VTech | 900i | User`s guide | VTech 900i User`s guide

VTech 900i User`s guide
2-9917/2-9918
900MHz Hands-free
Cordless Telephone
User’s Guide
We bring good things to life.
FCC REGISTRATION INFORMATION
Your GE telephone equipment is registered with the Federal Communications Commission and is in compliance with
parts 15 and 68, FCC Rules and Regulations.
1 Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the FCC Registration number and
Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this information to your
telephone company.
The REN is useful in determining the number of devices you may connect to your telephone line and still have all
of these devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all
devices connected to one line should not exceed 5. To be certain of the number of devices you may connect to your
line as determined by the REN, you should contact your local telephone company.
Notes
• This equipment may not be used on coin service provided by the telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone equipment if
you are on a party line. Check with your local telephone company.
• Notice must be given to the telephone company upon permanent disconnection of your telephone from your
line.
2 Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone network, the telephone
company shall, where practicable, notify you that temporary discontinuance of service may be required. Where
prior notice is not practicable and the circumstances warrant such action, the telephone company may temporarily
discontinue service immediately. In case of such temporary discontinuance, the telephone company must: (1)
promptly notify you of such temporary discontinuance; (2) afford you the opportunity to correct the situation; and
(3) inform you of your right to bring a complaint to the Commission pursuant to procedures set forth in Subpart E
of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment, operations of procedures
where such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations.
If these changes are expected to affect the use or performance of your telephone equipment, the telephone
company must give you adequate notice, in writing, to allow you to maintain uninterrupted service.
INTERFERENCE INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference; and (2) This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the
interference).
• Reorient or relocate and increase the separation between the telecommunications equipment and receiving
antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving
antenna is connected.
• Consult the dealer or an experienced radio/TV technician for help.
If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television
technician for additional suggestions. Also, the Federal Communications Commission has prepared a helpful
booklet, “How To Identify and Resolve Radio/TV Interference Problems.” This booklet is available from the U.S.
Government Printing Office, Washington, D.C. 20402. Please specify stock number 004-000-00345-4 when
ordering copies.
HEARING AID COMPATIBILITY
This telephone system meets FCC standards for Hearing Aid Compatiblility.
2
FCC NUMBER IS LOCATED ON THE CABINET BOTTOM
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
TABLE OF CONTENTS
INTRODUCTION ............................... 4
The Memory Feature ................. 10
Digital security system ................ 4
Modular jack requirements ......... 4
Storing a Number in Memory . 10
GETTING STARTED .......................... 5
Changing a Stored Number ..... 11
Storing a Pause in Memory ..... 11
Charging the Batteries ................ 5
Installation & Setup ..................... 6
USING YOUR HANDS-FREE PHONE .... 7
Placing or Receiving Calls ........... 7
In Use Indicators .......................... 7
Base Unit ..................................... 7
Handset ........................................ 7
Buttons and Features .................. 8
Volume ......................................... 8
Mute ............................................. 8
Channel Button ........................... 8
Memory Button ........................... 8
Pause ........................................... 8
Dialing a Stored Number ......... 12
Chain Dialing from Memory .... 12
BATTERY INFORMATION .................. 12
Battery Safety Precautions ....... 13
Changing The Battery ............... 13
TROUBLESHOOTING GUIDE ............. 14
SERVICE ...................................... 15
GENERAL PRODUCT CARE .............. 16
Causes of Poor Reception ......... 16
INDEX ......................................... 17
LIMITED WARRANTY ...................... 18
ACCESSORY ORDER FORM ............. 19
Ringer Adjust .............................. 8
Flash Button ................................ 9
Redial Button ............................... 9
Temporary Tone Feature ............ 9
Page/Find ................................... 10
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO PREVENT FIRE
OR ELECTRICAL SHOCK HAZARD,
DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
THE LIGHTNING
FLASH AND ARROWHEAD WITHIN THE
TRIANGLE IS A
WA R N I N G S I G N
ALERTING YOU OF
"DANGEROUS
VOLTAGE" INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER
(OR BACK). NO USERS E RV I C E A B L E PA R T S I N SIDE. REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING
SIGN
ALERTING YOU OF
I M P O R T A N T
INSTRUCTIONS
A C C O M PA N Y I N G
T H E P R O D U C T.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
3
INTRODUCTION
Your GE 900 MHz Cordless Telephone is designed to give you flexibility in
use and high quality performance. To get the most from your new cordless
telephone, we suggest that you take a few minutes right now to read
through this instruction manual.
The following is important information regarding the use of your cordless
phone:
• Digital Security System
When you place the Handset in the base, the unit verifies it’s security code
which prevents false ringing from other cordless telephones. After a
power outage or battery replacement, you should place the Handset in the
base for about 20 seconds to reset the code.
• IMPORTANT: You Should Own a Non-Cordless Phone Too
Because cordless phones operate on electricity, you should have at least
one phone in your home that is not cordless, in case the power in your
home goes out.
• Installation Note
Some cordless telephones operate at frequencies that may cause
interference to nearby TVs and VCRs. To minimize or prevent such
interference, the base of the cordless telephone should not be placed near
or on top of a TV or VCR. If such interference continues, move the cordless
telephone farther away from the TV or VCR.
Modular Jack Requirements
You need an RJ11 type modular jack, which
is the most common type of phone jack
and might look like the one pictured here. If
you don’t have a modular jack, call your
local phone company to find out how to get
one installed.
4
GETTING STARTED
Make sure your package includes the items shown here.
AC power adapter
IN USE/LOW BATT
Battery
PHONE
VOL
UME
UME
VOL
MUTE
7
Base
MNO
8
WXYZ
JKL
PQRS
PAGE/FIND
DEF
ABC
4
GHI
CHARGE
IN/USE
2
5
1
*
TONE
TUV
OPER
0
3
6
9
#
CHANNEL
MEMORY
PAUSE
RINGER
ADJUST
FLASH
REDIAL
Handset/Headphone
Headset hook
Telephone line cord
CHARGING THE BATTERIES
1. Plug the power supply cord into the
POWER 12V DC jack on the base and into
an AC outlet.
2. Place Handset or just the battery itself
into the base to charge for 12 hours. The
CHARGE/IN USE light (on the base)
comes on to indicate that the battery is
charging.
TONE
TEL. LINE
+
DC 12V 500mA
PULSE
IN USE/LOW BATT
PHONE
In Use
Indicator
VOL
UM
E
VO
LUM
E
MUTE
1
4
GHI
PQRS
7
*
ABC
3
2
DEF
5
MNO
JKL
TUV
8
OPER
CHANNEL
MEMORY
9
#
0
TONE
6
WXYZ
PAUSE
CHARGE
IN/USE
PAGE/FIND
If you don’t charge the Handset
battery properly (for 12 hours) when
you first set up the phone,
performance of the battery will be
compromised.
CHARGE
IN/USE
PAGE/FIND
5
INSTALLATION & SETUP
1. Make sure that the power supply cord is plugged into the POWER 12V
DC jack on the base and into an AC outlet.
2. Plug the telephone line cord into the PHONE LINE jack on the base and
into a modular jack.
3. Set the TONE/PULSE switch to TONE for touch-tone service, or PULSE
for pulse (rotary) service. If you don’t know which type of service you
have, check with the phone company.
4. Slide the base RINGER switch to ON if you want the unit to ring for
incoming calls. (The RINGER switch is located on the same side of the
base as the antenna.)
Note: For convenience,
attach the headset hook
to the slots at the back
of the base. You can rest
the headset here when
you are not using it.
5. Raise the base antenna.
5
RINGER
OFF
1
ON
4
TONE PULSE
PHONE LINE
POWER DC 12V
2
3
NOTE: Use only the Thomson 5-2430 (black)/5-2431 (white) power supply
that came with this unit. Using other adapters may damage the unit.
6
USING YOUR HANDS-FREE PHONE
PLACING OR RECEIVING CALLS
Whether you are placing or receiving a call,
you just need to know the following
basics:
IN USE/LOW BATT
PHONE
VOLUM
VOLUM
E
• You need to use the headset to listen
and talk.
E
MUTE
1
ABC
4
JKL
7
TUV
GHI
PQRS
DEF
5
MNO
8
WXYZ
0
*
TONE
• Press the PHONE button on the Handset
to get a dial tone, to answer an incoming
Call, or to hang up.
2
OPER
3
6
9
#
CHANNEL
MEMORY
PAUSE
RINGER
ADJUST
FLASH
REDIAL
• Placing the Handset in base will also
hang up.
• You cannot place or receive a call while
the handset is in the base.
In Use Indicators
IN USE INDICATORS
BASE UNIT
The IN USE indicator on the base unit
comes on whenever the phone is in use, or
when the handset is charging in the cradle.
IN USE/LOW BATT
PHONE
VOLU
VO
MUTE
1
GHI
4
7
PQRS
HANDSET
LUME
ME
*
ABC
3
2
DEF
6
5
MNO
JKL
TUV
8
9
WXYZ
#
0
TONE
OPER
CHANNEL
MEMORY
PAUSE
CHARGE
IN/USE
PAGE/FIND
The IN USE indicator on the handset comes
on whenever the phone is in use, and
blinks slowly when the battery power gets
low.
7
BUTTONS AND FEATURES
VOLUME
AND
Use the Volume buttons to increase or
decrease the headset volume.
MUTE
The MUTE button is used to interrupt a
phone conversation to talk privately with
someone else in the room.
Mute
Volume
IN USE/LOW BATT
1. Press MUTE to activate mute feature.
PHONE
VO
ME
LUM
VOLU
E
2. Press MUTE again to turn it off.
MUTE
CHANNEL BUTTON
If you ever experience any interference
or don’t have clear voice quality, press
the CHANNEL button on the Handset to
advance to another channel.
PAUSE
Use the PAUSE button to place a pause
in the dialing sequence when storing a
number in memory (see “Memory
Feature” for more information).
RINGER ADJUST
This feature allows you to control the
ringer volume (high, medium, low) for
the Handset. Press the RINGER ADJUST
button until you reach a comfortable
ringer level.
8
MNO
8
WXYZ
JKL
7
TUV
*
TONE
OPER
0
3
6
9
#
CHANNEL
MEMORY
PAUSE
RINGER
ADJUST
FLASH
REDIAL
MEMORY BUTTON
Enables you to save phone numbers in
memory and to quickly dial them later.
DEF
ABC
4
PQRS
Channel
button
2
5
1
GHI
Ringer Adjust
Pause
button
Memory
button
FLASH BUTTON
Use the FLASH button to activate custom
calling services such as call waiting or call
transfer, which are available through your
local phone company.
IN USE/LOW BATT
PHONE
VO
REDIAL BUTTON
VOLU
E
MUTE
The REDIAL button allows you to easily
redial the last number you called. When
you get a dial tone, press REDIAL.
DEF
MNO
8
WXYZ
ABC
4
JKL
7
TUV
PQRS
*
TEMPORARY TONE FEATURE
2
5
1
GHI
TONE
This feature enables pulse (rotary) service
phone users to access touch-tone services
offered by banks, credit card companies,
etc., by pressing the TONE button to
temporarily make the phone touch-tone
compatible. To get information about your
bank account, for example, you would:
ME
LUM
OPER
0
3
6
9
#
CHANNEL
MEMORY
PAUSE
RINGER
ADJUST
FLASH
REDIAL
Tone button
Flash
button
Redial
button
1. Press the PHONE button.
2. Call the bank’s information line.
3. Press the TONE button after your call is
answered.
4. Follow the voice instructions to
complete your transaction.
5. Hang up when finished. The phone
returns to pulse (rotary) service.
TIP: If you press the
PHONE button to activate
custom calling services such
as call waiting, you’ll hang
up the phone. Press FLASH
instead.
9
PAGE/FIND
Use the PAGE/FIND button to locate
a missing handset, or to page the
person using it.
• Press and release the PAGE/FIND
button to page the handset with
three short tone bursts.
• Press and hold the PAGE/FIND
button to emit a continuous tone
from the handset. When you
locate it, press the PHONE button
to STOP the tone.
THE MEMORY FEATURE
CHARGE
IN/USE
PAGE/FIND
Page/Find button
Store up to 10 numbers in memory
for quick dialing.
STORING A NUMBER IN MEMORY
IN USE/LOW BATT
PHONE
1. Press the MEMORY button.
VO
ME
LUM
VOLU
E
MUTE
2. Dial the number to be stored (up
to 16 digits).
3. Press MEMORY.
DEF
MNO
8
WXYZ
ABC
4
JKL
7
TUV
PQRS
*
TONE
4. Press any number key (0-9) to
store the phone number in that
memory location.
2
5
1
GHI
OPER
0
3
6
9
#
CHANNEL
MEMORY
PAUSE
RINGER
ADJUST
FLASH
REDIAL
Available Memory Numbers
NOTE: A memory index card is located under the base unit. You
may log your numbers stored in memory here. Pull out the card
whenever needed for reference.
10
STORING A PAUSE IN MEMORY
Use the PAUSE button to insert a
pause when a delay is needed in
the dialing sequence (for example,
when you must dial a 9 to get an
outside line or when you must
enter codes to access your bank’s
information line).
TIP: If you need a longer pause,
press PAUSE several times.
If you need to dial 9 to get an
outside line and want to store a
number in memory without having
to dial 9 each time, you would:
IN USE/LOW BATT
1. Press MEMORY.
PHONE
VO
ME
LUM
VOLU
E
2. Press 9.
MUTE
DEF
MNO
8
WXYZ
ABC
4
JKL
7
TUV
GHI
4. Dial the phone number you want
to store in memory.
2
5
1
3. Press PAUSE.
PQRS
*
TONE
OPER
0
3
6
9
#
CHANNEL
MEMORY
PAUSE
RINGER
ADJUST
FLASH
REDIAL
5. Press MEMORY.
6. Press any number key (0-9) to
store the phone number in that
memory location.
Pause button
Memory button
CHANGING A STORED NUMBER
Use the same procedure to change
a stored number as you do to store
a number— you’re just replacing
the phone number in that memory
location.
11
DIALING A STORED NUMBER
1. Press the PHONE button to get a dial
tone.
IN USE/LOW BATT
PHONE
VO
Available Memory
Numbers
ME
LUM
VOLU
E
MUTE
2. Press MEMORY and then press the
number for that memory location.
1
ABC
4
JKL
7
TUV
GHI
PQRS
*
TONE
CHANNEL
2
DEF
5
MNO
8
WXYZ
OPER
0
MEMORY
3
6
9
#
PAUSE
CHAIN DIALING FROM MEMORY
Use this feature to make calls which require a sequence of numbers, for
instance if you use a calling card for a frequently called long distance
number. Basically, you dial each part of the sequence from memory. The
following example shows how you can use chain dialing to make a call
through a long distance service:
The Number For
Memory Location
Long distance access number
Authorization code
Frequently called long distance number
7
8
9
1. Press the PHONE button to get a dial tone.
2. Press the MEMORY button and then press 7.
3. When you hear the access tone, press MEMORY and then press 8.
4. At the next access tone, press MEMORY and then 9.
BATTERY INFORMATION
BATTERY SAFETY PRECAUTIONS
• Don’t disassemble, mutilate, puncture, wet, or dispose of battery in fire.
Like other batteries of this type, if it is burned or punctured, it could
release toxic materials which can cause injury.
• Keep batteries out of the reach of children.
12
Release tab
CHANGING THE BATTERY
Follow these steps to change the battery:
1. Press the release tab on back of the
handset.
2. Grasp the battery cartridge, pulling down
and away from the phone.
3. Place the catridge in the recharge cradle.
4. Insert the new battery cartridge.
5. Place the handset in the base to
charge. If you don’t charge the
handset battery properly (for 12
hours) when you first set up the
phone and/or when you install a new
battery pack, the battery’s long-term
performance will be compromised.
Note: You can charge the new battery prior
to installing it by placing the battery in the
back of the base unit.
CHARGE
IN/USE
PAGE/FIND
Replacement battery: (white) 5-2432
(black) 5-2433
RBR
C
RC
RB
NOTE: The RBRC seal on the battery used in your Thomson
Consumer Electronics product indicates that we are participating in
a program to collect and recycle Nickel Cadmium batteries
throughout the United States. Please call 1-800-8-BATTERY for
information or contact your local recycling center.
Ni-Cd
13
TROUBLESHOOTING GUIDE
In case of difficulty, please check the following Troubleshooting Guide
before seeking service.
Problem
Solution
No dial tone
• Check installation:
— Is the base power cord connected to a working outlet?
— Is the telephone line cord connected to the base unit and
the wall jack?
• Disconnect the base from the wall jack and connect another
phone to the same jack. If there is no dial tone in the second
phone, the problem might be your wiring or local service.
• Is the Handset out of the base unit’s range? Move closer to
the base unit.
• Make sure the battery is properly charged (12 hours).
• Is the battery pack installed correctly?
• If the phone still does not work, disconnect the power cord
and remove the battery pack. Then reconnect the power cord
and reinstall the battery pack. Place Handset in the base for
10 seconds to allow it to reinitialize.
Dial tone is OK, but
can’t dial out
• Make sure the TONE/PULSE switch on the base is set
correctly.
Handset does not ring
• You may have too many extension phones on your line. Try
unplugging some phones.
• See solutions for “No dial tone.”
Cannot hear phone
conversation
• Adjust the volume control on Handset .
You experience static,
noise, or fading in
and out
•
•
•
•
•
Range is shorter
than normal
• Press CHANNEL button during the conversation to select a
new channel.
• Position the base antenna upward.
14
Change channels.
Is Handset out of range? Move closer to the base.
Does the base need to be relocated?
Charge Handset battery.
Make sure base is not plugged into an outlet with another
household appliance.
Problem
Solution
Battery will not hold a
charge or is fully charged
and the BAT LOW lights
• Be sure you are sufficiently charging the battery. When the
battery has been charged for 12 hours, you can expect
approximately 4 hours of talk time.
• Check to be sure battery contacts on both the Handset and
the base are making contact and are clean; free of dirt or lint.
• When the Handset is placed in the base, check that the base
CHARGE/IN USE light is on.
BAT LOW light blinks
• Place Handset in base for 10 seconds to reset the phone. If
that doesn’t work, charge battery for 12 hours.
Memory Dialing
doesn’t work
• Did you program the memory location keys correctly?
• Did you follow proper dialing sequence?
• Make sure TONE/PULSE switch is correctly set.
SERVICE
The FCC requires this product to be serviced only by the manufacturer or its
authorized service agents. In accordance with FCC requirements, changes or
modifications not expressly approved by Thomson Consumer Electronics could
void the user’s authority to operate this product. For instructions on how to obtain
service, refer to the warranty included in this Guide.
Attach your sales receipt to the booklet for future reference or jot down the date
this product was purchased or received as a gift. This information will be valuable
if service should be required during the warranty period.
Purchase date ________________
Name of store ___________________________
15
GENERAL PRODUCT CARE
To keep your telephone working and looking good, follow
these guidelines:
• Avoid putting the phone near heating appliances and devices that
generate electrical noise (for example, motors or fluorescent lamps).
• DO NOT expose to direct sunlight or moisture.
• Avoid dropping the Handset, as well as other rough treatment to
the phone.
• Clean the phone with a soft cloth.
• Never use a strong cleaning agent or abrasive powder because this will
damage the finish.
• Retain the original packaging in case you need to ship the phone at a
later date.
• Periodically clean the charge contacts on the Handset and base with a
eraser.
CAUSES OF POOR RECEPTION
• Aluminum siding.
• Foil backing on insulation.
• Heating ducts and other metal construction can shield radio signals.
• You’re too close to appliances such as microwaves, stoves,
computers, etc.
• Atmospheric conditions, such as strong storms.
• Base is installed in the basement or lower floor of the house.
• Base is plugged into an AC outlet with other electronic devices.
• Baby monitor is using the same frequency.
• Handset battery is low.
• You are out of range of the base.
16
INDEX
A
P
Accessory order form 19
PAGE/FIND button 10
Pause button 8
Placing a call 7
Poor reception 16
Product care 16
B
Battery safety 12
C
Chain dialing 12
Changing a stored number 11
CHANNEL button 8
CHARGE/IN USE light 5
Charging the battery 5
Cleaning the phone 16
D
Digital security system 4
F
FLASH button 9
R
Redial button 9
Ringer adjust 8
S
Service 15
Storing a number in memory 10
T
Temporary tone 9
TONE button 9
Troubleshooting guide 14
I
In Use indicators 7
Installation & setup 6
Interference 4
M
MEMORY button 8, 10, 12
Memory feature 10
Mute button 8
17
LIMITED WARRANTY
What your warranty covers:
• Any defect in materials or workmanship.
For how long after your purchase:
• One year.
(The warranty period for rental units begins with the first rental or 45 days from date of shipment to
the rental firm, whichever comes first.)
What we will do:
• Provide you with a new or, at our option, a refurbished unit.
• The exchange unit is under warranty for the remainder of the original product’s warranty period.
How to make a warranty claim:
• Properly pack your unit. Include any cables, etc., which were originally provided with the product.
We recommend using the original carton and packing materials.
• Include in the package evidence of purchase date such as the bill of sale. Also print your name and
address and a description of the defect. Send standard UPS or its equivalent to:
Thomson Consumer Electronics, Inc.
Product Exchange Center
11721 B Alameda Ave.
Socorro, Texas 79927
• Pay any charges billed to you by the Exchange Center for service not covered by the warranty.
• Insure your shipment in case of loss or damage. Thomson accepts no liability in case of damage or
loss.
• A new or refurbished unit will be shipped to you prepaid freight.
What your warranty does not cover:
• Customer instruction. (Your Owner’s Manual provides information regarding operating instructions
and user controls. For additional information, ask your dealer.)
• Installation and set-up service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modified or incorporated into other products.
• Products purchased or serviced outside the USA.
• Acts of God, such as but not limited to lightning damage.
Product Registration:
• Please complete and mail the Product Registration Card packed with your unit. It will make it easier
to contact you should it ever be necessary. The return of the card is not required for warranty
coverage.
How state law relates to this warranty:
• This warranty gives you specific legal rights, and you may have other rights which vary from state
to state.
If you purchased your product outside the USA:
• This warranty does not apply. Contact your dealer for warranty information.
18
19
5-2431
5-2430
5-2432
5-2433
PRICE*
City ________________________State________ ZIP_________________
Address_____________________________________ Apt.____________
Name________________________________________________________
To:
This is your return label. Please print clearly.
Ronks, PA 17573-8419
P.O. Box 8419
Mail Order Department
Consumer Electronics
Mail order form and money order or check (in U.S. currency)
made payable to Thomson Consumer Electronics, Inc. to:
Total Amount Enclosed.................................$_______________
Shipping, Handling, and Insurance............. $_______________
$5.00
All accessories are subject to availability. Where applicable, we will ship a
superseding model.
Use VISA or MasterCard preferably. Money order or check must be in U.S. currency
only. No COD or Cash.
Sales Tax........................................................$_______________
We are required by law to collect the appropriate sales tax for
each individual state, county, and locality to which the
merchandise is being sent.
Please make sure that this form has been filled out completely.
Authorized Signature
____________________________________________________________________
My card expires:
Copy the number above your
name on the MasterCard
Copy your complete account number from your MasterCard.
My card expires:
Copy your complete account number from your VISA card.
*Prices are subject to change without notice.
TOTAL
Total Merchandise.........................................$_______________
QUANTITY
Your complete charge card number, its expiration date and your
signature are necessary to process all charge card orders.
$17.00
$17.00
$28.45
$28.45
✂
For credit card purchases
Replacement handset battery (black)
Replacement handset battery (white)
AC power supply adapter (black)
CATALOG NUMBER
DESCRIPTION
AC power supply adapter (white)
ACCESSORY ORDER FORM
CUSTOMER: CUT ALONG DOTTED LINE.
Model 2-9917/2-9918
15363420 (Rev. 2 E/S)
98-37
Printed in Thailand
© 1998 Thomson Consumer Electronics, Inc.
P.O. BOX 1976, Indianapolis, IN 46206
Trademark(s) ® Registered
Marca(s) Registrada(s)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising