GEM-P800 Rev D Installation Manual
®
GEM-P800
Control Panel / Communicator
Installation Instructions
© NAPCO 2009
WI850D 6/09
WI850D GEM-P800 Installation Instructions
Table of Contents
General Information
GEM-P800 Features
General Information .......................................... 2
GEM-P800 Features ......................................... 2
Specifications .................................................... 3
UL Compatible Smoke Detectors ...................... 4
Listings and Approvals ...................................... 4
Ordering Information ......................................... 4
Optional Accessories......................................... 4
Programming the Panel..................................... 5
Installation ......................................................... 6
Wiring ................................................................ 6
Keypad Operation ............................................. 7
Panel Operation ................................................ 8
Bypassing ......................................................... 9
User Program Mode .......................................... 9
GEM-P800 Commands ..................................... 10
Dealer Commands ........................................... 11
Wireless Operation (Signal Strength) .............. 11
Zone Features ................................................... 12
System Times ................................................... 13
System Features ............................................... 14
Telephone Number 1 Programming .................. 15
Backup Telephone Programming ...................... 17
Pager Programming .......................................... 17
Telephone Number 3 Programming .................. 18
Report Codes .................................................... 18
Enhanced Communicator Features ................... 19
Wireless ............................................................ 19
Downloading ..................................................... 21
Dealer Programming ......................................... 22
System Troubles ............................................... 23
Troubleshooting ................................................ 25
GEM-P800 WIRING DIAGRAM......................... 27
The GEMINI GEM-P800 control panel provides up to
6 hardwired/wireless zones, a 2-wire fire zone and 2
wireless only zones. Up to eight 4-digit user codes
can be programmed. Ambush, when selected, uses
User 8 code as an Ambush code.
Control Panel
• 8 Zones (6 Hardwired/Wireless + 2 wireless)
• 2-wire Fire Zone
• 3 Keypad Panics
• Wireless Ready
• Bell Supervision
• Line Cut Detection
• Answering Machine Override (Second Call)
• 50 Event Log
The GEM-P800 is wireless ready. When used with a
GEM-RECV-XP8 receiver, the control panel can support up to 8 wireless zones, 4 wireless smoke detectors and 4 Keyfobs.
The GEM-RP8 keypad provides complete control of
the GEM-P800 control panel. Information on system
status, bypassed zones, system troubles etc. can be
viewed at the keypad.
The control panel can be easily and quickly programmed from the keypad. The panel can also be
locally or remotely downloaded using PCD3000 software and a PCI 2000/3000 interface or PCL2000A
local Download cable. See Downloading Section
(page 5) for more information.
Communicator
• 2 Telephone Numbers
• Backup Reporting
• Pager Format
• Point ID Format
• Individually Report 8 Users
• Opening after Alarm Report (Cancel Code)
• Conditional Closing Report
NAPCO Security Systems, Inc.
333 Bayview Avenue
Amityville, New York 11701
For Sales and Repairs, call Toll Free: (800) 645-9445
For Technical Assistance, Contact the NAPCO Toll Free Helpline
(800) 645-9440
2
Specifications
Current & Voltage Ratings
Alarm Output ------------------------------------ Burg: 12VDC, 2A (max.)
Fire:------------------------------------------------- 12VDC, 95mA
Output Current Limiting------------------------ Burg/Fire: 2.25A
AUX Power: -------------------------------------- 750mA
Residential Burglary (4 Hour Standby)
Combined Standby Current: ----------------- 500mA
Bell Output: -------------------------------------- 2A
(Using Rechargeable 12 VDC 4 AH BATTERY, minimal requirement)
Residential Fire (24 Hour Standby)
Combined Standby Current: ----------------- 175mA
Bell Output: -------------------------------------- 95mA
(Using Rechargeable 12 VDC 7 AH BATTERY, minimal requirement)
UL Ratings
Residential Burglary (4 Hour Standby):
Combined Standby Current ------------------ 500mA
Bell Output ---------------------------------------- 200mA
(Min. 4AH Battery)
Residential Fire (24 Hour Standby):
Combined Standby Current ------------------ 175mA
Bell Output ---------------------------------------- 95mA
(Min. 7AH Battery)
Transformer and Battery
Required Transformer: ------------------------NAPCO TRF12
Required Battery: -------------------------------12V 4AH or 7AH Rechargeable
(Change Battery every 5 years or as required)
Maximum Charging Current: -----------------165mA
Maximum Input Current: -----------------------2.58A
Loop Characteristics
Loop Voltage: ------------------------------------5 Volts
Loop Current : ------------------------------------Zones 1, 2, 3: 0.9mA (2.2 K)
Zones 4, 5, 6: 0.5mA (3.9 K)
Loop Resistance: --------------------------------100Ω per zone (max.)
2 Wire Fire Loop Resistance -----------------10Ω (max.)
Device Specifications
Max # keypads: ----------------------------------4, GEM-RP8 current = 65mA
Max # of receivers: ------------------------------2, GEM-RECV-XP8
current = 65mA each
Max # of compatible
2-wire smoke detectors: -------------------10
Max Keypad wire length: ----------------------1000’ total wire length
Miscellaneous
Housing Dimensions: ----------------------11" x 121/8" x 3"
(28cm x 30.8cm x 7.6cm) HxWxD
Shipping Weight: ---------------------------GEM-P800 5.5lbs.
Operating Temperature: --------------------0-49ºC (32-120°F)
3
WI850D GEM-P800 Installation Instructions
UL Compatible Smoke Detectors
GEM-P800 Compatible Smoke Detectors
Mfg
Sentrol
System
Sensor
2-Wire
Smoke Detector
712U
722U
732U
711U
721U
2WTA-B
721UT
731U
2100
2100T
1100
GEM-P800
GEM-RP8
ZDR
OI219
WI851
8 zone Control Panel with 2-wire Fire (6 Hardwire/
Wireless+2 wireless Burgs, 4 wireless Fire 4 keyfobs)
Keypad
Zone Doubling Resistors (2.2K & 3.9K)
Operating Instructions GEM-P800
Programming Instructions GEM-P800
Optional Accessories
Compatibility Identifier: GEM-P800
Listings and Approvals
UL HOUSEHOLD FIRE AND BURGLARY WARNING SYSTEM CONTROL UNIT
STANDARDS # 1023, 985. ULC HOUSEHOLD FIRE AND BURGLARY
STANDARDS C1023, S545. IN CANADA THE KNOCKOUTS IN THE ENCLOSURE SHALL NOT BE USED WITH CONDUIT IN RESIDENTIAL FIRE
INSTALLATIONS.
VERIFIED TO COMPLY WITH F.C.C. PART 15 AS CLASS B : DIGITAL DEVICE.
Warning: The use of non-NAPCO wireless devices with this
control panel has not been evaluated by UL and voids the UL
listing. In addition, the performance of these devices can not
be guaranteed as compatible with NAPCO control panels.
4
Ordering Information
GEM-RECV-XP8
GEM-TRANS2
GEM-RTRANS
GEM-KEYF
GEM-HEAT
GEM-WP
GEM-SMK
GEM-PIR
GEM-DT
GEM-GB
RB1000
Veriphone
PCD3000
PCI2000/3000PC
L2000A
*Wireless Receiver
Window/Door Transmitter
Window/Door Recessed Transmitter
Keyfob Transmitter
Wireless Heat Detector with Rate of Rise
Wireless Panic Transmitter
Wireless Smoke Detector (GEM-SMK-1, GEM-SMK-1R)
Wireless PIR (GEM-PIRPET)
Wireless Dual-Technology Sensor
Wireless Glass-Break Detector‡
Relay Board
Audio Verification Module‡
Downloading Software for IBM PC Compatibles
Software with Interface for IBM PC Compatibles
(Includes PCL2000A Local Download cable)
*Supports up to 8 zones, 4 Key Fobs, 4 Smoke Detectors (total
16 devices).
‡
Not Evaluated by UL.
Note: Access Features have not been evaluated by UL.
Programming the Panel
Refer to GEM-P800 Programming Instructions (WI851)
Defaulting the Panel
1. Remove power from the panel.
2. Remove all wiring from terminal 15 (PGM)
and terminal 3.
3. Connect terminal 15 (PGM) to terminal 3.
4. Apply power to the GEM-P800 control panel.
5. After a few seconds the ARMED, READY
and H SYSTEM TROUBLE LED's will flash.
6. The keypad will beep 3 times indicating the
panel default values have been loaded.
7. Remove wiring between terminal 15 (PGM)
and terminal 3.
8. Re-install original wiring for terminal 15
(PGM) and terminal 3.
NOTE:
The panel can also be automatically
downloaded/uploaded using PCD2000 Software
running
PCPreset. For Site Initiated Downloaded, see
Auto Download ID Number [93].
Local Downloading
Wire as shown in Figure 1. Use the power up or
A6 method of establishing a connection.
The power up method is recommended if the panel is
attempting to report.
-13
14
15
16
17
18
19
GND
GREEN
PGM
(-)
TIP
RING
TIP
RING
TELCO
PHONE
GRY
RED
GREEN
+12
+PWR
-13
14
15
16
17
18
19
GND
GREEN
PGM
(-)
TIP
RING
TIP
RING
TELCO
PHONE
BRN
RJ31X
GEM-P800 Panel at the site
RED
RED
BLACK
GREEN
TELCO
PCI2000
PCL2000A
MODEM
Keypad Programming
J1
J2
TO COMPUTER
TO EXTERNAL
MODEM
J3
LOCAL
TO
J4
TELCO
J5 LINE
OUT TO
FIGURE 1 LOCAL DOWNLOAD
MODEM
Downloading
The GEM-P800 panel can be download/
uploaded with PCD3000 software using the Ring
Method, Answering Machine Override (Second
Call) or A6 Method of downloading.
+12
+PWR
Any programming in Dealer Options 1 [96] and Dealer
Options 2 [97] will not be defaulted. If Dealer Code Lockout has been programmed the panel will not default the
Dealer Code.
Refer to WI851 for information on keypad programming.
the following methods:
1. The A6 method
2. Call-in method
3. Answering Machine Override (Second
Call)
4. Site-Initiated (PCPreset & A6)
5. Automatic Downloading (Using PCPreset)
Remote Downloading
Wire as shown in Figure 2. The panel can be
remotely download/uploaded using any one of
FIGURE 2 REMOTE DOWNLOAD
5
WI850D GEM-P800 Installation Instructions
Installation
Mounting the Panel
Mount the Panel close to an unswitched AC
source, a cold-water pipe ground, and a telephone line connection.
Mounting the Keypad
A keypad should be located near an exit/entry
door. To remove the keypad from the backplate,
insert a small screwdriver into the slots at the
bottom of the keypad. Pull up on the screwdriver to pop off the cover.
For increased protection, additional detectors
should be installed in areas other than those
required, such as the dining room, bedrooms
and utility room. Heat detectors, rather than
smoke detectors, are recommended in kitchens,
attics, and garages due to conditions that may
result in false alarms and improper operation.
Refer to NFPA Standard 74 (National Fire Protection Association, Batterymarch Park, Quincy,
MA 02269) for additional information, including
proper mounting methods.
Wiring
Terminal Block Wire Range: 14-22 AWG.
Grounding the Panel
Connect the control-panel EARTH GROUND
screw through a No. 16 AWG or larger wire to a
metal cold-water pipe, a UL Listed ground rod,
or an AC ground connector. Do not use a gas
pipe or a plastic pipe. Use at least #16 AWG
wire. Connect a wire with a ground lug crimped
or soldered onto one end and connect it to the
EARTH GROUND screw in the cabinet.
AC Power and Battery Wiring
Up to 4 keypads can be connected on individual
wire runs with #22 AWG wire with a maximum
total cable length of 1000 feet. Each keypad
draws approximately 65 mA.
Complete all wiring before connecting the battery or AC Power. Do not plug the transformer
into a switched outlet.
Telephone Wiring
Keypad Wire Color
Wire as shown in the wiring diagram in the back
of this manual.
Control Panel Terminal
RED
12 (+PWR)
BLACK
13 (GND)
GREEN
14 (GREEN)
WARNING
The FCC restricts the use of this equipment on
certain telephone lines. Read the FCC statement on the back of this manual to ensure compliance.
TABLE 1 KEYPAD W IRING
Typical Fire Installation
(Where permitted by local codes)
Install smoke detectors outside each sleeping
area and on each floor, including the basement.
Install the living room and basement smoke detectors near the stairway of the next upper level.
6
FIGURE 3 Typical Fire Installation
Burglary Zone Wiring
Fire Zone Wiring
NAPCO's EZ Zone DoublingTM is simple. Each
terminal has 2 zones, use an E (2.2 K) type
Zone Doubling Resistor for the primary zone
and a Z (3.9 K) type Zone Doubling Resistor for
the secondary zone.
Terminals
2.2 K Primary
3.9 K Secondary
3&4
Zone 1
Zone 4
5&4
Zone 2
Zone 5
6&7
Zone 3
Zone 6
Wire the Fire Zone as shown in the Wiring Diagram in the back of this manual. An EOL resistor must be installed, even if the Fire Zone is not
used. In UL installations, use a UL Listed
NAPCO EOL 2.2K resistor.
Fire Zone Normal
13.0V
Fire Trouble
13.8V
Fire
0.0 V
TABLE 4 VOLTAGE AT FIRE ZONE (Terminals 8 & 9)
TABLE 2 EZ ZONE DOUBLING™
PGM Wiring
Wire zones as shown in the wiring diagram (pg.
27). All resistors must be installed, even if the
zone is not used. If required, unsupervised
open circuit devices may be used instead of
closed circuit devices. Program the zone as an
Open Circuit Zone [06] (Zone Doubling Resistor
required). If necessary, use the voltage chart
below to verify proper voltages.
Primary (2.2K) and Secondary (3.9K) zones normal
1.9 V
Secondary (3.9K) open
2.5 V
Primary (2.2K) open
3.2 V
Primary (2.2K) and Secondary (3.9K) open
5.0 V
Primary (2.2K) and/or Secondary (3.9K) shorted (Sys. Trbl 7-Zone Trbl) 0.0 V
The PGM is a switched negative output that is
activated depending on the programming option
(s) that have been selected [08], [23] - [25].
Connect the device controlled by the PGM between +PWR and the PGM terminal (maximum
load of 50 mA).
Keypad Operation
Keypad zone LED's indicate zone status.
ARMED, STATUS and H SYSTEM LED's provide system status. The keypad sounder provides feedback beeps for correct and incorrect
entries.
Keypad Sounder
3 QUICK BEEPS
Panel Armed (System ON)
Chime ON
Fault Find Mode ON
Keypad Sounder ON
Zone Bypassed
6 QUICK BEEPS
Panel Disarmed (System OFF)
Chime OFF
Fault Find Mode OFF
Keypad Sounder OFF
Zone Un-Bypassed
1 SECOND - STEADY TONE
Incorrect Code Entered
Invalid key entry
4 LONG BEEPS (PRIORITY CONDITION)
1. Entering an Arm Code with a faulted zone
(Not an Auto-Bypass Reentry Zone).
2. Entering an Arm Code when the Bell or
PGM is ON (Bell and PGM will turn OFF).
3. Arming with the Fire LED ON - reset required. Press the C key.
TABLE 3 VOLTAGE AT TERMINALS 3&4, 5&4, 6&7
7
WI850D GEM-P800 Installation Instructions
Keypad LED's
Panel Operation
ARMED LED DEFINITION
Armed ............................................................ON
Instant Mode .................................... Rapid Flash
Zone in Alarm ........................................Flashing
Arming (System ON)
STATUS LED DEFINITION
Ready to be Armed ........................................ON
Zone faulted ................................................. OFF
H
TROUBLE LED DEFINITION
AC Failure ..............................................Flashing
System Trouble(s) ........................................ON
FIRE LED DEFINITION
code, followed by the
D
key, the keypad will
provide a feedback beep for each key pressed.
If a valid Arm/Disarm code is entered, the keypad will beep 3 times. If an incorrect Arm/
Disarm code is entered, the keypad will sound a
1-second tone indicating an incorrect entry.
Arming without Entry Delay (Instant
Mode)
Fire Alarm ..............................................Flashing
Fire Memory / *Fire Trbl .................................ON
*See Note 1
Enter the F key to eliminate the entry delay.
The ARMED LED will flash rapidly to indicate
the panel is in Instant Mode. If an Exit/Entry
Zone is tripped while the panel is in Instant
Mode the panel will go into alarm immediately.
AC LED DEFINITION
AC Present ....................................................ON
AC Failure ................................................... OFF
Arming/Disarming with a Keyfob
I
ZONE LED DEFINITION
Faulted Zone..................................................ON
Bypassed Zone .................................Slow Flash
Zone in Alarm ........................................Flashing
NOTE:
* If Fire Trouble on Fire LED [96-4] has been enabled, a steady
Fire LED will indicate Fire Trouble.
8
Before arming the system close all protected
zones (unless programmed as Auto-Bypass
Reentry Zones). Enter a 4-digit Arm/Disarm
The system can be armed by pressing the K
key, and disarmed by pressing the L key on
the Keyfob. Zones programmed as Exit/Entry
Follower Zones can be bypassed when the M
or N keys on the Keyfob have been programmed for Interior [81-84].
Zones programmed as Home/Away with Delay Zones can
be armed regardless of the state of the Exit/
Entry Zones when the M or N keys on the
Keyfob have been programmed for Full Set [8184]. To arm the system with all zones protected
press the K key. Press and hold the M or
N key for 1.5s to fully set the system (the LED
on the Keyfob indicate the Keyfob has transmitted the signal). Program Keyfob/Keyswitch Chirp
[23-4] for an audible indication of system arming
and disarming.
Arming/Disarming with a Keyswitch
The system can be armed/disarmed by using a
momentary Keyswitch wired to Zone 6. Program Keyfob/Keyswitch Chirp [23-4] for an audible indication of system arming and disarming.
NOTE:
Faulted Keyswitch or silent 24 hour zone normally do not
display at the keypad. If a silent 24 hour zone or Keyswitch
is faulted at the time of arming the faulted zone will display
only while the priority sound is ON.
Arming Instant with a Keyfob
The panel can be ARMED INSTANT when the
M or N keys on the Keyfob have been programmed for Instant [81-84]. To arm the system with Instant protection press the K key,
then press and hold the M or N key for 1.5s
to arm the panel with INSTANT protection.
Disarming (System OFF)
After entering the premises through an Exit/
Entry Zone, the keypad will sound the Entry Delay Tone. Enter a valid Arm/Disarm code, then
press D. If a valid Arm/Disarm code is entered,
the keypad will beep 6 times, indicating the
panel has been disarmed. The red Armed LED
will go out. If an incorrect Arm/Disarm Code is
entered, the keypad will sound a 1-second tone,
indicating incorrect entry. Press the C key
and re-enter the code.
Disarming after an Alarm (Alarm Memory)
The armed LED and the zone(s) that caused the
alarm will be flashing. Disarm the panel. The
system is currently not detecting zone faults or
displaying system trouble. The zone(s) that
caused the alarm will continue to flash. The
STATUS and H SYSTEM TRBL LED's are out
indicating:
• The system is displaying Alarm Memory.
Press the C key to clear Alarm Memory.
Bypassing
Automatic Bypassing
Home/Away with Delay Zones
This zone type has the following operation depending on whether an Exit/Entry Zone has
been violated during the Exit Delay time.
Home
Exit/Entry Zone is not violated
Zones selected as Home/Away with Delay
Zones will be bypassed automatically.
Away with Delay
Exit/Entry Zone is violated
Zones selected as Home/Away with Delay
Zones will have a fixed 20-second entry
delay when violated before an Exit/Entry
Zone.
Full Setting the System with Automatic
Bypassing - Home/Away with Delay
Zones
From the Keypad
Press BC to return protection to
Home/Away with Delay Zones that have
been automatically bypassed. Three minutes are allowed to walk through Exit/Entry
and Exit/Entry Follower Zones.
Using A Keyfob (GEM-KF)
All zones in the system can be armed regardless of the state of the Exit/Entry Zone
when arming with a Keyfob and using an
AUX key programmed as Full Set. Press
K and press and hold the M or N
keys for 1.5s when leaving the premises. All
zones, including Home/Away Zones are
armed..
Bypassing a zone
Press the B key, then the zone number to
be bypassed. While the panel is DISARMED,
the bypassed zone LED will flash slowly; indicating the zone has been bypassed. While the
panel is ARMED, the bypassed zones will only
be displayed if the Display Bypassed [21-3] option has been selected.
Unbypassing a zone (Disarmed only)
Press the B key then the number of the
zone to be unbypassed.
Group Bypass
Press the E key to Bypass all Exit/Entry
Follower Zones [02] or Home/Away Zones
[01] (only if the system is programmed exclusively for Home/Away with Delay
zones).
.
Using A Keyfob (GEM-KF)
Hold the M or N key on the Keyfob to
Bypass all Exit/Entry Follower Zones [02] or
Home/Away Zones [01] (only if the system is
programmed exclusively for Home/Away
with Delay zones).
User Program Mode
To prevent the loss of the User 1 Code, the
panel default program includes User 1 Code
Lockout [96-2].
To change the User 1 Code from its default
9
WI850D GEM-P800 Installation Instructions
value of 1234, program the 4-digit User 1 Code
through Dealer Programming [95]. User 1 Arm/
Disarm code is also used to program User
Codes 2 - 8. By default, the User 1 code cannot
be re-programmed by the user.
While in User Program Mode, Zones 1 through 8
will light to indicate any User Codes presently
programmed. Follow the example below to program User 2's code to 1923.
If it is necessary to change the User 1 code, it
can be changed through downloading or Dealer
keypad programming. From Dealer Program
Mode, change the User 1 Code Lockout ([96-2]
LED=OFF) to disabled.
User Mode Programming Example:
Your User 1 Code can be used to enter the User
Program Mode, where you can program other
User Codes. The following explains how you
will use this Code to program or erase additional
User Codes.
Entering User Program Mode
1. Enter A 8
2. Enter User 1 Code (1234)
(Default)
3. Press D
ARMED, STATUS AND
H
SYSTEM TROU-
BLE LED’s WILL FLASH CONTINUOUSLY.
KEYPAD WILL BEEP 4 TIMES.
GEMINI
H
ED
ARM
Zone LED
OFF
10
1
TUS
STA
A 1 is displayed indicating
User 1 Code is programmed
and 2-8 are blank.
Meaning
User Arm/Disarm Code not programmed
Flashing
User Arm/Code is currently being programmed
Steady
User Arm/Disarm Code has been programmed
TABLE 5
ZONE LED DEFINITION-USER PROGRAM MODE
1.Press 2, keypad will beep twice and
Zone 2 LED will Flash.
2.Enter 1923, Zone 2 LED
will continue to flash until the 4th digit is
entered. The keypad will beep 4 times confirming a valid entry (Zone LED steady).
Deleting a User Code
Press the User number to be deleted, the keypad will beep twice and the zone LED will be
flashing indicating the user has been selected.
Press F, and the LED associated with the
user will now be OFF.
Exiting User Program Mode
When you are done programming or erasing
User Codes, press C to exit. The Armed,
Status, and H lights will stop flashing, and you
can test your new User Code. IMPORTANT:
You MUST exit User Program Mode before
testing your new User Code.
GEM-P800 Commands
User Commands
A1 Bell Test
Enter this command to turn on the Bell, keypad
sounder and keypad LED's for 2 seconds. The
battery is tested during a Bell Test, and automatically every *24 hours to ensure proper battery operation under load. The Alarm output
requires a battery in order to supply the specified output. If the battery cannot sustain the
load, a low battery indication will be displayed.
A battery test is also performed on power-up
after a 3 minute delay.
*A battery test occurs every 4 hours when
Household Fire [96-3] has been selected.
D Easy Arm
Press this key to arm the panel. To disarm the
panel a valid Arm/Disarm code must be entered.
Requires Easy Exit/Easy Arm [21-2] to be enabled.
E
Interior
Enter this command to bypass all Exit/Entry Follower Zones or Home/Away Zones (only if the
system is programmed exclusively for Home/
Away with Delay zones).
F
Instant
Enter this command before or after arming to
remove the entry delay on Entry/Exit Zones.
The keypad ARMED LED will flicker rapidly.
Faulting a Exit/Entry Zone will result in an immediate alarm.
A5
Chime ON/OFF
Enter this command to turn chime ON/OFF.
The Keypad will chime on any zone that has not
been selected as an Exit/Entry Follower Zone,
Home/Away with Delay Zones, or 24 Hour Zone.
A8
+ User 1 Code - User Program
ready, tell the installer to arm, then disarm.
Then enter A6 in order to establish a
connection. Phone connection to installer will
go "dead" as downloader and panel connect.
Mode
A7
A9
Keypad Sleep Mode ON/OFF
Enter this command to turn the keypad sounder
ON/OFF. When the keypad is in Sleep mode all
keypad sounds will be silenced except for keypad feedback beeps and Keypad Sounder on
Alarm.
User Commands - Optional
A0
Easy Exit
If enabled in Dealer programming, enter this
command while the panel is Armed to allow 3
minutes to exit the premises through Exit/Entry
and Exit/Entry Follower Zones.
A3
Access on PGM
If enabled in Dealer programming, enter this
command to activate the PGM output (Terminal
15) for 5 seconds.
Dealer Commands
A6 Download
(Programming Required)
Establish a connection between the PCD phone
line and the Control Panel phone line. When
Fault Find ON/OFF
Hardwired Zone Operation
Enter this command to turn Fault Find ON/OFF.
While in Fault Find mode, the loop response for
all zones will be set to the faster response of 40
ms. The keypad will beep for .25-seconds when
hardwired zones are faulted and for 1-second
when zones are restored.
Wireless Operation
(Signal Strength)
While in Fault Find mode the keypad will provide
an audible (Table 6) and visual (Figure 5) indication of each transmitter's signal strength. The
signal strength metering is based on a scale of 4
to 10, with 4 being marginal and 10 being excellent.
The keypad will beep out a number, from 1-4,
corresponding to the signal strength of the transmitter. See Table 6. Each beep is 1-second
long. The keypad will sound a short beep for
transmitters with signal strengths of 3 or less.
SIGNAL STRENGTH
KEYPAD SOUNDER
3 or less
.25s BEEP
4
BEEP
5
BEEP BEEP
6-7
BEEP BEEP BEEP
8-10
BEEP BEEP BEEP BEEP
TABLE 6 AUDIBLE SIGNAL STRENGTH INDICATION
1
Signal Strength = 4
1 2
Signal Strength = 5
1 2 3
Signal Strength = 6-7
1 2 3 4
Signal Strength = 8-10
FIGURE 5 VISUAL SIGNAL STRENGTH INDICATION
Signal Strength Logging Mode
The Signal Strength Logging Mode is a troubleshooting tool which allows the collection of signal strength information for all transmitters on
the system. Normally the Signal Strength of Supervisory Signals are not logged; during Signal
Strength Logging Mode the signal strength information for all supervisory signals received over
a two hour period will be saved to the LOG.
Local Activation
Enable [92-4=ON], this will initiate a two hour
test period where all supervisory signals will log
signal strength information.
11
WI850D GEM-P800 Installation Instructions
Remote Activation
Using NAPCO's Quickloader Software
(Version 3.26 or higher), follow the instructions below:
From the Status Screen
Press F6
Select Miscellaneous Control
Select Enable Signal Strength Logging
Uploading Signal Strength Information
from the Log
After approximately (2) two hours, reestablish a connection with the panel. Signal strength log information ranges from 1
to 10. The logging of signal strength should
appear similar to the sample LOG below:
06/01/09 17:44
06/01/09 17:42
06/01/09 15:23
06/01/09 15:13
06/01/09 15:13
06/01/09
06/01/09
06/01/09
06/01/09
06/01/09
14:27
14:25
14:25
14:25
14:24
06/01/09 14:24
06/01/09
05/07/09
05/07/09
05/07/09
13:13
12:06
12:06
11:55
05/07/09 10:21
12
QL: Full Program Uploaded
QL: Technical Connection
(callback) Technician 2
Transmitter Status: GEM_SMK 1
(7A0DB5): SS=7
Transmitter Status: GEM_SMK 2
(768447): SS=8
Transmitter Status: Zone 2,
SS=6
Trouble: RF Link, GEM_RECV 1
Panic: Keypad
Panic: Keyfob 1(933780) SS=8
Dealer Program Mode Entered
Instant: Keyfob 1(933780)
SS=8
QL: Connection Terminated (10
MIN T/O)
QL: Full Program Downloaded
Open: User 2
Close: EasyArm
Trouble Restore: Low Battery,
GEM_SMK 2(768447) SS=8
Transmitter Status: GEM_SMK
(7A0DB5): SS=6
Zone Features
[00] Exit/Entry Zones
Delay allows exit and entry through an Exit/
Entry Zone after the system is armed without setting off an immediate alarm. Exit Delay allows the user to leave the premises
after arming. Entry Delay allows the user
time to enter and disarm. The entry delay
may be canceled by pressing F..
[01] Home/Away with Delay Zones
Zones that automatically bypass at the expiration of the exit delay if the EXIT/ENTRY
zone(s) are not violated. Zones of this type
have a three (3) minute power-up delay,
and do not display or cause an alarm if
faulted when the system powers up. Pressing the C key cancels the 3 minute timer.
If Exit/Entry zone(s) are violated during the
exit delay, zones programmed as Home/
Away with Delay Zone(s) will have a fixed
20-second entry delay, if violated before the
Exit/Entry zone.
To eliminate this fixed 20-second entry delay, also program zones as Exit/Entry Follower Zones [02].
To return protection to zones of this type,
press BC from the keypad or M or
N from a Keyfob.
Program the Keyfob
AUX 1 or AUX 2 button for Full Set [81-7].
NOTE:
If A0 is Entered during Exit Time, Home/Away with
Delay Zones will be automatically bypassed, even if the
Exit/Entry Zone is violated. Easy Exit/Easy Arm [22-2] must
be enabled.
[02]Exit/Entry Follower Zones
Entry Delay allows the user time to enter and
disarm. Allows exit after the panel is armed
without setting off an immediate alarm and
allows entry only if an Exit/Entry Zone [00]
has been violated first. Zones of this type
have a three (3) minute power-up delay, and
do not display or cause an alarm if faulted
when the system powers up. Pressing the
C key cancels the 3 minute timer.
Group Bypassing - Zones programmed as
Exit/Entry Follower Zones will be Group bypassed if the E key is pressed while disarmed or within the Exit Delay.
Auto Interior Bypassing - Also program
zones as Home/Away with Delay Zone(s)
[01] to automatically bypass at the expiration
of the exit delay if the EXIT/ENTRY Zone(s)
are not violated during the exit delay.
[03]Auto-Bypass Reentry Zones
Zones programmed as this zone type are
permitted to be faulted at the time of arming.
Once the zone is restored, while the control
panel is still armed, the zone will automati-
cally be unbypassed and any subsequent
violations of the zone will cause an alarm
condition.
[04] 24-Hour Protection
A zone that provides protection at all times,
whether or not the system is armed.
[05] 40 ms Loop Response
Normally loop response is 750 ms, select
this option to change the loop response to
40 ms. The slower the loop response, the
less sensitive the system will be to intermittents (swingers). The programming option
is not permitted for UL installations.
[06] Open Circuit Zones
Program this zone type if unsupervised normally open circuit devices are required The
programming option is not permitted for UL
installations.
Normally Open Zone Wiring
3.9K
2.2K
Wire the normally
open contact
as shown (Zone 4).
EZ Zone Doubling™
resistor is required.
Program the
zone for
Open Circuit [06] operation.
(Z)
ZONE 4
(E)
ZONE 1
[07] Burg (Steady) Output
Enables the Bell Output on a zone trip for
each zone selected. The Bell Output will
remain ON for the length of time programmed for Burg (Steady) Output [07] or it
will remain ON until turned off by entering a
valid Arm/Disarm Code; 0 means output will
stay ON until reset.
[08] PGM Output
Enables the PGM Output on a zone trip for
each zone selected. The PGM Output will
remain ON until reset.
[09] Selective Bypass
If programmed, selected zones will be able
to be bypassed by the User. By default, all
zones are permitted to be bypassed.
System Times
[10] Exit Delay
The delay time which permits exit through
an Exit/Entry Zone [00] after the system is
armed, allows a user to leave the premises
without setting off an immediate alarm. Exit
Delay may be programmed for up to 255
seconds (4¼ minutes); a value of 0 defaults
to 60 seconds.
[11] Entry Delay
Delay time permits entry through Exit/Entry
Zone(s) after the system is armed without
setting off an immediate alarm. Entry Delay
allows the user time to enter and disarm the
system. Upon entering, the keypad sounder
will sound a steady tone (Entry Sound) to
remind the user to disarm the system. Entry Delay Time [11] may be programmed for
up to 255 seconds (4¼ minutes); a value of
0 defaults to 30 seconds. Entry Delay may
be canceled by pressing F before or
after arming.
[12] Burg (Steady) Output Time-out
Can be programmed from 1 to 255 min (4¼
hours); 0 means output will stay ON until
turned off by entering an Arm/Disarm Code.
[13] Fire (Pulsed) Output Time-out
Can be programmed from 1 to 255 min (4¼
hours); 0 means output will stay ON until
turned off by entering an Arm/Disarm Code.
[14] Test Timer Interval
Program the interval, in days, between Test
Timer reports. Test Timer Interval may be
programmed from 1 to 255 days.
[15] Line Cut Time-to-Fail
Enable this feature by programming the
delay time required to declare a line cut failure. Programming 000 will disable line cut
detection.
[16] Wireless Supervisory Timer
A transmitter will send a transmission every
time it is tripped; when there is no activity,
the transmitter sends a supervisory transmission about once an hour. If the receiver
FIGURE 6 OPEN CIRCUIT W IRING
13
WI850D GEM-P800 Installation Instructions
does not receive any signal (either a trip or a
status) from a transmitter in the time specified, a system trouble 'RF Supervisory Failure' will be indicated at the keypad. Timer is
programmable from 1-26 hours; 0 means
NO supervision. Note: Wireless Supervisory Timer must be set to 10 hours.
[17] Wireless Smoke Supervisory Timer
A smoke detector will send a transmission
every time it is tripped; when there is NO
activity, the smoke detector sends a supervisory transmission about once an hour. If the
receiver does not receive a signal (either a
trip or a status) from a transmitter in the time
specified, a system trouble 'RF Supervisory
Failure' will be indicated at the keypad. The
Supervisory timer is programmable from 1-8
hours; 0 means NO supervision.
[18] Test Timer Offset
Enter the time, in hours, that a Test Timer
will be reported after Dealer Mode has been
exited. With the default value of 12, the test
timer will be sent 12 hours after exiting
Dealer Mode. The test timer can also be
offset using NAPCO PCD3000 Downloading
Software. On power up the test timer is sent
immediately. Follow the commands below
to offset the test timer using Quickloader
Software:
From the Status Screen
Press q
Select Miscellaneous Control
Select Test Timer Offset
14
Enter
New Test Timer Offset: 12 hours
Enter u to advance the test timer due in
time by 12 hours.
System Features
[20] Keypad Features 1
(1) Enable Keypad Fire (7G)
Additional Programming required:
Select reporting to Telco 1 [36-1] or Telco 3
[56-1].
(2) Enable Keypad AUX (8G)
Additional Programming required:
Select reporting to Telco 1 [36-2] or Telco 3
[56-2].
(3) Enable Keypad Panic (9G)
Additional Programming required:
Select reporting to Telco 1 [36-3] or Telco 3
[56-3].
(4) Enable Ambush - If enabled, the 8th
User Code will send an Ambush report
when entered to disarm the system.
Additional Programming required:
Program User 8 Arm/Disarm Code.
Select reporting to Telco 1 [36-2] or Telco 3
[56-2].
UL Installations: If Keypad Fire [20-1] is
enabled, the keypad must be mounted
within (3) three feet from the Control Panel.
[21] Keypad Features 2
(1) Audible Panic - Keypad Panic will not
turn the Bell on unless this option is programmed.
(2) Exit/Entry with Urgency - select to
give an audible indication of Exit and Entry
times. During the last 10 seconds of entry
and exit time, the keypad sounds a distinct
sound to indicate the premises must be left
or the panel must be disarmed.
(3) Display Bypassed (Armed) - Select to
display bypassed zones while the panel is
armed.
(4) Disable Code Entry Beeps - Program
to disable keypad beeping on valid code and
function entries.
[22] Miscellaneous Features 1
(1) Abort Delay - Program to allow a 15
second Delay (except 24 Hour Zones) after
a zone trip before reporting. Disarm the
system within 15 seconds to prevent reporting.
(2) Easy Exit/Easy Arm- Enables
A0 command. While the system is
armed, entering this command allows 3 minutes to Exit through Exit/Entry and Exit/Entry
Follower Zones. Enabling this option also
enables Easy Arm, press the D key to arm
the system.
(3) Swinger Shutdown - Automatically
disables armed zones with excessive alarm/
restores (swingers). Non-24-Hour Protection zones: allows only 3 alarms and 2 restores per zone per arming before the zone
is disabled.
(4) Bell on Line Cut (Armed) - Program to
turn the Bell Output on if the telephone line
has been cut while the panel is armed.
[23] Programmable Output Features 1
(1) Audio Verification - Program to activate the PGM during reporting. Select specific zones for audio verification by programming the required zones in PGM Output
[08], PGM Features 2 [24] and PGM Features 3 [25]. Connect the PGM to the
VeriphoneTM trigger low input.
(2) Access Output - Activates the PGM
output for 5 seconds using the A3
command.
(3) Follow Keypad Sounder - The following keypad sounds will activate the PGM
output: Entry Sounder, Keypad Pulsing
Sounder, Keypad Output on Alarm, Chime,
Fault Find.
(4) Keyfob/Keyswitch Chirp - Program to
chirp the PGM Output (1) one time when the
panel is armed or (2) two times when the
panel is disarmed. Wire as shown in Figure 7.
PGM
BLK
+AUX
RED
K1
[24] Programmable Output Features 2
(1) Fire - Program to activate the PGM on
a Fire alarm.
(2) AUX - Program to activate the PGM on
a AUX alarm.
(3) Panic - Program to activate the PGM
on a Panic alarm.
(4) Test Timer - Program to activate the
PGM during a Test Timer report.
[25] Programmable Output Features 3
(1) AC Fail - Program to activate the PGM
on the loss of AC. (15 minute delay)
(2) Low Battery - Program to activate the
PGM on a Low Battery condition.
(3) *Trouble - Program to activate the
PGM on a Trouble condition.
(4) Armed - Program to activate the PGM
when the panel is Armed. The PGM output
will flash when the panel has gone into
alarm.
*Includes Bell Cut, Fire Trouble, Receiver
Fail-to-Respond, Receiver Tamper, Receiver JAM, Wireless Smoke Low Battery,
Wireless Smoke Supervisory Fail.
[26] Miscellaneous Features 2
COM
+AUX
N/C
N/O
Siren Driver
Steady Input
(1) Momentary Keyswitch Arming - Typically, connect a normally-open Keyswitch
across the zone AND its 3.3K zone-doubling
resistor.
(2) Reserved.
(3) Inhibit Fail-to-Communicate Display - This option prevents the keypad from
either indicating or sounding when a Fail to
Communicate has occurred.
(4) Inhibit Low Battery Display - Program
to inhibit the Low Battery Display at the keypad. Low Battery Reporting is not inhibited.
The programming option is not permitted for
UL installations.
Telephone Number 1 Programming
[30] Subscriber ID Number
For 4/2 format enter a 4 digit number. If 3/1
format is required, enter a 3 digit number,
then press the F key to blank the last
digit.
[31] Telephone Number 1
Program the phone number to be dialed for
Telephone Number 1. Program the number
directly, just as it is entered on a TouchTone
phone. A fixed Dial Tone Detection (E) is
included prior to the Dialing Prefix (Block
Number 44). Programming an E is not required for Telco 1, Telco 2 and Telco 3. If
dial tone detection is not desired select No
Dial Tone Detection in Communicator Features [46-1].s Use the F key to blank
out remaining digits in the phone number.
[32] Receiver Format
Select the receiver format to be used to report for Telephone Number 1: Program a 0
FIGURE 7 KEYFOB/KEYSWITCH CHIRP
15
WI850D GEM-P800 Installation Instructions
to disable reporting to Telco 1.
[0] Disabled
[1] Ademco Slow
[2] Radionics Slow
[3] Silent Knight Fast
[4] Universal High Speed
[5] Reserved
[6] Point ID
[7] Pager
[33] Receiver Options
(1) 2300 Hz HS / Kissoff - Select 2300 Hz
Handshake and Kissoff.
(2) Sumcheck - Only used for the following Receiver Formats: Ademco Slow, Radionics Fast, Silent Knight Fast and Universal
High Speed. This is a sophisticated data
format used to enhance the speed and
check the accuracy of the received transmission. This format should be used whenever the central station has this capability.
Instead of sending a second round to verify
correct data, the panel sends a Sumcheck
digit after sending the Subscriber ID and
Alarm Code.
(3) Single Digit - 3/1 Format. 3-digit Subscriber ID number and a 1-digit Alarm Code
will be transmitted.
(4) No Handshake - (All receiver formats
except Pager Format)
If programmed no Handshake / Kissoff is
required by the panel.
[34] Zone Report, Telco 1
Select zone(s) required to send an alarm
report to Telephone Number 1.
[35] Zone Restore Report, Telco 1
16
Select zone(s) required to send a restore
report to Telephone Number 1. The zones
will send a restore after Bell time-out, unless
programmed as silent zones.
[36] System Reporting, Telco 1
(1) Keypad Fire - Program to activate a
Keypad Fire report (7G).
(2) AUX/AMBUSH - Program to activate
an AUX or AMBUSH report (8G).
(3) Panic - Program to activate a Panic
report (9G).
(4) Test Timer - Program to activate a
Test Timer report.
[37] System Reporting, Telco 1
(1) AC Fail Report - Program to activate
an AC Fail report (15 minute fixed report
delay).
(2) Low Battery Report - Program to activate a Low Battery report.
(3) *Trouble Report - Program to activate
a Trouble report.
(4) Fire Report - Program to activate a
Fire report.
*Includes Bell Cut, Fire Trouble, Receiver
Fail-to-Respond, Receiver Tamper, Receiver JAM, Wireless Smoke Low Battery,
Wireless Smoke Supervisory Fail. Point ID
format will report trouble(s) by device and ID
number.
[38] System Restore Report, Telco 1
(1) AC Restore - Program to activate an
AC Restore report.
(2) Battery Restore - Program to activate
a Battery Restore report.
(3) Trouble Restore - Program to activate
a Trouble Restore report.
(4) Fire Restore - Program to activate a
Fire Restore report.
[39] Opening/Closing Report, Telco 1
Select users required to send opening and
closing reports to Telephone Number 1.
Do not program for users that are intended
to send an Opening After Alarm (Cancel
Code) or Conditional Closing reports.
Backup Telephone Programming
[40] Subscriber ID Number (Telco 2)
For 4/2 format enter a 4 digit number. If 3/1
format is required enter a 3 digit number
then press the F key.
[41] Telephone Number 2
Program the phone number to be dialed for
Telephone Number 2. A fixed dial tone detection (E) is included prior to the Dialing
Prefix [44]. Dial tone detection can be disabled by programming No Dial Tone Detection [46-1]. To program any additional delay
enter a "D" where required in the phone
number.
[42] Receiver Format (Telco 2)
Select the format that will be used to report
for Telco 2 (Backup reporting). Refer to
section [32].
[43] Receiver Options (Telco 2)
Refer to section [33] Receiver Options.
[44] Dialing Prefix
Dialing prefix for Telco 1, Telco 2, and Telco
3. Program if using an Outside access number.
[45] Communicator Features 1
(1) Communicator Enabled - Program to
enable the communicator.
(2) DTMF with Rotary Backup - The first
attempt to communicate is dialed using the
TouchTone method of dialing, subsequent
attempts are dialed using the pulse method
of dialing. Disable this feature to dial using
only rotary dialing.
(3) DTMF only - All attempts to communicate dial using the TouchTone method of
dialing.
(4) Backup Reporting to Telco 2 - After 2
attempts are made to communicate to Telco
1 the backup phone number is dialed (Telco
2).
[46] Communicator Features 2
(1) No Dial Tone Detection - Program to
disable dial tone detection for Telco 1, Telco
2 and Telco 3.
(2) 2:1 Rotary Dialing - Changes the
make break ratio when rotary dialing from
1.5:1 to 2:1.
(3) Backup if < 4 attemps - If Backup
Reporting [45-4] has been enabled, the
communicator will use Telephone Number 2
[41] for the remaining retries when there are
less than 4 retries remaining.
(4) Reserved
Pager Programming
If Pager Format ([32]and/or[42]and/or[52] =
7) is selected, pager data will be displayed
as shown in Figure 8. If Pager Format is
selected 4/2 format must be programmed
and Sumcheck is not permitted. If a PIN
number is required refer to Leading Digits
[47].
000 033-1234
Leading Digits
Report Code
Subscriber ID Number
FIGURE 8 DEFAULT PAGER DISPLAY
Pager Alarm data is the same as 4/2 format
with the exception that the 2 digit Report
Code is transmitted before the 4 digit Subscriber ID.
NOTE:
Digits in Report Codes and subscriber IDs that are programmed with "B" through "F" will be converted to "0"s.
[47] Leading Digits
Pager PIN Number - If a PIN number is
required by the paging system, program the
PIN number in the Leading Digits location.
See sample program below.
If a 7-digit PIN number is required, program
the panel as follows:
[31]/[41]/[51] - Pager Telephone number
[32]/[42]/[52] - Select Pager Format
[47] - X X X X X X X C
7-digit PIN Number
Terminating Digit (#)
Leading and Trailing digits can be letters B,
C or D. B = the * button on a telephone, C =
the # button on a telephone, D = 2 second
delay.
[48] Trailing Digits
Transmitted after alarm data. Refer to section [47] for programming information.
[49] Pager Options
(1) Skip Alarm Data - Once pager format
is selected, program this option to skip
alarm data. If this option is selected, all the
programmed Leading and Trailing digits are
17
WI850D GEM-P800 Installation Instructions
sent, but the event code and subscriber ID
are not transmitted. With this option selected, a telephone number programmed in
Leading Digits or Trailing Digits would send
the telephone number to the pager each
time a report is sent.
(2) Reserved
(3) Reserved
(4) Reserved
Telephone Number 3 Programming
[50] - [59]
Programming is the same as for Telco 1.
Program to split/double report to Telco 3.
Refer to sections [30] through [39].
Report Codes
[60] Zone Report Codes
Report Code for Zones 1 through 8.
4/2 format - The Zone Report Code is the
1st digit of the report code sent, the second
digit is the zone number of the reporting
zone. For example, if zone 2 has a report
code of 3, the report code would be 32.
3/1 format - Sends only the report Code
and does not append it with the zone number.
18
[61] Point ID Report Codes
Point ID Report Codes are defaulted to Burglary for zones 1 through 8. Optionally,
Point ID codes for zones 1 through 8 can be
programmed as follows:
[1] Fire
[2] Panic
[3] Burglary
[4] Holdup
[5] General Alarm
[6] Reserved
[7] Gas Alarm
[8] Heat Alarm
[9] Reserved
[A] Auxiliary
[B] 24 Hour
Fire, Keypad AUX, Keypad Panic, Test
Timer, AC Fail, Low Battery, Trouble and
Fire.
[64] System Restore Code
The code sent when a system condition
restores. The second digit of the 2-digit
restore code is the second digit of the System Report Code [63]. For example, if a
Low Battery System Report Code is F8 the
Battery Restore would be E8 (4/2 format).
[65] Opening and Closing Codes
[62] Zone Codes
[62-1] Restore code - Zones 1 through 8.
The second digit of the restore code is the
zone number of the restored zone. For example, if the Zone Restore Code [62] is programmed to E, the restore code for that
zone would be E4 (4/2 format).
[62-2] Trouble Code - Conditional Closing
Reports. Zones that are bypassed at the
time of arming send this code along with the
zone number of the bypassed zone(s). For
example a conditional closing by User 2,
with zones 2 and 3 bypassed would be as
follows:
1234
C2
F2
F3
[63] System Report Codes
Program a 2-digit report code for Keypad
Program Opening and Closing Codes for
Users 1 through 8. The second digit of the
report code is the number of the user that
armed or disarmed the system. For example, if the Closing Code [65] is programmed
with a C, the closing code for User 2 would
be C2 (4/2 format).
[66] Ambush Report Code
Program a 2-digit report code for Ambush.
To send an ambush report, program a User
Code for User 8, Program report User 8 as
Ambush [20-4] and Select reporting for
Telco 1 [36-2] and/or Telco 3 [56-2].
Enhanced Communicator Features
[67] Telephone Number 1
(1) Opening After Alarm (Cancel Code) When enabled, all users that are not selected to report on Opening/Closing [39] will
report an Opening only when opening after
an alarm has occurred.
(2) Conditional Closing Telephone 1 When enabled, all users that are not selected to report an Opening/Closing ([39],
[59]) will report a Closing only when zones
have been bypassed. The Zone Trouble
Code [62-2] is used to report zones that
have been bypassed at the time of the closing report.
(3) Reserved
(4) Reserved
[68] Telephone Number 3
(1) Opening after Alarm (Cancel Code) see [67-1].
(2) Conditional Closing Telco 3 - see
[67-1].
(3) Reserved
(4) Reserved
Wireless
Up to two receivers can be wired to the
GEM-P800. Each wireless transmitter can
be mapped to a zone. Only 1 wireless de-
vice is permitted per zone, however, the use
of both hardwired and wireless on a zone is
permitted.
To Map a transmitter to a zone:
1. Enter the Programming Block Number
that the transmitter is to be mapped to.
2. Enter the 7-digit RF ID number directly,
just as it is shown on the device label.
After the 7th digit is entered the keypad
will beep.
A transmitter will send a transmission every
time it is tripped. The transmitter also sends
a supervisory transmission about once
every hour. If the receiver does not receive
a signal from a transmitter in the time programmed in Wireless Supervisory Timer, a
system trouble 'RF Supervisory Failure' will
be indicated at the keypad.
Program Wireless Supervisory Timer [16] to
change the supervisory time from the default
of 12 hours.
The Signal strength of a transmitter can be
checked at the keypad (see A7
Fault Find Mode) or saved to the LOG (see
Signal Strength Logging Mode - pg. 11).
[71-78] Wireless Transmitters
Enter the RF ID# and the point number that
is to be mapped to the zone.
Programming Example
Map point 1 of a window door transmitter
with an RF ID# of 0012B0:0 to Zone 3.
1. Enter Dealer Mode.
2. Enter C (beeps) 73 (beeps)
3. Enter
0 1 2 G 2 0
0
4. Enter 1 (beeps)
Note: If the RF ID# in step 3 is not entered
correctly the keypad will emit a 1 second
tone indicating incorrect entry.
Repeat
steps 2 - 4 above.
[81] - [84] Wireless Keyfobs
The GEM-KF is a hand held wireless transmitter capable of Arming and Disarming the
control panel and/or activating 2 Auxiliary
Functions. To activate the auxiliary functions, press and hold the M or N key for
1.5 seconds (see WI752 for more information).
Enter the RF ID# and AUX 1 and AUX 2
options for each Keyfob.
AUX 1 & AUX 2
Programming Options:
1 Panic
Program a 1 in the AUX 1 and/or AUX 2
option to initiate a panic alarm when the M
or N buttons on the Keyfob are pressed.
Additional programming required:
Keypad Panic (9G) [20-3]
Panic Report to Telco 1[36-2] and/or Telco 3
19
WI850D GEM-P800 Installation Instructions
[56-3].
Audible Panic (Optional) [21-1]
2 AUX
Program a 2 in the AUX 1 and/or AUX 2
option to initiate a AUX alarm when the M
or N buttons on the Keyfob are pressed.
Additional programming required:
Keypad AUX (8G) [20-2]
AUX Report to Telco 1[36-2] and/or Telco 3
[56-2].
3 Bell ON
Program a 3 in the AUX 1 and/or AUX 2
option to turn the Bell ON when the M or
N buttons on the Keyfob are pressed.
Press the L button to turn the Bell OFF.
4 PGM
Program a 4 in the AUX 1 and/or AUX 2
option to activate the PGM Output when the
M or N buttons on the Keyfob are
pressed. Press the L button to turn the
PGM Output OFF.
5 Instant
Program a 5 in the AUX 1 and/or AUX 2
option to activate Instant Mode when the
M or N buttons on the Keyfob are
pressed.
6 Access on PGM
20
Program a 6 in the AUX 1 and/or AUX 2
option to activate the PGM Output for 5 seconds when the M or N buttons on the
Keyfob are pressed.
Addition programming required:
Enable Access Output [23-2]
7 Full Set System
Program a 7 in the AUX 1 and/or AUX 2
option to Fully Set the System when the K
and the M or N buttons on the Keyfob
are pressed, or when the M or N buttons are pressed when the system is armed
with Exit/Entry Follower Zones or Home/
Away with Delay Zones that have been bypassed.
8 Interior
Program an 8 in the AUX 1 and/or AUX 2
option to Bypass Exit/Entry Follower Zones
or Home/Away with Delay Zones when the
M or N buttons on the Keyfob are
pressed (only if the system is programmed
exclusively for Home/Away with Delay
Zones).
[85] - [88] Wireless Smoke Detectors
Enter the RF ID# of the smoke detector.
A wireless smoke detector sends a supervisory transmission about once every hour. If
the receiver does not receive a signal from a
transmitter in the time programmed in Wireless Smoke Supervisory Timer, a system
trouble 'RF Smoke Supervisory Failure' will
be indicated on the keypad.
Program Wireless Smoke Supervisory Timer
[17] to change the time from the default time
of 8 hours. Refer to Household Fire [96-3].
Note: Mark Smoke Detectors (Smoke 1
through Smoke 4) in order to identify them in
the event of a supervisory or battery failure.
If Household Fire [96-4] is selected, Wireless Smoke Supervisory Time is fixed at 4
hours.
Downloading
[90] Callback Telephone Number
Program the phone number of the
downloading computer to be dialed by the
panel during a high security download.
[91] Ring Count
Program the number of rings before the
panel will pickup.
Ring Method [92-1]
(Downloading Features) must also be selected.
[92] Downloading Features
(1) Ring Method - Enable the ring method
of downloading. The panel will pick-up on
the number of rings programmed in Ring
Count [91].
(2) Answering Machine Override - Using
the downloading computer, call the panel.
When the operator has determined that the
panel has received 1-2 rings, pressing the
u key will cause the downloading computer to immediately re-dial the panel. The
panel will pick-up on the first ring.
(3) Function 6 Download - Select to enable the A6 method of downloading
(pg. 8).
(4) Signal Strength Test Mode - Program
to initiate a 2 hour test period. The signal
strength information for all supervisory signals received over a two hour period will be
saved to the LOG.
[93] Auto Download ID Number
Enter the Number that is used by PCPreset
when downloading using Site Initiated Auto
Downloading (A6).
The requirements for Site Initiated Auto
Downloading are as follows:
1. Download Computer running PCPreset.
2. Program the telephone number of the
Download Computer in location [90]
Callback Telephone Number.
3. Program location [93] with the number
of the PCPreset account that is to be
downloaded.
PCPreset
1. Create the GEM-P800 account to be
2.
3.
4.
5.
downloaded using PCD3000 Quickloader Software.
Create a List using PCPreset.
Select the account by pressing tt.
Select the desired account from the list
of PCD3000 accounts available. (The
location in the list is the Auto Download
ID Number [93])
Tag the list by entering aD
(download)
Enter Standby Mode by entering o.
The Computer is now in STANDBY
Site
At the site perform the following three steps:
1. Arm the panel.
2. Disarm the panel.
3. Enter A6. The panel will now
call the download computer running
PCPreset. PCPreset will answer the
call, establish a connection, and then
download the account that matches the
Auto Download ID Number [93] with the
account of the same number in the list
that PCPreset is currently running.
Dealer Programming
[94] Dealer Code
The default Dealer Code is 4567. Program
a new 4-digit Dealer Code. When the panel
is defaulted the Dealer Code will be
changed back to the default Dealer Code of
4567 only if Dealer Code Lockout [96-1]
has not been programmed.
[95] User 1 Code
The 1st User code is a program code as
well as an Arm/Disarm code. The default
User Code is 1234. If User 1 Code Lockout
is programmed the User 1 Code cannot be
programmed from User Program Mode.
[96] Dealer Options 1
(1) Dealer Code Lockout - Program to
prevent the Dealer Code from changing with
a panel default.
(2) User 1 Code Lockout - If programmed
the User 1 Code cannot be programmed
from User Program Mode.
(3) Household Fire - Activates the following UL required features:
There is a 4 hour re-sound of wireless
Smoke Low Battery and wireless Smoke
Supervisory system troubles.
• An active System Battery test performed
every 4 hours instead of 24 hours and
Wireless Smoke Supervisory Timer is
set to 4 hours.
• Fire Bell Timing is March Time.
• Wireless Smoke Supervisory Time is
fixed at 4 hours.
(4) Fire Trouble on Fire LED - Normally
21
WI850D GEM-P800 Installation Instructions
all troubles are displayed on the H SYSTEM
TROUBLE LED, including Fire Trouble. If
required Fire Trouble can be displayed on
the Fire LED. Fire Trouble is indicated by a
steady I Fire LED.
[97] Dealer Options 2
(1) International Dialing Protocol - No
dialing if no dial tone, 60 s between attempts
and 4 s wait for dial tone.
(2) Invert Bell Output - Inverts the Bell
polarity and removes supervision from the
bell circuit.
(3) System Trouble Auto Restore - Normally, System troubles require acknowledgment (View System Trouble) in order to restore. If this option is selected troubles will
restore without requiring acknowledgment.
(4) User 1 Code-Program only - If enabled User 1 Code will function only as the
User Program Code and will not Arm/Disarm
the panel.
Note: All programming within Programming
Blocks [96] & [97] will not change if the
panel is defaulted.
[98] Number of Re-Dials
The Number of re-dial attempts made by the
panel before indicating a Fail-toCommunicate (System Trouble 1-3).
22
System Troubles
are no more system troubles to view, the system
will return to normal operation.
Use the System Trouble chart on the following
page to determine the specific System Trouble
(s).
EXAMPLE
During normal panel operation the H SYSTEM
TROUBLE LED has the following two modes of
operation:
- LOW BATTERY SYSTEM TROUBLE DISPLAY
Enter A4 to enter System Trouble mode
and determine the specific trouble. Press any key to
view all system troubles.
GEMINI
STEADY
FLASHING
1-7 possible trouble
groups, AC is present
1-7 possible trouble
groups, AC is not present
Viewing System Trouble(s)
Press the A4 key on the keypad.
To determine the System Trouble Group Number, count the number of times the H SYSTEM
TROUBLE LED blinks. The keypad sounder will
beep at the same rate that the H SYSTEM
TROUBLE LED blinks.
To determine the System Trouble, note the
zone LED that is ON. Look up the specific system trouble on the chart on the following page.
The H SYSTEM TROUBLE LED and keypad
sounder will continue to flash and beep. To view
the next System Trouble, if any, press the E
key. Continue pressing the E key, if there
H
2
System Trouble Reporting
TUS
ST A
ED
ARM
Flashing
(System Trouble
Group Number)
Beeping
(System Trouble
Group Number)
Zone LED(s) is ON
indicates
(Specific Trouble)
ZONE LED . For example, a wireless low battery
on zone 2 would beep the keypad sounder 3
times and turn on zone 2 LED.
Audible System Trouble Indication - For all
system troubles, except when the only system
trouble is the loss of AC, the keypad will beep
once every 10 seconds. The keypad will continue to beep until the reset button is pressed or
the trouble has been acknowledged by pressing
the C key.
System Trouble
Group #
Keypad SYSTEM Trouble
LED is flashing 1 time
indicating System Trouble
Group 1.
Keypad Sounder beeps 1
time indicating System
Specific Trouble
Zone 2 LED is ON indicating
Low Battery. (1 Beep, LED 2)
The following system troubles, when enabled to
report to Telco 1 [37-3] or Telco 3 [57-3], will
send the report code programmed in Trouble
Report [63] if reporting using a pulse format:
System Trouble
Bell Cut
2-Wire Fire Trouble
Rcvr Fail-to-Respond
Receiver Tamper
Receiver JAM
Tx Low Battery
Tx Supervisory Failure
If reporting using Point ID, a unique code will be
sent for each of the following System Troubles.
System Trouble
FIGURE 9 SYSTEM TROUBLE EXAMPLE
Note: System Troubles Groups 3 through 7 System Trouble Groups that have a zone or
smoke detector associated with the trouble,
such as RF low battery. The zone(s) of the device with a low battery will be displayed by the
Pulse Report Code
F1
F1
F1
F1
F1
F1
F1
Bell Cut
2-Wire Fire Trouble
Rcvr Fail-to-Respond
Receiver Tamper
Receiver JAM
Point ID Report Codes
CODE 1 321 G00 ZN000-BELL 1 TROUBLE
CODE 1 373 G00 ZN000-FIRE LOOP TRBLE
CODE 1 382 G00 ZN000-SENSOR TROUBLE
CODE 1 145 G00 ZN000-EXP. MODL. TAMPER
CODE 1 373 G00 ZN000-FIRE LOOP TRBLE
A 300 (SYSTEM TROUBLE RST) code is sent if a restore is
reported after multiple troubles.
23
WI850D GEM-P800 Installation Instructions
System Troubles
Keypad Beeps or
Flashes
j SYSTEM
1 Beep
2 Beeps
24
Zone LED ON
System Trouble Condition
Cause/Action
1
AC Power Failure
This trouble will occur if AC power is not present. Ensure that the transformer is connected to an un-switched power
source.
2
Low Battery
If there has been a recent power failure, the battery may be partially depleted and must be recharged by the control
panel. If the trouble does not go away in 24 hours, replace the battery.
3
Communication
Failure/PCPreset Fail
The system was not able to report to central station. Check panel programming and telephone line wiring. The trouble will clear after it has been acknowledged by viewing the system trouble as long as the telephone line has passed a
line cut test (tested automatically by the panel). The Panel did not successfully connect and download/upload with the
computer running PCPreset - check Auto Download ID number, Callback Number or PCPreset Setup.
4
Telephone Line Cut
The telephone line has failed. If telephone service has been temporarily interrupted, the trouble will clear when restored and acknowledged by viewing the system trouble.
1
Bell/Siren line Cut
There is a problem with the Bell or Siren wiring. EOL2.2K resistor must be installed.
2
2-wire Fire Trouble
There is a problem with the wiring of the Fire Zone.
3
Rcvr Fail-to-Respond/Rcvr
Tamper
The receiver is not responding to the panel. The red LED on the receiver should be flashing, refer to WI850. The
cover is off the receiver causing a tamper signal to be transmitted.
4
Receiver Jam
A signal is blocking the normal reception of transmissions from the wireless devices. Ensure that the green LED on
the receiver is not on continuously, refer to receiver manual WI850.
3 Beeps
1-6
Wireless
Transmitter Low Battery
The battery in a wireless transmitter is low and should be replaced. This transmitter is on the zone corresponding to
the number of the lit zone light. The replacement battery for the GEM-TRANS2 door/window transmitter, GEM-PIR
motion detector and GEM-GB glass break detector is the Duracell DL123A 3 volt lithium. (2 required for the GEM-PIR
and GEM-GB). The GEM-DT Dual Technology Sensor requires 4 C cell alkaline batteries. Warning: Replace batteries only with the same type as specified above. Use of another battery may present a risk of fire or explosion. Do not
recharge or disassemble battery, or dispose of in fire.
4 Beeps
1-6
Wireless Transmitter
Supervisory Failure
The panel has not received a supervisory signal from the transmitter within the time programmed. Check Wireless
Supervisory Timer [16] Programming. Check the placement of the transmitter and receiver, refer to WI850.
5 Beeps
1-4
Wireless Smoke Detector Low Battery
The battery in a wireless smoke detector is low and should be replaced. This wireless smoke detector should be
marked with a number corresponding to the number of the lit zone light. The replacement battery is the Duracell
MN1604 9 Volt Alkaline (2 required). Warning: Replace batteries only with the same type as specified above. Use of
another battery may present a risk of fire or explosion. Do not recharge or disassemble battery, or dispose of in fire.
6 Beeps
1-4
Wireless Smoke Detector Supervisory Check Wireless Smoke Supervisory Timer [17] Programming. Check the placement of the wireless smoke detector
7 Beeps
1-6
The panel has not received a supervisory signal from the wireless smoke detector within the programmed time.
and receiver, refer to WI850.
Zone Trouble
The panel has one or more of the following 3 possible troubles: Zone Short, Transmitter Tamper or Dual Tech Self Test
Fail.
Troubleshooting
1.
3.
4.
5.
The Chime feature will automatically be
assigned to all zones, except for the following:
• Zones programmed as Exit/Entry
Followers
6.
7.
I short out the bell and the system
does not indicate Bell Trouble.
The Bell Supervision circuit is only designed to detect a "Bell Cut", it does not
supervise for a short on the Bell.
Where are the fuses?
The control panel incorporates advanced
circuitry which automatically limits the
current when an over current condition
exists without the use of traditional
fuses. The circuit will restore automatically when the over current condition is
corrected.
How do I activate Chime by Zone?
• Zones programmed as Home/Away
with Delay.
When using a piezo on the Bell Output, it constantly buzzes.
This is due to the fact that there is a constant loop current flowing through the
Bell circuit for supervision. To eliminate
this, cut resistor R26 which is located
directly above Terminal 9 just below the
heat sink.
How do I remove the Keypad Sounder
on Alarm?
The keypad sounder follows the Burg
Output. If you need to remove the Keypad Sounder, then you must remove the
Burg Output from that zone.
function which will indicate that the system is in an Alarm condition. If this output is being used to trigger a long range
radio, it can be converted to a steady
output with the use of a capacitor, negative to PGM Terminal 15, Pos to Aux.
Pwr. Term 12 (220mF Electrolytic Capacitor, 25 volts. Increase to 470mF if
necessary).
To Activate / Deactivate the chime
mode, press A5.
The bell output drops to about 3 volts
in alarm.
The battery/bell circuit is protected by a
PC board trace which may have burned
open by reversal of the battery leads. It
is on the back of the PC board just adjacent to the red & black battery leads.
Send in for service if this occurs.
2.
• Zones programmed for 24 Hour Protection.
The PGM Output Pulses in Alarm.
When the PGM lug of the control panel
is programmed for an Armed indication it
also incorporates an Alarm Memory
8.
How do I remove Keypad Sounder on
Alarm?
The keypad sounder follows the Burg
Output. If you need to remove the Keypad Sounder, then you must remove the
Burg Output from that zone.
9.
Transmitters not responding?
Open Transmitter case - Keypad should
go into X-Mitter Tamper Trouble. If not:
• Check Receiver Red LED should be
25
WI850D GEM-P800 Installation Instructions
flashing once approx. once a
ond.
sec-
• Check Receiver wiring.
• Check Programming of Transmitter
ID.
If Keypad does go into X-Mitter Tamper
Trouble, check:
• Transmitter point is programmed correctly.
• Transmitter is wired correctly:
• If using external switch, make sure it
is wired to point 1, and point 2 is
jumped out.
• If using internal reed, make sure J1
is cut and both Point 1 and Point 2
terminals are jumped out.
10. Keypad LED's Flicker.
The Keypad is not receiving a POLL
from the Panel.
Check Keypad wiring:
1. The Panel is in the process of being
Uploaded / Downloaded.
2. The panel is powering up. LED’s will
26
flicker until panel has reset and is
polling the keypad.
3. The connection from the control
panel to the keypad is open.
11. No Keypad Entry Sounder during Entry Time?
The keypad sounder is turned off with
the A9 command. This command will silence all Keypad sounds except keypad sounder on alarm. Enter
A9 to turn keypad sounds back
on.
12. No Keypad Chime?
The keypad sounder is turned off with
the A9 command. This command will silence all Keypad sounds except keypad sounder on alarm. Enter
A9 to turn keypad sounds back
on.
27
NAPCO LIMITED WARRANTY
NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be free from manufacturing defects in materials and workmanship for thirty-six months following the date of manufacture.
NAPCO will, within said period, at its option, repair or replace any product failing to operate correctly without charge to the original purchaser or user.
This warranty shall not apply to any equipment, or any part thereof, which has been repaired by others, improperly installed, improperly used, abused, altered, damaged, subjected to acts of God, or on
which any serial numbers have been altered, defaced or removed. Seller will not be responsible for any dismantling or reinstallation charges.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. THERE IS NO EXPRESS OR IMPLIED WARRANTY OF
MERCHANTABILITY OR A WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. ADDITIONALLY, THIS WARRANTY IS IN LIEU OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE
PART OF NAPCO.
Any action for breach of warranty, including but not limited to any implied warranty of merchantability, must be brought within the six months following the end of the warranty period. IN NO CASE SHALL
NAPCO BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE
LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT.
In case of defect, contact the security professional who installed and maintains your security system. In order to exercise the warranty, the product must be returned by the security professional, shipping
costs prepaid and insured to NAPCO. After repair or replacement, NAPCO assumes the cost of returning products under warranty. NAPCO shall have no obligation under this warranty, or otherwise, if
the product has been repaired by others, improperly installed, improperly used, abused, altered, damaged, subjected to accident, nuisance, flood, fire or acts of God, or on which any serial numbers have
been altered, defaced or removed. NAPCO will not be responsible for any dismantling, reassembly or reinstallation charges. This warranty contains the entire warranty. It is the sole warranty and any
prior agreements or representations, whether oral or written, are either merged herein or are expressly canceled. NAPCO neither assumes, nor authorizes any other person purporting to act on its behalf
to modify, to change, or to assume for it, any other warranty or liability concerning its products. In no event shall NAPCO be liable for an amount in excess of NAPCO's original selling price of the product,
for any loss or damage, whether direct, indirect, incidental, consequential, or otherwise arising out of any failure of the product. Seller's warranty, as hereinabove set forth, shall not be enlarged, diminished or affected by and no obligation or liability shall arise or grow out of Seller's rendering of technical advice or service in connection with Buyer's order of the goods furnished hereunder.
NAPCO RECOMMENDS THAT THE ENTIRE SYSTEM BE COMPLETELY TESTED WEEKLY.
Warning: Despite frequent testing, and due to, but not limited to, any or all of the following; criminal tampering, electrical or communications disruption, it is possible for the system to fail to perform as
expected. NAPCO does not represent that the product/system may not be compromised or circumvented; or that the product or system will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; nor that the product or system will in all cases provide adequate warning or protection. A properly installed and maintained alarm may only reduce risk of burglary, robbery, fire or
otherwise but it is not insurance or a guarantee that these events will not occur. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE, OR
OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. Therefore, the installer should in turn advise the consumer to take any and all precautions for his or her safety including, but not limited to, fleeing the premises and calling police or fire department, in order to mitigate the possibilities of harm and/or damage. NAPCO is not an insurer of either the property or safety of
the user's family or employees, and limits its liability for any loss or damage including incidental or consequential damages to NAPCO's original selling price of the product regardless of the cause of such
loss or damage.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion or limitation of incidental or consequential damages, or differentiate in their treatment of limitations
of liability for ordinary or gross negligence, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights which vary from
state to state.
THE FOLLOWING STATEMENT IS REQUIRED BY THE FCC.
This equipment generates and uses radio-frequency energy and, if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and
television reception. It has been type tested and found to comply with the limits for a Class-B computing device in accordance with the specifications in Subpart J of Part 15 of FCC Rules, which are
designed to provide reasonable protection against such interference in a residential installation.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: reorient the receiving antenna; relocate the computer with respect to the receiver;
move the computer away from the receiver; plug the computer into a different outlet so that computer and receiver are on different branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the Federal Communications
Commission helpful: “How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, DC 20402; Stock No. 004-00000345-4.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement