dishwasher Instruction manual

dishwasher Instruction manual

Below you will find brief information for dishwasher. This dishwasher has a capacity of 12 place settings and can be used to wash a variety of dishes, pots, and pans. It features a variety of programs, including a soak program, a rapid program, an ECO program, a half load program, and an ultra clean program. The dishwasher also has a number of options, including a Flexi Tabs option, a HYCLEAN option, a Spread Half Load option, and a Program Delay option. The dishwasher also has a water softening system, which uses a special regenerating salt to reduce the hardness of the water.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Dishwasher Instruction Manual | Manualzz

INSTRUCTION MANUAL

GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS

Contents

1.

Description of the controls ________________________________ 3

2.

Operating instructions ___________________________________ 13

3.

Cleaning and maintenance _______________________________ 25

4.

Troubleshooting _______________________________________ 29

Thank you for choosing one of our products.

You are advised to read this manual carefully; it contains all the information you need about the right conditions for the proper, safe use of your dishwasher.

The individual sections are laid out to provide you with a step-by-step guide to all your appliance's functions; the texts are easy to understand and are complete with detailed illustrations.

Recommendations are given for the correct use of the baskets, spray arms, containers, filters, washing programs, and for operating the controls.

Following the cleaning instructions provided here will keep your dishwasher's performance at peak levels in the long term.

This user-friendly manual will provide answers to all your questions about use of the dishwasher.

USER INSTRUCTIONS: these consist of recommendations for using the appliance, a description of its controls and of the correct cleaning and maintenance procedures.

1

2

User instructions

1. Description of the controls

1.1 Front panel

The ON/OFF is on the top edge of the panel, and all the dishwasher’s other controls and monitoring devices are on the central display.

Programming and option selection are only possible with the door

closed.

NOTA:

The displays illustrated in the instruction manual are purely guideline; symbols, programs and options may vary depending on the model purchased.

User instructions

VERSION WITHOUT OPTIONS

1 ON/OFF BUTTON

2 SELECTION PROGRAMS BUTTON

3 START/PAUSE BUTTON

4 PROGRAMS LIGHTS

5 PHASES/PROGRAM LIGHTS

6

WATER HARDNESS ADJUSTMENT ON INDICATOR LIGHT

The light flashes to indicate that the appliance is in “water hardness adjustment” mode.

SALT WARNIN LIGHT

Illumination of this light denotes a regenerating salt warning level.

7 NO RINSE AID LIGHT

3

User instructions

VERSION WITH OPTIONS

4

1 ON/OFF BUTTON

2 SELECTION PROGRAMS BUTTON

3 START/PAUSE BUTTON

4 PROGRAMS LIGHTS

5 PHASES/PROGRAM LIGHTS +

6

PROGRAM DELAY (if the option is included)

WATER HARDNESS ADJUSTMENT ON INDICATOR LIGHT

The light flashes to indicate that the appliance is in “water hardness adjustment” mode.

SALT WARNIN LIGHT

Illumination of this light denotes a regenerating salt warning level.

7 NO RINSE AID LIGHT

8 OPTIONS (on some models only)

User instructions

<<OPTIONS (8)>>

Depending on the model, this zone may contain one or more of the following options, identified by the relative symbols and described in more detail in the relevant sections of the manual.

It is not possible to select any options when the soak program is being used. All options except "Flexi Tabs" are disabled at the end of the wash cycle. To disable the “Flexi Tabs” option, press the relative button (the light goes out).

Flexi Tabs

Specifically for the use of products which contain salt and rinse aid as well as detergent.

HYCLEAN

Adds a final antibacterial rinse to the selected program.

Spread HALF LOAD WASH

Allows washing of just a few dishes placed in both baskets.

PROGRAM DELAY

Allows the program to be set to start with a delay of 3, 6, 9 or

12 hours.

PROGRAMS TABLE

The manual contains the programs table for several models. To find the table for your dishwasher, compare the program symbols at the top of the table with those on your control panel.

5

User instructions

PROGRAMS TABLE

PROGRAMME

NUMBER

& SYMBOL

LOAD CROCKERY AND

CUTLERY

PROGRAM

PROGRESS

DURATION

MINUTES

(1)

CONSUMPTION

WATER

LITRES

POWER

KWh (1)

1 SOAK

Pans and dishes awaiting completion of the load

Cold prewash

15 3,5 0,02

2 RAPID

Dishes with light dirt, washed immediately after use

Wash at 38°C

Rinse at 50°C

27 6,5 0,70

3 ECO (*)

EN 50242

Dishes with normal dirt, even with dried-on residues

Cold prewash

Wash at 45°C

Rinse at 65°C

Dry

** ** **

4 HALF LOAD

Half load of dishes with normal dirt, washed immediately after use.

Wash at 65°C

Cold rinse

Rinse at 70°C

Dry

90 11 1,20

5 ULTRA

CLEAN

Very dirty pans and dishes, even with dried-on residues.

Hot prewash

Wash at 70°C

Cold rinse (2)

Rinse at 70°C

Dry

155 15,5 1,60

****

The ULTRA CLEAN program terminate with an extra anti-bacteria rinse that ensures a further reduction in the bacteria level. If the temperature falls during this stage of the program (e.g. because the door is opened or due to a power blackout), the program lights (4) flash to warn that the anti-bacteria effect is not guaranteed.

IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.

If the dishwasher door is open or not properly closed, the washing cycle will not start.

6

User instructions

NOTES AND REFERENCES

Only run the soak program with half loads.

Options cannot be used with the soak program.

* Standard programme under EN 50242.

** See information sheet provided

*** IEC/DIN reference programme.

**** Reference program for laboratories: Detergent: 20g in the dispenser + 10g in the door or tablet. Configuration: see photo in “Using the baskets”.

(1) Program consumption and duration figures have been measured in accordance with the EN 50242 standard. Values may vary depending on intake water and room temperatures and the type and quantity of dishes loaded.

(2) 1 or 2 cold rinses depending on the model.

REFERENCES for the ENERGY LABEL supplied with the dishwasher:

- Annual energy consumption is based on 280 standard wash cycles with cold water and consumption of low-energy operating modes. Actual consumption depends on the way in which the appliance is used.

- Water consumption is based on 280 standard wash cycles. Actual consumption depends on the way in which the appliance is used.

- Information refers to the EN 50242 STANDARD programme (identified in the programmes table), which is the most effective in terms of combined energy and water consumption. The programme is recommended for dishes with a normal level of dirt.

- Drying efficiency class on a scale from “G” (minimum efficiency) to “A”

(maximum efficiency).

7

User instructions

1.2 Washing programs

The dishwasher is equipped with a control panel, described in chapter

"3. Description of the controls", from which it is possible to carry out all the power switch-on, switch-off and programming operations.

Before starting a washing program make sure that:

The water supply tap is open.

The correct amount of detergent has been added to the

dispenser.

The baskets have been correctly loaded.

The spray arms are able to rotate freely and without obstruction.

The dishwasher door is securely closed.

SWITCHING ON

When the ON/OFF button (1) is pressed, the dishwasher switches on.

8

PROGRAMMING

Programming operations are only possible with the door closed.

PROGRAM SELECTION

Press the PROGRAM SELECTION button (2) several times until the light of the program required comes on.

User instructions

STARTING THE PROGRAM

To start the dishwasher, press the START/PAUSE button (3) for a few seconds, until the light of the first phase of the selected program starts to flash (confirmation beep).

As the program runs, the PHASES/PROGRAM lights (5) will indicate the current cycle status.

The light of the phase in progress will flash, while the lights of the subsequent phases remain on.

N.B. during execution of programs which do not include a prewash, the first PHASES/PROGRAM light (5) will remain off.

END OF PROGRAM

When the program finishes, a buzzer sounds briefly and all the

PHASES/PROGRAM lights (5) flash.

INTERRUPTION A PROGRAM

To interrupt a program in progress:

• press the START/PAUSE button (3 ) for a few seconds; the light of the phase in progress remains on and the light of the program in progress flashes (confirmation beep);

• you may now restart the program by pressing button (3) again until it restarts, or change or annul the program (see "C HANGING A

PROGRAM ", or "A NNULLING A PROGRAM ").

CHANGING A PROGRAM

To change the running program it is necessary:

• to interrupt the running program (see “I NTERRUPTION A PROGRAM ”);

• select the new program;

• start the program (see “S TARTING THE PROGRAM ”).

9

User instructions

10

ANNULLING A PROGRAM

To annul the program

• press the START/PAUSE button (3 ) for a few seconds; the light of the phase in progress remains on and the light of the program in progress flashes (confirmation beep);

Keep the START/PAUSE button (3) pressed until the PROGRAM

PHASES lights (5) go out (confirmation beep). The lights of programs 4 and 5 come on.

The water in the tank will be pumped out and the program will end at the point where it was interrupted. When the operation is complete, the

PROGRAM PHASES lights (5) flash.

In case that the door is opened during the operation, to the next door closing it is going to be necessary to start the program as shown in paragraph “ S TARTING THE PROGRAM ”. The program will resume from the point in which it was interrupted.

In case that the tub temperature is higher than 50°C the program

will start about 30 seconds later.

OPTION SELECTION

Options are selected by pressing the relative button by the symbol of the option required; the light comes on to confirm that the option has been activated.

It is not possible to select any options when the soak

program is being used.

All options except "Flexi Tabs" are disabled at the end of the wash cycle. To disable the “Flexi Tabs” option, press the relative button (the light goes out).

All options, including " Flexi Tabs " are disabled when a program is CANCELLED after it has begun.

User instructions

Flexi Tabs

Specifically for washing with combination detergents in tablets, which also contain salt and rinse aid (3in1) or other agents such as glass protector, steel rinse aids, etc. (4in1, 5in1…). When this option is selected, salt and rinse aid will not be dispensed even if the relative compartments contain them. If the containers are empty, the lights will remain on.

With short programs, because there is less time for them to dissolve, tablets may fail to wash effectively and undissolved residues may be left.

Powder detergents are more suitable for these programs.

If the option is not provided, we recommend the use of conventional

products (separate detergent, salt and rinse aid), because with conventional washing cycles, combined products might create problems such as a white deposit, poor drying results and residues left on dishes.

For further information, refer to the detergent pack.

IMPORTANT: when no longer required, the option must be deactivated by pressing the relative button (the light goes out).

These products are not suitable for use with excessively “hard” water.

If the hardness level set is higher than H3, when the option is activated the relative light flashes to indicate that the product is being used incorrectly; the dishwasher will still work, but washing results may be

poor.

PROGRAM DELAY

The PROGRAM DELAY button can be pressed to delay the start of the washing program by 3,6 or 9 hours, indicated by the PROGRAM

DELAY/PROGRAM PHASES (5) lights. This function allows you to set the dishwasher to work at your preferred time of day.

After selecting the delay, start the program (see relative section).

The appliance will prewash the dishes, after which the “program delay” set previously will come into effect (option light and light of selected

program on).N.B.: It is not possible to select the PROGRAM DELAY option once the cycle has begun.

Remaining program delay time: with this option active, the user can view the time left before the washing cycle starts.

• press the START/PAUSE button (3); the light of the first phase (5) of the selected program (4) comes on, while the program light flashes (confirmation beep);

• press the PROGRAM DELAY button. One of the PROGRAM

DELAY lights (5) will flash to indicate whether less than 3, 6, 9 or

12 hours are left before the dishwasher starts.

11

User instructions

HYCLEAN

The "HYCLEAN" option prolongs the final hot rinse to ensure a further reduction in the bacteria level. If the temperature in the tank falls during this stage of the program (e.g. because the door is opened or due to a power blackout), the light of the option and the program lights flash to warn that the additional washing phase has not been completed successfully.

This does not mean that the wash program has been less effective than usual.

SPREAD HALF LOAD

Suitable when there are not many dishes to be washed, it saves energy and reduces the program duration. Place dishes in both baskets then load the detergent dispenser than less than the normal amount for a full load.

TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT

Always try to run the dishwasher fully loaded.

Do not wash the dishes in running water.

Use the washing program that is most appropriate for each type of load.

Do not carry out any preliminary rinsing.

If available, connect the dishwasher to a hot water supply up to

60°C.

TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT

THE ENVIRONMENT

The phosphates contained in dishwasher detergents are harmful to the environment. To avoid using excessive amounts of detergent and to save on electricity, observe the following:

separate the more delicate items from dishes that are more resistant to aggressive detergents and high temperatures;

do not pour the detergent directly on the dishes.

ENERGY MANAGEMENT

After 5 minutes of waiting (washing cycle completed, stopped or set but not started) the dishwasher switches to a standby state to reduce energy consumption.

In this state, the dishwasher indicator panel (lights or display depending on model) functions more slowly (switch-on once every 5 seconds).

REMOVING THE DISHES

At the end of the washing program, wait at least 20 minutes before removing the dishes, to allow them to cool down. To prevent any water droplets on the upper basket from falling on the dishes in the lower basket, it is advisable to unload the lower basket first, and then the upper basket.

12

User instructions

2. Operating instructions

Once the dishwasher has been correctly installed, prepare for use as follows:

Adjust the water softening system;

Add the regenerating salt;

Add the rinse aid and detergent.

2.1 Using the water softening system

The amount of scale contained in the water (water hardness index) can cause whitish staining on the dry dishes, which tend to become dull over time. The dishwasher is equipped with an automatic softening system which uses a special regenerating salt to reduce the hardness of the water.

The dishwasher is factory set for water hardness level 3 (average hardness

41-60°dF 24-31°dH ).

SALT

When using water of medium hardness, the regenerating salt container should be refilled after approximately 20 washing cycles. The salt container can hold approximately 1.7 Kg of salt in grains. The container is situated at the bottom of the dishwasher. After removing the lower basket, unscrew the salt container cap by turning it anticlockwise and pour in the salt using the funnel supplied with the dishwasher. Before replacing the cap, remove any salt residues from around the opening.

When using the dishwasher for the first time, in addition to the salt it is also necessary to add one litre of water to the container.

Each time the salt container is refilled, make sure that the cap is

securely closed. The mixture of water and detergent must never penetrate the salt container, as this would compromise the operation of the regeneration system. In the event of this occurring, the warranty will be invalidated.

Only use regenerating salt specially formulated for domestic dishwashers. If using salt tablets, do not fill the container

completely.

13

14

User instructions

Do not use table salt as it contains insoluble substances which, over time, may damage the water softening system.

When necessary, refill the regenerating salt container before

starting the washing program. In this way, the excess saline solution will be immediately removed by the water; the prolonged presence of salt water inside the tank may lead to corrosion.

Be careful not to confuse the salt and detergent packages; adding detergent to the salt container will damage the water softening system.

ADJUSTING THE WATER SOFTENING SYSTEM

The dishwasher is equipped with a device which allows the softener setting to be varied to suit the hardness of the mains water. The hardness is set using the PROGRAM SELECTION BUTTON (2).

To access the setting function, hold the button down for more than 15 seconds. The WATER HARDNESS ADJUSTMENT INDICATOR LIGHT

(6) flashes, while the SELECTED PROGRAM INDICATOR LIGHTS (4) show the current setting. Each pressure on the button changes the setting following the sequence in the table below:

>

User instructions

WATER HARDNESS TABLE

WATER HARDNESS

German degrees (°dH)

French

Degrees (°dF)

SETTING

0 - 6 0 - 11

All lights off

(no salt)

One light on

7 - 10 12 - 18

11 - 15 19 - 27

Two lights on

16 - 21 28 - 37

Three lights on

22 - 28 38 - 50

Four lights on

Five lights on

29 - 35 51 - 62

36 - 50 63 - 90

Two lights on

Contact your local water board for information on the hardness of your water supply.

After adjustment or display of the current setting, simply do not touch the button for a few seconds; the dishwasher will automatically return to standard mode, quitting the adjustment mode.

2.2 Using the rinse aid and detergent dispensers

The detergent and rinse aid dispensers are situated on the inner part of the door: the detergent

dispenser is on the left, and the

rinse aid dispenser is on the right.

With the exception of the SOAK program, before every washing cycle it is necessary to add the required amount of detergent to the detergent

dispenser. The rinse aid, on the other hand, should only be added as required.

15

User instructions

ADDING THE RINSE AID

The rinse aid helps the dishes dry faster and prevents the formation of scale deposits and staining; it is automatically added to the water during the final rinse cycle, from the container situated on the inner side of the door.

To add rinse aid:

Open the door.

Rotate the container cap anticlockwise by ¼ of a turn and remove it.

Add the rinse aid until the container is full (approximately 140 cc).

The optical level indicator on the side of the cap should be completely obscured. Refill the rinse aid when the optical level indicator becomes clear again, or when the rinse aid warning light illuminates.

Replace the cover and turn it in a clockwise direction.

Use a cloth to remove any spillage of rinse aid which might lead to the formation of excess foam.

ADJUSTING THE RINSE AID DISPENSER SETTING

The dishwasher is factory set for medium water hardness. However it possible to change the setting by turning the dispenser’s selector to the desired position: the amount of rinse aid dispensed is proportional to the selector position.

To adjust the rinse aid setting, rotate the dispenser cap through a quarter turn in an anticlockwise direction and remove it.

Then use a screwdriver to rotate the rinse aid selector to the desired position.

Replace the cap, turning it clockwise.

The amount of rinse aid must be increased if the washed dishes appear dull or feature circular stains.

If, on the other hand, the dishes are sticky or have white streaks, it is necessary to reduce the rinse aid setting.

16

User instructions

ADDING THE DETERGENT

To open the detergent dispenser cap, lightly press the button P. Add the detergent and close the cap carefully.

During the washing cycle, the dispenser will be opened automatically.

When a program with hot prewash is selected (see program table), extra detergent must be placed in the cavity G/H (depending on models).

Use only detergents specially formulated for dishwashers. For optimal washing results it is important to use a good quality detergent.

The detergent packs must be sealed and stored in a dry place to prevent the formation of lumps which may negatively affect washing results. Once opened the detergent packs should not be kept for too long, otherwise the detergent loses its effectiveness.

Do not use detergents formulated for washing dishes by hand, because they produce a great deal of foam and may negatively affect the operation of the dishwasher.

Add the correct amount of detergent. An insufficient amount of detergent will result in a partial removal of dirt from the dishes, whereas an excessive amount is wasteful and does not improve the washing results.

The market offers liquid and powder detergents with differing chemical compositions, which may contain phosphates, or be phosphate-free but contain natural enzymes.

- Detergents containing phosphates are more effective against grease and starch at temperatures above 60°C .

- Enzyme detergents, on the other hand, are also effective at lower temperatures (from 40 to 55°C ) and are more easily biodegradable. With enzyme detergents it is possible to obtain at low temperatures comparable results to those which can only be achieved at 65°C using traditional detergents.

For the safeguarding of the environment we recommend the use of

phosphate- and chlorine free detergents.

17

User instructions

The introduction of detergent into the rinse aid dispenser, even in liquid form, will damage the dishwasher.

2.3 General warnings and recommendations

Before using the dishwasher for the first time, it is advisable to read the following recommendations concerning dish types to be washed and their loading.

There are generally no constraints on the washing of domestic dishes, but in certain cases it is necessary to take their characteristics into account.

Before loading the dishes into the baskets it is necessary to:

• remove coarse food remains: e.g. bones, fish-bones, etc. which may clog the filter or damage the wash pump.

• soak any pots or pans with burnt-on food remains on the bottom to facilitate removal, then load them into the LOWER BASKET.

There is no need to pre-wash the dishes under running water before loading them into the baskets since this only wastes water.

Correct loading of the dishes helps ensure optimal washing results.

18

User instructions

WARNING!

Make sure that the dishes are securely in place so that they cannot tip over or obstruct the rotation of the spray arms during the washing cycle.

Do not place very small objects in the baskets as these could fall and obstruct the spray arms or the wash pump.

Containers such as cups, bowls, glasses and pots should always be loaded with the opening facing downwards and with any cavities at an angle, to allow the water to drain out.

Do not stack dishes or place them in such a way that they cover one other.

Do not place glasses too close together because they may knock against each other and break, or there might be staining at the point where they touch.

MAKE SURE that the items being washed are dishwasher-safe.

Items which are not dishwasher-safe:

Wooden dishes, pots or pans: these may be damaged by the high washing temperatures.

Handcrafted items: these are rarely suitable for washing in a dishwasher. The relatively high water temperatures and the detergents used may damage them.

Plastic dishes: heat resistant plastic dishes must be washed in the upper basket.

Dishes and objects in copper, tin, zinc or brass: these tend to stain.

Aluminium dishes: items made from anodised aluminium may lose their colour.

Silverware: silver items may stain.

Glass and crystal: in general, glass and crystal objects can be washed in the dishwasher. However, certain types of glass and crystal may become dull and lose their clearness after many washings. Therefore, for these items we recommend using the least aggressive program available.

Decorated items: the decorated objects available on the market are generally able to withstand washing in the dishwasher, although the colours may fade after a great many washes. If in doubt as to the fastness of the colours, it is advisable to wash just a few items at a time for approximately one month.

19

20

User instructions

2.4 Using the baskets

The dishwasher has a capacity of 12 place-settings, including serving dishes.

LOWER BASKET

The lower basket receives the full force of the lower spray arm, and should therefore be used for the “toughest” items with a heavier degree of soiling.

All types and combinations of loads are permitted, provided that the dishes, pots and pans are arranged with all the soiled surfaces exposed to the water jets coming from the bottom.

With fixed supports

To make the most of the space inside the basket when loading large items, certain models are equipped with tip-up supports for plates in 2 or 4 sections.

With tip-up supports

BOTTOM BASKET INSERTS

Some models are equipped with bottom basket inserts which improve the drying of dishes. The inserts are supplied in the accessories bag; to use them, simply fit them into place as shown.

User instructions

LOADING THE LOWER BASKET

Carefully load flat plates, soup plates, dessert and serving dishes, positioning them vertically. Pots, pans and their covers must be loaded upside down. When loading soup plates and dessert bowls, be sure to leave a gap between them.

Loading examples:

CUTLERY BASKET

The basket has removable top grids into which items of cutlery can be inserted to keep them properly spaced and allow water to pass between them effectively.

The cutlery supports and central lid are in the bag of accessories. The central lid is intended to act only as a cover: do not place the cutlery in it.

The cutlery should be arranged in an orderly manner inside the basket, with the handles pointing downwards. Take care during loading to avoid injury from the knife blades. The basket is suitable for all types of cutlery, except those long enough to interfere with the upper spray arm. Ladles, wooden spoons and cooking knives can be placed in the upper basket,

making sure that the knife blades do not protrude from the basket.

21

22

User instructions

UPPER BASKET

It is recommended to load the upper basket with small- or medium-sized items such as glasses, small plates, tea or coffee cups, shallow bowls and light objects made from heat resistant plastic. If the upper basket is used in the lowermost position, it can also be loaded with serving dishes, provided they are only slightly soiled.

LOADING THE UPPER BASKET

Load plates facing forward; cups, bowls etc. must always be facing downwards. The left side of the basket can be loaded with cups and glasses on two levels. In the centre section, plates and saucers can be loaded vertically into the supports provided.

Loading examples:

Examples of loading for intensive dirt :

User instructions

Depending on the models, the basket may be equipped with some or all of the following accessories:

Supports for cups or long objects (ladles, spoons…), on the left; can be tipped to the vertical position when not in use.

Long-stemmed glass holder, on the left; to use, simply lift and fix onto the hooks provided.

Cutlery racks, on the right, designed for knives and teaspoons; for teaspoons, pull out the sliding support. The racks can be tipped to the vertical position when not in use.

Fixed or movable racks in the middle. The movable supports can be fixed vertical, resting on the bottom of the basket when not in use, or set in the intermediate position, as required.

23

User instructions

ADJUSTING THE UPPER BASKET

The height of the top basket can be adjusted to allow large dishes or pans to be placed in the bottom basket.

The adjustment procedure may be type A or B, depending on the dishwasher model purchased.

Version A: pull-out with adjustment in two positions.

Pull out both the basket guides.

Remove the stops, first releasing them as shown in the diagram.

Pull out the basket.

Fit the upper or lower pair of wheels into the guide, depending on the setting required ;

Return the stops to their original position.

The left hand and right hand sides of the basket must always be set at

the same height.

Version B: with adjustment in three positions on both sides.

The sides of the basket must always be set at the same height.

Raise the basket by pulling on the top edge (1), to the first or second catch depending on the height required.

To lower the basket, first release it by pulling the release lever (2).

Adjustment is also possible with the basket loaded, but in this case when lowering the basket it should be held steady with one hand to avoid knocking the dishes.

24

User instructions

3. Cleaning and maintenance

Before carrying out any work, always unplug the appliance from the electrical supply or switch off the all-pole disconnection device.

3.1 General warnings and recommendations

Avoid the use of acidic or abrasive detergents.

Clean the outer surfaces and door-lining of the dishwasher regularly using a soft cloth moistened with water or with a normal detergent suitable for painted surfaces. Clean the door gaskets with a damp sponge. Periodically (once or twice a year) it is advisable to clean the tank and gaskets, using a soft cloth and water to remove any deposits.

CLEANING THE WATER INTAKE FILTER

The water intake filter A located at the outlet of the water supply tap needs to be cleaned periodically.

After having closed the water supply tap, unscrew the end of the water intake hose, remove the filter A and clean it delicately under running water. Reassemble filter A in its seat and carefully screw the water intake hose back into position.

CLEANING THE SPRAY ARMS

The spray arms can be easily removed for periodic cleaning of the nozzles, to prevent possible clogging. Wash them under running water and carefully replace them in their seats, checking that their rotary

movement is in no way impeded.

To remove the upper spray arm, unscrew locking ring R.

To remove the lower spray arm, simply lift it up, pulling by the central part.

To remove the orbital spray arm assembly, take hold of the longer arm and pull the orbital unit upward. Wash the arms under a jet of running water and return them carefully to their seat. After

reassembly, check that the spray arms turn freely. Otherwise, check that they have been installed correctly.

ORBITAL

25

User instructions

CLEANING THE FILTER UNIT

It is advisable to periodically inspect the centre filter C and, if necessary, to clean it. To remove the filter, grip the tabs, turn them anticlockwise and lift upwards;

• push the centre filter D from the underside to remove it from the micro-filter:

• separate the two parts which make up the plastic filter by pressing the body of the filter in the zone shown by the arrows;

• remove the centre filter by lifting it upwards.

26

GENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT

MAINTENANCE:

The filters should be cleaned under running water using a stiff brush.

When removing the filter, take care that there are no food residues on it. If any residues fall into the washing pit they might block hydraulic components, or foul the spray arm nozzles.

It is essential to thoroughly clean the filters according to the above instructions: the dishwasher cannot function if the filters are clogged.

Carefully replace the filters in their seats, to avoid damaging the wash pump.

PROLONGED DISUSE:

Run the soak program twice in succession.

Unplug the power cord from the socket.

Leave the door slightly open, in order to prevent the formation of unpleasant odours inside the washing tank.

Fill the rinse aid dispenser.

Shut off the water supply tap.

User instructions

BEFORE STARTING THE DISHWASHER AFTER PROLONGED

DISUSE:

Check that there are no deposits of sludge or rust inside the water pipe: if there are, allow the water to run from the water supply tap for a few minutes.

Plug the power cord back into the socket.

Reconnect the water intake hose and open the tap again.

TROUBLESHOOTING MINOR PROBLEMS

In some cases it is possible to remedy minor problems by referring to the following instructions:

If the program fails to start, check that:

• the dishwasher is connected to the electrical power supply;

• there is no power failure;

• the water tap is open;

• the dishwasher door is properly closed.

If water remains inside the dishwasher, check that:

• the drain hose is not kinked;

• the drain siphon is not obstructed;

• the dishwasher filters are not clogged.

If the dishes are not being cleaned properly, check that:

• the correct amount of detergent has been added;

• there is regenerating salt inside the special container;

• the dishes are being loaded correctly;

• the selected program is suitable for the dish types and their degree of soiling;

• all the filters are clean and positioned correctly;

• the spray arm nozzles are not obstructed;

• there is no object obstructing the rotation of the spray arms.

27

User instructions

If the dishes fail to dry or remain dull, check that:

• there is rinse aid inside the special container;

• the rinse aid dispenser setting is correct;

• the detergent used is of good quality and has not lost its effectiveness (for example, through incorrect storage, with the box left open).

If the dishes show signs of streaking, staining, etc., check that:

• the rinse aid dispenser setting is not too high.

If there are visible traces of rust inside the tank:

• the tank is made of steel, and therefore any rust marks are due to external elements (fragments of rust from the water pipes, pots, cutlery, etc.). Special products are commercially available to remove such marks;

• check that the amount of detergent being used is correct. Certain detergents can be more corrosive than others.

• check that the cap of the salt container is securely closed, and that the water softening setting is correct.

If after following the above troubleshooting instructions the problem persists, call the nearest After-Sales Centre.

WARNING: any operations performed on the appliance by unauthorised persons are not covered by the warranty and shall be

paid for by the user.

28

E1

E2

E3

E4

E5

E6

User instructions

4. Troubleshooting

The dishwasher is capable of signalling a number of faults through the simultaneous illumination of several indicator lights, with the following meanings:

FAULT DESCRIPTION

Acquastop failure

The anti-flooding system has been activated.

The system is tripped in case of water leaks.

Contact the after-sales service.

Safety level

The system which limits the water level inside the dishwasher has been tripped. Interrupt the program and switch off the dishwasher. Switch the dishwasher back on, program it again and start the washing cycle. If the problem persists, contact the after-sales service.

Water heating malfunction

The water is not heated or the heating parameters are not correct. Repeat the washing program; if the problem persists, contact the after-sales service.

Water temperature monitoring malfunction

Interrupt the program and switch off the dishwasher. Switch the dishwasher back on, program it again and start the washing cycle. If the problem persists, contact the after-sales service.

Water intake malfunction

The appliance does not take in water or does not do so correctly. Check that the water connections are correct, the water intake tap is turned on and the filter is not fouled. If the problem persists, contact the after-sales service.

Water pump-out malfunction

The appliance does not pump out the water or does not do so correctly. Check that the drain hose is not kinked or crushed and that the siphon and filter are not fouled. If the problem persists, contact the after-sales service.

29

User instructions

E7

E8

E9

FAULT DESCRIPTION

Turbine flow-regulator malfunction

The appliance is not able to "measure" the amount of water loaded accurately. Interrupt the program and switch off the dishwasher.

Switch the dishwasher back on, program it again and start the washing cycle. If the problem persists, contact the after-sales service.

Alternate washing system malfunction

Interrupt the program and switch off the dishwasher. Switch the dishwasher back on, program it again and start the washing cycle. If the problem persists, contact the after-sales service.

Water intake system malfunction

Contact the after-sales service.

Light off Light on Light flashing

If an alarm occurs the appliance interrupts the program in progress and signals a fault.

Alarms E1, E2, E3, E4, E8 and E9 interrupt the current program immediately.

The E5, E6 alarms interrupts the running program once the cause is resolved, it will bring bach the execution of the program.

The alarm E7 is visualized at the end of the cycle that comes, however, brought to the end since the operation of the dishwasher is not harmed.

To “reset” an alarm is necessary:

Open and close the door, or turn off and on the machine. At this point is possible to program the dishwasher again.

If the malfunction persists, contact your authorised Service Centre.

30

Capacity

Water supply pressure

Electrical characteristics

User instructions

TECHNICAL DATA

Width

Depth measured flush with the outer edge of the control panel

Height (depending on models)

597

÷

599 mm

Free standing: 600 mm

Semi-integrated: 570 mm

Free standing: from 850 mm to 890 mm

from 890 mm to 930 mm

Semi-integrated: from 820 mm to 890 mm

from 860 mm to 930 mm

12 Standard place settings min. 0,05 - max. 0,9 MPa (min. 0.5 – max. 9 bar)

See rating plate

31

advertisement

Key Features

  • 12 place settings capacity
  • Variety of washing programs
  • Water softening system
  • Multiple options for washing
  • Easy to use controls

Frequently Answers and Questions

How do I adjust the water softening system?
To adjust the water softening system, hold the PROGRAM SELECTION BUTTON (2) down for more than 15 seconds. The WATER HARDNESS ADJUSTMENT INDICATOR LIGHT (6) flashes, while the SELECTED PROGRAM INDICATOR LIGHTS (4) show the current setting. Each pressure on the button changes the setting following the sequence in the table below.
How do I load the dishwasher?
The dishwasher has a capacity of 12 place settings, including serving dishes. The lower basket receives the full force of the lower spray arm, and should therefore be used for the “toughest” items with a heavier degree of soiling. All types and combinations of loads are permitted, provided that the dishes, pots and pans are arranged with all the soiled surfaces exposed to the water jets coming from the bottom. The upper basket is recommended to load with small- or medium-sized items such as glasses, small plates, tea or coffee cups, shallow bowls and light objects made from heat resistant plastic.
What kind of detergent should I use?
Use only detergents specially formulated for dishwashers. For optimal washing results it is important to use a good quality detergent. The detergent packs must be sealed and stored in a dry place to prevent the formation of lumps which may negatively affect washing results.

Related manuals

Download PDF

advertisement