Onkyo DV-SP300 User Guide Manual Operating Instruction Pdf

Onkyo DV-SP300 User Guide Manual Operating Instruction Pdf
Contents
Before Using Your DVD Player
2
Getting Started
6
DVD Player
DV-SP300
Facilities and Connections
10
Basic Operation
17
Advanced Operation
20
Function Setup
30
Others
37
Instruction Manual
Thank you for purchasing the Onkyo DVD Player.
Please read this manual thoroughly before making
connections and turning on the power.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new DVD Player.
Please retain this manual for future reference.
E
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING
AVIS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
Important Safeguards
1. Read Instructions – All the safety and operating
instructions should be read before the appliance is operated.
2. Retain Instructions – The safety and operating instructions
should be retained for future reference.
3. Heed Warnings – All warnings on the appliance and in the
operating instructions should be adhered to.
4. Follow Instructions – All operating and use instructions
should be followed.
5. Cleaning – Unplug the appliance from the wall outlet before
cleaning. The appliance should be cleaned only as
recommended by the manufacturer.
6. Attachments – Do not use attachments not recommended by
the appliance manufacturer as they may cause hazards.
7. Water and Moisture – Do not use the appliance near water –
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool; and
the like.
8. Accessories – Do not place the appliance on an unstable
cart, stand, tripod, bracket, or table. The appliance may fall,
causing serious injury to a child or adult, and serious damage
to the appliance. Use only with a cart, stand, tripod, bracket, or
table recommended by the manufacturer, or sold with the
appliance. Any mounting of the
appliance should follow the
PORTABLE CART WARNING
manufacturer’s instructions, and
should use a mounting accessory
recommended by the manufacturer.
9. An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance and
S3125A
cart combination to overturn.
10. Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the appliance
and to protect it from overheating, and these openings must not
be blocked or covered. The openings should never be blocked
by placing the appliance on a bed, sofa, rug, or other similar
surface. The appliance should not be placed in a built-in
installation such as a bookcase or rack unless proper
ventilation is provided. There should be free space of at least
5 cm (2 in.) and an opening behind the appliance.
11. Power Sources – The appliance should be operated only
from the type of power source indicated on the marking label.
If you are not sure of the type of power supply to your home,
consult your appliance dealer or local power company.
12. Grounding or Polarization – The appliance may be
equipped with a polarized alternating current line plug (a plug
having one blade wider than the other). This plug will fit into
the power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try reversing
the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
2
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
13. Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention
to cords at plugs, convenience receptacles, and the point where
they exit from the appliance.
14. Lightning – For added protection for the appliance during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the appliance due to lightning and power-line surges.
15. Overloading – Do not overload wall outlets, extension cords,
or integral convenience receptacles as this can result in a risk
of fire or electric shock.
16. Object and Liquid Entry – Never push objects of any kind
into the appliance through openings as they may touch
dangerous voltage points or short-out parts that could result in
a fire or electric shock. Never spill liquid of any kind on the
appliance.
17. Servicing – Do not attempt to service the appliance yourself
as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified
service personnel.
18. Damage Requiring Service – Unplug the appliance form
the wall outlet and refer servicing to qualified service
personnel under the following conditions:
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have fallen into the
appliance,
C. If the appliance has been exposed to rain or water,
D. If the appliance does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the appliance to its normal operation,
E. If the appliance has been dropped or damaged in any way, and
F. When the appliance exhibits a distinct change in
performance – this indicates a need for service.
19. Replacement Parts – When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same characteristics
as the original part. Unauthorized substitutions may result in
fire, electric shock, or other hazards.
20. Safety Check – Upon completion of any service or repairs to
the appliance, ask the service technician to perform safety
checks to determine that the appliance is in proper operation
condition.
21. Wall or Ceiling Mounting – The appliance should be
mounted to a wall or ceiling only as recommended by the
manufacturer.
22. Heat – The appliance should be situated away from heat
sources such as radiators, heat registers, stoves, or other
appliances (including amplifiers) that produce heat.
23. Liquid Hazards – The appliance should not be exposed to
dripping or splashing and no objects filled with liquids, such as
vases should be placed on the appliance.
Precautions
This unit contains a semiconductor laser system and is classified as
a “CLASS 1 LASER PRODUCT”. So, to use this model properly,
read this Instruction Manual carefully. In case of any trouble,
please contact the store where you purchased the unit. To prevent
being exposed to the laser beam, do not try to open the enclosure.
The label below is applied on the rear panel except for USA and
Canadian models.
CAUTION:
VISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK
FAILED OR DEFEATED. DO NOT STARE INTO BEAM.
CAUTION:
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS
OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
1. This unit is a CLASS 1 LASER PRODUCT and employs a
laser inside the cabinet.
2. To prevent the laser from being exposed, do not remove
the cover. Refer servicing to qualified personnel.
For U.S. model
For Canadian model
The laser is covered by a housing which prevents exposure during
operation or maintenance. However, this product is classified as a
Laser Product by CDRH (Center for Devices and Radiological
Health) which is a department of the Food and Drug
Administration. According to their regulations 21 CFR section
1002.30, all manufactures who sell Laser Products must maintain
records of written communications between the manufacturer,
dealers and customers concerning radiation safety. If you have any
complaints about instructions or explanations affecting the use of
this product, please feel free to write to the address on the back
page of this manual. When you write us, please include the model
number and serial number of your unit.
In compliance with Federal Regulations, the certification,
identification and the period of manufacture are indicated on the
rear panel.
This class B digital apparatus complies with Canadian ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Modèle pour les Canadien
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
Sur les modèles dont la fiche est polarisee:
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
FCC INFORMATION FOR USER
CAUTION:
The user changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
3
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Precautions
1. Regional Restriction Codes (Region Number)
Regional restriction codes are built into DVD Players and
DVD-Video media for each sales region. If the regional code of
the DVD Player does not match one of the regional codes on
the DVD-Video, playback is not possible.
The regional number can be found on the rear panel of the
DVD Player. (e.g.
1
for Region 1)
2. About This Manual
This manual explains the basic procedures for operating the
DVD Player. Some DVD-Video discs do not support the full
potential of the DVD technology. Your DVD Player may
therefore not respond to all operating commands. Refer to
instruction notes on discs.
A “ ” mark may appear on the TV screen during operation. It
means that the operation is not permitted by the DVD Player or
the disc.
3. Recording Copyright
Recording of copyrighted material for other than personal use
is illegal without permission of the copyright holder.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST
TIME, READ THE FOLLOWING SECTION CAREFULLY.
The voltage of the available power supply differs according to
country or region. Be sure that the power supply voltage of the
area where the unit will be used meets the required voltage
(e.g., AC 120 V, 60 Hz) written on the rear panel.
5. Do not touch the unit with wet hands
Do not handle the unit or power cord when your hands are wet
or damp. If water or any other liquid enters the case, take the
unit to an authorized service center for inspection.
6. Location of the unit
• Place the unit in a well-ventilated location.
Take special care to provide plenty of ventilation on all sides
of the unit especially when it is placed in an audio rack. If
ventilation is blocked, the unit may overheat and
malfunction.
• Do not expose the unit to direct sunlight or heating units as
the unit’s internal temperature may rise and shorten the life
of the pickup.
• Avoid damp and dusty places and places directly affected by
vibrations from the speakers. In particular, avoid placing the
unit on or above one of the speakers.
• Be sure the unit is placed in a horizontal position. Never
place it on its side or on a slanted surface as it may
malfunction.
• When you place the unit near a TV, radio, or VCR, the
playback picture may become poor and the sound may be
distorted. In this case, place the unit away from the TV,
radio, or VCR.
7. Care
From time to time you should wipe the front and rear panels
and the cabinet with a soft cloth. For heavier dirt, dampen a
soft cloth in a weak solution of mild detergent and water, wring
it out dry, and wipe off the dirt. Following this, dry
immediately with a clean cloth.
Do not use rough material, thinners, alcohol or other chemical
solvents or cloths since these could damage the finish or
remove the panel lettering.
4
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
8. Notes on Handling
• When shipping the unit, use the original shipping carton and
packing materials. For maximum protection, repack the unit
as it was originally packed at the factory.
• Do not use volatile liquids, such as insect spray, near the
unit. Do not leave rubber or plastic products in contact with
the unit for a long time. They will leave marks on the finish.
• The top and rear panels of the unit may become warm
after a long period of use. This is not a malfunction.
• When the unit is not in use, be sure to remove the disc and
turn off the power.
• If you do not use the unit for a long period, the unit may not
function properly in the future. Turn on and use the unit
occasionally.
9. To Obtain a Clear Picture
The unit is a high technology, precision device. If the optical
pick-up lens and disc drive parts are dirty or worn down, the
picture quality becomes poor. To obtain a clear picture, we
recommend regular inspection and maintenance (cleaning or
parts replacement) every 1,000 hours of use depending on the
operating environment. For details, contact your nearest dealer.
10. Notes on Moisture Condensation
Moisture condensation damages the unit.
Please read the following carefully.
• What is moisture condensation?
Moisture condensation occurs, for example, when you pour a
cold drink into a glass on a warm day. Drops of water form
on the outside of the glass. In the same way, moisture may
condense on the optical pick-up lens inside the unit, one of
the most crucial internal parts of the unit.
• Moisture condensation occurs in the following
cases.
– When you bring the unit directly from a cold place to a
warm place.
– When you use the unit in a room where you just turned on
the heater, or a place where the cold wind from the air
conditioner directly hits the unit.
– In summer, when you use the unit in a hot and humid
place just after you move the unit from an air conditioned
room.
– When you use the unit in a humid place.
• Do not use the unit when moisture condensation
may occur.
If you use the unit in such a situation, it may damage discs
and internal parts. Remove the disc, connect the power cord
of the unit to the wall outlet, turn on the unit, and leave it for
two or three hours. After a few hours, the unit will have
warmed up and evaporated any moisture. Keep the unit
connected to the wall outlet and moisture condensation will
seldom occur.
Table of Contents
Important Safeguards / Precautions / Table of Contents ............................ 2 - 5
Getting Started
Notes on Discs .................................................................................................... 6
Playable Discs / The Structure of the Disc Content / About Video CDs /
MP3 Compatibility Information / Handling Discs / Cleaning Discs /
Storing Discs / Notes on Copyright
Features/Supplied Accessories ......................................................................... 8
Features / Supplied Accessories
Preparing the Remote Controller ....................................................................... 9
Inserting the Batteries / Using the Remote Controller
Facilities and Connections
Control Position and Names ............................................................................ 10
Front Panel / Rear Panel / Display / Remote Controller
Making Connections ......................................................................................... 14
Connections to a TV / Optional Video Connections / Optional Audio Connections
Basic Operations
Turning on .......................................................................................................... 17
Connecting the POWER
Basic Playback .................................................................................................. 18
Starting Playback / Various Playback
Advanced Operations
Using Banner Display ....................................................................................... 20
Using the on-screen Banner Display / Selecting a Title /
Selecting a Chapter or Track / Selecting a Playback Audio Setting /
Changing the Subtitle Language / Changing the Camera Angle / Using
IntroScan Function / Using a Bookmark
Other Operations .............................................................................................. 25
Progressive Scan Function (NTSC Video Output Only) / Random Play /
Repeat Play / A-B Repeat Play / Memory Edit Play
MP3 Function .................................................................................................... 28
MP3 On-screen Display / Playing Back MP3 / Selecting MP3 Files /
MP3 Repeat Play / MP3 Memory Play
Function Setup
Customizing the Settings ................................................................................. 30
Making Adjustments to Setting / Language Setting / Operation Setting /
Picture Setting / Audio Setting
Table of Languages ........................................................................................... 36
Table of Language and Their Code No.
Others
Troubleshooting ................................................................................................ 37
Specifications .................................................................................................... 38
5
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Notes on Discs
This section shows you how to handle, clean, and store discs.
The Structure of the Disc Content
Playable Discs
This DVD Player can playback the following discs.
Disc mark
DVDVideo
Video
CD
Contents
Disc size
Audio
+
Video
(moving
pictures)
12 cm
Audio +
Video
(moving
pictures)
Title 1
Chapter 1 Chapter 2
Audio
Title 2
Chapter 1 Chapter 2 Chapter 3
8 cm
12 cm
8 cm
Video CD/CD
Video CD and CD are divided into tracks.
Track 1
CD
CD-R*
DVD-Video
Normally, the contents of DVD-Video are divided into titles, and the
titles are subdivided into chapters.
Track 2
Track 3
Track 4
Track 5
12 cm
8 cm (CD single)
CD-RW*
* The DVD Player can play CD-R/RW discs recorded in
CD-DA format, or with MP3 audio files. Some CD-R/RW
discs may not be able to be played back.
• You cannot play discs such as CD-ROM, DVD-Audio, DVDRAM, DVD-RW, etc., even if the marks in the above table are
labeled on those discs.
• The North American version of this DVD Player outputs NTSC
format video only. Other models output NTSC or PAL depending
on the format used by the disc currently being played. DVD discs
that use other video formats (e.g., SECAM) cannot be played on
this DVD Player.
• Avoid using heart-shaped or octagonal discs. Playing irregularly
shaped discs may damage the internal mechanism of the DVD
Player.
Discs with shapes such
as these cannot be
played.
• Do not use discs that have residue from adhesive tape, rental discs
that have peeling labels, or discs that have custom labels or
stickers. Otherwise, you may not be able to eject the discs or the
DVD Player may become inoperative.
• Use CD-R or CD-RW media for recording your CD audio files or
MP3 files. The disc must be finalized in order to play.
6
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
About Video CDs
This DVD Player supports Video CDs equipped with the PBC
(Version 2.0) function. (PBC is the abbreviation of Playback
Control.) You can enjoy two playback variations depending on the
type of disc.
• Video CD not equipped with PBC function (Version 1.1)
Sound and movies can be played on this DVD Player in the same
way as a CD.
• Video CD equipped with PBC function (Version 2.0)
In addition to operation of the Video CD not equipped with the
PBC function, you can enjoy playback with interactive software
and search function using the menu displayed on the TV screen
(Menu Playback). Some of the functions described in this
Instruction Manual may not work with some discs.
MP3 Compatibility Information
• This system is not compatible with mult-session discs.
If you try a multi-session disc, only the first session will
be played.
• The CD-R or CD-RW must be ISO 9660 level 1 compatible.
• Files should be MPEG1 Audio Layer 3 format, 32 kHz, 44.1 kHz
(recomended) or 48 kHz, 32 kbps - 320 kbps (128 kbps
recomended). Incompatible files will not play.
• This system only plays tracks that are named with the file
extension “.mp3” or “.MP3”.
Handling Discs
Notes on Copyright
• Do not touch the playback side of the disc.
Playback side
• Do not attach paper or tape to discs.
It is forbidden by law to copy, broadcast, show, broadcast on cable,
play in public, and rent copyrighted material without permission.
The video recorded on DVD-Video is copy protected, and any
recordings made from these discs will be distorted.
This product incorporates copyright protection technology that is
protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation, and is intended for
home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
Cleaning Discs
• Fingerprints and dust on the disc cause picture and sound
deterioration. Wipe the disc from the center outwards with a soft
cloth. Always keep the disc clean.
• If you cannot wipe off the dust with a soft cloth, wipe the disc
lightly with a slightly moistened soft cloth and finish with a dry
cloth.
• Do not use any type of solvent such as thinner, benzine,
commercially available cleaners or antistatic spray for vinyl LPs.
It may damage the disc.
Storing Discs
• Do not store discs in a place subject to direct sunlight or near heat
sources.
• Do not store discs in places subject to moisture and dust such as a
bathroom or near a humidifier.
• Store discs vertically in a case. Stacking or placing objects on
discs outside of their case may cause warping.
7
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Features/Supplied Accessories
Features
●
●
●
●
●
●
●
●
●
●
Plays DVD-Video Discs, Video CDs, CDs
10-bit Video DAC
Simultaneous output to all video connections
Digital Outputs pass DTS®*1, Dolby®*2 Digital and PCM Signals
Built-In Dolby® Digital decoder
Full-function remote controller
Direct Digital Path
CD-R and CD-RW playable
Plays MP3
Pass 96 kHz PCM digital stream
*1 “DTS” and “DTS Digital Out” are trademarks of Digital Theater
Systems, Inc.
*2 Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
Supplied Accessories
Make sure your box contains everything listed below.
If any pieces are missing, contact your nearest Onkyo dealer.
The number of accessories is indicated in brackets [ ].
Remote controller (RC-501DV) [1]
Audio/video cable [1]
Batteries (size AAA/R3) [2]
Coaxial cable [1]
Conversion plug [1]
This plug is not supplied for North America models.
Shape may vary depending on the area in which it was purchased. Use
this plug if the power cord plug of the DV-SP300 does not fit your
AC outlet.
8
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Preparing the Remote Controller
Point the remote controller toward the remote control sensor.
Remote control sensor
30˚
Ap
p
ro
x.
16
30˚
t
1 Remove the battery compartment cover by
pressing the tab and lifting up the cover.
Using the Remote Controller
fe
e
Inserting the Batteries
2 Insert the two batteries (size AAA/R3).
Be sure to match the + and – ends of the batteries
with the diagram inside the battery compartment.
Notes
3 Replace the battery compartment cover.
• Place the unit away from strong light such as direct sunlight or inverted
fluorescent light which can prevent proper operation of the remote
controller.
• Using another remote controller of the same type in the same room or using
the unit near equipment which uses infrared rays may cause operational
interference.
• Do not put any object such as a book on the remote controller. The buttons
of the remote controller may be pressed by mistake and drain the batteries.
• Make sure the audio rack doors do not have colored glass. Placing the unit
behind such doors may prevent proper remote controller operation.
• If there is any obstacle between the remote controller and the remote
control sensor, the remote controller will not operate.
Notes
• Do not mix new batteries with old batteries or different kinds of
batteries.
• To avoid corrosion, remove the batteries if the remote controller
is not to be used for a long time.
• Remove dead batteries immediately to avoid damage from
corrosion. If the remote controller does not operate smoothly,
replace both batteries at the same time.
• The life of the batteries supplied is about six months but this
will vary depending on usage.
9
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Control Position and Names
Front Panel
For operational instructions, see the page indicated in brackets [ ].
1 2
3
4
7
1 POWER button [17]
Turns on the main power supply.
2 STANDBY indicator [17]
5
8
6
9
0
6 PLAY/PAUSE £/8 button [18]
Begins to play disc (close disc tray first if it is open.)
Temporarily stops playback when a disc is playing. Press this
button again for normal playback.
Lights in the standby mode.
7 Disc tray [18]
3
STANDBY/ON button [17]
Toggle for standby on and off.
4 Display [12]
5 STOP 7 button [18]
Stops playing a disc. When disc is playing, if you press 7 and
£, the disc will start resume play. When 7 is pressed again
during stop mode, the resume function is canceled.
8 0 OPEN/CLOSE button [18]
Press to open or close the disc tray.
9 SKIP 4/¢ buttons [19]
Allow you to move to the previous chapter or track / the next
chapter or track on a disc.
0 SEARCH 1/¡ buttons [19]
Allow you to search in reverse through a disc while it is in play
mode. Each time you press this button, search speed changes.
10
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Control Position and Names
Rear Panel
For operational instructions, see the page indicated in brackets [ ].
VIDEO OUTPUT
COMPONENT
DIGITAL
OUTPUT
OPTICAL
ANALOG
OUTPUT
COAXIAL
1 2 3
PR
DVD PLAYER
MODEL NO. DV-SP300
L
VIDEO
PB
R
S VIDEO
Y
4
5 6
1 DIGITAL OUTPUT OPTICAL jack [16]
Use optical cable to connect your DVD Player to an AV
component that features digital input capability. If the
component has a Dolby Digital or DTS decoder, you can enjoy
theater-quality multichannel sound.
2 DIGITAL OUTPUT COAXIAL jack [16]
Use coaxial cable to connect your DVD Player to an AV
component that features digital input capability. If the
component has a Dobly Digital or DTS decoder, you can enjoy
theater-quality multichannel sound.
3 ANALOG OUTPUT jacks [14, 16]
Insert audio cables (left and rights) to these jacks on your DVD
Player and to the corresponding Audio Input jacks (left and
right) on your TV or receiver.
4 VIDEO OUTPUT VIDEO jack [14]
Connect a video cable to this jack and to the Video Input jack on
your TV.
5 VIDEO OUTPUT S VIDEO jack [15]
If your TV has a S-Video jack, you can connect an S-Video
cable to your TV and to your DVD Player for improved video
quality. The S-Video cable only carries the video signal;
remember to connect the left and right audio cables.
6 VIDEO OUTPUT COMPONENT (PR/PB/Y) jacks
[15]
If your TV has component inputs, you can connect a component
video cable to your TV and to your DVD Player for ideal video
quality. The component video cable only carries the video
signal; remember to connect the left and right audio cables.
If you connect a TV that is compatible with a Progressive scan
signal, you can enjoy both Interlaced and Progressive scan.
Note
• Progressive scan only works with NTSC format discs.
11
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Control Position and Names
Display
For operational instructions, see the page indicated in brackets [ ].
12
DVD
CD
VCD
MP3
3
4 5 6 7
PROGRESSIVE
RESUME
TITLE
8
RANDOM REPEAT 1ALL
CHAPTER
TRACK
~!
1 Inserted disc indicators
9 0 - =
A-B
INTRO
HOUR
MEM.
MIN
PBC
SEC
@
■ Display Examples
Indicate the type of current disc that is loaded.
During DVD-Video playback:
2 Play/Pause indicators
DVD
Illuminate in play or pause mode.
TITLE
CHAPTER
MIN
SEC
3 PROGRESSIVE indicator
Playing chapter
3 of title 2
Illuminates when the DVD player is set to progressive mode.
4 TITLE indicator
Illuminates to indicate the current title number.
5 RESUME indicator
Illuminate when the player is ready for resume playback.
Notes
Elapsed time of
the current
chapter
• Some discs may not display chapter numbers.
• A time indication not accompanied with a chapter number shows elapsed
time of a segment within the current time.
During Video CD playback:
6 CHAPTER/TRACK indicators
TRACK
Indicate display mode of the current chapter of DVD disc or
track number of Video CD or CD.
Playing track 3
7 RANDOM indicator
Illuminates during random playback.
MIN
SEC
VCD
Note
Elapsed time of
the current track
Some discs may not display track numbers or elapsed time.
8 REPEAT indicators
Illuminate during repeat playback.
9 INTRO indicator
During CD playback:
TRACK
CD
MIN
SEC
Illuminates during intro-scan playback.
Playing track 3 Elapsed time of
the current track
0 MEM. indicator
Illuminates during memory playback.
During MP3 playback:
- PBC indicator
Illuminates when PBC is on for Video CD.
CD
TRACK
MIN
SEC
MP3
= Time indicator
Indicate playing time.
~ Playback status indicator
Illuminates (rotating) when the disc plays.
! Parental Lock indicator
Illuminates in parental lock mode.
@ Multifunction indicator
Indicates operating status, messages, etc.
12
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Playing track 105 Elapsed time of
of folder 6
the current track
Notes
• If the track is within a folder, the folder number is displayed. For tracks
outside a folder, no folder number is displayed.
• Track number is consecutive.
Control Position and Names
Remote Controller
For operational instructions, see the page indicated in brackets [ ].
1
@
2
#
3
$
4
%
5
^
6
7
&
*
(
)
8
7 ON SCREEN button [20-24]
Press this button while you’re playing a disc to see Banner Display
on the screen. The Banner Display contains various playback
features and gives you the information about the disc you’re
playing.
8 MENU button [30]
Displays the DVD Disc Menu on the TV screen in play mode and
Setup Menu in stop mode.
9 Cursor buttons (5/∞/2/3) [20-25, 27-30]
Use the cursor buttons to select the items or settings.
0 ENTER button [20-25, 27-30]
Press this button to select and execute a highlighted menu item.
- TOP MENU button [31]
Press to call up the top menu programmed on the DVD.
Depending on the DVD, the top menu may be identical to DVD
menu or title menu. When playing a Video CD equipped with PBC
function, DVD Player will automatically enter the PBC on mode.
Press once to turn PBC off and press again to turn on.
= AUDIO button [22]
Press to select various audio languages on a disc. When playing a
Video CD, press to select the audio channel.
~ Number buttons (0~9) [21]
9
Select numbers by pressing these buttons.
! MEMORY button [27, 29]
0
-
_
@ 0 OPEN/CLOSE button [18]
=
+
# SLOW
Press to see Memory Edit Display on the screen in stop mode.
Press to open or close the disc tray.
/
buttons [19]
Allow you to play movies in slow mode. Each time you press this
button, slow speed will be changed. In the case of Video CD,
reverse SLOW cannot be activated.
~
$ STEP e/E buttons [19]
Freeze a picture when a disc is playing. Also the picture advances
frame by frame each time to press these buttons. In case of
Video CD, reverse STEP can not be activated.
!
¡
% DOWN 4 / UP ¢ buttons [19, 28]
Allow you to move to the previous chapter or track / the next
chapter or track on a disc.
^ FR 1 / FF ¡ buttons [19]
Allow you to search in reverse or forward through a disc while it is
in play mode. Each time you press these buttons, search speed
changes.
& PLAY £ button [18, 28]
1
Begins to play disc (close disc tray first if it is open.)
STANDBY/ON button [17]
Toggle for standby on and off.
2 DIMMER button [19]
Toggle to control the lightness of the display (3 steps).
3 RANDOM button [25]
Press to do random playback.
4 REPEAT button [26, 29]
Press to go to the Repeat menu. You can repeat a title, chapter,
track or one or entire discs.
5 A-B button [26]
Press to play section A-B repeatedly.
6 STOP 7 button [18, 28]
Stops playing a disc. When a disc is playing, if you press 7 and
£, the disc will start resume play. When 7 is pressed again
during stop mode, the resume function is canceled.
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
* PAUSE 8 button [19]
Temporarily stops playback when a disc is playing. Press PLAY
£ button for normal playback.
( SUBTITLE ON/OFF button [22]
Turns the subtitles on and off when playing a DVD.
) SUBTITLE button [22]
Press to select various subtitle language on a disc.
_ RETURN button [28, 30]
When you’re using the DVD Player’s menu system, press this
button to return to the preceding menu screen.
+ PROGRESSIVE SCAN button [25]
Press to display Progressive or Interlaced Icon on TV. Press again
while displayed to switch between Progressive and Interlaced.
¡ CLEAR button [20, 22-26, 29]
Press to clear entered values and settings. Also Banner menu and
OSD menu is removed from the screen when this button is pressed.
13
Making Connections
To accommodate a wide range of home entertainment systems, this player features numerous connection types for both audio and video. Please
refer to the instructions on this and the following pages to determine the best possible type of connections for your system.
Before Connecting
• Refer to the instruction manuals supplied with any and all components that
you plan to connect the DVD Player to.
• Be sure to turn off the power of all components to be connected and unplug
them from the wall outlet before making any connections.
• Connect the DVD Player to the TV or AV component directly. If you connect
the DVD Player to a VCR, TV/VCR combination, or video selector, the
playback picture may be distorted as DVD Video images are copy protected.
• Please note that video connections to a TV or monitor are necessary because
some discs require on-screen menu interaction before they can be played.
• Connect the plugs securely.
Incomplete
Inserted completely
Connections to a TV
The diagram below shows how to make connections to a TV with built-in stereo speakers using the supplied audio/video cable. After making the
connections on this page, you will be able to start using the DVD Player.
Be sure to set TV Aspect after connection using the setup menu explained in “Customizing the Settings” starting on
page 30.
VIDEO
OUTPUT
COMPONENT
DIGITAL
OUTPUT
OPTICAL
COAXIAL
ANALOG
OUTPUT
PR
DVD PLAYER
MODEL NO. DV-SP300
L
VIDEO
PB
R
S VIDEO
Y
Connect the power
cord after all
connections are
complete.
Audio/video cable (supplied)
To video input
Audio (L)
Audio (R)
To audio inputs
Using the supplied audio/video connection
cable
Video
Audio (L)
Using the supplied audio/video cable, make audio connections from
the ANALOG OUTPUT L and R jacks to the corresponding audio
input jacks on the TV.
In the same manner, make the video connection from the VIDEO
OUTPUT VIDEO jack to the corresponding video input jack on the
TV.
Note
• Be sure to match the colors of the plugs on the cable with the
corresponding jacks on the DVD Player and the TV: yellow for video, red
for R (right) audio and white for L (left) audio.
14
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Analog signal
Audio (R)
Signal flow
Making Connections
Optional Video Connections
Visible improvements in DVD-Video quality can be achieved by making either S-video or component video connections to a TV or monitor
compatible with these types of connections.
Note
When either an S-video or component video connection is made, it is not necessary to make composite video connections using the yellow cord of the audio-video
cable.
Be sure to set TV Aspect after connection using the setup menu explained in “Customizing the Settings” starting on
page 30.
Making S-video connections
If the TV or monitor has an S-video input, making this type of video
connection will produce improved picture quality. Using an S-video
cable, connect the VIDEO OUTPUT S VIDEO jack to the
corresponding S-video input jack on the TV.
To S-video inputs
S-video cable
(not supplied)
VIDEO
OUTPUT
COMPONENT
DIGITAL
OUTPUT
OPTICAL
COAXIAL
ANALOG
OUTPUT
PR
DVD PLAYER
MODEL NO. DV-SP300
L
VIDEO
PB
R
S VIDEO
Y
Connect the power
cord after all
connections are
complete.
To component
video inputs
PR
PB
Y
Component video cable
(not supplied)
PR
Making component video connections
If the TV or monitor has component video inputs, making this type
of video connection will produce ideal picture quality for the
presentation of DVD-Video. Using a componect video cable (sold
separately), connect the VIDEO OUTPUT COMPONENT jacks to
the corresponding component video input jacks on the TV.
Actual labels for component video inputs may vary depending on
the TV manufacturer. (e.g., Y, R-Y, B-Y or Y, CB, CR)
In some TVs or monitors, the color levels of the playback picture
may be reduced slightly or the tint may change. In such a case,
adjust the TV or monitor for optimum performance.
PB
Component
signal
Y
S-video signal
Signal flow
To view Progressive scan video, you need a TV with Progressive
scan capability. Please check your TV’s manual.
Notes
• The DVD Player except North American models, outputs NTSC or PAL
format video depending on the format of the disc currently being played.
Make sure your TV supports the disc’s video format.
The North American models of this DVD Player output NTSC format
video only.
• Progressive scan only works with NTSC format discs.
15
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Making Connections
Optional Audio Connections
This DVD Player provides numerous ways to take full advantage of the digital multi-channel sound recorded on DVD and some CD media.
Be sure to set Digital Audio Out after connection using the setup menu explained in “Customizing the Settings” starting
on page 30.
Digital connections
Make digital connections from the DVD Player to an AV
component that features digital input capability or one or more
multi-channel audio decoders to realize the full cinematic
experience made possible by the DVD format. This DVD Player
features optical and coaxial digital audio output jacks and can
output Dolby Digital and DTS bitstreams as well as outputting
standard PCM.
Make connections from the DIGITAL OUTPUT OPTICAL jack to
the digital optical input jack on the AV component using an optical
fiber cable (sold separately). Make connections from the DIGITAL
OUTPUT COAXIAL jack to the digital coaxial input jack on the
AV component using a coaxial cable (supplied). It is not necessary
to make more than one type of digital connection to a single
component.
When you are making connections to an amplifier or receiver that
has internal Dolby Digital or DTS decoding capabilities, set Digital
Audio Out to “Dolby Digital” or “DTS” using the setup menu
explained in “Customizing the Settings” starting on page 30. See
page 35 for direct information.
When you are making connections to an amplifier or receiver that
has digital input capabilities, but no internal decoder, set Digital
Audio Out to “PCM” using the on-screen menu explained in
“Customizing the Settings” starting on page 30. See page 35 for
direct information. Setting Digital Audio Out to any other setting
could result in digital noise being output that could cause harm your
hearing and may also damage your speakers.
Notes
• Refer to the instructions supplied with the AV component for details on
what digital audio formats it is compatible with.
• Even if digital audio connections are made, it is also recommended to
make analog connections, because some conditions or media may prohibit
digital audio output.
Optical cable (not supplied)
Coaxial cable (supplied)
To digital input
(optical)
An amplifier or receiver with a
Dolby Digital or DTS decorder or
digital inputs
To digital input
(coaxial)
VIDEO
OUTPUT
COMPONENT
DIGITAL
OUTPUT
OPTICAL
COAXIAL
ANALOG
OUTPUT
PR
DVD PLAYER
MODEL NO. DV-SP300
L
VIDEO
PB
R
S VIDEO
Y
DO NOT connect the
power cord until all
connections are
complete.
To audio input
L
R
Making stereo audio connections
Using an audio cable (sold separately), make audio connections
from the ANALOG OUTPUT L and R jacks to the corresponding
jacks on the stereo component.
Be sure to set Digital Audio Out setting to “PCM” using the setup
menu explained in “Customizing the Settings” starting on page 30.
See page 35 for direct information.
An amplifier or receiver
with stereo inputs
Audio cable (not supplied)
Audio (L)
Analog signal
Audio (R)
Coaxial plug
Digital signal
Notes
• Be sure to match the colors of the plugs on the cable with the
corresponding jacks on the DVD Player and the stereo component: red for
R (right) audio and white for L (left) audio.
• Do not make connections to the PHONO or TUNER jacks on the stereo
component.
16
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Optical plug
Digital signal
Signal flow
Turning on
Connecting the POWER
The DV-SP300 is shipped with the main power (POWER) switch in the
on position ( ON). When the power cord is plugged in for the first
time, the DV-SP300 will automatically enter the standby mode and the
STANDBY indicator will light (same condition after step 2 below).
POWER
STANDBY/ON
Notes
• Make sure that all appropriate connections have been completed as
described on pages 14 to 16.
• Turning on the DVD Player may cause a momentary power surge,
which might interfere with other electrical equipment such as
computers. To prevent interference, use a wall outlet on a different
circuit.
STANDBY indicator
1
2
Plug the power cord into the
power outlet on the wall.
Press POWER to switch on
the main power.
STANDBY/ON
The DVD Player enters standby mode.
The STANDBY indicator lights up.
Notes
• The buttons on the remote controller do not operate if the POWER
switch is set to OFF.
• To switch off the main power, press POWER again.
3
Press STANDBY/ON on
the DVD Player or remote
controller.
The DVD Player turns on and the STANDBY indicator
turns off. It takes several seconds to read the disc in the disc
tray.
Notes
• You can turn on the DVD Player by pressing 0 or £/8.
• To put the DVD Player in the standby mode, press
STANDBY/ON on the DVD Player, or remote controller. Be
sure to set the volume to minimum before putting the DVD
Player in the standby mode for the next use to avoid sudden loud
sound reproduction.
• While the STANDBY indicator lights up, the DVD Player can
receive signals from the remote controller. However, if you press
POWER on the DVD Player to switch off the main power, the
remote controller cannot be used to turn on the DVD Player.
• Setting the STANDBY button to standby does not shut off the
power completely.
17
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
DVD
VCD
CD
Basic Playback
Before playing
• DVD-Video, Video CD, CD can be played with the DVD Player (see “Playable Discs” on page 6). Do
not play anything else.
• When playing DVD-Video or Video CD with video features, turn on the TV and set the TV to the DVD
Player's input.
• If an audio system is connected to the DVD Player, turn on the audio system and set it to the DVD
Player’s input.
About the
DVD
,
VCD
and
CD
If the DVD Player is connected to the TV or
amplifier through the analog audio jacks, do not
play DTS-encoded discs. Excessive noise may
be output from the analog stereo jacks, which
may damage the connected equipment.
To reproduce DTS surround sounds, digital
connection to an amplifier with a DTS decoder
is needed.
marks in the pages related to disc operation
DVD means the function or title is related to DVD-Video operation.
VCD means the function or title is related to Video CD operation.
CD
Warning
means the function or title is related to audio CD operation.
Starting Playback
STOP 7
0 OPEN/CLOSE
Disc tray
1
SKIP 4/¢
PLAY/PAUSE £/8
SEARCH 1/¡
■ To stop playback
Press 0 OPEN/CLOSE.
The disc tray opens.
If the DVD Player is in standby mode when the
0 OPEN/CLOSE button is pressed,
the DVD Player turns on and the disc tray opens. In this case,
it takes several seconds until the disc tray opens.
Press STOP 7.
When you press PLAY/PAUSE £/8 to restart playback,
playback starts from the location where you stopped playback
because the location index is stored in memory.
Note
The location where playback resumes may vary depending on the
disc or the scene where you stopped.
Playback from the beginning
2
Place a disc on the disc
tray.
Put the disc in the tray with the label side facing up.
There are two different disc sizes.
Place the disc in the correct guide on the disc tray.
3
Press STOP 7 again after stopping playback to clear the location
index memory, then press PLAY/PAUSE £/8 to start playback.
Tip to obtain a higher quality picture
Occasionally, some picture noise not usually visible during a normal
broadcast may appear on the TV screen while playing a DVD-Video
because the high resolution pictures on these discs include a lot of
information. While the amount of noise depends on the TV you use,
you should generally adjust the TV to reduce sharpness when viewing
DVD-Videos.
Press PLAY/PAUSE £/8.
The disc tray closes and playback starts.
If you press 0 OPEN/CLOSE to close the tray after
step 2, playback may automatically start.
The appropriate inserted disc indicator lights.
For the other information that appears in the display, see
page 12.
If the DVD Player is in standby mode when
PLAY/PAUSE £/8 is pressed,
the DVD Player turns on and playback starts. In this case, it
takes several seconds until playback starts.
18
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
CAUTION
Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
Basic Playback
Various Playback
■ To remove the disc
DVD
VCD
CD
Press 0 to open the disc tray.
Remove the disc after the disc tray opens completely.
After removing the disc, be sure to press the button again to
close the tray.
■ To play in fast reverse or fast forward
DVD
VCD
CD
OPEN/CLOSE 0
SLOW
DIMMER
STEP e/E
During normal playback, press 1/¡.
Each press of the same button changes the playback speed.
DOWN 4/UP ¢
(During DVD playback)
FR 1/FF ¡
F.SEARCH 1 (approx. x2) → F.SEARCH 2 (approx. x4) →
F.SEARCH 3 (approx. x8) → F.SEARCH 4 (approx. x16) →
F.SEARCH 1 (back to the beginning)
PLAY £
PAUSE 8
(During VCD/CD playback)
F.SEARCH 1 (approx. x2) → F.SEARCH 2 (approx. x4) →
F.SEARCH 3 (approx. x8) → F.SEARCH 1 (back to the beginning)
To resume normal playback, press £.
Notes
• The DVD Player mutes sounds and omits subtitles during fast
reverse and fast forward of DVD-Video and Video CD.
• The playback speed may differ depending on the disc.
■ To skip chapters or tracks
DVD
VCD
CD
During playback, press 4/¢.
The chapter (or track) in the direction of the button pressed is
skipped, and the selected chapter (or track) will be played
from the beginning.
When 4 is pressed once during playback, the chapter (or
track) being played will be played from the beginning.
RC-501DV
■ To pause playback (still mode)
DVD
VCD
CD
Press 8 during playback.
To start playback, press £.
■ Playing frame by frame
DVD
VCD
Press 28/83 repeatedly.
Each time you press the button the picture advances one frame.
To resume normal playback, press £ .
Notes
• The sound is muted during still mode and frame by frame playback.
• VCDs cannot be played frame by frame in reverse.
■ To play in slow-motion
DVD
Press DIMMER to change the display brightness.
Each time DIMMER is pressed, the display brightness of the
unit changes as shown below.
Normal → Dim Dark → More Dark → Normal
VCD
Press
/
during playback.
Each press of the same button changes the playback speed.
(During DVD playback)
F.SLOW / R.SLOW 1/16 → 1/8 → 1/4 → 1/2 → 1/16 (back to the
beginning)
(During VCD playback)
F.SLOW 1/8 → 1/4 → 1/2 → 1/8 (back to the beginning)
To resume normal playback, press £.
Notes
• The sound is muted during slow-motion playback.
• The playback speed may differ depending on the disc.
• R.SLOW is not available for Video CD.
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
■ Using DIMMER function
Notes
• Do not move the DVD Player during playback. Doing so may damage
the disc.
• Use 0 on the remote controller or DVD Player to open and close the disc
tray. Do not touch the disc tray while it is moving. Doing so may cause
the DVD Player to malfunction.
• Do not press down on the disc tray or put any objects other than playable
discs on the disc tray. Doing so may cause the DVD Player to
malfunction.
• In many instances, a menu screen appears when playback of a DVD
movie is complete. Prolonged display of an on-screen menu may damage
your television set, permanently etching that image onto its screen. To
avoid this, be sure to press 7 once the movie is complete.
19
DVD
VCD
CD
Using Banner Display
DVD
VCD
CD
Using the on-screen Banner Display
The on-screen Banner Display contains many playback features.
To see the Banner Display, press ON SCREEN on the remote
conroller while a disc is playing. Use 2/3 to move through the
different features in the Banner Display. Each feature is illustrated
with an icon.
1
During playback, press ON
SCREEN.
The Banner Display appears on the screen.
When playing a DVD
Chapter
Title
Subtitles
Audio
Bookmarks
Angles
Disc Type
ON SCREEN
SUBTITLE ON/OFF
SUBTITLE
Time Indicator
When playing a Video CD/CD
Introscan
Track
2/3/5/∞
ENTER
Time Information
Bookmarks
Disc Type
AUDIO
Time Indicator
CLEAR
2
Press 2/3 to select a desired item,
and press ENTER.
Corresponding menu appears on the screen.
«
To turn off the Banner Display
Press ON SCREEN or CLEAR.
Notes
• You can only access the banner display when you’re playing a disc.
• The banner display features are only available if the disc was created
with that particular feature (i.e., if you select the Subtitle icon, you won’t
be able to change the subtitle language unless the author of the disc
created the disc with subtitles).
• The invalid symbol
appears on the screen when you press a button
that doesn’t have any function. If one of the icons is “glayed out,” the
banner feature isn’t available for the disc you’re playing.
• Depending on the disc, pressing AUDIO or SUBTITLE may display a
disc menu. For more details, refer to the instruction notes on the disc.
20
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
RC-501DV
Using Banner Display
DVD
DVD
Selecting a Title
VCD
CD
Selecting a Chapter or Track
DVD-Video
DVD-Video
Title 1
Title 1
Title 2
Chapter 1
Some discs contain more than one title. For example, there might
be four movies on one disc (each movie might be considered a
title).
1
2
Title 2
Chapter 2
Chapter 1
Chapter 2
Chapter 3
Track 2
Track 3
Track 4
Track 5
Video CD/CD
Track 1
Press ON SCREEN.
Press 2/3 until the TITLE icon is
highlighted.
3
Press ENTER.
4
Press the numeric buttons to enter
the title number.
“T--” appears.
When you enter a one-digit title number, you
may have to press ENTER on the remote
controller after pressing the number (1~9) on
the remote controller. Otherwise press 0 first
and the other value. Then play starts. This
varies depending on number of title within the
disc you’re playing.
Because DVD discs use digital technology, a title can be divided
into individual chapters (similar to tracks on a CD). You can skip a
specific chapter by using the Chapter section in the Banner
Display.
1
Press ON SCREEN.
2
Press 2/3 until the CHAPTER or
TRACK icon is highlighted.
3
Press ENTER.
4
Press the numeric buttons to enter
the chapter or track number.
“C--” or “Tr.--” appears.
When you enter a one-digit chapter or track
number, you may have to press ENTER on
the remote controller after pressing the
number (1~9) on the remote controller.
Otherwise press 0 first and the other value.
Then play starts. This varies depending on
number of chapter or track within the disc
you’re playing.
Notes
• Some discs only have one title.
• The invalid symbol
appears on the screen when the disc doesn’t have
the function.
Notes
• The chapter feature won’t work if the disc isn’t formatted with separate
chapters.
• The invalid symbol
appears on the screen when the disc doesn’t have
the function.
21
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Using Banner Display
DVD
DVD
Selecting a Playback Audio Setting
Good morning!
Bon jour!
Changing the Subtitle Language
¡Buenos días!
Good evening!
You can select the preferred audio language and sound system as a
set from those included on the disc. This function lets you
temporarily change the audio language which you selected as the
automatic setting in the setting menu (see pages 30 and 31), and
choose the sound system if the disc is recorded in more than one
sound format.
1
Press On SCREEN during playback.
2
Press 2/3 until the AUDIO icon is
highlighted.
Bon soir!
¡Buenas tardes!
You can display subtitles on the TV screen and select a subtitle
language from those included on the DVD-Video.
1
Press On SCREEN during playback.
2
Press 2/3 until the SUBTITLE icon
is highlighted.
3
Press ENTER.
The subtitle menu appears.
Displayed when
SUBTITLE is on
3
Press ENTER.
The audio menu appears.
4
4
Press ENTER to select the subtitle
language.
Each time you press ENTER, the subtitle
language changes.
Press ENTER to select the audio.
Each time you press ENTER, the audio
recording system set changes.
5
Press SUBTITLE ON/OFF to select
subtitle on or off.
Switching between display of subtitles and no
display of subtitle is done each time the key is
pressed.
To turn off the audio menu
Press ON SCREEN or CLEAR.
The menu is switched off when no operation is performed for about
5 seconds.
Using AUDIO on the remote controller
1 Press AUDIO on the remote controller during playback.
2 Press AUDIO or ENTER to select the audio language.
Notes
• Dolby Digital 5.1 Channel sound may be displayed as “6ch. Dolby
Digital”.
• Before changing the setting, read through the explanation on “Digital
Audio Out” on page 35 and carefully select the setting.
• Depending on the disc, it may be necessary to select the audio sound
track using the DVD menu. When this is the case, press MENU to open
the DVD menu and select the appropriate sound track as indicated on the
DVD menu screen.
• When the DVD Player is turned on or when the disc is changed, the
audio settings are restored to the presets. In some cases, a language
recorded on the disc may be given priority and selected automatically
when the disc is loaded regardless of the setting.
• The invalid symbol
appears on the screen when the disc doesn’t have
the function.
22
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
To turn off the subtitle menu
Press ON SCREEN or CLEAR.
The menu is switched off when no operation is performed for about
5 seconds.
Using SUBTITLE on the remote controller
1 Press SUBTITLE on the remote controller during playback.
2 Press SUBTITLE or ENTER to select the subtitle language.
3 Press SUBTITLE ON/OFF to select sub title on or off.
Notes
• When you turn on the DVD Player or replace a disc, the DVD Player
returns to the automatic setting in the setting menu (see pages 30 and
31).
When you select a subtitle language which is not included on the disc,
the DVD Player plays the prior language programmed on the disc.
• During some scenes, the subtitles may not appear immediately after you
change the subtitle setting.
• Some DVD-Video are set to display subtitles automatically, and you
cannot turn them off even if you set the subtitle function to off.
• The invalid symbol
appears on the screen when the disc doesn’t have
the function.
Using Banner Display
VCD
DVD
Changing the Camera Angle
Angle : 1
Angle : 2
Angle : 3
If the scene was recorded from multiple angles, you can easily
change the camera angle of the scene you are watching.
1
Press On SCREEN during playback.
CD
Using IntroScan Function
Track : 1
Track : 2
Track : 3
IntroScan plays the first 10 seconds of each track on the Video CD
or CD similar to the scan feature that's on many car radios.
1
When playing a Video CD, press ON
SCREEN to display the Banner
Display.
When playing a CD, the Banner Display
appears on the screen automatically.
2
Press 2/3 until the Angle icon is
highlighted.
3
2
Press 2/3 until the IntroScan icon
is highlighted.
3
Press ENTER.
Press ENTER.
The angle menu appears.
4
Press ENTER to select the angle.
Each time you press ENTER, the angle
changes.
The INTRO indicator lights. The first 10
seconds of each track will be played.
Press £ to stop IntroScan playback and start
playing the current track entirely.
Notes
To turn off the angle menu
• After IntroScan goes through all of the tracks, it stops.
• The invalid symbol
appears on the screen when the disc doesn’t have
the function.
Press ON SCREEN or CLEAR.
The menu is switched off when no operation is performed for about
5 seconds.
Notes
• You can change the camera angle during still playback. The camera angle
changes to the new setting when you resume normal playback.
• If you pause a picture immediately after changing the camera angle, the
resumed playback picture may not use the new camera angle.
• The invalid symbol
appears on the screen when the disc doesn’t have
the function.
23
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Using Banner Display
DVD
VCD
CD
To clear the bookmark
Using a Bookmark
The bookmark is cleared when a disc is removed from the player,
when the power is turned off or when the player enters the standby
mode.
Notes
The bookmark feature lets you mark a point on the disc that you can
go to quickly. You can store up to 9 bookmarks.
• If all 9 bookmarks are in use, you can still mark new scenes, but the
previous bookmarks will be erased.
• Depending on the disc, the bookmark function may not work.
Marking a scene
Recalling a bookmarked scene
1
Press ON SCREEN during
playback.
1
Press ON SCREEN during
playback.
2
Press 2/3 until the bookmark icon
is highlighted and press ENTER.
2
Press 2/3 until the bookmark icon
is highlighted and press ENTER.
The bookmark menu appears.
The bookmark menu appears.
Exit Icon
«
«
3
Press ∞ to move the cursor to the
“Mark” parts of the bookmark
menu.
4
Press 2/3 to select the number
you want to mark on.
5
When you reack the scene you
want to mark, press ENTER.
3
Press 5 to move the cursor to the
“GO TO” parts of the bookmark
menu.
4
Press 2/3 to select the
bookmarked scene you want to
activate.
5
Press ENTER to activate the
bookmark.
The bookmark appears.
You can store up to 9 bookmarks by repeating
this step.
To return to the Banner Display
To turn off the bookmark menu
Press ON SCREEN or CLEAR.
Press 2/3 to select the exit icon and press ENTER.
Note
• The invalid symbol
the function.
24
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
appears on the screen when the disc doesn’t have
DVD
VCD
CD
Other Operations
The following operations can be performed directly from the
remote controller.
• Progressive Scan Function
• Random Play
• Repeat Play
• A-B Repeat Play
• Memory Edit Play
VCD
CD
Random Play
The chapters or tracks of the disc are played in random order.
Press RANDOM.
The random playback starts.
RANDOM
Display
REPEAT
Lights
RANDOM
A-B
ON SCREEN
The Random Play display appears on the
screen.
2/3/5/∞
ENTER
P. SCAN
To turn off the Random Play display
Press ON SCREEN or CLEAR.
The menu is switched off when no operation is performed for
about 5 seconds.
Numeric
buttons
To cancel random play
CLEAR
MEMORY
RC-501DV
Press RANDOM so that RANDOM indicator goes off or to select
“Standard Play”.
Each time you press RANDOM, random play will be on and off.
Random Play ↔ Standard Play
The Standard Play display appears when random is off.
DVD
VCD
Progressive Scan Function (NTSC Video
Output Only)
Notes
Progressive Scan function operates only when using NTSC format
disc.
1
Press P. SCAN to display
Progressive or Interlaced icon on
TV.
2
Press P. SCAN again while
displayed to switch between
Progressive and Interlaced.
• You cannot play DVDs in random order.
• When playing a PBC-compatible Video CD and PBC is on, you cannot
play it in random order. To use random play, press TOP MENU and
select “PBC off”, then press RANDOM.
Notes
• When component video is connected, you can use Progressive scan. If
S-Video or Composite video is connected, Progressive scan is not
available.
• If you connect a TV that is not compatible with a progressive scan signal
and choose “Progressive”, the picture may be distorted. With your TV
connected using either the Composite or S-Video terminals, choose
“Interlaced”.
• Progressive Scan only works with NTSC format disc.
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
25
Other operations
DVD
VCD
DVD
CD
Repeat Play
VCD
CD
A-B Repeat Play
A
Desired disc or title can be played back repeatedly.
There are four repeat options:
• Disc
Repeat the disc that is playing.
• Title
Repeat the title that is playing.
• Chapter Repeat the chapter that is playing.
• Track
Repeat the track that is playing.
B
The A-B repeat function lets you mark a segment to repeat between
the beginning “A” and the end “B” of the segment you want to
replay.
Press A-B when you want to
choose a scene (sound) as the
beginning point.
1
Press REPEAT repeatedly during
playback.
Display
Lights
REPEAT
The Repeat display appears on the screen.
Each time you press REPEAT, the repeat
option changes.
A-
The Repeat A- display appears on the screen.
At the time of DVD playback
→ Repeat Disc
↓
Repeat Title
↓
Repeat Chapter
↓
Repeat Off
Repeats the entire disc.
Repeats the current title.
2
Press A-B again to choose a scene
(sound) as the end point.
Repeats the current chapter.
The Bh ea t A-B display appears.
Resumes normal playback.
Display
At the time of Video CD/CD playback
→ Repeat Disc
↓
Repeat Track
↓
Repeat Off
Lights
REPEAT
A-B
Repeats the entire disc.
Repeats the current track.
Resumes normal playback.
The DVD Player automatically returns to
point A and starts repeat playback of the
selected segment (A-B).
Notes
• When playing a PBC-compatible Video CD and PBC is on, you cannot
play it repeatedly. To use repeat play, press TOP MENU and select
“PBC off”, then press REPEAT.
• With some DVDs, repeat playback may not be possible.
To turn off the Repeat display
Press ON SCREEN or CLEAR.
The menu is switched off when no operation is performed for about
5 seconds.
To cancel repeat play
Press REPEAT so that REPEAT indicator goes off or to select
“Repeat Off”.
Notes
• Repeat A-B will not function for segments under 3 seconds.
• When playing a PBC-compatible Video CD and PBC is on, you cannot
use A-B repeat function. To use A-B repeat function, press TOP MENU
and select “PBC off”, then press A-B.
To turn off the Repeat A-B display
Press ON SCREEN or CLEAR.
The menu is switched off when no operation is performed for about
5 seconds.
To cancel A-B Repeat play
Press A-B so that REPEAT and A-B indicators goes off or to
select “Repeat off”.
26
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Other operations
DVD
VCD
To delete memory
CD
Memory Edit Play
Title : 2
Chapter : 25
Title : 2
Chapter : 12
Title : 1
Chapter : 1
The DVD Player automatically plays titles, chapters, or tracks in
the order you program.
1
Press MEMORY during stop mode.
1 Press MEMORY during stop mode.
2 Move the cursor with 3 to the “Playlist” and press 5/∞ to select
the column to be deleted from the “Playlist”. (The color of the
column where the cursor is located will change.)
3 Press 2 and press 5/∞ to move the cursor to the Delete button
on the screen, and press ENTER.
Insert chapter or track
1 Press MEMORY during stop mode.
The MEMORY EDIT display appears.
The MEMORY EDIT display appears and the
MEM. indicator lights.
2
Press 5/∞ or numeric buttons to
select specific title/chapter or
track.
3
Press ENTER or 2/3.
2 Press 5/∞ or numeric buttons to select specific title/chapter or
track.
3 Move the cursor with 3 to the “Playlist” and press 5/∞ to
select the place you want to insert.
The color of the column where the cursor is located will change.
4 Follow the procedure on the left to select the desired chapter or
track.
5 Select the Insert button on the screen and press ENTER.
The new chapter or track will be inserted before (above) the
selected column.
To cancel memory play
Press MEMORY or 7 twice so that MEM. indicator goes off.
To clear memory
The memory is cleared when a disc is removed from the player,
when the power is turned off, or when the player enters the standby
mode.
Notes
4
Select Add button on the screen to
register selected value onto
Playlist, then press ENTER.
5
You can select a maximum of 32
values by repeating steps 2-4.
6
Press £ or select Play button on
the screen and press ENTER to
start playback.
• When you don’t add values onto Playlist and return to play mode, select
Done button and press ENTER on the remote controller.
• While a disc is playing, press MEMORY on the remote controller to start
memory play.
27
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
MP3 Function
MP3 On-screen Display
Playing Back MP3
The DVD Player can play back MP3 files recorded on CD-R or
CD-RW.
Folders within a root
Playback
information
Playing file
name
Track
Press £.
Time elapsed
When you insert MP3 media, playback will
start automatically.
MP3 On-screen display appears.
Note
Root icon
Folder icon
ALL CLEAR button
• %/fi indicates the content continues above or below the display.
To stop playback
To display files within a folder
Press 7.
Press 5/∞ to select the folder and press ENTER. The files within
the folder display will appear.
Files within a folder and memory window
To skip files
Press 4/¢ during playback.
Notes
Return folder icon
• It is not possible to play back folders and files that exceed the
maximum limitations of the media (up to 223).
• A certain amount of time is required for the player to confirm the
media on which MP3 files have been recorded before playback will
commence.
• The files will be played back in the sequence in which they were
recorded (written).
• Fast reverse and Fast forward do not function when playing MP3.
• Random function is not available for MP3.
Selecting MP3 Files
You can select the files to be played back directly.
Files
Memory window
1
Press 5/∞ to select the folder, then
press ENTER.
To move to the upper layer
Press 5/∞ to select the return folder icon (
) or press
RETURN, then press ENTER to return to the upper layer.
Note
• Single-byte characters between A and Z, single-byte numerais between 0
and 9, and the single-byte underscore (_) can be displayed.
28
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
«
MP3 Function
2
Press 5/∞ to select the file, then
press ENTER.
«
MP3 Memory Play
You can listen to the files in any desired order.
1
During stop mode, press MEMORY.
2
Press 5/∞ to select the file, then
press ENTER.
Playback will start from selected file.
Files in the next folder will be played back
when no files exist in the selected folder.
«
To select the folders to be played directly
1 During stop mode, press 5/∞ to select the folder, then press
ENTER.
2 Press 5/∞ to select the upper folder icon, then press £.
Playback will start from selected folder.
Files in the next folder will be played back when no file exist in
the selected folder.
The selected file goes to memory window.
You can select maximum 1025.
3
Press £.
MP3 Repeat Play
You can listen to the desired files repeatedly.
Press REPEAT repeatedly during
playback.
Each time you press the button, playback
information changes.
Repeat Disc
Repeats the entire disc.
Repeat 1 Folder
Repeats the current folder.
Repeat Track
Repeats the current track.
Standard Play
Resumes normal playback.
To cancel memory play
Press MEMORY or 7 so that MEM. indicator goes off or select
“Standard Play”.
To delete memory
During stop mode, press 2/3 to select the ALL CLEAR button,
then press ENTER.
You can delete file one by one by selecting and pressing CLEAR.
Note
• The memory is cleared when a disc is removed from the player, when the
power is turned off, or when the player enters the standby mode.
To cancel repeat play
Press REPEAT or 7 so that REPEAT indicator goes off or select
“Standard Play”.
Notes
• There is no A-B Repeat play function for MP3.
• You cannot use repeat playback for files programmed into memory.
29
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
DVD
VCD
CD
Customizing the Settings
When you insert a DVD-Video, Video CD, or CD, the various
functions of the DVD Player will be set (reset) according to the
setting menu.
You can customize this setting menu according to your preferences.
DVD
VCD
CD
Making Adjustments to Setting
1
Press MENU during stop mode.
Current setup menu display appears.
MENU
2
Press 5/∞ to select the item you
want to change, then press ENTER.
2/3/5/∞
ENTER
RETURN
«
Numeric
buttons
CLEAR
3
Press 5/∞ to change the setting,
then press ENTER.
RC-501DV
Further steps may be needed depending on the
item or setting. Follow the steps described in
the explanation of each item starting from
page 31.
«
4
5
Repeat steps 2 to 3 to change the
setting of other items.
Press MENU to turn off the setup
menu display.
30
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
How to use RETURN
When RETURN is presseed, the display returns to the previous
screen (stop mode).
Customizing the Settings
Language-related settings
Language Setting
Audio Language
DVD
This sets the language to be used when playing a disc. If a disc
does not contain the selected language, it is played in the priority
language set for each disc.
English:
Spanish:
French:
German:
Italian:
Others:
To display subtitles in English.
To display subtitles in Spanish.
To display subtitles in French.
To display subtitles in German.
To display subtitles in Italian.
To make a further choice. Follow steps 1 - 3 below.
1
Select “Other” and press ENTER.
2
Press the numeric buttons to enter the 4-digit code listed on page
36.
3
Select OK button and press ENTER.
Notes
English:
Spanish
French:
German:
Italian:
Others:
• Some DVD-Video may be set to display subtitles in a different language
than you selected. A prior subtitle language may be programmed on the
disc.
• Some DVD-Video allow you to change subtitle selections only via the disc
menu. If this is the case, press TOP MENU or MENU and choose the
appropriate subtitle language from the selection on the disc menu.
• Instruction notes of discs may refer to the button that displays the top menu
as title button.
To play sound tracks in English.
To play sound tracks in Spanish.
To play sound tracks in French.
To play sound tracks in German.
To play sound tracks in Italian.
To make a further choice. Follow steps 1 - 3 below.
1
Select “Other” and press ENTER.
2
Press the numeric buttons to enter the 4-digit code listed on
page 36.
3
Select OK button and press ENTER.
Menu Language
DVD
This sets the initial setup of language as well as the language used
in on-screen messages such as “PLAY”.
Note
Depending on the disc, a language recorded on the disc may be given priority
and selected automatically when the disc is loaded regardless of the setting.
Subtitle Language
DVD
This sets the language to be used when playing a disc. If a disc
does not contain the selected language, it is played in the priority
language set for each disc.
English:
Spanish:
French:
German:
Italian:
To display disc menus in English.
To display disc menus in Spanish.
To display disc menus in French.
To display disc menus in German.
To display disc menus in Italian.
Note
Some DVD-Video may not include your pre-selected language. In this case,
the DVD Player automatically displays disc menus consistent with the disc’s
initial language setting.
31
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Customizing the Settings
General utility settings
Operation Setting
Rating / Parental Lock
DVD
This can restrict playback of adult-oriented DVD discs that you do
not want to be seen by children.
To input password
1
Select “Set Password”.
2
Press the numeric buttons to enter password.
3
Select OK button and press ENTER.
Confirm Password display appears below Enter Password
display.
4
Press the numeric buttons to enter password.
5
Select OK button and press ENTER.
However, even when a DVD disc is marked “Adult-oriented” or
otherwise on the label, its viewing cannot be restricted unless the
restriction level is recorded in the disc itself.
You cannot play DVD Video rated higher than the level you selected unless
you cancel the parental lock function.
For example, when you select level 7, discs rated higher than level 7 are
locked out and cannot be played.
The Rating level is equivalent to the following U.S. movie ratings.
Level 7: NC-17
Level 6: R
Level 4: PG-13
Level 3: PG
Level 1: G
Notes
• DVD-Video may or may not respond to the parental lock setting. This is not a
defect in the DVD Player. Make sure this function works with your DVD-Video.
• When the password already has been set, the screen for change of the
entered password will be displayed. In that case, enter the password (See
“Password” below).
Password
DVD
The password for rating setting, change, cancellation, etc. is set.
Note
Be sure not to forget your password. If you should forget it, press
STANDBY/ON and 4 on the unit simultaneously to clear the password.
If the display on the unit disappears with this operation, press the POWER
switch on the unit and then press it again to recover the display.
32
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Customizing the Settings
Operation Setting (continued)
To change password
6
Press the numeric buttons to enter new password.
1
Press the numeric buttons to enter password.
7
Select OK button and press ENTER.
2
Select OK button and press ENTER.
Password setup menu appears.
To clear password
3
Select “Change Password”.
Enter Password menu appears.
4
Press the numeric buttons to enter new password.
5
Select OK button and press ENTER.
Confirm Password display appears below Enter Password
display.
1
Press the numeric buttons to enter password.
2
Select OK button and press ENTER.
Password setup menu appears.
3
Select “Clear Password” and press ENTER.
33
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Customizing the Settings
Audio output setting
Picture-related setting
Picture Setting
Audio Setting
TV Aspect
DVD
This sets the screen size (4:3 or 16:9 aspect ratio) according to the
connected TV.
4 x 3 Letterbox:
Choose this setting if you would
prefer to see movies in their
original aspect ratio. You will see
the entire frame of the movie, but
it will occupy a smaller portion
of the screen. This setting may
result in the movie appearing
with black bars at the top and
bottom of the screen.
4 x 3 Pan Scan:
Choose this setting if you want
the movie to fill the entire screen
of your TV. You won’t see part of
the picture (particularly the right
and left edge).
Some disc produced in a wide
screen format can’t be cropped in
this fashion, which means the
black bars would appear at the
top and bottom of the screen.
16 x 9 Widescreen:
Choose this setting if your DVD
Player is connected to a
widescreen TV.
Notes
34
• The displayable picture size is preset on each DVD-Video. Therefore, the
playback picture of some DVD-Video may not conform to the picture size
you select.
• When you play a DVD-Video recorded in the 4:3 picture size only, the
playback picture always appears in the 4:3 picture size regardless of the TV
shape setting.
• If you select “16:9 Widescreen” and you own a 4:3 TV set, the DVD
playback picture will be horizontally distorted during playback. Images
will appear to be horizontally compressed. Make sure the TV Shape
conforms to the actual TV in use.
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Dynamic Range
DVD
Dynamic Range setting allows you to “compress” the dynamic
range of a DVD’s sound track, so that you can lower the volume
without losing extremely soft signals. This is especially useful
when you are watching a movie late at night.
Off:
On:
Full dynamic range is maintained.
Dynamic range is reduced.
Notes
• This function works only during playback of Dolby Digital recorded discs.
• The level of Dynamic Range Reduction may differ depending on the DVD.
Customizing the Settings
Audio Setting (continued)
Digital Audio Out
DVD
VCD
CD
DOLBY DIGITAL Surround
DVD Video that have the
This sets the type of audio output from the digital audio output jack.
D I G I T A L
mark are recorded using this system.
DTS Surround
DVD Video and CD that have the
mark are recorded using this system.
Important: DTS information
If you set the Digital Audio Out setting to DTS, you must have your DVD
Player connected to a receiver or decoder with the DTS feature and the disc
you play must support the DTS audio format. If you choose DTS and your
receiver, decoder or disc doesn’t support DTS, you won’t hear any audio
when you play the disc.
Linear PCM
DVD
VCD
CD
PCM:
Select when connected to a 2 channel digital stereo
amplifier (see page 16).
The DVD Player outputs sounds in the PCM format
when you play a DVD-Video disc recorded on the
Dolby Digital.
The DVD Player does not output sounds in the
PCM format when you play a DVD-Video disc
recorded on the DTS recording system.
Dolby Digital: Select when you connected to an amplifier equipped
with a Dolby Digital decorder (see page 16).
The DVD Player outputs digital audio information
in the Dolby Digital format when you play a DVDVideo recorded in the Dolby Digital recording
system.
The DVD Player does not output sounds in the
PCM format when you play a DVD-Video disc
recorded on the DTS recording system.
DTS:
Select when you connected to an amplifier equipped
with a DTS decorder (see page 16).
The DVD Player outputs digital audio information
in the DTS format when you play a DVD-Video
recorded in the DTS recording system.
The DVD Player outputs sounds in the Dolby
Digital format when you play a DVD-Video disc
recorded on the Dolby Digital recording system.
96KHz ⇒ 48KHz:
96KHz ⇒ 96KHz:
Even in case of 96 kHz digital signal, the
DVD Player will deliver 48 kHz signal out.
In case of 96 kHz digital signal, the DVD
Player will deliver 96 kHz signal out. In this
case, your receiver should control 96 kHz
signal.
Dolby Digital and DTS
The 5.1-channel digital surround format of DOLBY DIGITAL/DTS enables
you to individually play five full-range (20 Hz-20 kHz) channels (left and
right front, center, two surround channels) plus an LFE (Low Frequency
Effect) channel for the low-range effect sound. It will create a realistic sound
as heard in theaters and concert halls.
35
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Table of Languages
Table of Languages and Their Code No.
Code No.
6566
6565
6570
8381
6577
6582
7289
6583
6588
6590
6665
6985
6678
6890
6672
6673
6682
6671
7789
6669
7577
6765
9072
6779
7282
6783
6865
7876
6978
6979
6984
7079
7074
7073
7082
7089
7176
7565
6869
6976
7576
7178
7185
7265
7387
7273
Language
Abkhazian
Afar
Afrikaans
Albanian
Ameharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali; Bangla
Bhutani
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Danish
Dutch
English
Esperanto
Estonian
Faroese
Fiji
Finnish
French
Frisian
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
36
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Code No.
7285
7383
7378
7365
7369
7375
7165
7384
7465
7487
7578
7583
7575
8287
7589
8278
7579
7585
7679
7665
7686
7678
7684
7775
7771
7783
7776
7784
7773
7782
7779
7778
7865
7869
7879
7967
7982
7977
8065
8083
7065
8076
8084
8185
8277
8279
Language
Hungarian
Icelandic
Indonesian
Interlingua
Interlingue
Iunpiak
Irish
Italian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean
Kurdish
Laothian
Latin
Latvian, Lettish
Lingala
Lithuanian
Macedonian
Malagsy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Naru
Nepali
Norwegian
Occitan
Oriya
Oromo (Afan)
Panjabi
Pashto, Pushto
Persian
Polish
Portuguese
Quechua
Rhaero-Romance
Romanian
Code No.
8285
8377
8371
8365
7168
8382
8372
8384
8478
8378
8368
8373
8383
8375
8376
8379
6983
8385
8387
8386
8476
8471
8465
8484
8469
8472
6679
8473
8479
8483
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
Language
Russian
Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Servo-Groatian
Sesotho
Setswana
Shona
Sindhi
Singhalese
Siswati
Slovak
Slovenian
Somali
Spanish
Sundanese
Swahili
Swedish
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Troubleshooting
Check the following guide for the possible cause of a problem before contacting service. Refer also to the respective instruction manuals of the
connected components and TV.
Symptoms
Causes
Remedies
Pages
The DVD Player doesn’t
switch on.
• The power cord is disconnected.
• The main power is set to OFF.
• There is external noise in the computer
circuits of the DVD Player.
• Check the connection of the power cord.
• Turn on the main power.
• Switch off the main power, then switch it on
again. If not recovered, disconnect the power
cord, then connect it again.
• Contact your nearest Onkyo service center.
17
17
17
The DVD Player doesn’t start
playback.
• No disc is inserted.
• Insert a disc. (Check that “DVD,” “VCD,” or
“CD” is lit in the DVD Player’s display).
• See “1. Regional Restriction Codes (Region
Number)” on page 4.
• Check the playable discs.
• Place the disc with the playback side down.
• Place the disc within the proper guide on the
disc tray.
• Eject the disc and clean it.
• Deactivate the parental lock function or
change the parental lock level.
18
• Connect the DVD Player directly to the TV.
Avoid connecting the DVD Player to the TV
through a VCR.
• Press P.SCAN on the remote controller and
select Interlaced icon.
14
• The AC fuse is blown.
DVD Player
• The region number of the disc does not match
that of the DVD Player.
• An unplayable disc is inserted.
• The disc is placed upside down.
• The disc is not placed within the disc tray
guide.
• The disc is dirty.
• The parental lock function is activated.
Brightness is unstable or noise
is visible on the playback
picture.
• Copy protection is activated.
• The TV is not compatible with progressive
scan signal.
4
6
18
18
7
32
25
The playback picture is
occasionally distorted.
• The disc is dirty.
• It is in fast forward or fast reverse playback.
• Eject the disc and clean it.
• Sometimes a small amount of picture
distortion may appear. This is not a
malfunction.
7
–
Playback doesn’t follow the
course of the disc’s programs.
• The DVD Player is in repeat playback mode,
memory playback mode, or random playback
mode, etc.
• Resume normal playback.
18
The picture from the DVD
Player doesn’t appear on the
TV screen.
• The TV is not set to receive the output signals
from the DVD Player.
• The DVD Player is not properly connected.
• Set the TV to the DVD Player’s input.
–
• Check the connections to the DVD Player.
14, 15
No sound or inaccurate sound
is reproduced.
• A wrong sound signal conversion method
(Digital Audio Out) is selected.
• Check the current sound signal conversion
method, and select the right setting for
“Digital Audio Out”.
• Set the TV to the DVD Player’s input.
35
• Check the connections to the DVD Player.
14-16
• The TV is not set to receive the output signals
from the DVD Player.
• The DVD Player is not properly connected.
Remote Controller
–
–
The buttons on the remote
controller and DVD Player do
not operate.
• Power supply fluctuations or other
abnormalities such as static electricity may
interrupt correct operation.
• Switch off the main power, then switch it on
again. If not recovered, disconnect the power
cord, then connect it again.
17
The buttons on the DVD
Player operate but the buttons
on the remote controller do
not operate.
• No batteries are inserted in the remote
controller.
• The batteries are worn out.
• The remote controller is not pointed at the
remote sensor of the DVD Player.
• The remote controller is too far from the DVD
Player.
• Insert new batteries.
9
• Replace with new batteries.
• Point the remote controller at the remote
sensor of the DVD Player.
• Operate the remote controller within 5 m
(16 feet).
9
9
9
Because the unit contains a microcomputer to provide advanced functions, it may malfunction due to external noise or static electricity. If
this happens, press the POWER switch on the unit and then press it again after about five seconds.
37
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Specifications
DVD Player
Power supply
AC 120 V, 60 Hz (North America models)
AC 110-240 V, 50/60 Hz (Other models)
Power consumption
16 W
Weight
8.2 lbs
External dimensions
17 1/8" x 3 7/8" x 12 11/16" (W/H/D)
Signal system
NTSC (North America models)
PAL/NTSC (Other models)
Regional restriction code
(region number)
Region 1 (North America)
Region 4 (Central and South America and Australia)
Frequency range (digital audio)
(DVD linear sound)
48 kHz sampling 4 Hz to 22 kHz
96 kHz sampling 4 Hz to 44 kHz
Signal-to-noise ratio (digital audio)
More than 90 dB
Audio dynamic range (digital audio)
More than 95 dB
Harmonic distortion (digital audio)
Less than 0.005 %
Wow and flutter
Below measurable level
Operating conditions
Temperature: 5°C to 35°C (41°F to 95°F)
Operation status: Horizontal
Outputs
Video output
1.0 V (p-p), 75 Ω, negative sync., pin jack × 1
S-video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., Mini DIN 4-pin × 1
(C) 0.286 V (p-p), 75 Ω
Component video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., pin jack × 1
(PB)/(PR) 0.7 V (p-p), 75 Ω, pin jack × 2
Audio output (digital output Optical)
Optical connector × 1
Audio output (digital output Coaxial)
0.5 V (p-p), 75 Ω, pin jack × 1
Audio output (2-Channel Audio)
2.0 V (rms), 320 Ω, pin jack (L, R) × 1
Specifications and features are subject to change without notice.
38
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Memo
39
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8111 Fax: 072-833-5222
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 201-785-2600 Fax: 201-785-2650 http://www.onkyousa.com
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 E-mail: [email protected]
ONKYO CHINA LIMITED
Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
SN 29343344
Downloaded From DvDPlayer-Manual.com Onkyo Manuals
HOMEPAGE
http://www.onkyo.co.jp/
W0206-1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement