will start playing.
For 5-inch (12 cm) CD
For 3-inch (8 cm) single CD
Selecting Tracks (songs)
Press the SRCH Left/Right button #.
: Playback will start from the next track.
: Playback will start from the beginning of
the track currently playing. When this
button is pressed again, the CD will play
from the previous track.
Fast-Forward and Fast-Backward
* When inserting a single CD (3”(8 cm)), insert it from
the center of the slot.
* When inserting a single CD (3”(8 cm)), do not connect an adapter.
* Pressing the SRCH Left/Right button for 1 second or
longer will move forward or backward 5 times faster
than normal play, and pressing it for 3 seconds or
longer will do the operation 30 times faster.
Scan Play (Intro Music Scan)
Notes:
Press the SCN button 9, then the display
shows “SCN”, then the CD will play the first 10
seconds of each track of the whole disc. Press
the SCN button 9 again to disengage the unit
from scan play.
• Some
CDs recorded in CD-R mode may not be
usable.
Even when recorded in CD-R/W mode, some CDs
may not be usable.
* A scan play will start from the track following the one
Listening to the Disc already Inserted
Press the FNC button 3 to select the CD mode,
the CD will start playing.
Press the RPT button 8, then the display shows
“RPT”, then the track currently playing will be
played repeatedly. Press the RPT button 8
again to disengage the unit from repeat play.
Stopping (pausing) Playback
Random Play
Press the Play/Pause button %.
Press the Play/Pause button % again to resume
playback.
Press the RDM button 7, then the display will
show “RDM”, then the entire tracks on the disc
will be played at random. Press the RDM button
7 again to disengage the unit from random play.
* Press the DISP button 6, then the display will show
the play time.
•
currently playing.
Repeat Play
Ejecting the CD
Press the Eject button 4, then the CD will be
ejected.
Note:
• If the ejected CD is left as it is, it will be reloaded after
15 seconds. However, single CDs will not be
reloaded, so make sure to remove them.
Top Function
Press the TOP button @, then the CD will start
playing from the first song (track number 1).
BD316
13
E glis
Press and hold the SRCH Left/Right button #.
: To fast-forward
: To fast-backward
9. TROUBLESHOOTING
Problem
Cause
Solution
Fuse is blown.
Replace with a fuse of the same
amperage. If the fuse blows again,
consult your store of purchase.
Incorrect wiring.
Consult your store of purchase.
Compact disc cannot be
loaded.
Another compact disc is
already loaded.
Eject the compact disc before loading
the new one.
Sound skips or is noisy.
Compact disc is dirty.
Clean the compact disc with a soft
cloth.
Compact disc is heaviiy
scratched or warped.
Replace with a compact disc with no
scratches.
Sound is bad directly after
power is turned on.
Water droplets may form
on the internal lens when
the car is parked in a
humid place.
Let dry for about 1 hour with the
power on.
Nothing happens when
buttons are pressed.
Display is not accurate.
Microprocessor has
malfunctioned due to
noise, etc.
Turn off the power, then press the
DCP Release button 1 and remove
the DCP.
Press the reset button for about 2
seconds with a thin rod.
Power does not turn on.
(No sound is produced.)
English
Reset button
DCP or source unit
connectors are dirty.
14
BD316
Wipe the dirt off with a soft cloth
moistened with cleaning alcohol.
10. ERROR DISPLAYS
■ To protect the system, this unit has been equipped with self diagnostic functions. If a fault
arises, a warning is issued by various error displays. Follow the corrective measures and
remove the fault.
Error Display
Corrective Measure
This error display indicates that a fault has arisen in the
mechanism of the source unit (for example, the disc cannot be
ejected).
➜ Check the source unit.
CD ER3
This error display indicates that the pickup focus is off because
of a scratched disc or some other factor during source unit play.
➜ Check the compact disc.
CD ER6
This indicates that the CD’s TOC (table of contents) cannot be
read, for example because the selected disc is upside-down.
BD316
15
E glis
CD ER2
11. SPECIFICATIONS
FM Tuner
General
Frequency Range: 87.9 MHz to 107.9 MHz
Usable Sensitivity: 11 dBf
50 dB Quieting Sensitivity: 17 dBf
Alternate Channel Selectivity: 75 dB
Stereo Separation (1 kHz): 35 dB
Frequency Response (±3 dB): 30 Hz to 15 kHz
Power Supply Voltage: 14.4 V DC (10.8 V to 15.6
V allowable), negative ground
Current Consumption: Less than 15 A
Speaker Impedance: 4 Ω (4 Ω to 8 Ω allowable)
Weight: 3.97 lb. (1.8 kg)
Dimensions:
7” (178 mm) Width × 2” (50 mm) Height ×
6-1/8” (155 mm) Depth
AM Tuner
CD Player
System: Compact disc audio system
Usable Discs: Compact disc
Frequency Response: 10 Hz to 20 kHz (±1 dB)
Signal-to-Noise Ratio: 100 dB (1 kHz) IHF-A
Dynamic Range: 95 dB (1 kHz)
7”
(178 mm)
2”
(50 mm)
7-3/8”
(188 mm)
2-1/4”
(58 mm)
6-1/8”
(155 mm)
English
Frequency Range: 530 kHz to 1,710 kHz
Usable Sensitivity: 25 µV
Notes:
Audio
Maximum Power Output:
180 W (45 W × 4 ch)
Continuous Average Power Output:
17 W × 4, into 4 Ω, 20 Hz to 20 kHz,1%THD
Bass Control Action (30 Hz): ±13 dB
Treble Control Action (10 kHz): ±10 dB
Line Output (with CD 1 kHz, 10 kΩ): 1.8 V
16
BD316
• Specifications comply with EIA Standards.
• Specifications and design are subject to change without notice for further improvement.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising