Cino | Fuzzyscan | Specifications | Cino Fuzzyscan Specifications

Cino Fuzzyscan Specifications
BARCODE IMAGER
Programming Manual
International Edition, Rev. C4
Revision History
Rev. No.
Released Date
Rev.B Beta
Apr. 16, 2009
Description
First Release
Programming Manual
FuzzyScan
Page 22
Page 25
Page 46
Code 128/EAN-128 Setting – Modify ISBT Concatenation Off option code to “4”
and ISBT Concatenation On option code to “5”.
GS1 Databar Setting – All GS1 databar default values are changed to Enable.
Add “Symbology ID Table”.
June 22, 2009
Page 34
Page 37
Add “Presentation Scanning Mode”.
Add “Time Delay to Low Power Mode”.
Rev.B2
Aug. 21, 2009
Page 9, 11 Add “PDF417/Micro PDF417”, “Codablock F”, “Korea Post Code”.
Page 26
Add “Composite Code Setting”, “PDF/Micro PDF417 Setting”,
“Codablock F Setting”, Korea Post Code Setting”.
Page 39
Add “SmartStand Power Off Timeout”.
Page 46
Add “PDF417/Micro PDF417”, “Codablock F”, “Korea Post Code” into
Condensed DataWizard Table.
Page 48
Add “PDF417/Micro PDF417”, “Codablock F”, “Composite Code”,
“Korea Post Code” IDs into Symbology ID Table.
Rev.B3
Oct. 16, 2009
Page 8
Add “IBM PS/2, 25-30 series keyboard wedge interface”.
Page 39 Add “Presentation Scanning Auto-sense”.
Page 48 Add “Code 128” ID into Symbology ID Table.
Rev.B
May 05, 2009
Rev.B1
Rev.B4
Mar. 05, 2010
Page 15
Page 33
Page 35
Page 38
Page 54
Modify UPC-E/EAN-8 expansion and UPC-A standardization
Rename “Time Out Control” to “Serial Response Time-out”.
Rename “Presentation Scanning Mode” to “Presentation Control”.
Rename “Auto Power Off Duration” to “Light Source On Time”.
Add “Extremely short” option to Good Read Duration.
Rename “Presentation Scanning Auto-sense” to “Presentation Auto-sense”.
Add “Presentation Sensitivity”
System Commands – Add “Master Default” quick set command.
Page 38
Page 39
Hands Free Time-out – Add “Disable”.
Add “Trigger Control” (only available for FuzzyScan F460/F468).
Page 39
Rev. B5
Apr.12, 2010
Revision History
Rev. No.
Released Date
Rev. B6
May 27, 2010
Page 33
Baud Rate – Add 57.6K BPS and 115.2K BPS.
Jun 25 , 2010
Page 17
Page 38
Add “UPC/EAN Security Level”.
Add “Immediate” parameter (option 5) to "Time Delay to Low Power Mode"
and change the default value from 5 seconds to immediate.
Page 15,16
Page 17
Page 28
Page 37
Page 38
Add “ Supplement Scan Voting”.
Add “EAN Supplement Control”.
Keyboard Layout – Add “Czech (QWERTY)”, remove “Universal”, and rename
Spain (QWERTY) to Spain (Spanish QWERTY), Latin America (QWERTY) to
Spain (Latin America, QWERTY).
Add “Good Read Indicator”.
“Scan Rate Control”.
Rev. B7
Programming Manual
FuzzyScan
Rev. B8
Description
Sep 29 , 2010
Rev. B9
Nov 10 , 2010
Page 34
Baud Rate – Cancel Baud Rate 300/600 BPS.
Rev. C1
Mar 04, 2011
Page 34
Baud Rate – Revise 57.6K BPS and 115.2K BPS option code from 6.7. to 8.9.
Mar 22, 2011
Page 13
Page 35
Add ”Code 39 Security Level”.
Add “NAK Retry Count”.
Add “ACK/NAK Transmission Indication”.
Rev. C2
Rev. C3
Jul 22, 2011
Page 9, 19, 24, 51 UCC/EAN-128 was renamed GS1-128
Page 35
Add new parameters to “ACK Indication”
Page 36
Modify “Serial Response Time-out” parameters.
Page 44
Add “Laser Aiming Control” function.
Rev. C4
Nov 04, 2011
Page 14
Add “Codabar Check Digit Settings”
© Copyright Cino Group
© Copyright PC Worth Int’l Co., Ltd
Cino makes no warranty of any kind with regard to this publication, including, but not limited to, the implied warranty of
merchantability and fitness for any particular purpose. Cino shall not be liable for errors contained herein or for incidental
consequential damages in connection with the furnishing, performance, or use of this publication. This publication contains
proprietary information that is protected by copyright. All rights are reserved. No part of this publication may be photocopied,
reproduced or translated into any language, in any forms, in an electronic retrieval system or otherwise, without prior written
permission of Cino. All product information and specifications shown in this document may be changed without prior notice.
Programming Manual
FuzzyScan
Warranty
Cino warrants its products against defects in workmanship and materials from the date of shipment, provided that the
product is operated under normal and proper conditions. The warranty provisions and durations are furnished by different
warranty programs. The above warranty does not apply to any product which has been (i) misused; (ii) damaged by accident
or negligence; (iii) modified or altered by the purchaser or other party; (iv) repaired or tampered by unauthorized
representatives; (v) operated or stored beyond the specified operational and environmental parameters; (vi) applied
software, accessories or parts are not supplied by Cino; (vii) damaged by circumstances out of Cino’s control, such as, but
not limited to, lightning or fluctuation in electrical power. Any defective product must follow the warranty program and RMA
procedures to return Cino for inspection.
Regulatory
FCC part 15B
EN55022, EN55024, EN61000-3-2, EN61000-3-3
CNS13438
Industry Canada ICES-003
LED Eye Safety
IEC60825-1, EN60825-1
Table of Contents
Getting Started
Getting Familiar with Your FuzzyScan
1
Connecting to Your Host
1
Using Accessories
2
Configure Your FuzzyScan
Programming Manual
FuzzyScan
Bar Code Programming Manual
3
Programming Procedures
4
Host Interface Selection
8
Symbology Reading Control
9
Keyboard Interface Control
23
Serial Interface Control
32
Wand/Laser Emulation Control
35
Operation Control
36
Condensed DataWizard
41
Appendix
Symbology ID Table
48
Keyboard Function Code Table
49
ASCII Input Shortcut
50
Host Interface Quick Set
51
Operation Mode Quick Set
52
Option Codes
53
System Commands
54
Getting Started
Getting Familiar with Your FuzzyScan
Connecting to Your Host
Thank you for choosing Cino FuzzyScan Imager. All
FuzzyScan imagers deliver world-class performance for a
broad range of applications to unleash your productivity. This
document provides an easy reference for installation and
operation purposes. A complete documentation is provided
by the FuzzyScan Programming Manual available at
www.cino.com.tw.
FuzzyScan imagers support PS/2(DOS/V) Keyboard
Wedge, RS-232 Serial, and USB interfaces. Please
choose your desired interface cable, then plug it into the
cable interface port of the imager and connect it to the
host. If you would like to remove the cable, please
straighten one end of a paper clip, then insert it into the
cable release hole to pull out the cable.
F700 & L700 Series
Programming Manual
FuzzyScan
USB
F600 & L600 Series
Power Indicator
Status Indicator
RS232 Serial
Trigger
Scan Window
Beeper
Cable Release Hole
F400 Series
PS/2(DOS/V) Keyboard Wedge
1
Getting Started
Using Accessories
You can enhance productivity of your workforce by using
various accessories to fulfill a wide variety of application
demand.
Universal Holder
A stylish Universal Holder is designed for
storing your imager when not in use. It
serves
to
protect
the
imager
from
lens-scratched or falling. Moreover, its
artistic-design enhances the entire value
of the imager.
Programming Manual
FuzzyScan
Hand-free SmartStand
A SmartStand is specifically designed
for hand-free applications to maximize
user’s comfort and productivity. You
can adjust the scanner holder to
desired
position
for
optimized
scanning.
Thanks to the auto-sense design, the
imager is capable of switching
between presentation scanning and
hand-held scanning automatically
while working with SmartStand.
Please note that the SmartStand is
not applicable for F400 Series imager.
2
Configure Your FuzzyScan
Bar Code Programming Menu
The FuzzyScan bar code commands are specially designed
Proprietary bar code labels which allow you to set the
FuzzyScan internal programming parameters. There are
System Command, Family Code and Option Code for
programming purpose.
System Command
The System Command is the highest level bar code
command which directs FuzzyScan to perform immediate
operations, such as entering programming mode
(PROGRAM), exiting programming mode (EXIT), listing
system information (SYSLIST), recovering to factory
preset configurations (M_DEFAULT) and so on. Please
note that all system commands will take a few seconds to
complete the operations. User must wait for the
completion beeps before scanning another bar code.
Programming Manual
FuzzyScan
Each programmable family and bar code command label is
listed on the same page with major system commands. The
detailed explanations and special programming flowchart are
printed on facing or following pages. You can read the
explanation and set the FuzzyScan concurrently.
A supplemental bar code command menu incorporates the
bar code command labels of System Command and Option
Code. As you set the FuzzyScan, open the bar code
command menu to find the option code page. You may scan
the desired family code and option code to set FuzzyScan. If
you want to change the programming family for multiple
settings, you need only turn over the programming page to
find next desired programming family.
Family Code
The Family Code is scanned to select the user desired
programming family. FuzzyScan has already provided
more than one hundred programming families to meet any
specific requirements.
Option Code
The Option Codes is a set of bar code commands
represented by “0–9”, “A–F” and finishing selection (FIN).
For most setting, you must select at least one option code
following the family code selection to set the desired
parameter for the selected programming family.
3
Configure Your FuzzyScan
Programming Procedures
Programming Manual
FuzzyScan
As you scan the bar code command to select the desired
parameters, information about the final selected parameters
represented by the bar code commands are stored in the
FuzzyScan’s internal Flash Memory ASIC or non-volatile
memory. If you turn off the unit, the Flash Memory ASIC or
non-volatile memory retains all programming options. You
need not re-program the FuzzyScan if you want to keep the
existing configurations in the next power on.
If the programming family must take multiple scans
selection, cycling scan selection, or dual level selection
procedures, the family of the programming menu will be
marked with the matched representing symbol of
Programming Category (P.C.) in bold font listed in the
following table. You can easily find the bold mark in the
programming menu, and refer to their flowcharts for details.
Before setting the FuzzyScan, please also refer to the
“Beeping Indications” listed in Appendix to understand the
details of programming beeping indications. It will be very
helpful for you to know the existing status while you are
programming the FuzzyScan.
The programming procedures of FuzzyScan are designed
as simple as possible for ease of setting. Most
programming families take the Single Scan Selection
programming procedure. But several programming families
have more complex and flexible programmable options,
and you must take Multiple Scans Selection, Cycling
Scan Selection or Dual Level Selection to complete their
programming procedures. Each kind of programming
procedure is listed in the following pages for your reference.
Please give careful attention to become familiar with each
programming procedure.
Conventions of Programming Menu
Conventions
Descriptions
Factory Default Value
P.C.
Programming Category
SS : Single scan selection
MS : Multiple scans selection
CS : Cycling scan selection
DS : Dual level scan selection
4
(
)
Necessary Option Code
[
]
Selectable Option Code
Configure Your FuzzyScan
Program & End
System List, Group & Master Default
Scan
“PROGRAM”
Scan
“SYSLIST”
FuzzyScan will enter programming mode,
and inhibit all non-programming functions.
revision number to host via selected host interface,
FuzzyScan will list the product information and
Programming Manual
FuzzyScan
then issue the completion beeping.
Scan
“END”
Scan
“M_DEFAULT”
FuzzyScan will exit programming mode, and store all
parameters in Flash Memory ASIC or non-volatile memory,
then issue the completion beeping.
FuzzyScan will recover all programmable
parameters into factory preset configurations,
then issue the completion beeping.
Please note that the FuzzyScan will take 3-4 seconds to
store parameters in internal Flash Memory ASIC or
non-volatile memory after you scan the “END”. Please
don’t turn off the power before the completion beeping. It
may destroy all configured parameters.
5
Configure Your FuzzyScan
Single scan selection
Scan
“PROGRAM”
Scan
One of Family Codes
Multiple scans selection
Scan
“PROGRAM”
Enter programming mode.
Select one of desired
Select one of desired
Scan
programming families.
One of Family Codes
programming families.
1. Select one or several
Select one option code of
Scan
One of Option Codes
Enter programming mode.
Scan One or
Several Option Codes
desired parameter.
option codes to select
desired parameters.
2. If it’s necessary, scan
“FIN” to terminate
Programming Manual
FuzzyScan
Yes
Yes
Want to select another
Repeat
Selection
programming family?
Repeat
Selection
option code selection.
Want to select another
No
No
Scan
“END”
programming family?
Scan
Exit programming mode.
“END”
6
Exit programming mode.
Configure Your FuzzyScan
Cycling scan selection
Dual level selection
Scan
“PROGRAM”
Scan
One of Family Codes
Scan
“PROGRAM”
Enter programming mode.
Select one of desired
Scan
One of Family Codes
programming families.
Cycling select one or
Scan
One of Option Codes
desired parameters as
Programming Manual
FuzzyScan
(2nd) Scan One or
Several Option Codes
Scan “FIN”
Finish cycling selection.
of desired parameters.
1. Select one or several
parameters.
2. If it’s necessary, scan
“FIN” to terminate
(If necessary)
option code selection.
Yes
Want to select another
Repeat
Selection
programming family?
Want to select another
programming family?
No
Scan
“END”
programming families.
option codes of desired
scans selection.
Repeat
Selection
Select one of desired
Select several option codes
(1st) Scan
Several Option Codes
several option codes of
“Single” or “Multiple”
Yes
Enter programming mode.
No
Scan
“END”
Exit programming mode.
7
Exit programming mode.
Configure Your FuzzyScan
Host Interface Selection
Programming Manual
FuzzyScan
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Host Interface Selection
MS
MS
MS
MS
MS
MS
MS
MS
MS
MS
Parameter Selection
IBM PS/2, 25-30 series keyboard wedge interface
Standard/TTL RS-232 peer-to-peer serial
Wand emulation
USB Com Port Emulation
PS/2 (DOS/V) direct link (keyboard replacement)
PS/2 (DOS/V) keyboard wedge turbo mode
PS/2 (DOS/V) keyboard wedge standard mode
Laser emulation
USB HID standard mode USB HID turbo mode
8
Option Code
02
06
08
09
10
13
14
17
18
19
Configure Your FuzzyScan
Symbology Reading Control
♦ User Defined Symbol ID ♦
Programming Manual
FuzzyScan
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Symbol ID : 1 character
DS
Parameter Selection
Code 128 (default=B)
GS1-128 (default=C)
UPC-A (default=A)
EAN-13 (default=F)
Codabar/NW-7 (default=D)
Code 39/Code 32 (default=G)
Code 93 (default=H)
Standard/Industrial 2 of 5 (default=I)
Interleaved 2 of 5 (default=J)
Matrix 2 of 5 (default=K)
China Postal Code (default=L)
German Postal Code (default=M)
IATA (default=O)
Code 11 (default=P)
MSI/Plessey (default=R)
UK/Plessey (default=S)
Telepen (default=T)
GS1 DataBar (default=X)
UPC-E (default=E)
EAN-8 (default=N)
Trioptic Code 39 (Default=W)
UCC Coupon Extended Code (Default=Z)
PDF417/Micro PDF417 (default=V)
Codablock F (default=Y)
Korea Post Code (default =a)
9
Option Code
2nd Option Code
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
26
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
Configure Your FuzzyScan
Symbology Reading Control
♦ Symbology ID Transmission ♦
Programming Manual
FuzzyScan
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Symbology ID Transmission
SS
SS
SS
SS
SS
SS
SS
Parameter Selection
Disable symbology ID transmission Enable prefix CINO symbology ID transmission
Enable suffix CINO symbology ID transmission
Enable both prefix and suffix CINO symbology ID transmission
Enable prefix AIM symbology ID transmission
Enable suffix AIM symbology ID transmission
Enable both prefix and suffix AIM symbology ID transmission
10
Option Code
0
1
2
3
4
5
6
Configure Your FuzzyScan
Symbology Reading Control
♦ Readable Bar Code Setting ♦
PROGRAM
Family Code Selection
P.C
Readable Symbology Setting
SS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
Programming Manual
Remember to scan “FIN” to terminate
FuzzyScan
F_DEFAULT
this selection. But if you select the
“ Auto ”, FuzzyScan will terminate this
selection automatically.
Parameter Selection
Auto Code 128 *
UPC-A *
UPC-E *
EAN-13 *
EAN-8 *
Codabar/NW-7 *
Code 39 *
Trioptic Code 39
Standard/Industrial 2 of 5
Matrix 2 of 5
Interleaved 2 of 5 *
China Postal Code
German Postal Code
Code 93 *
Code 11
MSI/Plessey
UK/Plessey
Telepen
GS1 DataBar (RSS-14) *
IATA
PDF417/Micro PDF417
Codablock F
Korea Post Code
Option Code
00
01
02
03
04
05
06
07
47
08
38
48
58
68
09
10
11
12
13
14
15
17
18
21
If your application is known, you may select those known symbologies only to increase the reading speed and decrease the possibility of reading error. Furthermore, to add
the “Symbology ID” into the transmitted data is also helpful to identify the specific symbology.
Above symbologies marketed with * are enable as default. When you select “Auto”, the imager only read those symbologies marked with *.
When you set the minimum and maximum length of each symbology, please note the data length of scanned bar code doesn’t include star/stop characters.
11
Configure Your FuzzyScan
Symbology Reading Control
♦ Code 39/Code 32 Setting ♦
Programming Manual
FuzzyScan
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
Code 39 Family Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Disable Code 39
Enable Code 39
Select Standard Code 39 as primary format Select Full ASCII Code 39 as primary format
Select Code 32 (PARAF, Italian Pharmaceutical) as primary format
Disable start/stop symbol transmission Enable start/stop symbol transmission
Disable Code 32 leading A transmission Enable Code 32 leading A transmission
Disable MOD 43 check digit verification Enable MOD 43 check digit verification
Disable check digit transmission Enable check digit transmission
Disable Code 39 buffering Enable Code 39 buffering
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
Trioptic Code 39 Setting
SS
SS
Disable Trioptic Code 39 Enable Trioptic Code 39
0
1
Code 39 Min. Length
SS
MS
Default (01) 01-Maximum
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Code 39 Max. Length
SS
MS
Default (98) 98-Minimum
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Trioptic Code 39 and Code 39 Full ASCII cannot be enabled simultaneously.
12
Configure Your FuzzyScan
Symbology Reading Control
♦ Code 39 Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Code 39 Security Level
SS
SS
SS
SS
Parameter Selection
Level 0
Level 1
Level 2 Level 3
Option Code
0
1
2
3
Programming Manual
FuzzyScan
Code 39 Security Level
The scanner offers four levels of decode security for Code39 bar codes:
Level 0: If you are experiencing misread of poorly-printed or serious out-of-spec. bar codes in level 1, please select level 0.
Level 1: If you are experiencing misread of poorly-printed or out-of-spec. bar codes in level 2, please select level 1.
Level 2: This is the default setting which allows the scanner to operate fastest, while providing sufficient security in decoding “in-spec” Code39 bar codes.
Level 3: If you failed to read poorly-printed or out-of-spec. bar codes in level 2, please select level 3. This is the most aggressive setting and may increase the misread.
13
Configure Your FuzzyScan
Symbology Reading Control
♦ Codabar/NW-7 Setting ♦
Programming Manual
FuzzyScan
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
Codabar Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Disable Codabar
Enable Codabar Select Codabar standard format Select Codabar ABC format
Select Codabar CLSI format
Select Codabar CX format
Disable start/stop symbol transmission Enable ABCD/ABCD start/stop symbol transmission
Enable abcd/abcd start/stop symbol transmission
Enable ABCD/TN*E start/stop symbol transmission
Enable abcd/tn*e start/stop symbol transmission
Disable check digit verification Enable check digit verification
Disable check digit transmission Enable check digit transmission
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
Codabar Check Digit Settings
SS
SS
SS
SS
SS
SS
SS
Modulus 16 Modulus 10/weight 3
Modulus 11
Modulus 10/weight 2
7 check DR
Weight Modulus 11
Runes (Modulus 10/weight 2)
0
1
2
3
4
5
6
Codabar Min. Length
SS
MS
Default (04) 01-Maximum
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
14
Configure Your FuzzyScan
Symbology Reading Control
♦ Codabar/NW-7 Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Codabar Max. Length
SS
MS
Parameter Selection
Default (98) 98-Minimum
FIN
(2 digits)
Programming Manual
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
FuzzyScan
Option Code
15
Configure Your FuzzyScan
Symbology Reading Control
♦ UPC-A & UPC-E Setting ♦
Programming Manual
FuzzyScan
PROGRAM
F_DEFAULT
Family Code Selection
P.C
UPC Family Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Parameter Selection
Option Code
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
Disable UPC-A
Enable UPC-A Disable UPC-E
Enable UPC-E Disable UPC-E expansion Enable UPC-E expansion
Disable UPC standardization Enable UPC standardization
Disable UPC numeric system
Enable UPC numeric system Disable UPC-A check digit transmission
Enable UPC-A check digit transmission Disable UPC-E check digit transmission
Enable UPC-E check digit transmission Disable UPC “leading 1” portion Enable UPC “leading 1” portion
When enable UPC-E expansion, the UPC-E decoded data will be converted to UPC-A format and affected by related setting, such as UPC standardization, UPC numeric
system, UPC-A check digit transmission.
UPC-E & EAN-8 Expansion
: Expand the 8-digit UPC-E and 8-digit ENA-8 to 12-digit UPC-A and 13-digit EAN-13.
UPC-A Standardization
: Expand the 12-digit UPC-A to 13-digit EAN-13 with 1 zero insertion.
UPC Lead 1 Numeric System
: Enable to read UPC leading with the 1 numeric system, you must enable this option.
WPC Selection
(UPC/EAN/CAN)
UPC-A
UPC-E
EAN-13
EAN-8
Basic Length
Disable
Check Digit
Disable
Numeric System
With 2-digit
Addendum
With 5-digit
Addendum
Enable
Standardization
Enable
Expansion
12
8
13
8
-1
-1
-1
-1
-1
-1
NC
NC
+2
+2
+2
+2
+5
+5
+5
+5
+1
+1
NC
NC
0
+4
0
+5
16
Configure Your FuzzyScan
Symbology Reading Control
♦ UPC-A & UPC-E Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
UPC Supplement Setting
SS
SS
SS
SS
SS
SS
SS
SS
Select UPC without supplement digits Select UPC with only 2 supplement digits
Select UPC with only 5 supplement digits
Select UPC with 2/5 supplement digits
Disable force supplement digits output Enable force supplement digits output
UPC Family Addenda Separator Off UPC Family Addenda Separator On
0
1
2
3
4
5
6
7
UPC/EAN Security Level
SS
SS
Level 0
Level 1 Level 2
0
1
Programming Manual
FuzzyScan
SS
Parameter Selection
Option Code
2
Only available for UPC-A & EAN-13
Supplement Scan Voting
SS
SS
SS
SS
SS
SS
SS
None
Level 1
Level 2
Level 3 Level 4
Level 5
Level 6
Level 7
Level 8
Level 9
Level 10
Level 11
Level 12
Level 13

0
1
2
3
4
5
6
7
8
9
A
B
C
D
UPC/EAN Security Level
The scanner offers three levels of decode security for UPC/EAN bar codes:
Level 0: If you are experiencing misread of poorly-printed or out-of-spec. bar codes, especially in characters 1, 2, 7, and 8 in level 1, please select level 0. Selection of this
security level may significantly impair the decoding ability of the scanner.
Level 1: This is the default setting which allows the scanner to operate fastest, while providing sufficient security in decoding “in-spec” UPC/EAN bar codes.
Level 2: If you are experiencing misread of poorly-printed, soiled or damage bar codes in level 1, please select level 2. This is the most aggressive setting and may
increase the misread.
The Supplement Scan Voting is the number of times the same UPC/EAN with 2/5 supplement digits has to be decoded before it is transmitted. It is helpful when decoding
a mix of UPC/EAN symbols with and without supplement digits. This function is effective when you select UPC/EAN with only 2 supplement digits, UPC/EAN with only 5
supplement digits or UPC/EAN with 2/5 supplement digits. The default value is Level 3. When you select higher level, it may impact the reading speed on poorly-printed,
low contrast or damage barcode labels.
17
Configure Your FuzzyScan
Symbology Reading Control
♦ EAN Setting, EAN Supplement Setting ♦
Programming Manual
FuzzyScan
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
EAN Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Disable EAN-13
Enable EAN-13 Disable EAN-8
Enable EAN-8 Disable EAN-8 expansion Enable EAN-8 expansion
Disable EAN-13 check digit transmission
Enable EAN-13 check digit transmission Disable EAN-8 check digit transmission
Enable EAN-8 check digit transmission Disable ISBN/ISSN Conversion reading check Enable ISBN/ISSN Conversion reading check
0
1
2
3
4
5
6
7
8
9
A
B
EAN Supplement Setting
SS
SS
SS
SS
SS
SS
SS
SS
Select EAN without supplement digits Select EAN with only 2 supplement digits
Select EAN with only 5 supplement digits
Select EAN with 2/5 supplement digits
Disable force supplement digits output Enable force supplement digits output
EAN Addenda Separator Off EAN Addenda Separator On
0
1
2
3
4
5
6
7
SS
None
Level 7
0
7
SS
Level 1
Level 8
1
8
SS
Level 2
Level 9
2
9
SS
Level 3 Level 10
3
A
SS
Level 4
Level 11
4
B
SS
Level 5
Level 12
5
C
SS
Level 6
Level 13
6
D
The Supplement Scan Voting is the number of times the same UPC/EAN with 2/5 supplement digits has to be decoded before it is transmitted. It is helpful when decoding
a mix of UPC/EAN symbols with and without supplement digits. This function is effective when you select UPC/EAN with only 2 supplement digits, UPC/EAN with only 5
supplement digits or UPC/EAN with 2/5 supplement digits. The default value is Level 3. When you select higher level, it may impact the reading speed on poorly-printed,
low contrast or damage barcode labels.
Supplement Scan Voting

18
Configure Your FuzzyScan
Symbology Reading Control
♦ EAN Security Level Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
UPC/EAN Security Level
SS
SS
SS
Parameter Selection
Level 0
Level 1 Level 2
Option Code
0
1
2
Only available for UPC-A & EAN-13
Programming Manual
FuzzyScan
EAN Supplement Control
SS
SS
SS
SS
SS
SS
SS
SS
Disable all specific prefix supplement digital output Enable all specific prefix supplement digital output
Enable 491 Supplement Digit Output
Enable 978/979 Supplement Digit Output
Enable 977 Supplement Digit Output
Enable 378/379 Supplement Digit Output
Enable 414/419 Supplement Digit Output
Enable 434/439 Supplement Digit Output
0
1
2
3
4
5
6
7
UPC/EAN Security Level
The scanner offers three levels of decode security for UPC/EAN bar codes:
Level 0: If you are experiencing misread of poorly-printed or out-of-spec. bar codes, especially in characters 1, 2, 7, and 8 in level 1, please select level 0. Selection of this
security level may significantly impair the decoding ability of the scanner.
Level 1: This is the default setting which allows the scanner to operate fastest, while providing sufficient security in decoding “in-spec” UPC/EAN bar codes.
Level 2: If you are experiencing misread of poorly-printed, soiled or damage bar codes in level 1, please select level 2. This is the most aggressive setting and may
increase the misread.
EAN Supplement Control
If you select EAN with only 2, or 5 or 2/5 supplement digits and enable 491 prefix supplement digit output, the scanner will transmit EAN with 2, or 5 or 2/5 supplement
digits bar codes starting with 491 prefix. The EAN without supplement digit will not be transmitted.
If you select EAN with only 2, or 5 or 2/5 supplement digits and enable the other except 491 prefix supplement digit output, the scanner will transmit EAN with 2, or 5, or 2/5
supplement digits bar codes starting with specific prefix. The EAN without supplement digit will be transmitted.
19
Configure Your FuzzyScan
Symbology Reading Control
♦ UCC Coupon Extended Code Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
UCC Coupon Extended Code
SS
SS
Parameter Selection
Disable UCC Coupon Extended Code Enable UCC Coupon Extended Code
Option Code
0
1
Programming Manual
FuzzyScan
UCC Coupon Extended Code
When UCC coupon extended code function is enabled, scanner decodes UPC-A barcodes starting with digit “5”, EAN-13 barcodes starting with digit “99” and GS1-128
Coupon Codes. UPC-A, EAN-13 and EAN-128 must be enabled to scan all types of Coupon Codes.
20
Configure Your FuzzyScan
Symbology Reading Control
♦ IATA & Interleaved 2 of 5 Setting ♦
Programming Manual
FuzzyScan
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
IATA Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Disable IATA Enable IATA
Select 15-digit fixed length IATA checking Select variable length IATA
Disable check digit verification Enable check digit automatic verification
Enable S/N checking digit verification only
Enable CPN checking digit verification only
Enable CPN, Airline and S/N check digit verification
Disable check digit transmission Enable check digit transmission
Disable start/stop symbol transmission Enable start/stop symbol transmission
0
1
2
3
4
5
6
7
8
9
A
B
C
Interleaved 2 of 5 Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
Disable Interleaved 2 of 5
Enable Interleaved 2 of 5 Select Interleaved 2 of 5 as primary format Select German Postal Code as primary format
No check character Validate USS check digit
Validate OPCC check digit
Disable check digit transmission Enable check digit transmission
0
1
2
3
4
5
6
7
8
21
Option Code
Configure Your FuzzyScan
Symbology Reading Control
♦ Code 25 Family Setting ♦
Programming Manual
FuzzyScan
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Code 25 Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Disable Standard/Industrial 2 of 5 Enable Standard/Industrial 2 of 5
Disable Matrix 2 of 5 Enable Matrix 2 of 5
Disable China Postal Code Enable China Postal Code
Disable check digit verification Enable check digit verification
Disable check digit transmission Enable check digit transmission
Code 25 Family Min. Length
SS
MS
Default (04) 01-Maximum
Option Code
0
1
2
3
4
5
6
7
8
9
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Code 25 Family Max. Length
SS
MS
Default (98) 98-Minimum
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
For Code25 setting, we recommend you to select only one type of Code 25 or set the maximum/minimum bar code length. To decode all types of Code 25 or to variable
length of Code 25 will increase the possibility of reading error.
22
Configure Your FuzzyScan
Symbology Reading Control
♦ Code 11 & Code 93 Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Code 11 Setting
SS
SS
SS
SS
SS
SS
SS
Disable Code 11 Enable Code 11
Disable check digit verification Select 1-check digit verification
Select 2-check digit verification
Disable check digit transmission Enable check digit transmission
Code 11 Min. Length
SS
MS
Default (04) 01-Maximum
Option Code
0
1
2
3
4
5
6
FIN
(2 digits)
Programming Manual
FuzzyScan
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Code 11 Max. Length
SS
MS
Default (98) 98-Minimum
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Code 93 Setting
SS
SS
SS
SS
Disable Code 93
Enable Code 93 Disable check digit transmission Enable check digit transmission
Code 93 Min. Length
SS
MS
Default (01) 01-Maximum
0
1
2
3
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Code 93 Max. Length
SS
MS
Default (98) 98-Minimum
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
23
Configure Your FuzzyScan
Symbology Reading Control
♦ MSI/Plessey Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
MSI/Plessey Setting
SS
SS
SS
SS
SS
SS
SS
Disable MSI/Plessy Enable MSI/Plessy
Select MOD 10 check digit Select MOD 10-10 check digit
Select MOD 11-10 check digit
Disable check digit transmission Enable check digit transmission
MSI/Plessey Min. Length
SS
MS
Default (04) 01-Maximum
Option Code
0
1
2
3
4
5
6
FIN
(2 digits)
Programming Manual
FuzzyScan
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
MSI/Plessey Max. Length
SS
MS
Default (98) 98-Minimum
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
24
Configure Your FuzzyScan
Symbology Reading Control
♦ Code 128 & UCC/EAN 128 Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Code 128/EAN-128 Setting
SS
SS
SS
SS
SS
SS
Disable Code 128 and GS1-128
Enable Code 128 and GS1-128 Disable function code conversion Enable function code conversion
ISBT Concatenation Off ISBT Concatenation On
Code 128/EAN-128 Min. Length
SS
MS
Default (01) 01-Maximum
Option Code
0
1
2
3
4
5
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Programming Manual
FuzzyScan
Code 128/EAN-128 Max. Length
SS
MS
Default (98) 98-Minimum
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
25
Configure Your FuzzyScan
Symbology Reading Control
♦ UK/Plessey Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
UK/Plessey Setting
SS
SS
SS
SS
SS
SS
SS
SS
Disable UK/Plessey Enable UK/Plessey
Select UK/Plessey Standard Format Select UK/Plessey CLSI Format
Disable Convert X to A-F Enable Convert X to A-F
Disable check digit transmission Enable check digit transmission
UK/Plessey Min. Length
SS
MS
Default (04) 01-Maximum
Option Code
0
1
2
3
4
5
6
7
FIN
(2 digits)
Programming Manual
FuzzyScan
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
UK/Plessey Max. Length
SS
MS
Default (98) 98-Minimum
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
26
Configure Your FuzzyScan
Symbology Reading Control
♦ Telepen Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Telepen Setting
SS
SS
SS
SS
SS
SS
Disable Telepen Enable Telepen
Select Telepen Numeric mode Select Telepen Full ASCII mode
Disable check digit transmission Enable check digit transmission
Telepen Min. Length
SS
MS
Default (04) 01-Maximum
Option Code
0
1
2
3
4
5
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Programming Manual
FuzzyScan
Telepen Max. Length
SS
MS
Default (98) 98-Minimum
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
27
Configure Your FuzzyScan
Symbology Reading Control
♦ GS1 DataBar Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
GS1 DataBar Setting
SS
SS
SS
SS
SS
SS
Disable GS1 DataBar (RSS-14)
Enable GS1 DataBar (RSS-14) Disable GS1 DataBar Limited
Enable GS1 DataBar Limited Disable GS1 DataBar Expanded
Enable GS1 DataBar Expanded GS1 DataBar Min. Length
SS
MS
Default (04) 01-Maximum
Option Code
0
1
2
3
4
5
FIN
(2 digits)
Only available for Expanded GS1 Databar.
Programming Manual
FuzzyScan
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
GS1 DataBar Max. Length
SS
MS
Default (74) 74-Minimum
FIN
(2 digits)
Only available for Expanded GS1 Databar.
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
28
Configure Your FuzzyScan
Symbology Reading Control
♦ Linear-stacked & Korea Post Code Setting ♦
Programming Manual
FuzzyScan
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Composite Codes Setting
SS
SS
SS
SS
Disable composite codes Enable composite codes
UPC Composite Mode: UPC never linked UPC Composite Mode: UPC always linked
0
1
2
3
PDF417/Micro PDF417 Setting
SS
SS
SS
SS
Disable PDF417
Enable PDF417 Disable MicroPDF417 Enable MicroPDF417
0
1
2
3
Codablock F Setting
SS
SS
Disable Enable
0
1
Korea Post Code Setting
SS
SS
Disable Enable
0
1
Length fixed in 6 characters.
Composite Codes Setting
If UPC Composite Mode: UPC never linked is selected, UPC barcodes are transmitted regardless of whether a MicroPDF417 symbol is detected.
If UPC Composite Mode: UPC always linked is selected, UPC barcodes are only transmitted when the MicroPDF417 is detected.
29
Option Code
Configure Your FuzzyScan
Keyboard Interface Control
♦ Keyboard Layout (Language) Setting ♦
Programming Manual
FuzzyScan
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Keyboard Layout
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Parameter Selection
Option Code
USA (QWERTY) France (AZERTY)
Germany (QWERTZ)
United Kingdom - UK (QWERTY)
Canadian French (QWERTY)
Spain (Spanish, QWERTY)
Sweden/Finland (QWERTY)
Portugal (QWERTY)
Norway (QWERTY)
Spain (Latin America, QWERTY)
Italy (QWERTY)
Netherlands (QWERTY)
Denmark (QWERTY)
Belgium (AZERTY)
Switzerland-Germany (QWERTY)
Iceland (QWERTY)
Japan (DOS/V)
Czech (QWERTY)
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
Please refer to the ASCII/HEX Table listed in the Appendix to determine HEX codes for characters, symbols, and functions to be used as preamble or postamble.
To set preamble or postamble as function key output, you must enable the “Function Key Emulation” feature as listed in page 3-25 first.
Keyboard Interface Message String :
Preamble
Data Length
Prefix Symbol ID
Scanned Data
Suffix Symbol ID
Postamble
Record Suffix
1-15 characters
2-3 digits
1 or 2 characters
Variable length
1 or 2 characters
1-15 characters
1 character
30
Configure Your FuzzyScan
Keyboard Interface Control
♦ Record Suffix, Preamble, Postamble & Caps Lock ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Record Suffix
SS
SS
SS
SS
SS
SS
None
RETURN TAB
SPACE
ENTER (Numeric Key Pad)
User defined character (1 character)
Preamble
SS
MS
None 1-15 characters
Option Code
0
1
2
3
4
5, (00-7F)
FIN
[00-7F], [FIN]
Maximum 15-character input; scan “FIN” to terminate this selection.
Programming Manual
FuzzyScan
Postamble
SS
MS
None 1-15 characters
FIN
[00-7F], [FIN]
Maximum 15-character input; scan “FIN” to terminate this selection.
Caps Lock Control
SS
SS
SS
“Caps Lock Off” State “Caps Lock On” State
Auto Detect (PC/AT, PS/2, Keyboard Replacement and DOS/V Machines only)
0
1
2
Caps Lock Release Control
SS
SS
“Caps Lock On, Caps Off” “Caps Lock On, Shift Off”
0
1
The function of “Caps Lock Control” and “Key Pad Emulation” are only available for IBM PC/AT, PS/VP, PS/2 series personal computers and compatible machines.
While selecting the other host interfaces, these selections don’t perform the above functions for you.
Please check the actual Caps Lock state in use while software application is running. If the Caps Lock state is off, select “Caps Lock Off” state, then FuzzyScan will
perform normal data transmission. If the Caps Lock state is on, select “Caps Lock On” state. Select “Auto Detect”, FuzzyScan will perform special transmission
handshaking without changing the status of Caps Lock switch.
31
Configure Your FuzzyScan
Keyboard Interface Control
♦ Delay Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Intermessage Delay
SS
MS
Parameter Selection
None 1-99 (x5) msec.
Option Code
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Intercharacter Delay
SS
MS
None 1-99 (x5) msec.
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Programming Manual
FuzzyScan
Interfunction Delay
SS
MS
None 1-99 (x5) msec.
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Intermessage Delay is a time delay between messages output by FuzzyScan. Increasing this delay will help host applications process the incoming data on time.
Intercharacter Delay is a time delay between data characters output by FuzzyScan. These two parameters are used to synchronize data communication when : 1) the data
transmission speed is too fast, characters may be skipped; 2) multitasking operation system or host computers in a network may slow down the keyboard handling; 3)
various notebook or desktop PC systems require different timing parameter settings. Please always add one extra unit as safety margin when adjusting these two
parameters.
Interfunction Delay is a time delay between the transmission of each segment of the message string.
32
Configure Your FuzzyScan
Keyboard Interface Control
♦ Emulation Setting & Upper/Lower Case Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Function Key Emulation
SS
SS
Parameter Selection
Enable ASCII 00-31 code as keyboard function code output Ctrl-Output
Option Code
0
1
Programming Manual
FuzzyScan
Refer to Appendix – Keyboard Function Code Table for details.
Key Pad Emulation
SS
SS
Disable key pad emulation Enable numeric output as key pad (Num Lock On) output
0
1
Upper/Lower Case
SS
SS
SS
SS
Normal case (neglect the upper/lower case control) Inverse case (change all characters output to inverse case)
Upper case (force all characters output as upper case)
Lower case (force all characters output as lower case)
0
1
2
3
33
Configure Your FuzzyScan
Serial Interface Control
♦ Record Suffix, Preamble ,Postamble Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
STX/ETX Control
SS
SS
Parameter Selection
Option Code
Disable STX/ETX transmission Enable STX/ETX transmission
0
1
Programming Manual
FuzzyScan
STX/ETX are two characters used to indicate the starting and ending of the total
data frame transmitted via serial interface.
Record Suffix
SS
SS
SS
SS
SS
SS
MS
None
CR (0DH) LF (0AH)
CRLF (0D0AH)
TAB (09H)
SPACE (20H)
User defined character (1 character)
Preamble
SS
MS
None 1-15 characters
0
1
2
3
4
5
6, (00-7F)
FIN
[00-7F], [FIN]
Maximum 15-character input; scan “FIN” to terminate this selection.
Postamble
SS
MS
None 1-15 characters
FIN
[00-7F], [FIN]
Maximum 15-character input; scan “FIN” to terminate this selection.
Serial Interface Message String (RS232, USB COM) :
STX
Preamble
Data Length
Prefix Symbol ID
Scanned Data
Suffix Symbol ID
Postamble
ETX
Record Suffix
1 character
1-15 characters
2-3 digits
1 or 2 characters
Variable length
1 or 2 characters
1-15 characters
1 character
1 character
34
Configure Your FuzzyScan
Serial Interface Control
♦ Delay Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Intermessage Delay
SS
MS
Parameter Selection
None 1-99 (x5) msec.
Option Code
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Intercharacter Delay
SS
MS
None 1-99 (x5) msec.
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Programming Manual
FuzzyScan
Interfunction Delay
SS
MS
None 1-99 (x5) msec.
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Intermessage Delay is a time delay between messages output by FuzzyScan. Increasing this delay will help host applications process the incoming data on time.
Intercharacter Delay is a time delay between data characters output by FuzzyScan. These two parameters are used to synchronize data communication when : 1) the data
transmission speed is too fast, characters may be skipped; 2) multitasking operation system or host computers in a network may slow down the keyboard handling; 3)
various notebook or desktop PC systems require different timing parameter settings. Please always add one extra unit as safety margin when adjusting these two
parameters.
Interfunction Delay is a time delay between the transmission of each segment of the message string.
35
Configure Your FuzzyScan
Serial Interface Control
♦ Protocol, ACK/NAK Setting ♦
Programming Manual
FuzzyScan
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Handshaking Protocol
SS
SS
SS
SS
None (free running mode) RTS/CTS (hardware handshaking)
ACK/NAK (software handshaking)
Xon/Xoff (software handshaking)
NAK Retry Count
SS
SS
3 times 0~255 times
ACK Indication
SS
SS
SS
SS
Disable ACK Time-out Indication
Enable ACK Time-out Indication Disable ACK Indication Enable ACK Indication
Option Code
0
1
2
3
FIN
(3 digits)
0
1
2
3
USB COM doesn’t support RTS/CTS handshaking protocol.
When the ACK/NAK Software Handshaking option is selected, the FuzzyScan waits for an ACK (acknowledge) or NAK (not acknowledge) from the host computer after
each data transmission. If the NAK is received, FuzzyScan will re-send the data until receiving ACK.’
NAK Retry Count
After transmitting data, the scanner expects a NAK response from the host up to the preset “Serial Response Time-out”. If the scanner doesn’t get a response, the scanner
will issue an error indication and discard the data. When a NAK is received, the scanner transmits the same data again and waits for either an ACK or NAK. The scanner
issues an error indication and discards the data under following two conditions:
1) After preset NAK retry counts is received within the preset serial response time-out.
2) If the preset time-out is up but the preset NAK retry counts haven’t come to the end.
The default retry counts are three times. If you program “0 time”, the scanner won’t resend the data to the host when the scanner receives a NAK. The scanner will discard
the data. If you program “255 times”, the scanner can receive unlimited NAKs from the host within the pre-set serial response time-out.
This function is not available for batch mode. When you enable this function in on-line mode, the out-of-range function will be disable automatically.
ACK Indication:
Disable: There’s neither LED nor beeping indication for this setting.
Enable: There’s a specific LED and beeping indication for this setting.
36
Configure Your FuzzyScan
Serial Interface Control
♦Time Out Setting, Baud Rate, Data Frame ♦
Programming Manual
FuzzyScan
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
Serial Response Time-out
SS
SS
SS
SS
SS
SS
None
200 mseconds
500 mseconds 800 mseconds
1 second
2 seconds
3 seconds
4 seconds
5 seconds
8 seconds
10 seconds
15 seconds
0
1
2
3
4
5
6
7
8
9
A
B
Baud Rate (BPS)
SS
SS
SS
SS
38.4K BPS
19.2K BPS
9600 BPS 4800 BPS
2400 BPS
1200 BPS
57.6K BPS
115.2K BPS
0
1
2
3
4
5
8
9
Data Frame
SS
SS
SS
SS
SS
SS
SS
SS
8, None, 1 8, Odd, 1
8, Even, 1
8, Space, 1
8, Mark, 1
8, None, 2
7, Odd, 1
7, Even, 1
7, Space, 1
7, Mark, 1
7, None, 2
7, Odd, 2
7, Even, 2
7, Space, 2
7, Mark, 2
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
When the RTS/CTS Hardware Handshaking option is selected, the RTS (request to send) and CTS (clear to send) signals will be issued before normal data
communication. This option is very helpful to ensure the reliability of data communication.
The Serial Response Time-out is a pre-defined delay time for FuzzyScan to wait for handshaking, acknowledgment or non-acknowledgment from the host computer.
37
Configure Your FuzzyScan
Wand/Laser Emulation Control
♦ Output Polarity, Signal State, Margin/Module Time, etc. ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Output Polarity
SS
SS
Parameter Selection
Option Code
High level (5Vdc) on Bar (low level on Space) Low level (0Vdc) on Bar (high level on Space)
0
1
Determine the output voltage level for both bar and space.
Initial Signal State
SS
SS
High Level (5Vdc) Low Level (0Vdc)
0
1
Programming Manual
FuzzyScan
Determine the initial state of output voltage level.
Margin Time
SS
SS
SS
SS
10 msec.
15 msec.
20 msec. 25 msec.
30 msec.
50 msec.
100 msec.
Delay time before data transmission
0
1
2
3
4
5
6
Module Time
SS
SS
SS
Extremely short
Short
Medium Long
0
1
2
3
Narrow/Wide Ratio
SS
SS
SS
1:2 1:2.5
1:3
0
1
2
Code 39/Code 128 Emulation
SS
SS
SS
SS
SS
Disable standard Code 39 emulation Enable standard Code 39 skip emulation
Enable standard Code 39 replace emulation
Enable Full ASCII Code 39 emulation
Enable Code 128 emulation
0
1
2
3
4
Time base of minimum narrow bar
[ Code 39 Skip] : When this option is selected, all scanned data will be translated as Standard Code 39 wand/laser emulation output. If any lower case characters are read,
they will be translated to upper case characters. Any other characters that are not available in Code 39 symbology set will be skipped.
[ Code 39 Replace] : Any character not normally available in the standard Code 39 symbology set, will be translated as Space.
38
Configure Your FuzzyScan
Operation Control
♦ Operation Mode Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Operation Mode
SS
SS
SS
SS
SS
Low Power mode
Trigger mode Presentation mode
Alternative mode
Flash mode
Presentation Control
SS
SS
SS
Presentation mode Flash mode
Force mode
Force mode
Toggle mode
Diagnostic mode
Level mode
L680/L780 laser imagers don’t support:
Flash/ Force/ Toggle/ Diagnostic mode.
Option Code
0
1
2
3
4
5
6
7
8
0
1
2
Programming Manual
FuzzyScan
L680/L780 laser imagers don’t support this function.
Low Power Mode (Low Power Triggering) The scanner goes into idle state after scanning the bar code. You must press the trigger to wake up the scanner for operation.
It is very helpful for mobile data collection and application, which are concerned with power saving.
Trigger Mode (External Triggering) The scanner goes into standby state after scanning the bar code. You must press the trigger to turn on the light source of the scanner
before scanning the bar code.
Presentation Mode (Auto Detection) Presentation mode uses ambient light to detect the bar codes. The light source is off until the scanner detects an image which is
similar to a barcode. Then the light source turns on automatically to read the bar code. If the light level in the room is not high enough, Presentation Mode may not work
properly. You can choose different level of “Presentation Sensitivity” to meet your application (Please refer to the setting of “Presentation Sensitivity”).
Alternative Mode (Periodic Power Off) The scanner keeps the light source of the scanner turned on till the pre-defined light source on time is up. After the scanner turns
off the light source, you must press the trigger to turn on the light source again. After each good read, the timer counter of “Light Source on Time” is reset. You do not have
to press the trigger frequently, it is very convenient for multiple scanning.
Flash Mode (Pulse Driven Reading) The scanner flashes the light source of the scanner without using the trigger. If the scanner detects an image which is similar to a bar
code, the scanner forces on the light source automatically and scans the bar code. Flash Duty Cycle adjustment can change the frequency of the blinking.
Force Mode (Continued Power On) The light source of the scanner is forced on for continued operation without pressing the trigger switch. This mode is convenient for
high speed bar code reading.
Toggle Mode (Repeat Reading) The toggle mode is very similar to the Alternative Mode but without the pre-defined light source on time concern. You must press the
trigger to turn on the light source of the scanner to scan. The scanner keeps the light source turned on until you press the trigger again.
Diagnostic Mode (Test Reading) This operation mode is specifically designed for diagnostic purposes. When this operation mode is selected, the light source of the
scanner is force on without regard for other programmable parameters, such as reread delay, redundancy, and so forth.
Level Mode (Auto Power Off) When this operation mode is selected, the scanner continues to turn on the light source of the scanner before a good read or pre-defined
“Light Source on Time”. If the scanner decodes a bar code successfully, it turns off the light source immediately. After the scanner turns off the light source, you must press
the trigger to turn on the light source again. If there is no scanning operation performed during the pre-defined light source on time, the scanner enters the idle state after
the pre-defined light source on time is up.
Presentation Control When the scanner is placed on SmartStand, the scanner will be switched from hand-held scanning to hands free scanning automatically. Three
hands scanning modes are available. You are recommended to use flash mode or force mode while under insufficient ambient light.
Only Low power mode, Trigger mode, Presentation mode and Level mode are available for FuzzyScan Laser model.
39
Configure Your FuzzyScan
Operation Control
♦ Buzzer, Indicator, Vibrator, Inverse Reading ♦
Programming Manual
FuzzyScan
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Buzzer Tone Adjust
SS
SS
SS
SS
SS
SS
SS
Buzzer tone – mute
Buzzer tone – low
Buzzer tone – medium Buzzer tone – high
Buzzer tone - extremely high
Power-on beep No power-on beep
0
1
2
3
4
5
6
Power On Indicator
SS
SS
SS
Disable (LED off)
LED steady on LED flash
0
1
2
Good Read Indicator
SS
SS
Disable
Enable 0
1
SS
SS
Disable
Enable 0
1
Vibrator Control
Parameter Selection
Option Code
Optional function, only available for vibrator model.
Inverse Reading
SS
SS
Disable Enable
0
1
40
Configure Your FuzzyScan
Operation Control
♦ Dollar Sign, Redundancy, Scan Rate Control♦
♦
Programming Manual
FuzzyScan
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Dollar Sign Control
SS
SS
SS
SS
SS
Dollar sign output as “ $ “ Dollar sign output as “ “
Dollar sign output as “ € “
Dollar sign output as “ £ “
Dollar sign output as “ ¢ “
0
1
2
3
4
Redundancy
SS
SS
SS
SS
SS
SS
None
Level 1 Level 2
Level 3
Level 4
Level 5
To prevent potential miss reading.
0
1
2
3
4
5
Scan Rate Control
SS
SS
Dynamic Fixed
0
1
¥
Option Code
The Redundancy is the number of times the same bar code label has to be decoded before it is transmitted.
Scan Rate Control: The scanner will have better motion tolerance when you select “Fixed” scan rate. It’s suitable for application which needs higher motion tolerance on
the move. But this may impact to the reading distance.
41
Configure Your FuzzyScan
Operation Control
♦ Flash Duty Cycle, Delay Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Flash Duty Cycle
SS
SS
SS
SS
Parameter Selection
1/2 duty cycle 2/3 duty cycle
3/4 duty cycle
4/5 duty cycle
Option Code
0
1
2
3
Programming Manual
FuzzyScan
L680/L780 laser imagers don’t support this function.
Reread Delay
(Double Scan Verification)
SS
SS
SS
SS
SS
SS
Disable
Immediate time out Short time out
Medium time out
Long time out
Force verification
0
1
2
3
4
5
Good Read Delay
SS
SS
SS
SS
SS
SS
SS
None 200 msec.
500 msec.
1 sec.
1.5 sec.
2 sec.
3 sec.
0
1
2
3
4
5
6
The Flash Duty Cycle is designed to control the flashing frequency of the light source.
The Reread Delay (Double Scan Verification) is designed to inhibit FuzzyScan from reading the same bar code label twice in pre-defined short duration. Force Verification
will not allow reading of the same bar code twice.
This Good Read Delay is the minimum amount of time before the imager can read another bar code.
42
Configure Your FuzzyScan
Operation Control
♦ Time-out Setting, Good Read Duration ♦
Programming Manual
FuzzyScan
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
Light Source On Time
SS
SS
SS
SS
Short Medium
Long
Extremely long
0
1
2
3
Hands Free Time-out
SS
SS
SS
SS
SS
Short Medium
Long
Extremely long
Disable
0
1
2
3
4
Good Read Duration
SS
SS
SS
SS
SS
Short
Medium Long
Extremely long
Extremely short
0
1
2
3
4
Time Delay to Low Power Mode
SS
SS
SS
SS
SS
SS
1 sec
3 secs
5 secs
7 secs
9 secs
Immediate 0
1
2
3
4
5
The Light Source On Time is a pre-defined light source time out counter for Alternative Mode, Presentation Mode and Level Mode. The scanner keeps the light source on
till the pre-defined light source on time is up. You can adjust this parameter to meet your own application requirement.
The Presentation Mode, Force Mode and Flash Mode are referred to as “hands free” mode. The hands free mode will be automatically changed to manual trigger mode
when you press the trigger. You can remain the scanner in manual trigger mode by setting the Hands Free Time-Out. Once the time-out duration is up (if there’s no any
trigger operation), the imager will revert to the original hands free mode.
The Time Delay to Low Power Mode sets the time for scanner to enter low power mode after any scanning activity. This setting is only available for the scanner is in low
power mode.
43
Configure Your FuzzyScan
Operation Control
♦ Presentation Scanning Setting , Trigger Control♦
♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
SmartStand Power Off Timeout
SS
SS
SS
Parameter Selection
Option Code
3 mins 5 mins
10 mins
0
1
2
Programming Manual
FuzzyScan
Only available for FuuzzyScan Laser model
Presentation Auto-sense
SS
SS
Disable
Enable 0
1
Presentation Sensitivity
SS
SS
SS
SS
SS
Level 1
Level 2
Level 3
Level 4
Level 5 Trigger Control
SS
SS
SS
Enable left trigger, disable right trigger
Enable right trigger, disable left trigger
Enable left and right triggers Level 6
Level 7
0
1
2
3
4
5
6
0
1
2
Only available for FuzzyScan F460/F468
The SmartStand Power Off Timeout is a pre-defined duration for scanner’s light source on time when the scanner is placed on SmartStand. While the scanner is placed on
SmartStand, the scanner’s will be switched from hand-held scanning to presentation scanning and the light source will be forced on automatically. The light source will be
off when the pre-defined duration is up.
When enable the Presentation Auto-sense, the scanner can be switched between hands free scanning and hand-held scanning automatically when working with the
SmartStand.
The presentation sensitivity is used to configure the sensitivity level when the scanner is set as presentation mode. The higher lever means higher sensitivity for detecting
the barcode.
44
Configure Your FuzzyScan
Operation Control
♦ Laser Aiming Control♦
♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Laser Aiming Control
SS
SS
Parameter Selection
Disable
Enable
0
◆
1
Only available for L series laser imaging scanner.
Programming Manual
You can disable or enable laser aiming line when you can PDF barcode.
FuzzyScan
Option Code
45
Configure Your FuzzyScan
Condensed DataWizard
♦ Preamble, Postamble, Data Length & Symbol ID Trans. ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Preamble
SS
MS
Parameter Selection
None 1-15 characters
Option Code
FIN
[00-7F], [FIN]
Maximum 15-character input; scan “FIN” to terminate this selection.
Postamble
SS
MS
None 1-15 characters
FIN
[00-7F], [FIN]
Maximum 15-character input; scan “FIN” to terminate this selection.
Programming Manual
FuzzyScan
Data Length Transmission
SS
SS
Disable Enable 2 digits data length transmission
0
1
If data length exceeds 99, 3-digit data length will be transmitted.
Symbology ID Transmission
SS
SS
SS
SS
SS
SS
SS
Disable symbology ID transmission Enable prefix symbology ID transmission
Enable suffix symbology ID transmission
Enable both prefix and suffix symbology ID transmission
Enable prefix AIM symbology ID transmission
Enable suffix AIM symbology ID transmission
Enable both prefix and suffix AIM symbology ID transmission
0
1
2
3
4
5
6
DataWizard is the most powerful, Artificial-Intelligence based data editing expert system provided specially for the FuzzyScan family bar code readers. Through DataWizard,
you can process the scanned data prior the transmissions in many ways as: Insert, Delete, Match, Verify, Replace, Reorganize, and Repeat Transmission. It will help
you to arrange the transmission of scanned data to any specific format without software modification.
Due to the resources used by this system, Full-feature DataWizard is only supported by PowerTool. Through the PowerTool, all settings and configurations can be done
on-screen, under Windows 95/98/NT/2000/XP environment.
A Condensed Version DataWizard is provided by each FuzzyScan series. Through this menu, the condensed DataWizard can be utilized via bar code menu readings with
ease.
Please note that all “Character” input should be referred to the ASCII/HEX Table listed in Appendix to find matched HEX value.
If you have any problem to use DataWizard, please refer to following pages for details and consult your local FuzzyScan vendor or our web site for any assistance.
46
Configure Your FuzzyScan
Condensed DataWizard
♦ Data Formatter Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Formatter Control
SS
MS
MS
1st Insertion
SS
DS
Parameter Selection
Option Code
2nd Option Code
Disable Select one bar code symbology
Select all bar code symbologies
FIN
(2 digits)
00
automatic termination
automatic termination
Disable Enable
FIN
(2 digits)
[1-3 characters], [FIN]
2-digits identified position; max. 3 insertion characters
Programming Manual
FuzzyScan
2nd Insertion
SS
DS
Disable Enable
FIN
(2 digits)
2-digits identified position; max. 3 insertion characters
3rd Insertion
SS
DS
Disable Enable
SS
DS
Disable Enable
[1-3 characters], [FIN]
position
FIN
(2 digits)
2-digits identified position; max. 3 insertion characters
[1-3 characters], [FIN]
position
FIN
(2 digits)
2-digits identified position; max. 3 insertion characters
4th Insertion
position
[1-3 characters], [FIN]
position
The Data Formatter is used to edit the scanned raw data prior to transmitting the data to the host computers or terminals. It allows you to select desired bar code
symbologies for formatter control, and provides Multiple Position Insertion and Multiple Character Insertion (max three characters) in the identified position.
While the Data Formatter is enabled, it arranges only scanned data without Preamble, Postamble, STX, ETX, Data Length, Prefix/Suffix Symbology ID or Record Suffix.
All of the above programmable parameters perform the same function depending on your setting.
Regarding the “Bar Code Selection” and “Position Calculation” of data formatter, please refer to page 45 for details.
Please note that all “Character” input should be referred to the ASCII/HEX Table listed in Appendix to find matched HEX value.
47
Configure Your FuzzyScan
Condensed DataWizard
♦ Data Verifier Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Verifier Control
SS
MS
MS
SS
DS
Identified Data Length
Parameter Selection
Option Code
2nd Option Code
Disable Select one bar code symbology
Select all bar code symbologies
FIN
(2 digits)
00
automatic termination
automatic termination
Disable Enable
FIN
(2 digits)
Determine the identified data length for verification.
Programming Manual
FuzzyScan
1st Identified Character
SS
DS
Disable Enable
FIN
(2 digits)
2-digits checking position; 1 identified character
2nd Identified Character
SS
DS
Disable Enable
3rd Identified Character
SS
DS
position
FIN
(2 digits)
2-digits checking position; 1 identified character
Disable Enable
[00-7F]
position
FIN
(2 digits)
2-digits checking position; 1 identified character
[00-7F]
[00-7F]
position
The Data Verifier is used to provide advanced verification for error-free scanning and to work as an Embedded Data Transmitting Filter.
All data must conform to the Identified Bar Code Symbologies, Identified Data Length, and one to three Identified Characters in the checking position. Otherwise, the
FuzzyScan will not transmit the data to the host computers or terminals, but will instead issue 3 long beeps for verification error and skip the scanned data.
The Data Verifier checks only scanned data without Preamble, Postamble, STX, ETX, Data Length, Prefix/Suffix Symbology ID or Record Suffix.
Regarding the “Bar Code Selection” and “Position Calculation” of Data Verifier, please refer to page 45 for details.
Please note that all “Character” input should be referred to the ASCII/HEX Table listed in Appendix to find matched HEX value.
48
Configure Your FuzzyScan
Condensed DataWizard
♦ Data Replacer Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Replacer Control
SS
MS
MS
1st Replacement
SS
DS
Parameter Selection
Option Code
2nd Option Code
Disable Select one bar code symbology
Select all bar code symbologies
FIN
(2 digits)
00
automatic termination
automatic termination
Disable Enable
FIN
(2 digits)
[00-7F]
2-digits identified position; 1 replacement character
Programming Manual
FuzzyScan
2nd Replacement
SS
DS
Disable Enable
FIN
(2 digits)
2-digits identified position; 1 replacement character
3rd Replacement
SS
DS
position
Disable Enable
position
FIN
(2 digits)
2-digits identified position; 1 replacement character
[00-7F]
[00-7F]
position
The Data Replacer is used to edit the scanned raw data prior to transmitting the data to the host computers or terminals. It allows you to select desired bar code
symbologies for replacer control, and provides Multiple Position Replacement in the identified position.
All data must conform to the Identified Bar Code Symbologies, and one to three Identified Characters in the identified position While the Data Replacer is enabled, it
arranges only scanned data without Preamble, Postamble, STX, ETX, Data Length, Prefix/Suffix Symbology ID or Record Suffix.
Regarding the “Bar Code Selection” and “Position Calculation” of Data Replacer, please refer to page 45 for details.
Please note that all “Character” input should be referred to the ASCII/HEX Table listed in Appendix to find matched HEX value.
49
Configure Your FuzzyScan
Condensed DataWizard
♦ Data Organizer Setting ♦
PROGRAM
Family Code Selection
P.C
Organizer Control
SS
MS
MS
SS
DS
1st Organization
Programming Manual
2nd Organization
FuzzyScan
F_DEFAULT
Include/Exclude Control
SS
DS
SS
DS
Parameter Selection
Option Code
2nd Option Code
Disable Select one bar code symbology
Select all bar code symbologies
FIN
(2 digits)
00
automatic termination
automatic termination
Disable Enable
FIN
(2 digits)
2-digits identified position;
Forward/backward data transmission setting
position
direction
Disable Enable
FIN
(2 digits)
2-digits identified position;
Forward/backward data transmission setting
position
direction
Transmitted data excluded the data of identified position Transmitted data included the data of identified position
0 (Forward) 1 (Backward)
0 (Forward) 1 (Backward)
0
1
The Data Organizer is used to edit the scanned raw data prior to transmitting the data to the host computers or terminals. It allows you to select desired bar code
symbologies for organizer control, and provides maximum two identified positions to send the data forward or backward. It also allows you to control the transmitted data
including or excluding the data of identification position. Please refer to the application example listed in page 45 for details.
While the Data Organizer is enabled, it arranges only scanned data without Preamble, Postamble, STX, ETX, Data Length, Prefix/Suffix Symbology ID or Record
Suffix.
Regarding the “Bar Code Selection” and “Position Calculation” of Data Organizer, please refer to page 45 for details.
Please note that all “Character” input should be referred to the ASCII/HEX Table.
50
Configure Your FuzzyScan
[Data Verifier, Data Replacer, Data Organizer]
Select a Bar Code Symbology
If there is a 11-character data string, please refer to the
following to calculate the actual position for identification.
Programming Manual
FuzzyScan
You can select one or all types of bar code symbologies to
use Condensed DataWizard for advanced transmission
arrangement. If you scan “00” to select all types, the
FuzzyScan will arrange all incoming data to meet your
pre-defined format. If you want to select only one type bar
code, please select one of the option code listed below.
Code 128 : 01
EAN-8 : 05
Code 93 : 09
UCC/EAN 128 : 31
EAN-8 with 2 supple : 35
Code 11 : 10
UPC-A : 02
EAN-8 with 5 supple.: 45
MSI/Plessey : 11
UPC-A with 2 supple.: 32
Codabar/NW-7 : 06
UK/Plessey : 12
UPC-A with 5 supple.: 42
Code 39 : 07
Telepen : 13
UPC-E : 03
Code 32 : 37
GS1 Data Bar : 14
UPC-E with 2 supple.: 33
Trioptic Code 39: 47
IATA : 15
UPC-E with 5 supple.: 43
Matrix 2 of 5 : 38
Coupon Code : 16
EAN-13 : 04
Interleaved 2 of 5 : 48
PDF417/Micro PDF417: 22
EAN-13 with 2 supple. : 34
China Postal Code : 58
Codablock: 23
EAN-13 with 5 supple. : 44
German Postal Code : 68
Korea Post Code: 26
X
X
X
X
X
X
X
X
X
X
X
00
01
02
03
04
05
06
07
08
09
10
Application Example
If your bar code label is a 16-digit Interleaved 2 of 5 which
includes the information of 6-digit date code, 6-digit serial
number and 4-digit unit price, you want the FuzzyScan do
the following for you without software modification:
Apply only Interleaved 2 of 5 to the condensed
DataWizard.
Check bar code is actually with 16-digit length.
Allow bar code output whose date code is leading with
“9”.
Position Calculation
Three outputs with “TAB” suffix.
[Data Formatter]
The date code output should skip “9” and replaced it by
“A”.
If there is a 5-character input data string, refer to the following
to calculate the actual position for insertion:
X
00
X
01
X
02
X
03
The serial number output should be led with “SN”.
X
04
The unit price output should be skipped the first 2
digits.
05
Test Bar Code : 9 8 1 0 2 5 1 2 3 4 5 6 9 8 7 6
Actual Output : A81025[TAB]SN123456[TAB]76[TAB]
51
Configure Your FuzzyScan
Programming Procedure
[Data Verifier]
[Data Replacer]
Scan “Program” to enter the programming mode.
Scan “Replacer Control” and set bar code symbology
to “48”.
Scan “Verifier Control” and set bar code symbology to “48”
(Interleaved 2 of 5).
Scan “1st Replacement” and set the identified position
to “00”, then replaced character to “41” (Hex Code of
A).
Programming Manual
FuzzyScan
Scan “Identified Data Length” and set the length to “16”.
Scan “1st Identified Character” and set the identified
position to “00”, then set the identified character to “39”
(Hex Code of 9).
[Data Organizer]
[Data Formatter]
Scan “Organizer Control” and set bar code symbology
to “48”.
Scan “Formatter Control” and set bar code symbology to
“48”.
Scan “1st Organization” and set the identified position
to “16”, then set the data transmission to “0” (forward).
Scan 1st Insertion” and set the identified position to “06”,
then inserted characters to “09” (Hex Code of TAB), “53”
(Hex Code of S), “4E” (Hex Code of N).
Scan “2nd Organization” and set the identified position
to “17”, then set the data transmission to “1”
(backward).
Scan “2nd Insertion” and set the identified position to “12”,
then inserted character to “09”. In the final, you must scan
“FIN” (Finish) code to terminate this selection.
Scan “END” (Exit) to terminate the programming.
[Important Notice]
Scan “3rd Insertion” and set the identified position to “16”,
Please note that Condensed DataWizard will follow the
preset working flow as below:
then inserted character to “09”. In the final, you must scan
“FIN” (Finish) code to terminate this selection.
Verifier
Formatter Replacer
Organizer
So when you set the identified position in Data Organizer,
you must consider the inserted data which you already set
via Data Formatter.
52
Appendix
Symbology ID Table
Each AIM Code Identifier contains the three-character string ]cm where:
] = Flag Character
c = Code Character
m = Modifier Character
Cino ID
Code Family
Primary Format
AIM ID
Code
Code
Modified
Character
Character
Character
UPC-A
UPC-A with 2 supple.
A
UPC-A with 5 supple.
UPC
E
UPC-E
UPC-E with 2 supple.
E
Programming Manual
UPC-E with 5 supple.
FuzzyScan
Cino ID
Code Family
m
EAN/JAN-8
1
EAN/JAN-8 with 2 supple.
2
EAN/JAN-8 with 5 supple.
m
EAN/JAN
Codabar
Code 25
IATA
UCC Coupon
Code 128
B
GS1-128
C
Codabar/NW-7
D
C
F
Code
Code
Modified
Character
Character
Character
4
N
E
1
EAN/JAN-13 with 2 supple.
EAN/JAN-13 with 5 supple.
1
2
EAN/JAN-13
2
Example: A UPC-A bar code 012345678950 with 2 supplement 12 is
transmitted as ]E0012345678950]E112
Code 128
Primary Format
AIM ID
m
F
E
1
2
Example: A EAN/JAN-8 bar code 49123562 with 5 supplement 12345 is
transmitted as ]E449123562]E212345
m
Code 93
Code 93
1
Code 11
Code 11
m
MSI/Plessey
MSI/Plessey
H
G
m
P
H
m
R
M
m
Standard/Industrial 2 of 5
I
S
0
UK/Plessey
UK/Plessey
S
P
0
Matrix 2 of 5
K
X
0
Telepen
Telepen
T
B
m
Interleaved 2 of 5
J
I
m
GS1 DataBar
GS1 Databar
0
X
0
Composite Code
e
L
Composite
X
China Postal Code
Code 39
G
A
m
German Postal Code
M
I
3
Code 39 Trioptic
W
X
0
IATA
O
R
m
UCC Coupon Code
Z
Example : A UPC-A 512345678900 + GS1-128 81010123451297 bar
code is transmitted as]E0512345678900]C181010123451297
Example: A EAN-13 9923456789019 + GS1-128 81010123451297 bar
code is transmitted as ]E09923456789019]C181010123451297
Code 39
Code 32
G
A
0
PDF417
PDF417/Micro PDF417
V
L
0
Codablock
Codablock F
Y
O
0
Korea Post
Korea Post Code
a
X
0
Remark: Above examples are given for the transmission of AIM ID.
53
Appendix
Programming Manual
FuzzyScan
Keyboard Function Code Table
No.
ANSI
ASCII
00
NUL
00H
01
SOH
02
Key Function
No.
ANSI
ASCII
Key Function
RESERVED
16
DLE
10H
F7
01H
CTRL (Left)
17
DC1
11H
F8
STX
02H
ALT (Left)
18
DC2
12H
F9
03
ETX
03H
SHIFT
19
DC3
13H
F10
04
EOT
04H
CAPS LOCK
20
DC4
14H
F11
05
ENQ
05H
NUM LOCK
21
NAK
15H
F12
06
ACK
06H
ESC
22
SYN
16H
INS (Insert) (Edit)
07
BEL
07H
F1
23
ETB
17H
DEL (Delete) (Edit)
08
BS
08H
BACK SPACE
24
CAN
18H
HOME (Edit)
09
HT
09H
TAB
25
EM
19H
END (Edit)
10
LF
0AH
F2
26
SUB
1AH
PAGE UP (Edit)
11
VT
0BH
F3
27
ESC
1BH
PAGE DOWN (Edit)
12
FF
0CH
F4
28
FS
1CH
UP (Edit)
13
CR
0DH
ENTER (CR)
29
GS
1DH
DOWN (Edit)
14
SO
0EH
F5
30
RS
1EH
LEFT (Edit)
15
SI
0FH
F6
31
US
1FH
RIGHT (Edit)
To emulate the keyboard function key input for user definable parameters, user must configure actual content using the
Reserved ASCII 0 – 31 characters, and also Enable the “Function Key Emulation”. Otherwise, the Ctrl output will be done
by the scanner. Please refer to the above Keyboard Function Code Table which is for IBM PC/XT/AT, PS/2, PS/VP,
COMPAQ PC, HP Vectra PC, Notebook PC, APPLE and PowerMac, and WYSE PC Enhanced or fully compatible machines.
54
Appendix
ASCII Input Shortcut
To configure the user definable parameters of FuzzyScan via
programming menu, FuzzyScan will ask you to scan your
desired ASCII value in HEX form. You have to refer to the
“HEX/ASCII Table” for details.
HEX/ASCII Reference Table
H
0
1
2
3
4
5
6
7
0
NUL
DLE
SPACE
0
@
P
`
p
Example:
1
SOH
DC1
!
1
A
Q
a
q
If you want the scanned data output leading with a Dollar
Sign, you have to set the “Preamble” to “$”. The configuration
procedure is listed below for reference.
2
STX
DC2
"
2
B
R
b
r
3
ETX
DC3
#
3
C
S
c
s
4
EOT
DC4
$
4
D
T
d
t
5
ENQ
NAK
%
5
E
U
e
u
6
ACK
SYN
&
6
F
V
f
v
7
BEL
ETB
'
7
G
W
g
w
8
BS
CAN
(
8
H
X
h
x
9
HT
EM
)
9
I
Y
i
y
A
LF
SUB
*
:
J
Z
j
z
B
VT
ESC
+
;
K
[
k
{
C
FF
FS
,
<
L
\
l
|
D
CR
GS
-
=
M
]
m
}
Scan the system command – FIN (Finish) to terminate
Preamble setting.
E
SO
RS
.
>
N
^
n
~
F
SI
US
/
?
O
_
o
DEL
Scan the system command – End to exit the programming
mode for normal operation.
Example : ASCII “A” → HEX “41”; ASCII “a” → “61”
L
Scan the system command – PROGRAM listed on page
3-24 to enter programming mode.
Scan family code – PREAMBLE to select this family.
Programming Manual
FuzzyScan
Refer to the Hex/ASCII Table, you will find the HEX value
of “$” is 24.
Scan the option code – 2 listed on the fold out back cover.
Scan the option code – 4 listed on the fold out back cover.
: High Byte of HEX Value
: Low Byte of HEX Value
55
Appendix
Host Interface Quick Set
RS232 Serial
PS/2 (DOS/V) KBW Standard Mode
USB HID Standard Mode
Keyboard Replacement
PS/2 (DOS/V) KBW Turbo Mode
Programming Manual
FuzzyScan
USB HID Turbo Mode
USB Com Port Emulation
56
Appendix
Operation Mode Quick Set
Low Power (Low power trigger)
Force (Continued power on)
Alternative (Periodic power off)
Trigger (External triggering)
Toggle (Repeat reading)
Programming Manual
FuzzyScan
Flash (Pulse driven reading)
Presentation (Auto sensing)
Diagnostic (Test reading)
Level (Auto power off)
57
Appendix
Option Codes
0
8
4
C
1
9
5
D
Programming Manual
FuzzyScan
2
A
6
E
3
B
7
F
FIN (Finish)
END (Exit)
58
Appendix
System Commands
PROGRAM
(Enter Programming Mode)
System Information List
(SYSLIST)
Save User Default
FIN (Finish)
PowerTool Host Link
Programming Manual
FuzzyScan
User Default
END
(Exit Programming Mode)
Factory Default
Master Default
Factory Default: After scanning” Factory Default” command, all parameters will be returned to factory default value.
Master Default: After scanning “Master Default” command, the scanner will remain the pre-set parameters of Host Interface Selection, Keyboard Interface
Control (except Record Suffix; Preamble; Postamble), Serial Interface Control (except Record Suffix; Preamble; Postamble), and Wand/Laser Emulation
Control, the rest of parameters will be returned to default value.
User Default: After scanning” Save User Default” command, all current parameters will be stored to the flash memory. Once you change the parameter and
would like to return to previous setting, please scan “User Default”.
59
www.cino.com.tw
FuzzyScan Family Programming Manual
CINO GROUP
PC WORTH INT’L CO., LTD.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising