DeWalt | DC987 | Operating instructions | DeWalt DC987 Operating instructions

DeWalt DC987 Operating instructions
Operating
Instructions
UL4000
Ultra-Lok Tool
UL4000 Cordless Ultra-Lok Tool
Table of Contents
Warranty, Safety Guidelines, Contents
Setup Instructions
2
3-4
Settings
5
Parts List
6
Troubleshooting
7
Assembly Instructions
8
Clamp Application
Free-End
Preformed
Maintenance
Blade Change
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
9-10
11
12-13
14
www.BAND-IT-IDEX.com
Page 1 of 14
Document # P07886 Rev. L
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
UL4000
Ultra-Lok Tool
Warranty, Safety
Guidelines, Contents
Warranty:
Refer to website for warranty information: www.band-it-idex.com/warranty.html
NOTE: Any performance data published herein is based on laboratory tests, which cannot duplicate conditions that may
be encountered in field installations. Such conditions may vary results substantially from those shown (such as abuse in
handling and installation, failure to follow recommended handling and installation practices, abnormal environmental
conditions, disregard of operating instructions for BAND-IT tools or non-recommended combinations of BAND-IT
products). BAND-IT cannot be responsible for performance characteristics from such variables.
Safety Guidelines
When applying clamps, care should be taken to make certain that fingers are not in the way of the clamp being
applied. Tensioning the clamp can be stopped immediately by releasing the trigger. Detailed instructions are in
this manual and the operator is advised to read it and become familiar with operating the tool.
IMPORTANT: When clamping a hose end, remember that a tighter clamp keeps the fitting more secure, but
excess tension could damage the hose. Fitting stem must have prominent barbs for proper retention inside the
hose, but must not be sharp to prevent cutting into the hose. Hose, fitting and clamp must be compatible with
each other and the environment used in. If in doubt, consult the hose or fitting manufacturer or call BAND-IT.
Clamping objects other than hose requires similar precautions.
CAUTION: Improperly tightened clamps may result in dangerous hose assemblies, which could cause injuries or
property damage.
CAUTION: Abuse or use of a hose outside the manufacturers recommended conditions may cause it to quickly
deteriorate and become a safety hazard. This could result in serious injury or property damage. Inspect and test
hose assemblies frequently.
Contents
Tension Body
Drill
Additional Battery
Pack
Battery Charger
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
www.BAND-IT-IDEX.com
Page 2 of 14
Document # P07886 Rev. L
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
Setup
Instructions
UL4000
Ultra-Lok Tool
Warning:
Always wear safety glasses when operating this tool. Keep both hands away from clamp being tensioned. Use
common sense, squeezing force of ¾” clamp can reach as high as 2 tons. Never attempt to clamp objects which
can shatter, or otherwise cause bodily harm.
1. Read safety instructions and operator‟s manual for the DeWalt DC987/DW987/DC925 cordless drill. Check to make
sure drill is properly set up for use with Band-It Ultra-Lok tool as follows:
-----Drill spindle has adapter clutch (Band-It #M21790) installed in place of standard drill chuck.
-----Speed gear selector must be on number 1, and drill clutch torque setting as shown on page 5.
2. Charge drill according to the operator‟s manual for the DeWalt cordless drill.
3. To mount drill onto Band-It Ultra-Lok tool: First use the two #10-32 x 3/8” screws supplied with tool to tighten tool
adapter body to the tool. With adapter clamp on tool adapter body, insert drill into back of tool through the adapter
clamp. Turn drill manually to desired position in relation to tool. Press the drill firmly into tool. Actuate drill if necessary
to engage drill safety clutch (M21790) to tension screw. Tighten clamp screw while keeping the drill firmly pressed
against the tool. To remove drill from tool: loosen the clamp screw and pull drill away from the tool.
4. This tool was designed for, and can only be used with BAND-IT ¾” and ½” wide Ultra-Lok clamps. Do not attempt to
use on any other type of clamp as it may damage tool. Only use ½” wide clamps when the optional ½” shear plate
(BAND-IT #M09387) has been installed in the head in place of the ¾” shear plate.
Use only with BAND-IT ¾” and ½” Ultra-Lok Free-End and Preformed Clamps
Tension Block Position
Viewing Slot
(also lubrication syringe access)
Adapter Clamp
M08288
Drill
Clutch
Gear Selector
Drill
M09485 ( DC987,
DC925, or equivalent)
or M07087 (DW987)
Forward
Reverse
Selector
Switch
Tool
Head
Band
Slot
Tool Body
Adapter
M07687
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
Adapter
Clamp
Tension
Screw
www.BAND-IT-IDEX.com
Page 3 of 14
Document # P07886 Rev. L
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
UL4000
Ultra-Lok Tool
Setup
Instructions
NOTE: Alignment is critical for proper tool function.
Tension Screw
Safety Clutch
Note: Some components are not visible in this illustration.
When installing the tool on the drill, be careful to align the end of the Tension Screw with
the slot in the end of the safety clutch, as shown above.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
www.BAND-IT-IDEX.com
Page 4 of 14
Document # P07886 Rev. L
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
UL4000
Ultra-Lok Tool
Settings
Recommended Drill Clutch Torque Settings:
Drill Model
Clamp Size
Single Wrap
Double Wrap
*Preformed
DC987
¾”
½”
11-13
5-9
17-22 11-13
17-22 11-13
DW987
¾”
½”
5-7
4-6
15-19
5-7
15-19
5-7
DC925
¾”
½”
11-15
3-7
19-20 11-15
19-20 11-15
Always Set Speed Selector to “1”
NOTE: These torque settings are suggested settings only, individual tools should be
adjusted for the clamping application.
The tool accompanying this manual was function tested at a clutch setting of __________
and produced a pull-up force of _____________ lbf.
Serial #__________________Tested by:________________ Test date:_______________
*IMPORTANT: Larger sizes of preformed clamps (5" and up) may require a lower setting
to avoid over-stressing the lock and creating potentially unsafe assemblies. Inspect lock per
instructions on page 9-11.
NOTE: When tightening the adapter clamping screw, safety clutch (M21790) must be engaged
with tension screw inside of BAND-IT tool.
Important: Changing speed setting will alter tension output. Speed setting must remain at 1 when
applying tension to the clamp tail. Drill switch must be depressed fully by the operator to attain
correct tension when installing clamps. Tension output may be somewhat different from tool to
tool on the same setting, depending on condition and wear of internal components.
Caution: Improperly tightened clamps may result in dangerous assemblies, which could cause
injuries or property damage.
Use of Alternate Drills
Using correctly sized clamps (diameter)
will, in most cases,
CAUTION
! eliminate the need to pull on clamp
tail more than once. Tension block moves approximately 5”. On occasion, if needed, large size
clamps can be installed by taking several bites (clamp tail feeds out through back of tool).
The UL4000Position
tool is designed
work mounted
the DeWalt
DC987/DW987/DC925
cordless
drill.
of any other
of tensiontoblock,
containingtogripper,
can be
monitored through viewing
holes
justUse
under
drills in place
of the
DeWaltTool
may
result in
unsatisfactory
performance,
to the
operator
cut-off
handle.
features
built-in,
disengaging
mechanismhazards
to prevent
tension
screwand/or
from the tool, or
unsafe clamps.
Use up.
of alternate
drills
must
be feature
approved
writing
by the
Director and/or
of Engineering
at BAND-IT-IDEX,
jamming
Excessive
use
of this
willinwear
clutch
mechanism
tension screw
out
Inc. Disregard
of
this
caution
voids
the
warranty
of
the
tool
and
releases
BAND-IT
of
any
and
all
liabilities arising
prematurely.
from such misuses.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
www.BAND-IT-IDEX.com
Page 5 of 14
Document # P07886 Rev. L
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
UL4000
Ultra-Lok Tool
Parts List
Notes:
Apply Item 31 (Grease) to:
Item 4 (Cut off Cam)
Item 3 (Cutter Knife) at contact point with item 1 (Tool Head)
Item 26 (Spring) before installation
Apply Item 32 (Grease) to:
Item 7 (Tension Screw) threads and at grooved end
Item 2 (Cutter Blade) counter-bore only, after item 14 (Bearing Tip) has been installed.
Tighten the following:
Item 23 (#10-32 Screws)
to 60 – 70 in-lbs.
Item 22 (1/4-28 Screws)
to 90 – 110 in-lbs.
Adjust Item 24 (Plunger) for
positive detent action when
item 6 (Handle) is actuated.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
Item
1
2
3
4
5
Part Number
M00587
M09787
M08687
M08987
M09087
Quantity
1
1
1
1
1
6
UL1219
1
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
M00987
M08887
M01787
M09187
M02387
M00287
M01388
M05387
M06587
M02287
M04387
M07387
M07487
M07587
M05787
J67287
M06187
M02487
A33887
A53587
M01487
M08187
M08087
M07987
I16387
C23187
M09887
M09387
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
4
4
2
1
2
1
4
4
2
.07
.03
1
1
www.BAND-IT-IDEX.com
Page 6 of 14
Description
Tool Head, Fin. UL
Cutter Blade, UL
Cutter Knife, UL
Cam, Cut-off, UL
Tension Block, Mach., UL
Handle Assembly:
Includes Handle, Handle Grip, and Pins
Tension Screw, Fin.
Gripper, UL
Plate, Back, Cast/Fin.
Gripper Guide, UL
Plate, Release, cast/fin.
Roller, Cut-off, Fin.
Pin, .187 Dia X 1.50 Long, Fin.
Bearing Tip, Fin.
Ball, ¼” Diameter
Tip, Load Bearing, Fin.
Tripper Bracket, Cast/Fin.
Body, Left, Finished, UL
Body, Right, Finished, UL
Wear Plate, Fin.
Screw, Socket Head Cap, ¼ X 1”
Screw, Socket Head Cap, ¼ X ½”
Screw, Socket Head Cap, #10-32 X 3/8”
Screw, Spring Plunger, ¼-20
Spring, Compression, .180 X .813 Long
Spring, Compression, .300 X 1.00 Long
Pin, Dowel, ¼ Dia X 1.50 Long
Washer, .128 ID X .238 OD
Rivet, Blind, .125 X .328 Long
Threaded Insert, #10-32
Lubricant, Super Lube w/ Teflon (cc)
Lubricant, Black Moly, Hi-Temp (cc)
Shear Plate, ¾”, UL
Shear Plate, UL, ½” (Optional)
Document # P07886 Rev. L
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
Troubleshooting
UL4000
Ultra-Lok Tool
6
2 Places
30
18
28
4
Tension Block
ASSY
4 Places
6
23
4 Places
20
19
29
4 Places
2 Places
Head Unit
22
4 Places
See page 6 for parts list
Trouble-Shooting
1. Lock slips down in buckle: Tighten blade mounting screws. If lock on clamp is still not adequate,
reduce tension on tool by setting torque setting on the drill clutch to a lower number.
2. Safety clutch between drill and tool releases prematurely: Make sure tool is fully seated on drill.
(see page 4) If problem still remains, contact BAND-IT technical support.
Note: To prevent over-travel safety clutch wear, do not over-use safety clutch. When tensioning clamp,
let drill switch go as tension block nears its end of travel. Reverse drill and send tension block all the way
forward for a second pull on the band.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
www.BAND-IT-IDEX.com
Page 7 of 14
Document # P07886 Rev. L
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
UL4000
Ultra-Lok Tool
Assembly
Instructions
9
Tension Gripper Assembly
32
7 32
Brush lubricant evenly
on threads
5
16
17
26 31
2 Places
Tool Head Assembly
8
4 31
Component
under spring
load when
assembled
24
2 Places
Lubricate
both sides
10
27
21
2 Places
13
11
25
Component
under spring
load when
assembled
31
* M09387 (Optional)
½” Shear Plate Insert
can be substituted for
item # 33
13
12
1
3
33
15 32
14 32
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
See page 6 for parts list
2
www.BAND-IT-IDEX.com
Page 8 of 14
Document # P07886 Rev. L
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
UL4000
Ultra-Lok Tool
Clamp Application
Free-End Clamps
Warning: Always wear safety glasses when operating tool.
1. Break off an Ultra-Lok Free-End
tie from the roll. Slide the buckle
onto band with indented arrows
pointing in same direction and
same side up. Slide buckle all
the way onto band until it comes
to a stop between the two buckle
dimples at opposite end of tie.
2. Wrap tie around object to be clamped.
Insert the tie through buckle once for
single-wrap or twice for double-wrap.
Double-wrapped clamps have more
than 3 times the loop-tensile strength.
DO NOT
FEATHER
the drill’s
TRIGGER
when
tensioning
a clamp.
USE FULL
SPEED OF
TOOL
4. Position the tie on the
object you are clamping.
Pull the wrapped tie
hand-tight. Slightly bend
the tail up to keep the
clamp in place
5. Actuate drill until tension block is all the
way forward against the tool body. Set
drill to clock-wise rotation. With cut-off
handle down as shown, insert clamp tail
into tool head slot. Actuate drill until drill‟s
built-in clutch disengages. If tension
block comes near its end of travel,
release actuator switch and reverse drill
to pull more on clamp tail. Excessive use
of disengaging clutch indicated by a loud
ratcheting sound leads to premature
wear of tension screw.
Correct position of tool
while tensioning
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
www.BAND-IT-IDEX.com
Page 9 of 14
3. If desired, you may preform a clamp in the same
fashion as step 2, or use a
preformed clamp in place
of a Free-End
Push all
the way
forward
to a solid
stop
6. Do not force tool against clamp; it may
result in a folded clamp tail.
7. Pull the cut-off handle forward to cut
tail off and form a lock, then return
handle to the down position. Reverse
drill and feed clamp tail out of tool.
8. Tap down buckle shroud to complete
clamp. Tool is ready for next clamp.
Incorrect position of tool
while tensioning
Document # P07886 Rev. L
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
UL4000
Ultra-Lok Tool
Clamp Application
Free-End Clamps
Inspect buckle on completed clamp and tap down buckle shroud.
Section View
Good Clamp
FRONT VIEW
Completed Free-End Clamp
(Visually inspect lock)
Lock sheared in center
and formed inside
shroud
Buckle Shroud
Bad Clamp
Lock has slipped back
under sheared buckle
surface
Shear Surface
Important: Visually inspect lock formed in band as shown. If lock has slipped under the sheared surface of the
buckle, remove clamp and install a new one at reduced tension by lowering the drill clutch torque setting.
SIDE VIEW
Completed Free-End
Clamp
Tap down buckle shroud to
complete clamp
Completed clamp
should appear as
shown.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
www.BAND-IT-IDEX.com
Page 10 of 14
Document # P07886 Rev. L
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
UL4000
Ultra-Lok Tool
Clamp Application
Preformed Clamps
Place clamp in desired position on object to be clamped.
Follow steps 5 and 6 on page 9.
Inspect buckle on completed clamp and tap down buckle shroud as shown below.
Section View
Good Clamp
Lock sheared in center and
formed inside shroud
Front View
Completed Clamp
(Visually inspect lock)
Buckle Shroud
Shear Surface
Bad Clamp
Lock has slipped back
under sheared buckle
surface
Important: Visually inspect lock formed in band as shown. If lock has slipped under the sheared surface of the
buckle, remove clamp and install a new one at reduced tension by lowering the drill clutch torque setting.
Side View
Completed Clamp
Tap down buckle
shroud to complete
clamp
When applying clamps on soft, thick-walled hose, tension clamp then wait a full 30
seconds. Clamps may be retensioned by squeezing the actuator switch on the power
unit a second time prior to forming the lock and cutting the excess clamp tail. This allows
hose to “settle” under the band of the clamp. This hose material attribute is called Cold
Flow. Finally, complete clamp by tapping down the buckle shroud as described above.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
www.BAND-IT-IDEX.com
Page 11 of 14
Document # P07886 Rev. L
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
UL4000
Ultra-Lok Tool
Maintenance
1. Approximately every 500 clamps, lubricate tension screw with
molybdenum disulfide lubricant, or equivalent.
Make sure tension block is all the way forward against the tool head. Remove
cap from syringe and insert tip of syringe into slot on top of tool body. Press
the tip against the tension screw just behind the tension block and squeeze
out approximately ½” long bead of lubricant. Remove syringe, and actuate
tool without a clamp a couple of times to spread lubricant evenly on tension
screw.
Lubricating
Syringe. Reorder
#C23199
To order more lubricant, specify BAND-IT #C23199
2. Every 500-1000 clamps, depending on tension setting, inspect
and repack front bearing with same lubricant. Turn load bearing tip and
small bearing tip over for a new bearing surface.
Bearing Detail
Small Bearing Tip
Item 14
Access Hole to push
out components (use
paper clip)
¼” Ball
Item 15
Blade
Item 2
Tool
Head
Item 1
Tool
Body
Load Bearing Tip
Item 16
Blade Cavity,
must be packed
with lubricant
Tension
Screw
Item 7
Blade Mounting
Screws
Item 22
3. To gain access to bearing components: remove blade mounting
screws (2 places) and slide blade free. Paper clip may be used to push
bearing components out of blade. Wipe lubricant from components. If ball or
bearing tips appears heavily worn, replace with new one. Note: ¼” ball is
made from hard tungsten carbide material, do not replace with regular ball
bearing. (Smooth indention from ball in the bearing tips is normal).
To re-assemble bearing components: wipe blade cavity clean. Push small
bearing tip into blade cavity. Apply lubricant to ball and push into blade cavity
and fill remaining space with lubricant. Push load bearing tip firmly into blade
cavity, some lubricant will be squeezed out. Re-attach blade to tool head,
making sure that load bearing tip extends into tension screw. While turning
blade mounting screws into blade, push on blade rearwards. Tighten screws
to approximately 120 in-lbs.
4. When replacing worn blade follow instructions above to properly
re-assemble bearing components.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
www.BAND-IT-IDEX.com
Page 12 of 14
Document # P07886 Rev. L
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
UL4000
Ultra-Lok Tool
Maintenance
5. To replace gripper: Make sure tension block is all the way forward against the tool head.
Remove drill. Remove tool adapter body. Remove one side of the tool body or the other, not both.
Slide gripper out sideways and replace with a new one. Re-attach tool body side. Caution: Do
not push or move tension block while gripper is out of tool.
Tool Head
Item 1
This tip must align with
the safety clutch
(M21790) on the DeWalt
drill. See page 4.
Move tension
block all the way
forward against
the tool head.
Gripper
Item 8
Tension
Screw
Item 7
6. To replace tension screw: Move tension block all the way back (away from tool head) using drill
in tensioning mode (clock-wise). Remove Ultra-Lok tool from drill. Remove the tool adapter body from
the Ultra-Lok tool. Remove blade and load bearing tip from tensioning screw (see bearing detail).
Remove one side of the tool body or the other, not both. Grasp the smooth barrel on tension screw and
pull all the way forward until tension block is against the tool head. If tension screw is stuck, use a
punch and tap the center of the screw from the back end of the tool. Turn tension screw out of tension
block. Lubricate new tension screw with Molybdenum Disulfide lubricant, or equivalent. Install new
tension screw in reverse order, making sure that back end of tension screw extends well beyond the
back end of the tension block. Push the assembly all the way back and extend the round portion of the
tension screw through holes on the tripper bracket and back guide plate. Reinstall tool body side.
Reinstall blade and tighten the blade mounting screws approximately 120 in-lbs. Reattach tool adapter
body to Ultra-Lok tool. Reattach tool to drill and drive tension block all the way forward.
Note: Drills needing repair must be forwarded to an authorized „DeWalt‟ repair center in your area. Be
sure to remove BAND-IT safety clutch (M21790) from drill.
DeWalt Drill is covered solely by the DeWalt warranty as described in the DeWalt literature. BAND-IT
does not extend any warranty of any kind to the drill.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
www.BAND-IT-IDEX.com
Page 13 of 14
Document # P07886 Rev. L
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
UL4000
Ultra-Lok Tool
Optional ½” Tool
Blade Change
To change out the UL4000 tool to the 1/2” version, the following steps should be followed.
*NOTE: Do not attempt to use 1/2” clamps with 3/4” head. (Adapter change-out: 3-5 minutes)
1. Prior to separation from power drill, back off tension block assembly ½” from head unit. See page 7.
2. Detach tension body from the battery-powered drill by loosening the single tensioning bolt on the aluminum collar and
separating the two sections.
3. Remove the blade from head by removing two cap screws (M05787) from the top of the head. It is not necessary to
remove entire head from tool in order to remove blade. (Figure 1) Remove the ¾” adapter plate from the blade.
4. Align the ½” adapter plate (M09387) with the blade (M09787) so that the guide is facing up. Incorrect placement will
not allow bands to be inserted into the tool. (Figure 1)
Note: To convert tool back to ¾”, replace ½” insert with ¾” insert (M09887) and follow same instructions.
Be sure to retain unused shear plate for later use.
5. Attach the blade and ½” adapter plate onto head using the two previously removed cap screws. These cap screws
must be tight to assure proper cut-off of clamp tails.
6. Re-attach drill to tension body making sure the drill and tension body are properly aligned, and tighten the single
adapter cap screw located on the aluminum collar.
7. This tool is not designed to work with traditional band and buckle designs. BAND-IT Ultra-Lok clamps must be
used.
Blade Cap Screw
(M05787) Qty. 2
¼” Ball (M06587)
Bearing Tip (M05387)
Blade (M09787)
Optional ½” Insert
(M09387)
Orient as shown
Blade (M09787)
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
Figure 2
Figure 1
www.BAND-IT-IDEX.com
Page 14 of 14
Document # P07886 Rev. L
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising