INSTRUCTION MANUAL

Super Sports Senior- 90

0.91 cubic inch displacement 4 - stroke (glow)

radio w/ 5 servos

Wing Span

Wing Area

Specifications

81 in / 2050mm

1020 sq in / 65.8 sq dm

Flying Length

Fuselage Length

9 lbs / 4100 g

61 in / 1560mm

* Specifications are subject to change without notice. *

Warning ! This model is not a toy.

It is designed for precision model. Please seek advice if one familiar this kind of engine powered precision model.

Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing.

Always keep this instruction manual at hand for quick reference.

FACTORY PRE-FABRICATED

ALMOST-READY-TO-FLY (ARF) SERIES

MADE IN CHINA

Super Sports Senior - 90

I N D E X

BEFORE YOU BEGIN

PARTS LIST

ASSEMBLY

SAFETY PRECAUTIONS

P. 1

P. 2

P. 3 -10

P. 10

BEFORE YOU BEGIN

1

2

3

Apply epoxy glue.

Assemble left and right sides the same way.

Peel off shaded portion covering film.

3mm

Drill holes with the specified diameter (here: 3mm).

Pay close attention here!

Pierce the shaded portion covering film.

P . 1

Apply instant glue

(C.A.glue, super glue.)

Ensure smooth non-binding movement while assembling.

Cut off shaded portion.

Must be purchased separately!

Do not overlook this symbol!

Parts List

1. MAIN WING -- 1 pair

2. SCREW PM2 X 20mm -- 2 pcs

SCREW PM2 X 25mm -- 4 pcs

PUSHER ROD Ø1.8 x 106mm w/ Threads (For Aileron) -- 2 pcs

TRI-HORN M3 X 14mm (L) -- 2 sets

CLEVIS -- 2 pcs

STRAPER -- 2 pcs

FUEL TUBE Ø6 X 5mm -- 4 pcs

3. MAIN LANDING GEAR -- 1 pair

MAIN LANDING GEAR COVER -- 1 set

MOUNTING PLATE 12 X 20mm -- 4 pcs

SCREW PA3 X 14mm -- 8 pcs

SCREW PM2 X 8mm -- 8 pcs

WASHER d2 X D5mm -- 16 pcs

M2 NUT -- 8 pcs

4. SCREW PA3 X 12mm -- 4 pcs

COLLAR Ø5.1mm w/ Set screw -- 4 sets

MAIN WHEEL Ø90mm -- 2 pcs

WHEEL PANTS -- 1 pair

MOUNTING PLATE 12 X 20mm -- 2pcs

5. WING TUBER Ø18 X 701mm -- 1 pc.

6. STABILIZER & ELEVATOR -- 1 set

SCREW PM3 X 25mm -- 1 pc.

WASHER d3 X D7mm -- 1 pc.

FUSELAGE -- 1 pc.

7. VERTICAL FIN & RUDDER -- 1 set

8. TAIL LANDING GEAR -- 1 set

TAIL WHEEL Ø25mm -- 1 pc.

SCREW PA3 X 12mm -- 2 pcs

COLLAR Ø2.1mm w/ Set screw -- 1 set

SCREW PM2 X 14mm -- 1 pc.

WASHER d2 X D5mm -- 2 pcs

M2 NUT -- 1 pc.

ALUMINUM PLATE 0.3mm -- 1 pc.

9. FUEL TANK 450CC -- 1 set

BALSA 8 x 10 x 116mm (For fixing fuel tank) -- 1 pc.

10. ENGINE MOUNT (PL5911120) -- 1 set

SOCKET HEAD SCREW M6 X 30mm -- 4 pcs

WASHER d6 X D15mm -- 4 pcs

11. THROTTLE PUSHWIRE Ø1.2 x 340mm

w/Plastic tube d2 x D3 x 185mm -- 1 set

ALUMINUM PLATE (For Engine Mount) – 1pc.

ANTI - VIBRATION MOUNT -- 1 set

INCLUDE: SCREW M4 X 35mm -- 4 pcs

SCREW KM3 X 20mm -- 8 pcs

WASHER d4 X D12mm -- 8 pcs

M3 NYLON INSERT LOCK NUT -- 8 pcs

M4 NYLON INSERT LOCK NUT -- 4 pcs

12. COWLING -- 1 set

TRANSPARENT DUMMY COWLING -- 1 set

PWA2.6 X 12mm -- 5 pcs

SILICON GROMMET d1.5 X D6.5mm -- 5 pcs

SPINNER Ø70mm -- 1 set

13. WIRE Ø1 x 900mm (For Rudder) -- 2 pcs

COPPER TUBE d2.5 X D3.2 X 8mm -- 2 pcs

RIGGING COUPLER Ø1.8 X 27mm w/ Threads (For Rudder) -- 2 pcs

SCREW PM2 X 16mm -- 3 pcs

M2 NUT -- 3 pcs

TRI-HORN M3 X 14mm (L) (w/ o - Base For Rudder) -- 2 sets

FUEL TUBE Ø6 X 5mm -- 2 pcs

CLEVIS -- 2 pcs

14. PUSHROD Ø1.8 x 660mm w/ Threads (For Elevator) -- 2 pcs

TRI-HORN M3 X 4mm (L) -- 2 sets

SCREW PM2 X 16mm -- 6 pcs

CLEVIS -- 2 pcs

FUEL TUBE Ø6 X 5mm -- 2 pcs

15. LINKAGE CONNECTOR Ø2.1mm -- 1 set

16. SPONGE 60 X 70 X 115mm -- 1 pc.

RIGGING Z BEND Ø1.8 x 27mm (For Rudder) -- 2 pcs

PUSHROD Ø1.8 x 170mm (For Elevator) -- 1 pc.

COPPER TUBE d2.5 X d3.2 X 8mm -- 2 pcs

STRAPER -- 1 pc.

FUEL TUBE Ø6 X 5mm -- 1 pc.

PLYWOOD 120 X 35 X 6mm (For Throttle Servo) -- 1 pc.

BALSA 6 x 6 x 35 (For Throttle Servo Stand) -- 2 pcs

PUSHROD CONNECTOR 8 X 9 X 20mm -- 1 set

17. CANOPY -- 1 set

SCREW PWA2.3 X 8mm -- 8 pcs

SILICON GROMMET d1.5 X 6.5mm -- 8 pcs

PILOT PL001085A/B -- 1 pc.

18. SCREW PM4 X 35mm -- 2 pcs

WASHER d4 X D15mm --2 pcs

PLYWOOD 2 x 30 x 120mm (Wing Protection) -- 1 pc.

19. DECALS -- 1 set

COVERING:

RED COLOR SCHEME:

TOUGHLON STL 312 BRIGHT RED

TOUGHLON STL 320 ORANGE

TOUGHLON STL 330 CADMIUM YELLOW

TOUGHLON STL 351 DARK BLUE

TOUGHLON STL 100 WHITE

PURPLE COLOR SCHEME:

TOUGHLON STL 351 DARK BLUE

TOUGHLON STL 360 VIOLET

TOUGHLON STL 361 PURPLE

TOUGHLON STL 241 TURQUOISE

TOUGHLON STL 100 WHITE

P. 2

1 Main Wing

Pre-glued

2 Aileron Servo

PM2 x 20mm Screw

2

PM2 x 25mm Screw

4

Pusher Rod

1.8 x 106mm

Ø1mm pilot holes for World Models tri-horn are pre-drilled.

Please look for pin-hole marks at under side of control surfaces.

Straper

PM2 x 20mm

PM2 x 25mm

Fuel Tube

6 x 5mm

Tri-horn

M3 x 14mm

Bottom View

3 Main Landing Gear

PA3 x 14mm Screw

8

PM2 x 8mm Screw

8 d2 x 5mm Washer

16

M2 Nut

8

PA3 x 14mm d x D5 mm Washer

PM2 x 8mm

Plate

M2 NUT

Bottom View

P. 3

4 Main Landing Gear

PA 3 x 12mm Screw

4

3mm Set Screw

4

5.1mm Collar

4

PA 3 x 12mm

3mm Set Screw

Completed

5.1mm Collar

Wheel 90mm

5 Main Wing

Peel off shaded portion covering film for lead to another aileron servo.

6 d3 x D7mm Washer

1

PM3 x 25mm Screw

1

PM3 x 25mm d3 x D7mm

Apply thread locker to screws.

Bottom View

Pre-glued

P. 4

Wing Tuber

Ø18 x 701mm

Peel off shaded portion covering film

Lead to aileron Servo.

7

A A'

A = A'

Pre-glued

8 Tail Landing Gear

PA 3 x 12mm Screw

2

3mm Set Screw

1

2.1mm Wheel Collar

1

1 d2 x D5mm Washer

2

M2 Nut

1 d2 x D5mm Washer

Washer 2mm

3mm Set Screw

PM2 x 14mm

2mm

PA3 x 12mm

9 Fuel Tank

Fuel Tank 450cc

Install Balsa 8 x 10 x 116mm

(For fixing fuel tank)

Fuel Tank

450cc

P. 5

10 Engine Mount

M6 x 30mm Socket Head Screw

4 d6 x D15mm Washer

4

Engine Mount

Pl5911120 d6 x D15mm

M6 x 30mm

Apply thread locker to screws.

Blind nuts are off-centered to keep the spinner at the fuselage axis.

11 Engine

M4x35mm SOCKET HEAD SCREW

4

KM3x20mm Screw

8

M4 Nylon Insert Lock Nut

4

M3 Nylon Insert Lock Nut

8 d4 x D12mm Washer

8

M4 Nylon

Insert Lock Nut d4 x D12mm

Washer

Plastic Tube d2 x D3 x 185mm

Throttle Push wire

1.2 x 340mm

KM3 x 20mm d4 x D12mm

Washer

Make sure the rounded edges are facing the shock absorbing

SILICON PAD.

3mm

M4x35mm

SOCKET HEAD SCREW

Illustration is for inverted mounting.

You can mount the engine upright

or sideways simply by rotation the

engine mount. Thrust angles will

not be affected.

Install Engine position

Spinner

70mm

142mm

5.6in.

P. 6

12 Cowling

PWA2.6 x 12mm Screw

5 d1.5 x D6.5mm Silicon Grommet

5

First insert the grommet to the cowling then apply screw.

Silicon Grommet

d1.5 x 6.5mm

Spinner

PWA2.6 x 12mm

13 Rudder Pullwire

PM2 x 16mm Screw

3

M2 Nut

3

Ø 1mm pilot holes for World Models tri-horn are pre-drilled.

Please look for pin-hole marks at side of control surfaces.

Wire Ø1 X 900mm

135m m

M2 Nut

Tri-horn

PM2 x 16mm

14 Elevator Pushrod

PM2 X 16mm Screw

6

Ø 1mm pilot holes for World Models tri-horn are pre-drilled.

Please look for pin-hole marks at under side of control surfaces.

235m m

PM2 X 16mm

Pushrod Ø1.8 X 660mm

w/Threads

Clevis

Fuel Tube

P. 7

15 Servo Set

LINKAGE CONNECTOR

3 x 3mm Set Screw

1

Linkage Connector

1

2mm Nut

1

2mm Washer

2

Throttle Rod

2mm

2mm

3mm

Included with the Radio Set.

Throttle Servo.

Please refer to attached sheet for linkage connector installation.

16 Radio Equipment

Install and arrange the servo as shown in the diagram.

Copper Tube

Press down the center

1/3 portion

Front Balsa 6 x 6 x 35mm Spong 60 X 70 X 115mm

Rudder Servo

Wire Ø1 X 900mm

Pushrod Connector

8 X 9 X 20mm

Plywood

35 x 6 x 120mm

Fuel Tube

Straper

Copper Tube

Throttle

Servo

Balsa 6 x 6 x 35mm Elevator Servo Pushrod 1.8 X 170mm

Rigging Z Bend

Ø 1.8 x 27mm

M2 Nut

Bottom View

Elevator Pushrod

Ø 1.8x170mm

Elevator Servo

Bottom View

P. 8

KM 2x8mm

17 Canopy

PWA2.3 x 8mm Screw

8 d1.5 x D6.5mm Silicon Grommet

8

First insert the grommet to the canopy then apply screw.

Pilot Silicon Grommet

d1.5 x 6.5mm

PWA2.3 x 8mm

18 Main Wing

PM4 x 35mm Screw

2 d4 x D15 Washer

2

PM4 x 35mm d4 x D15mm

4mm

19 Wing Setting

Bottom View

Adjust the wing and fuselage configuration as in the diagrams.

0

2.5

A A'

1.5

P. 9

A = A'

B = B'

C = C'

B B'

C C'

20 Control Throws

Elevator

Rudder

Aileron

20mm

20mm

44mm

44mm

Adjust the control throws as shown in the diagram. These throws are good for general flying. You can adjust according to your personal preference.

9mm

9mm

21 C.G

108mm

The ideal C.G. Position is 108mm (4.25 in) behind the leading edge measured at where the wing meets the fuselage. In order to obtain the C.G.

specified, add weight to the fuselage or move the battery position. Check the C.G. before flying.

Important Safety Precautions

First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary.

Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft.

Super Sports Senior - 90 is specially designed to be powered by 0.91 4 stroke glow engine, using a more powerful engine does not mean better performance. In fact, over powered engine may cause severe damage and injuries.

Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running propeller.

If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles. Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone. Too hot an iron may damage the covering.

Check and re-tighten up all factory assembled screws, use thread locker if applicable.

A119R0610 P. 10

ed

Fan

Pat ern

Funf y

Gl der

Boat

A119R0610

The World Models

Manufacturing Co., LTD.

w w w . t h e w o r l d m o d e l s . c o m