D.T.Systems Super Trainer EZT plus 5002 Owner`s manual

D.T.Systems Super Trainer EZT plus 5002 Owner`s manual
Electronic Dog Trainer
Owner’s Manual
2872 Walnut Hill Lane
Dallas, Texas 75229
Tel: (214) 350-9446, (888) LUV-U-DOG
Fax: (214) 350-7847
Website: http://www.dtsystems.com
E-mail: [email protected]
• EZT plus 5000
• EZT plus 5002
How the Limited Lifetime Warranty works:
• To qualify for the Warranty you must fill out the
warranty registration card which came with your
system and mail it (with your original sales receipt)
to D.T. Systems within 30 days of purchase.
• There is no charge for parts or labor for the first
year on any of our lifetime warranty products.
• When the product’s labor warranty expires after the
first year, there will be a normal labor charge for
any repair under the lifetime warranty program
should your system be in need of service. Labor
charges will range from $35 to $110 depending on:
1) the system model, and 2) the severity of the
repair needed.
• Any defective manufactured part or parts that need
replacement will be free during the lifetime warranty
Your EZT plus Super TrainerTM has been manufactured
under complete compliance with the Federal
Communication Commission (FCC). The complex internal
structure of each product has been designed to operate
within specific regulations of FCC specifications. Any
unauthorized modifications to your product is a violation of
these specifications.
The EZT plus Super TrainerTM has been made with State
of the Art equipment. Any fine adjustment should be
performed only by D.T. Systems’ technicians.
Table of Contents ..................................3
Package Contents .................................5
Model Features......................................6
Adjusting and Positioning
Your Collar for Proper Fit.......................7
Parts and Functions...............................8
Batteries ................................................13
Important Safety Notes..........................15
Maintenance ..........................................16
Warranty ................................................17
FCC Compliance ...................................18
Contact Information ...............................20
Congratulations and thank you for purchasing our
EZT plus 5000/5002 Super TrainerTM Beeper
Training Collar. The EZT series represents the
absolute latest technological advancement in the
Electronic Dog Training World. It offers MaxxRange™, the industry’s only internally woven
antenna in the collar. With up to a one mile range,
they are perfect for hunting, basic obedience and
professional training. EZT series collars feature
Sixteen levels of stimulation intensity, with an easy
‘no-look’ clicking intensity selection dial. Easy one
hand operation allows for maximum control and
safety. This model includes both Constant and
Momentary ‘Nick’ stimulation, and a beeper with
Locate, Run/Point and Point only modes. The
collars are 100% waterproof and can be worn even
when the dog is submerged. The EZT plus Series
Dog Training Collar is durable, safe and very
humane when used correctly. The automatic safety
shut-off feature stops the stimulus from both the
transmitter and the receiver to prevent accidental or
prolonged stimulation.
D.T. Systems Premium Lifetime Warranty is the best
warranty offered in the industry. This warranty is free
to participating U.S. customers.
(The warranty
registration card must be returned within 30 days of
original purchase). This changes our normal one year
parts and labor warranty to a lifetime warranty against
manufacturing defects on parts and a one year
warranty on labor.
What is covered:
D.T. Systems Premium Lifetime Warranty covers all
parts to be free from manufacturing defects for as long
as the unit is held by the original owner.
What is not covered:
• Batteries are not part of our lifetime warranty.
Rechargeable batteries are warranted against defects
for one year from the original purchase date.
• Our warranty does not cover parts that malfunction
due to abuse, misuse, improper maintenance, or
incorrect handling.
• Damage from dogs chewing or wear and tear from
excessive field use is not covered.
• Our warranty does not cover the cost of shipping
the unit to our repair center. Return ground shipping
(inside the continental United States) to the customer
is covered. However, next day or second day air
shipping is not covered, but available by request for an
extra shipping fee.
• It is very important to periodically clean your EZT
plus Super TrainerTM for maximum performance.
Regular cleaning will also lengthen the life of your
• Clean the EZT plus Super Trainer
collar box
with lukewarm water and a mild anti-bacterial soap.
• Take care to thoroughly clean the space between
the electrodes and the belt.
Collar Receiver (two for EZT plus 5002)
4” Antenna for the Transmitter
Rechargeable Batteries for both the Collar and
Battery Charger
Double Jack Cable for simultaneous charging
Test Light
Owner’s Manual
Carrying Case
• The belt and buckle should be cleaned with water
and a mild soap then allowed to dry completely.
• Always allow the entire unit to completely dry before
Please read this owner’s manual in its entirety
before operating this unit. Should you have any
questions about our collars or their operation
please contact our Customer Service department
(see back page for address and phone number
EZT plus 5000, EZT plus 5002
Digital Technology
One mile range trainer
Beeper/Locator audible from 450 yards away
Lightweight, compact collar and transmitter
16 adjustable intensity levels of Momentary
(‘Nick’) Stimulation, and Constant Stimulation
Gentle Touch System™ Extra Mild Stimulation
MAXX-Range™ Invisible, Embedded Collar
Built in safety shut-off
Three beeper functions - Locate, Run/Point,
Point only
Baritone beeper easier to hear and easier on the
Rechargeable Ni-MH battery system
Completely waterproof collars
Weather resistant transmitter
The EZT plus 5002 comes with two Collar
Receiver units operated from the same
You can change from one collar to the other by
means of a toggle switch on the transmitter
• Before beginning training your dog should be
examined by a veterinarian to assure that your dog
is in good health.
• Never leave your dog unattended with the unit
on. Since no electronic device is perfect, there is a
very slight possibility that your dog may receive an
unintentional electric stimulation.
• Your
EZT plus Super TrainerTM is a very
valuable tool if used correctly. It is extremely
important that you completely understand all the
functions of the collar and how to properly train with
it before placing it on your dog.
• The electrodes on this collar are made with high
grade stainless steel to help prevent any chemical
or allergic reactions with your dog’s skin.
• To prevent neck irritation, the collar should
never be worn for more than 12 hours a day.
Changing the collar location on the dog’s neck
daily will also help prevent irritations. It is
important to keep the collar clean. Clean the
electrodes regularly with a mild anti-bacterial soap.
• If an irritation is found, carefully wash the dog’s neck
with soap and water and then wipe the area with
Hydrogen peroxide. Dry thoroughly and apply an
antibiotic ointment.
Before testing, make sure that both units are fully
charged and the power to the Collar Receiver is “ON”.
To Test the Electronic Stimulation:
A) Place the tester firmly on the
electrodes of the Collar Receiver.
B) Set the intensity (note - an intensity
level setting of 4 or less might not be
enough to light the tester).
C) Push either the ‘NICK’ or ‘STIMU’
D) The tester light will quickly flash for the Nick
function and light steadily when the Constant
Stimulation is pushed (the higher the intensity, the
brighter the test light).
To Test the Beeper:
A) Press the button located on the left side of the
transmitter (Locate button). The collar should
beep any time this button is pressed.
B) Press the button on the right side of the transmitter
(Run/Point button) to activate the Run/Point Mode.
Press the button again to change to Point only
mode. In the Run/Point mode, the collar should
beep every 4-5 seconds while your dog is on the
run, and every 1-2 seconds when your dog is on
point. In the Point only mode, the collar will beep
only when your dog is on point. You can shake
the collar to simulate your dog on the run. Press
the ’Locate’ button to cancel these modes.
Proper collar tightness and position
are very important to insure safety
and correct functioning every time
you use the collar.
• All electronic collars need to be
very snug to work properly.
They must be just tight enough
to allow the “prongs” or
electrodes to make good skin
If your collar is too loose, the stimulation may not
work properly because good skin contact is not
being achieved.
This can directly affect the
stimulation performance and whether or not the dog
will receive the stimulation. Always check for good
“prong” contact if it appears that your dog is not
responding to the stimulation.
A loose collar can promote skin irritation from
moving or rubbing too much on a dog’s neck while
they are running or training. The proper snug fit will
help prevent this from occurring.
Proper fit of the collar is important. It should be tight
enough on the dog’s neck to make good skin
contact and allow the dog to breath normally. The
collar should never be so tight on the dog’s neck
that it restricts the dog’s normal breathing pattern.
For proper positioning of your collar receiver box, it
should be placed on the center of the dog’s neck.
All EZT plus Super TrainerTM collars are equipped
with rechargeable Nickel Metal Hydride (NiMH)
batteries. NiMH batteries are not memory sensitive
and do not require depletion before recharging.
The batteries come partially charged from the factory.
However, it is recommended that you give the battery
a full charge (about 12 hours) before the first use.
Remember - Always keep batteries away from
flammable substances (especially when charging).
When storing the unit for long periods remember to
regularly give the batteries a full charge (12 hours)
once every 4 to 6 weeks.
Battery Charging Procedure
(EZT 5002 shown)
1. Turn the unit off.
2. Plug the charger into a
standard electrical outlet.
3. Charge the batteries for up
to 12 hours. This can be
done either separately or
4. After charging, disconnect the battery charging
cables from the receptacles and securely replace
the rubber battery receptacle covers.
5. Test the system to make sure that everything is
working properly.
Battery Charging Receptacles
The battery charging receptacle is located on the side
of the Transmitter, and on the side of the Collar
Receiver facing the dog’s neck. After charging,
always close the jack with the rubber plug to prevent
foreign particles from getting inside the unit.
Collar Indicator Light
When the Collar Receiver is turned on, the RED light
will flash steadily once every two seconds to indicate
that the unit is active. The RED light changes to a
rapid flash (twice per second) when the battery is low
and in need of charging.
Electrodes should fit snugly on the dog’s neck to
ensure good contact with the skin.
For more
information on the proper fit of the collar, see page 7.
Beeper Horn
The Beeper horn is attached to the collar belt. It will
emit a loud tone audible from up to 450 yards away.
Collar Belt with Embedded Receiver Antenna
The embedded collar antenna is woven into the collar
belt, and runs the along the entire length of the belt.
Collar Receiver
Turning the Unit On:
Press and hold the On/Off button on the Collar Receiver.
The Red LED Indicator will light solidly for two seconds.
Continue holding the Button until the Red light goes off.
The unit is now On. The LED Indicator will now flash
approximately every two seconds. (Note: The
Transmitter is always in a permanent sleep state. It is
only On when a button is being pressed, and does not
need to be turned off by the user).
Turning the Unit Off:
Do not cut the collar belt.
Doing so will damage the antenna and may result in
severely decreased receiver range.
When you are ready to shut the unit off, simply press and
hold the On/Off button for three seconds. The Red LED
indicator will again light solidly for two seconds. Hold the
Button until the light goes off. The Unit is now Off.
Intensity Selection Dial
The intensity selection dial allows
you to choose between sixteen
different levels of stimulation,
allowing for very precise control.
The first and most important step in training your dog
with your EZT Training System is determining the
correct Intensity Level to provide the proper training
stimulation without over-shocking your dog.
To do this place the Collar on the dog’s neck and turn
it on. Place the Intensity Selection dial so that the
System is set on Level One. Press either the ‘NICK’
or the ‘STIMU’ Button. Increase the Intensity Level in
increments of one until the dog is feeling the
stimulation. You should be able to tell when the dog is
feeling the shock by the outward signs of discomfort or
confusion on it’s face. At this point, increase the
Intensity Level by one or two. This should be your
dog’s ideal training level. (Note: Some dog’s may
require more or less stimulation depending upon their
individual nature or size.)
Transmitter Indicator Light
When one of the push button switches on the
transmitter are pushed, the RED light will turn on to
indicate that the transmitter is being operated. When
the battery needs charging the RED light will blink
once every 1/2 second while pushing a button.
Transmitter Antenna
Be very careful when screwing the 4” antenna into the
transmitter. Hand tighten only. Over tightening could
cause damage to the antenna or the antenna mount.
Remote Training Buttons
Pressing the upper button causes the collar to
administer a Momentary Stimulation or ‘Nick’.
Pressing the lower button gives the Continuous
Locate and Run/Point Buttons
Pressing the ‘Locate’ button on the left side of the
Transmitter will make the Collar Receiver beep.
Pressing the ‘Run/Point’ button on the right side of the
Transmitter will activate the Run/Point mode on the
Collar Receiver. Press it again and it will go into the
Point only mode. Press the ‘Locate’ button to cancel
the Run/Point modes.
Two Dog Model Selection Switch
(EZT plus 5002)
Switching between units can be controlled by moving
the toggle selection switch to the desired unit.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF