Sharp | ER-A750 | pos terminal model er-a750

pos terminal model er-a750
PROGRAMMING
MANUAL
CODE: 00ZERA750UPME
POS TERMINAL
MODEL
ER-A750
(For "U" version)
CONTENTS
CHAPTER 1. SRV RESET (Program Loop Reset) and switch to SRV mode . . . 1
CHAPTER 2. MASTER RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
CHAPTER 3. READING OF SRV MODE PROGRAM . . . . . . . . . . . . . . . . . . . . . 4
CHAPTER 4. SRV MODE PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
CHAPTER 5. IRC SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
* For setting in PGM1 or PGM2 mode, refer to the Operation Manual.
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
Major keys used in the SRV mode
The following major keys are used in the SRV mode.
FUNCTION
KEY
DESRIPTION
↑
Moves cursor up
COURSOR DOWN
↓
Moves cursor down
COURSOR RIGHT
→
Moves cursor right
COURSOR LEFT
←
Moves cursor left
COURSOR UP
PAGE UP
PAGE DOWN
CLEAR
CANCEL
ENTER
ALL ENTER
PAGE UP
Moves page up
PAGE DOWN
Moves page up
CL
CANCEL
ENTER
CA/AT
TOGGLE SELECT
“.” (DECIMAL POINT)
OPEN SUB MENU
SBTL
Clear numeric entry or error message
Operaation cancel & back to previouse menu.
Data entry
All entry terminate.
Toggles between selections
Open sub menu
SRV. reset
CHAPTER1. SRV RESET (Program
Loop Reset) and
switch to SRV mode
Used to return the machine back to its operation state after a lock up
has occurred.
PROCEDURE
In the ER-A750, the following reset switch (location No.: S2) is used
to switch to the service (SRV) mode and to reset.
1) Turn off the AC switch.
2) Set the reset switch to “OFF” position
3) Turn on the AC switch.
4) Turn to “ON” the reset switch.
5) The SRV mode is displayed as shown below.
DISPLAY:
Reset
switch
1Side(Rear side):"ON" position(Reset state)
3Side(Front side):"OFF" position(Reset cancel)
–1–
5) Enter the password key operation
CHAPTER 2. MASTER RESET
(All Memory Clear)
DISPLAY:
ENTER PASSWORD
There are two possible methods to perform a master reset.
Password input procedure: Press the four corners of the keyboard in the sequence of a, b, c, and
d.
MRS-1 (Master resetting 1)
c
a
b
d
Used to clear all memory contents and return machine back to its
initial settings.
Return keyboard back to default for default kyeboard layout.
PROCEDURE
1) Turn off the AC switch.
2) Set the reset switch to “OFF” position
3) Turn on the AC switch.
4) While holding down MRS-1 key , turn to “ON” the reset switch.
* MRS-1 key : The key located on Left upper corner of the keyboard.
MRS-1 Key
Keyboard layout
6) Master reset is started.
DISPLAY:
MASTER RESET
7) After completion of the master reset, the buzzer sounds three
times and the following SRV mode display is shown.
DISPLAY:
Keyboard layout
–2–
6) Set the fixed keys in the table below. (Start from the zero “0” key,
The keys are displayed sequentially.)
MRS-2 (Master resetting 2)
Used to clear all memory and keyboard contents. This reset returns
all programming back to defaults.
DISPLAY:
ENTER 0
The keyboard must be entered by hand. This reset is used if an
application needs different keyboard layout other than that supplied
by a normal MRS-1.
[Key setup procedure]
PROCEDURE
MRS-2
executed
KEY
Key
position set
0
Free key
Setup
complete
0
1) Turn off the AC switch.
Disable
2) Set the reset switch to “OFF” position
3) Turn on the AC switch.
NOTES:
4) While holding down MRS-2 key , turn to “ON” the reset switch.
*1: When the 0 key is pressed, the key of the key number on
display is disabled.
* MRS-2 key : The key located on Right upper corner of the
keyboard.
*2: Push the key on the position to be assigned. With this, the
key of the key number on display is assigned to that key
position.
MRS-2 Key
*3: When relocating the keyboard, the PGM 1/2 mode use standard key layout.
Key
Key
Key name
No.
No.
Keyboard layout
5) Enter the password key operation
Key name
“00” key
Key
No.
Key name
001
“0” key
011
002
“1” key
013 Decimal point “•” key 023
“ENTER” key
003
“2” key
014
“CL” key
“CA/AT” key
004
“3” key
015
“@/FOR” key
005
“4” key
016
“SBTL” key
006
“5” key
017
“MODE” key
007
“6” key
018
UP “↑” key
DOWN “↓” key
008
“7” key
019
009
“8” key
020
LEFT “←” key
010
“9” key
021
RIGHT “→” key
022 “CANCEL” key
024
7) Master reset is started.
DISPLAY:
DISPLAY:
ENTER PASSWORD
MASTER RESET
Password input procedure: Press the four corners of the keyboard in the sequence of a, b, c, and
d.
c
8) After completion of the master reset, the buzzer sounds three
times and the following SRV mode display is shown.
a
DISPLAY:
b
d
Keyboard layout
–3–
Sample of program reports
CHAPTER 3. READING OF SRV
PROGRAM
1. [1 SYSTEM PRESET]
DISPLAY:
The setting contents of SRV mode can be checked with the display
or printer.
DISPLAY: SRV mode screen
Select “1 READING” and press the ENTER key.
↓
DISPLAY: READING item selection screen
Select the desired item, press the ENTER key.
↓
DISPLAY: OUTPUT lead destination select screen
Select the output destination, press the ENTER key.
↓
The setting content is displayed and printed.
–4–
PRINTER:
Report title
JOB# / Data
–5–
PRINTER:
2. [2 DEVICE ASSIGN]
DISPLAY:
Device name/Termiral No.
/Channel No.
Auto cutter
Printer name
Paper sheet type
Not assigned
3. [3 FREE KEY LAYOUT]
DISPLAY:
–6–
–7–
–8–
PRINTER:
Key No. / Key text
/ Key position code
Not assigned
–9–
4. [4 FILE]
DISPLAY:
– 10 –
– 11 –
PRINTER:
File table No. / No. of records
File table No. / No. of index
records-No. of data records
/ No. of used records
File table No. / No. of records
/ No. of blocks
/ No. of used records
File memory start address
Empty memory start address
Memory end address
– 12 –
5. [5 SSP]
DISPLAY:
– 13 –
1. [1 DEVICE ASSIGN]
CHAPTER 4. SRV MODE
PROGRAMMING
DISPLAY: Setting item select screen
DISPLAY: SRV mode screen
Select [1 DEVICE ASSIGN] and press the ENTER key.
↓
Select “2 SETTING” and press the ENTER key.
DISPLAY: DEVICE ASSIGN screen 1/2
↓
DISPLAY: Setting item selection screen
↓ “PAGE DOWN” key
DISPLAY: DEVICE ASSIGN screen 2/2
↓
Select the desired item and press the ENTER key.
↓
Select the item to be changed and press the ENTER key.
The setting content is described below.
The item setting input screen is displayed.
– 14 –
[1 DEVICE ASSIGN]
DISPLAY: Setting screen
- [1 J PRINTER]
- [2 R PRINTER]
- [3 BILL PRINTER]
- [4 REPORT PRINTER]
- [5 KP#1]
- [6 KP#2]
- [7 KP#3]
- [8 KP#4]
- [9 KP#5]
- [10 KP#6]
- [11 KP#7]
- [12 KP#8]
- [13 KP#9]
DISPLAY TEXT
TERMINAL#
CONTENTS
Terminal number
SELECT ITEM
000 ∼ 254
MRS
000
CHANNEL#
PRINTER NAME
Channel number
Connected printer name
0∼7
EPSON TM-T85
SHARP ER-03/04RP
0
★
AUTO CUTTER
Auto cutter function
PAPER SHEET
Paper sheet type setting
[1 DEVICE ASSIGN]
EPSON TM-300
EPSON TM-T80
RESERVED
No
Yes
ONE SHEET
TWO SHEET
NOTE
Self terminal No.
This means local device.
1-254: Except self terminal No.
This means re-routed device.
Re-routing programming is only valid for printer.
0:
No RS-232 channel is assigned.
000:
When this machine is used as a “report printer” of a bulky
data report such as PLU report, printing will be cut midway
automatically on the side of the ER-03/04RP when the
printing time reaches the time-out (about 30 sec). After that,
however, printing will be resumed automatically to complete
printing of the report.
★
★
- [14 CAT#1]
- [15 CAT#2]
- [16 CAT#3]
- [17 SCALE]
- [18 COIN DISP.]
- [19 ONLINE]
- [20 CVM DATA I/F]
DISPLAY TEXT
CONTENTS
SELECT ITEM
MRS
TERMINAL#
Terminal number
000 ∼ 254
000
NOTE
000:
Self terminal No.
This means local device.
1-254:
Except self terminal No.
This means re-routed device.
Re-routing programming is only valid for printer.
CHANNEL#
Channel number
0∼7
0
– 15 –
0:
No RS-232 channel is assigned.
DISPLAY: SYSTEM PRESET screen 3/3
2. [2 SYSTEM PRESET]
DISPLAY: Setting item select screen
Select the job # to be changed and enter the value.
The content of each jog is described below.
Select “1 SYSTEM PRESET” and press the ENTER key.
↓
[JOB#901] : MRS=0002
DISPLAY: SYSTEM RESET screen 1/3
901-A,B: Not used (Fixed at “00”)
901-C:
1.Rounding system
1.Rounding system
901-D:
901-C
Normal
0
Singapole
8
1.TAB setting
901-D
★
1.TAB setting
0.0
1
0.00
2
0.000
3
★
[JOB#902] : MRS=0000
902-A:
↓ “PAGE DOWN” key
DISPLAY: SYSTEM RESET screen 2/3
1.In-line system
1.In-line system
902-A
No
0
Yes
1
★
902-B,C,D: Not used (Fixed at “000”)
[JOB#903] : MRS=4000
903-A:
903-B:
↓ “PAGE DOWN” key
– 16 –
1.IR (ECR data copy) baud rate
1.IR baud rate
903-A
2400
2
4800
3
9600
4
19200
5
38400
6
57600
7
115200
8
★
1.Symbol of scale entry
1.Symbol of scale entry
903-B
“LB”
0
“KG”
2
★
903-C:
1.Scale entry system
[JOB#906] : MRS=0031
2.Entry of tare
906-A:
3.Unit of weight for the scale
1.Scale entry
system
2.Entry of tare
Disallowed
Manual
Allowed
Disallowed
Automatic
Allowed
903-D:
1.Printing of Dept. and PLU code
2.Entry which makes the PLU stock counter negative
3.Unit of weight
for the scale
903-C
2id(3id)+2dd
0
1id(2id)+3dd
1
2id(3id)+2dd
2
1id(2id)+3dd
3
Inhibited
2
2id(3id)+2dd
4
Allowed unconditionally
4
1id(2id)+3dd
5
5
2id(3id)+2dd
6
Operation allowed despite
error message
1id(2id)+3dd
7
Inhibited
6
1.Printing of Dept.
and PLU code
★
No
Yes
906-B:
Not used (Fixed at “0”)
2.Entry which makes the PLU
stock counter negative
906-A
Allowed unconditionally
0
Operation allowed despite
error message
1
1.Hash department setting
1.Hash department setting
906-B
[JOB#904] : MRS=0000
Enable
0
904-A:
Disable
2
904-B:
1.Printing of date
1.Printing of date
904-A
Yes
0
No
4
906-C:
★
Yes
No
1.Split pricing counting
1.Split pricing
counting
904-B
0
★
4
906-D:
1.Taxable 4 subtotal print on X/Z report
Disable
905-A
Print
Skip
Print
Skip
Skip
Split pricing
6
Ffx (FF sequence + Split pricing)
7
2.Fractional quantity
★
No
0
1
No
2
Yes (3 digit decimal place)
3
0
1
Print
2
Skip
3
[JOB#907] : MRS=0010
Print
4
907-A,B: Not used (Fixed at “00”)
907-C:
Enable
5
6
1.Minus Dept./PLU
907-C
Skip
7
Disable
0
Enable
1
907-D:
905-B
Print
0
Skip
1
Print
4
Skip
5
★
905-C, D: Not used (Fixed at “00”)
– 17 –
★
1.Minus Dept./PLU
Skip
Print
2.Tax printing when
tax is zero.
★
906-D
Yes (3 digit decimal place)
Skip
2.Tax printing when tax is zero.
Print
4
Print
1.Tax printing when taxable subtotal is zero.
Skip
3
Multiplication
3.Net Tax 4 total
Print
1.Tax printing when
taxable subtotal is zero.
2
Ffx (FF sequence + Split pricing)
1.Presetting of consective No.
1.Presetting of
consective No.
3.Net Tax 4 total print on X/Z report
905-B:
0
Split pricing
2.Fractional quantity
2.Gross Tax 4 and refund Tax 4 total print on X/Z report
2.Gross Tax 4
and refund
Tax 4 total
906-C
Multiplication
Package
[JOB#905] : MRS=0005
1.Taxable 4
subtotal
2.Multiplication entry
Quantity
904-C,D: Not used (Fixed at “00”)
905-A:
★
2.Multiplication entry
1.Printing of the consecutive No.
1.Printing of the consecutive No.
★
Not used (Fixed at “0”)
★
909-B:
[JOB#908] : MRS=0000
908-A:
GT print on Z report
GT1 (NET)
GT2 (+)
GT3 (–)
908-A
Print
0
Print
Skip
Print
Skip
Print
2
Skip
3
Print
4
Skip
5
Print
6
Skip
7
Skip
Skip
908-B:
GT2 (+)
2. Printing of VOID mode totalizer and MGR VOID totalizer
on Z1 report
1.Printing of VOID
mode totalizer and
MGR VOID totalizer
on Z2 report
0
Skip
2
Print
4
Skip
6
Skip
2
Print
3
Skip
4
[JOB#910] : MRS=0024
Print
5
910-A:
Skip
6
1. Drawer open at server sign ON/OFF
910-A
Print
7
No
0
Yes
2
★
Skip
909-D:
2.Resetting of consective number in Z1 resetting
2.Resetting of
consective number in
Z1 resetting
No
Yes
Print
1
1.Add void -mode transaction data to hourly total report
No
908-C
0
Print
0
Yes
1
No
4
Yes
5
1. Drawer open at server sign ON/OFF
Not used (Fixed at ”0”)
910-C:
1.Server # entry system
★
910-D:
2.Server # entry system
910-C
Stay down
0
Auto sign off
2
1.Printing of X/Z report 2.Z1 resetting that resets GT
911-A:
Disable
908-D
0
Enable
1
Disable
4
Enable
5
★
911-D:
Not used (Fixed at “4”)
1. Fraction treatment
1. Fraction treatment
911-A
Round off
0
Round up
1
Round down
2
1.RECEIPT/SLIP header format
911-D
Format 1
0
2.Printing of training GT on the Z report
Format 2
2
Format 3
4
2.Printing of training GT on
the Z report
909-A
Print
0
Skip
1
Print
2
Skip
3
★
1.RECEIPT/SLIP header format
1.Printing of training GT on the X report
Print
★
911-B, C: Not used (Fixed at “00”)
[JOB#909] : MRS=2000
Skip
★
[JOB#911] : MRS=0000
1.Printing of X/Z report
1.Printing of training
GT on the X report
★
Not used (Fixed at “0”)
910-B:
908-C
2.Z1 resetting that resets GT
909-A:
2.Printing of VOID mode
totalizer and MGR VOID
totalizer on Z1 report
Print
Print
Journal only
4
908-B
Skip
Receipt & Journal
Skip
★
1. Printing of VOID mode totalizer and MGR VOID totalizer
on Z2 report
Skip
Print
908-D:
0
GT3 (–)
Skip
1.Add void -mode
transaction data to
hourly total report
909-B
Print
Print
Skip
908-C:
909-C:
GT print on X report
GT1 (NET)
1.Printing of data on PLU resetting report
★
1
Print
1.Printing of data on PLU resetting report
★
– 18 –
★
Format 1:
Normal
(Logo message format)
0
← Date / Machine No.
üé⁄ üå⁄ èç
123456
#0123
12:34
jack____0001
1
2
3
5
← CC-No. / Time / Cashier name /
Cashier Code
Format 2:
Normal
← Date / Machine No.
üé⁄ üå⁄ èç
123456
ìüéâä 12:34
jack____0001
[JOB#913] : MRS=0104
← CC-No. / Time / Cashier name /
Cashier Code
913-A:
Not used (Fixed at “0”)
913-B:
1.Printing of SBTL
Format 3:
Normal
2.Printing of MDSE SBTL
3.Escape the compulsory of bill
üé⁄ üå⁄ èå
123456
← Date / Machine No.
ìüéâä 12:34
____üüüé
← CC-No. / Time / Cashier Code
1.Printing of
SBTL
2.Printing of
3.Escape the
MDSE SBTL
compulsory of bill
No
No
[JOB#912] : MRS=0061
912-A:
912-B:
Yes
1. Data print format
1. Data print format
912-A
Month / Day / Year
0
Day / Month / Year
1
Year / Month / Day
2
No
Yes
★
Yes
913-C:
1.Time system
912-B
12 H
0
24 H
1
1.Lock error buzzer
keeps sounding
★
2.Copy receipt function
2.Copy
receipt
function
Total only
Yes
No
Detail
Yes
912-D:
1
Disable
2
Enable
3
Disable
4
Enable
5
Disable
6
Enable
7
2.Buffered keyboard
Constant
3.Footrer print control
No
0
Enable
★
2.Buffered keyboard
1.Time system
1.After transaction receipt
1.After
transaction
receipt
Disable
1.Lock error buzzer keeps sounding
2 sec. off
912-C:
913-B
913-D:
3.Footrer print control
912-C
913-C
Yes
0
No
1
Yes
2
No
3
★
1.Drawer closing compulsory
2.Error system
3.Key touch sound
All receipts
0
On selected function key
at the time of finalization
1
All receipts
2
On selected function key
at the time of finalization
3
All receipts
4
On selected function key
at the time of finalization
5
All receipts
6
On selected function key
at the time of finalization
1.Drawer closing
compulsory
All lock error
Non-compulsory
Miss operation
(One shot error)
All lock error
Compulsory
★
Miss operation
(One shot error)
7
1.Logo message control
1.Logo message control
2.Error system
912-D
3-line header insted of a logo
0
Logo only
1
Logo and 3-line footer
2
6-line header insted of a logo
3
3-line header insted of a logo and 3-line footer
5
★
– 19 –
3.Key touch
sound
913-D
Yes
0
No
1
Yes
2
No
3
Yes
4
No
5
Yes
6
No
7
★
[JOB#914] : MRS=1100
[JOB#915] : MRS=0040
914-A:
915-A:
1. Recipt issuing at no-sale
1.Amount symbol
2. No-sale key separation from CA/AT key for no-sale function
1.Amount symbol
915-A
“$”
0
3. Tax delete
1.Recipt
2.No-sale key separation
issuing
from CA/AT key for noat no-sale
sale function
3.Tax
delete
Yes
Yes
No
Yes
No
No
914-B:
914-A
915-B:
“*”
1
“(Space)”
2
1.PO system
915-B
Mixed entry
0
Cash only entry
1
1.PO system
Inhibit
0
Enable
1
Inhibit
2
Enable
3
Inhibit
4
Enable
5
2. No. of times of ST(–) or ST(%) entry within one transaction
Inhibit
6
3. RA system
Enable
7
★
915-C:
1.Paper
near end
check
1.No-sale after non-add code entry
1.No-sale after non-add code entry
914-B
Disable
0
Enable
1
2.No. of times of
ST(–) or ST(%)
entry within one
transaction
Any No. of times
★
1. Action to be taken when the machine is locked by the
Receipt/Journal paper near end check
Only once
2. VOID mode
Any No. of times
3. Non-add code entry at the begining of a transaction operation
No
Only once
1.Action to be taken
2.VOID
when the machine is
mode
locked by the
Receipt/Journal
paper near end check
Enable
Un locked by CL key
Disable
Enforcing of paper roll
replacement
Enable
Disable
914-D:
3.Non-add code
entry at the
begining of a
transaction
operation
914-C
Non-compulsory
0
Compulsory
1
Non-compulsory
2
Compulsory
3
Non-compulsory
4
Compulsory
5
Non-compulsory
6
Compulsory
915-D:
★
916-A:
Enable
Enable
Disable
Disable
Enable
Mixed entry
0
Cash only entry
1
Mixed entry
2
Cash only entry
3
Mixed entry
4
Cash only entry
5
Mixed entry
6
Cash only entry
7
★
1. Action to be taken when text and amount overlaps each
other in a REG mode entry
1.Action to be taken when text and
amount overlaps each other in a REG
mode entry
916-B:
7
916-C:
914-D
Enable
0
Disable
1
Enable
2
Disable
3
Enable
4
Disable
5
Enable
6
Disable
7
916-A
Truncate text
0
2-line print
1
★
1.Finalization by charge when ST t 0
1.Finalization by charge when ST t 0
916-B
Inhibit
0
Always
4
3.Non-add code entry
Disable
915-C
[JOB#916] : MRS=1400
2.Check/Cashing
2.Check/Cashing 3.Non-add
code entry
3.RA system
Not used (Fixed at “0”)
1.Manual TAX
1.Manual TAX
★
1. Paper near end check
Yes
914-C:
★
★
1.Negative merchandise subtotal
2.Subtotal entry before tender
★
3.Subtotal entry before direct non-tendering finalization
1.Negative
merchandise
subtotal
2.Subtotal entry
before tender
Non-compulsory
Enable
Compulsory
Non-compulsory
Disable
Compulsory
– 20 –
3.Subtotal entry
before direct
non-tendering
finalization
916-C
Non-compulsory
0
Compulsory
1
Non-compulsory
2
Compulsory
3
Non-compulsory
4
Compulsory
5
Non-compulsory
6
Compulsory
7
★
916-D:
1.Coupon PLU printing on X/Z report
917-D:
1. Printing of Total Tax on X/Z report
2.Net sales subtotal(NET1) printing on X/Z report
2. Printing of Gross manual Tax and Refund manual Tax on
X/Z report
3.Check change total printing on X/Z report
1.Coupon PLU
2.Net sales
subtotal(NET1)
Print
Print
Skip
Print
Skip
Skip
3. Printing of Net manual Tax total on X/Z report
3.Check
change total
916-D
Print
0
Skip
1
Print
2
Skip
3
Print
4
Skip
5
Print
6
Skip
7
1.Total
Tax
★
2.Gross manual Tax and
Refund manual Tax
3.Net manual
Tax total
917-D
Print
0
Skip
1
Print
Print
Skip
Print
Print
2
Skip
3
Print
4
Skip
5
Skip
Skip
Print
6
Skip
7
★
[JOB#917] : MRS=0000
917-A:
[JOB#918] : MRS=2233
1. Printing of Taxable 1 subtotal on X/Z report
918-A:
2. Printing of Gross Tax 1 and Refund Tax 1 totals on X/Z
report
1. Printing of text of a tied PLU in set PLU
2. Direct non-tendering finalization after previous tender
entry
3. Printing of Net Tax 1 total on X/Z report
1.Taxable 1
subtotal
2.Gross Tax 1 and
Refund Tax 1 totals
Print
Print
Skip
Print
Skip
Skip
917-B:
3.Net Tax 1
total
3. Output of set PLU to KP
917-A
Print
0
Skip
1
Print
2
Skip
3
Print
4
Skip
5
Print
6
Skip
7
1.Printing of 2.Direct non-tendering 3.Output of
text of a
finalization after
set PLU to
tied PLU in
previous tender entry KP
set PLU
★
Disable
Print
Enable
Disable
Skip
1. Printing of Taxable 2 subtotal on X/Z report
Enable
2. Printing of Gross Tax 2 and Refund Tax 2 totals on X/Z
report
918-B:
3. Printing of Net Tax 2 total on X/Z report
1.Taxable 2
subtotal
2.Gross Tax 2 and
Refund Tax 2 totals
Print
Print
Skip
Print
Skip
Skip
917-C:
3.Net Tax 2
total
Print
917-B
0
Skip
1
Print
2
Skip
3
Print
4
Skip
5
Print
6
Skip
7
★
No
Yes
918-C:
Print
Print
Skip
Print
Skip
Skip
Print
1
By tied PLU
2
Set PLU’s KP
3
By tied PLU
4
Set PLU’s KP
5
By tied PLU
6
Set PLU’s KP
7
★
1.Kitchen printer
recapitulation
917-C
Skip
1
Print
2
Skip
3
Print
4
Skip
5
Print
6
Skip
7
Enable
918-B
0
Disable
1
Enable
2
Disable
3
★
1. Kitchen printer recapitulation
Yes
0
2.Fractional entries for
non-scalable
UPC/PLU/DEPT.
2. Printing the DEPT./PLU text on KP in double size character
3. Printing of Net Tax 3 total on X/Z report
3.Net Tax 3
total
0
1.Red color printing on KP when PLU’s unit price is zero
1.Red color printing on
KP when PLU’s unit
price is zero
1. Printing of Taxable 3 subtotal on X/Z report
2.Gross Tax 3 and
Refund Tax 3 totals
By tied PLU
Set PLU’s KP
2.Fractional entries for non-scalable UPC/PLU/DEPT.
2. Printing of Gross Tax 3 and Refund Tax 3 totals on X/Z
report
1.Taxable 3
subtotal
918-A
No
★
– 21 –
2.Printing the DEPT./PLU text
on KP in double size character
918-C
Print
0
Skip
1
Print
2
Skip
3
★
918-D:
1.Tip paid includes cash tip
2.Clearing of tip totalizer at server Z1 report
[JOB#920] : MRS=2000 : INLINE PROGRAMMING
AREA
3.Printing of tip totalizer on the server report
920-A:
1.Tip paid
includes
cash tip
2.Clearing of tip
3.Printing of tip
totalizer at
totalizer on the
server Z1 report
server report
No
Yes
Yes
No
No
Yes
1.Back-up master function
Not
Exist
918-D
No
0
Yes
1
No
2
Yes
3
920-B:
No
4
Disable
0
5
Enable
4
No
6
Yes
7
920-C:
2.PGM-mode programming at the satellite
2
Compulsory
3
Non-compulsory
4
Compulsory
5
Guest Look-Up system
919-B:
Nothing
Non-compulsory
PB Look-Up system
2.PGM-mode programming
at the satellite
Exist
2. GLU/PBLU code entry at reorder (When #919:B-1 is 0 “
Auto generation ”)
919-A
★
1.Broadcast communication
1.Broadcast
communication
2.GLU/PBLU code entry
at reorder
★
920-B
Yes
1. GLU/PBLU system
1.GLU/PBLU system
920-A
0
1
1. System report and down-load job is executed in the
back-up master
1.System report and down-load job is executed in
the back-up maste
★
[JOB#919] : MRS=5000
919-A:
1.Back-up master function
920-D:
920-C
Disable
0
Enable
1
Disable
4
Enable
5
★
1.The register is
1.The register is
920-D
Standard alone machine
0
Satellite
1
Master
2
Back up master
3
★
1. Checking of server# on guest check when a reorder is
made
★
2. Guest check No.
1.Checking of server# on guest
check when a reorder is made
Yes
No
919-C:
2.Guest check
No.
[JOB#921] : MRS=0000
919-B
★
921-A:
Not used (Fixed at “0”)
921-B:
1.GLU system
Auto genertion
0
Manual
1
2.Drive thru system
Auto genertion
4
3.Drive thru entry
Manual
5
1.GLU system
1.PB entry
2.Amount printing when PLU unit price is 0
1.PB entry
2.Amount printing when
PLU unit price is 0
Non-compulsory
Compulsory
919-D:
Centralized
Centralized
919-C
No
0
Yes
1
No
2
Yes
2.Drive thru
system
Individual
★
Centralized
Individual
3
Individual
1.Conversion SBTL printing of native SBTL
921-C,D: Not used (Fixed at “00”)
2.Foreign currency format
1.Conversion SBTL
printing of native SBTL
2.Foreign currency
format
919-D
Not
0
Yes
Omit digits lower than
tab position
1
Not
4
No
Omit digits lower than
tab position
5
★
– 22 –
3.Drive thru entry
921-B
Non-compulsory
0
Compulsory
1
Non-compulsory
2
Compulsory
3
Non-compulsory
4
Compulsory
5
Non-compulsory
6
Compulsory
7
★
925-C:
[JOB#922] : MRS=0008 : INLINE PROGRAMMING
AREA
1.Report printing when consolidation daily and
periodic total transaction reading or resetting is
taken
922-A,B: Not used (Fixed at “00”)
922-C,D: 1. Programming of the SRN transmission speed and carrier-off waiting time
Transmission speed
1. Report printing when consolidation daily and periodic
total transaction reading or resetting is taken
Carier-off waiting time
922-CD
Printing of both i.e. reports on individual machines
and consolidation report on the entire system
3.2 msec
01
Printing of consolidation report on the entire system
1
6.4 msec
02
Printing of report on individual register
2
480 kbps
1 Mbps
9.6 msec
04
12.8 msec
00
1.6 msec
09
3.2 msec
10
4.8 msec
12
6.4 msec
08
925-D:
1.Resetting is allowed when the
server is remained sign on
No
★
Yes
0000 ∼ 9900
00-99
923-D:
923-C
No
0
Yes
1
1.Sending “LAST VOID
DATA” on KP
0 ∼ 9 Sec.
0∼9
No
★
926-C:
1
Yes
2
No
3
★
926-B
2
★
1.Open store / Close store : standalone ECR with on-line
2.Send AT
command
string with
JOB#500
No
924-A
Yes
0
No
1
Yes
2
No
3
Yes
No
Yes
★
[JOB#925] : MRS=0303 : INLINE PROGRAMMING
AREA
1.Various individual resetting
0
No
0
Yes
925-B:
Yes
No
No
2. Locking after
Transaction resetting
Not used (Fixed at “0”)
★
926-A
Yes
2. Locking after Transaction resetting
925-A:
3
1.Sending “REFUND DATA” on KP
1.Open store /
Close store :
standalone ECR
with on-line
1. Locking after Daily Net resetting
No
2
Enable
3.Send AT command string with JOB#501
Programming whether or not to lock REG-mode entries
after individual periodic total resetting when the system has
no save file,
Yes
1
2.Send AT command string with JOB#500
924-A,B,C: Not used (Fixed at “143”)
1. Locking after Daily
Net resetting
Enable
Disable
1.Sending “REFUND DATA” on KP
[JOB#924] : MRS=1433 : INLINE PROGRAMMING
AREA
924-D:
0
2.Sending “PAST VOID
DATA” on KP
Yes
926-B:
923-D
Disable
2.Sending “PAST VOID DATA” on KP
1.Polling cycle (second)
1.Polling cycle (second)
925-D
1.Sending “LAST VOID DATA” on KP
1.T-log Function
1.T-log Function
2.Resetting in the
open store state
[JOB#926] : MRS=0000
926-A:
923-AB
★
2.Resetting in the open store state
923-A,B: 1.The record number for REQUEST of T-LOG POLLING
(x100)
1.The record number for REQUEST of T-LOG
POLLING (x100)
0
1.Resetting is allowed when the server is remained sign on
[JOB#923] : MRS=0010 : INLINE PROGRAMMING
AREA
923-C:
925-C
1.Various individual resetting
925-B
Disable
2
Enable
3
926-D:
★
– 23 –
3.Send AT
command
string with
JOB#501
926-C
No
0
Yes
1
No
2
Yes
3
No
4
Yes
5
No
6
Yes
7
★
1.Reverse On-line channel in close store
1.Reverse On-line channel in close store
926-D
No
0
Yes
4
★
[JOB#927] : NOT US ED MRS=0000
[Z REPORT COUNTER]
[JOB#928] : MRS=0060
DISPLAY: Setting item select screen
928-A,B: Not used (Fixed at “00”)
928-C:
1.Printing of PLU on bill when it is 0
2.Printing of text of a tied PLU in set PLU on bill
1.Printing of PLU
on bill when it is 0
2.Printing of text of a tied
PLU in set PLU on bill
928-C
Yes
0
No
2
Yes
4
No
6
Yes
No
928-D:
★
1.Compulsory bill print system
1.Compulsory bill print system
928-D
According to each media’spreset
(The bill printing at service and final in GLU system
actes on each mwdia’s)
0
Compulsory every entry
1
Compulsory for PB entry
2
★
Select “3 Z REPORT COUNTER” and press the ENTER
key.
↓
[JOB#929] : MRS=0100
929-A:
1.KP print format when finalizing
929-A
Simple
0
Detail
1
929-B:
Not used (Fixed at “1”)
929-C:
1.When closed file is full
929-D:
DISPLAY: Z REPORT COUNTER screen 1/2
1.KP print format when finalizing
1.When closed file is full
929-C
Inhibited
0
Registration is continued
1
★
★
Not used (Fixed at “0”)
[JOB#981] : MRS=0000
981-A:
1.Tax amount display on screen
1.Tax amount display on screen
981-A
No
0
Yes
4
★
↓ “PAGE DOWN” key
DISPLAY: Z REPORT COUNTER screen 2/2
981-B,C,D: Not used (Fixed at “000”)
Select the report to be changed and enter the value.
The contents of displayed reports are as listed in the table below.
– 24 –
DISPLAY TEXT
TRANSACTION Z1
CONSOLI.TRAN. Z1
SERVER Z1/Z2
HOURLY Z1
PLU Z1/Z2
GLU Z1
DRIVE THRU Z1
TRANSACTION Z2
CONSOLI.TRAN. Z2
DAILY NET Z2
DEPARTMENT Z1
DEPARTMENT Z2
CONTENTS
Transaction Z1 report counter
Consolidation transaction Z1
report counter
Server Z1/Z2 report counter
Hourly Z1 report counter
PLU Z1/Z2 report counter
GLU / PBLU Z1 report counter
Drive thru Z1 report counter
Transaction Z2 report counter
Consolidation transaction Z2
report counter
Daily net Z2 report counter
Department Z1 report counter
Department Z2 report counter
[PGM2MODE SECRET#]
MRS
0000
DISPLAY: Setting item select screen
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
[GT]
DISPLAY: Setting item select screen
Select “5 PGM2 MODE SECRET#” and press the ENTER
key.
↓
DISPLAY: PGM2 MODE SECRET # screen
Select “4 GT” and press the ENTER key.
↓
DISPLAY: GT screen
Enter the value.
The content of displayed SECRET# is as shown below.
DISPLAY TEXT
SECRET#
Select the report to be changed and enter the value.
The contents of displayed GT are listed in the table below.
DISPLAY TEXT
POSITIVE GT
NEGATIVE GT
TRAINING GT
CONTENTS
GT2 (Positive GT) : Max.13 digits
GT3 (Negative GT) : Max.13 digits
TRAINING GT: Max.13 digits
MRS
0.00
0.00
0.00
GT1 is obtained by the following equation.
EQUATION: GT1 = GT2 ∼ GT3
– 25 –
CONTENTS
PGM2 mode secret code (4digits)
MRS
0000
<Key No. Table>
[FREE KEY LAYOUT]
Key
No.
DISPLAY: Setting item select screen
Key text
Position code
(MRS)
001 0 KEY
0 KEY
109
002 1 KEY
1 KEY
110
003 2 KEY
2 KEY
122
004 3 KEY
3 KEY
134
005 4 KEY
4 KEY
111
006 5 KEY
5 KEY
123
007 6 KEY
6 KEY
135
008 7 KEY
7 KEY
112
009 8 KEY
8 KEY
124
010 9 KEY
9 KEY
136
011 00 KEY
00 KEY
121
012 000 KEY
000 KEY
—
Function name
013 DECIMAL POINT KEY
Select “6 FREE KEY LAYOUT” and press the ENTER
key.
↓
. KEY
133
014 CLEAR KEY
CL KEY
137
015 @/FOR KEY
@/FOR
125
016 SUB TOTAL KEY
SBTL
146
017 MODE KEY
MODE
155
UP
086
019 CURSOL DOWN (↓) KEY
DOWN
085
020 CURSOL LEFT (←) KEY
LEFT
073
018 CURSOR UP (↑) KEY
DISPLAY: FREE KEY LAYOUT screen 1/2
021 CURSOL RIGHT (→) KEY
RIGHT
097
CANCEL
099
023 ENTER KEY
ENTER
098
024 CA/AT KEY
CA/AT
145
025 PAGE UP KEY
P UP
101
026 PAGE DOWN KEY
P DOWN
100
027 BACK SPACE KEY
BKSPC
—
DEL
—
022 CANCEL KEY
028 DELETE KEY
029 MERCHANDISE SUB TOTAL KEY
MDS ST
115
030 TRAY SUB TOTAL KEY
TRY ST
150
031 NON-ADD CODE KEY
032 NO SALE KEY
↓ To shift the screen, use the cursor key, or enter the key No.
and press the ENTER key.
Since key No. 1 ∼ 24 are fixed,
the initial screen starts from key
No. 25.
When forming keys: Select the key to be formed with the cursor and
press the key to be formed.
With the cursor key,
the key No. is retrieved and
specified.
Retrieve and specification by
directly entering the key No.
XXX
With " " key and " "key,
the screen is selected and the
key No. specified
ENTER
Key No.
With the above operation, the
screen is selected and the key No.
– 26 –
—
—
033 SCALE KEY
SCALE
—
034 PLU / SUB DEPT. KEY
PLU/SB
138
035 LEVEL 1 KEY
L1
096
036 LEVEL 2 KEY
L2
108
037 LEVEL 3 KEY
L3
120
038 LEVEL 4 KEY
L4
132
039 LEVEL 5 KEY
L5
144
040 PRICE 1 KEY
P1
—
041 PRICE 2 KEY
P2
—
042 PRICE 3 KEY
P3
—
043 PRICE 4 KEY
P4
—
044 PRICE 5 KEY
P5
—
045 TAX 1 SHIFT KEY
TAX1SF
119
046 TAX 2 SHIFT KEY
TAX2SF
131
047 TAX 3 SHIFT KEY
TAX3SF
—
048 TAX 4 SHIFT KEY
TAX4SF
—
049 BILL KEY
Press the key to be formed
#
NS
BILL
—
050 COPY/AFTER TRANS. RECEIPT
KEY
RCPT
117
051 NON CASH CHIP KEY
CH TIP
—
052 CASH TIP KEY
CA TIP
—
053 TIP PAID KEY
TIP PD
—
054 LAST VOID KEY
VOID
—
055 INDIRECT VOID KEY
I.VOID
114
Key
No.
Key text
Position code
(MRS)
Key text
Position code
(MRS)
056 SUB TOTAL VOID KEY
ST VD
126
057 REFUND KEY
RFND
141
112 CHARGE 4 KEY
CH4
—
113 CHARGE 5 KEY
CH5
058 RETURN KEY
RETURN
—
140
114 CHARGE 6 KEY
CH6
059 %1 KEY
—
%1
128
115 CHARGE 7 KEY
CH7
—
060 %2 KEY
%2
—
116 CHARGE 8 KEY
CH8
—
061 %3 KEY
%3
—
117 CURRENCY CONVERSION 1 KEY
CONV1
—
062 %4 KEY
%4
—
118 CURRENCY CONVERSION 2 KEY
CONV2
—
063 %5 KEY
%5
—
119 CURRENCY CONVERSION 3 KEY
CONV3
—
064 %6 KEY
%6
—
120 CURRENCY CONVERSION 4 KEY
CONV4
—
065 %7 KEY
%7
—
121 GLU / PBLU KEY
PBAL
—
066 %8 KEY
%8
—
122 DRIVE THRU (RE ORDER) KEY
PBAL2
153
067 %9 KEY
%9
—
123 NEW CHECK KEY
N.C.
—
068 (–)1 KEY
(–)1
116
124 DRIVE THRU (NEW CHECK) KEY
N.C.2
154
069 (–)2 KEY
(–)2
—
125 SERVICE KEY
SRVC
152
070 (–)3 KEY
(–)3
—
126 FINAL KEY
FINAL
151
071 (–)4 KEY
(–)4
—
127 DEPOSIT KEY
DEPO
—
072 (–)5 KEY
(–)5
—
128 DEPOSIT REFUND KEY
DEP.RF
—
073 (–)6 KEY
(–)6
—
129 BILL TRANSFER KEY
B.T.
—
074 (–)7 KEY
(–)7
—
130 RECEIVED ON ACCOUNT KEY
RA
—
075 (–)8 KEY
(–)8
—
131 RECEIVED ON ACCOUNT 2 KEY
RA2
—
076 (–)9 KEY
(–)9
—
132 PAID OUT KEY
PO
—
077 TAX KEY
TAX
—
133 PAID OUT 2 KEY
PO2
—
CV CNT
—
134 SERVER NUMBER KEY
SRV#
113
Function name
078 COVER COUNT KEY
Key
No.
Function name
079 AUTO KEY
AUTO
143
135 MANEGER NUMBER KEY
MGR#
—
080 AUTO 2 KEY
AUTO2
142
136 EMPLOYEE NUMBER KEY
EMPL#
130
081 AUTO 3 KEY
AUTO3
—
137 EAT IN 1 KEY
EATIN1
—
082 AUTO 4 KEY
AUTO4
—
138 EAT IN 2 KEY
EATIN2
—
083 AUTO 5 KEY
AUTO5
—
139 EAT IN 3 KEY
EATIN3
—
084 AUTO 6 KEY
AUTO6
—
140 REMOTE PRINTER SEND KEY
RP SND
118
085 AUTO 7 KEY
AUTO7
—
141 GRATUITY EXEMPT KEY
GRT EX
—
086 AUTO 8 KEY
AUTO8
149
142 OPEN TARE KEY
OPN TR
—
087 AUTO 9 KEY
AUTO9
148
143 BALANCE KEY
BAL
129
088 AUTO 10 KEY
AUTO10
147
144 REPEAT KEY
REPEAT
—
089 AUTO 11 KEY
AUTO11
—
145 TRANSACTION OUT KEY
TR.OUT
—
090 AUTO 12 KEY
AUTO12
—
146 TRANSACTION IN KEY
TR.IN
—
091 AUTO 13 KEY
AUTO13
—
147 PERSON NUMBER KEY
PERSN#
—
092 AUTO 14 KEY
AUTO14
—
148 INDIVIDUAL PAYMENT KEY
093 AUTO 15 KEY
AUTO15
—
094 AUTO 16 KEY
AUTO16
095 AUTO 17 KEY
096 AUTO 18 KEY
I.PAY
—
149 EMPLOYEE SALES KEY
E.SALE
—
—
150 MISC MENU KEY
M.FUNC
156
AUTO17
—
151 CHECK MENU KEY
CHK.MN
127
AUTO18
—
152 CHARGE MENU KEY
CHG.MN
139
097 AUTO 19 KEY
AUTO19
—
153 CONVERSION MENU KEY
CNV.MN
—
098 AUTO 20 KEY
AUTO20
—
154 RECEIPT ON/OFF KEY
RCP.SW
—
099 AUTO 21 KEY
AUTO21
—
999 INHIBIT
—
—
100 AUTO 22 KEY
AUTO22
—
101 AUTO 23 KEY
AUTO23
—
102 AUTO 24 KEY
AUTO24
—
103 AUTO 25 KEY
AUTO25
—
104 CASH 2 KEY
CA2
—
105 CHECK KEY
CHK
—
106 CHECK 2 KEY
CHK2
—
107 CHECK 3 KEY
CHK3
—
108 CHECK 4 KEY
CHK4
—
109 CHARGE 1 KEY
CH1
—
110 CHARGE 2 KEY
CH2
—
111 CHARGE 3 KEY
CH3
—
– 27 –
KEY POSITION CODE
12
24
36
48
[FILE]
60
72
84
DISPLAY: Setting item select screen
96 108 120 132 144 156
11
23
35
47
59
71
83
95 107 119 131 143 155
10
22
34
46
58
70
82
94 106 118 130 142 154
9
21
33
45
57
69
81
93 105 117 129 141 153
8
20
32
44
56
68
80
92 104 116 128 140 152
7
19
31
43
55
67
79
91 103 115 127 139 151
6
18
30
42
54
66
78
90 102 114 126 138 150
5
17
29
41
53
65
77
89 101 113 125 137 149
4
16
28
40
52
64
76
88 100 112 124 136 148
3
15
27
39
51
63
75
87
99 111 123 135 147
2
14
26
38
50
62
74
86
98 110 122 134 146
1
13
25
37
49
61
73
85
97 109 121 133 145
Select “8 FILE” and press the ENTER key.
[INIT. KEY LAYOUT]
↓
DISPLAY: FILE screen 1/5
The keyboard layout is reset to the standard layout.
DISPLAY: Setting item select screen
↓ Screen is selected with the
“PAGE DOWN” key and the cursor key.
Select “7 INIT KEY LAYOUT” and press the ENTER key.
↓
Select the file name to be changed and enter the number of records.
DISPLAY: The following display is shown.
The contents of displayed reports are described below.
Select the item with the cursor and press the ENTER key.
– 28 –
FILE TABLE -1
Group NO.
FILE NAME
DISPLAY TEXT
*
File table No.
(Create/Erase)
TYPE
1
Dept
DEPT
1
01,02,03,05
2
Dept Text (8)
DEPT TEXT (8)
0
03
3
Dept Text (16)
DEPT TEXT (16)
0
04
4
Dept Mark Down
DEPT MARK DOWN
0
10
5
PLU
PLU
1
15,16,18,23
6
PLU Price 1
PLU PRICE 1
0
16,23
7
PLU Price 1 to 5
PLU PRICE 1 to 5
0
17,28
8
PLU Text 1 (8)
PLU TEXT 1 (8)
0
18
9
PLU Text 1 (16)
PLU TEXT 1 (16)
0
19
10
PLU Text 1 to 5 (8)
PLU TEXT 1 – 5 (8)
0
20
11
PLU Text 1 to 5 (16)
PLU TEXT 1 – 5 (16)
0
21
12
PLU stock
PLU STOCK
0
22
13
Link PLU
LINK PLU
1
33
14
Set PLU
SET PLU
1
34
15
Condiment table
CONDIMENT TABLE
1
35
16
Mix&Match table
MIX&MATCH TABLE
1
36,37
17
Recipe table
RECIPE TABLE
1
38
18
Ingredient table
INGREDIENT TABLE
1
39,40
19
Ingredient Stock
INGREDIENT STOCK
0
41
20
Server
SERVER
1
50,51,52,53,54
21
Sign off Server for IRC
SIGN OFF SERVER
2
64,65
22
Manager
MANAGER
1
66
23
Employee
EMPLOYEE
1
67,68
24
Employee Sales
EMPLOYEE SALES
1
69
25
Employee working time
EMPLOTEE TIME
1
70
26
Hourly
HOURLY
1
71,72
27
Hourly PLU Group
HOURLY PLU GROUP
0
76
28
Daily net
DAILY NET
1
80,81
29
Reg buffer
REG BUFFER
1
86,87,88,89,122,124
30
KP buffer
KP BUFFER
0
90
31
GLU/PBLU (Preset)
GLU/PBLU (ALL)
1
100
32
Closed GLU
CLOSED GLU
1
101
33
Drive Thru (Preset)
DRIVE THRU (ALL)
1
102
34
Closed Drive Thru
CLOSED DRIVE THRU
1
103
35
Auto GLU Generate
AUTO GLU GEN.
1
104
36
Auto Drive Thru code Generate
DRIVE THURU GEN.
1
105
37
GLU/PBLU Rcv.buffer (IRC)
GLU/PBLU RCV.BUF
2
91
38
KP (IRC)
KP
1
112,113
39
T-LOG Buffer
T-LOG BUFFER
1
93
40
Journal log buffer
J-LOG BUFFER
1
96
41
Receipt Window buffer
RECEIPT WINDOW
1
97
42
Ind. Payment buffer
IND.PAY BUFFER
0
98,99,121,123
43
Term Dept
TERM DEPT
0
06,11
44
Term PLU
TERM PLU
0
24
45
Term Transaction
TERM TRANS
0
46
46
Term Server
TERM SERVER
0
55
47
All of term file
ALL OF TERM FILE
0
06,11,24,46,55
48
GLU/PBLU file (Preset Only)
GLU/PBLU(PRESET)
1
100
49
Drive thru file (Preset Only)
D-THRU (PRESET)
1
102
50
B.T. buffer (Buffer Only)
B.T BUFFER
0
89
– 29 –
DISPLAY: Type 1 input screen
Type 0 Create/Erase only
Type 1 Create/Erase and Increase/dicrease the number of
records or blocks.
Type 2 Create/Erase and Increase/dicrease the number of blocks
** :
The files which are created or erased by the entry of the group
No.
** : For individual erase
When an item of Type 0 is selected, the following display is shown.
DISPLAY: Type 0 input screen
Enter the number of records.
When an item of Type 2 is selected, the following display is shown.
DISPLAY: Type 2 input screen
↓ “SBTL” key
Enter the number of blocks.
Selection of CREATE/ERASE is performed.
When an item of Type 1 is selected, the following display is shown.
– 30 –
FILE TABLE -2
Table
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
File Name
Dept. peset
price
text(8)
text(16)
Daily
Term
Save Daily
Consolidation
Receive
Daily(markdown)
Term(markdown)
Save Daily(markdown)
Consolidation (markdown)
Receive(markdown)
PLU preset
price1
price1-5
text1(8)
text1(16)
text1-5(8)
text1-5(16)
stock
Daily(price1)
Term(price1)
Save Daily(price1)
Consolidation(price1)
Receive(price1)
Daily(price1-5)
Term(price1-5)
Save Daily(price1-5)
Consolidation(price1-5)
Receive(price1-5)
Link PLU
Set PLU
Condiment table
Mix&Match table
Mix&Match sale buffer
Recipe table
Ingredient table
Ingredient text
Ingredient stock
Ingredient Consolidation
Ingredient Receive
Transaction Label
Daily
Term
Save Daily
Consolidation
Receive
Server preset
flag
Name
Server Transaction Label
Daily
Term
Save Daily
Consolidation
Receive
Total server(Buffer) Label
Total
Receive server Preset
Flag
MRS
10
10
10
0
10
10
0
0
0
0
0
0
0
0
500
500
0
500
0
0
0
0
500
500
0
0
0
0
0
0
0
0
30
10
10
10
10
500
999
999
999
0
0
119
119
119
0
0
0
10
10
10
74
74
74
0
0
0
74
74
0
0
Record
Max
99
99
99
99
99
99
99
99
99
99
99
99
99
99
*****
*****
*****
*****
*****
*****
*****
*****
*****
*****
*****
*****
*****
*****
*****
*****
*****
*****
99
99
99
99
99
999
999
999
999
999
999
119
119
119
119
119
119
255
255
255
74
74
74
74
74
74
74
74
255
255
– 31 –
#1
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(15)
(15)
(15)
(15)
(15)
(15)
(15)
(15)
(15)
(15)
(15)
(15)
(15)
(15)
(15)
(15)
(15)
(36)
(38)
(38)
(38)
(38)
(38)
(44)
(44)
(44)
(44)
(44)
(50)
(50)
(53)
(53)
(53)
(53)
(53)
(53)
(53)
(50)
(50)
MRS
1
1
1
0
1
1
0
0
0
0
0
0
0
0
1
1
0
1
0
0
0
0
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
10
10
10
0
0
0
1
1
0
0
Block
Max
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
255
255
255
255
255
255
1
1
1
1
#1
(50)
(50)
(50)
(50)
(50)
(50)
Label
Size
1
0
0
0
0
0
0
0
0
0
0
0
0
0
5
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
2
2
0
0
0
0
2
0
0
0
0
0
2
0
0
2
0
0
0
0
0
2
0
2
0
Data
Size
12
3
8
16
9
9
9
9
9
8
8
8
8
8
33
3
15
8
16
40
80
8
9
9
9
9
9
9
9
9
9
9
15
75
61
5
5
60
3
8
4
4
4
0
8
8
8
8
8
23
3
8
0
8
8
8
8
8
0
8
23
3
Table
No.
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
File Name
Name
Sign off Server Transaction Label
Receive
Manager
Employee Label
Name
Employee Sales
Employee working time
Hourly Label
Daily
Save Daily
Consolidation
Receive
PLU group Daily
Save Daily
Consolidation
Receive
Daily Net Label
Total
Daily Net Consolidation Label
Consolidation
Daily Net Receive Label
Receive
REG Buffer
REG Edit Buffer
GLU/PBLU Buffer
B.T. Buffer
KP Buffer
GLU/PBLU Receive Buffer
GLU/PBLU Save Buffer
T-Log Buffer
T-Log Receive Buffer
Sorted Top 20 Buffer
Journal Log Buffer
Receipt Window Buffer
Individual Payment Edit Buffer
Individual Pay GLU/PBLU Buffer
GLL/PBLU
Closed GLU
Drive Thru
Closed Drive Thru
GLU code Auto Generate
Drive Thru code Auto Generate
Logo Text
Function Text
Dept. Group Text
PLU Group Text
Hourly Group Text
Currency Conversion Text
KP Preset
KP Text
Job Location Table
Job Location Text
Direct key Table
Scale Table
Auto key table
Stacked report Table
Employee time buffer
Individual Payment REG Buffer
Bill buffer
Individual Payment Itemizer Buffer
Copy Buffer
MRS
0
0
0
5
20
20
20-40
20-100
96
96
0
0
0
96
0
0
0
32
32
0
0
0
0
250
250
250
250
250
0
0
1500
0
20
100
30
0
0
50-500
0
50-500
0
41
41
15
168
9
99
9
9
9
9
99
99
156
9
25
20
20
0
250
0
250
Record
Max
255
74
74
99
****
****
****-****
****-****
96
96
96
96
96
96
96
96
96
32
32
32
32
32
32
*****
*****
*****
*****
*****
*****
*****
*****
*****
99
***
***
*****
*****
****-****
****-****
****-****
****-****
**
**
15
168
9
99
9
9
9
9
99
99
156
9
25
20
20
*****
*****
100
****
– 32 –
#1
(50)
(53)
(53)
(67)
(71)
(71)
(71)
(71)
(71)
(71)
(71)
(71)
(80)
(80)
(80)
(80)
(80)
(86)
(86)
(86)
(86)
(86)
(86)
(86)
(86)
(86)
(112)
(114)
(86)
(86)
(86)
Block
Max
MRS
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
#1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Label
Size
0
2
0
1
5
0
11
11
1
0
0
0
0
0
0
0
0
3
0
3
0
3
0
0
0
0
0
0
0
0
0
0
8
0
5
0
0
10
10
10
10
0
0
1
2
1
1
1
1
1
0
1
0
1
1
2
1
0
0
0
1
0
Data
Size
8
0
8
2
11
8
17
16
0
11
11
11
11
9
9
9
9
0
8
0
8
0
8
48
48
48
48
48
48
48
26
26
2
44
23
48
48
45
45
45
45
4
4
40
8
8
8
8
4
4
12
5
8
15
2
50
12
19
48
48
345
48
DISPLAY: The following display is shown.
[SUPERVISOR ON/OFF]
DISPLAY: Setting item select screen
Select the item with the cursor and press the ENTER key.
Select “9 SUPERVISOR ON/OFF” and press the ENTER
key.
[MEMORY INITIAL]
↓
DISPLAY: Setting item select screen
DISPLAY: SUPERVISOR ON/OFF screen 1/2
Select “10 MEMORY INITIAL” and press the ENTER key.
Press “SBTL” key and the setting item select screen is
shown.
↓
↓
DISPLAY: The following display is shown.
DISPLAY: SUPERVISOR ON/OFF screen 2/2
Select the item with the cursor and press the ENTER key.
Select the item and press the ENTER key.
↓
– 33 –
[SSP]
[IR DATA SEND]
DISPLAY: Setting item select screen
DISPLAY: Setting item select screen
Select “11 SSP” and press the ENTER key.
Select “12 IR DATA SEND” and press the ENTER key.
↓
↓
DISPLAY: SSP screen
DISPLAY: IR DATA SEND screen
↓
↓
Select the item with the cursor and press the ENTER key.
Select the item and press the ENTER key.
The contents of items are shown in the table below.
DISPLAY TEXT
The contents of items are shown in the table below.
CONTENTS
SSP INPUT
Used for SSP data input
SSP EDIT
Used for edit of entered SSP data.
SSP ALL CLEAR
Used to erase all the entered SSP data.
SSP IND. CLEAR
Used to erase entered SSP data individually.
SSP REACTIV.
Used to restore erased SSP data.
– 34 –
DISPLAY TEXT
TO
SEND DATA
CONTENTS
SELECT ITEM
IR
communication
format setting
ECR(IrDA)
Send content
select
ALL RAM
[IR DATA RECEIVE]
MRS
★
DISPLAY: Setting item select screen
ECR(ASK)
ER-02FD(ASK)
★
STANDARD RAM
03MB/04MB(1)
03MB/04MB(2)
04MB(3)
04MB(4)
SSP
RESERVED 1
RESERVED 2
SPEED
Communication
speed setting
PROGRAMMED SPEED
★
115200bps
57600bps
38400bps
19200bps
Select “13 IR DATA RECEIVE” and press the ENTER key.
9600bps
↓
4800bps
2400bps
DISPLAY: IR DATA RECEIVE screen
↓
Select the item and press the ENTER key.
The contents of items are shown in the table below.
DISPLAY TEXT
FROM
SPEED
CONTENTS
SELECT ITEM
IR
communication
format setting
ECR(IrDA)
Communication
speed setting
PROGRAMMED SPEED
★
ECR(ASK)
ER-02FD(ASK)
115200bps
57600bps
38400bps
19200bps
9600bps
4800bps
2400bps
– 35 –
MRS
★
[1 TERMINAL SETTING]
CHAPTER 5. IRC SETTING
DISPLAY: IRC SETTING item select screen
DISPLAY: SRV mode screen
Select “1 TERMINAL SETTING” and press the ENTER
key.
Select “3 IRC SETTING” and press the ENTER key.
↓
↓
DISPLAY: Setting item select screen
DISPLAY: TERMINAL SETTING screen
↓
Select the item and press the ENTER key.
↓
Select the item to be changed and press the ENTER key.
The item setting input screen is shown.
The contents of setting are shown in the table below.
– 36 –
[1 SATELLITE] [2 MASTER]
[4 STD. WITH IRC]
DISPLAY: Setting screen
DISPLAY: Setting screen
DISPLAY TEXT
CONTENTS
SELECT ITEM MRS NOTE
TERMINAL No.
Terminal
number
000 ∼ 254
GLU SYSTEM
GLU system
CENTRALIZED
DISPLAY TEXT
CONTENTS
000
TERMINAL No.
Terminal number
★
INDIVIDUAL
D-THRU SYSTEM Drive thry
system
CENTRALIZED
[5 STAND ALONE]
★
INDIVIDUAL
BACKUP MASTER Backup master NOT
function
EXIST
Used to restore to a stand alone machine.
★
[3 BUCKUP MASTER]
DISPLAY: Setting screen
DISPLAY TEXT
CONTENTS
SELECT ITEM MRS NOTE
TERMINAL No.
Terminal
number
000 ∼ 254
GLU SYSTEM
GLU system
CENTRALIZED
000
★
INDIVIDUAL
D-THRU SYSTEM Drive thry
system
CENTRALIZED
★
INDIVIDUAL
– 37 –
SELECT
MRS NOTE
ITEM
000 ∼ 254 000
COPYRIGHT  1997 BY SHARP CORPORATION
All rights reserved.
Printed in the USA.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted,
in any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise,
without prior written permission of the publisher.
SHARP CORPORATION
Information Systems Group
Quality & Reliability Control Center
Yamatokoriyama, Nara 639-11, Japan
January 1997 Printed in the USA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising