LSN Inverter specification sheet - Dual-Lite
D Series
Single-Phase Central Lighting Inverters
Catalog Number
Comments
FEATURES
Type
Application
Designed for indoor installation in commercial or industrial applications.
Operation
When normal utility-supplied power is present, the LSN model central lighting inverter
provides load-side line conditioning with "brownout" protection, and charges the system
batteries when required. When utility-supplied power is interrupted, or the voltage varies
from predetermined limits, the system will automatically and instantaneously transfer to
emergency mode without interruption to connected loads. DC battery-derived emergency
power is inverted to AC power and supplied in a pure sine wave output form for 90 minutes
(standard run time). A low voltage battery disconnect circuit prevents “deep discharge”
damage to the batteries during prolonged power outages. When normal power is restored
the system will automatically restart, providing power to connected loads and recharging
the batteries. The charging circuit will bring the batteries to full recharge within UL time
standards.
Construction
The LSN cabinet is constructed of steel, finished with a light gray paint and features
locking cabinetry and password-protected user interface for security. Louvers at front
and top of cabinet allow venting.
ORDERING GUIDE
D 27701
Series
LSN Central
Lighting Inverter
Input Voltage
(VAC)
120(16)
208
240
277
347
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
- N
S 120
B 20 02 U - RSP
Battery Type
Capacity
Rating
01 = 1.0KVA
02 = 2.0KVA
27 = 2.7KVA
37 = 3.7 KVA
48 = 4.8 KVA
55 = 5.5 KVA
66 = 6.6 KVA
83 = 8.3 KVA
10 = 10.0 KVA
12 = 12.5 KVA (1)
15 = 15.0 KVA (1)
17 = 17.5 KVA (2)
S =10-year Sealed
Lead-Calcium
G =20-year Sealed
Lead-Calcium
N =25-year Nickel-
Cadmium
Output Circuit
Breaker Ampere
Rating (7)
Output Circuit
Breaker Type
Blank = Normally On
N = Normally Off
Output
Voltage (3, 4)
(VAC)
120
240
120/208
120/240 (17)
120/277
277
347
Requires a provided external transformer for 208VAC or 240VAC input.
277 and 347VAC input only.
Other voltages available. Consult factory.
External transformer may be provided.
Loading may not exceed 50% of the system’s total rating on any 120VAC leg.
Normally On circuit breakers: a maximum of 14 monitored, single pole positions or
20 unmonitored, single pole positions may be specified. Normally Off circuit breakers: a
maximum of 8 single pole positions (monitored or unmonitored) may be specified.
Normally Off circuit breakers: a maximum rating of 20 amps.
The EPO option requires the SMT option.
Specify runtime in minutes when ordering. Example: AR120.
Available with 1.0, 2.0, 2.7, 3.7, 5.5, and 6.6KVA Series with S batteries only.
Available on 1.0 KVA - 4.8KVA Series.
Available on 5.5 KVA - 17.5KVA Series. Not available with 120V input on 6.6KVA and
above. Not available with 208V input on 12.5 KVA and above. Not available with 240V
input on 15.0 KVA and above.
Supplied in a wall mounted, NEMA 1 type enclosure. Cannot be used in systems with
more than one single-pole output circuit breaker, on systems with different input and
output voltages.
See System Configuration for 90-Minute Run Time.
Type S Battery only; See system configuration for 90-minute run time.
Not available on 8.3KVA - 17.5KVA Series.
Available with 277V input only.
Must be performed within 6 months of inverter shipment to maintain 2 yr full warranty.
Output Circuit Breaker
Supervision
Blank = Monitored
U = Unmonitored
15 3050
20 3560
25 4080
Output Circuit
Breaker Voltage
Rating
A = 120 VAC
B = 240 VAC
C = 277 VAC
D = 208 VAC
Output Circuit
Breaker Quantity (6)
01 to 20
Other Options & Accessories
Options
EML = Email Device
RSP = Remote Status Panel
SMT = System Monitoring
Terminal
EPO = Emergency Power Off
Terminal (8)
AR = Alternate Runtime (9)
SBC = Short Battery Cabinet (10)
IBS = Internal Maintenance
Bypass Switch
(Make Before Break)
C10 = 10 Amp Charger
Upgrade (11)
C20 = 20 Amp Charger
Upgrade (12)
CL60= Cabinet Locks
S
= Seismic Qualified(15)
Accessories
MBB = External Maintenance
Bypass Switch (13)
(Make Before Break)
BBM = External Maintenance
Bypass Switch (13)
(Break Before Make)
DSFK__ =
Seismic Kit (14)
Service Options
FSL
= Factory Start-Up (18)
D Series
D Series
Single-Phase Central Lighting Inverters
Single-Phase Central Lighting Inverters
OPTIONS AND ACCESSORIES
Suffix
EML
SPECIFICATIONS
Options
Description
Email Device
A device that automatically notifies the user of system test results and alarm conditions. The Email Device sends
detailed notifications to up to six pre-programmed email addresses. Requires customer supplied CAT5 cable
connected to user network.
RSP
Remote Status
Panel
Provides remote annunciation for the LSN inverter to indicate inverter and alarm status. Owner-installed option. Must be
installed within 1,000 ft. of the LSN inverter. Seven-conductor-minimum, 22AWG wire for connection from options board to
Remote Status Panel must be supplied by installer.
SMT
System Monitoring
Terminals
Provides connections points for Inverter and Alarm Relays (low power contacts change status with either inverter or alarm
events), and Remote Status Panel (allows the addition of an RSP at any time).
EPO
Emergency Power
Off
Provides a set of terminals to which an Emergency Power Off switch can be wired. Closing the switch will immediately shut down
the system. Note: the EPO option requires the SMT option.
AR
Alternate Runtime
Runtimes other that the standard 90 minutes may be specified. When ordering alternate runtimes, specify discharge time
required in minutes. Example: AR30
SBC
Short Battery
Cabinet
For applications where headroom is limited. Reduces the overall height by 15 inches. Available on systems with ratings
from 1.0, 2.0, 2.7, 3.7, 5.5, and 6.6KVA series with Type S batteries only. Dimensions: 31”H x 30”W x 18 5/8”D.
C10
C20
Charger
Upgrades
10 Amp charger upgrade. Available on 1.0KVA - 4.8KVA Series.
20 Amp charger upgrade. Available on 5.5KVA - 17.5KVA Series.
CL60
Cabinet Locks
Universal cabinet locks for all electronic and battery cabinets.
Monitored
Circuit Breakers
Monitored output circuit breakers (normally-on or normally-off) will sound an alarm when tripped. See Ordering Guide.
Normally-On
Circuit Breakers
Specified when connected loads are to be energized at all times. See Ordering Guide.
Normally-Off
Circuit Breakers
Specified when connected loads are only energized during emergency operation. A user-programmable retransfer delay (up
to 999 seconds) to normal utility power is provided. See Ordering Guide.
Internal
Maintenance
Bypass Switch
A three-position “make before break” service switch mounted inside the cabinet. Compatible with all input/output combinations
and any combination or quantity of output circuit breakers.
Seismic Qualified
Unit provided as a seismic tested and qualified inverter. Unit will continue to operate during and after a seismic event
when installed per instructions. Complies with UBC-1997, IBC-2012, CBC 2013 (OSHPD OSP-0365-10), and
ASCE7-10 S DS=2.0g for z/h=1 and S DS=2.5g for z/h=0,Ip=1.5.
IBS
S
KVA/KW Rating
Accessories
Description
FSL
Factory Start-Up
Start-Up, inspection, test and calibration of system by Dual-Lite factory trained technician.
FEATURES
Warranty
Two years full on all components from date of shipment when a Factory Start-Up is ordered; one year full when a Factory Start-Up is not
ordered. Batteries are covered under a separate warranty:
Battery Type
2.7K
3.7K
4.8K
Power Factor Range
5.5K
6.6K
8.3K
10.0K
12.5K
15.0K
17.5K
.8 lead to .75 lag
Input/Output Voltage
Combinations Available –
Single Phase
Input VAC: 208, 240, 277, 347 (3)
Output VAC: 120, 240, 277, 347, 120/240(1), 120/277
Other voltages available; consult factory(2)
Input VAC: 120, 208, 240, 277, 347
Output VAC: 120, 240, 277, 347, 120/240(1), 120/277
Other voltages available; consult factory(2)
AC Input Circuit Breaker
Rating — 120/277V
120/20A
208/15A
240/15A
277/15A
347/15A
120/30A
208/20A
240/15A
277/15A
347/15A
Output Voltage and
Maximum Output
Current in Amperes
120/8.3
240/4.2
277/3.6
347/2.9
120/16.7 120/22.5 120/30.8 120/40.0
240/8.3 240/11.3 240/15.4 240/20.0
277/7.2 277/9.7 277/13.4 277/17.3
347/5.8 347/7.8 347/10.7 347/13.8
Standard Charger Size
120/40A 120/50A
208/25A 208/30A
240/20A 240/25A
277/20A 277/25A
347/20A 347/20A
120/70A 120/70A 120/80A
—
—
208/40A 208/40A 208/50A 208/70A 208/80A
240/35A 240/35A 240/45A 240/60A 240/70A
277/30A 277/30A 277/40A 277/50A 277/60A
347/25A 347/25A 347/30A 347/50A 347/50A
120/45.8 120/55.0 120/69.2 120/83.3
240/22.9 240/27.5 240/34.6 240/41.7
277/19.9 277/23.8 277/29.9 277/36.1
347/15.9 347/19.0 347/23.9 347/28.8
5 Amps
—
208/100A
240/80A
277/70A
347/60A
—
208/125A
240/100A
277/90A
347/80A
—
—
—
277/100A
347/80A
120/104.0
240/52.1
277/45.1
347/36.0
120/125
240/62.5
277/54.2
347/43.2
120/146
240/72.9
277/63.2
347/50.4
10 Amps
15 Amps
System DC Voltage
96
96
96
96
96
96
96
144
144
144
144
144
Heat Output (BTU/Hr)
175
350
473
648
840
963
1,155
1,453
1,750
2,188
2,625
3,063
On systems with 120/240VAC output, loading may not exceed 50% of the system’s total KVA rating on any 120V leg. Loading beyond 50% on any
120V leg will cause an unsafe condition and transformer failure will occur. Call our Service Line at 800-848-6439 for alternate load connection
configurations.
(2)
An external transformer will be provided for 12.5K and 15.0K configurations with 208VAC and 240VAC input.
(3)
Input voltage on 17.KVA model limited to 277 and 347VAC only.
Electrical
System Short Circuit Rating: 42K AIC, RMS symmetrical
Surge Voltage Test: Per UL 924
Input Power Connection: Terminal block
Input Circuit Breaker: Sized to system rating
Power Factor: Unity 1.0 (KW = KVA)
Power Consumption: Offline, 98% efficient
Inverter Design: Pulse width modulation via IGBT circuitry
IGBT Frequency Switching Rate: 16K Hz per second
Input Voltage:
(1)
Compliances
UL 924 Listed, Emergency Lighting and Power Equipment
(standard 90 minute run time)
UL & CUL 1778 Listed, Uninterruptible Power Supply Equipment
(alternate run times; types G and N batteries)
ANSI C62.41: ANSI C62.45 (Cat. A & B)
FCC class A
National Electrical Code (NFPA 70)
Life Safety Code (NFPA 101)
NEMA Type 1 Cabinetry
OSHA, state and local codes
Made in U.S.A.
2.0K
(1)
Suffix
Installation
Input power entry point is from the cabinet top. Bottom channels
for lifting straps and wall brackets for anchoring. Servicing is
accessible from cabinet front.
1.0K
Full
Pro-rata
S (sealed lead-calcium)
1 year
9 years
G (sealed lead-calcium)
1 year
14 years
N (wet nickel-cadmium)
1 year
14 years
Batteries must be connected to an energized charging circuit
within 90 days from date of shipment or warranty is void.
Factory Start-Up must be performed within 6 months of inverter shipment to
maintain 2 yr full warranty.
1.0 - 6.6KW/KVA
8.3 - 17.5KW/KVA(1)
120, 208, 240, 277, 347VAC
208, 240, 277, 347
Input voltage on 17.5KVA model limited to 277 and 347VAC only.
Input Voltage Range: Invert, +10%, - 12%; boost, -8%
Input Frequency: 60 Hz, ±3%
Synchronizing Slew Rate: 1 Hz per second, nominal
Transfer Time: "No break" switching; instantaneous
Output Wave Shape: True AC sine wave
Output Frequency: Normal: synchronized to utility;
Inverter: ±0.05, 60 Hz, +0.05 Hz
Output Voltage:
(1)
1.0 - 6.6KW/KVA
8.3 - 17.5KW/KVA
120, 240, 277, 347,
120/240 (1), 120/277
120, 240, 277, 347,
120/240 (1), 120/277
On systems with 120/240VAC output, loading may not exceed 50% of the
system's total KVA rating on any 120V leg. Loading beyond 50% on any
120V leg will cause an unsafe condition and transformer failure will occur.
Call factory for alternate load configurations.
Main Output Overcurrent Protection: Circuit breaker, output fuse
Optional Output Circuit Breakers: Normally-On or Normally-Off,
monitored or unmonitored, per customer requirements.
See "Ordering Guide".
Output Regulation: (static) ±5% (5% to 100% resistive load)
Output Distortion: Less than 5% THD (linear load)
Battery Circuit Breaker: Sized to system rating
Battery Cabinet Short Circuit Breaker Protection: Circuit breaker
and fuses
Overload Rating: 150% momentary; 120% for five minutes, 110% for
10 minutes
Two way communication: DB9/RS232 standard
Overload/Short Circuit Protection: Circuit breakers and fuses
AC Lockout: Prevents battery discharge following installation when
AC power is not present
Output Voltage Regulation: Automatic boost tap circuit maintains
output voltage during utility low voltage "brownout" periods
without switching to battery power
Low Voltage Battery Disconnect: Protects the batteries from
damaging “deep discharge” conditions during prolonged power
outages
Time Delay Retransfer: Supplied with “normally off” optional output
circuit breakers. Holds the unit in emergency mode after
normal AC power is restored, allowing utility power to stabilize
and voltage sensitive lighting to resume normal operation.
Delay time is user programmable.
Test Means: Spectron® self-test/self-diagnostic microprocessor
controlled circuitry; manual programmable testing
Indicators: Visual LED indicators, visual graphic display (2 lines,
40 characters), audible alarm system, RS232 two-way communication. Security: Password protected user interface; locking cabinets
Interior Relative Humidity: 95% non-condensing
Battery/Charging System Specifications
Standard Run Time: 90 minutes per UL 924. Optional run times
available via UL 1778 listing.
Charger: Three-step float, temperature compensated. 5 amp, 10
amp, or 15 amp, depending on system rating.
Bus Voltage: 96VDC or 144VDC (system rating dependent)
Battery Condition Monitoring System: Standard
Recharge Cycle: Within UL requirements
Type: Non-spillable "S" Series standard; optional type G and type
N available. See "Battery" section on following page.
DC Switch: Provides isolation and back-feed protection
Operating Temperature Range: 20°C to 30°C (68°F to 86°F)
D Series
Single-Phase Central Lighting Inverters
System Configurations for 90-Minute Runtime
Type S Battery Maintenance-Free Sealed Lead-Calcium —
­ 10-Year Design Life Expectancy at 25°C (77°F)
Standard LSN system battery; lead calcium grid alloy with electrolyte trapped in absorbent glass mat (AGM) separators. Completely sealed
and requires no addition of water over its life expectancy. Polypropylene case and cover includes UL recognized low pressure safety release
vents. No gassing will occur in normal use.
System Capacity
System
Configuration
Total Weight (lbs.)*
1.0K
2.0K
2.7K
3.7K
4.8K
5.5K
6.6K
8.3K
10.0K
12.5K
15.0K
17.5K
A
A
A
A
A
B(1)
B(1)
B(1)
B(1)
B(1)
C(1)
C(1)
838
1,116
1,122
1,222
1,492
1,926
2,130
2,475
2,829
2,861
4,121
4,393
Seismic Kit
Configuration
DSFKB1(1)
DSFKA1
DSFKB2 (1)
DSFKB3 (1)
DSFKC1 (1)
Type G Battery Maintenance-Free Sealed Lead-Calcium —
­ 20-Year Design Life Expectancy at 27°C (80°F)
Optional LSN system battery; plates are separated by a highly porous glass mat, which functions as the electrolyte retainer. Provides the highest possible oxygen recombination. Completely sealed and requires no addition of water over its life expectancy. ABS flame retardant case
and lid.
System Capacity
System
Configuration
Total Weight (lbs.)*
1.0K
2.0K
2.7K
3.7K
4.8K
5.5K
6.6K
8.3K
10.0K
12.5K
15.0K
17.5K
A
A
A
A
B
B
B
B
B
D
D
D
1,365
1,384
1,390
1,472
1,684
2,062
2,630
2,679
3,589
3,657
4,885
5,491
Type N Battery Wet-Cell Nickel-Calcium —
­ 25-Year Design Life Expectancy at 25°C (77°F)
Optional LSN system battery; pocket plate nickel-cadmium elements in an alkaline electrolyte. Polypropylene containers are standard; each
cell is provided with a flip-top, flame arresting, UL recognized vent cap. Covers provide dead-top isolation. Maintainable "wet-cell" construction, requires the addition of distilled water over its life expectancy.
System Capacity
System
Configuration
Total Weight (lbs.)*
Configuration“A”
Depth 18 5/8"
1.0K
2.0K
2.7K
3.7K
4.8K
5.5K
6.6K
8.3K
10.0K
12.5K
15.0K
17.5K
B
B
B
B
B
C
C
D
D
E
E
1,075
1,486
1,644
1,894
2,232
2,532
2,812
3,481
3,940
4,720
5,505
Consult
Factory
Configuration “C”
Depth 18 5/8"
Configuration “B”
Depth 18 5/8"
92''
Configuration “E”
Depth 18 5/8"
Configuration “D”
Depth 18 5/8"
92''
92''
46''
30''
60''
60''
90''
90''
Consult factory for alternate runtimes and battery cabinet configurations.
External transformer (not illustrated) is provided for 12.5K and 15.0K configurations with 208VAC and 240VAC input.
Transformer cabinet dimensions are 18" W x 28" H x 15" D and weighs 250 lbs.
(1)
Add 12" of space to the width between cabinet stacks for seismic qualified option or DSFK seismic kits.
Dual-Lite • www.dual-lite.com
A Hubbell Lighting, Inc. brand with representatives’ offices in principal cities throughout North America.
Copyright © Hubbell Lighting, Inc., All Rights Reserved • Specifications subject to change without notice. • Printed in U.S.A.
0603405 H 5/15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising