Bradley | TDB3108 | Specifications | Bradley TDB3108 Specifications

Bradley TDB3108 Specifications
Installation
TDB3108
Terreon 54" Circular Deep Bowl
Washfountain with Air Metering Valve
®
TDB3108
with Push Button Air Valve
Available in standard height,
juvenile height, and TAS height.
WF3208
Terreon Extra Height 54" Circular Classic
Washfountain with 9" Deep Bowl and Air
Metering Valve
®
Table of Contents
WF3208
with Push Button Air Valve
215-1471 Rev. F; ECN 13-00-001
© 2013 Bradley
Page 1 of 24 1/23/2013
Pre-Installation Information . . . . . . . . . . . . . . . . . . . . . . . . 2
Circular Washfountain Dimensions . . . . . . . . . . . . . . . . 3–4
Rough-In Specifications . . . . . . . . . . . . . . . . . . . . . . . 5–6
Installing the Drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Bowl/Pedestal Mounting and Assembly . . . . . . . . . . . . . . 8
Installing Drain Spud in Bowl . . . . . . . . . . . . . . . . . . . . . . 8
Air Metering Valve Assembly . . . . . . . . . . . . . . . . . . . 9-12
Valve and Tubing Connections . . . . . . . . . . . . . . . . . . . . 13
Adjust the Temperature . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cleaning and Maintenance . . . . . . . . . . . . . . . . . . . . 15-16
Soap Valve Parts List and Maintenance . . . . . . . . . . 17-18
Sprayhead Parts List and Troubleshooting . . . . . . . . . . . 19
Actuator Module Assembly Components . . . . . . . . . . . . 20
Metering Air Valve Maintenance . . . . . . . . . . . . . . . . . . . 20
Metering Air Valve Repair Kits and Troubleshooting . . . 21
Valve Assembly Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Vernatherm Parts List and Troubleshooting . . . . . . . 23–24
P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 800.BRADLEY (800.272.3539) FAX 262.251.5817
bradleycorp.com
TDB3108, WF3208
Installation
IMPORTANT!
Read this entire installation manual to ensure proper installation. When finished with the
installation, file this manual with the owner or maintenance department.
Installation
Packing List
IS
TH
SIDE
UP
•
•
•
•
Separate parts from packaging and make sure all parts are accounted for before discarding
any packaging material. If any parts are missing, do not begin installation until you obtain
the missing parts.
Make sure that all water supply lines have been flushed and then completely turned off
before beginning installation. Debris in supply lines can cause valves to malfunction.
Hardware supplied by installer must be appropriate for wall construction. Wall anchors used
must have a minimum pull-out rating of 1,000 lbs.
Product warranties may be found under “Product Information” on our web site
at www.bradleycorp.com.
Supplies Required by Installer
• (4) 1/2" lag bolts, screws or other fasteners to anchor washfountain pedestal
• 1" hot and cold water supply lines and fittings
• Reducing fittings and 1/2" nominal copper tubing supply lines for types with supplies from above
• Standard P-trap (vented trap supplied by Bradley when required)
• 2" drain lines and fittings
• 1-1/2" vent or tie pipe on fixtures vented through washfountain column
• Teflon tape or pipe dope
Pre-Installation Information
Terreon Material
®
The Washfountain is constructed of Terreon , a densified solid surface material composed of polyester resin. Terreon is resistant to
chemicals, stains, burns and impact. Surface damage can be easily repaired with everyday cleaners or fine-grit abrasives. Terreon
is NAHB certified to meet ANSI Z124.3, Z124.6 and ANSI/ICPA SS-1-2001.
®
Cylindrical air valve
The air valve pushbutton allows each user to activate an air metering valve (starting the flow of water) by pushing and releasing
the pushbutton. The air metering valve is factory-preset to run for 10 seconds and can be adjusted to run from 5-60 seconds.
2
1/23/2013Bradley • 215-1471 Rev. F; ECN 13-00-001
TDB3108, WF3208
Installation
Circular Washfountain Dimensions
Model TDB3108
Model TDB3108
54" Circular - side view
54" Circular with optional accessories - side view
Adjust to Towel Dispenser
Mounting Holes
54" (1372)
6"
(152)
47-1/4"
(1200)
43-3/4"
(1111)
34"
(864)
63-5/8"
(1616)
w/ soap
55-1/8"
(1400)
w/o soap
10"
(254)
23-1/2"
(597)
47-1/4"
(1200)
34"
(864)
55-3/4"
(1416)
19-1/2"
(495)
36" (914)
43-3/4"
(1111)
10"
(254)
23-1/2"
(597)
19-1/2"
(495)
Model TDB3108 is ADA Compliant
36" (914)
Optional equipment may not comply with all
ADA dimensional guidelines
54" (1372)
Model TDB3108 (Juvenile Height)
Model TDB3108 (Juvenile Height)
54" Circular - side view
54" Circular with optional accessories- side view
Adjust to Towel Dispenser
Mounting Holes
54" (1372)
6"
(152)
42-5/8"*
(1083)
59-1/8"*
(1502)
w/ soap
50-5/8"*
(1286)
w/o soap
39-1/8"*
(994)
10"*
30"*
(254)
(762)
23-1/2"*
(597)
19-1/2"
(495)
42-5/8"*
(1033)
51-1/4"*
(1303)
30"*
(762)
39-1/8"*
(994)
10"*
(254)
23-1/2"*
(597)
35-1/2" (902)
19-1/2"
(495)
35-1/2" (902)
* Add 2" (51) for TAS height unit
54" (1372)
Bradley • 215-1471 Rev. F; ECN 13-00-001
1/23/2013
3
TDB3108, WF3208
Installation
Circular Washfountain Dimensions
Model TDB3208
Model TDB3208
54" Circular - side view
54" Circular with optional accessories - side view
54" (1372)
Adjust to Towel Dispenser
Mounting Holes
6"
(152)
47-1/4"
(1200)
63-5/8"
(1616)
w/ soap
55-1/8"
(1400)
w/o soap
43-3/4"
(1111)
10"
34"
(254)
(864)
23-1/2"
(597)
55-3/4"
(1416)
19-1/2"
(495)
37-1/2" (953)
Model TDB3208 is not ADA Compliant
47-1/4"
(1200)
34"
(864)
43-3/4"
(1111)
10"
(254)
23-1/2"
(597)
19-1/2"
(495)
37-1/2" (953)
54" (1372)
4
1/23/2013Bradley • 215-1471 Rev. F; ECN 13-00-001
TDB3108, WF3208
Installation
Rough-In Specifications
Type A Drain
(mm)
Off-line vent with
supplies from below
1" NPT Supplies Through Floor,
Stub Up 2-1/2" (64) Above Floor
7-5/8" 7-5/8"
(194) (194)
Hot
Cold
2" NPT Drain
Through Floor,
Stub up 3" (76)
Above Floor
4"
(102)
54" (1372) Bowl
Supply lines for one to two
washfountains should be 1"; for three
washfountains 1-1/4". For more than
3 washfountains, pipe sizes should be
increased proportionately.
Type O Drain
(mm)
Off-line vent with
supplies from above
1" NPT Supplies From Above Must
Reduce to 1/2" Nominal Copper Tube on
These Centers to Pass Thru Washfountain
7/8"
(22)
1-1/4"
(32)
Hot
4"
(102)
54" (1372) Bowl
Bradley • 215-1471 Rev. F; ECN 13-00-001
7/8"
(22)
Cold
2" NPT Drain
Through Floor,
Stub Up 3" (76)
Above Floor
Supply lines for one to two
washfountains should be 1"; for three
washfountains 1-1/4". For more than
3 washfountains, pipe sizes should be
increased proportionately.
1/23/2013
5
TDB3108, WF3208
Installation
Rough-In Specifications
Type B Drain
(mm)
Centrally rising vent with
supplies from above
1" NPT Supplies From Above Must
Reduce to 1/2" Nominal Copper Tube on
These Centers to Pass Thru Washfountain
7/8"
(22)
7/8"
(22)
2" NPT Drain
Through Floor,
Stub Up 3" (76)
Above Floor
Hot
1-1/4"
(32)
Cold
1/2" NPT
Vent to
Ceiling
4"
(102)
Supply lines for one to two
washfountains should be 1"; for three
washfountains 1-1/4". For more than
3 washfountains, pipe sizes should be
increased proportionately.
54" (1372) Bowl
(mm)
Type H Drain
Centrally rising vent with
supplies from below
1" NPT Supplies Through Floor,
Stub Up 2-1/2" (64) Above Floor
7-5/8" 7-5/8"
(194) (194)
1-1/4"
(32)
Hot
2" NPT Drain:
Stub up 3" (76)
Above Floor
54" (1372) Bowl
6
Cold
4"
(102)
1/2" NPT
Vent to
Ceiling
Supply lines for one to two
washfountains should be 1"; for three
washfountains 1-1/4". For more than
3 washfountains, pipe sizes should be
increased proportionately.
1/23/2013Bradley • 215-1471 Rev. F; ECN 13-00-001
TDB3108, WF3208
Installation
1
Installing the Drain
A
Rough in supply and drain piping
as required for your installation.
B
Assemble the drain to the dimension
for the bowl you are installing.
All piping shown in dotted lines to be
supplied by installer.
Types B, H
Vent or Tie Pipe
(Supplied by
Installer)
2" NPT Coupling if Tie
Pipe is Not Required
(Supplied by Installer)
Vented Trap
(111-024)
B - See Table 1
Centerline of
Washfountain
Centerline of
Washfountain
4"
(102)
B - See Table 1
Vent or Tie Pipe
(Supplied by
Installer)
4"
(102)
Optional Tie Pipe
Bracket (S70-082)
Types A, O
B - See Table 1
Centerline of
Washfountain
See Rough-In information for
dimensions not shown.
4"
(102)
Types A, O with Tie
Pipe Bracket Option
Table 1 — “B” Trap Dimensions
Dim
Standard Height
Juvenile Height
TAS
B
23-3/8" (594mm)
22-1/2" (572mm)
24-1/2" (622mm)
Bradley • 215-1471 Rev. F; ECN 13-00-001
1/23/2013
7
TDB3108, WF3208
2
Installation
Bowl/Pedestal Mounting and Assembly
CAUTION! Bowl surface is very smooth.
Approximate weight of bowl is
190 pounds. Handle with Care!
A
Top View
Threaded
Rods (4)
Places
Floor Mounting
(4) Places
Position the pedestal making sure the
floor mounting holes (4) line up. Mark the
mounting-hole positions.
TAS OPTION: Place TAS spacer on floor
over the mounting holes. Place pedestal on
top of the spacer.
B
Secure pedestal to floor with suitable
fasteners, 1/2" anchors and bolts (supplied
by installer). Do not overtighten.
C
Using three or four people, carefully lift
bowl on to pedestal making sure drain
holes line up with floor drain and mate
thread rods with slotted holes in pedestal
using locator ribs.
D
3
A
Drain
Front View
Place Hands
Here When
Lifting Bowl
Place Hands
Here When
Lifting Bowl
Threaded Rod
(Secured by 1/4"
wing nut and
washer)
Locator Ribs
(4) Places
Using 1/4" wing nuts and washers, secure
bowl to pedestal in four places.
1/4" wing nuts
and washers
(4) Places
Installing Drain Spud in Bowl
Loosely attach the drain spud to the bowl
with the locknut and washer.
B TRAP OPTION: attach B trap to drain spud.
Seal between drain spud and drain hole with
plumber’s putty (supplied by installer).
Drain Pre-Pack
(S45-273)
Strainer (S45-067)
Spud (112-015)
Tie Pipe OPTION: attach tie pipe bracket to
drain spud.
B
Tighten the spud and lock nut against the
bowl.
Bowl
8
C
Secure the strainer to drain spud with the
screws provided.
D
Connect spud (or B Trap or Tie Pipe
Bracket) to drain.
Washer (142-068)
Locknut (161-021)
1/23/2013Bradley • 215-1471 Rev. F; ECN 13-00-001
TDB3108, WF3208
Installation
4a
Air Metering Valve Assembly for A Drain and O Drain Units
without Tie Pipe Option
A
B
Install hemmed end (not sharp end) of
support tube with gasket onto bowl.
Tie Rod Pre-Pack
Connect 1/2" supply tubing to sprayhead with
3/8" NPT to 1/2" tube connector and place
sprayhead onto support tube. Run the tubing
down through the support tube and connect
to valve tube connector.
Cover
Actuator
Module
Assembly
Coupling
Nut
Sprayhead
C
Place the upper tie bar (notched at both
corners of each end) on top of sprayhead.
Connect the longer tie rod to the 4-1/4" tie
rod using the coupling nut with hex head
set screws. Run the tie rod assembly down
through upper tie bar and secure from
underneath the bowl using lower tie bar (no
notches) and hex nut with socket head set
screw.
Tie Bar
Tie Rod
Supply Tube
Section View of
A/O Unit Assembly
Top Cover
(107-099 (A))
(107-179 (O))
Tie Rod Pre-Pack
(S45-1336)
Actuator Module
Assembly (S65-132)
Module Cover
(S04-083)
Nut
Tie Bar
Sprayhead
(S05-054)
Support Tube
STD (S57-005)
TAS/JUV (S57-006)
Tie Rod
(176-008A)
Drain
(S45-273)
Support
Tube Gasket
(125-011)
Pre-Pack
(S45-055)
Terreon Deep Bowl
(Part No. Varies with color
of bowl. Contact your local
Bradley Rep for assistance)
®
1/2" Supply
Tube
Access Panel
(186-1456)
Pedestal Assembly
(S17-242)
Valve Assembly
(S08-373)
A/O
(A shown)
Bradley • 215-1471 Rev. F; ECN 13-00-001
1/23/2013
9
TDB3108, WF3208
4a
D
Installation
Air Metering Valve Assembly for A Drain and O Drain Units
without Tie Pipe Option continued...
Place the actuator module assembly on top of
sprayhead. Rotate until actuator module locks in
with tie bar. Drop 1/8" diameter tube down to valve
assembly and connect to the air valve.
Skip to step F for units without soap.
Unit with "O" Drain and Actuator Module
Shown, Also Available with "A" Drain
Top
Cover
Soap
Dispenser
8-5/8" Tie Rod
E
F
For units with soap option, install the spacer, soap
dispenser and cover using the third tie rod (8-5/8"
long) and second coupling nut as shown. Secure
with acorn nut and set screw.
Secure actuator module cover and top cover
with sprayhead restraining bracket, acorn nut
and set screw.
Coupling
Nut
Standard Tie Rod
21-5/8"
Juvenile Tie Rod
18-1/8"
Coupling
Nut
G
10
FOR O UNIT: Install 1/2" nominal copper tubing
supply lines (pass them through holes in cover
down through support column) and connect to
stops using suitable fittings.
Spacer
Module
Cover
4-1/4" Tie Rod
Actuator Module
Assembly
(S65-134)
Tie Bar
Standard Support Tube
(S57-005)
TAS/Juvenile Support Tube
(S57-006)
Sprayhead
(S05-054)
1/23/2013Bradley • 215-1471 Rev. F; ECN 13-00-001
TDB3108, WF3208
Installation
4b
Air Metering Valve Assembly for B Drain and H Drain Units with
Tie Pipe Option
A
Install hemmed end (not sharp end) of
support tube with gasket onto bowl.
B
Connect 1/2" supply tubing to sprayhead
with 3/8" NPT to 1/2" tube connector and
place sprayhead onto support tube. Run the
tubing down through the support tube and
connect to valve tube connector.
C
Insert the 1-1/2" vent pipe (supplied by
installer) down through the support tube and
thread into vented trap.
Actuator
Module
Assembly
Cover
Sprayhead
Tie Bar
Supply Tube
Section View of
B/H Unit Assembly
Actuator Module
Assembly (S65-132)
Cover
(107-185 (B))
(107-048 (O))
Tie Bar Pre-Pack
(S45-056)
Sprayhead
(S05-054)
1/2" Supply
Tube
Support Tube
STD (S57-005)
TAS/JUV (S57-006)
Drain
(S45-273)
Support
Tube Gasket
(125-011)
Terreon Deep Bowl
(Part No. Varies with color
of bowl. Contact your local
Bradley Rep for assistance)
®
Vented Trap
(111-024)
Access Panel
(186-1191)
Pedestal Assembly
(S17-242)
Valve Assembly
(S08-373)
Bradley • 215-1471 Rev. F; ECN 13-00-001
B/H
(B shown)
1/23/2013
11
TDB3108, WF3208
4b
Installation
Air Metering Valve Assembly for B Drain and H Drain Units with
Tie Pipe Option continued...
D
Place the actuator module assembly on top of the
sprayhead. Drop 1/8" diameter tube down to the
valve assembly and connect to the air valve.
UNIT WITH “H” DRAIN AND ACTUATOR
MODULE SHOWN, ALSO AVAILABLE
WITH “B” DRAIN
Top
Cover
Skip to step F for units without soap.
E
Soap
Dispenser
For units with soap option, slide the spacer and
soap dispenser over the 1-1/2" pipe.
Spacer
F
Position the upper tie bar slightly below the module
or soap dispenser and fasten securely to vent pipe
with set screws provided. Secure top cover to tie
bar with two cap screws provided.
G
FOR B UNIT: Install 1/2" nominal copper supply
lines (pass through holes in cover and through
support column) and connect supply lines to stops
using suitable fittings.
Module
Cover
Tie Bar
Support Tube
Standard (S57-005)
TAS/Juv (S57-006)
12
Actuator
Module
Assembly
(S65-132)
Sprayhead
(S05-054B
1/23/2013Bradley • 215-1471 Rev. F; ECN 13-00-001
TDB3108, WF3208
Installation
5
Valve and tubing connections
Flush supply lines before making connections.
Connect 1/2" dia. tubing to tee and solenoid
assembly, two places. The male connector
for the valve assembly will remain tight and
leakproof when tubing is cut and installed
properly. Follow the procedures below when
installing tubing to ensure that you achieve a
leakproof seal.
A
• Using a sharp razor, cut tubing squarely
and remove any burrs. DO NOT pinch or
crush end of tubing.
• Loosen nut on fitting. Moisten end of tube
and push into fitting until it is firmly seated.
Tighten nut to secure tube to fitting (make
sure nut is securely tightened).
•
B
If connector leaks, reseat tubing
according to above procedure. If leaking
persists, replace male connector, or call
your Bradley representative for assistance.
C
D
E
Use wire tie to secure valving to valve bracket.
Connect the 1/2" NPT female end of the stop/
check valves to the rough-ins.
Attach flexible hosing to thermostatic mixing
valve, two places.
F
Insert the filter washers (provided) into the
swivel nut at the end of the supply hoses and
connect to the stop/check valves.
G
H
I
Check to make sure both Stop/Check valves
and volume control valve is fully open.
Turn on the main water supply and check for
leaking.
Push operating Pushbutton until air is purged
from lines.
Release
Button
Hang valve assembly on pedestal valve bracket.
Tubing
For “O” and “B” units (overhead supplies)
skip steps C through E.
Male
Connector
Valve Assembly
(S08-373)
1/2" Dia. Tube to
Sprayhead
3/8" NPT x
1/2" O.D. Tube
(269-639)
Check Valve
(269-1140)
3/8" Nipple
(113-006EC)
Reducer
(169-059)
1/8" Tee
(S53-046)
To Actuator
Connector
(2) Places
Tube
Connector
(169-890)
Air Valve Timer
Adapter
(198-008)
Air Valve
(S07-044)
Locking
Slope
Sealing
Ring
Gripping
Ridge
Tube
Stop
(1) 1/8" Tube
Connector Tee
Valve Bracket
(2) 1/8" Air Supply
From Actuator
Module
1/2" Tube
From
Sprayhead
Pedestal
Cold Supply
Flexible Hose
Wire Tie
Hot Supply
Flexible Hose
Volume Control
(S02-045)
Flexible
Hose
Filter
Washer
Thermostatic Mixing
Valve Assembly
(S67-597)
Volume
Control
Stop/
Check
Bradley • 215-1471 Rev. F; ECN 13-00-001
1/23/2013
13
TDB3108, WF3208
6
Installation
Adjust the Temperature
This valve is NOT factory preset. Upon installation, the temperature of this valve
must be checked and adjusted to ensure delivery of a safe water temperature. Water
in excess of 110°F (43°C) may cause scalding.
A
14
Check the temperature when
approximately 1.0 GPM water flow
is reached and adjust if necessary
(the range of the valve is 95°F–115°F
(35°C–43°C)). To adjust the temperature
follow steps B through F
B
Loosen temperature locking nut with
wrench.
C
Using a blade screwdriver, turn the
adjustment stem counterclockwise to
increase the temperature or clockwise to
decrease the temperature.
D
Once desired temperature is reached,
tighten nut to prevent temperature change.
E
Clean sprayhead if necessary. Adjust the
volume control to control the flow of water.
F
Attach pedestal access panel and kick
plate with hardware provided.
Temperature
Adjustment Stem
Temperature
Locking Nut
1/23/2013Bradley • 215-1471 Rev. F; ECN 13-00-001
TDB3108, WF3208
Installation
Cleaning and maintenance instructions for Terreon
®
Material Description: Terreon is an NAHB Certified densified solid surface material composed of polyester resin and is resistant
to chemicals, stains, burns and impact. Surface damage can be easily repaired with everyday cleansers or fine grit abrasives.
®
Routine Cleaning: Clean daily or as often as conditions require using a standard commercial or household cleaner such as
Formula 409 or Windex .
®
®
Stubborn Stains: Remove tough stains with Ajax , Comet , or Soft-Scrub and a green Scotch-Brite pad or lightly sand in a
circular motion with 240 grit wet/dry sandpaper. The finish can be renewed with a maroon Scotch-Brite pad.
®
®
®
®
Special Situations for Material
Scratches: Remove scratches with a green Scotch-Brite pad. The finish can then be renewed with a maroon Scotch-Brite pad.
®
®
Hard Water Deposits: Remove hard water deposits with a mild solution of vinegar and water. Always rinse the unit thoroughly
after cleaning.
Restoring the surface: Use Hope’s Solid Surface cleaner and polish to refresh and protect the Terreon Solid Surface material.
Bradley recommends additional care and maintenance for the darker colored Terreon. For complete instructions on this additional
maintenance see Bradley document #1505.
®
NOTICE! Do not use strong acid or alkaline chemicals and cleansers to clean Terreon. If these chemicals
come in contact with the Terreon surface, wipe them off immediately and rinse with soapy water.
Avoid contact with harsh chemicals such as paint remover, bleach, acetone, etc. Avoid contact with
hot pans and objects.
Repair Kits: Terreon repair kits are available. Contact your Bradley representative or distributor for part numbers and pricing.
Repair kits are made to order and have a shelf life of 30 days.
Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an endorsement, nor
does the omission of any brand name cleaner imply its inadequacy. Many products named are regional in distribution, and can be
found in local supermarkets, department and hardware stores, or through your cleaning service. It is emphasized that all products
should be used in strict accordance with package instructions.
Cleaning/Maintenance Instructions for Gel-coated Fiberglass
Material Description: The Terreon Washfountains referenced in this installation manual use a gel-coated fiberglass pedestal.
Routine Cleaning: The gel-coated pedestal should be cleaned daily or as often as needed with a mild solution of detergent and
water. Always use a soft cloth to avoid damage to the finish.
Repair Kits: There are no repair kits available for fiberglass materials. However, replacement parts are available, contact your
Bradley representative for pricing and part numbers.
NOTICE! Do not expose gel-coated fiberglass to solvents as they will damage the material and may create
harmful fumes.
Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an endorsement, nor
does the omission of any brand name cleaner imply its inadequacy. Many products named are regional in distribution, and can be
found in local supermarkets, department and hardware stores, or through your cleaning service. It is emphasized that all products
should be used in strict accordance with package instructions.
Bradley • 215-1471 Rev. F; ECN 13-00-001
1/23/2013
15
TDB3108, WF3208
Installation
Cleaning and maintenance instructions for stainless steel
Material Description: Stainless steel is extremely durable, and maintenance is simple and inexpensive. Proper care, particularly
under corrosive conditions, is essential. Always start with the simplest solution and work your way toward the more complicated.
Routine cleaning: Daily or as often as needed use a solution of warm water and soap, detergent, or ammonia. Apply the cleaning
solution per the manufacturer’s instructions and always use a soft cloth or sponge to avoid damaging the finish.
Stubborn Stains: To remove stains from stainless steel use a stainless steel cleaner and polish such as Ball stainless steel
cleaner or a soft abrasive. Always follow the manufacturer’s instructions and apply in the same direction as the polish lines.
®
NOTICE! Never use ordinary steel wool or steel brushes on stainless steel. Always use stainless steel wool
or stainless steel brushes.
Special Situations for Material
Fingerprints and Smears: To remove fingerprints or smears use a high quality stainless steel cleaner and polish in accordance
with the manufacturer’s instructions. Many of these products leave a protective coating that helps prevent future smears and
fingerprints.
Grease and Oil : To remove grease and oil use a quality commercial detergent or caustic cleaner. Apply in accordance to the
manufacturer’s instructions and in the direction of the polish lines.
Precautions: Avoid prolonged contact with chlorides (bleaches, salts), bromides (sanitizing agents), thiocyanates (pesticides,
photography chemicals, and some foods), and iodides on stainless steel equipment, especially if acid conditions exist.
NOTICE! Do not permit salty solutions to evaporate and dry on stainless steel.
The appearance of rust streaks on stainless steel leads to the belief that the stainless steel is rusting. Look for the actual source
of the rust in some iron or steel particles which may be touching, but not actually a part of the stainless steel structure.
NOTICE! Strongly acidic or caustic cleaners may attack the steel, causing a reddish film to appear. The use
of these cleaners should be avoided.
Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an endorsement, nor
does the omission of any brand name cleaner imply its inadequacy. Many products named are regional in distribution, and can be
found in local supermarkets, department and hardware stores, or through your cleaning service. It is emphasized that all products
should be used in strict accordance with package instructions.
16
1/23/2013Bradley • 215-1471 Rev. F; ECN 13-00-001
TDB3108, WF3208
Installation
Soap Valve — Liquid — S09-007S
Parts List
Attaching
Parts
S09-007S
Item
Part No.
Description
1
118-025
Valve Body
1
2
110-007
Packing Nut
1
3
135-001L
Spring
1
4
125-001BU
Washer
1
5
119-028
Plunger
1
*
161-014
Nut
1
*
124-001D
Washer
2
*
142-002AH
Washer - Stainless Steel
1
3
1
Qty
4
5
2
* Not Illustrated
This valve delivers a measured amount of soap with each upward stroke. The soap
dispenser has been standard on washfountains since 1983 and is not well-suited for
very thick lotion soaps.
NOTICE! Lotion soap will clog liquid soap valves. Use only lotion soap
valves with lotion soap.
Soap Valve — Lotion — S09-057S
Parts List
Valve
Assembly
S09-057
Item
Part No.
1
124-001D
2
110-057
3
125-001AN
4
159-114
5
124-001AT
6
160-176
7
8
Description
Attaching
Parts
S09-057S
Qty
6
2
4
Washer
—
1
Nut
—
1
Stopper
—
1
Reinforcing Plate
—
1
Washer
—
1
Screw
—
1
S09-040
Valve
1
1
S53-045
Adaptor
1
1
Bradley • 215-1471 Rev. F; ECN 13-00-001
5
1
3
7
1/23/2013
8
17
TDB3108, WF3208
Installation
Soap Valve — Powdered — S09-010A
Parts List
Item
Part No.
Qty
1
160-069
1
Screw, 1/4-20 RD
2
142-002X
1
Washer, 1/4 Split-Lock
3
S62-002
1
Agitator / Slide Assy.
4
192-004
1
Lever - Powdered Soap
1
2
Description
3
4
Reducer plugs are available for use with fine granulated
soap to reduce the flow.
Valves can be changed from powdered to liquid by plugging the innermost, or “bearing” hole with rubber plug,
part number 125-001AK. To change from liquid to powdered, the plug must be removed. If none is present, it
will be necessary to drill out the bearing hole with a 1/2" or 5/8" drill. The plastic container configuration forms
a natural template for locating the bearing hole.
Soap Maintenance Tips
Soap Recommendations
Quality soap dispensers require good quality soap and periodic maintenance to properly operate. Bradley soap dispensers will
provide dependable, consistent operation over the long term when soap with reasonable viscosity and pH levels are used and
when a minimal amount of periodic maintenance is performed on the valves.
Soap thickness is determined by a measurement called viscosity. Soap viscosity should be between 100 cps (centerpoise) and
2500 cps for all Bradley soap dispensers. Thinner soaps are perceived by the users as being “watered down” so users tend to
take more than they need, resulting in waste. Thick soaps flow slower and inhibit the “flushing” action of the valves, which
allows the soap to congeal in the valve and cause clogs.
The pH (acid) level of the soap should be in the range of 6.5 to 8.5. More acidic soaps (pH levels lower than 6.5) will corrode
metal parts (even stainless steel!!) and degrade rubber and plastic components. They will also cause skin irritation. Most
inexpensive soaps (typically the pink lotion type) fall into this acidic category and will eventually cause valve failure and
metal corrosion. Base soaps (pH levels higher than 8.5) will cause swelling or degradation of rubber and plastic parts and skin
irritation.
Generally, any quality soap meeting the viscosity and pH guidelines above will work well with Bradley soap dispensers. PCMX
or Isapropanol based antibacterial soaps (within viscosity and pH limits) will also work with Bradley dispensers. Soaps satisfying
these basic guidelines will provide consistent flow and reduce clogs.
Most soap dispenser problems are caused by soap that is too thick or corrosive, or by a lack of maintenance. Many soaps come
in concentrate form which must be diluted with water. Often, the soap is improperly diluted or used straight out of the bottle, which
causes clogging and valve failure. If proper soap is being used, valves that have never been cleaned are usually the source of
dispensing problems. Bradley has entered into an agreement with Champion Brand Products to provide additional customer
service for purchasers of our dispensers regarding soap issues. They are very helpful and can get to the bottom of almost any
soap dispenser related problem. They also sell an excellent “Bradley approved” soap. Please see Soap Instruction Sheet 215-1286
for details about soap valve cleaning or how to contact Champion. With proper maintenance and soap, Bradley dispensers will
provide long term, trouble free operation.
Soap Dispenser Maintenance Instructions
Bradley soap dispensers will provide dependable, consistent operation over the long term when the proper soap is used and when
a minimal amount of periodic maintenance is performed on the valves. Valves must be maintained (cleaned) to function properly.
To ensure proper operation of your soap dispenser, follow these instructions:
• Once per month, unscrew valve from reservoir and soak it for 30 minutes in hot water.
• Push valve at least 20 times while it is soaking.
• Flush soap reservoir with hot water while valve is soaking.
In cases of extreme clogging, the valve should be disassembled and the parts should be soaked in hot water or cleaning solution
to restore proper functioning. Soap dispensers that will not be used for extended periods of time (schools during summer break,
etc.) should be drained, cleaned and left empty until put back into service. Soap left on the outside of dispensers can cause
discoloration and corrosion of the reservoir (even on stainless steel units). All soap should be wiped or scrubbed off daily, then the
outside of the dispenser should be rinsed with clear water and dried with a soft cloth.
18
1/23/2013Bradley • 215-1471 Rev. F; ECN 13-00-001
TDB3108, WF3208
Installation
Sprayheads — Standard w/Neoprene Spray Ring Grommet
Repair kit does not include sprayhead
grommet. Order as a separate item.
1
4
3
2
5
9
7
10
6
8
Parts List
Sprayhead
Assembly
S05-054B
Item
Part No.
1
125-001DE
Description
Repair
Kit
S45-051
Qty
Neoprene Washer - Top
1
1
Sprayhead Manifold
1
—
Washer
3
4
2
139-031
3
124-001AL
4
160-211
Carriage Bolt
3
4
5
115-061
Sprayhead - Top
1
—
6
116-008
Sprayhead - Bottom
1
—
7
124-001AT
Washer
3
4
8
161-025
Nut
3
4
9
124-020C
Sprayhead Grommet - Circle
1
—
10
125-001DF
Neoprene Washer - Bottom
1
1
Sprayhead Troubleshooting
Problem
Water splashes over the
rim of the bowl.
Possible Cause
Solution
Foreign matter has reduced
Clean the sprayhead:
the size of the sprayhead slots,
1. Disassemble the sprayhead and dislodge any dirt, lime buildcausing greater pressure at the
up and foreign debris with a wire brush.
open slots.
2. Sprayheads with rubber grommet spray rings may be cleaned
by rubbing a coin over the grommet.
3. Throttle down the volume control (water spray should strike
the bowl without splashing outside of the bowl).
Water flow diminishes
from the sprayhead.
Strainer portion of the stopRemove and clean the strainer screen from the stop-strainer-check
strainer-check valve is plugged. valve.
The sprayhead shown above includes a perforated neoprene spray ring grommet that is self-cleaning. The
water pressure flexes the spray holes which slows accumulation of foreign matter and tends to “break loose”
any such deposits that may have accumulated.
Bradley • 215-1471 Rev. F; ECN 13-00-001
1/23/2013
19
TDB3108, WF3208
Installation
Actuator Module Components
U-Cup* (125-099)
Piston* (119-227A)
Duckbill Check* (198-010)
Spring* (135-065)
Screw (160-165)
Actuator Body* (118-279)
Pushbutton Assembly (S08-324)
Straight Tube Connector* (169-890)
Nut (110-115)
Acutator Bracket (140-743)
* Included in Actuator Assembly (S65-168)
Metering Air Valve Maintenance
Adjust Air Valve Meter Time
The air valve timer is located next to the tube connector on the air valve body. The timer is capped with
a filter to prevent build-up on the timer. The air valve timing can be adjusted from 5 to 60 seconds.
A
Remove filter cap and use a screwdriver to
tighten or loosen the timer. Turning the timer
clockwise increases the time; turning the
timer counterclockwise decreases the time.
B
Continue to adjust until the timer is set at
desired length.
C
Replace filter cap over the timer.
Tube Connection Leaks
A
Push in the white manual release button
while pulling the tube out to disconnect the
tube at the connector. No tools are needed.
B
To correct a leak, press tubing firmly into the
connector and make sure it is seated.
C
If leak persists, remove tubing from the fitting
and trim the tubing end square with a razorsharp knife. If leak continutes, replace the
fitting or contact your Bradley representative
for assistance.
Air Valve Tubing
Manual Release
Button
Locking Slope
Sealing Ring
Gripping Ridge
Tube Stop
20
1/23/2013Bradley • 215-1471 Rev. F; ECN 13-00-001
TDB3108, WF3208
Installation
Repair Kits and Troubleshooting – Metering Air Valve
Turn off water supplies to the unit before
troubleshooting.
Lower Valve
Body (118-183)
Rubber Diaphragm
(269-665)
Plastic Disk
(269-664)
Stainless Steel
Disk (179-082)
Spring
(135-053)
1/4" Tube
Connector
Valve Seat
(117-036)
Center
Hole
Parts Included in
Kit (S65-110)
Repair Kit (S73-054A)
(This repair kit also
includes S65-110)
Metering
Air Valve
Lockwasher
(142-002CR)
Screw
(160-313)
Problem
Valve will not shut
OFF.
Cause
Timing
mechanism is
clogged.
Solution
Clean and inspect timing mechanism:
1. If compressed air is available, blow water and debris from timer cover of timing
mechanism.
2. Turn adjusting screw out all the way. Clean and inspect screw and valve body.
3. Turn adjusting screw in to desired cycle time.
Valve will not turn
ON.
Water is not being Open all stops on mixing valve.
supplied to unit.
Timing can not be
adjusted for more
than 5 seconds.
There is an air
leak.
Pushbutton does not
work properly.
Air volume may
Check for leaks and lubricate U-cup:
not be sufficient to
1. Check all fittings for air leaks.
operate valve.
2. Disassemble pushbutton and lubricate U-cup seal (see pushbutton assembly
diagram).
Valve cycles
properly, but water
does not form
streams and drips
from
the streamformer
Debris has
accumulated
in flow control
assembly.
Check the valve assembly:
1. Check all tubing and fittings for proper assembly.
2. Tighten all screws which hold valve together..
Clean and inspect flow control assembly:
1. Remove tubing and tube connector fittings from metering air valve.
2. Inspect flow control and remove debris that may be clogging the assembly.
3. Replace fittings using teflon tape or pipe sealant. Do not get sealant on the flow
control.
4. Replace tubing by cutting 1/4" from end of tube.
• Make sure end is square, then insert into tube connector fitting.
Water is dripping
from the
streamformers.
Debris has
accumulated
on valve seat or
orifices.
Clean and inspect valve seat:
1. Remove screws and disassemble metering valve.
2. Clean valve seat and inspect for deep gouges or scratches. Replace if necessary.
3. Remove all debris that may be clogging center hole of plastic diaphragm assembly.
4. Remove any debris clogging off-center hole in rubber diaphragm.
Bradley • 215-1471 Rev. F; ECN 13-00-001
1/23/2013
21
TDB3108, WF3208
Installation
Manual Mixing Valve Repair Parts
Valve
Assembly
S01-038
Item
Valve
Assembly
S01-038S
Valve
Assembly
S01-038A
Valve
Assembly
S01-038AS
Repair Kit
S45-197
Part No.
Description
Qty.
1
118-034
Mixing Valve Body - Brass
1
1
—
—
—
1
118-034A
Mixing Valve Body - Chrome
—
—
1
1
—
2
124-001BD
Fiber Washer
1
1
1
1
1
3
125-001BC
O-Ring
1
1
1
1
1
4
119-059
Mixing Valve Core
1
1
1
1
1
5
152-038
Roll Pin
1
1
1
1
1
6
121-016
Bonnet - Brass
1
1
—
—
1
6
121-016A
Bonnet - Chrome
—
—
1
1
—
7
160-197
Screw - Brass
1
1
—
—
—
7
160-189
Screw - Stainless Steel
—
—
1
1
—
*
129-007
Tailpiece - Brass
—
2
—
—
—
*
110-005
Tailpiece Nut - Brass
—
2
—
—
—
*
129-007A
Tailpiece - Chrome
—
—
—
2
—
*
110-005A
Tailpiece Nut - Chrome
—
—
—
2
—
*
124-001AF
Tailpiece Washer
—
2
—
2
2
*Parts not shown
Volume Control Valve Repair Parts
Brass Valve
S02-045
Repair Kit
S45-198
Item
Part No.
1
125-001BC
O-Ring
1
1
1
2
152-038
Roll Pin
1
1
1
3
121-016
Bonnet
1
—
1
3
121-016A
Bonnet
—
1
—
4
124-001BD
Fiber Washer
1
1
1
5
119-060
Valve Core
1
1
1
6
118-033
Valve Body
1
—
—
6
118-033B
Valve Body
—
1
—
22
Description
Chrome
Valve
S02-045A
Qty.
1/23/2013Bradley • 215-1471 Rev. F; ECN 13-00-001
TDB3108, WF3208
Installation
Vernatherm Thermostatic Mixing Valve (S01-525) Parts List
Parts List – S65-259 Valve Repair Kit
Item
Part No.
Qty.
Description
5
S39-413
1
Thermostat
7
125-001BX
1
O-Ring
8
125-157
1
O-Ring
10
1
Bradley • 215-1471 Rev. F; ECN 13-00-001
Nut 3/8-24 Hex Jam
9
Cap
8
O-Ring
7
O-Ring
6
Stem
5
Thermostat
4
Piston
3
Spring
2
Seal Cup
Valve Body
1/23/2013
23
TDB3108, WF3208
Installation
Thermostatic Mixing Valve Troubleshooting
Before attempting to troubleshoot the valve or disassemble the components, check for the following
conditions:
• If stop/check valves are used, make sure that they are fully open.
• Make sure that the hot and cold inlet pipes are connected properly, and that there are no cross-connections
or leaking stop/check valves.
• Check the hot water heater output to make sure that it is at least 20° F above the set temperature.
Be sure to close the appropriate shut-off valves prior to disassembly of the valve and reopen the valves after inspection
and repair is complete.
Problem
Cause
Solution
External leaks.
Damaged O-rings.
Replace O-rings where necessary. For replacement of the
O-rings, contact your Bradley representative and ask for
Repair Kit (part number S65-259).
Improper water
temperature or
temperature
fluctuation.
Thermostat is slowly failing or not working at all.
Check the thermostat for proper operation.
1. At room temperature (80° F or less) remove cap
and thermostat.
2. Place thermostat into container with 115° F water.
The pushrod should pop out of the thermostat
approximately 1/10".
3. If thermostat pushrod does not pop out, the
thermostat must be replaced. Contact your Bradley
representative and ask for Repair Kit (part number
S65-259).
Valve temperature is not properly set.
Limited water flow. Dirt and debris have built up in the valve or strainer.
Adjust the temperature as shown on page 14, step 6.
Remove and clean strainer. If strainer needs to be
replaced, order Bradley part no. 173-028.
Check the piston for smooth movement.
1. Remove the valve's cap and thermostat.
2. Push down on the piston with your finger (the piston
should move freely). If the movement is not as it
should be, the piston needs to be cleaned. Follow
the method outlined below for cleaning the piston
and valve body:
• Remove the thermostat.
• Lift the piston out with a needle-nose pliers
and remove the spring.
• Any cleaner suitable for brass and stainless
steel may be used (if cleaning with suitable
cleaner is not sufficient to remove debris, a
400-grit sandpaper may be used to polish and
hone the piston and valve body).
• Snap spring into piston (will detent) and
reassemble into the valve body. Retest the
piston.
3. If, after a thorough cleaning, the piston does not
move freely, the piston must be replaced. Contact
your Bradley representative and ask for Repair Kit
(part number S65-259).
24
1/23/2013Bradley • 215-1471 Rev. F; ECN 13-00-001
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising