Daikin | ARX25J3V1B | Service manual | Daikin ARX25J3V1B Service manual

SiBE041010EA
Service
Manual
Inverter Pair
Wall Mounted Type J-Series
[Applied Models]
z Inverter Pair : Heat Pump
SiBE041010EA
Inverter Pair
Wall Mounted Type
J-Series
zHeat Pump
Indoor Unit
FTX20JV1B
FTX25JV1B
FTX35JV1B
ATX20JV1B
ATX25JV1B
ATX35JV1B
FTX20J2V1B
FTX25J2V1B
FTX35J2V1B
ATX20J2V1B
ATX25J2V1B
ATX35J2V1B
Outdoor Unit
RX20JV1B
RX25JV1B
RX35JV1B
ARX20JV1B
ARX25JV1B
ARX35JV1B
RX20J3V1B
RX25J3V1B
RX35J3V1B
ARX20J3V1B
ARX25J3V1B
ARX35J3V1B
The removal procedure for each model is separately bound. Refer to page 103 for the booklet number of
applicable model.
i
Table of Contents
SiBE041010EA
1. Introduction .............................................................................................v
1.1 Safety Cautions ........................................................................................v
1.2 Used Icons ...............................................................................................x
Part 1 List of Functions ................................................................ 1
1. Functions.................................................................................................2
Part 2 Specifications .................................................................... 4
1. Specifications ..........................................................................................5
Part 3 Printed Circuit Board Connector Wiring Diagram ........... 13
1. Indoor Unit.............................................................................................14
2. Outdoor Unit..........................................................................................16
Part 4 Function and Control........................................................ 18
1. Main Functions......................................................................................19
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
1.12
Temperature Control ..............................................................................19
Frequency Principle................................................................................19
Airflow Direction Control.........................................................................21
Fan Speed Control for Indoor Unit .........................................................22
Program Dry Operation ..........................................................................23
Automatic Operation...............................................................................24
Thermostat Control.................................................................................25
NIGHT SET Mode ..................................................................................26
ECONO Operation .................................................................................26
Inverter POWERFUL Operation .............................................................27
Clock Setting ..........................................................................................27
Other Functions......................................................................................28
2. Function of Thermistor ..........................................................................29
3. Control Specification .............................................................................30
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
Mode Hierarchy ......................................................................................30
Frequency Control..................................................................................30
Controls at Mode Changing / Start-up....................................................32
Discharge Pipe Temperature Control.....................................................33
Input Current Control..............................................................................34
Freeze-up Protection Control .................................................................35
Heating Peak-cut Control .......................................................................35
Outdoor Fan Control...............................................................................36
Liquid Compression Protection Function................................................36
Defrost Control .......................................................................................37
Electronic Expansion Valve Control .......................................................38
Malfunctions ...........................................................................................41
Part 5 Remote Controller ............................................................ 42
1. Remote Controller .................................................................................43
Table of Contents
ii
SiBE041010EA
Part 6 Service Diagnosis............................................................. 45
1. Troubleshooting with LED .....................................................................46
1.1 Indoor Unit..............................................................................................46
1.2 Outdoor Unit ...........................................................................................46
2. Problem Symptoms and Measures .......................................................47
3. Service Check Function ........................................................................48
4. Troubleshooting ....................................................................................51
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
4.13
4.14
4.15
4.16
4.17
4.18
4.19
4.20
4.21
4.22
4.23
4.24
Error Codes and Description ..................................................................51
Indoor Unit PCB Abnormality .................................................................52
Freeze-up Protection Control or Heating Peak-cut Control....................53
Fan Motor (DC Motor) or Related Abnormality.......................................54
Thermistor or Related Abnormality (Indoor Unit)....................................56
Refrigerant Shortage ..............................................................................57
Low-voltage Detection or Over-voltage Detection..................................59
Signal Transmission Error (between Indoor Unit and Outdoor Unit) ......61
Unspecified Voltage (between Indoor Unit and Outdoor Unit) ...............63
Outdoor Unit PCB Abnormality...............................................................64
OL Activation (Compressor Overload) ...................................................65
Compressor Lock ...................................................................................67
DC Fan Lock ..........................................................................................68
Input Overcurrent Detection ...................................................................69
Four Way Valve Abnormality..................................................................70
Discharge Pipe Temperature Control.....................................................72
High Pressure Control in Cooling ...........................................................73
Compressor System Sensor Abnormality ..............................................74
Position Sensor Abnormality ..................................................................75
DC Voltage / Current Sensor Abnormality..............................................77
Thermistor or Related Abnormality (Outdoor Unit).................................78
Electrical Box Temperature Rise............................................................80
Radiation Fin Temperature Rise ............................................................81
Output Overcurrent Detection ................................................................83
5. Check ....................................................................................................85
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
5.12
5.13
Thermistor Resistance Check ................................................................85
Fan Motor Connector Output Check ......................................................86
Power Supply Waveforms Check...........................................................87
Electronic Expansion Valve Check.........................................................87
Four Way Valve Performance Check .....................................................88
Inverter Units Refrigerant System Check ...............................................88
Inverter Analyzer Check .........................................................................89
Rotation Pulse Check on the Outdoor Unit PCB ....................................90
Installation Condition Check...................................................................91
Discharge Pressure Check.....................................................................91
Outdoor Fan System Check ...................................................................92
Main Circuit Short Check........................................................................92
Power Module Check .............................................................................93
Part 7 Tips for Servicing ............................................................. 94
1. Tips for Servicing ..................................................................................95
1.1 Pump Down Operation ...........................................................................95
1.2 Forced Cooling Operation ......................................................................95
iii
Table of Contents
SiBE041010EA
2. Trial Operation ......................................................................................96
3. Field Settings ........................................................................................97
3.1 When 2 Units are Installed in 1 Room....................................................97
3.2 Jumper Settings .....................................................................................97
4. Silicon Grease on Power Transistor / Diode Bridge..............................98
Part 8 Appendix........................................................................... 99
1. Piping Diagrams..................................................................................100
1.1 Indoor Unit............................................................................................100
1.2 Outdoor Unit .........................................................................................101
2. Wiring Diagrams..................................................................................102
2.1 Indoor Unit............................................................................................102
2.2 Outdoor Unit .........................................................................................102
3. Removal Procedure (Booklet No.) ......................................................103
Table of Contents
iv
Introduction
SiBE041010EA
1. Introduction
1.1
Safety Cautions
Cautions and
Warnings
„ Be sure to read the following safety cautions before conducting repair work.
„ The caution items are classified into “
Warning” and “
Caution”. The “
Warning”
items are especially important since they can lead to death or serious injury if they are not
followed closely. The “
Caution” items can also lead to serious accidents under some
conditions if they are not followed. Therefore, be sure to observe all the safety caution items
described below.
„ About the pictograms
This symbol indicates the item for which caution must be exercised.
The pictogram shows the item to which attention must be paid.
This symbol indicates the prohibited action.
The prohibited item or action is shown in the illustration or near the symbol.
This symbol indicates the action that must be taken, or the instruction.
The instruction is shown in the illustration or near the symbol.
„ After the repair work is complete, be sure to conduct a test operation to ensure that the
equipment operates normally, and explain the cautions for operating the product to the
customer.
1.1.1 Cautions Regarding Safety of Workers
Warning
Do not store the equipment in a room with successive fire sources (e.g., naked
flame, gas appliance, electric heater).
Be sure to disconnect the power cable plug from the plug socket before
disassembling the equipment for repair.
Working on the equipment that is connected to the power supply may cause an
electrical shock.
If it is necessary to supply power to the equipment to conduct the repair or
inspecting the circuits, do not touch any electrically charged sections of the
equipment.
If the refrigerant gas is discharged during the repair work, do not touch the
discharged refrigerant gas.
The refrigerant gas may cause frostbite.
When disconnecting the suction or discharge pipe of the compressor at the
welded section, evacuate the refrigerant gas completely at a well-ventilated
place first.
If there is gas remaining inside the compressor, the refrigerant gas or
refrigerating machine oil discharges when the pipe is disconnected, and it may
cause injury.
If the refrigerant gas leaks during the repair work, ventilate the area. The
refrigerant gas may generate toxic gases when it contacts flames.
The step-up capacitor supplies high-voltage electricity to the electrical
components of the outdoor unit.
Be sure to discharge the capacitor completely before conducting repair work.
A charged capacitor may cause an electrical shock.
v
SiBE041010EA
Introduction
Warning
Do not start or stop the air conditioner operation by plugging or unplugging the
power cable plug.
Plugging or unplugging the power cable plug to operate the equipment may
cause an electrical shock or fire.
Be sure to wear a safety helmet, gloves, and a safety belt when working at a
high place (more than 2 m). Insufficient safety measures may cause a fall
accident.
In case of R-32 / R-410A refrigerant models, be sure to use pipes, flare nuts
and tools for the exclusive use of the R-32 / R-410A refrigerant.
The use of materials for R-22 refrigerant models may cause a serious accident
such as a damage of refrigerant cycle as well as an equipment failure.
Do not mix air or gas other than the specified refrigerant (R-32 / R-410A / R22) in the refrigerant system.
If air enters the refrigerating system, an excessively high pressure results,
causing equipment damage and injury.
Caution
Do not repair the electrical components with wet hands.
Working on the equipment with wet hands may cause an electrical shock.
Do not clean the air conditioner by splashing water.
Washing the unit with water may cause an electrical shock.
Be sure to provide the grounding when repairing the equipment in a humid or
wet place, to avoid electrical shocks.
Be sure to turn off the power switch and unplug the power cable when cleaning
the equipment.
The internal fan rotates at a high speed, and may cause injury.
Be sure to conduct repair work with appropriate tools.
The use of inappropriate tools may cause injury.
Be sure to check that the refrigerating cycle section has cooled down enough
before conducting repair work.
Working on the unit when the refrigerating cycle section is hot may cause
burns.
vi
Introduction
SiBE041010EA
Caution
Use the welder in a well-ventilated place.
Using the welder in an enclosed room may cause oxygen deficiency.
1.1.2 Cautions Regarding Safety of Users
Warning
Do not store the equipment in a room with successive fire sources (e.g., naked
flame, gas appliance, electric heater).
Be sure to use parts listed in the service parts list of the applicable model and
appropriate tools to conduct repair work. Never attempt to modify the
equipment.
The use of inappropriate parts or tools may cause an electrical shock,
excessive heat generation or fire.
If the power cable and lead wires have scratches or deteriorated, be sure to
replace them.
Damaged cable and wires may cause an electrical shock, excessive heat
generation or fire.
Do not use a joined power cable or extension cable, or share the same power
outlet with other electrical appliances, since it may cause an electrical shock,
excessive heat generation or fire.
Be sure to use an exclusive power circuit for the equipment, and follow the local
technical standards related to the electrical equipment, the internal wiring
regulations, and the instruction manual for installation when conducting
electrical work.
Insufficient power circuit capacity and improper electrical work may cause an
electrical shock or fire.
Be sure to use the specified cable for wiring between the indoor and outdoor
units. Make the connections securely and route the cable properly so that there
is no force pulling the cable at the connection terminals.
Improper connections may cause excessive heat generation or fire.
When wiring between the indoor and outdoor units, make sure that the terminal
cover does not lift off or dismount because of the cable.
If the cover is not mounted properly, the terminal connection section may cause
an electrical shock, excessive heat generation or fire.
Do not damage or modify the power cable.
Damaged or modified power cable may cause an electrical shock or fire.
Placing heavy items on the power cable, and heating or pulling the power cable
may damage the cable.
vii
SiBE041010EA
Introduction
Warning
Do not mix air or gas other than the specified refrigerant (R-32 / R-410A / R22) in the refrigerant system.
If air enters the refrigerating system, an excessively high pressure results,
causing equipment damage and injury.
If the refrigerant gas leaks, be sure to locate the leaking point and repair it
before charging the refrigerant. After charging refrigerant, make sure that there
is no refrigerant leak.
If the leaking point cannot be located and the repair work must be stopped, be
sure to perform pump-down and close the service valve, to prevent the
refrigerant gas from leaking into the room. The refrigerant gas itself is
harmless, but it may generate toxic gases when it contacts flames, such as fan
and other heaters, stoves and ranges.
When relocating the equipment, make sure that the new installation site has
sufficient strength to withstand the weight of the equipment.
If the installation site does not have sufficient strength and if the installation
work is not conducted securely, the equipment may fall and cause injury.
Check to make sure that the power cable plug is not dirty or loose, then insert
the plug into a power outlet securely.
If the plug has dust or loose connection, it may cause an electrical shock or fire.
Be sure to install the product correctly by using the provided standard
For unitary type
installation frame.
only
Incorrect use of the installation frame and improper installation may cause the
equipment to fall, resulting in injury.
Be sure to install the product securely in the installation frame mounted on the For unitary type
window frame.
only
If the unit is not securely mounted, it may fall and cause injury.
When replacing the coin battery in the remote controller, be sure to dispose of
the old battery to prevent children from swallowing it.
If a child swallows the coin battery, see a doctor immediately.
Caution
Installation of a leakage breaker is necessary in some cases depending on the
conditions of the installation site, to prevent electrical shocks.
Do not install the equipment in a place where there is a possibility of
combustible gas leaks.
If the combustible gas leaks and remains around the unit, it may cause a fire.
viii
Introduction
SiBE041010EA
Caution
Check to see if the parts and wires are mounted and connected properly, and
if the connections at the soldered or crimped terminals are secure.
Improper installation and connections may cause excessive heat generation,
fire or an electrical shock.
If the installation platform or frame has corroded, replace it.
Corroded installation platform or frame may cause the unit to fall, resulting in
injury.
Check the grounding, and repair it if the equipment is not properly grounded.
Improper grounding may cause an electrical shock.
Be sure to measure the insulation resistance after the repair, and make sure
that the resistance is 1 MΩ or higher.
Faulty insulation may cause an electrical shock.
Be sure to check the drainage of the indoor unit after the repair.
Faulty drainage may cause the water to enter the room and wet the furniture
and floor.
Do not tilt the unit when removing it.
The water inside the unit may spill and wet the furniture and floor.
Be sure to install the packing and seal on the installation frame properly.
For unitary type
If the packing and seal are not installed properly, water may enter the room and only
wet the furniture and floor.
ix
SiBE041010EA
1.2
Introduction
Used Icons
Icons are used to attract the attention of the reader to specific information. The meaning of each
icon is described in the table below:
Icon
Type of
Information
Note
Description
Caution
A “caution” is used when there is danger that the reader, through
incorrect manipulation, may damage equipment, loose data, get
an unexpected result or has to restart (part of) a procedure.
Warning
A “warning” is used when there is danger of personal injury.
Reference
A “reference” guides the reader to other places in this binder or
in this manual, where he/she will find additional information on a
specific topic.
A “note” provides information that is not indispensable, but may
nevertheless be valuable to the reader, such as tips and tricks.
Note:
Caution
Warning
x
SiBE041010EA
Part 1
List of Functions
1. Functions.................................................................................................2
1
List of Functions
SiBE041010EA
Functions
FTX20/25/35J2V1B
RX20/25/35J3V1B
FTX20/25/35J2V1B
RX20/25/35J3V1B
FTX20/25/35JV1B
RX20/25/35JV1B
FTX20/25/35JV1B
RX20/25/35JV1B
1. Functions
z
z
Air-purifying filter
—
—
Operation limit for cooling (°CDB)
10
~46
10
~46
Photocatalytic deodorizing filter
—
—
Operation limit for heating (°CWB)
–15
~18
–15
~18
Air-purifying filter with photocatalytic
deodorizing function
—
—
PAM control
z
z
Standby electricity saving
z
z
Titanium apatite photocatalytic
air-purifying filter
z
z
Oval scroll compressor
—
—
Air filter (prefilter)
z
z
Swing compressor
z
z
Wipe-clean flat panel
z
z
Rotary compressor
—
—
Washable grille
—
—
Reluctance DC motor
z
z
MOLD PROOF operation
—
—
Power-airflow flap
z
z
Heating dry operation
—
—
Power-airflow dual flaps
—
—
Good-sleep cooling operation
—
—
Power-airflow diffuser
—
—
Category
Basic
Function
Compressor
Comfortable
Airflow
Comfort
Control
Operation
Lifestyle
Convenience
Functions
Inverter
(with inverter power control)
Category
Health &
Clean
Timer
Functions
WEEKLY TIMER operation
—
—
24-hour ON/OFF TIMER
z
z
NIGHT SET mode
z
z
Auto-restart (after power failure)
z
z
Self-diagnosis (digital, LED) display
z
z
Wide-angle louvers
z
z
Vertical auto-swing (up and down)
z
z
Horizontal auto-swing (right and left)
—
—
3-D airflow
—
—
COMFORT AIRFLOW operation
z
z
Wiring error check function
—
—
Auto fan speed
z
z
Anti-corrosion treatment of outdoor heat
exchanger
z
z
Indoor unit quiet operation
z
z
Multi-split / split type compatible indoor
unit
z
z
NIGHT QUIET mode (automatic)
—
—
Flexible power supply correspondence
—
—
OUTDOOR UNIT QUIET operation
(manual)
—
—
High ceiling application
—
—
INTELLIGENT EYE operation
—
—
Chargeless
Quick warming function
(preheating operation)
z
z
Either side drain (right or left)
z
z
Hot-start function
z
z
Power selection
—
—
Automatic defrosting
z
z
Automatic operation
z
z
5-room centralized controller (option)
—
—
Program dry operation
z
z
Fan only
z
z
Remote control adaptor
(normal open pulse contact) (option)
—
—
New POWERFUL operation
(non-inverter)
—
—
Remote control adaptor
(normal open contact) (option)
—
—
Worry Free
“Reliability &
Durability”
Flexibility
Remote
Control
10 m 10 m
Inverter POWERFUL operation
z
z
DIII-NET compatible (adaptor) (option)
—
—
Priority-room setting
—
—
Wireless
z
z
COOL / HEAT mode lock
—
—
Wired (option)
z
z
HOME LEAVE operation
—
—
ECONO operation
z
z
Indoor unit [ON/OFF] button
z
z
Signal receiving sign
z
z
R/C with back light
—
—
Temperature display
—
—
Remote
Controller
Note: z : Available
— : Not available
List of Functions
2
ATX20/25/35JV1B
ARX20/25/35JV1B
ATX20/25/35J2V1B
ARX20/25/35J3V1B
ATX20/25/35J2V1B
ARX20/25/35J3V1B
SiBE041010EA
ATX20/25/35JV1B
ARX20/25/35JV1B
Functions
z
z
Air-purifying filter
—
—
Operation limit for cooling (°CDB)
10
~46
10
~46
Photocatalytic deodorizing filter
—
—
Operation limit for heating (°CWB)
–15
~18
–15
~18
Air-purifying filter with photocatalytic
deodorizing function
—
—
PAM control
z
z
Standby electricity saving
z
z
Titanium apatite photocatalytic
air-purifying filter
z
z
Oval scroll compressor
—
—
Air filter (prefilter)
z
z
Swing compressor
z
z
Wipe-clean flat panel
z
z
Rotary compressor
—
—
Washable grille
—
—
Reluctance DC motor
z
z
MOLD PROOF operation
—
—
Category
Basic
Function
Compressor
Comfortable
Airflow
Comfort
Control
Operation
Lifestyle
Convenience
Functions
Inverter
(with inverter power control)
Category
Health &
Clean
Functions
Power-airflow flap
z
z
Heating dry operation
—
—
Power-airflow dual flaps
—
—
Good-sleep cooling operation
—
—
Power-airflow diffuser
—
—
Timer
WEEKLY TIMER operation
—
—
24-hour ON/OFF TIMER
z
z
NIGHT SET mode
z
z
Auto-restart (after power failure)
z
z
Self-diagnosis (digital, LED) display
z
z
Wide-angle louvers
z
z
Vertical auto-swing (up and down)
z
z
Horizontal auto-swing (right and left)
—
—
3-D airflow
—
—
COMFORT AIRFLOW operation
z
z
Wiring error check function
—
—
Anti-corrosion treatment of outdoor heat
exchanger
z
z
Multi-split / split type compatible indoor
unit
z
z
Worry Free
“Reliability &
Durability”
Auto fan speed
z
z
Indoor unit quiet operation
z
z
NIGHT QUIET mode (automatic)
—
—
Flexible power supply correspondence
—
—
OUTDOOR UNIT QUIET operation
(manual)
—
—
High ceiling application
—
—
INTELLIGENT EYE operation
—
—
Chargeless
Quick warming function
(preheating operation)
z
z
Either side drain (right or left)
z
z
Hot-start function
z
z
Power selection
—
—
Automatic defrosting
z
z
Automatic operation
z
z
5-room centralized controller (option)
—
—
Program dry operation
z
z
Fan only
z
z
Remote control adaptor
(normal open pulse contact) (option)
—
—
New POWERFUL operation
(non-inverter)
—
—
Remote control adaptor
(normal open contact) (option)
—
—
Flexibility
Remote
Control
10 m 10 m
Inverter POWERFUL operation
z
z
DIII-NET compatible (adaptor) (option)
—
—
Priority-room setting
—
—
Wireless
z
z
COOL / HEAT mode lock
—
—
Wired (option)
z
z
HOME LEAVE operation
—
—
ECONO operation
z
z
Indoor unit [ON/OFF] button
z
z
Signal receiving sign
z
z
R/C with back light
—
—
Temperature display
—
—
Remote
Controller
Note: z : Available
— : Not available
3
List of Functions
SiBE041010EA
Part 2
Specifications
1. Specifications ..........................................................................................5
Specifications
4
Specifications
SiBE041010EA
1. Specifications
50 Hz, 230 V
Indoor Unit
Model
FTX20JV1B
RX20JV1B
Outdoor Unit
Capacity
Rated (Min. ~ Max.)
Running Current (Rated)
Power Consumption
Rated (Min. ~ Max.)
Power Factor (Rated)
COP Rated (Min. ~ Max.)
Liquid
Piping
Connections Gas
Drain
Heat Insulation
Max. Interunit Piping Length
Max. Interunit Height Difference
Chargeless
Amount of Additional Charge
of Refrigerant
Indoor Unit
Front Panel Color
H
Airflow Rate
Heating
2.5 (1.3 ~ 3.5)
8,500 (4,400 ~ 11,600)
2,150 (1,120 ~ 3,010)
3.0
Cooling
2.5 (1.3 ~ 3.0)
8,500 (4,400 ~ 10,200)
2,150 (1,120 ~ 2,580)
3.7
Heating
2.8 (1.3 ~ 4.0)
9,600 (4,400 ~ 13,600)
2,410 (1,120 ~ 3,440)
3.2
W
550 (310 ~ 720)
590 (250 ~ 950)
730 (310 ~ 1,050)
690 (250 ~ 1,110)
%
W/W
mm
mm
mm
88.6
3.64 (4.19 ~ 3.61)
91.6
4.24 (5.20 ~ 3.68)
85.8
3.42 (4.19 ~ 2.86)
93.8
4.06 (5.20 ~ 3.60)
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H × W × D)
Packaged Dimensions (H × W × D)
Weight (Mass)
Gross Weight (Gross Mass)
Sound
Pressure
H / M / L / SL
Level
Sound Power Level
Outdoor Unit
Casing Color
Type
Compressor Model
Motor Output
Type
Refrigerant
Oil
Charge
Type
Refrigerant
Charge
H
Type
Fan
Motor Output
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Starting Current
Dimensions (H × W × D)
Packaged Dimensions (H × W × D)
Weight (Mass)
Gross Weight (Gross Mass)
Sound Pressure Level (H)
Sound Power Level (H)
Drawing No.
Note:
5
Cooling
2.0 (1.3 ~ 2.6)
6,800 (4,400 ~ 8,900)
1,720 (1,120 ~ 2,240)
2.7
φ 6.4
φ 9.5
φ 18.0
Both Liquid and Gas Pipes
15
12
10
g/m
Fan
Airflow Rate
kW
Btu/h
kcal/h
A
m
m
m
M
L
SL
FTX25JV1B
RX25JV1B
W
Steps
A
W
%
mm
mm
kg
kg
20
FTX25JV1B
White
9.4 (331)
7.8 (276)
6.3 (222)
5.5 (194)
9.2 (325)
7.6 (268)
6.0 (212)
4.8 (169)
Cross Flow Fan
16
5 Steps, Quiet, Auto
Right, Left, Horizontal, Downward
Removable / Washable / Mildew Proof
0.18
0.18
40
40
96.6
96.6
Microcomputer Control
283 × 770 × 198
263 × 840 × 344
7
11
39 / 33 / 25 / 22
dB
55
L
39 / 34 / 28 / 25
29.2 (1,030)
40 / 33 / 26 / 22
40 / 34 / 28 / 25
56
56
RX25JV1B
Ivory White
Hermetically Sealed Swing Type
1YC23AEXD
750
FVC50K
0.375
R-410A
0.74
26.2 (927)
29.2 (1,030)
Propeller
33
2.52
510
88.0
9.7 (342)
8.0 (283)
6.3 (222)
5.5 (194)
Cross Flow Fan
16
5 Steps, Quiet, Auto
Right, Left, Horizontal, Downward
Removable / Washable / Mildew Proof
0.18
0.18
40
40
96.6
96.6
Microcomputer Control
283 × 770 × 198
263 × 840 × 344
7
11
55
RX20JV1B
Ivory White
Hermetically Sealed Swing Type
1YC23AEXD
750
FVC50K
0.375
R-410A
0.74
W
W
A
W
%
A
mm
mm
kg
kg
dB(A)
dB
20
FTX20JV1B
White
9.1 (321)
7.4 (261)
5.9 (208)
4.7 (166)
dB(A)
kg
m³/min
(cfm)
φ 6.4
φ 9.5
φ 18.0
Both Liquid and Gas Pipes
15
12
10
26.2 (927)
Propeller
33
2.62
550
91.3
3.52
690
85.2
2.7
550 × 658 × 275
616 × 788 × 359
28
31
46
60
3.02
650
93.6
3.7
550 × 658 × 275
616 × 788 × 359
28
31
47
61
46
60
3D065930
47
61
3D065931
„ The data are based on the conditions shown in the table below.
Cooling
Heating
Piping Length
Indoor ; 27°CDB / 19°CWB
Outdoor ; 35°CDB / 24°CWB
Indoor ; 20°CDB
Outdoor ; 7°CDB / 6°CWB
5m
Conversion Formulae
kcal/h = kW × 860
Btu/h = kW × 3412
cfm = m³/min × 35.3
Specifications
SiBE041010EA
Specifications
50 Hz, 230 V
Indoor Unit
Model
FTX35JV1B
RX35JV1B
Outdoor Unit
Capacity
Rated (Min. ~ Max.)
Running Current (Rated)
Power Consumption
Rated (Min. ~ Max.)
Power Factor
COP Rated (Min. ~ Max.)
Liquid
Piping
Connections Gas
Drain
Heat Insulation
Max. Interunit Piping Length
Max. Interunit Height Difference
Chargeless
Amount of Additional Charge
of Refrigerant
Indoor Unit
Front Panel Color
H
Airflow Rate
Heating
3.5 (1.3 ~ 4.8)
11,900 (4,400 ~ 16,400)
3,010 (1,120 ~ 4,130)
4.7
W
980 (290 ~ 1,300)
930 (290 ~ 1,290)
%
W/W
mm
mm
mm
81.9
3.37 (4.48 ~ 2.92)
86.0
3.76 (4.48 ~ 3.72)
20
FTX35JV1B
White
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H × W × D)
Packaged Dimensions (H × W × D)
Weight (Mass)
Gross Weight (Gross Mass)
Sound
Pressure
H / M / L / SL
Level
Sound Power Level
Outdoor Unit
Casing Color
Type
Compressor Model
Motor Output
Type
Refrigerant
Oil
Charge
Type
Refrigerant
Charge
H
Type
Fan
Motor Output
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Starting Current
Dimensions (H × W × D)
Packaged Dimensions (H × W × D)
Weight (Mass)
Gross Weight (Gross Mass)
Sound Pressure Level (H)
Sound Power Level (H)
Drawing No.
Note:
φ 6.4
φ 9.5
φ 18.0
Both Liquid and Gas Pipes
15
12
10
g/m
M
L
SL
Specifications
Cooling
3.3 (1.3 ~ 3.8)
11,300 (4,400 ~ 13,000)
2,840 (1,120 ~ 3,270)
5.2
m
m
m
Fan
Airflow Rate
kW
Btu/h
kcal/h
A
9.3 (328)
7.7 (272)
6.1 (215)
4.9 (173)
Cross Flow Fan
16
5 Steps, Quiet, Auto
Right, Left, Horizontal, Downward
Removable / Washable / Mildew Proof
W
Steps
A
W
%
10.1 (356)
8.4 (295)
6.7 (235)
5.7 (201)
0.18
40
96.6
0.18
40
96.6
Microcomputer Control
283 × 770 × 198
263 × 840 × 344
7
11
mm
mm
kg
kg
dB(A)
41 / 34 / 27 / 23
dB
57
L
W
A
W
%
A
mm
mm
kg
kg
dB(A)
dB
57
RX35JV1B
Ivory White
Hermetically Sealed Swing Type
1YC23AEXD
750
FVC50K
0.375
R-410A
1.0
W
kg
m³/min
(cfm)
41 / 35 / 29 / 26
27.6 (975)
24.5 (865)
Propeller
33
5.02
940
86.0
4.52
890
85.6
5.0
550 × 658 × 275
616 × 788 × 359
30
34
48
62
48
62
3D065932
„ The data are based on the conditions shown in the table below.
Cooling
Heating
Piping Length
Indoor ; 27°CDB / 19°CWB
Outdoor ; 35°CDB / 24°CWB
Indoor ; 20°CDB
Outdoor ; 7°CDB / 6°CWB
5m
Conversion Formulae
kcal/h = kW × 860
Btu/h = kW × 3412
cfm = m³/min × 35.3
6
Specifications
SiBE041010EA
50 Hz, 230 V
Indoor Unit
Model
FTX20J2V1B
RX20J3V1B
Outdoor Unit
Capacity
Rated (Min. ~ Max.)
Running Current (Rated)
Power Consumption
Rated (Min. ~ Max.)
Power Factor (Rated)
COP Rated (Min. ~ Max.)
Liquid
Piping
Connections Gas
Drain
Heat Insulation
Max. Interunit Piping Length
Max. Interunit Height Difference
Chargeless
Amount of Additional Charge
of Refrigerant
Indoor Unit
Front Panel Color
H
Airflow Rate
Heating
2.5 (1.3 ~ 3.5)
8,500 (4,400 ~ 11,900)
2,150 (1,120 ~ 3,010)
3.0
Cooling
2.5 (1.3 ~ 3.0)
8,500 (4,400 ~ 10,200)
2,150 (1,120 ~ 2,580)
3.7
Heating
2.8 (1.3 ~ 4.0)
9,600 (4,400 ~ 13,600)
2,410 (1,120 ~ 3,440)
3.2
W
550 (310 ~ 720)
590 (250 ~ 950)
730 (310 ~ 1,050)
690 (250 ~ 1,110)
%
W/W
mm
mm
mm
88.6
3.64 (4.19 ~ 3.61)
85.5
4.24 (5.20 ~ 3.68)
85.8
3.42 (4.19 ~ 2.86)
93.8
4.06 (5.20 ~ 3.60)
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H × W × D)
Packaged Dimensions (H × W × D)
Weight (Mass)
Gross Weight (Gross Mass)
Sound
Pressure
H / M / L / SL
Level
Sound Power Level
Outdoor Unit
Casing Color
Type
Compressor Model
Motor Output
Type
Refrigerant
Oil
Charge
Type
Refrigerant
Charge
H
Type
Fan
Motor Output
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Starting Current
Dimensions (H × W × D)
Packaged Dimensions (H × W × D)
Weight (Mass)
Gross Weight (Gross Mass)
Sound Pressure Level (H)
Sound Power Level (H)
Drawing No.
Note:
7
Cooling
2.0 (1.3 ~ 2.6)
6,800 (4,400 ~ 8,900)
1,720 (1,120 ~ 2,240)
2.7
φ 6.4
φ 9.5
φ 18.0
Both Liquid and Gas Pipes
15
12
10
g/m
Fan
Airflow Rate
kW
Btu/h
kcal/h
A
m
m
m
M
L
SL
FTX25J2V1B
RX25J3V1B
W
Steps
A
W
%
mm
mm
kg
kg
20
FTX25J2V1B
White
9.4 (331)
7.8 (276)
6.3 (222)
5.5 (194)
9.2 (325)
7.6 (268)
6.0 (212)
4.8 (169)
Cross Flow Fan
16
5 Steps, Quiet, Auto
Right, Left, Horizontal, Downward
Removable / Washable / Mildew Proof
0.18
0.18
40
40
96.6
96.6
Microcomputer Control
283 × 770 × 198
266 × 846 × 345
7
11
39 / 33 / 25 / 22
dB
55
L
39 / 34 / 28 / 25
29.2 (1,030)
40 / 33 / 26 / 22
40 / 34 / 28 / 25
55
55
RX25J3V1B
Ivory White
Hermetically Sealed Swing Type
1YC23AEXD
750
FVC50K
0.375
R-410A
0.74
26.2 (927)
29.2 (1,030)
Propeller
33
2.52
510
88.0
9.7 (342)
8.0 (283)
6.3 (222)
5.5 (194)
Cross Flow Fan
16
5 Steps, Quiet, Auto
Right, Left, Horizontal, Downward
Removable / Washable / Mildew Proof
0.18
0.18
40
40
96.6
96.6
Microcomputer Control
283 × 770 × 198
266 × 846 × 345
7
11
55
RX20J3V1B
Ivory White
Hermetically Sealed Swing Type
1YC23AEXD
750
FVC50K
0.375
R-410A
0.74
W
W
A
W
%
A
mm
mm
kg
kg
dB(A)
dB
20
FTX20J2V1B
White
9.1 (321)
7.4 (261)
5.9 (208)
4.7 (166)
dB(A)
kg
m³/min
(cfm)
φ 6.4
φ 9.5
φ 18.0
Both Liquid and Gas Pipes
15
12
10
26.2 (927)
Propeller
33
2.82
550
84.8
3.52
690
85.2
3.0
550 × 658 × 275
612 × 769 × 350
28
31
46
60
3.02
650
93.6
3.7
550 × 658 × 275
612 × 769 × 350
28
31
47
61
46
60
C: 3D080673
47
61
C: 3D080674
„ The data are based on the conditions shown in the table below.
Cooling
Heating
Piping Length
Indoor ; 27°CDB / 19°CWB
Outdoor ; 35°CDB / 24°CWB
Indoor ; 20°CDB
Outdoor ; 7°CDB / 6°CWB
5m
Conversion Formulae
kcal/h = kW × 860
Btu/h = kW × 3412
cfm = m³/min × 35.3
Specifications
SiBE041010EA
Specifications
50 Hz, 230 V
Indoor Unit
Model
FTX35J2V1B
RX35J3V1B
Outdoor Unit
Capacity
Rated (Min. ~ Max.)
Running Current (Rated)
Power Consumption
Rated (Min. ~ Max.)
Power Factor
COP Rated (Min. ~ Max.)
Liquid
Piping
Connections Gas
Drain
Heat Insulation
Max. Interunit Piping Length
Max. Interunit Height Difference
Chargeless
Amount of Additional Charge
of Refrigerant
Indoor Unit
Front Panel Color
H
Airflow Rate
Heating
3.5 (1.3 ~ 4.8)
11,900 (4,400 ~ 16,400)
3,010 (1,120 ~ 4,130)
4.7
W
980 (290 ~ 1,300)
930 (290 ~ 1,290)
%
W/W
mm
mm
mm
81.9
3.37 (4.48 ~ 2.92)
86.0
3.76 (4.48 ~ 3.72)
20
FTX35J2V1B
White
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H × W × D)
Packaged Dimensions (H × W × D)
Weight (Mass)
Gross Weight (Gross Mass)
Sound
Pressure
H / M / L / SL
Level
Sound Power Level
Outdoor Unit
Casing Color
Type
Compressor Model
Motor Output
Type
Refrigerant
Oil
Charge
Type
Refrigerant
Charge
H
Type
Fan
Motor Output
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Starting Current
Dimensions (H × W × D)
Packaged Dimensions (H × W × D)
Weight (Mass)
Gross Weight (Gross Mass)
Sound Pressure Level (H)
Sound Power Level (H)
Drawing No.
Note:
φ 6.4
φ 9.5
φ 18.0
Both Liquid and Gas Pipes
15
12
10
g/m
M
L
SL
Specifications
Cooling
3.3 (1.3 ~ 3.8)
11,300 (4,400 ~ 13,000)
2,840 (1,120 ~ 3,270)
5.2
m
m
m
Fan
Airflow Rate
kW
Btu/h
kcal/h
A
9.3 (328)
7.7 (272)
6.1 (215)
4.9 (173)
Cross Flow Fan
16
5 Steps, Quiet, Auto
Right, Left, Horizontal, Downward
Removable / Washable / Mildew Proof
W
Steps
A
W
%
10.1 (356)
8.4 (295)
6.7 (235)
5.7 (201)
0.18
40
96.6
0.18
40
96.6
Microcomputer Control
283 × 770 × 198
266 × 846 × 345
7
11
mm
mm
kg
kg
dB(A)
41 / 34 / 27 / 23
dB
58
L
W
A
W
%
A
mm
mm
kg
kg
dB(A)
dB
58
RX35J3V1B
Ivory White
Hermetically Sealed Swing Type
1YC23AEXD
750
FVC50K
0.375
R-410A
1.0
W
kg
m³/min
(cfm)
41 / 35 / 29 / 26
27.6 (975)
24.5 (865)
Propeller
33
5.02
940
81.4
4.52
890
85.6
5.2
550 × 658 × 275
612 × 769 × 350
30
34
48
62
48
62
C: 3D080675
„ The data are based on the conditions shown in the table below.
Cooling
Heating
Piping Length
Indoor ; 27°CDB / 19°CWB
Outdoor ; 35°CDB / 24°CWB
Indoor ; 20°CDB
Outdoor ; 7°CDB / 6°CWB
5m
Conversion Formulae
kcal/h = kW × 860
Btu/h = kW × 3412
cfm = m³/min × 35.3
8
Specifications
SiBE041010EA
50 Hz, 230 V
Indoor Unit
Model
ATX20JV1B
ARX20JV1B
Outdoor Unit
Capacity
Rated (Min. ~ Max.)
Running Current (Rated)
Power Consumption
Rated (Min. ~ Max.)
Power Factor (Rated)
COP Rated (Min. ~ Max.)
Liquid
Piping
Connections Gas
Drain
Heat Insulation
Max. Interunit Piping Length
Max. Interunit Height Difference
Chargeless
Amount of Additional Charge
of Refrigerant
Indoor Unit
Front Panel Color
H
Airflow Rate
Heating
2.5 (1.3 ~ 3.5)
8,500 (4,400 ~ 11,600)
2,150 (1,120 ~ 3,010)
3.0
Cooling
2.5 (1.3 ~ 3.0)
8,500 (4,400 ~ 10,200)
2,150 (1,120 ~ 2,580)
3.7
Heating
2.8 (1.3 ~ 4.0)
9,600 (4,400 ~ 13,600)
2,410 (1,120 ~ 3,440)
3.2
W
550 (310 ~ 720)
590 (250 ~ 950)
730 (310 ~ 1,050)
690 (250 ~ 1,110)
%
W/W
mm
mm
mm
88.6
3.64 (4.19 ~ 3.61)
91.6
4.24 (5.20 ~ 3.68)
85.8
3.42 (4.19 ~ 2.86)
93.8
4.06 (5.20 ~ 3.60)
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H × W × D)
Packaged Dimensions (H × W × D)
Weight (Mass)
Gross Weight (Gross Mass)
Sound
Pressure
H / M / L / SL
Level
Sound Power Level
Outdoor Unit
Casing Color
Type
Compressor Model
Motor Output
Type
Refrigerant
Oil
Charge
Type
Refrigerant
Charge
H
Type
Fan
Motor Output
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Starting Current
Dimensions (H × W × D)
Packaged Dimensions (H × W × D)
Weight (Mass)
Gross Weight (Gross Mass)
Sound Pressure Level (H)
Sound Power Level (H)
Drawing No.
Note:
9
Cooling
2.0 (1.3 ~ 2.6)
6,800 (4,400 ~ 8,900)
1,720 (1,120 ~ 2,240)
2.7
φ 6.4
φ 9.5
φ 18.0
Both Liquid and Gas Pipes
15
12
10
g/m
Fan
Airflow Rate
kW
Btu/h
kcal/h
A
m
m
m
M
L
SL
ATX25JV1B
ARX25JV1B
W
Steps
A
W
%
mm
mm
kg
kg
20
ATX25JV1B
White
9.4 (331)
7.8 (276)
6.3 (222)
5.5 (194)
9.2 (325)
7.6 (268)
6.0 (212)
4.8 (169)
Cross Flow Fan
16
5 Steps, Quiet, Auto
Right, Left, Horizontal, Downward
Removable / Washable / Mildew Proof
0.18
0.18
40
40
96.6
96.6
Microcomputer Control
283 × 770 × 198
263 × 840 × 344
7
11
39 / 33 / 25 / 22
dB
55
L
39 / 34 / 28 / 25
29.2 (1,030)
40 / 33 / 26 / 22
40 / 34 / 28 / 25
56
56
ARX25JV1B
Ivory White
Hermetically Sealed Swing Type
1YC23AEXD
750
FVC50K
0.375
R-410A
0.74
26.2 (927)
29.2 (1,030)
Propeller
33
2.52
510
88.0
9.7 (342)
8.0 (283)
6.3 (222)
5.5 (194)
Cross Flow Fan
16
5 Steps, Quiet, Auto
Right, Left, Horizontal, Downward
Removable / Washable / Mildew Proof
0.18
0.18
40
40
96.6
96.6
Microcomputer Control
283 × 770 × 198
263 × 840 × 344
7
11
55
ARX20JV1B
Ivory White
Hermetically Sealed Swing Type
1YC23AEXD
750
FVC50K
0.375
R-410A
0.74
W
W
A
W
%
A
mm
mm
kg
kg
dB(A)
dB
20
ATX20JV1B
White
9.1 (321)
7.4 (261)
5.9 (208)
4.7 (166)
dB(A)
kg
m³/min
(cfm)
φ 6.4
φ 9.5
φ 18.0
Both Liquid and Gas Pipes
15
12
10
26.2 (927)
Propeller
33
2.62
550
91.3
3.52
690
85.2
2.7
550 × 658 × 275
616 × 788 × 359
28
31
46
60
3.02
650
93.6
3.7
550 × 658 × 275
616 × 788 × 359
28
31
47
61
46
60
3D065933
47
61
3D065934
„ The data are based on the conditions shown in the table below.
Cooling
Heating
Piping Length
Indoor ; 27°CDB / 19°CWB
Outdoor ; 35°CDB / 24°CWB
Indoor ; 20°CDB
Outdoor ; 7°CDB / 6°CWB
5m
Conversion Formulae
kcal/h = kW × 860
Btu/h = kW × 3412
cfm = m³/min × 35.3
Specifications
SiBE041010EA
Specifications
50 Hz, 230 V
Indoor Unit
Model
ATX35JV1B
ARX35JV1B
Outdoor Unit
Capacity
Rated (Min. ~ Max.)
Running Current (Rated)
Power Consumption
Rated (Min. ~ Max.)
Power Factor
COP Rated (Min. ~ Max.)
Liquid
Piping
Connections Gas
Drain
Heat Insulation
Max. Interunit Piping Length
Max. Interunit Height Difference
Chargeless
Amount of Additional Charge
of Refrigerant
Indoor Unit
Front Panel Color
H
Airflow Rate
Heating
3.5 (1.3 ~ 4.8)
11,900 (4,400 ~ 16,400)
3,010 (1,120 ~ 4,130)
4.7
W
980 (290 ~ 1,300)
930 (290 ~ 1,290)
%
W/W
mm
mm
mm
81.9
3.37 (4.48 ~ 2.92)
86.0
3.76 (4.48 ~ 3.72)
20
ATX35JV1B
White
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H × W × D)
Packaged Dimensions (H × W × D)
Weight (Mass)
Gross Weight (Gross Mass)
Sound
Pressure
H / M / L / SL
Level
Sound Power Level
Outdoor Unit
Casing Color
Type
Compressor Model
Motor Output
Type
Refrigerant
Oil
Charge
Type
Refrigerant
Charge
H
Type
Fan
Motor Output
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Starting Current
Dimensions (H × W × D)
Packaged Dimensions (H × W × D)
Weight (Mass)
Gross Weight (Gross Mass)
Sound Pressure Level (H)
Sound Power Level (H)
Drawing No.
Note:
φ 6.4
φ 9.5
φ 18.0
Both Liquid and Gas Pipes
15
12
10
g/m
M
L
SL
Specifications
Cooling
3.3 (1.3 ~ 3.8)
11,300 (4,400 ~ 13,000)
2,840 (1,120 ~ 3,270)
5.2
m
m
m
Fan
Airflow Rate
kW
Btu/h
kcal/h
A
9.3 (328)
7.7 (272)
6.1 (215)
4.9 (173)
Cross Flow Fan
16
5 Steps, Quiet, Auto
Right, Left, Horizontal, Downward
Removable / Washable / Mildew Proof
W
Steps
A
W
%
10.1 (356)
8.4 (295)
6.7 (235)
5.7 (201)
0.18
40
96.6
0.18
40
96.6
Microcomputer Control
283 × 770 × 198
263 × 840 × 344
7
11
mm
mm
kg
kg
dB(A)
41 / 34 / 27 / 23
dB
57
L
W
A
W
%
A
mm
mm
kg
kg
dB(A)
dB
57
ARX35JV1B
Ivory White
Hermetically Sealed Swing Type
1YC23AEXD
750
FVC50K
0.375
R-410A
1.0
W
kg
m³/min
(cfm)
41 / 35 / 29 / 26
27.6 (975)
24.5 (865)
Propeller
33
5.02
940
86.0
4.52
890
85.6
5.0
550 × 658 × 275
616 × 788 × 359
30
34
48
62
48
62
3D065935
„ The data are based on the conditions shown in the table below.
Cooling
Heating
Piping Length
Indoor ; 27°CDB / 19°CWB
Outdoor ; 35°CDB / 24°CWB
Indoor ; 20°CDB
Outdoor ; 7°CDB / 6°CWB
5m
Conversion Formulae
kcal/h = kW × 860
Btu/h = kW × 3412
cfm = m³/min × 35.3
10
Specifications
SiBE041010EA
50 Hz, 230 V
Indoor Unit
Model
ATX20J2V1B
ARX20J3V1B
Outdoor Unit
Capacity
Rated (Min. ~ Max.)
Running Current (Rated)
Power Consumption
Rated (Min. ~ Max.)
Power Factor (Rated)
COP Rated (Min. ~ Max.)
Liquid
Piping
Connections Gas
Drain
Heat Insulation
Max. Interunit Piping Length
Max. Interunit Height Difference
Chargeless
Amount of Additional Charge
of Refrigerant
Indoor Unit
Front Panel Color
H
Airflow Rate
Heating
2.5 (1.3 ~ 3.5)
8,500 (4,400 ~ 11,900)
2,150 (1,120 ~ 3,010)
3.0
Cooling
2.5 (1.3 ~ 3.0)
8,500 (4,400 ~ 10,200)
2,150 (1,120 ~ 2,580)
3.7
Heating
2.8 (1.3 ~ 4.0)
9,600 (4,400 ~ 13,600)
2,410 (1,120 ~ 3,440)
3.2
W
550 (310 ~ 720)
590 (250 ~ 950)
730 (310 ~ 1,050)
690 (250 ~ 1,110)
%
W/W
mm
mm
mm
88.6
3.64 (4.19 ~ 3.61)
85.5
4.24 (5.20 ~ 3.68)
85.8
3.42 (4.19 ~ 2.86)
93.8
4.06 (5.20 ~ 3.60)
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H × W × D)
Packaged Dimensions (H × W × D)
Weight (Mass)
Gross Weight (Gross Mass)
Sound
Pressure
H / M / L / SL
Level
Sound Power Level
Outdoor Unit
Casing Color
Type
Compressor Model
Motor Output
Type
Refrigerant
Oil
Charge
Type
Refrigerant
Charge
H
Type
Fan
Motor Output
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Starting Current
Dimensions (H × W × D)
Packaged Dimensions (H × W × D)
Weight (Mass)
Gross Weight (Gross Mass)
Sound Pressure Level (H)
Sound Power Level (H)
Drawing No.
Note:
11
Cooling
2.0 (1.3 ~ 2.6)
6,800 (4,400 ~ 8,900)
1,720 (1,120 ~ 2,240)
2.7
φ 6.4
φ 9.5
φ 18.0
Both Liquid and Gas Pipes
15
12
10
g/m
Fan
Airflow Rate
kW
Btu/h
kcal/h
A
m
m
m
M
L
SL
ATX25J2V1B
ARX25J3V1B
W
Steps
A
W
%
mm
mm
kg
kg
20
ATX25J2V1B
White
9.4 (331)
7.8 (276)
6.3 (222)
5.5 (194)
9.2 (325)
7.6 (268)
6.0 (212)
4.8 (169)
Cross Flow Fan
16
5 Steps, Quiet, Auto
Right, Left, Horizontal, Downward
Removable / Washable / Mildew Proof
0.18
0.18
40
40
96.6
96.6
Microcomputer Control
283 × 770 × 198
266 × 846 × 345
7
11
39 / 33 / 25 / 22
dB
55
L
39 / 34 / 28 / 25
29.2 (1,030)
40 / 33 / 26 / 22
40 / 34 / 28 / 25
55
55
ARX25J3V1B
Ivory White
Hermetically Sealed Swing Type
1YC23AEXD
750
FVC50K
0.375
R-410A
0.74
26.2 (927)
29.2 (1,030)
Propeller
33
2.52
510
88.0
9.7 (342)
8.0 (283)
6.3 (222)
5.5 (194)
Cross Flow Fan
16
5 Steps, Quiet, Auto
Right, Left, Horizontal, Downward
Removable / Washable / Mildew Proof
0.18
0.18
40
40
96.6
96.6
Microcomputer Control
283 × 770 × 198
266 × 846 × 345
7
11
55
ARX20J3V1B
Ivory White
Hermetically Sealed Swing Type
1YC23AEXD
750
FVC50K
0.375
R-410A
0.74
W
W
A
W
%
A
mm
mm
kg
kg
dB(A)
dB
20
ATX20J2V1B
White
9.1 (321)
7.4 (261)
5.9 (208)
4.7 (166)
dB(A)
kg
m³/min
(cfm)
φ 6.4
φ 9.5
φ 18.0
Both Liquid and Gas Pipes
15
12
10
26.2 (927)
Propeller
33
2.82
550
84.8
3.52
690
85.2
3.0
550 × 658 × 275
612 × 769 × 350
28
31
46
60
3.02
650
93.6
3.7
550 × 658 × 275
612 × 769 × 350
28
31
47
61
46
60
C: 3D080717
47
61
C: 3D080718
„ The data are based on the conditions shown in the table below.
Cooling
Heating
Piping Length
Indoor ; 27°CDB / 19°CWB
Outdoor ; 35°CDB / 24°CWB
Indoor ; 20°CDB
Outdoor ; 7°CDB / 6°CWB
5m
Conversion Formulae
kcal/h = kW × 860
Btu/h = kW × 3412
cfm = m³/min × 35.3
Specifications
SiBE041010EA
Specifications
50 Hz, 230 V
Indoor Unit
Model
ATX35J2V1B
ARX35J3V1B
Outdoor Unit
Capacity
Rated (Min. ~ Max.)
Running Current (Rated)
Power Consumption
Rated (Min. ~ Max.)
Power Factor
COP Rated (Min. ~ Max.)
Liquid
Piping
Connections Gas
Drain
Heat Insulation
Max. Interunit Piping Length
Max. Interunit Height Difference
Chargeless
Amount of Additional Charge
of Refrigerant
Indoor Unit
Front Panel Color
H
Airflow Rate
Heating
3.5 (1.3 ~ 4.8)
11,900 (4,400 ~ 16,400)
3,010 (1,120 ~ 4,130)
4.7
W
980 (290 ~ 1,300)
930 (290 ~ 1,290)
%
W/W
mm
mm
mm
81.9
3.37 (4.48 ~ 2.92)
86.0
3.76 (4.48 ~ 3.72)
20
ATX35J2V1B
White
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H × W × D)
Packaged Dimensions (H × W × D)
Weight (Mass)
Gross Weight (Gross Mass)
Sound
Pressure
H / M / L / SL
Level
Sound Power Level
Outdoor Unit
Casing Color
Type
Compressor Model
Motor Output
Type
Refrigerant
Oil
Charge
Type
Refrigerant
Charge
H
Type
Fan
Motor Output
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Starting Current
Dimensions (H × W × D)
Packaged Dimensions (H × W × D)
Weight (Mass)
Gross Weight (Gross Mass)
Sound Pressure Level (H)
Sound Power Level (H)
Drawing No.
Note:
φ 6.4
φ 9.5
φ 18.0
Both Liquid and Gas Pipes
15
12
10
g/m
M
L
SL
Specifications
Cooling
3.3 (1.3 ~ 3.8)
11,300 (4,400 ~ 13,000)
2,840 (1,120 ~ 3,270)
5.2
m
m
m
Fan
Airflow Rate
kW
Btu/h
kcal/h
A
9.3 (328)
7.7 (272)
6.1 (215)
4.9 (173)
Cross Flow Fan
16
5 Steps, Quiet, Auto
Right, Left, Horizontal, Downward
Removable / Washable / Mildew Proof
W
Steps
A
W
%
10.1 (356)
8.4 (295)
6.7 (235)
5.7 (201)
0.18
40
96.6
0.18
40
96.6
Microcomputer Control
283 × 770 × 198
266 × 846 × 345
7
11
mm
mm
kg
kg
dB(A)
41 / 34 / 27 / 23
dB
58
L
W
A
W
%
A
mm
mm
kg
kg
dB(A)
dB
58
ARX35J3V1B
Ivory White
Hermetically Sealed Swing Type
1YC23AEXD
750
FVC50K
0.375
R-410A
1.0
W
kg
m³/min
(cfm)
41 / 35 / 29 / 26
27.6 (975)
24.5 (865)
Propeller
33
5.02
940
81.4
4.52
890
85.6
5.2
550 × 658 × 275
612 × 769 × 350
30
34
48
62
48
62
C: 3D080719
„ The data are based on the conditions shown in the table below.
Cooling
Heating
Piping Length
Indoor ; 27°CDB / 19°CWB
Outdoor ; 35°CDB / 24°CWB
Indoor ; 20°CDB
Outdoor ; 7°CDB / 6°CWB
5m
Conversion Formulae
kcal/h = kW × 860
Btu/h = kW × 3412
cfm = m³/min × 35.3
12
SiBE041010EA
Part 3
Printed Circuit Board
Connector Wiring Diagram
1. Indoor Unit.............................................................................................14
2. Outdoor Unit..........................................................................................16
13
Printed Circuit Board Connector Wiring Diagram
SiBE041010EA
Indoor Unit
1. Indoor Unit
Control PCB
1)
2)
3)
4)
5)
6)
7)
8)
S6
S26
S32
S200
S403
H1, H2, H3, FG
V1
JA
9) JB
JC
10)LED A
11)FU1 (F1U)
Connector for swing motor (horizontal blade)
Connector for display PCB
Connector for indoor heat exchanger thermistor
Connector for fan motor
Connector for adaptor PCB (option)
Connector for terminal board
Varistor
Address setting jumper
∗ Refer to page 97 for detail.
Fan speed setting when compressor stops for thermostat OFF
Power failure recovery function (auto-restart)
∗ Refer to page 97 for detail.
LED for service monitor (green)
Fuse (3.15 A, 250 V)
FU1
S200
LED A S32
H1
V1
H3
S26
H2
FG
S6
JA
JC
JB
S403
Caution
2P206569-1
Replace the PCB if you accidentally cut the jumpers other than JA, JB and JC.
Jumpers are necessary for electronic circuit. Improper operation may occur if you cut any of
them.
Printed Circuit Board Connector Wiring Diagram
14
Indoor Unit
SiBE041010EA
Display PCB
1) S27
2) SW1 (S1W)
3) LED1 (H1P)
4) LED2 (H2P)
5) RTH1 (R1T)
Connector for control PCB
Forced cooling operation [ON/OFF] button
∗ Refer to page 95 for detail.
LED for operation (green)
LED for timer (yellow)
Room temperature thermistor
S27
SW1
LED2 LED1
(Solder side)
RTH1
3P206563-1
15
Printed Circuit Board Connector Wiring Diagram
SiBE041010EA
Outdoor Unit
2. Outdoor Unit
Main PCB
1)
2)
3)
4)
5)
6)
S10
S20
S40
S70
S80
S90
Connector for filter PCB
Connector for electronic expansion valve coil
Connector for overload protector
Connector for fan motor
Connector for four way valve coil
Connector for thermistors
(outdoor temperature, outdoor heat exchanger, discharge pipe)
Connector for filter PCB
Connector for reactor
Connector for compressor
Fuse (3.15 A, 250 V)
LED for service monitor (green)
Varistor
Jumper for improvement of defrost performance
∗ Refer to page 97 for detail.
7) HL3, HN3
8) HR2
9) U, V, W
10)FU1, FU2
11)LED A
12)V1
13)J5
U VW
J5
S10
S90
LED A
S70
S40
S20
HL3
FU1
V1
HN3
S80
FU2
HR2
Caution
2P206705-1
2P206705-3
Replace the PCB if you accidentally cut any jumper other than J5.
Jumpers are necessary for electronic circuit. Improper operation may occur if you cut any of
them.
Printed Circuit Board Connector Wiring Diagram
16
Outdoor Unit
SiBE041010EA
Filter PCB
1)
2)
3)
4)
5)
6)
7)
S11
AC1, AC2, S
E1, E2
HL2, HN2
HR1
FU3
V2, V3
Connector for main PCB
Connector for terminal board
Terminal for earth wire
Connector for main PCB
Connector for reactor
Fuse (20 A, 250 V)
Varistor
E1, E2
HR1
HN2
HL2
V2
AC2
V3
AC1
S11
S
FU3
3P206706-1
17
Printed Circuit Board Connector Wiring Diagram
SiBE041010EA
Part 4
Function and Control
1. Main Functions......................................................................................19
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
1.12
Temperature Control ..............................................................................19
Frequency Principle................................................................................19
Airflow Direction Control.........................................................................21
Fan Speed Control for Indoor Unit .........................................................22
Program Dry Operation ..........................................................................23
Automatic Operation...............................................................................24
Thermostat Control.................................................................................25
NIGHT SET Mode ..................................................................................26
ECONO Operation .................................................................................26
Inverter POWERFUL Operation .............................................................27
Clock Setting ..........................................................................................27
Other Functions......................................................................................28
2. Function of Thermistor ..........................................................................29
3. Control Specification .............................................................................30
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
Function and Control
Mode Hierarchy ......................................................................................30
Frequency Control..................................................................................30
Controls at Mode Changing / Start-up....................................................32
Discharge Pipe Temperature Control.....................................................33
Input Current Control..............................................................................34
Freeze-up Protection Control .................................................................35
Heating Peak-cut Control .......................................................................35
Outdoor Fan Control...............................................................................36
Liquid Compression Protection Function................................................36
Defrost Control .......................................................................................37
Electronic Expansion Valve Control .......................................................38
Malfunctions ...........................................................................................41
18
Main Functions
SiBE041010EA
1. Main Functions
1.1
Temperature Control
Definitions of
Temperatures
The definitions of temperatures are classified as following.
Š
Š
Š
Š
Room temperature: temperature of lower part of the room
Set temperature: temperature set by remote controller
Room thermistor temperature: temperature detected by room temperature thermistor
Target temperature: temperature determined by microcomputer
Target temperature
Room thermistor temperature
Set temperature
Room temperature
(R12321)
Temperature
Control
1.2
Frequency Principle
Main Control
Parameters
Additional
Control
Parameters
Inverter Principle
19
The temperature of the room is detected by the room temperature thermistor. However, there is
a difference between the “temperature detected by room temperature thermistor” and the
“temperature of lower part of the room”, depending on the type of the indoor unit or installation
condition. Practically, the temperature control is done by the “target temperature appropriately
adjusted for the indoor unit” and the “temperature detected by room temperature thermistor”.
The frequency of the compressor is controlled by the following 2 parameters:
„ The load condition of the operating indoor unit
„ The difference between the room thermistor temperature and the target temperature
The target frequency is adapted by additional parameters in the following cases:
„ Frequency restrictions
„ Initial settings
„ Forced cooling operation
To regulate the capacity, a frequency control is needed. The inverter makes it possible to alter
the rotation speed of the compressor. The following table explains the conversion principle:
Phase
Description
1
2
The supplied AC power source is converted into the DC power source for the present.
The DC power source is reconverted into the three phase AC power source with variable
frequency.
„ When the frequency increases, the rotation speed of the compressor increases resulting
in an increased refrigerant circulation. This leads to a higher amount of the heat
exchange per unit.
„ When the frequency decreases, the rotation speed of the compressor decreases
resulting in a decreased refrigerant circulation. This leads to a lower amount of the heat
exchange per unit.
Function and Control
SiBE041010EA
Drawing of
Inverter
Main Functions
The following drawing shows a schematic view of the inverter principle:
Refrigerant circulation rate (high)
AC
power
Amount of heat
exchanged air (small)
DC
power
high speed
Amount of heat
exchanged air (large)
high f
low f
low speed
50 Hz
freq=
constant 60 Hz freq=variable
Amount of heat
exchanged air (large)
Amount of heat
exchanged air (small)
capacity=
variable
Refrigerant circulation rate (low)
Inverter Features
(R2812)
The inverter provides the following features:
„ The regulating capacity can be changed according to the changes in the outdoor
„
„
„
„
Frequency Limits
temperature and cooling / heating load.
Quick heating and quick cooling
The rotation speed of the compressor is increased when starting the heating (or cooling).
This enables to reach the set temperature quickly.
Even during extreme cold weather, high capacity is achieved. It is maintained even when the
outdoor temperature is 2°C.
Comfortable air conditioning
A fine adjustment is integrated to keep the room temperature constant.
Energy saving heating and cooling
Once the set temperature is reached, the energy saving operation enables to maintain the
room temperature at low power.
The following functions regulate the minimum and maximum frequency:
Frequency
Low
High
Forced Cooling
Operation
Function and Control
Functions
„ Four way valve operation compensation. Refer to page 32.
„
„
„
„
„
„
Compressor protection function. Refer to page 33.
Discharge pipe temperature control. Refer to page 33.
Input current control. Refer to page 34.
Freeze-up protection control. Refer to page 35.
Heating peak-cut control. Refer to page 35.
Defrost control. Refer to page 37.
Refer to page 95 for detail.
20
Main Functions
1.3
SiBE041010EA
Airflow Direction Control
Power-Airflow
Flap
The large flap sends a large volume of air downward to the floor and provides an optimum
control in cooling, dry, and heating operation.
<Cooling / Dry>
During cooling or dry operation, the flap retracts into the indoor unit. Then, cool air can be blown
far and distributed all over the room.
<Heating>
During heating operation, the large flap directs airflow downward to spread the warm air to the
entire room.
Wide-Angle
Louvers
The louvers, made of elastic synthetic resin, provide a wide range of airflow that guarantees
comfortable air distribution.
Auto-Swing
The following table explains the auto-swing process for cooling, dry, fan, and heating:
Vertical Swing (up and down)
Cooling / Dry / Fan
Heating
5˚
15˚
45˚
COMFORT
AIRFLOW
Operation
(R11256)
45˚
(R11257)
The vertical swing flap is controlled not to blow the air directly at the people in the room.
Cooling / Dry
Heating
0˚
(R11259)
21
50˚
(R11258)
Function and Control
SiBE041010EA
1.4
Main Functions
Fan Speed Control for Indoor Unit
Outline
Phase control and fan speed control contains 9 steps: LLL, LL, SL, L, ML, M, MH, H, and HH.
The airflow rate can be automatically controlled depending on the difference between the room
thermistor temperature and the target temperature. This is done through phase control and Hall
IC control.
For more information about Hall IC, refer to the troubleshooting for fan motor on page 54.
Automatic Fan
Speed Control
In automatic fan speed operation, the step “SL” is not available.
Step
Cooling
Heating
LLL
LL
L
ML
M
MH
H
HH (POWERFUL)
(R6834)
(R11681)
= The airflow rate is automatically controlled within this range when the [FAN] setting
button is set to automatic.
<Cooling>
The following drawing explains the principle of fan speed control for cooling.
Room thermistor temperature – target temperature
Fan speed
MH*
+2.5°C
M
+1.5°C
ML
+0.5°C
L
+3°C
+2°C
+1°C
(R14588)
*The upper limit is M tap in 30 minutes from the operation start.
<Heating>
In heating operation, the fan speed is regulated according to the indoor heat exchanger
temperature and the difference between the room thermistor temperature and the target
temperature.
Note:
COMFORT
AIRFLOW
Operation
Function and Control
1. During POWERFUL operation, the fan rotates at H tap + 80 rpm.
2. The fan stops during defrost control.
„ The fan speed is controlled automatically.
„ The latest command has the priority between POWERFUL and COMFORT AIRFLOW.
22
Main Functions
1.5
SiBE041010EA
Program Dry Operation
Outline
Program dry operation removes humidity while preventing the room temperature from lowering.
Since the microcomputer controls both the temperature and airflow rate, the temperature
adjustment and [FAN] setting buttons are inoperable.
Detail
The microcomputer automatically sets the temperature and airflow rate. The difference between
the room thermistor temperature at start-up and the target temperature is divided into two
zones. Then, the unit operates in an appropriate capacity for each zone to maintain the
temperature and humidity at a comfortable level.
Room thermistor
temperature at start-up
Target temperature
X
Thermostat OFF point
Y
Thermostat ON point
Z
X – 2.5ºC
X – 0.5ºC
or
Y + 0.5ºC (zone B)
continues for 10 min.
X – 2.0ºC
X – 0.5ºC
or
Y + 0.5ºC (zone B)
continues for 10 min.
X – 2.0ºC
X – 0.5ºC = 17.5ºC
or
Y + 0.5ºC (zone B)
continues for 10 min.
24ºC or more
Room thermistor
temperature at start-up
23.5ºC
~
18ºC
17.5ºC
18ºC
~
X
Zone C = Thermostat ON
Zone B
Z
Zone B
Y
+0.5ºC
Zone A = Thermostat OFF
(R11581)
23
Function and Control
SiBE041010EA
1.6
Main Functions
Automatic Operation
Outline
Detail
Automatic Cooling / Heating Function
When the automatic operation is selected with the remote controller, the microcomputer
automatically determines the operation mode as cooling or heating according to the room
temperature and the set temperature at start-up.
The unit automatically switches the operation mode to maintain the room temperature at the set
temperature.
Ts: set temperature (set by remote controller)
Tt: target temperature (determined by microcomputer)
Tr: room thermistor temperature (detected by room temperature thermistor)
C: correction value
1. The set temperature determines the target temperature.
Ts = 18 ~ 30°C
2. The target temperature is calculated as;
Tt = Ts + C
where C = 0°C
3. The thermostat ON/OFF point and operation mode switching point are as follows.
(1) Heating → Cooling switching point:
Tr ≥ Tt + 2.5°C
(2) Cooling → Heating switching point:
Tr < Tt – 2.5°C
(3) The thermostat ON/OFF point is the same as the ON/OFF point of cooling or heating
operation.
4. During initial operation
Tr ≥ Ts : Cooling operation
Tr < Ts : Heating operation
Cooling Operation
Target temperature + 2.5˚C
Target temperature – 2.0˚C
= Thermostat OFF
Target temperature + 1.5˚C
= Thermostat OFF
Target temperature – 2.5˚C
Heating Operation
(R11893)
Ex: When the target temperature is 25°C
Cooling → 23°C: Thermostat OFF → 22°C: Switch to heating
Heating → 26.5°C: Thermostat OFF → 27.5°C: Switch to cooling
Function and Control
24
Main Functions
1.7
SiBE041010EA
Thermostat Control
Outline
Thermostat control is based on the difference between the room thermistor temperature and the
target temperature.
Detail
Thermostat OFF Condition
Š The temperature difference is in the zone A.
Thermostat ON Condition
Š The temperature difference returns to the zone C after being in the zone A.
Š The system resumes from defrost control in any zones except A.
Š The operation turns on in any zones except A.
Š The monitoring time has passed while the temperature difference is in the zone B.
(Cooling / Dry: 10 minutes, Heating: 10 seconds)
<Cooling / Dry>
ON
Room thermistor temperature – target temperature
Cooling : –0.5˚C
Dry : –0.5˚C
C
–1.5˚C
B
Cooling : –2.0˚C
Dry : –2.5 ~ –2.0˚C
A
OFF
(R12319)
<Heating>
Room thermistor temperature – target temperature
OFF
A
1.5˚C
B
1.0˚C
C
0˚C
ON
(R12320)
Refer to “Temperature Control” on page 19 for detail.
25
Function and Control
SiBE041010EA
1.8
Main Functions
NIGHT SET Mode
Outline
When the OFF TIMER is set, the NIGHT SET Mode is automatically activated. The NIGHT SET
Mode keeps the airflow rate setting.
Detail
The NIGHT SET Mode continues operation at the target temperature for the first one hour, then
automatically raises the target temperature slightly in the case of cooling, or lowers it slightly in
the case of heating. This prevents excessive cooling in summer and excessive heating in winter
to ensure comfortable sleeping conditions, and also conserves electricity.
<Cooling>
0.5˚C
Target temperature
Operation stops
at the set hours
1 hour
TIMER operation
NIGHT SET Mode ON
+0.5˚C
temperature shift
(R18917)
<Heating>
Target temperature
2˚C
1 hour
TIMER operation
NIGHT SET Mode ON
1.9
–2˚C
temperature shift
(R18985)
ECONO Operation
Outline
ECONO operation reduces the maximum operating current and the power consumption.
This operation is particularly convenient for energy-saving-oriented users. It is also a major
bonus for those whose breaker capacities do not allow the use of multiple electrical devices and
air conditioners.
It is easily activated from the wireless remote controller by pushing the [ECONO] button.
Detail
„ When this function is activated, the maximum capacity also decreases.
„ The remote controller can send the ECONO command when the unit is in cooling, heating,
dry, or automatic operation. This function can only be set when the unit is running. Pressing
the [ON/OFF] button on the remote controller cancels the function.
„ This function and POWERFUL operation cannot be used at the same time. The latest
command has the priority.
Power
consumption
and current
Maximum during normal operation
Normal
Maximum during ECONO operation
ECONO Operation
Time
(R9288)
Function and Control
26
Main Functions
SiBE041010EA
1.10 Inverter POWERFUL Operation
Outline
In order to exploit the cooling and heating capacity to full extent, operate the air conditioner by
increasing the indoor fan rotating speed and the compressor frequency.
Detail
When the [POWERFUL] button is pressed, the fan speed and target temperature are converted
to the following states for 20 minutes.
Operation mode
Fan speed
Target temperature
COOL
DRY
H tap + A rpm
Dry rotating speed + A rpm
18°C
Lowered by 2.5°C
HEAT
FAN
H tap + A rpm
H tap + A rpm
31°C
—
AUTO
Same as cooling / heating in
POWERFUL operation
The target temperature is
kept unchanged.
A = 80 rpm
Ex: POWERFUL operation in cooling
Target temp.
It should be the lower limit of
cooling temperature.
18˚C
It counts 20 minutes. also
in the remote controller.
POWERFUL
ON
POWERFUL
OFF
Fan
A rpm
H tap
20 minutes
Ending condition: "or" in 1 to 3
1. After the lapse of 20 minutes.
2. Operation OFF
3. POWERFUL operation is OFF.
Set tap
(R13571)
1.11 Clock Setting
ARC433 Series
The clock can be set by taking the following steps:
1. Press the [CLOCK] button.
→
is displayed and
blinks.
2. Press the [TIMER] or button to set the clock to the present time.
Holding down the [TIMER] or button increases or decreases the time display rapidly.
3. Press the [CLOCK] button again.
→
blinks and clock setting is completed.
TIMER button
CLOCK button
(R18286)
27
Function and Control
SiBE041010EA
Main Functions
1.12 Other Functions
1.12.1 Hot-Start Function
In order to prevent the cold air blast that normally comes when heating operation is started, the
temperature of the indoor heat exchanger is detected, and the airflow is either stopped or made
very weak thereby carrying out comfortable heating of the room.
*The cold air blast is also prevented using similar control when the defrost control starts or when
the thermostat is turned ON.
1.12.2 Signal Receiving Sign
When the indoor unit receives a signal from the remote controller, the unit emits a signal
receiving sound.
1.12.3 Indoor Unit [ON/OFF] Button
An [ON/OFF] button is provided on the display of the unit.
„ Press the [ON/OFF] button once to start operation. Press once again to stop it.
„ The [ON/OFF] button is useful when the remote controller is missing or the battery has run
out.
„ The operation mode refers to the following table.
Operation mode
AUTO
Temperature setting
25ºC
Airflow rate
Automatic
ON/OFF button
(R8435)
<Forced cooling operation>
Forced cooling operation can be started by pressing the [ON/OFF] button for 5 to 9 seconds
while the unit is not operating.
Refer to page 95 for detail.
Note:
When the [ON/OFF] button is pressed for 10 seconds or more, the forced cooling operation is
stopped.
1.12.4 Titanium Apatite Photocatalytic Air-Purifying Filter
This filter combines the Air-Purifying Filter and Titanium Apatite Photocatalytic Deodorizing
Filter as a single highly effective filter. The filter traps microscopic particles, decomposes odors
and even deactivates bacteria and viruses. It lasts for 3 years without replacement if washed
about once every 6 months.
1.12.5 Auto-restart Function
If a power failure (including one for just a moment) occurs during the operation, the operation
restarts automatically when the power is restored in the same condition as before the power
failure.
Note:
Function and Control
It takes 3 minutes to restart the operation because the 3-minute standby function is activated.
28
Function of Thermistor
SiBE041010EA
2. Function of Thermistor
Electronic
expansion valve
(1)
(3)
Four way valve
(2)
Compressor
(R14247)
(1) Outdoor Heat
Exchanger
Thermistor
1. The outdoor heat exchanger thermistor is used for controlling the target discharge pipe
temperature. The system sets the target discharge pipe temperature according to the
outdoor and indoor heat exchanger temperature, and controls the electronic expansion valve
opening so that the target discharge pipe temperature can be obtained.
2. In cooling operation, the outdoor heat exchanger thermistor is used for detecting the
disconnection of the discharge pipe thermistor. When the discharge pipe temperature drops
below the outdoor heat exchanger temperature by more than a certain value, the discharge
pipe thermistor is judged as disconnected.
3. In cooling operation, the outdoor heat exchanger thermistor is used for high pressure
protection.
(2) Discharge
Pipe Thermistor
1. The discharge pipe thermistor is used for controlling discharge pipe temperature. If the
discharge pipe temperature (used in place of the inner temperature of the compressor) rises
abnormally, the operating frequency becomes lower or the operation halts.
2. The discharge pipe thermistor is used for detecting disconnection of the discharge pipe
thermistor.
(3) Indoor Heat
Exchanger
Thermistor
1. The indoor heat exchanger thermistor is used for controlling the target discharge pipe
temperature. The system sets the target discharge pipe temperature according to the
outdoor and indoor heat exchanger temperature, and controls the electronic expansion valve
opening so that the target discharge pipe temperature can be obtained.
2. In cooling operation, the indoor heat exchanger thermistor is used for freeze-up protection
control. If the indoor heat exchanger temperature drops abnormally, the operating frequency
becomes lower or the operation halts.
3. In heating operation, the indoor heat exchanger thermistor is used for detecting the
disconnection of the discharge pipe thermistor. When the discharge pipe temperature drops
below the indoor heat exchanger temperature by more than a certain value, the discharge
pipe thermistor is judged as disconnected.
29
Function and Control
SiBE041010EA
Control Specification
3. Control Specification
3.1
Mode Hierarchy
Outline
The air conditioner control has normal operation mode, forced operation mode, and power
transistor test mode for installation and servicing.
Detail
Air conditioner control mode
Forced operation mode
Forced cooling operation (for pump down operation)
Power transistor test mode
Normal operation mode
Fan
Cooling (includes drying)
Heating
Heating
Defrosting
Stop (indoor unit: OFF)
Preheating operation
Discharging from capacitor
Stop
(R17533)
Note:
3.2
Unless specified otherwise, a dry operation command is regarded as cooling operation.
Frequency Control
Outline
Frequency is determined according to the difference between the room thermistor temperature
and the target temperature.
When the shift of the frequency is less than zero (∆F<0) by PI control,
the target frequency is used as the command frequency.
Dropping function
Input current control, etc.
Upper limit frequency
FMAX
Command frequency
Limit frequency
Initial frequency
PI control
Defrost control
Lower limit frequency
FMIN
Upper limit function
Compressor protection function
Skip control
Target frequency
Lower limit function
Four way valve operation compensation, etc.
(R18023)
Detail
Function and Control
How to Determine Frequency
The compressor’s frequency is determined by taking the following steps.
30
Control Specification
SiBE041010EA
1. Determine command frequency
Š Command frequency is determined in the following order of priority.
1. Limiting defrost control time
2. Forced cooling
3. Indoor frequency command
2. Determine upper limit frequency
Š The minimum value is set as an upper limit frequency among the frequency upper limits of
the following functions:
Compressor protection, input current, discharge pipe temperature, heating peak-cut, freezeup protection, defrost.
3. Determine lower limit frequency
Š The maximum value is set as a lower limit frequency among the frequency lower limits of the
following functions:
Four way valve operation compensation, draft prevention, pressure difference upkeep.
4. Determine prohibited frequency
Š There is a certain prohibited frequency such as a power supply frequency.
Indoor Frequency Command (∆D signal)
The difference between the room thermistor temperature and the target temperature is taken as
the “∆D signal” and is used for frequency command.
Temperature
difference
∆D
signal
Temperature
difference
∆D
signal
Temperature
difference
∆D
signal
Temperature
difference
∆D
signal
–2.0
0
4
2.0
8
4.0
C
–1.5
∗Th
OFF
1
0.5
5
2.5
9
4.5
D
–1.0
–0.5
2
3
1.0
1.5
6
7
3.0
3.5
A
B
5.0
5.5
E
F
∗Th OFF = Thermostat OFF
Frequency Initial Setting
When starting the compressor, the frequency is initialized according to the ∆D value and the Q
value of the indoor unit.
Q value: Indoor unit output determined from indoor unit volume, airflow rate and other factors.
PI Control (Determine Frequency Up / Down by ∆D Signal)
1. P control
The ∆D value is calculated in each sampling time (20 seconds), and the frequency is
adjusted according to its difference from the frequency previously calculated.
2. I control
If the operating frequency does not change for more than a certain fixed time, the frequency
is adjusted according to the ∆D value.
When the ∆D value is low, the frequency is lowered.
When the ∆D value is high, the frequency is increased.
3. Frequency management when other controls are functioning
Š When frequency is dropping;
Frequency management is carried out only when the frequency drops.
Š For limiting lower limit
Frequency management is carried out only when the frequency rises.
4. Upper and lower limit of frequency by PI control
The frequency upper and lower limits are set according to the command of the indoor unit.
When the indoor or outdoor unit quiet operation command comes from the indoor unit, the
upper limit frequency is lower than the usual setting.
31
Function and Control
SiBE041010EA
3.3
Control Specification
Controls at Mode Changing / Start-up
3.3.1 Preheating Control
Outline
The inverter operation in open phase starts with the conditions of the preheating command from
the indoor unit, the outdoor temperature, and the discharge pipe temperature.
Detail
Outdoor temperature ≥ A°C → Control I
Outdoor temperature < A°C → Control II
Control I
Š ON condition
Discharge pipe temperature < B°C
Š OFF condition
Discharge pipe temperature > C°C
Radiation fin temperature ≥ 90°C
Control II
Š ON condition
Discharge pipe temperature < D°C
Š OFF condition
Discharge pipe temperature > E°C
Radiation fin temperature ≥ 90°C
RX20/25/35JV1B, ARX20/25/35JV1B
RX20/25/35J3V1B, ARX20/25/35J3V1B
A (°C)
7
B (°C)
10
C (°C)
12
D (°C)
20
E (°C)
22
–2.5
0
2
10
12
3.3.2 Four Way Valve Switching
Outline
In heating operation, current is conducted, and in cooling operation and defrost control, current
is not conducted. In order to eliminate the switching sound as the four way valve coil switches
from ON to OFF when the heating is stopped, the OFF delay switch of the four way valve is
carried out.
Detail
OFF delay switch of four way valve:
The four way valve coil is energized for 160 seconds after the operation is stopped.
3.3.3 Four Way Valve Operation Compensation
Outline
At the beginning of the operation as the four way valve is switched, the pressure difference to
activate the four way valve is acquired by having output frequency which is more than a certain
fixed frequency, for a certain fixed time.
Detail
Starting Conditions
1. When the compressor starts and the four way valve switches from OFF to ON
2. When the four way valve switches from ON to OFF during operation
3. When the compressor starts after resetting
4. When the compressor starts after the fault of four way valve switching
The lower limit of frequency keeps A Hz for B seconds with any conditions 1 through 4 above.
Function and Control
A (Hz)
62
B (seconds)
50
32
Control Specification
SiBE041010EA
3.3.4 3-minute Standby
Turning on the compressor is prohibited for 3 minutes after turning it off.
(Except when defrosting.)
3.3.5 Compressor Protection Function
When turning the compressor from OFF to ON, the upper limit of frequency is set as follows.
(The function is not activated when defrosting.)
(Hz)
Frequency
C
B
A
D
E
(sec.)
Time
F
(R13528)
3.4
Outline
A (Hz)
58
B (Hz)
C (Hz)
72
90
D (seconds)
E (seconds)
180
180
F (seconds)
10
Discharge Pipe Temperature Control
The discharge pipe temperature is used as the internal temperature of the compressor. If the
discharge pipe temperature rises above a certain level, the upper limit of frequency is set to
keep the discharge pipe temperature from rising further.
Detail
Stop zone
A˚C
B˚C
Dropping zone
C˚C
Keep zone
D˚C
Discharge pipe
temperature
Zone
Stop zone
33
Up zone
Reset zone
E˚C
(R14642)
Control
When the temperature reaches the stop zone, the compressor stops.
Dropping zone
Keep zone
The upper limit of frequency decreases.
The upper limit of frequency is kept.
Up zone
Reset zone
The upper limit of frequency increases.
The upper limit of frequency is canceled.
A (ºC)
110
B (ºC)
C (ºC)
105
101
D (ºC)
E (ºC)
99
97
Function and Control
SiBE041010EA
3.5
Control Specification
Input Current Control
Outline
The microcomputer calculates the input current while the compressor is running, and sets the
frequency upper limit from the input current.
In case of heat pump models, this control which is the upper limit control of the frequency takes
priority over the lower limit of control of four way valve operation compensation.
Detail
Compressor Stop
(A)
Stop Zone
A
Dropping Zone
B
Keep Zone
C
Input current
Reset Zone
(R14643)
Frequency control in each zone
Stop zone
Š After 2.5 seconds in this zone, the compressor is stopped.
Dropping zone
Š The upper limit of the compressor frequency is defined as operation frequency – 2 Hz.
Š After this, the output frequency is lowered by 2 Hz every second until it reaches the keep
zone.
Keep zone
Š The present maximum frequency goes on.
Reset zone
Š Limit of the frequency is canceled.
20/25 class
Cooling
Heating
A (A)
B (A)
C (A)
35 class
Cooling
Heating
Normal mode
14
6.0
14
6.75
14
6.5
14
7.75
ECONO mode
2.75
2.75
2.75
2.75
Normal mode
ECONO mode
5.25
2.0
6.0
2.0
5.75
2.0
7.0
2.0
Limitation of current dropping and stop value according to the outdoor temperature
Š The current drops when outdoor temperature becomes higher than a certain level
(depending on the model).
Function and Control
34
Control Specification
3.6
SiBE041010EA
Freeze-up Protection Control
Outline
During cooling operation, the signal sent from the indoor unit controls the operating frequency
limitation and prevents freezing of the indoor heat exchanger. (The signal from the indoor unit is
divided into zones.)
Detail
The operating frequency limitation is judged with the indoor heat exchanger temperature.
Indoor heat exchanger
thermistor temperature
13˚C
Reset zone
A˚C
Up zone
B˚C
Keep zone
C˚C
Dropping zone
0˚C
Stop zone
(R14718)
3.7
Outline
A (°C)
B (°C)
C (°C)
11
9
7
Heating Peak-cut Control
During heating operation, the indoor heat exchanger temperature determines the frequency
upper limit to prevent abnormal high pressure.
Detail
Stop zone
A˚C
B˚C
Dropping zone
C˚C
Keep zone
D˚C
Up zone
Reset zone
Indoor heat exchanger
thermistor temperature
Zone
Stop zone
35
(R14645)
Control
When the temperature reaches the stop zone, the compressor stops.
Dropping zone
Keep zone
The upper limit of frequency decreases.
The upper limit of frequency is kept.
Up zone
Reset zone
The upper limit of frequency increases.
The upper limit of frequency is canceled.
A (°C)
65
B (°C)
55
E˚C
C (°C)
52
D (°C)
50
E (°C)
45
Function and Control
SiBE041010EA
3.8
Control Specification
Outdoor Fan Control
1. Fan ON control to cool down the electrical box
The outdoor fan is turned ON when the electrical box temperature is high while the compressor
is OFF.
2. Fan OFF control during defrosting
The outdoor fan is turned OFF during defrosting.
3. Fan OFF delay when stopped
The outdoor fan is turned OFF 70 seconds after the compressor stops.
4. Fan speed control for pressure difference upkeep
The rotation speed of the outdoor fan is controlled for keeping the pressure difference during
cooling operation with low outdoor temperature.
Š When the pressure difference is low, the rotation speed of the outdoor fan is reduced.
Š When the pressure difference is high, the rotation speed of the outdoor fan is controlled as
well as normal operation.
5. Fan speed control during forced cooling operation
The outdoor fan is controlled as well as normal operation during forced cooling operation.
6. Fan speed control during POWERFUL operation
The rotation speed of the outdoor fan is increased during POWERFUL operation.
7. Fan speed control during indoor / outdoor unit quiet operation
The rotation speed of the outdoor fan is reduced by the command of the indoor / outdoor unit
quiet operation.
8. Fan ON/OFF control when operation starts / stops
The outdoor fan is turned ON when the operation starts. The outdoor fan is turned OFF when
the operation stops.
3.9
Liquid Compression Protection Function
Outline
In order to obtain the dependability of the compressor, the compressor is stopped according to
the outdoor temperature and the outdoor heat exchanger temperature.
Detail
Operation stops depending on the outdoor temperature.
Compressor turns off under the conditions that the system is in cooling operation and outdoor
temperature is below 0°C.
Function and Control
36
Control Specification
SiBE041010EA
3.10 Defrost Control
Outline
Defrosting is carried out by the cooling cycle (reverse cycle). The defrosting time or outdoor
heat exchanger temperature must be more than a certain value to finish defrosting.
Detail
Conditions for Starting Defrost
„ The starting conditions are determined with the outdoor temperature and the outdoor heat
exchanger temperature.
„ The system is in heating operation.
„ The compressor operates for 6 minutes.
„ More than A minutes of accumulated time pass after the start of the operation, or ending the
previous defrosting.
Conditions for Canceling Defrost
The judgment is made with the outdoor heat exchanger temperature. (B°C)
D Hz
C Hz
PI control
Frequency
0 Hz
0 Hz
F sec.
E sec.
Compressor
Four way valve
G sec.
H sec.
ON
OFF
ON
OFF
5 sec.
5 sec.
Fan
ON
OFF
J pulse
Electronic expansion
valve opening
L pulse
M pulse
K pulse
Initial opening
(R18152)
20/25 class
35 class
28
4 ~ 22
28
4 ~ 22
C (Hz)
D (Hz)
68
80
72
84
E (seconds)
F (seconds)
80
60
80
60
G (seconds)
H (seconds)
510
100
510
70
J (pulse)
K (pulse)
450
400
450
400
L (pulse)
M (pulse)
430
450
430
450
A (minutes)
B (°C)
37
Function and Control
SiBE041010EA
Control Specification
3.11 Electronic Expansion Valve Control
During target discharge pipe temperature control
When the frequency changes under target discharge
pipe temperature control
When the disconnection of the discharge pipe
thermistor is ascertained
When the frequency changes under the control for
disconnection of the discharge pipe thermistor
Under defrost control
The followings are the examples of electronic expansion valve control which function in each
operation mode.
When the frequency changes under starting control
Detail
When the operation starts
The following items are included in the electronic expansion valve control.
Electronic expansion valve is fully closed
1. Electronic expansion valve is fully closed when turning on the power.
2. Pressure equalizing control
Open Control
1. Electronic expansion valve control when starting operation
2. Electronic expansion valve control when the frequency changes
3. Electronic expansion valve control for defrosting
4. Electronic expansion valve control when the discharge pipe temperature is abnormally high
5. Electronic expansion valve control when the discharge pipe thermistor is disconnected
Feedback Control
Target discharge pipe temperature control
When the power turns on or when the compressor
stops
Outline
Starting control
−
h
−
−
−
−
−
−
Control when the frequency changes
−
−
h
−
h
−
−
−
Target discharge pipe temperature control
−
−
−
h
−
−
−
−
Control for disconnection of the discharge
pipe thermistor
−
−
−
−
−
h
h
−
High discharge pipe temperature control
−
h
h
h
h
−
−
−
Pressure equalizing control
h
−
−
−
−
−
−
−
Opening limit control
−
h
h
h
h
h
h
−
Starting control
−
h
−
−
−
−
−
−
Control when the frequency changes
−
−
h
−
h
−
−
−
Target discharge pipe temperature control
−
−
−
h
−
−
−
−
Control for disconnection of the discharge
pipe thermistor
−
−
−
−
−
h
h
−
High discharge pipe temperature control
−
h
h
h
h
−
−
−
Defrost control
−
−
−
−
−
−
−
h
Pressure equalizing control
h
−
−
−
−
−
−
−
Opening limit control
−
h
h
h
h
h
h
−
h : Available
— : Not available
Cooling
Heating
Function and Control
38
Control Specification
SiBE041010EA
3.11.1 Fully Closing with Power ON
The electronic expansion valve is initialized when turning on the power. The opening position is
set and the pressure equalization is developed.
3.11.2 Pressure Equalizing Control
When the compressor is stopped, the pressure equalizing control is activated. The electronic
expansion valve opens, and develops the pressure equalization.
3.11.3 Opening Limit Control
The maximum and minimum opening of the electronic expansion valve are limited.
Maximum opening pulse
470
Minimum opening pulse
52
The electronic expansion valve is fully closed when cooling operation stops, and is opened at a
fixed degree during defrosting.
3.11.4 Starting Operation Control
The electronic expansion valve opening is controlled when the operation starts, and prevents
superheating or liquid compression.
3.11.5 Control when the Frequency Changes
When the target discharge pipe temperature control is active, if the target frequency is changed
to a specified value in a certain time period, the target discharge pipe temperature control is
canceled and the target opening of the electronic expansion valve is changed according to the
shift.
3.11.6 High Discharge Pipe Temperature Control
When the compressor is operating, if the discharge pipe temperature exceeds a certain value,
the electronic expansion valve opens and the refrigerant runs to the low pressure side. This
procedure lowers the discharge pipe temperature.
39
Function and Control
SiBE041010EA
Control Specification
3.11.7 Control for Disconnection of the Discharge Pipe Thermistor
Outline
The disconnection of the discharge pipe thermistor is detected by comparing the discharge pipe
temperature with the condensation temperature. If the discharge pipe thermistor is
disconnected, the electronic expansion valve opens according to the outdoor temperature and
the operation frequency, operates for a specified time, and then stops.
After 3 minutes, the operation restarts and checks if the discharge pipe thermistor is
disconnected. If the discharge pipe thermistor is disconnected, the system stops after operating
for a specified time.
If the disconnection is detected repeatedly, the system is shut down. When the compressor runs
for 60 minutes without any error, the error counter is reset.
Detail
When the starting control (cooling: A seconds, heating: B seconds) finishes, the detection timer
for disconnection of the discharge pipe thermistor (C seconds) starts. When the timer is over,
the following adjustment is made.
When the following condition is fulfilled, the discharge pipe thermistor disconnection is
ascertained.
<Cooling>
Discharge pipe temperature + 6°C < outdoor heat exchanger temperature
<Heating>
Discharge pipe temperature + 6°C < indoor heat exchanger temperature
A (seconds)
10
B (seconds)
C (seconds)
120
720
Adjustment when the thermistor is disconnected
When the disconnection is ascertained, the compressor continues operation for 9 minutes and
then stops.
If the compressor stops repeatedly, the system is shut down.
3.11.8 Target Discharge Pipe Temperature Control
The target discharge pipe temperature is obtained from the indoor and outdoor heat exchanger
temperature, and the electronic expansion valve opening is adjusted so that the actual
discharge pipe temperature becomes close to the target discharge pipe temperature. (Indirect
SH (superheating) control using the discharge pipe temperature)
The target discharge pipe
temperature is set as to become
the aim SH.
SC
(Subcool)
The inclination does not change
depending on the operating condition.
SH
(Superheat)
(R18921)
The electronic expansion valve opening and the target discharge pipe temperature are adjusted
every 20 seconds. The target discharge pipe temperature is controlled by indoor heat
exchanger temperature and outdoor heat exchanger temperature. The opening degree of the
electronic expansion valve is controlled by the followings.
Š Target discharge pipe temperature
Š Actual discharge pipe temperature
Š Previous discharge pipe temperature
Function and Control
40
Control Specification
SiBE041010EA
3.12 Malfunctions
3.12.1 Sensor Malfunction Detection
Sensor malfunction may occur in the thermistor.
Relating to Thermistor Malfunction
1. Outdoor heat exchanger thermistor
2. Discharge pipe thermistor
3. Radiation fin thermistor
4. Outdoor temperature thermistor
3.12.2 Detection of Overcurrent and Overload
Outline
An excessive output current is detected and the OL temperature is observed to protect the
compressor.
Detail
„ If the OL (compressor head) temperature exceeds 120°C, the system shuts down the
compressor.
„ If the inverter current exceeds 14 A, the system shuts down the compressor.
3.12.3 Refrigerant Shortage Control
Outline
I: Detecting by power consumption
If the power consumption is below the specified value and the frequency is higher than the
specified frequency, it is regarded as refrigerant shortage.
The power consumption is low comparing with that in the normal operation when refrigerant is
insufficient, and refrigerant shortage is detected by checking power consumption.
Power consumption
Refrigerant shortage zone
50 Hz
Frequency
(R11262)
II: Detecting by discharge pipe temperature
If the discharge pipe temperature is higher than the target discharge pipe temperature, and the
electronic expansion valve is fully open for more than the specified time, it is regarded as
refrigerant shortage.
Target discharge
pipe temperature
Refrigerant shortage
zone
(R1391)
Refer to page 57 for detail.
41
Function and Control
SiBE041010EA
Part 5
Remote Controller
1. Remote Controller .................................................................................43
Remote Controller
42
Remote Controller
SiBE041010EA
1. Remote Controller
Display (LCD)
Signal transmitter
• Displays the current settings.
(In this illustration, each section is
shown with all its displays on for the
purpose of explanation.)
Receiver
TEMPERATURE
adjustment buttons
• To use the remote controller, aim the
transmitter at the indoor unit. If there
is anything to block signals between
the unit and the remote controller,
such as a curtain, the unit will not
operate.
• The maximum distance for
communication is approx. 7 m.
• Changes the temperature setting.
QUIET
ECONO
1
COMFORT
: AUTO
18 ~ 30 ˚C
: DRY
Not available
: COOL
18 ~ 32 ˚C
: HEAT
10 ~ 30 ˚C
: FAN
Not available
SWING
button
ON/OFF button
• ECONO operation
• Press this button once to start
operation.
Press once again to stop it.
POWERFUL2 button
(R18210)
• POWERFUL operation
FTX series
ATX series
Reference
Refer to the following pages for detail.
Note:
43
ARC433A87
ARC433A89
1 ECONO operation
P.26
2 POWERFUL operation
P.27
Refer to the operation manual of applicable model for detail. You can download operation
manuals from ‘DISTRIBUTOR’S PAGE’:
DISTRIBUTOR’S PAGE → Product Information → Operation/Installation Manual
(URL: http://global.daikin.com/Daikin/global/Distributors_admin/user_mng/login.php)
Remote Controller
SiBE041010EA
Remote Controller
Open the Front Cover
R
MODE button
• Selects the operation mode.
AUTO
DRY
COOL
HEAT
FAN
FAN setting button
• Selects the airflow rate setting
every time you press this button.
ON TIMER button
• Press this button and adjust
the day and time with TIMER
setting button.
Press this button again to
complete TIMER setting.
Auto
Indoor unit quiet
Low
Middle low
OFF TIMER button
• Press this button and adjust
the day and time with TIMER
setting button.
Press this button again to
complete TIMER setting.
High
Middle high
Middle
• In indoor unit quiet operation,
operation sound becomes weak.
(The airflow rate also decreases.)
• In DRY operation, the airflow rate
setting is not available.
TIMER Setting button
• Changes the ON/OFF TIMER
settings.
COMFORT4 button
• The airflow direction will be in
upward while in COOL
operation, in downward while
in HEAT operation. This
function will prevent cold or
warm air from directly blowing
on your body.
SWING3 button
CLOCK5 button
RESET button
• Restarts the unit if it freezes.
• Use a thin object to push.
• Adjusts the airflow direction.
• When you press the SWING button,
the flap moves up and down.
The flap stops when you pressed the
SWING button again.
TIMER CANCEL button
• Cancels the timer setting.
(R19105)
Reference
Refer to the following pages for detail.
3 Auto-swing setting
4 COMFORT AIRFLOW
operation
Note:
Remote Controller
P.21
5 Clock setting
P.27
P.21, 22
Refer to the operation manual of applicable model for detail. You can download operation
manuals from ‘DISTRIBUTOR’S PAGE’:
DISTRIBUTOR’S PAGE → Product Information → Operation/Installation Manual
(URL: http://global.daikin.com/Daikin/global/Distributors_admin/user_mng/login.php)
44
SiBE041010EA
Part 6
Service Diagnosis
1. Troubleshooting with LED .....................................................................46
1.1 Indoor Unit..............................................................................................46
1.2 Outdoor Unit ...........................................................................................46
2. Problem Symptoms and Measures .......................................................47
3. Service Check Function ........................................................................48
4. Troubleshooting ....................................................................................51
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
4.13
4.14
4.15
4.16
4.17
4.18
4.19
4.20
4.21
4.22
4.23
4.24
Error Codes and Description ..................................................................51
Indoor Unit PCB Abnormality .................................................................52
Freeze-up Protection Control or Heating Peak-cut Control....................53
Fan Motor (DC Motor) or Related Abnormality.......................................54
Thermistor or Related Abnormality (Indoor Unit)....................................56
Refrigerant Shortage ..............................................................................57
Low-voltage Detection or Over-voltage Detection..................................59
Signal Transmission Error (between Indoor Unit and Outdoor Unit) ......61
Unspecified Voltage (between Indoor Unit and Outdoor Unit) ...............63
Outdoor Unit PCB Abnormality...............................................................64
OL Activation (Compressor Overload) ...................................................65
Compressor Lock ...................................................................................67
DC Fan Lock ..........................................................................................68
Input Overcurrent Detection ...................................................................69
Four Way Valve Abnormality..................................................................70
Discharge Pipe Temperature Control.....................................................72
High Pressure Control in Cooling ...........................................................73
Compressor System Sensor Abnormality ..............................................74
Position Sensor Abnormality ..................................................................75
DC Voltage / Current Sensor Abnormality..............................................77
Thermistor or Related Abnormality (Outdoor Unit).................................78
Electrical Box Temperature Rise............................................................80
Radiation Fin Temperature Rise ............................................................81
Output Overcurrent Detection ................................................................83
5. Check ....................................................................................................85
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
5.12
5.13
45
Thermistor Resistance Check ................................................................85
Fan Motor Connector Output Check ......................................................86
Power Supply Waveforms Check...........................................................87
Electronic Expansion Valve Check.........................................................87
Four Way Valve Performance Check .....................................................88
Inverter Units Refrigerant System Check ...............................................88
Inverter Analyzer Check .........................................................................89
Rotation Pulse Check on the Outdoor Unit PCB ....................................90
Installation Condition Check...................................................................91
Discharge Pressure Check.....................................................................91
Outdoor Fan System Check ...................................................................92
Main Circuit Short Check........................................................................92
Power Module Check .............................................................................93
Service Diagnosis
SiBE041010EA
Troubleshooting with LED
1. Troubleshooting with LED
1.1
Indoor Unit
Operation Lamp
The operation lamp blinks when any of the following errors is detected.
1. When a protection device of the indoor or outdoor unit is activated, or when the thermistor
malfunctions.
2. When a signal transmission error occurs between the indoor and outdoor units.
In either case, conduct the diagnostic procedure described in the following pages.
Operation lamp (green)
(R11948)
Service Monitor
1.2
The indoor unit has one green LED (LED A) on the control PCB. When the microcomputer
works in order, the LED A blinks.
Outdoor Unit
The outdoor unit has one green LED (LED A) on the PCB. When the microcomputer works in
order, the LED A blinks.
Service Diagnosis
46
Problem Symptoms and Measures
SiBE041010EA
2. Problem Symptoms and Measures
Symptom
Check Item
The unit does not operate. Check the power supply.
Check the type of the indoor unit.
Check the outdoor temperature.
Diagnose with remote controller
indication.
Operation sometimes
stops.
Details of Measure
Reference
Page
Check if the rated voltage is supplied.
Check if the indoor unit type is compatible with
the outdoor unit.
—
Heating operation cannot be used when the
outdoor temperature is 18°CWB or higher, and
cooling operation cannot be used when the
outdoor temperature is below 10°CDB.
—
—
51
Check the remote controller
addresses.
Check the power supply.
Check if address settings for the remote
controller and indoor unit are correct.
A power failure of 2 to 10 cycles stops air
conditioner operation. (Operation lamp OFF)
Check the outdoor temperature.
Heating operation cannot be used when the
outdoor temperature is 18°CWB or higher, and
cooling operation cannot be used when the
outdoor temperature is below 10°CDB.
—
—
51
Diagnose with remote controller
indication.
The unit operates but does Check for wiring and piping errors in
not cool, or does not heat. the connection between the indoor
—
unit and outdoor unit.
Check for thermistor detection errors. Check if the thermistor is mounted securely.
97
—
—
—
Check for faulty operation of the
electronic expansion valve.
Set the unit to cooling operation, and check the
liquid pipe temperature to see if the electronic
expansion valve works.
—
Diagnose with remote controller
indication.
—
51
Diagnose by service port pressure
and operating current.
Large operating noise and Check the output voltage of the
vibrations
power module.
Check the power module.
Check the installation condition.
47
—
Check for refrigerant shortage.
57
—
93
—
Check if the required spaces for installation
(specified in the installation manual) are
provided.
—
—
Service Diagnosis
SiBE041010EA
Service Check Function
3. Service Check Function
Check Method 1
1. When the timer cancel button is held down for 5 seconds, 00 is displayed on the temperature
display screen.
Timer cancel button
<ARC433 Series>
(R18206)
2. Press the timer cancel button repeatedly until a long beep sounds.
„ The code indication changes in the sequence shown below.
No.
Code
No.
Code
No.
Code
1
2
00
U4
13
14
C7
A3
25
26
UA
UH
3
4
L5
E6
15
16
H8
H9
27
28
P4
L3
5
6
H6
H0
17
18
C9
C4
29
30
L4
H7
7
8
A6
E7
19
20
C5
J3
31
32
U2
EA
9
10
U0
F3
21
22
J6
E5
33
34
AH
FA
11
12
A5
F6
23
24
A1
E1
for FTX models only
Note:
Service Diagnosis
1. A short beep or two consecutive beeps indicate non-corresponding codes.
2. To return to the normal mode, hold the timer cancel button down for 5 seconds. When the
remote controller is left untouched for 60 seconds, it also returns to the normal mode.
3. Not all the error codes are displayed. When you cannot find the error code, try the check
method 2. (→ Refer to page 49.)
48
Service Check Function
SiBE041010EA
Check Method 2
1. Press the center of the [TEMP] button and the [MODE] button at the same time to enter the
diagnosis mode.
(R19114)
The left-side number blinks.
(R14967)
2. Press the [TEMP] or
beeps or the long beep.
button and change the number until you hear the two consecutive
(R19115)
3. Diagnose by the sound.
beep : The left-side number does not correspond with the error code.
two consecutive beeps : The left-side number corresponds with the error code but the
right-side number does not.
long beep : Both the left-side and right-side numbers correspond with the error code.
The numbers indicated when you hear the long beep are the error code.
Error codes and description → Refer to page 51.
4. Press the [MODE] button.
(R19116)
The right-side number blinks.
(R14968)
49
Service Diagnosis
SiBE041010EA
Service Check Function
5. Press the [TEMP]
or
button and change the number until you hear the long beep.
(R19115)
6. Diagnose by the sound.
beep : The left-side number does not correspond with the error code.
two consecutive beeps : The left-side number corresponds with the error code but
the right-side number does not.
long beep : Both the left-side and right-side numbers correspond with the error code.
7. Determine the error code.
The numbers indicated when you hear the long beep are the error code.
Error codes and description → Refer to page 51.
8. Press the [MODE] button to exit from the diagnosis mode.
(R19116)
The display
means the trial operation mode.
Refer to page 96 for trial operation.
(R14969)
9. Press the [ON/OFF] button twice to return to the normal mode.
(R19117)
Note:
Service Diagnosis
When the remote controller is left untouched for 60 seconds, it returns to the normal mode.
50
Troubleshooting
SiBE041010EA
4. Troubleshooting
4.1
Error Codes and Description
Error Codes
System
Indoor
Unit
Outdoor
Unit
00
U0
U2
U4
UA
A1
A5
A6
C4
C9
E1
E5
E6
E7
E8
EA
F3
F6
H0
H6
H8
H9
J3
J6
L3
L4
L5
P4
Reference
Page
Description
Normal
—
Refrigerant shortage
57
Low-voltage detection or over-voltage detection
59
Signal transmission error (between indoor unit and outdoor unit)
61
Unspecified voltage (between indoor unit and outdoor unit)
63
Indoor unit PCB abnormality
52
Freeze-up protection control or heating peak-cut control
53
Fan motor (DC motor) or related abnormality
54
Indoor heat exchanger thermistor or related abnormality
56
Room temperature thermistor or related abnormality
56
Outdoor unit PCB abnormality
64
OL activation (compressor overload)
65
Compressor lock
67
DC fan lock
68
Input overcurrent detection
69
Four way valve abnormality
70
Discharge pipe temperature control
72
High pressure control in cooling
73
Compressor system sensor abnormality
74
Position sensor abnormality
75
DC voltage / current sensor abnormality
77
Outdoor temperature thermistor or related abnormality
78
Discharge pipe thermistor or related abnormality
78
Outdoor heat exchanger thermistor or related abnormality
78
Electrical box temperature rise
80
Radiation fin temperature rise
81
Output overcurrent detection
83
Radiation fin thermistor or related abnormality
78
: Displayed only when system-down occurs.
51
Service Diagnosis
SiBE041010EA
4.2
Troubleshooting
Indoor Unit PCB Abnormality
A1
Error Code
Method of Error
Detection
The system checks if the circuit works properly within the microcomputer of the indoor unit.
Error Decision
Conditions
The system cannot set the internal settings.
Supposed
Causes
„
„
„
„
Wrong models interconnected
Defective indoor unit PCB
Disconnection of connector
Reduction of power supply voltage
Troubleshooting
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Caution
Check the combination of the
indoor and outdoor unit.
OK?
NO
Match the compatible
models.
YES
Check the connection of
connectors (See Note).
OK?
∗ To secure the connection,
once disconnect the connector
and then reconnect it.
YES
Check the power supply
voltage.
NO
Voltage as rated?
NO
Correct the power
supply.
YES
Start operation.
Correct the connection.
Error repeats?
YES
NO
Error repeats?
YES
Replace the indoor unit
PCB.
Completed.
Check the power supply
voltage.
NO
Voltage as rated?
NO
Correct the power
supply.
YES
Start operation.
Error repeats?
YES
NO
Replace the indoor unit
PCB.
Completed.
Completed.
(R15310)
Note:
Check the following connector.
Model Type
Wall Mounted Type
Service Diagnosis
Connector
Terminal board ~ Control PCB (H1, H2, H3)
52
Troubleshooting
4.3
SiBE041010EA
Freeze-up Protection Control or Heating Peak-cut
Control
Error Code
A5
Method of Error
Detection
„ Freeze-up protection control
Error Decision
Conditions
„ Freeze-up protection control
During cooling operation, the freeze-up protection control (operation halt) is activated
according to the temperature detected by the indoor heat exchanger thermistor.
„ Heating peak-cut control
During heating operation, the temperature detected by the indoor heat exchanger thermistor
is used for the heating peak-cut control (operation halt, outdoor fan stop, etc.)
During cooling operation, the indoor heat exchanger temperature is below 0°C.
„ Heating peak-cut control
During heating operation, the indoor heat exchanger temperature is above 65°C
Supposed
Causes
„
„
„
„
„
Short-circuited air
Clogged air filter of the indoor unit
Dust accumulation on the indoor heat exchanger
Defective indoor heat exchanger thermistor
Defective indoor unit PCB
Troubleshooting
Caution
Check No.01
Refer to P.85
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Check the air passage.
YES
Is there any short circuit?
Provide sufficient air passage.
NO
Check the air filter.
Dirty?
YES
Clean the air filter.
NO
Check the dust accumulation on
the indoor heat exchanger.
Dirty?
YES
Clean the indoor heat
exchanger.
NO
Check No. 01
Check the indoor heat exchanger
thermistor.
As
described in the
thermistor characteristic
chart?
YES
NO
Replace the thermistor.
Replace the indoor unit PCB.
(R15715)
53
Service Diagnosis
SiBE041010EA
4.4
Troubleshooting
Fan Motor (DC Motor) or Related Abnormality
Error Code
A6
Method of Error
Detection
The rotation speed detected by the Hall IC during fan motor operation is used to determine
abnormal fan motor operation.
Error Decision
Conditions
The detected rotation speed does not reach the demanded rotation speed of the target tap, and
is less than 50% of the maximum fan motor rotation speed.
Supposed
Causes
„
„
„
„
„
„
„
Service Diagnosis
Disconnection of connector
Foreign matters stuck in the fan
Layer short inside the fan motor winding
Breaking of wire inside the fan motor
Breaking of the fan motor lead wires
Defective capacitor of the fan motor
Defective indoor unit PCB
54
Troubleshooting
SiBE041010EA
Troubleshooting
Caution
Check No.03
Refer to P.86
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Turn off the power supply.
(Unplug the power cable or turn
the breaker off.)
Note: The motor may break when the
motor connector is disconnected
with the power supply on.
(Turn off the power supply before
connecting the connector also.)
Check the connector for
connection.
∗ To secure the connection,
once disconnect the connector
and then reconnect it.
OK?
NO
Correct the connection.
YES
Foreign matters in or
around the fan?
YES
Remove the foreign matters.
NO
Rotate the fan by hand.
Fan rotates smoothly?
NO
YES
Check No. 03
Check the fan motor for
breakdown or short circuit.
Abnormal
sound occurs?
NO
YES
Rubber
cushion
Bearing
rubber
cushion
Is the rubber cushion
properly fitted?
YES
Replace the bearing rubber
cushion.
NO
Resistance OK?
NO
Correct the position of
rubber cushion or replace
the rubber cushion.
Replace the indoor fan motor.
YES
Turn the power on again.
Check No. 03
Check the motor control voltage.
Is the motor control
voltage 15 VDC
generated?
NO
Replace the indoor unit PCB (1).
YES
Check No. 03
Check the indoor unit PCB for
rotation pulse.
Is the rotation pulse
generated?
YES
NO
Replace the indoor fan motor.
Replace the indoor unit PCB (1).
(R18153)
55
Service Diagnosis
SiBE041010EA
4.5
Troubleshooting
Thermistor or Related Abnormality (Indoor Unit)
Error Code
C4, C9
Method of Error
Detection
The temperatures detected by the thermistors determine thermistor errors.
Error Decision
Conditions
The thermistor input is more than 4.96 V or less than 0.04 V during compressor operation.
Supposed
Causes
„ Disconnection of connector
„ Thermistor corresponding to the error code is defective
„ Defective indoor unit PCB
Troubleshooting
Caution
Check No.01
Refer to P.85
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Check the connection of
connectors.
Normal?
NO
Correct the connection.
YES
Check No. 01
Check the thermistor resistance
value.
Normal?
NO
YES
Replace the thermistor.
Replace the indoor unit PCB.
(R15717)
C4 : Indoor heat exchanger thermistor
C9 : Room temperature thermistor
Service Diagnosis
56
Troubleshooting
4.6
SiBE041010EA
Refrigerant Shortage
Error Code
Method of Error
Detection
U0
Refrigerant shortage detection I:
Refrigerant shortage is detected by checking the input current value and the compressor
running frequency. If the refrigerant is short, the input current is lower than the normal value.
Refrigerant shortage detection II:
Refrigerant shortage is detected by checking the discharge pipe temperature and the opening of
the electronic expansion valve. If the refrigerant is short, the discharge pipe temperature tends
to rise.
Error Decision
Conditions
Refrigerant shortage detection I:
The following conditions continue for 7 minutes.
Š Input current × input voltage ≤ A × output frequency + B
Š Output frequency > C
20/25 class
35 class
A (–)
B (W)
C (Hz)
828/256
777/256
–10
–15
50
50
Refrigerant shortage detection II:
The following conditions continue for 80 seconds.
Š Opening of the electronic expansion valve ≥ D
Š Discharge pipe temperature > E × target discharge pipe temperature + F
D (pulse)
20/25 class
35 class
Cooling
Heating
Cooling
Heating
470
470
E (–)
F (°C)
190/128
–7
211/128
160/128
–11
–1.5
172/128
–8
„ If the error repeats, the system is shut down.
„ Reset condition: Continuous run for about 60 minutes without any other error
Supposed
Causes
„ Disconnection of the discharge pipe thermistor, indoor or outdoor heat exchanger thermistor,
„
„
„
„
57
room or outdoor temperature thermistor
Closed stop valve
Refrigerant shortage (refrigerant leakage)
Poor compression performance of compressor
Defective electronic expansion valve
Service Diagnosis
SiBE041010EA
Troubleshooting
Troubleshooting
Caution
Check No.01
Refer to P.85
Check No.12
Refer to P.87
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Any thermistor
disconnected?
NO
Stop valve closed?
YES
∗ Discharge pipe thermistor
∗ Indoor or outdoor heat exchanger thermistor
∗ Room temperature thermistor
∗ Outdoor temperature thermistor
YES
Replace the thermistor(s) in
position.
Open the stop valve.
NO
Check for refrigerant shortage.
Oil oozing at relay
pipe connections?
YES
Repair the pipe flare or
replace the union.
NO
Oil oozing at internal
piping?
YES
NO
Compressor vibrating
too much?
NO
Check No. 12
Electronic expansion valve
functioning?
YES Check the power transistor
harness for loosening.
Correct it as required. Also
replace the cracked pipe.
Check the pipes for
improper contact and
correct them as required.
Replace the cracked pipe.
NO
Replace the electronic
expansion valve.
YES
Change for a specified amount of
fresh refrigerant.
Refrigerant shortage error
again?
NO
YES
Check No. 01
Check the thermistors.
NG
Replace the defective
thermistor(s).
OK
Replace the outdoor unit PCB.
Error again?
YES
Replace the compressor.
NO
Completed.
Completed.
(R18930)
Service Diagnosis
58
Troubleshooting
4.7
SiBE041010EA
Low-voltage Detection or Over-voltage Detection
Error Code
U2
Method of Error
Detection
Low-voltage detection:
An abnormal voltage drop is detected by the DC voltage detection circuit.
Over-voltage detection:
An abnormal voltage rise is detected by the over-voltage detection circuit.
Error Decision
Conditions
Low-voltage detection:
„ The voltage detected by the DC voltage detection circuit is below 180 V.
„ The compressor stops if the error occurs, and restarts automatically after 3-minute standby.
Over-voltage detection:
„ An over-voltage signal is fed from the over-voltage detection circuit to the microcomputer.
„ The compressor stops if the error occurs, and restarts automatically after 3-minute standby.
Supposed
Causes
59
„
„
„
„
„
„
„
„
„
„
Power supply voltage is not as specified.
Defective DC voltage detection circuit
Defective over-voltage detection circuit
Defective PAM control part
Disconnection of compressor harness
Short circuit inside the fan motor winding
Noise
Momentary fall of voltage
Momentary power failure
Defective outdoor unit PCB
Service Diagnosis
SiBE041010EA
Troubleshooting
Troubleshooting
Caution
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Check the power supply voltage.
Is the
voltage fluctuation
within ±10% from the
rated value?
NO
Correct the power supply.
YES
Check the connection of the
compressor harness.
Loose or
disconnected?
YES
Reconnect the harness.
NO
Rotate
the outdoor fan by
hand. Does the outdoor fan
rotate smoothly?
NO
Replace both the fan motor
and the outdoor unit PCB.
YES
(Precaution before turning on the power again)
Make sure the power has been off for at
least 30 seconds.
Turn on the
power again. System
restarted?
YES Disturbance factors
∗ Noise ∗ Power supply distortion
Check for such factors for a
long term.
∗ Try to restart a few times.
NO
Repeat a few
times.
Replace the outdoor
unit PCB.
(R19100)
Service Diagnosis
60
Troubleshooting
4.8
SiBE041010EA
Signal Transmission Error (between Indoor Unit and
Outdoor Unit)
Error Code
U4
Method of Error
Detection
The data received from the outdoor unit in signal transmission is checked whether it is normal.
Error Decision
Conditions
The data sent from the outdoor unit cannot be received normally, or the content of the data is
abnormal.
Supposed
Causes
„
„
„
„
„
„
„
61
Reduction of power supply voltage
Wiring error
Breaking of the connection wires between the indoor and outdoor units (wire No. 3)
Defective outdoor unit PCB
Short circuit inside the fan motor winding
Defective indoor unit PCB
Disturbed power supply waveform
Service Diagnosis
SiBE041010EA
Troubleshooting
Troubleshooting
Caution
Check No.11
Refer to P.87
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Check the power supply voltage.
Is the
voltage fluctuation
within ±10% from the
rated value?
NO
Correct the power supply.
YES
Check the indoor unit - outdoor
unit connection wires.
Is there any wiring error?
YES
Correct the indoor unit outdoor unit connection wires.
NO
Check the voltage of the
connection wires on the indoor
terminal board between No. 1
and No. 3, and between No. 2
and No. 3.
Properly insulated?
NO
Check the LED A on the outdoor
unit PCB.
Is LED A blinking?
YES
∗ Before you check the LED A, cancel
the standby electricity saving
function by starting fan operation
with the remote controller.
∗ Wait at least for 7 sec. after turning
on the power.
NO
Replace the connection wires
between the indoor unit and
outdoor unit.
Diagnose the outdoor unit
PCB.
YES
Rotate the
outdoor fan by hand.
Does the outdoor fan rotate
smoothly?
NO
Replace both the fan motor
and the outdoor unit PCB.
YES
Check No.11
Check the power supply
waveform.
Is there any disturbance?
YES
NO
Replace the indoor unit PCB.
Locate the cause of the
disturbance of the power
supply waveform, and correct
it.
(R18180)
Service Diagnosis
62
Troubleshooting
4.9
SiBE041010EA
Unspecified Voltage (between Indoor Unit and Outdoor
Unit)
Error Code
UA
Method of Error
Detection
The supply power is detected for its requirements (different from pair type and multi type) by the
indoor / outdoor transmission signal.
Error Decision
Conditions
The pair type and multi type are interconnected.
Supposed
Causes
„
„
„
„
„
Wrong models interconnected
Wrong wiring of connecting wires
Wrong indoor unit PCB or outdoor unit PCB mounted
Defective indoor unit PCB
Defective outdoor unit PCB
Troubleshooting
Caution
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Check the combination of the
indoor and outdoor unit.
OK?
NO
Match the compatible models.
YES
Are the
connection wires connected
property?
NO
Correct the connection.
YES
Check the code numbers
(2P01234, for example) of the
indoor and outdoor unit PCB with
the Parts List.
Matched compatibly?
YES
NO
Change for the correct PCB.
Replace the indoor unit PCB
(or the outdoor unit PCB).
(R11707)
63
Service Diagnosis
SiBE041010EA
Troubleshooting
4.10 Outdoor Unit PCB Abnormality
Error Code
E1
Method of Error
Detection
„ The system checks if the microprocessor is working in order.
„ The system checks if the zero-cross signal comes in properly.
Error Decision
Conditions
„ The microprocessor program runs out of control.
„ The zero-cross signal is not detected.
Supposed
Causes
„
„
„
„
„
Defective outdoor unit PCB
Broken harness between PCBs
Noise
Momentary fall of voltage
Momentary power failure
Troubleshooting
Caution
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
∗ Before you check the LED A,
cancel the standby electricity
saving function by starting fan
operation with the remote
controller.
∗ Wait at least for 7 sec. after
turning on the power.
Turn on the power again.
NO
Is LED A blinking?
Replace the outdoor unit
PCB (2).
YES
Check if the outdoor unit is
grounded.
Grounded?
NO
Ground the system.
YES
Is the harness
broken?
YES
Replace the harness.
NO
Zero-cross signal
abnormality.
Replace the outdoor unit
PCB (1).
(R19101)
Service Diagnosis
64
Troubleshooting
SiBE041010EA
4.11 OL Activation (Compressor Overload)
Error Code
E5
Method of Error
Detection
A compressor overload is detected through overload protector (OL).
Error Decision
Conditions
„ If the error repeats, the system is shut down.
„ Reset condition: Continuous run for about 60 minutes without any other error
Supposed
Causes
„
„
„
„
„
„
„
„
„
„
„
„
65
Disconnection of discharge pipe thermistor
Defective discharge pipe thermistor
Disconnection of connector [S40]
Disconnection of 2 terminals of OL (Q1L)
Defective OL (Q1L)
Broken OL harness
Defective electronic expansion valve or coil
Defective four way valve or coil
Defective outdoor unit PCB
Refrigerant shortage
Water mixed in refrigerant
Defective stop valve
Service Diagnosis
SiBE041010EA
Troubleshooting
Troubleshooting
Caution
Check No.01
Refer to P.85
Check No.12
Refer to P.87
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Discharge
pipe thermistor
disconnected?
NG
∗ Discharge pipe thermistor
Replace the discharge pipe
thermistor.
OK
Connectors are properly
connected?
Check No.14
Refer to P.88
Insert the thermistor in
position.
NO
Check No. 01
Check the thermistors.
Check No.13
Refer to P.88
YES
NO
∗ Connector [S40]
∗ 2 terminals of OL (Q1L)
Connect the connectors
properly.
YES
Disconnect the connector [S40]
from the PCB.
Check
Resistance
the resistance
∞
Disconnect the 2 terminals of
between the 2 terminals on
the OL (Q1L).
the connector
[S40].
Resistance
Check the
∞
resistance between the
Replace the OL (Q1L).
2 terminals of the OL
(Q1L).
Nearly 0 Ω
Nearly 0 Ω
Check No. 12
Check the electronic
expansion valve.
NG
Replace the OL harness.
Replace the electronic
expansion valve or the coil.
OK
Check No. 13
Check the four way
valve.
NG
Replace the four way valve
or the coil.
Replace the outdoor unit
PCB.
OK
Check No. 14
Check the refrigerant
line.
OK
NG
∗ Refrigerant shortage
∗ Water mixed
∗ Stop valve
Refer to the refrigerant line
check procedure.
Replace the outdoor unit
PCB.
(R18316)
Note:
Service Diagnosis
OL (Q1L) activating temperature: 120°C
OL (Q1L) recovery temperature: 95°C
66
Troubleshooting
SiBE041010EA
4.12 Compressor Lock
Error Code
E6
Method of Error
Detection
A compressor lock is detected by checking the compressor running condition through the
position detection circuit.
Error Decision
Conditions
„ Operation stops due to overcurrent.
„ If the error repeats, the system is shut down.
„ Reset condition: Continuous run for about 11 minutes without any other error
Supposed
Causes
„ Compressor locked
„ Compressor harness disconnected
Troubleshooting
Caution
Check No.15
Refer to P.89
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
(Precaution before turning on the power again)
Make sure the power has been off for at least 30 seconds.
Turn off the power. Disconnect the
harnesses U, V, and W.
Check No.15
Check with the inverter analyzer.
Normal?
∗ Inverter analyzer:
RSUK0917C
NO
Correct the power supply or
replace the outdoor unit
PCB.
YES
Turn off the power and reconnect
the harnesses. Turn on the power
again and restart the system.
Emergency
stop without compressor
running?
YES
Replace the compressor.
NO
System shut
down after errors repeated
several times?
YES
NO
Check the outdoor electronic
expansion valve coil.
Replace it as required.
Replace the compressor.
(R18317)
67
Service Diagnosis
SiBE041010EA
Troubleshooting
4.13 DC Fan Lock
Error Code
E7
Method of Error
Detection
An error is determined with the high-voltage fan motor rotation speed detected by the Hall IC.
Error Decision
Conditions
„ The fan does not start in about 15 ~ 60 seconds even when the fan motor is running.
„ If the error repeats, the system is shut down.
„ Reset condition: Continuous run for about 11 minutes without any other error
Supposed
Causes
„
„
„
„
Disconnection of the fan motor
Foreign matter stuck in the fan
Defective fan motor
Defective outdoor unit PCB
Troubleshooting
Caution
Check No.16
Refer to P.90
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Fan motor connector
disconnected?
YES
Turn off the power and
reconnect the connector.
NO
Foreign matters in or
around the fan?
YES
Remove the foreign
matters.
NO
Turn on the power.
Rotate the fan.
Fan rotates
smoothly?
NO
Replace the outdoor fan
motor.
YES
Check No. 16
Check the rotation pulse input on
the outdoor unit PCB.
Pulse signal generated?
YES
NO
Replace the outdoor fan
motor.
Replace the outdoor unit
PCB.
(R15675)
Service Diagnosis
68
Troubleshooting
SiBE041010EA
4.14 Input Overcurrent Detection
Error Code
E8
Method of Error
Detection
An input overcurrent is detected by checking the input current value with the compressor
running.
Error Decision
Conditions
The current exceeds about 14 A for 2.5 seconds with the compressor running.
(The upper limit of the current decreases when the outdoor temperature exceeds a certain
level.)
Supposed
Causes
„
„
„
„
„
„
„
Power supply voltage is not as specified.
Outdoor temperature is out of operation range.
Short circuit
Power supply voltage is not as specified.
Defective outdoor unit PCB
Defective compressor
Defective power module
Troubleshooting
Caution
Check No.15
Refer to P.89
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
∗ An input overcurrent may result from wrong internal wiring. If the system is interrupted by an input
overcurrent after the wires have been disconnected and reconnected for part replacement, check the
wiring again.
Check No. 17
Check the installation condition.
Check No.17
Refer to P.91
Check No.18
Refer to P.91
Is the
power supply
voltage fluctuation within
±10% from the rated
value?
NO
Correct the power supply.
YES
Start operation and measure the
input current.
Input current flowing
above its stop level?
NO
Replace the outdoor unit
PCB.
YES
Turn off the power and disconnect
the harnesses U, V, and W.
Check No.15
Check with the inverter analyzer.
Any LED off?
NO
∗ Inverter analyzer:
RSUK0917C
YES
Correct the power supply or
replace the outdoor unit
PCB.
Turn off the power, and reconnect
the harnesses. Turn on the power
again and start operation.
Check No. 18
Check the discharge pressure.
(R18798)
69
Service Diagnosis
SiBE041010EA
Troubleshooting
4.15 Four Way Valve Abnormality
Error Code
EA
Method of Error
Detection
The room temperature thermistor and the indoor heat exchanger thermistor are checked if they
function within their normal ranges in each operation mode.
Error Decision
Conditions
„ Cooling / Dry
A following condition continues over 10 minutes after operating for 5 minutes.
A – B < –5°C
„ Heating
B – A < –5°C
A: Room thermistor temperature
B: Indoor heat exchanger temperature
„ If the error repeats, the system is shut down.
„ Reset condition: Continuous run for about 60 minutes without any other error
Supposed
Causes
Service Diagnosis
„
„
„
„
„
„
„
Disconnection of four way valve coil
Defective four way valve, coil, or harness
Defective outdoor unit PCB
Defective thermistor
Refrigerant shortage
Water mixed in refrigerant
Defective stop valve
70
Troubleshooting
SiBE041010EA
Troubleshooting
Caution
Check No.01
Refer to P.85
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Four way valve coil
disconnected (loose)?
YES
Correct the four way valve
coil.
NO
Check No.13
Refer to P.88
Harness out of connector?
YES
Reconnect the harness.
NO
Check No.14
Refer to P.88
Check the continuity of the four way
valve coil and harness.
Disconnect the harness from the
connector.
Resistance
between harnesses about
1000 ~ 2000 Ω?
NO
Replace the four way
valve coil.
YES
Check No. 13
Check the four way valve
switching output.
NG
Replace the outdoor
unit PCB.
OK
Any thermistor
disconnected?
YES
Reconnect the
thermistor(s).
NO
Check No. 01
Check the thermistors.
NG
Replace the defective
thermistor(s).
OK
Check No. 14
Check the refrigerant
line.
NG
∗ Refrigerant shortage
∗ Water mixed
∗ Stop valve
Refer to the refrigerant line
check procedure.
OK
Replace the four way valve
(defective or dust-clogged).
(R15824)
71
Service Diagnosis
SiBE041010EA
Troubleshooting
4.16 Discharge Pipe Temperature Control
Error Code
F3
Method of Error
Detection
An error is determined with the temperature detected by the discharge pipe thermistor.
Error Decision
Conditions
„ If the temperature detected by the discharge pipe thermistor rises above A°C, the
compressor stops.
„ The error is cleared when the discharge pipe temperature has dropped below B°C.
A (°C)
B (°C)
(1) above 45 Hz (rising), above 40 Hz (dropping)
110
97
(2) 30 ~ 45 Hz (rising), 25 ~ 40 Hz (dropping)
(3) below 30 Hz (rising), below 25 Hz (dropping)
105
99
92
86
„ If the error repeats, the system is shut down.
„ Reset condition: Continuous run for about 60 minutes without any other error
Supposed
Causes
„ Defective discharge pipe thermistor
„
„
„
„
„
„
(Defective outdoor heat exchanger thermistor or outdoor temperature thermistor)
Defective electronic expansion valve or coil
Refrigerant shortage
Defective four way valve
Water mixed in refrigerant
Defective stop valve
Defective outdoor unit PCB
Troubleshooting
Caution
Check No.01
Refer to P.85
Check No.12
Refer to P.87
Check No.14
Refer to P.88
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Check No. 01
Check the thermistors.
OK
Check No. 12
Check the electronic
expansion valve.
NG
∗ Discharge pipe thermistor
∗ Outdoor heat exchanger thermistor
∗ Outdoor temperature thermistor
NG
Replace the defective
thermistor(s).
Replace the electronic
expansion valve or the coil.
OK
Check No. 14
Check the refrigerant
line.
OK
NG
∗ Refrigerant shortage
∗ Four way valve
∗ Water mixed
∗ Stop valve
Refer to the refrigerant line
check procedure.
Replace the outdoor unit
PCB.
(R15825)
Service Diagnosis
72
Troubleshooting
SiBE041010EA
4.17 High Pressure Control in Cooling
Error Code
F6
Method of Error
Detection
High-pressure control (operation halt, frequency drop, etc.) is activated in cooling operation if
the temperature sensed by the outdoor heat exchanger thermistor exceeds the limit.
Error Decision
Conditions
„ The temperature sensed by the outdoor heat exchanger thermistor rises above about
60°C.
„ The error is cleared when the temperature drops below about 50°C.
Supposed
Causes
„
„
„
„
„
„
„
The installation space is not large enough.
Dirty outdoor heat exchanger
Defective outdoor fan motor
Defective stop valve
Defective electronic expansion valve or coil
Defective outdoor heat exchanger thermistor
Defective outdoor unit PCB
Troubleshooting
Caution
Check No.01
Refer to P.85
Check No.12
Refer to P.87
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Check the installation space.
Check No. 17
Check the installation
condition.
NG
OK
Check No.17
Refer to P.91
Check No. 19
Check the outdoor fan.
NG
OK
Check No.18
Refer to P.91
Check No. 18
Check the discharge
pressure.
NG
Change the installation
location or direction.
Clean the outdoor heat
exchanger.
Replace the outdoor fan
motor.
Reconnect the connector or
fan motor lead wires.
Replace the stop valve.
OK
Check No.19
Refer to P.92
Check No. 12
Check the electronic
expansion valve.
NG
OK
Check No. 01
Check the outdoor heat
exchanger thermistor.
NG
Replace the electronic
expansion valve or the coil.
Replace the outdoor unit
PCB.
Replace the outdoor heat
exchanger thermistor.
OK
Replace the outdoor unit
PCB.
(R15667)
73
Service Diagnosis
SiBE041010EA
Troubleshooting
4.18 Compressor System Sensor Abnormality
Error Code
H0
Method of Error
Detection
„ The system checks the DC current before the compressor starts.
Error Decision
Conditions
„ The DC current before compressor start-up is out of the range 0.5 ~ 4.5 V (sensor output
converted to voltage value)
„ The DC voltage before compressor start-up is below 50 V.
Supposed
Causes
„ Broken or disconnected harness
„ Defective outdoor unit PCB
Troubleshooting
Caution
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Check the relay harness for the
compressor.
Is the harness broken?
YES
Replace the harness.
NO
Turn off the power and turn it on
again.
Restart operation
and error displayed
again?
YES
NO
No problem.
Keep on running.
Replace the outdoor unit
PCB.
(R11712)
Service Diagnosis
74
Troubleshooting
SiBE041010EA
4.19 Position Sensor Abnormality
Error Code
H6
Method of Error
Detection
A compressor start-up failure is detected by checking the compressor running condition through
the position detection circuit.
Error Decision
Conditions
„ If the error repeats, the system is shut down.
„ Reset condition: Continuous run for about 11 minutes without any other error
Supposed
Causes
„
„
„
„
„
„
75
Power supply voltage is not as specified.
Start-up failure caused by the closed stop valve
Defective outdoor unit PCB
Disconnection of the compressor relay cable
Input voltage is outside the specified range.
Defective compressor
Service Diagnosis
SiBE041010EA
Troubleshooting
Troubleshooting
Check No.15
Refer to P.89
Check No.18
Refer to P.91
Check No.20
Refer to P.92
Caution
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Turn off the power.
Check the power supply voltage.
Voltage as rated?
NO
Correct the power supply.
YES
Check No. 18
Check the discharge pressure.
OK?
NO
Replace the stop valve.
YES
Check No. 20
Check the short circuit of the diode
bridge.
Normal?
NO
Replace the outdoor unit
PCB.
YES
Check the connection.
Electrical
components or
compressor harnesses
connected as
specified?
NO
Reconnect the electrical
components or compressor
harnesses as specified.
YES
Turn on the power.
Check the electrolytic capacitor
voltage.
320 ± 50 VDC?
NO
Replace the outdoor unit
PCB.
YES
Turn off the power. Disconnect the
harnesses U, V, and W.
Check No.15
Check with the inverter analyzer.
Any LED OFF?
NO
∗ Inverter analyzer:
RSUK0917C
YES
Correct the power supply
or replace the outdoor unit
PCB.
Replace the compressor.
(R18319)
Service Diagnosis
76
Troubleshooting
SiBE041010EA
4.20 DC Voltage / Current Sensor Abnormality
Error Code
H8
Method of Error
Detection
DC voltage or DC current sensor abnormality is identified based on the compressor running
frequency and the input current.
Error Decision
Conditions
„ The compressor running frequency is above 52 Hz.
(The input current is also below 0.1 A.)
„ If the error repeats, the system is shut down.
„ Reset condition: Continuous run for about 60 minutes without any other error
Supposed
Causes
„ Defective outdoor unit PCB
Troubleshooting
Caution
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Replace the outdoor unit PCB.
77
Service Diagnosis
SiBE041010EA
Troubleshooting
4.21 Thermistor or Related Abnormality (Outdoor Unit)
Error Code
H9, J3, J6, P4
Method of Error
Detection
This fault is identified based on the thermistor input voltage to the microcomputer.
A thermistor fault is identified based on the temperature sensed by each thermistor.
Error Decision
Conditions
„ The thermistor input voltage is above 4.96 V or below 0.04 V with the power on.
„ J3 error is judged if the discharge pipe temperature is lower than the heat exchanger
temperature.
Supposed
Causes
„ Disconnection of the connector for the thermistor
„ Thermistor corresponding to the error code is defective
„ Defective heat exchanger thermistor in the case of J3 error (outdoor heat exchanger
thermistor in cooling operation, or indoor heat exchanger thermistor in heating operation)
„ Defective outdoor unit PCB
Troubleshooting
In case of “P4”
Caution
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Replace the outdoor unit PCB.
P4 : Radiation fin thermistor
Service Diagnosis
78
Troubleshooting
Troubleshooting
SiBE041010EA
In case of “H9” “J3” “J6”
Caution
Check No.01
Refer to P.85
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Turn on the power again.
Error displayed
again on remote
controller?
NO
Reconnect the connectors
or thermistors.
YES
Check No. 01
Check the thermistor resistance
value.
Normal?
J3 error: the discharge
pipe temperature is
lower than the heat
exchanger temperature.
Cooling: Outdoor heat
exchanger
temperature
Heating: Indoor heat
exchanger
temperature
NO
Replace the defective
thermistor(s) of the following
thermistors.
∗ Outdoor temperature
thermistor
∗ Discharge pipe thermistor
∗ Outdoor heat exchanger
thermistor
YES
Check No. 01
Check the indoor heat exchanger
thermistor resistance value in the
heating operation.
Indoor heat
exchanger thermistor
functioning?
NO
Replace the indoor heat
exchanger thermistor.
YES
Replace the outdoor unit
PCB.
(R16059)
H9 : Outdoor temperature thermistor
J3 : Discharge pipe thermistor
J6 : Outdoor heat exchanger thermistor
79
Service Diagnosis
SiBE041010EA
Troubleshooting
4.22 Electrical Box Temperature Rise
Error Code
L3
Method of Error
Detection
An electrical box temperature rise is detected by checking the radiation fin thermistor with the
compressor off.
Error Decision
Conditions
„ With the compressor off, the radiation fin temperature is above A°C.
„ The error is cleared when the radiation fin temperature drops below B°C.
„ To cool the electrical components, the outdoor fan starts when the radiation fin temperature
rises above C°C and stops when it drops below B°C.
Supposed
Causes
„
„
„
„
„
A (°C)
B (°C)
C (°C)
93
70
78
Defective outdoor fan motor
Short circuit
Defective radiation fin thermistor
Disconnection of connector
Defective outdoor unit PCB
Troubleshooting
Caution
Check No.17
Refer to P.91
Check No.19
Refer to P.92
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
WARNING
To cool the electrical components,
the outdoor fan starts when the
radiation fin temperature rises
above C ˚C and stops when it
drops below B ˚C.
Turn off the power and turn it on
again.
Error again or outdoor
fan activated?
YES
NO
Check the radiation fin
temperature.
NO
Above A ˚C?
Replace the outdoor unit
PCB.
YES
Check No. 19
Check the outdoor fan or
related system.
NG
Replace the outdoor fan
motor.
Correct the connectors
and fan motor lead wire.
Replace the outdoor unit
PCB.
OK
Radiation fin dirty?
Too dirty
Clean up the radiation fin.
Slightly dirty
Check No. 17
Check the installation condition.
(R19118)
Service Diagnosis
80
Troubleshooting
SiBE041010EA
4.23 Radiation Fin Temperature Rise
Error Code
L4
Method of Error
Detection
A radiation fin temperature rise is detected by checking the radiation fin thermistor with the
compressor on.
Error Decision
Conditions
„
„
„
„
Supposed
Causes
81
„
„
„
„
„
„
If the radiation fin temperature with the compressor on is above A°C.
The error is cleared when the radiation fin temperature drops below B°C.
If the error repeats, the system is shut down.
Reset condition: Continuous run for about 60 minutes without any other error
A (°C)
B (°C)
93
78
Defective outdoor fan motor
Short circuit
Defective radiation fin thermistor
Disconnection of connector
Defective outdoor unit PCB
Silicon grease is not applied properly on the radiation fin after replacing the outdoor unit
PCB.
Service Diagnosis
SiBE041010EA
Troubleshooting
Troubleshooting
Caution
Check No.17
Refer to P.91
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
Turn off the power and turn it on
again to start the system.
Check No.19
Refer to P.92
Error displayed again?
YES
Has the PCB been
replaced?
NO
YES
NO
Check if silicon grease is
applied properly on the
radiation fin. If not, apply
the silicon grease.
Check the radiation fin
temperature.
Above A ˚C?
NO
Replace the outdoor unit
PCB.
YES
Check No. 19
Check the outdoor fan or
related system.
NG
Replace the outdoor fan
motor.
Correct the connectors and
fan motor leads.
Replace the outdoor unit
PCB.
OK
Radiation fin dirty?
Too dirty
Clean up the radiation fin.
Slightly dirty
Check No. 17
Check the installation condition.
(R19119)
A (°C)
93
Note:
Service Diagnosis
Refer to “Silicon Grease on Power Transistor / Diode Bridge” on page 98 for detail.
82
Troubleshooting
SiBE041010EA
4.24 Output Overcurrent Detection
Error Code
L5
Method of Error
Detection
An output overcurrent is detected by checking the current that flows in the inverter DC section.
Error Decision
Conditions
„ A position signal error occurs while the compressor is running.
„ A rotation speed error occurs while the compressor is running.
„ An output overcurrent signal is fed from the output overcurrent detection circuit to the
microcomputer.
„ If the error repeats, the system is shut down.
„ Reset condition: Continuous run for about 11 minutes without any other error
Supposed
Causes
83
„
„
„
„
„
„
„
Poor installation condition
Closed stop valve
Defective power module
Wrong internal wiring
Abnormal power supply voltage
Defective outdoor unit PCB
Defective compressor
Service Diagnosis
SiBE041010EA
Troubleshooting
Troubleshooting
Caution
Check No.15
Refer to P.89
Check No.17
Refer to P.91
Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.
∗ An output overcurrent may result from wrong internal wiring. If the system is interrupted by an output
overcurrent after the wires have been disconnected and reconnected for part replacement, check the
wiring again.
Check No. 17
Check the installation condition.
NO
Stop valve fully open?
Check No.18
Refer to P.91
Check No.22
Refer to P.93
Fully open the stop valve.
YES
Turn off the power and turn it on
again to start the system. See if the
same error occurs.
Error again?
NO Monitor the power supply voltage,
discharge and suction pressures,
and other factors for a long term.
YES
Possible causes
∗ Momentary fall of power supply
voltage
∗ Compressor overload
∗ Short circuit
Turn off the power and disconnect
the harnesses U, V, and W.
Check the connectors and
other components.
∗ Inverter analyzer:
RSUK0917C
Check No.15
Check with the inverter analyzer.
Any LED off?
Keep on using.
YES
Correct the power supply
or replace the outdoor unit
PCB.
NO
Check No. 22
Check the power module.
Normal?
NO
Replace the outdoor unit
PCB.
YES
Turn off the power, and reconnect
the harnesses. Turn on the power
again and start operation.
Check the power supply voltage.
Is the
power supply
voltage fluctuation within
±10% from the rated
value?
NO
Correct the power supply.
YES
Short circuit or
wire breakage between
compressor's coil
phases?
YES
Replace the compressor.
NO
Check No. 18
Check the discharge pressure.
(R18803)
Service Diagnosis
84
Check
SiBE041010EA
5. Check
5.1
Thermistor Resistance Check
Check No.01
Disconnect the connectors of the thermistors from the PCB, and measure the resistance of
each thermistor using tester.
The data is for reference purpose only.
Thermistor temperature (°C)
Resistance (kΩ)
Room temperature thermistor
Other thermistors
–20
–15
73.4
57.0
197.8
148.2
–10
–5
44.7
35.3
112.1
85.60
0
5
28.2
22.6
65.93
51.14
10
15
18.3
14.8
39.99
31.52
20
25
12.1
10.0
25.02
20.00
30
35
8.2
6.9
16.10
13.04
40
45
5.8
4.9
10.62
8.707
50
4.1
7.176
(R25°C = 10 kΩ, B = 3435 K) (R25°C = 20 kΩ, B = 3950 K)
Other thermistors
Room temperature thermistor
(kΩ)
(kΩ)
150
50
100
25
50
0
–15
0
15
30
45
(˚C)
–15
0
Tester
15
30
45
(˚C)
(R11952)
Room temperature
thermistor
Resistance range
Tester
(R17417)
(R18296)
„ When the room temperature thermistor is soldered on a PCB, remove the PCB from the
control PCB to measure the resistance.
„ When the connector of indoor heat exchanger thermistor is soldered on a PCB, remove the
thermistor and measure the resistance.
85
Service Diagnosis
SiBE041010EA
5.2
Check
Fan Motor Connector Output Check
Check No.03
Š
1.
2.
3.
Fan motor wire breakdown / short circuit check
Check the connector for connection.
Turn the power off.
Check if each resistance at the phases U - V and V - W is 90 Ω ~ 100 Ω (between the pins
12 - 9, and between 9 - 6).
Š Motor control voltage check
1. Check the connector for connection.
2. Check the motor control voltage is generated (between the pins 2 - 3).
Š
1.
2.
3.
Rotation pulse check
Check the connector for connection.
Turn the power on and stop the operation.
Check if the Hall IC generates the rotation pulse 4 times when the fan motor is manually
rotated once (between the pins 1 - 3).
S200
Phase U
12
11
Free pin
10
Free pin
Phase V
9
8
Free pin
7
Free pin
6
Phase W
5
Free pin
4
Free pin
3
GND
2
Motor control voltage (15 VDC)
1
Rotation pulse (5 VDC)
(R11979)
Service Diagnosis
86
Check
5.3
SiBE041010EA
Power Supply Waveforms Check
Check No.11
Measure the power supply waveform between No. 1 and No. 2 on the terminal board, and check
the waveform disturbance.
„ Check if the power supply waveform is a sine wave. (Fig.1)
„ Check if there is waveform disturbance near the zero cross. (sections circled in Fig.2)
Fig.1
Fig.2
(R1444)
(R1736)
5.4
Electronic Expansion Valve Check
Check No.12
Conduct the followings to check the electronic expansion valve (EV).
1. Check if the EV connector is correctly connected to the PCB.
2. Turn the power off and on again, and check if the EV generates a latching sound.
3. If the EV does not generate a latching sound in the above step 2, disconnect the connector
and check the continuity using a tester.
4. Check the continuity between the pins 1 - 6, 3 - 6, 2 - 5, 4 - 5 (between the pins 1 - 6, 2 - 6, 3 - 6,
4 - 6 for the harness 5P models). If there is no continuity between the pins, the EV coil is faulty.
5. If the continuity is confirmed in step 3, the outdoor unit PCB is faulty.
Harness 5P
Harness 6P
S20
6P Connector
1 2 3 4 5 6
Check
1-6
3-6
2-5
4-5
S20
(5)
6P Connector
1 2 3 4 5 6
(R16385)
Note:
87
Check
1-6
2-6
3-6
4-6
(R16386)
Please note that the latching sound varies depending on the valve type.
Service Diagnosis
SiBE041010EA
5.5
Check
Four Way Valve Performance Check
Check No.13
Turn off the power and turn it on
again.
∗ Four way valve coil
Cooling / Dry : No continuity
Heating : Continuity
Start heating operation.
S80
voltage at 120 - 220
VDC with compressor
on? (Fig. 1)
NO
Replace the outdoor unit
PCB.
YES
Disconnect the four way valve coil
from the connector and check the
continuity.
Four way
valve coil resistance at
1000 ~ 2000 Ω?
NO
Replace the four way valve
coil.
YES
Replace the four way valve.
(R11965)
(Fig. 1)
Voltage at S80
120 - 220 VDC
3 seconds
Compressor
ON
Time
(R19102)
5.6
Inverter Units Refrigerant System Check
Check No.14
Refrigerant system check
Is the
discharge pipe
thermistor disconnected
from the holder?
YES
Reconnect the thermistor.
NO
Check for refrigerant leakage.
See the service diagnosis on
refrigerant shortage (U0).
Replace the refrigerant.
(R15833)
Service Diagnosis
88
Check
5.7
SiBE041010EA
Inverter Analyzer Check
Check No.15
„ Characteristics
Inverter analyzer: RSUK0917C
If an abnormal stop occurs due to compressor startup failure or overcurrent output when using
an inverter unit, it is difficult to judge whether the stop is caused by the compressor failure or
some other failure (main PCB, power module, etc.). The inverter analyzer makes it possible to
judge the cause of trouble easily and securely. (Connect an inverter analyzer as a quasicompressor instead of compressor and check the output of the inverter)
„ Operation Method
Step 1
Be sure to turn the power off.
Step 2
Connect an inverter analyzer in place of the compressor.
Note:
Make sure the charged voltage of the built-in smoothing electrolytic capacitor drops to 10
VDC or below before carrying out the service work.
(1) Remove the terminals from
the compressor.
(2) Connect the terminals to the
inverter analyzer.
Compressor
Inverter analyzer
Be careful not to let the terminals (U,V,W)
touch each other. Otherwise, high voltage
is applied.
(R18322)
Reference:
If the terminals of the compressor are not FASTON terminals (difficult to remove the wire on
the terminals), it is possible to connect wires available on site to the outdoor unit from the
output side of the PCB. (Do not connect the wires to the compressor at the same time,
otherwise it may result in incorrect detection.)
Step 3
Activate power transistor test operation from the indoor unit with the remote controller.
(1) Turn the system on.
(2) Select FAN operation with the [MODE] button on the remote controller.
(3) Press the center of the [TEMP] button and the [MODE] button at the same time.
→ 00 is displayed with the figure of ten's place blinking.
(4) Press the [MODE] button.
→ 00 is displayed with the figure of one's place blinking.
(5) Press the [MODE] button.
→ T is displayed.
(6) Press the [ON/OFF] button.
→ Power transistor test operation starts.
89
Service Diagnosis
SiBE041010EA
Check
„ Diagnose method (Diagnose according to 6 LEDs lighting status.)
(1) If all the LEDs are lit uniformly, the compressor is defective.
→ Replace the compressor.
(2) If the LEDs are not lit uniformly, check the power module.
→ Refer to Check No.22.
(3) If NG in Check No.22, replace the power module.
(Replace the main PCB. The power module is united with the main PCB.)
If OK in Check No.22, check if there is any solder cracking on the PCB.
(4) If any solder cracking is found, replace the PCB or repair the soldered section.
If there is no solder cracking, replace the PCB.
Caution
(1) When the output frequency is low, the LEDs blink slowly. As the output frequency increases,
the LEDs blink quicker. (The LEDs look like they are lit.)
(2) On completion of the inverter analyzer diagnosis, be sure to re-crimp the FASTON terminals.
Otherwise, the terminals may be burned due to loosening.
Direction of crimp
This size is shortened
by the crimp.
FASTON terminal
(R15292)
5.8
Rotation Pulse Check on the Outdoor Unit PCB
Check No.16
1. Check that the voltage between the pins 10 - 11 is 15 VDC.
2. Check if the Hall IC generates the rotation pulse (0 ~ 15 VDC) 4 times between the pins 10 12, 10 - 13, when the fan motor is manually rotated once.
S70
13
HV (Hall IC)
12
HU (Hall IC)
11
15 VDC
10
9
Free pin
8
Free pin
Phase W
7
6
Free pin
5
Free pin
Phase V
4
3
Free pin
2
Free pin
1
Phase U
(R11907)
Service Diagnosis
90
Check
5.9
SiBE041010EA
Installation Condition Check
Check No.17
Installation condition check
Check the allowable
dimensions of the air
suction and
discharge area.
NG
Change the installation
location or direction.
OK
Is the discharged air
short-circuited?
YES
Change the installation
location or direction.
NO
Is the outdoor heat
exchanger very dirty?
YES
Clean the outdoor heat
exchanger.
NO
Is the airflow blocked by
obstacles or winds
blowing in the opposite
direction?
YES
NO
Change the installation
location or direction.
Check the outdoor temperature.
(The outdoor temperature
should be within the operation
range.)
(R17537)
5.10 Discharge Pressure Check
Check No.18
Discharge pressure check
High?
NO
Replace the compressor.
YES
Is the stop valve open?
NO
Open the stop valve.
YES
Is the connection pipe
deformed?
YES
Replace the pipe installed at
the site.
NO
Is the air
filter or indoor / outdoor
heat exchanger
dirty?
Not dirty
Dirty
Clean the dirty air filter or
indoor / outdoor heat
exchanger.
Replace the compressor.
(R15738)
91
Service Diagnosis
SiBE041010EA
Check
5.11 Outdoor Fan System Check
Check No.19
DC motor
Check the outdoor fan system.
Fan motor
lead wire connector
disconnected?
NO
Outdoor fan running?
YES
YES
Reconnect the connector.
NO
Go to Check No. 16.
Outdoor fan system is functioning.
(R15001)
5.12 Main Circuit Short Check
Check No.20
Note:
Make sure that the voltage between (+) and (–) of the diode bridge (DB1) is approximately
0 V before checking.
„ Measure the resistance between the pins of the DB1 referring to the table below.
„ If the resistance is ∞ or less than 1 kΩ, short circuit occurs on the main circuit.
Positive (+) terminal of
tester (negative terminal
(–) for digital tester)
Resistance is OK.
Resistance is NG.
~ (2, 3)
+ (4)
~ (2, 3)
– (1)
+ (4)
~ (2, 3)
– (1)
~ (2, 3)
several kΩ
~ several MΩ
∞
∞
several kΩ
~ several MΩ
0 Ω or ∞
0
0
0 Ω or ∞
2
3
4
– ~ ~ +
1
– +
Negative (–) terminal of
tester (positive terminal
(+) for digital tester)
Tester
(R19120)
Service Diagnosis
92
Check
SiBE041010EA
5.13 Power Module Check
Check No.22
Note:
Make sure that the voltage between (+) and (–) of the power module is approximately 0 V
before checking.
„ Disconnect the compressor harness connector from the outdoor unit PCB. To disengage the
connector, press the protrusion on the connector.
„ Follow the procedure below to measure resistance between the terminals of the power
module and the terminals of the compressor with a multi-tester. Evaluate the measurement
results referring to the following table.
Negative (–) terminal of
tester (positive terminal
(+) for digital tester)
Power module
(+)
UVW
Power module
(–)
UVW
Positive (+) terminal of
tester (negative terminal
(–) for digital tester)
Resistance is OK.
UVW
Power module
(+)
UVW
Power module
(–)
Resistance is NG.
several kΩ ~ several MΩ
0 Ω or ∞
Power module
(R19121)
93
Service Diagnosis
SiBE041010EA
Part 7
Tips for Servicing
1. Tips for Servicing ..................................................................................95
1.1 Pump Down Operation ...........................................................................95
1.2 Forced Cooling Operation ......................................................................95
2. Trial Operation ......................................................................................96
3. Field Settings ........................................................................................97
3.1 When 2 Units are Installed in 1 Room....................................................97
3.2 Jumper Settings .....................................................................................97
4. Silicon Grease on Power Transistor / Diode Bridge..............................98
Tips for Servicing
94
Tips for Servicing
SiBE041010EA
1. Tips for Servicing
1.1
Pump Down Operation
Outline
In order to protect the environment, be sure to conduct pump down operation when relocating or
disposing the unit.
Detail
1) Remove the valve caps from the liquid stop valve and the gas stop valve.
2) Carry out forced cooling operation.
3) After 5 to 10 minutes, close the liquid stop valve with a hexagonal wrench.
4) After 2 to 3 minutes, close the gas stop valve and stop the forced cooling operation.
Hexagonal
wrench
Close
Liquid stop valve
Gas stop valve
Service port
Valve cap
(R13628)
Refer to forced cooling operation below.
1.2
Forced Cooling Operation
Item
Conditions
Forced Cooling
The forced cooling operation is allowed when both of the following conditions
are met.
1) The outdoor unit is not abnormal and not in the 3-minute standby mode.
2) The outdoor unit is not operating.
Start
Command
frequency
End
Press the forced cooling operation [ON/OFF] button (SW1) on the indoor unit
for 5 seconds.
58 Hz
The forced cooling operation ends when any of the following conditions is fulfilled.
1) The operation ends automatically after 15 minutes.
2) Press the forced cooling operation [ON/OFF] button (SW1) on the indoor
unit again.
3) Press the [ON/OFF] button on the remote controller.
Others
Protection functions have priority over all other functions during forced cooling
operation.
Indoor Unit
[ON/OFF] button (SW1)
(R19103)
Caution
95
When pressing the button, do not touch the terminal board. It has a high voltage and may cause
electric shock.
Tips for Servicing
SiBE041010EA
Trial Operation
2. Trial Operation
Outline
1. Measure the power supply voltage and make sure that it falls within the specified range.
2. Trial operation should be carried out in either cooling or heating operation.
In cooling operation, select the lowest programmable temperature (18°C); in heating
operation, select the highest programmable temperature (30°C).
Š Trial operation may be disabled in either operation mode depending on the room
temperature.
Š After trial operation is complete, set the temperature to a normal level.
(26°C ~ 28°C in cooling, 20°C ~ 24°C in heating)
Š For protection, the system does not start for 3 minutes after it is turned off.
3. Carry out the trial operation in accordance with the operation manual to ensure that all
functions and parts, such as flap movement, are working properly.
Note:
„ The air conditioner requires a small amount of power in standby mode. If the system is not to
be used for some time after installation, shut off the circuit breaker to eliminate unnecessary
power consumption.
„ If the circuit breaker trips to shut off the power to the air conditioner, the system backs up the
operation mode. The system then restarts operation with the previous operation mode when
the circuit breaker is restored.
Detail
ARC433 Series
(1) Press the [ON/OFF] button to turn on the system.
(2) Press the center of the [TEMP] button and the [MODE] button at the same time.
(3) Press the [MODE] button twice.
(T appears on the display to indicate that trial operation is selected.)
(4) Press the [MODE] button and select operation mode.
(5) Trial operation terminates in approx. 30 minutes and switches into normal mode. To quit trial
operation, press the [ON/OFF] button.
(3)
(2)
(1) (5)
(2) (3) (4)
Tips for Servicing
(R19104)
96
Field Settings
SiBE041010EA
3. Field Settings
3.1
When 2 Units are Installed in 1 Room
Outline
When 2 indoor units are installed in 1 room, 1 of the 2 indoor units and the corresponding
wireless remote controller can be set for different addresses.
Both the indoor unit PCB and the wireless remote controller need alteration.
Indoor Unit PCB
„ Cut the address setting jumper JA on the control PCB.
JA
JA ADDRESS
EXIST
CUT
1
2
(R12007)
Caution
Wireless Remote
Controller
Replace the PCB if you accidentally cut a wrong jumper.
Jumpers are necessary for electronic circuit. Improper operation may occur if you cut any of them.
„ Cut the address setting jumper.
Jumper
EXIST
CUT
3.2
Address
1
2
(R14202)
Jumper Settings
Indoor Unit
Jumper
Function
JB
Fan speed setting
when compressor
stops for thermostat
OFF. (effective only in
cooling operation)
JC
Power failure
recovery function
When connected
(factory setting)
Fan speed setting;
Remote controller
setting
Auto-restart
When cut
Fan speed setting; “0” (The fan stops.)
The unit does not resume operation after
recovering from a power failure. Timer
settings are cleared.
Outdoor Unit
Jumper
J5
Caution
97
Function
Improvement of
defrost performance
When connected
(factory setting)
Standard control
When cut
Reinforced control
(ex. The frequency increases, the
duration time of defrost lengthens.)
Replace the PCB if you accidentally cut a wrong jumper.
Jumpers are necessary for electronic circuit. Improper operation may occur if you cut any of
them.
For the location of the jumper, refer to the following pages.
Indoor unit: P.14.
Outdoor unit: P.16.
Tips for Servicing
SiBE041010EA
Silicon Grease on Power Transistor / Diode Bridge
4. Silicon Grease on Power Transistor / Diode
Bridge
Outline
Apply the specified silicon grease to the heat radiation part of a power transistor / diode bridge
when you replace an outdoor unit PCB. The silicon grease encourages the heat radiation of a
power transistor / diode bridge.
Detail
1.
2.
3.
4.
Wipe off the old silicon grease completely.
Apply the silicon grease evenly. See the illustrations below for examples of application.
Tighten the screws of the power transistor / diode bridge.
Make sure that the heat radiation parts are firmly contacted to the radiation fin.
Note: Smoke emission may be caused by bad heat radiation when the silicon grease is not
appropriately applied.
„ OK: Evenly applied
Power transistor
(or diode bridge)
PCB
Radiation
fin
Silicon grease
(R18015)
„ NG: Not evenly applied
(R18016)
„ NG: Foreign matter is stuck.
Foreign matter
Tips for Servicing
(R18017)
98
SiBE041010EA
Part 8
Appendix
1. Piping Diagrams..................................................................................100
1.1 Indoor Unit............................................................................................100
1.2 Outdoor Unit .........................................................................................101
2. Wiring Diagrams..................................................................................102
2.1 Indoor Unit............................................................................................102
2.2 Outdoor Unit .........................................................................................102
3. Removal Procedure (Booklet No.) ......................................................103
99
Appendix
SiBE041010EA
Piping Diagrams
1. Piping Diagrams
1.1
Indoor Unit
FTX20/25/35JV1B, FTX20/25/35J2V1B, ATX20/25/35JV1B, ATX20/25/35J2V1B
INDOOR UNIT
HEAT EXCHANGER
7.0CuT
7.0CuT
4.8CuT
THERMISTOR
ON HEAT EXCH.
7.0CuT
7.0CuT
FIELD PIPING
(6.4CuT)
CROSS FLOW FAN
M
FAN MOTOR
FIELD PIPING
(9.5CuT)
9.5CuT
REFRIGERANT FLOW
COOLING
HEATING
4D058926R
Appendix
100
Piping Diagrams
1.2
SiBE041010EA
Outdoor Unit
RX20/25JV1B, RX20/25J3V1B, ARX20/25JV1B, ARX20/25J3V1B
OUTDOOR UNIT
9.5CuT
7.0CuT
OUTDOOR TEMPERATURE
THERMISTOR
HEAT EXCHANGER
7.0CuT
HEAT EXCHANGER
THERMISTOR
6.4CuT
6.4CuT
MOTOR OPERATED
VALVE
6.4CuT
7.0CuT
MUFFLER
WITH
FILTER
MUFFLER
WITH
FILTER
M
9.5CuT
PROPELLER FAN
FOUR WAY
VALVE
ON: HEATING
LIQUID STOP
VALVE
FIELD PIPING
(6.4CuT)
6.4CuT
DISCHARGE PIPE
THERMISTOR
9.5CuT
4.8CuT
9.5CuT
9.5CuT
9.5CuT
COMPRESSOR
ACCUMULATOR
GAS STOP
VALVE
MUFFLER
FIELD PIPING
(9.5CuT)
REFRIGERANT FLOW
COOLING
HEATING
C: 3D058716C
RX35JV1B, RX35J3V1B, ARX35JV1B, ARX35J3V1B
OUTDOOR UNIT
OUTDOOR TEMPERATURE
THERMISTOR
9.5CuT
7.0CuT HEAT EXCHANGER
7.0CuT
HEAT EXCHANGER
THERMISTOR
7.0CuT
6.4CuT
MOTOR OPERATED
VALVE
6.4CuT
MUFFLER
WITH
FILTER
M
6.4CuT
7.0CuT
MUFFLER
WITH
FILTER
9.5CuT
PROPELLER FAN
FOUR WAY
VALVE
ON: HEATING
6.4CuT
DISCHARGE PIPE
THERMISTOR
9.5CuT
4.8CuT
9.5CuT
LIQUID STOP
VALVE
9.5CuT
COMPRESSOR
ACCUMULATOR
9.5CuT
MUFFLER
GAS STOP
VALVE
FIELD PIPING
(6.4CuT)
FIELD PIPING
(9.5CuT)
REFRIGERANT FLOW
COOLING
HEATING
C: 3D058714C
101
Appendix
SiBE041010EA
Wiring Diagrams
2. Wiring Diagrams
2.1
Indoor Unit
FTX20/25/35JV1B, FTX20/25/35J2V1B, ATX20/25/35JV1B, ATX20/25/35J2V1B
PCB 2
S27
1
BLK
LED1
H1P
BLK
LED2
H2P
BLK
BLK
BLK
9
BLK
PCB 1
S26
9
FIELD WIRING.
TRANSMISSION
CIRCUIT
BLK
GRN/YLW
FG
BLK
BLK
_
1
RECTIFIER
H3
+
V1
MR10
3
GRN
H2
H1
S1W
3
WHT
2
BLK
_
R1T
SIGNAL
RECEIVER
2
1
1
5
S6
+
9
S403
1
12
10
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
WHT
BLK BLK BLK
BLK
INDOOR
RED
BLK BLK
BLK BLK
6
S200
ORG
YLW
BLU
1
1 4
1
6
M
M
t˚
OUTDOOR
CAUTION
NOTE THAT OPERATION WILL
RESTART AUTOMATICALLY IF
THE MAIN POWER SUPPLY IS
TURNED OFF AND THEN BACK
ON AGAIN.
X1M
IPM200
S32
WIRELESS
REMOTE
CONTROLLER
1
1
F1U
3.15A
t˚
M1S
S602
S601
FG
F1U
H1~H3
H1P~H2P
M1F
M1S
PCB1~PCB3
R1T, R2T
S6~S602
S1W
X1M
M1F
R2T
S21
NOTE)
1. PCB3 SHOWS THE CASE OF
OPTION CONNECTION.
PCB 3
OPTION
2.2
2
RED
: FRAME GROUND
: FUSE
: HARNESS
: PILOT LAMP
: FAN MOTOR
: SWING MOTOR
: PRINTED CIRCUIT BOARD
: THERMISTOR
: CONNECTOR
: OPERATION SWITCH
: TERMINAL STRIP
: PROTECTIVE EARTH
3D058454B
Outdoor Unit
RX20/25/35JV1B, RX20/25/35J3V1B, ARX20/25/35JV1B, ARX20/25/35J3V1B
FIELD WIRING.
MRM10
HN2
V2
HN3
GRN/YLW
N
SA1
1
GRN
PCB1
9
+
C5 +
C6 -
~ -
FU1
3.15A
V1
1
DB3
~ +
S10
~ 9
S20
S40
1
6
2 1
WHT
YLW
ORG
BLU
BRN
RED
GRN
OUTDOOR
E2
S11
WHT
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
+
DB2
~ +
~ -
ORG
MR30
E1
Z2C
N=2
HA2
GRY
HL3
HL2
IPM1
HR2 DB1
~ +
HA1
BLU
V3
L
WHT
+
- C119
W V U
FU2
MR4 3.15A
PCB2
PTC1
+t˚
S90
1
6
1 S80 3
1
3
Y1R
NOTE
S80
IN CASE OF
1. REFER TO THE NAMEPLATE FOR THE POWER REQUIREMENTS.
IN CASE OF
t˚
t˚
t˚
M
HEAT
PUMP
: CAPACITOR
C5, C6, C119
COOLING ONLY
TYPE
Q1L
: DIODE BRIDGE
DB1, DB2, DB3
Y1E
TYPE
R1TR2TR3T
: FUSE
FU1, FU2, FU3
(OUTDOOR)
(DISCHARGE)
: INTELLIGENT POWER MODULE
IPM1, IPM2
(CONDENSER)
: LIVE
L
: OVERLOAD PROTECTOR
Q1L
: COIL
SA1
L1
: PRINTED CIRCUIT BOARD
PCB1, PCB2
: REACTOR
V1, V2, V3
L1R
: THERMISTOR PTC
PTC1
: COMPRESSOR MOTOR
X1M
M1C
S10, S11, S20, S40
: FAN MOTOR
Y1E
M1F
S70, S80, S90, HL3
Y1R
MR4, MR30, MRM10
: CONNECTOR
HN3
: MAGNETIC RELAY
Z1C, Z2C
MRM20
: THERMISTOR
R1T, R2T, R3T
: NEUTRAL
N
IPM2
+
-
S70
1 4 7 10111213
3
M
1~
M1F
RED
S
L1R
BRN
YLW
AC2
L1
BLU
WHT
RED
AC1 20A
GRY
BLK
YLW
RED
WHT
BLK
BRN
ORG
BLU
MRM20
HR1
FU3
X1M
L 1
N 2
3
BLK
BLK
BLK
BLK
BLK
BLK
1
2
3
BLK
INDOOR
1
Z1C
V N=3
W
U
M1C
: SURGE ARRESTER
: VARISTOR
: TERMINAL STRIP
: ELECTRONIC EXPANSION VALVE COIL
: REVERSING SOLENOID VALVE COIL
: FERRITE CORE
: PROTECTIVE EARTH
3D058406D
Appendix
102
Removal Procedure (Booklet No.)
SiBE041010EA
3. Removal Procedure (Booklet No.)
Refer to the following booklets for removal procedure.
103
∗FTX20/25/35JV1B, ATX20/25/35JV1B
Refer to Si041051.
∗FTX20/25/35J2V1B, ATX20/25/35J2V1B
Refer to Si041264.
∗RX20/25/35JV1B, ARX20/25/35JV1B
Refer to Si001073.
∗RX20/25/35J3V1B, ARX20/25/35J3V1B
Refer to Si001276.
Appendix
Revision History
Month / Year
Version
03 / 2010
SiBE041010
06 / 2013
SiBE041010EA
Revised contents
First edition
Model addition: FTX20/25/35J2V1B, ATX20/25/35J2V1B, RX20/25/35J3V1B,
ARX20/25/35J3V1B
Warning
z Daikin products are manufactured for export to numerous countries throughout the world. Prior to
purchase, please confirm with your local authorised importer, distributor and/or retailer whether this
product conforms to the applicable standards, and is suitable for use, in the region where the product
will be used. This statement does not purport to exclude, restrict or modify the application of any local
legislation.
z Ask a qualified installer or contractor to install this product. Do not try to install the product yourself.
Improper installation can result in water or refrigerant leakage, electrical shock, fire or explosion.
z Use only those parts and accessories supplied or specified by Daikin. Ask a qualified installer or
contractor to install those parts and accessories. Use of unauthorised parts and accessories or
improper installation of parts and accessories can result in water or refrigerant leakage, electrical
shock, fire or explosion.
z Read the User's Manual carefully before using this product. The User's Manual provides important
safety instructions and warnings. Be sure to follow these instructions and warnings.
If you have any enquiries, please contact your local importer, distributor and/or retailer.
Cautions on product corrosion
1. Air conditioners should not be installed in areas where corrosive gases, such as acid gas or alkaline gas, are produced.
2. If the outdoor unit is to be installed close to the sea shore, direct exposure to the sea breeze should be avoided. If you need to install
the outdoor unit close to the sea shore, contact your local distributor.
Dealer
Head Office:
Umeda Center Bldg., 2-4-12, Nakazaki-Nishi,
Kita-ku, Osaka, 530-8323 Japan
Tokyo Office:
JR Shinagawa East Bldg., 2-18-1, Konan,
Minato-ku, Tokyo, 108-0075 Japan
http://www.daikin.com/global_ac/
c All rights reserved
zSpecifications, designs and other content appearing in this brochure are current as of June 2013 but subject to change without notice.
SiBE041010EA
06/2013 AK.B
Download PDF

advertising