Video Signal Equipment
CCTV
Video Signal Equipment | 219
Video Signal Equipment
www.boschsecuritysystems.com
220 | Video Signal Equipment
VMD01 Digital Motion Detector
CCTV
Technical Specifications
Electrical
Power Supply
Type
External plug power adapter VMD-PS90
or integrated in a 19-inch rack VMD-RA90
Operating voltage
5 VDC
Power consumption
6W
Connection
RJ12 (+5 V to 1.2; GND to 4.6)
Video
Input
1 x BNC, VMD01-M50: PAL/CCIR,
VMD01-M60: NTSC/EIA, 75 Ohm (internal
termination), 1 Vss
(0.5 – 2.0 Vss)
Output
1 x BNC, VMD01-M50: PAL/CCIR,
VMD01-M60: NTSC/EIA, 1 Vss; live
images, live images with outlined
objects, stored alarm images, GUI for set up
Contacts
Inputs
Internal pull up to ground;
1.: arm/disarm sensor;
2.: toggle parameter set
Whenever you need reliable video motion detection, for indoor
or outdoor use, the Bosch VMD01 is the unit of choice.
The VMD01 is an intelligent digital motion detector that uses
advanced video content analysis to reliably detect moving
objects while suppressing unwanted alarms from spurious
sources in the image. The unit intelligently adapts to changing
lighting and environmental conditions such as rain, snow and
leaves blowing in the wind.
The MD01 can easily be configured to select the sensitive areas
of the image, the minimum object size and the motion direction
that will trigger an alarm, so that it only detects the important
moving objects in a scene. A Graphical display allows the
sensitive area, size and perspective for objects, and movement
direction to be simply drawn on the image. Once movement has
been detected, the object causing the alarm is outlined on the
screen, the motion tracked on the monitor, and pre and post
alarm images are stored. The alarm condition can be signaled by
means of a standard relay output and LED on the unit.
The stored alarm images can be replayed on the monitor using
the front panel rotary switch or by remote control.
Outputs
Open collector, 100 mA, 12 V;
1. object detection; adjustable at peak, perodic peak
or as long as object is detected;
2. video signal supervision
Relay
Output
30 V max., 1.0 A; 1.: system/common failure
(break contact); 2.: object detection, until reset
(minimal for 1 second)
LED
Conditions
1.: (Green) Power on, system failure,
Indicated
2.: (Red) detector armed, video loss, object detection
Serial Port
Type
RS232, 115 kBaud max. (for back-up purposes,
connection of mouse)
VMD
Type
Digital image analysis; multi-level changes in
illumination, texture and motion; primarily outdoor
applications (indoor use acceptable)
Results
Superimposed in video-out signal, yellow outline =
Display
initial position; red outline = present position; green =
trajectory (B/W-lines if B/W signal at video-in)
Features
Alarm Image Storage
• Intelligent digital video motion detector
Alarm
5 pre-alarm images, 1 alarm image, 10 post-alarm
• Detects, tracks and stores motion images
Images
images
• Automatic self-adaptation to changing environmental
conditions
VMD results
Super imposed outlines, fade out after 5 seconds
Access
Via rotary switch on front panel or remote controlled
• Maximizes detection rate and reduces unwanted alarms
(toggle) between live image and image storage;
forward and backward stepping
• Stand alone or system integration
Operation Modes
• Intuitive graphical interface for fast effective set up
1 Reset of alarms
Parts Included
Quant.
1
Component
VMD01
www.boschsecuritysystems.com
automatic
Normal operation
live image on video-out;
Object detection
Super imposed outlines in live image on
video-out (last alarm sequence in storage)
2 Reset of alarms
Normal operation
manual
live image on video-out;
CCTV
Video Signal Equipment | 221
Electrical
Object detection
3 Reset of alarms
Environmental
Super imposed outlines in live image on
Operating temperature
0°C to 45°C (32°F to 113°F)
video-out (first, not reset alarm sequence in
Humidity in operation
8% to 80% relative, non condensing
storage)
Accessories included
Manual
15pin D-sub plug, 4 rubber feet for desk top mount, 4 locking springs
Normal operation
live image on video-out
for stack mount
Object detection:
automatic switchover to the alarm image
Type number
Description
storage / first alarm image with
VMD-PS90
Power supply (required if using as single stand-
superimposed outlines on video-out (first,
alone unit) 100 – 240 VAC / 5 VDC, max. 2,4
not reset alarm sequence in storage),
A. cord 2,0 m, 4x 0.6 with RJ11 plug(+5 V to
1.2; GND to 4.6).
Security
Passcode
Five (5) digits
Video Signal -
Signal loss, bad signal-to-noise ratio, camera
Supervision
blinded, insufficient scene illumination
Europe and AUS
Dimensions
appr. 85 x 50 x 32 mm
(H x W x D)
(depth without contacts).
EN 50081-1, EN 50130-4, EN50130-5, EN
VMD-SM
Serial mouse (required for set-up)
60950, FCC, UR
VMD-RA90
19-inch rack mount enclosure with power
Compliance
Emissions & Safety
four (4) different adapters included for UK, US,
Mounting Possibilities
supply for up to eight VMD01s, 3VU, depth:
Desk top (stand alone or as stack), wall or ceiling mounted (use VMD-
378 mm (including eight bracket sets for
WM), 19 inch rack mounted (use VMD-RA90 or VMD-RA00)
VMD01 mounting)
Power supply:
Mechanical
Dimensions
(H x W x D)
Weight
primary 110 – 230 VAC, Euro and US power
cord (1.5 m), secondary 8x5 VDC, 8x 2A
(including cable set)
110 x 48 x 207 mm
(4,3 x 1,88 x 8.1 inch)
VMD-RA00
Like VMDRA90, but without power supply
0.5 kg
VMD-RADC
Set of four front panel covers for one slot of the
19-inch rack
(without mouse & power supply)
www.boschsecuritysystems.com
VMD-WM
Wall mount bracket for one stand-alone unit,
Dimensions
165 x 205 x 10 mm
(H x W x D)
(6.6 x 8.05 x 0.39 inch)
Weight
0.4 kg.
222 | Video Signal Equipment
LTC 5231 & LTC 5234 Series
CCTV
Technical Specifications
Electrical
LTC 5231Series
LTC 5234 Series
Single-Channel
Four-Channel
Model No.
/50
/60
/60
/50
Rated Voltage
230 VAC
120 VAC
120 VAC
230 VAC
50/60 Hz
50/60 Hz
50/60 Hz
50/60 Hz
198 to
105 to 130
Voltage Range
198 to 264
264
Power at
5W
6W
Video Inputs
One (1)
Four (4)
Signal Range
0.5 Vp-p to 2.0 Vp-p
Video Outputs
Four (4)
Twelve (12)
isolated, 75 Ohm.
75 Ohm.
Rated Voltage
Video Gain
Unity.
Signal-to-
65 dB typical.
Noise
Bandwidth
The LTC 5231 Series and LTC 5234 Series are video distribution
amplifiers. They provide video outputs identical to the video input
for use with other video equipment.
The LTC 5231Series are single-channel video distribution
amplifiers. They provide four (4) video outputs identical to a
single video input for use with other video equipment.
A front panel LED is provided to indicate when the amplifier is
receiving video. In the event of loss of video,
the LTC 5231 Series amplifiers provide a relay contact closure
output to signal this occurrence. The LTC 5234 Series are
4-channel video distribution amplifiers. They provide four
distribution amplifiers each having one input and three outputs.
Each of the four amplifiers provides three (3) video outputs
identical to a single video input for use with other video
equipment. Inputs have selectable termination permitting looping
of the video signal. This feature allows a single video signal to be
distributed to as many as 12 devices when all four distribution
amplifiers are used. A front panel LED is provided for each
distribution amplifier to indicate when the amplifier is receiving
video. Each of the four channels of the LTC 5234 Series also
include a relay contact closure output to signal video loss.
These units are supplied as desktop units; rack mount kits are
available for rack mounting.
Features
• Video Presence Indicators
• Video Loss Contact Closure
• No User Adjustments
• Easy Installation
• Optional Rack Mounting
• Color Compatible
www.boschsecuritysystems.com
20 MHz typical
25 MHz typical
-3 dB Point
Differential
0.5% typical.
Gain
Differential
0.6 degrees typical.
1.2 degrees typical.
Relay contact pair.
4 Relay contact pair.
Phase
Video Loss
Output
Rating
1 ampere at 40 volts AC / DC maximum.
Indicators
Power on LED
Green
video
Green
presence LED
Connectors
BNC (5).
BNC (16).
CCTV
Video Signal Equipment | 223
Mechanical
Construction
Steel chassis, sheet metal cover & plastic bezel.
Finish
Charcoal.
Dimensions
223 x 280 x 40 mm (8.77 x 11 x 1.59 inch).
(W x H x D)
Weight
LTC 5231 series
2 kg, (4.5 lb)
LTC 5234 series
3 Kg, (6.5lb)
Environmental
OperatingTemperature
0°C to 50°C (32°F to 122°F).
Humidity
10% to 80% relative, non condensing
Electromagnetic Compatibility
EMC Requirements
CE Immunity, CE Emission Class B, FCC
Class B,ICES-003.
Safety:
CE, UL, cUL.
Options
LTC 9101/00 Rack Kit
For mounting one or two units in an EIA
19-inch rack
Height
1 standard rack unit
Width
1 standard rack unit
Ordering Information
Model & Description
LTC5231/60
Distribution amplifier, 1 input, 4 output, 115 V 60 Hz
LTC5231/50
Distribution amplifier, 1 input, 4 output, 230 V 50 Hz
LTC5234/60
Distribution amplifier, 4 input, 12 output (3 per input), 115 V 60 Hz
LTC5234/50
Distribution amplifier, 4 input, 12 output (3 per input), 230 V, 50 Hz
www.boschsecuritysystems.com
224 | Video Signal Equipment
Digital Motion Detectors Indoor
CCTV
Functions
Eight fully adjustable detection zones make these units versatile
and adaptable to nearly any indoor surveillance situation.
Microprocessor based on-screen setup menus allow easy
adjustment of the detection areas. For ease of installation,
on-screen menus can be viewed in any of six languages English, French, German, Spanish, Dutch, or Italian.
Other controls include manual or auto reset, on/off tracer
display, and alarm bypass. LEDs indicate alarm ready, alarm
activation, and power on.
Upon detection of motion, the LTC 2210 Series units react with
an audio beeper and a flashing LED alerting the operator;
alerted cameras are called up on-screen (when used with a
Sequential Switcher); contacts close for operation of master
alarm or VCR operation; and tracers display detected motion.
Sensitivity settings can be adjusted for optimum performance
under a variety of conditions. By adjusting the sensitivity and
percentage movement settings appropriately,
the LTC 2210 Series can effectively discriminate between a
variety of background scenes and desired alarms.
The LTC 2210 Series video motion detectors utilize edge
detection with digital tracing technology. Patented circuitry
provides reliable security surveillance protection.
These economical, full featured single channel detectors provide
flexible operation to maximize performance and minimize false
alarms.
Alarm outputs are available on a 15 pin connector at the rear of
the unit. In addition, this connector provides an input which
when active will arm the unit.
These units are available in 120 VAC or 230 VAC models, single
looping video input, NTSC or PAL color compatibility, desk top
or 1/2-rack mount versions, and a coordinated design which
integrates well with other Bosch switcher products.
Features
• Designed for Indoor Detection
Parts Included
• User Customized Selectable Zones With 12 Sensitivity
Settings
Quant.
Component
1
LTC 2210 (50/60)
• Motion "Tracers"
• On-Screen Programming in Multiple Languages
• Auto-Terminating Looping Inputs
• Remote Arm Input
www.boschsecuritysystems.com
CCTV
Video Signal Equipment | 225
Technical Specifications
Electrical
Mechanical
Finish
Charcoal
Rated
Voltage
Power at
Dimensions
223 x 280 x 40 mm
Voltage
Range
Rated Voltage
(W x H x D)
(8.77 x 11.0 x1.59 inch)
LTC2210/60
120 VAC,
50 / 60 Hz
105 to 130
4W
Weight
2 kg, (4.5 lb)
LTC2210/50
230 VAC,
50 / 60 Hz
195.5 to 253
4W
Evironmental
Model
No.
Video Inputs:
One (1) looping.
Range:
0.5 Vp-p to 2.0 Vp-p.
Impedance:
Automatically switching 75 ohm terminated or
high impedance looping.
Video Outputs
One (1).
Video Gain
Unity.
Bandwidth (-3 dB
12 MHz typical.
point)
Differential Gain
3% typical.
Differential
3° typical.
Phase
Alarm Outputs
Open collector and/or normally open contact closure. The relay
contacts are rated at 1.0 A at 40V AC/DC and a resistive load of 10
VA maximum.
Controls
ALM CLR/ESC Key
Clears an alarm. Cancels beeper, blinking alarm LED, and contact
closure. Unit remains in the pre-alarm state (reset and arm are not
changed). When programming the system, this button can be used to
exit from the programming menus.
ALARM LED
On when armed, blinks when alarm is triggered.
SETUP/ENTER Key
Pressing SETUP/ENTER places the on-screen programming menus
on the video monitor. This key is also used to access sub-menus
during programming.
Direction Keys
These keys are used to navigate through the programming options.
They are also used to define the detection zones.
Detection Zones
Using the arrow keys, detection zones can be drawn anywhere over
the full active video for PAL or NTSC. Minimum detection size is 15%
H x 15% V (2% of screen area). Maximum size is the entire active
video. Detection zones are created on a 64 element (H) by30 element
(V) grid for NTSC and on a 64 element (H) by 36 element (V) for PAL.
Indicators
POWER on LED (Green).
ALARM LED (Red).
Cable (Included) Cable with 15-pin connector on one end.
www.boschsecuritysystems.com
Operating Temperature
0°C to +50°C (32°F to +122°F)
Storage Temperature
-40°C to +60°C (-40°F to +140°F)
Humidity
10% to 80% relative, non condensing
Vibration
3g swept sine wave, 15Hz to 2000Hz.
Shock
50 g, 11 ms, 1/2 sine.
Electromagnetic Compatibility
EMC Requirements
CE Immunity, CE Emission Class B,
FCC Class B, ICES-003.
Safety
CE, UL, cUL.
Ordering Information
Model & Description
LTC2210/60
Single channel motion detector, 120 VAC, 60 Hz
LTC2210/50
Single channel motion detector, 230 VAC, 50 Hz
226 | Video Signal Equipment
Digital Motion Detectors Outdoor
CCTV
Upon alarm, the LTC 2211 Series and LTC 2212 Series provide
on-screen indications to identify the area of intrusion. External
connections provide individual camera alarm outputs, plus one
output that is common to all cameras. A selectable audible tone
activates to alert the operator of alarm conditions, including loss
of video. Individual camera titling with time/date is also provided.
These units can be rack mounted; the coordinated design allows
integration with other Bosch switcher products.
Features
• Designed for Outdoor Detection
• User Customized Selectable Zones
• Direction Sensing and Target Speed Settings
• On-screen Programming in Multiple Languages
• Auto-terminating Looping Inputs
• Timed or Manual Selection of Four Pre-programmed Setup
Parameters
The LTC 2211 Series and LTC 2212 Series are high sensitivity
Digital Motion Detectors. Their ability to ignore environmental
changes and camera vibration make them ideal for use outdoors
as well as indoors. These detectors minimize false alarms via
image processing algorithms, which analyze movement, instead
of simple detection.
The LTC 2211 Series has four camera inputs while the
LTC 2212 Series has eight camera inputs. They are designed for
stand-alone usage, or in conjunction with a switcher/controller
system. All include two monitor outputs. The main output is used
for system setup, alarm call-up, and system information
monitoring. The second bridging output sequences between
cameras.
Setup is simple, via on-screen menus at the main monitor, and
control is easily accomplished using the front panel controls.
The installation menu screens are viewable in six languages English, French, German, Spanish, Dutch, or Italian.
The LTC 2211/60 and LTC 2212/60 feature 1200 detection
points per camera; the LTC 2211/50 and the LTC 2212/50
feature 1120 separate detection points per camera. All models
provide directional motion sensing.
Direction sensitivity in each zone can be set to up, down, left, or
right. The size of each zone may be adjusted to accommodate
varying applications. Each unit features special circuitry to
minimize the effects of camera vibration, changes in cloud cover,
and extraneous activity such as precipitation and leaf movement.
Four sets of system setup parameters may be stored and
automatically recalled at predetermined times. User defined
password control prevents unauthorized access to setup
parameters.
www.boschsecuritysystems.com
CCTV
Video Signal Equipment | 227
Technical Specifications
Electrical
Environmental
Operating Temperature
0°C to +50°C (32°F to +122°F)
4 Channel Models
LTC 2211/60
LTC 2211/50
Storage Temperature
-40°C to +60°C (-40°F to +140°F)
Rated Voltage
120 VAC, 60 Hz
230 VAC, 50 Hz
Humidity
10% to 80% relative, non condensing
Voltage Range
105 to 130
195.5 to 253
Vibration
3 g swept sine wave, 15 Hz to 2000 Hz
Power at rated Voltage
10 W
10 W
Shock
50 g, 11 ms, 1/2 sine
8 Channel Models
LTC 2212/60
LTC 2212/50
Product Regulatory Compliance
Electromagnetic Compatibility (EMC)
Rated Voltage
120 VAC, 60 Hz
230 VAC, 50 Hz
Voltage Range
105 to 130
195.5 to 253
Power at rated Voltage
10 W
10 W
Detection Analysis
System algorithms are used to pinpoint
Complies with FCC Part 15, ICES-003
and CE regulations
Product Safety:
actual scene motion and help eliminate
Complies with CE regulations, UL, CSA,
EN and IEC Standards
false alarms. On-screen menu
Options
programming.
LTC 9101/00 Rack Kit
Video Inputs
For mounting one or two units in an
EIA 19-inch rack
LTC 2211 Series
Four looping; 8 BNC
LTC 2212 Series
Eight looping; 16 BNC
Range
0.5 Vp-p to 2.0 Vp-p
Controls
Impedance
Automatically switching 75 Ohm
ALM CLR/ESC Key
terminated or high impedance looping
ALARM LED
Height: One standard rack unit
Width: One standard rack unit
Video Outputs
75 Ohm
SETUP/ENTER Key
Video Out
Two; BNC
RUN Key
MON A
Setup, Call-up, or Alarm Call-up
MON B
Sequence, Call-up
Sensitivity
100 levels, selectable per zone, time
NTSC: 40 element(H) by 30 element(V)
programmable
grid
Normally open relay contact closure; one
PAL: 40 element(H) by 28 element(V) grid
Alarm Outputs
MON B Key
Detection Zones
Maximum size is the entire active video
contact closure per camera; one common
contact closure via a 25-pin D-connector.
Ordering Information
Relay contacts are rated at0.5 A at 40 V
Model & Description
AC/DC; resistive load 10 VA maximum
LTC 2211/60
Color coded alarm cable provided
Alarm Setup Input
One setup input, used to change motion
detector setups remotely
Serial Printer Port
9-pin D-Connector
AC Power Cord
3-wire, grounded plug
Cable (Included)
25-pin D-Connector to 9-pin Connector
(break-outs for alarm outputs & serial
printer)
Mechanical
Finish
Charcoal
Dimensions
223 x 362 x 40 mm
(W x D x H)
(8.77 x 14.25 x 1.59 inch)
Weight
2.6 kg (5.7 lb)
www.boschsecuritysystems.com
4-channel digital motion detector, indoor/outdoor, 115 V, 60 Hz
LTC 2211/50
4-channel digital motion detector, indoor/outdoor, 220 V, 50 Hz
LTC 2212/60
8-channel digital motion detector, indoor/outdoor, 115 V, 60 Hz
LTC 2212/50
8-channel digital motion detector, indoor/outdoor, 220 V, 50 Hz
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement