Quanmax KEEX-4030 User`s guide
KEEX-4030
Intel® Embedded Compact Extended Form Factor
with Intel® GM45/ ICH9M
User’s Guide
KEEX-4030 User’s Manual
I
Contact Info:
Quanmax Inc.
5F, No. 415, Ti-Ding Blvd. Sec. 2, NeiHu District,
Taipei, Taiwan 114
Tel: +886-2-2799-2789
Fax: +886-2-2799-7399
Visit our site at:
www.quanmax.com
© 2009 Quanmax Inc. All rights reserved.
The information in this user’s guide is provided for reference only. Quanmax does not assume any
liability arising out of the application or use of the information or products described herein. This user’s
guide may contain or reference information and products protected by copyrights or patents and does
not convey any license under the patent rights of Quanmax, nor the rights of others.
Quanmax is a registered trademark of Quanmax. All trademarks, registered trademarks, and trade
names used in this user’s guide are the property of their respective owners. All rights reserved. This
user’s guide contains information proprietary to Quanmax. Customers may reprint and use this user’s
guide in other publications. Customers may alter this user’s guide and publish it only after they remove
the Quanmax name, cover, and logo.
Quanmax reserves the right to make changes without notice in product or component design as
warranted by evolution in user needs or progress in engineering or manufacturing technology.
Changes which affect the operation of the unit will be documented in the next revision of this user’s
guide.
Revision
Date
Edited by
Changes
1.0
03/26/2009
SLee
Initial Release
1.1
04/15/2009
SLee
JP1 Setting Correction
1.2
08/21/2009
SLee
Update LVDS table
1.3
10/05/2009
SLee
Minor Correction, Delete iAMT Function
1.4
12/16/2009
SLee
Correct RS232/422/485 pin assignment
KEEX-4030 User’s Manual
II
Content
Content
Content....................................................................................................................... 3
Figures ....................................................................................................................... 4
Tables ......................................................................................................................... 5
Safety Instructions ...................................................................................................... 7
Before You Begin ...................................................................................... 7
When Working Inside a Computer ............................................................ 7
Preventing Electrostatic Discharge ........................................................... 8
Preface ..................................................................................................................... 10
How to Use This Guide........................................................................... 10
Unpacking .............................................................................................. 10
Regulatory Compliance Statements ....................................................... 10
Warranty Policy ...................................................................................... 11
Maintaining Your Computer .................................................................... 12
Chapter 1 Introduction ........................................................................................... 15
Overview ................................................................................................ 15
Product Specifications ............................................................................ 16
System Block Diagram ........................................................................... 17
Mechanical Dimensions.......................................................................... 18
Chapter 2 Hardware Settings ................................................................................ 19
Overview ................................................................................................ 19
Jumper Settings and Pin Definitions ....................................................... 20
Jumper Settings ......................................................................................... 21
Rear Panel Pin Assignments...................................................................... 22
Main Board Pin Assignments ..................................................................... 24
Chapter 3 System Installation ................................................................................ 30
Processor Installation ............................................................................. 30
Processor Handling .................................................................................... 30
Installing the CPU ...................................................................................... 30
Removing the CPU: ................................................................................... 31
Cooler Installation ................................................................................... 32
Memory Module Installation .................................................................... 33
Chapter 4 AMI BIOS Setup .................................................................................... 34
Overview ................................................................................................ 34
Main Menu.............................................................................................. 35
Advanced Menu ..................................................................................... 36
Boot Menu .............................................................................................. 40
Chipset Menu ......................................................................................... 41
Power Menu ........................................................................................... 43
Security Menu ........................................................................................ 44
Exit Menu ............................................................................................... 44
Chapter 5 Driver Installation .................................................................................. 46
KEEX-4030 User’s Manual
3
Figures
Figures
Figure 1 Block Diagram ..........................................
Figure 2 Mechanical Dimensions ...................................
Figure 3 Jumper Connector .......................................
Figure 4 Jumper and Connector Locations ............................
Figure 5 Disengage the socket actuator ..............................
Figure 6 CPU alignment in Micro-FCPGA Socket (Socket P) ...............
Figure 7 Secure the processor in the socket ...........................
Figure 8 Align the SO-DIMM Memory Module with the onboard socket ........
Figure 9 Press down on the SO-DIMM Memory Module to lock it in place ......
KEEX-4030 User’s Manual
4
17
18
19
20
30
31
31
33
33
Tables
Tables
Table 1 KEEX-4030 Specification ............................
Table 2 Jumper List ......................................
Table 3 JP1 Power Mode Selection ...........................
Table 4 JP2 Clear CMOS Selection ...........................
Table 5 JP3 Backlight & Panel Power Selection ..................
Table 6 JP4 Clear ME RTC Registers .........................
Table 7 JP5 Backlight Enable Selection ........................
Table 8 Rear Panel Connector Descriptions .....................
Table 9 DVI (DVI-I Connector) ...............................
Table 10 HDMI1 (HDMI1 connector) ..........................
Table 11 COM1 (RS-232/422/485 Port A DB-9 Connector) ..........
Table 12 LAN1 (10/100/1000 Ethernet RJ-45 Connector) ...........
Table 13 USB1 (USB2.0 Port 0, 1 Type A Connector) ..............
Table 14 Connector List ...................................
Table 15 ATX1, +12V Power Input Connector ....................
Table 16 CF1, CF Type II Connector ..........................
Table 17 CN1, Panel Backlight Wafer .........................
Table 18 CN2, Digital Input / Output Pin Header ..................
Table 19 CN3, HD Audio Box Header..........................
Table 20 CN4, LPC Box Header .............................
Table 21 COM2, RS-232 Port B Wafer .........................
Table 22 FAN1, CPU FAN Wafer .............................
Table 23 FP1, Front Panel 1 Pin Header .......................
Table 24 FP2, Front Panel 2 Pin Header .......................
Table 25 LVDS1, LVDS Panel Connector .......................
Table 26 SATA1, Serial ATA & HDD Power Connector ..............
Table 27 SATA2, Serial ATA Connector ........................
Table 28 USB2, USB2.0 Port 2, 3 Pin Header ...................
Table 29 USB3, USB2.0 Port 4, 5 Pin Header ...................
Table 30 KM1, Keyboard and mouse connector ..................
Table 31 BIOS Main Menu .................................
Table 32 IDE Device Setting Menu ...........................
Table 33 System Information ................................
Table 34 Advanced Menu ..................................
KEEX-4030 User’s Manual
5
16
21
21
21
21
21
21
22
22
23
23
23
23
24
24
24
25
25
26
26
26
26
27
27
27
28
28
28
29
29
35
35
36
36
Tables
Table 35 Super I/O Configuration .............................
Table 36 OnBoard Peripherals Configuration Settings .............
Table 38 iTPM Function ...................................
Table 39 Hardware Health Configuration .......................
Table 40 Boot Menu ......................................
Table 41 Chipset Menu ....................................
Table 42 Video Function Configuration .........................
Table 43 Power Menu .....................................
Table 44 Security Menu ...................................
Table 45 Exit Menu .......................................
KEEX-4030 User’s Manual
6
37
37
38
39
40
41
42
43
44
44
Safety Instructions
Safety Instructions
„ Before You Begin
Before handling the product, read the instructions and safety guidelines on the
following pages to prevent damage to the product and to ensure your own personal
safety. Refer to the “Advisories” section in the Preface for advisory conventions used
in this user’s guide, including the distinction between Warnings, Cautions, Important
Notes, and Notes.
„
„
Always use caution when handling/operating a computer. Only qualified,
experienced, authorized electronics service personnel should access the
interior of a computer. The power supplies produce high voltages and
energy hazards, which can cause bodily harm.
Use extreme caution when installing or removing components. Refer to the
installation instructions in this user’s guide for precautions and procedures.
If you have any questions, please contact Quanmax Post-Sales Technical
Support.
WARNING
High voltages are present inside the chassis when the unit’s power cord is
plugged into an electrical outlet. Turn off system power, turn off the power
supply, and then disconnect the power cord from its source before
removing the chassis cover. Turning off the system power switch does not
remove power to components.
„ When Working Inside a Computer
Before taking covers off a computer, perform the following steps:
1. Turn off the computer and any peripherals.
2. Disconnect the computer and peripherals from their power sources or
subsystems to prevent electric shock or system board damage. This does not
apply when hot swapping parts.
KEEX-4030 User’s Manual
7
Safety Instructions
3.
4.
Follow the guidelines provided in “Preventing Electrostatic Discharge” on the
following page.
Disconnect any telephone or telecommunications lines from the computer.
In addition, take note of these safety guidelines when appropriate:
„
„
To help avoid possible damage to system boards, wait five seconds after
turning off the computer before removing a component, removing a system
board, or disconnecting a peripheral device from the computer.
When you disconnect a cable, pull on its connector or on its strain-relief loop,
not on the cable itself. Some cables have a connector with locking tabs. If you
are disconnecting this type of cable, press in on the locking tabs before
disconnecting the cable. As you pull connectors apart, keep them evenly
aligned to avoid bending any connector pins. Also, before connecting a cable,
make sure both connectors are correctly oriented and aligned.
CAUTION
Do not attempt to service the system yourself except as explained in this
user’s guide. Follow installation and troubleshooting instructions closely.
„ Preventing Electrostatic Discharge
Static electricity can harm system boards. Perform service at an ESD workstation
and follow proper ESD procedure to reduce the risk of damage to components.
Quanmax strongly encourages you to follow proper ESD procedure, which can
include wrist straps and smocks, when servicing equipment.
You can also take the following steps to prevent damage from electrostatic
discharge (ESD):
„
„
When unpacking a static-sensitive component from its shipping carton, do not
remove the component’s antistatic packing material until you are ready to install
the component in a computer. Just before unwrapping the antistatic packaging,
be sure you are at an ESD workstation or grounded. This will discharge any
static electricity that may have built up in your body.
When transporting a sensitive component, first place it in an antistatic container
KEEX-4030 User’s Manual
8
Safety Instructions
„
„
„
or packaging.
Handle all sensitive components at an ESD workstation. If possible, use
antistatic floor pads and workbench pads.
Handle components and boards with care. Don’t touch the components or
contacts on a board. Hold a board by its edges or by its metal mounting bracket.
Do not handle or store system boards near strong electrostatic, electromagnetic,
magnetic, or radioactive fields.
KEEX-4030 User’s Manual
9
Preface
Preface
„ How to Use This Guide
This guide is designed to be used as step-by-step instructions for installation, and as
a reference for operation, troubleshooting, and upgrades.
NOTE
Driver downloads and additional information are available under
Downloads on our web site: www.quanmax.com.
„ Unpacking
When unpacking, follow these steps:
1.
2.
3.
After opening the box, save it and the packing material for possible future
shipment.
Remove all items from the box. If any items listed on the purchase order
are missing, notify Quanmax customer service immediately.
Inspect the product for damage. If there is damage, notify Quanmax
customer service immediately. Refer to “Warranty Policy” for the return
procedure.
„ Regulatory Compliance Statements
This section provides the FCC compliance statement for Class A devices.
FCC Compliance Statement for Class A Devices
The product(s) described in this user’s guide has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
KEEX-4030 User’s Manual
10
Preface
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the user’s guide, may cause harmful
interference to radio communications. Operation of this equipment in a residential
area (domestic environment) is likely to cause harmful interference, in which case
the user will be required to correct the interference (take adequate measures) at
their own expense.
Changes or modifications not expressly approved by Quanmax could void the user's
authority to operate the equipment.
NOTE
The assembler of a personal computer system may be required to test
the system and/or make necessary modifications if a system is found to
cause harmful interference or to be noncompliant with the appropriate
standards for its intended use.
„ Warranty Policy
Limited Warranty
Quanmax Inc.’s detailed Limited Warranty policy can be found under Support at
www.quanmax.com. Please consult your distributor for warranty verification.
The limited warranty is void if the product has been subjected to alteration, neglect,
misuse, or abuse; if any repairs have been attempted by anyone other than
Quanmax or its authorized agent; or if the failure is caused by accident, acts of God,
or other causes beyond the control of Quanmax or the manufacturer. Neglect,
misuse, and abuse shall include any installation, operation, or maintenance of the
product other than in accordance with the user’s guide.
No agent, dealer, distributor, service company, or other party is authorized to change,
modify, or extend the terms of this Limited Warranty in any manner whatsoever.
Quanmax reserves the right to make changes or improvements in any product
without incurring any obligation to similarly alter products previously purchased.
Return Procedure
For any Limited Warranty return, please contact Support at www.quanmax.com and
KEEX-4030 User’s Manual
11
Preface
login to obtain a Return Material Authorization (RMA) Number. If you do not have an
account, send an email to [email protected] to apply for one.
All product(s) returned to Quanmax for service or credit must be accompanied by a
Return Material Authorization (RMA) Number. Freight on all returned items must be
prepaid by the customer who is responsible for any loss or damage caused by
common carrier in transit. Returns for Warranty must include a Failure Report for
each unit, by serial number(s), as well as a copy of the original invoice showing the
date of purchase.
To reduce risk of damage, returns of product must be in a Quanmax shipping
container. If the original container has been lost or damaged, new shipping
containers may be obtained from Quanmax Customer Service at a nominal cost.
Quanmax owns all parts removed from repaired products. Quanmax uses new and
reconditioned parts made by various manufacturers in performing warranty repairs
and building replacement products. If Quanmax repairs or replaces a product, its
warranty term is not extended.
Shipments not in compliance with this Limited Warranty Return Policy will not be
accepted by Quanmax.
Limitation of Liability
In no event shall Quanmax be liable for any defect in hardware, software, loss, or
inadequacy of data of any kind, or for any direct, indirect, incidental, or
consequential damages in connection with or arising out of the performance or use
of any product furnished hereunder. Quanmax’s liability shall in no event exceed the
purchase price of the product purchased hereunder. The foregoing limitation of
liability shall be equally applicable to any service provided by Quanmax or its
authorized agent.
„ Maintaining Your Computer
Environmental Factors
„
Temperature
The ambient temperature within an enclosure may be greater than room
ambient temperature. Installation in an enclosure should be such that the
amount of air flow required for safe operation is not compromised.
Consideration should be given to the maximum rated ambient temperature.
Overheating can cause a variety of problems, including premature aging and
failure of chips or mechanical failure of devices.
KEEX-4030 User’s Manual
12
Preface
If the system has been exposed to abnormally cold temperatures, allow a
two-hour warm-up period to bring it up to normal operating temperature before
turning it on. Failure to do so may cause damage to internal components,
particularly the hard disk drive.
„
Humidity
High-humidity can cause moisture to enter and accumulate in the system. This
moisture can cause corrosion of internal components and degrade such
properties as electrical resistance and thermal conductivity. Extreme moisture
buildup inside the system can result in electrical shorts, which can cause
serious damage to the system.
Buildings in which climate is controlled usually maintain an acceptable level of
humidity for system equipment. However, if a system is located in an unusually
humid location, a dehumidifier can be used to maintain the humidity within an
acceptable range. Refer to the “Specifications” section of this user’s guide for
the operating and storage humidity specifications.
„
Altitude
Operating a system at a high altitude (low pressure) reduces the efficiency of
the cooling fans to cool the system. This can cause electrical problems related
to arcing and corona effects. This condition can also cause sealed components
with internal pressure, such as electrolytic capacitors, to fail or perform at
reduced efficiency.
Power Protection
The greatest threats to a system’s supply of power are power loss, power spikes,
and power surges caused by electrical storms, which interrupt system operation
and/or damage system components. To protect your system, always properly
ground power cables and one of the following devices.
„
Surge Protector
Surge protectors are available in a variety of types and usually provide a level
of protection proportional with the cost of the device. Surge protectors prevent
voltage spikes from entering a system through the AC power cord. Surge
protectors, however, do not offer protection against brownouts, which occur
when the voltage drops more than 20 percent below the normal AC line voltage
level.
KEEX-4030 User’s Manual
13
Preface
„
Line Conditioner
Line conditioners go beyond the overvoltage protection of surge protectors.
Line conditioners keep a system’s AC power source voltage at a fairly constant
level and, therefore, can handle brownouts. Because of this added protection,
line conditioners cost more than surge protectors. However, line conditioners
cannot protect against a complete loss of power.
„
Uninterruptible Power Supply
Uninterruptible power supply (UPS) systems offer the most complete protection
against variations on power because they use battery power to keep the server
running when AC power is lost. The battery is charged by the AC power while it
is available, so when AC power is lost, the battery can provide power to the
system for a limited amount of time, depending on the UPS system.
UPS systems range in price from a few hundred dollars to several thousand
dollars, with the more expensive unit s allowing you to run larger systems for a
longer period of time when AC power is lost. UPS systems that provide only 5
minutes of battery power let you conduct an orderly shutdown of the system,
but are not intended to provide continued operation. Surge protectors should be
used with all UPS systems, and the UPS system should be Underwriters
Laboratories (UL) safety approved.
KEEX-4030 User’s Manual
14
Chapter 1
Chapter 1
Introduction
„ Overview
The KEEX-4030 is an ECX Form Factor embedded single board computer (SBC)
that combines the high performance Intel® Core™2 Duo processor with Intel®
GM45/ ICH9M chipset and supports DDR3 SODIMM up to 4GB. This SBC offers the
latest performance, features and I/O interfaces at an extremely attractive
price/performance ratio and measures 105mm x 146mm, a 75 percent space
reduction over micro-ATX boards.
The KEEX-4030 features HDMI, DVI and 18/24-bit dual channel LVDS panel
support, SATA 3 Gb/s, RS-232/422/485 serial port, DI/DO, Gigabit Ethernet, USB
2.0, keyboard/mouse, and HD audio. PCIe x4 support provides expansion capability.
Checklist
„
„
„
„
„
SATA cable
Y cable for keyboard & mouse
Driver CD
Quick Installation Guide
KEEX-4030 embedded board
Features
„
„
„
„
„
„
„
„
Intel® Core 2 Duo 45nm Penryn support
Intel® GM45/ICH9-M chipset
1x SO-DIMM DDR3 800/1066 up to 4GB
Intel® Graphics Media Accelerator 4500MHD supports
LVDS/DVI/HDMI, 1x PCIe x4 slot
2x SATA 3 Gb/s, 1x CompactFlash Type II
1x GbE, 6x USB 2.0, HD Audio, 4x DI/DO, 2x COM
Watchdog Timer, Hardware Monitor, TPM 1.2
KEEX-4030 User’s Manual
15
Chapter 1
„ Product Specifications
CPU Support
Intel® 45 nm Penryn-based Core 2 Duo (Socket-P)
Chipset
Intel® GM45 +ICH9M
Memory
1x DDR3 800/1066 SO-DIMM, up to 4 GB
BIOS
AMI Plug & Play BIOS – SPI Flash ROM
Intel® Graphics Media Accelerator 4500MHD
Display
18/24-bit Dual channel LVDS
1x HDMI, 1x DVI-I
LAN
1x RJ-45, Gigabit Ethernet (Intel® 82567)
Audio
HD Audio via optional daughter board
2x SATA 3Gb/s (one with onboard power connector)
1x CompactFlash socket
6x USB 2.0
Peripheral Support
2x COMs (1x RS-232/422/485, 1x RS-232)
4x DI/DO
1x KB/ MS Box Header
1x LPC Box Header
TPM
TPM 1.2
Power Connector
ATX-4P
Expansion
1x PCIe x4 slot (w/ 4x PCIe x1 speed)
Watchdog Timer
1-255 step
Hardware Monitor
Operating voltage, CPU temperature and fan speed
Dimensions
Intel® ECX Form Factor (105 x 146mm)
Operation Temp: 0ºC - 60ºC
Environmental Factors
Storage Temp.: -10ºC - 85ºC
Humidity: 0% - 90%
Certifications
CE, FCC Class A
Table 1 KEEX-4030 Specification
KEEX-4030 User’s Manual
16
Chapter 1
„ System Block Diagram
Figure 1 Block Diagram
KEEX-4030 User’s Manual
17
Chapter 1
„ Mechanical Dimensions
Figure 2 Mechanical Dimensions
KEEX-4030 User’s Manual
18
Chapter 2
Chapter 2
Hardware Settings
„ Overview
This chapter provides the definitions and locations of jumpers, headers, and
connectors.
Jumpers
The product has several jumpers which must be properly configured to ensure
correct operation.
Figure 3 Jumper Connector
For a three-pin jumper (see figure above), the jumper setting is designated “1-2”
when the jumper connects pins 1 and 2. The jumper setting is designated “2-3”
when pins 2 and 3 are connected and so on. You will see that one of the lines
surrounding a jumper pin is thick, which indicates pin No.1.
To move a jumper from one position to another, use needle-nose pliers or tweezers
to pull the pin cap off the pins and move it to the desired position.
KEEX-4030 User’s Manual
19
Chapter 2
„ Jumper Settings and Pin Definitions
For jumper and connector locations, please refer to the diagrams below.
Figure 4 Jumper and Connector Locations
KEEX-4030 User’s Manual
20
Chapter 2
Jumper Settings
To ensure correct system configuration, the following section describes how to set
the jumpers to enable/disable or change functions. For jumper descriptions, please
refer to the table below.
Table 2 Jumper List
Label
JP1
JP2
JP3
JP4
JP5
Function
Power Mode Selection
Clear CMOS Selection
Backlight & Panel Power Selection
Clear ME RTC Registers
Backlight Enable Selection
Table 3 JP1 Power Mode Selection
Jumper
Open
Short
Status
ATX Mode (Default)
AT Mode
Table 4 JP2 Clear CMOS Selection
Jumper
Open
Short
Status
Normal Operation (Default)
Clear CMOS
Table 5 JP3 Backlight & Panel Power Selection
Jumper
1
2
Setting
1-3
3-5
2-4
4-6
Status
Backlight Power = +12V (Default)
Backlight Power = +5V
Panel Power = +3.3V (Default)
Panel Power = +5V
Table 6 JP4 Clear ME RTC Registers
Jumper
Open
Short
Status
Normal Operation (Default)
Clear ME RTC Registers
Table 7 JP5 Backlight Enable Selection
Jumper
1-2
2-3
KEEX-4030 User’s Manual
21
Status
Active High (Default)
Active Low
Chapter 2
Rear Panel Pin Assignments
Table 8 Rear Panel Connector Descriptions
Label
DVI
HDMI1
COM1
LAN1
USB1
Function
DVI-I Connector
HDMI connector
RS-232 Port A DB-9 Connector
10/100/1000 Ethernet RJ-45 Connector
USB2.0 Port 0, 1 Type A Connector
Table 9 DVI (DVI-I Connector)
Pin
1
3
5
7
9
11
13
15
17
19
21
23
PIN
C1
C2
C3
C4
C5
KEEX-4030 User’s Manual
22
Signal Name Pin Signal Name
TX2N
2
TX2P
GND
4
TX5N
TX5P
6
SD_CLK
SD_DATA
8
VSYNC
TX1N
10
TX1P
GND
12
TX4N
TX4P
14
VGA_PWR
VGA_EN
16
HPD
TX0N
18
TX0P
GND
20
TX6N
TX6P
22
GND
TCLP
24
TXLN
Signal Name
Analog red
Analog green
Analog blue
Analog horizontal sync
Analog ground
Chapter 2
Table 10 HDMI1 (HDMI1 connector)
Signal Name
TMD_DATA2+
TMD_DATA2GND
TMD_DATA0+
TMD_DATA0GND
NC
DDC_CLK
GND
HPDET
Pin
1
3
5
7
9
11
13
15
17
19
Pin
2
4
6
8
10
12
14
16
18
Signal Name
GND
TMD_DATA1+
TMD_DATA1GND
HDMI_TCLP
HDMI_TCLN
NC
DDC_DATA
+5V
Table 11 COM1 (RS-232/422/485 Port A DB-9 Connector)
Pin
1
2
3
4
5
6
7
8
9
RS232
RS422
DCD, Data carrier detect
TXRXD, Receive data
RX+
TXD, Transmit data
TX+
DTR, Data terminal ready
RXGND, ground
DSR, Data set ready
RTS, Request to send
CTS, Clear to send
RI, Ring indicator
RS485
Half Duplex
DATAN/A
DATA+
N/A
Table 12 LAN1 (10/100/1000 Ethernet RJ-45 Connector)
Pin
1
2
3
4
5
6
7
8
Signal
Tx+
TxRx+
NC
NC
RxNC
NC
Table 13 USB1 (USB2.0 Port 0, 1 Type A Connector)
Pin
1
2
3
4
KEEX-4030 User’s Manual
Signal Name
+5V
USB1USB1+
GND
23
Pin
5
6
7
8
Signal Name
+5V
USB0USB0+
GND
Chapter 2
Main Board Pin Assignments
Table 14 Connector List
Label
ATX1
CF1
CN1
CN2
CN3
CN4
COM2
DIMM1
FAN1
FP1
FP2
LVDS1
PCIE1
SATA1
SATA2
USB2
USB3
KM1
ATX1
Function
+12V Power Input Connector
CF Type II Connector
Panel Backlight Wafer
Digital Input / Output Pin Header
HD Audio Box Header
LPC Box Header
RS-232 Port B Wafer
DDR3 Memory SO-DIMM Socket
CPU FAN Wafer
Front Panel 1 Pin Header
Front Panel 2 Pin Header
LVDS Panel Connector
PCIE x 4 Slot
Serial ATA & HDD Power Connector
Serial ATA Connector
USB2.0 Port 2, 3 Pin Header
USB2.0 Port 4, 5 Pin Header
Keyboard and mouse connector
+12V Power Input Connector
Table 15 ATX1, +12V Power Input Connector
Pin
Signal Name
1
GND
2
GND
3
+12V
4
+12V
[YIMTEX 576MWA2*02STR]
Table 16 CF1, CF Type II Connector
KEEX-4030 User’s Manual
Pin
Signal Name
Pin
Signal Name
1
2
3
4
5
6
7
8
GND
IDE Data 3
IDE Data 4
IDE Data 5
IDE Data 6
IDE Data 7
IDE Chip select 1#
GND
26
27
28
29
30
31
32
33
GND
IDE Data 11
IDE Data 12
IDE Data 13
IDE Data 14
IDE Data 15
IDE Chip select 3#
GND
24
Chapter 2
9
10
11
12
13
14
15
16
17
18
GND
GND
GND
GND
+5V
GND
GND
GND
GND
SDA2
34
35
36
37
38
39
40
41
42
43
IDEIOR#
IDEIOW#
+5V
IDEIRQ
+5V
PCSEL
NC
Reset IDE
IDEIORDY
DREQ
19
20
21
22
23
24
25
IDE Address 1
IDE Address 0
IDE Data 0
IDE Data 1
IDE Data 2
IOIS16#
GND
44
45
46
47
48
49
50
DACK#
IDE activity
PDIAG#
IDE Data 8
IDE Data 9
IDE Data 10
GND
[JINN SHYANG CF1A-71041-00E01]
Table 17 CN1, Panel Backlight Wafer
Pin Signal Name
1
NC
2
BL_ADJ
3
GND
4
+5V / +12V *
5
+5V / +12V *
6
GND
7
BL_EN / BL_EN# **
Pitch:1.25mm [YIMTEX 501MW1*07MTRR]
* The function can be selected by JP3.
** The function can be selected by JP5.
Table 18 CN2, Digital Input / Output Pin Header
Pin
1
3
5
7
9
Signal
Digital Output 0
Digital Output 1
Digital Output 2
Digital Output 3
+5V
Pin
2
4
6
8
10
Signal
Digital Input 0
Digital Input 1
Digital Input 2
Digital Input 3
GND
Pitch:2.0mm [YIMTEX 3292*05SAGR(6T)]
KEEX-4030 User’s Manual
25
Chapter 2
Table 19 CN3, HD Audio Box Header
Pin
1
3
5
7
9
Signal Name
RST#
GND
SDIN
GND
+5V
Pin
2
4
6
8
10
Signal Name
SYNC
SDOUT
GND
BCLK
+3.3V
Pitch:2.0mm [YIMTEX 32610SAG]
Table 20 CN4, LPC Box Header
Pin Signal Name Pin
1
+3.3V
2
3
GND
4
5
LPC_RST#
6
7
LPC_CLK33
8
9 LPC_FRAME# 10
11 LPC_SERIRQ# 12
Signal Name
GND
LPC_AD3
LPC_AD2
LPC_AD1
LPC_AD0
LPC_DRQ1#
Pitch:1.27mm [YIMTEX 327A121SAG(6T)]
Table 21 COM2, RS-232 Port B Wafer
Pin
1
2
3
4
5
6
7
8
9
10
Signal
DCD, Data carrier detect
DSR, Data set ready
RXD, Receive data
RTS, Request to send
TXD, Transmit data
CTS, Clear to send
DTR, Data terminal ready
RI, Ring indicator
GND, ground
+5V
Pitch:1.25mm [YIMTEX 501MW1*10STR]
Table 22 FAN1, CPU FAN Wafer
Pin
1
2
3
Signal
GND
+12V
FAN_RPM
Pitch:2.54mm YIMTEX 521AW1*03STR
KEEX-4030 User’s Manual
26
Chapter 2
Table 23 FP1, Front Panel 1 Pin Header
Pin
Signal
Pin
Signal
1
Reset Button +
2
Speaker +
3
Reset Button -
4
NC
5
HDD LED +
6
NC
7
HDD LED -
8
Speaker -
Pitch:2.54mm [YIMTEX 3322*04SAGR]
Table 24 FP2, Front Panel 2 Pin Header
Pin
Signal
Pin
Signal
1
Power LED +
2
Power Button +
3
NC
4
Power Button -
5
Power LED -
6
NC
7
Keyboard Lock
8
SMBus Data
9
GND
10
SMBus Clock
Pitch:2.54mm [YIMTEX 3322*05SAGR]
Table 25 LVDS1, LVDS Panel Connector
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal Name
LVDS_A0LVDS_A0+
LVDS_A1LVDS_A1+
LVDS_A2LVDS_A2+
GND
LVDS_ACLKLVDS_ACLK+
LVDS_A3LVDS_A3+
LVDS_B0LVDS_B0+
GND
LVDS_B1-
Pin
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Signal Name
LVDS_B1+
GND
LVDS_B2LVDS_B2+
LVDSBCLKLVDS_BCLK+
LVDS_B3LVDS_B3+
GND
DCC_DAT
VDDEN
DCC_CLK
+3.3V / +5V *
+3.3V / +5V *
+3.3V / +5V *
Pitch:1.00mm JAE FI-X30SSL-HF
* The function can be selected by JP3.
KEEX-4030 User’s Manual
27
Chapter 2
Table 26 SATA1, Serial ATA & HDD Power Connector
Pin
S1
Signal Name
GND
Pin
P5
Signal Name
GND
S2
TX+
P6
GND
S3
TX-
P7
+5V
S4
GND
P8
+5V
S5
RX-
P9
+5V
S6
RX+
P10
GND
S7
GND
P11
GND
P1
+3.3V
P12
GND
P2
+3.3V
P13
+12V
P3
+3.3V
P14
+12V
P4
GND
P15
+12V
7P+15P MALE 180D SATA CONNECTOR BLACK [WIN WIN WATH-22DLBGU4]
Table 27 SATA2, Serial ATA Connector
Pin
Signal Name
1
GND
2
TX+
3
TX-
4
GND
5
RX-
6
RX+
7
GND
7P 180D SATA CONNECTOR BLUE [FOXCONN LD1807V-S52U]
Table 28 USB2, USB2.0 Port 2, 3 Pin Header
Pin
Signal Name
Pin
Signal Name
1
+5V
2
+5V
3
USB2-
4
USB3-
5
USB2+
6
USB3+
7
GND
8
GND
9
KEY
10
GND
Pitch:2.54mm [YIMTEX 3322*05SAGR(6T) -09]
KEEX-4030 User’s Manual
28
Chapter 2
Table 29 USB3, USB2.0 Port 4, 5 Pin Header
Pin
Signal Name
Pin
Signal Name
1
+5V
2
+5V
3
USB4-
4
USB5-
5
USB4+
6
USB5+
7
GND
8
GND
9
KEY
10
GND
Pitch:2.54mm [YIMTEX 3322*05SAGR(6T) -09]
Table 30 KM1, Keyboard and mouse connector
Pin
1
Signal
MS_CLK
2
+5V
3
MS_DATA
4
KB_DAT
5
GND
6
KB_CLK
CONN WAFER DIP 6P MALE 1R 180D P=2.0mm [STM M24266]
KEEX-4030 User’s Manual
29
Chapter 3
Chapter 3
System Installation
„ Processor Installation
Processor Handling
Carefully follow the steps below in order to prepare the CPU for installation:
1. Remove processor from packaging.
2. Handle the CPU by grasping the substrate edges only with thumb and
forefinger.
CAUTION
DO NOT TOUCH PROCESSOR CONTACTS TO PREVENT
DAMAGING THE CPU.
Installing the CPU
Carefully follow the steps below in order to install the CPU:
1. Check and confirm that you are installing the correct CPU type.
2. Using a screwdriver, disengage (open) the socket actuator, as shown in figure
below.
Figure 5 Disengage the socket actuator
KEEX-4030 User’s Manual
30
Chapter 3
3.
Align the gold triangle on the CPU with the similar marking on the socket (see
Figure below). If the processor does not drop completely into the socket, turn the
socket actuator to the open position until the processor drops completely in.
Note: You should not have to press down on the processor. If the processor does not
drop completely into the socket, turn the actuator until the processor drops completely in.
Figure 6 CPU alignment in Micro-FCPGA Socket (Socket P)
4.
While gently holding the processor down with your finger, secure the processor
in the socket with a screwdriver by turning the socket actuator to the closed
position:
Figure 7 Secure the processor in the socket
Removing the CPU:
To remove the CPU, reverse the installation steps.
1. Before removing the CPU, turn off the system power and wait for about 20
minutes until the heat radiation plate of the cooling fan and the CPU cools
KEEX-4030 User’s Manual
31
Chapter 3
2.
3.
down.
To remove the CPU, follow Step 2 of Installing the CPU above.
Remove the CPU by grasping the substrate edges only with thumb and
forefinger and lifting it out with a purely vertical motion.
WARNING
The CPU and the heatsink may be hot and could cause burns.
„ Cooler Installation
The system must not be operated without a cooler (heat sink and fan) to provide the
necessarily cooling. Install the cooling unit supplied as follows:
CAUTION
Make sure that good thermal contact is made between the processor and
heat sink. Insufficient contact or incorrect use of heat sink, fan, or thermal
compound can cause the processor to overheat, which may crash the
system or cause permanent damage to the CPU.
1.
2.
Install the correct CPU as described above.
Align the screw holes of the heatsink rear retention bracket with the mounting
holes on the underside of the motherboard, located at the four corners of the
CPU location. Insert into the holes and turn the motherboard over.
Note: Be careful not to touch the thermal pad on the underside of the heatsink. This pad is
made of thermal compound and is deformable. It is designed to make optimal thermal contact
with the CPU. No additional thermal compound is required.
3.
Tighten each screw halfway to secure the cooler assembly to the motherboard.
Then gradually tighten all four screws. Do not fully tighten the first screw before
partially tightening the other screws as this may apply uneven pressure to the
CPU, causing damage.
Note: Fan less Operation: In order to operate the KEEX-4030 without a fan, the cooling solution
must be integrally designed with the chassis. Contact Quanmax for more information on fan
less operation.
KEEX-4030 User’s Manual
32
Chapter 3
„ Memory Module Installation
Carefully follow the steps below in order to install the DIMMs:
1.
2.
3.
To avoid generating static electricity and damaging the SO-DIMM, ground
yourself by touching a grounded metal surface or use a ground strap before you
touch the SO-DIMM.
Do not touch the connectors of the SO-DIMM. Dirt or other residue may cause a
malfunction.
Hold the SO-DIMM with its notch aligned with the memory socket of the board
and insert it at a 30-degree angle into the socket.
Figure 8 Align the SO-DIMM Memory Module with the onboard socket
4.
5.
Fully insert the module into the socket until a “click” is heard.
Press down on the SO-DIMM so that the tabs of the socket lock on both sides
of the module
Figure 9 Press down on the SO-DIMM Memory Module to lock it in place
Removing a DIMM:
To remove the SO-DIMM, use your fingers or a small screwdriver to carefully push
away the tabs that secure either side of the SO-DIMM. Lift it out of the socket.
Note: Make sure you store the SO-DIMM in an anti-static bag. The socket must be populated
with memory modules of the same size and manufacturer.
KEEX-4030 User’s Manual
33
Chapter 4
Chapter 4
AMI BIOS Setup
„ Overview
This chapter provides a description of the AMI BIOS. The BIOS setup menus and
available selections may vary from those of your product. For specific information on
the BIOS for your product, please contact Quanmax.
NOTE: The BIOS menus and selections for your product may vary from those in this
chapter. For the BIOS manual specific to your product, please contact Quanmax.
AMI's ROM BIOS provides a built-in Setup program, which allows the user to modify
the basic system configuration and hardware parameters. The modified data will be
stored in a battery-backed CMOS, so that data will be retained even when the power
is turned off. In general, the information saved in the CMOS RAM will not need to be
changed unless there is a configuration change in the system, such as a hard drive
replacement or when a device is added.
It is possible for the CMOS battery to fail, which will cause data loss in the CMOS
only. If this happens you will need to reconfigure your BIOS settings.
KEEX-4030 User’s Manual
34
Chapter 4
„ Main Menu
The BIOS Setup is accessed by pressing the DEL key after the Power-On Self-Test
(POST) memory test begins and before the operating system boot begins. Once you
enter the BIOS Setup Utility, the Main Menu will appear on the screen. The Main
Menu provides System Overview information and allows you to set the System Time
and Date. Use the “<” and “>” cursor keys to navigate between menu screens.
Table 31 BIOS Main Menu
BIOS SETUP UTILITY
Main
Advanced
Boot
Chipset
System Date
System Time
Power
[Mon 01/21/2008]
[10:18:15]
> Primary IDE Master
> Primary IDE Slave
> Secondary IDE Master
> Fourth IDE Master
:[Not Detected]
:[Not Detected]
:[Not Detected]
:[Not Detected]
Security
Exit
While entering setup, BIOS
auto detects the presence of
IDE device. This displays the
status of auto detection of IDE
device.
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
> System Information
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Below table is described for Primary IDE Master, Primary IDE Slave, Secondary IDE
Master, Fourth IDE Master setting.
.
Table 32 IDE Device Setting Menu
BIOS SETUP UTILITY
Main
Advanced
Boot
Chipset
Primary IDE Master
Device
:Not Detected
Power
Security
Exit
Select the type of device
connected to the system.
LBA/ Large Mode
DMA Mode
S.M.A.R.T
[Auto]
[Auto]
[Auto]
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
KEEX-4030 User’s Manual
35
Chapter 4
LBA/ Large Mode [Auto]
Enables or disables the LBA (Logical Block Addressing)/ Large mode. Setting to
Auto enables the LBA mode if the device supports this mode, and if the device was
not previously formatted with LBA mode disabled.
Options: Disabled, Auto
DMA Mode [Auto]
Setup DMA Mode.
S.M.A.R.T [Auto]
SMART stands for Smart Monitoring, Analysis, and Reporting Technology. It allows
AMIBIOS to use the SMART protocol to report server system information over a
network.
Options: Auto, Disabled, Enabled
Table 33 System Information
BIOS SETUP UTILITY
Main
Advanced
AMIBIOS
Version
Build Date:
Boot
Chipset
Power
Security
Exit
: 0.08
:01/07/09
Processor
Intel(R) CORE(TM)2 Duo CPU T9400
Speed
:2533MHz
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
@2.53GHz
System Memory
Size
:989
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
„ Advanced Menu
Table 34 Advanced Menu
BIOS SETUP UTILITY
Main
Advanced
Boot
Chipset
Power
Security
Advanced Settings
Warning:
Setting wrong values in below sections
may cause system to malfunction.
> SuperIO Configuration
> OnBoard Peripherals Configuration
> iTPM function
> Hardware Health Configuration
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
KEEX-4030 User’s Manual
36
Exit
Chapter 4
Press <Enter> to select a sub-menu for detailed options.
Table 35 Super I/O Configuration
BIOS SETUP UTILITY
Main
Advanced
Boot
Chipset
Power
Security
Exit
Allow BIOS to Select Serial
Port1 Base Addresses.
Onboard I/O Configuration
Serial Port1 Address
COM1 Function Type
COM1 Pin9 Voltage
Serial Port2 Address
COM2 Pin9 Voltage
[3F8/IRQ4]
[RS232]
[Normal]
[2F8/IRQ3]
[Normal]
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Serial Port1 Address [3F8/IRQ4]
Options: Disabled, 3F8/IRQ4, 3E8/IRQ4, 2E8/IRQ3
COM1 Function Type [RS232]
Options: RS232, RS422, RS485
COM1 Pin9 Voltage [Normal]
Options: Normal, 5V, 12V
Serial Port2 Address [2F8/IRQ3]
Options: Disabled, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3
COM2 Pin9 Voltage [Normal]
Options: Normal, 5V, 12V
Table 36 OnBoard Peripherals Configuration Settings
BIOS SETUP UTILITY
Main
Advanced
Boot
Chipset
Power
Security
Options
OnBoard Peripherals Configuration Settings
[Enabled]
USB Functions
[Enabled]
Legacy USB Support
[Enabled]
GbE Controller
[Disabled]
GbE LAN Boot
[Enabled]
HDA Controller
Disabled
Enabled
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
KEEX-4030 User’s Manual
37
Exit
Chapter 4
USB Functions [Enabled]
Options: Disabled, Enabled
Legacy USB Support [Enabled]
Options: Disabled, Enabled, Auto
GbE LAN Boot [Disabled]
Options: Disabled, Enabled
HDA Controller
Options: Disabled, Enabled
Table 37 iTPM Function
BIOS SETUP UTILITY
Main
Advanced
ITPM Function
TCG/TPM SUPPORT
Boot
Chipset
Power
Security
Enable/ Disable TPM
TCG (TPM 1.1/1.2) supp
in BIOS
[NO]
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
TCG/TPM SUPPORT [No]
Options: No, Yes
If the value is Enabled.
Execute TPM Command [Don’t change]
Options: Don’t change, Disabled, Enabled
KEEX-4030 User’s Manual
Exit
38
Chapter 4
Table 38 Hardware Health Configuration
BIOS SETUP UTILITY
Main
Advanced
Hardware Health Configuration
CPU Warning Temperature
CPU Shutdown Temperature
Boot
Chipset
Power
Security
Options
[Disabled]
[Disabled]
SYS Temperature
CPU Temperature
:57°C/ 134°F
:43°C/ 109°F
Fan1 Speed
:6490RPM
CPU Core
Vcc
+3.30V
+5.00V
+12.0V
5VSB
VBAT
:1.136 V
:1.040V
:3.166 V
:4.958 V
:11.182 V
: 4.945 V
:3.344 V
Disabled
80°C/176°F
85°C/185°F
90°C/194°F
95°C/203°F
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
CPU Warning Temperature [Disabled]
Options: Disabled, 80°C/176°F, 85°C/185°F, 90°C/194°F, 95°C/203°F
CPU Shutdown Temperature [Disabled]
Options: Disabled, 80°C/176°F, 85°C/185°F, 90°C/194°F, 95°C/203°F
KEEX-4030 User’s Manual
39
Exit
Chapter 4
„ Boot Menu
Table 39 Boot Menu
BIOS SETUP UTILITY
Main
Advanced
Boot
Chipset
Power
Exit
Specifies the Boot Device
Priority sequence.
Boot Settings
> Boot Device Priority
> Hard Disk Drives
Quick Boot
Full Screen LOGO Display
Bootup Num-Lock
Wait For ’F1’ If Error
Hit ’DEL’Message Display
Security
[Enabled]
[Disabled]
[On]
[Enabled]
[Enabled]
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Boot Device Priority
The items allow you to specify the Boot Device Priority sequence.
Hard Disk Drives
The items allow you to specify the Boot Device Priority sequence from available
Removable Drives.
Quick Boot [Enabled]
Enabling this item allows BIOS to skip some Power On Self Tests (POST) while
booting to decrease the time needed to boot the system. When set to [Disabled],
BIOS performs all the POST items.
Options: Disabled, Enabled
Full Screen LOGO Display [Disabled]
This item allows you to display normal or OEM logo POST message.
Bootup Num-Lock [On]
Allow you to select the power-on state for the NumLock.
Options: Off, On
Wait for ‘F1’ If Error [Enabled]
When set to Enabled, the system waits for F1 key to be pressed when error occurs.
Options: Disabled, Enabled
Hit ‘DEL’ Message Display [Enabled]
When set to Enabled, the system displays the message ‘Press DEL to run Setup’
during POST.
Options: Disabled, Enabled
KEEX-4030 User’s Manual
40
Chapter 4
„ Chipset Menu
Table 40 Chipset Menu
BIOS SETUP UTILITY
Main
Advanced
Boot
Chipset
Chipset Settings
Power
Security
Exit
Select which graphics
Boot Graphics Adapter Priority
Internal Graphics Mode Select
Gfx Low Power Mode
[PEG/PCI]
[Enabled, 32MB]
[Disabled]
> Video Function Configuration
controller to use as the
primary boot device.
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Boots Graphic Adapter Priority [PEG/PCI]
Select which graphics controller to use as the primary boot device.
Options: IGD, PCI/IGD, PCI/PEG, PEG/IGD, PEG/PCI
Internal Graphics Mode Select [Enabled, 32MB]
Select the amount of system memory used by the Internal graphics device.
Options: Enabled 32MB, Enabled 64MB, Enabled 128MB
Gfx Low Power Mode [Disabled]
This option is applicable for SFF only.
Options: Disabled, Enabled
Press <Enter> to select a sub-menu for Video Function Configuration.
KEEX-4030 User’s Manual
41
Chapter 4
Table 41 Video Function Configuration
BIOS SETUP UTILITY
Main
Advanced
Boot
Video Function Configuration
DVMT Mode Select
DVMT/FIXED memory
PAVP Mode
Boot Display Device
Flat Panel Type
HDCP Support
Panel Backlight Voltage
Chipset
Power
Security
Exit
Options
[DVMT Mode]
[256 MB]
[Disabled]
[DVI]
[1024x768 18Bit 1C]
[Disabled]
[2.5]
DVMT Mode
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
DVMT Mode Select [DVMT Mode]
Options: DVMT Mode
DVMT/FIXED Memory [256MB]
Options: 128MB, 256MB, Maximum DVMT
PAVP Mode [Disabled]
PAVP (Protected Audio Video Path) is a feature to ensure a robust and secure
content protection path for high-definition video playback.
Options: Disabled, Lite, High
Boot Display Device [DVI]
Options: DVI, LVDS, VGA+LVDS
Flat Panel Type [1024x768 18 Bit 1CH]
Options:
640x480 18 Bit 1CH
1024x768 18 Bit 1CH
800x600 18 Bit 1CH
1280x800 18 Bit 1CH
HDCP Support [Disabled]
Options: Disabled, Enabled
Panel BackLight Voltage [2.5]
Options: Min 0.0V, Max: 5.0V
KEEX-4030 User’s Manual
42
Chapter 4
„ Power Menu
Table 42 Power Menu
BIOS SETUP UTILITY
Main
Advanced
Boot
Power Management Setting
ACPI Function
Suspend mode
Repost Video on S3 Resume
Suspend Time Out
Power Button Mode
Restore on AC Power Loss
USB Device Wakeup From S3/S4
GbE Wake Up From S5
Resume On RTC Alarm
Chipset
Security
Power
[Enabled]
[S3 (STR)]
[No]
[Disabled]
[On/Off]
[Power On]
[Disabled]
[Disabled]
[Disabled]
Exit
Enable/ Disable ACPI support for
Operating System.
ENABLE: If OS supports ACPI,
DISABLE: IF OS Does not support
ACPI.
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
ACPI Function [Enabled]
Enable/ Disable ACPI support for Operating System.
ENABLE: If OS supports ACPI, DISABLE: IF OS Does not support ACPI.
Suspend mode [S3 (STR)]
Options: S1 (POS), S3 (STR)
Repost Video on S3 Resume [No]
Options: No, Yes
Suspend Time Out [Disabled]
Options: Disabled, 1 Min, 2 Min, 4 Min, 8 Min, 10 Min, 20 Min, 30 Min, 40 Min, 50 Min, 60 Min
Power Button Mode [On/Off]
Go into On/Off, or Suspend when Power button is pressed.
Options: On/Off, Suspend
Restore on AC Power Loss [Power Off]
Options: Power OFF, Power ON, Last State
USB Device Wakeup From S3/S4 [Disabled]
Enable/ Disable USB Device Wakeup From S3/S4
Options: Disabled, Enabled
GbE Wake Up Form S5 [Disabled]
Options: Disabled, Enabled
Resume On RTC Alarm [Disabled]
Options: Disabled, Enabled
If the value is Enabled.
RTC Alarm Date (Days) [Every Day]
KEEX-4030 User’s Manual
KeyIn “+”/”-“ to select
43
Chapter 4
RTC Alarm Time
[00:00:00]
Use [ENTER], [TAB] or [SHIFT+TAB] to select a field
Use [+] or [-] to configure system time
„ Security Menu
Table 43 Security Menu
BIOS SETUP UTILITY
Main
Advanced
Boot
Chipset
Power
Security
Exit
Install or Change the password.
Security Setting
Supervisor Password :Not Installed
User Password :Not Installed
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
Change Supervisor Password
Change User Password
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Change Supervisor Password
Select this item to set or change the supervisor password. The Supervisor Password
item on top of the screen displays the default Not Installed. After you have set a
password, this item displays Installed.
Change User Password
Select this item to set or change the user password. The User Password item on top
of the screen displays the default Not Installed. After you have set a password, this
item displays Installed.
„ Exit Menu
Table 44 Exit Menu
BIOS SETUP UTILITY
Main
Advanced
Boot
Chipset
Power
Security
Exit System Setup after saving the changes.
Exit Setting
F10 key can be used for this operation.
Save Changes and Exit
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
Discard Changes and Exit
Discard Changes
Load Optimal Defaults
Load Failsafe Defaults
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
KEEX-4030 User’s Manual
Exit
44
Chapter 4
Save Changes and Exit
Exit system setup after saving the changes. Once you are finished making your
selections, choose this option from the Exit menu to ensure the values you selected
are saved to the CMOS RAM. The CMOS RAM is sustained by an onboard backup
battery and stays on even when the PC is turned off. When you select this option, a
confirmation window appears. Select [Yes] to save changes and exit.
Discard Changes and Exit
Exit system setup without saving any changes. Select this option only if you do not
want to save the changes that you made to the Setup program. If you made changes
to fields other than system date, system time, and password, the BIOS asks for a
confirmation before exiting.
Discard Changes
Discards changes done so far to any of the setup values. This option allows you to
discard the selections you made and restore the previously saved values. After
selecting this option, a confirmation appears. Select [Yes] to discard any changes and
load the previously saved values.
Load Optimal Defaults
Load Optimal Default values for all the setup values. This option allows you to load
optimal default values for each of the parameters on the Setup menus, which will
provide the best performance settings for your system. The F9 key can be used for
this operation.
Load Failsafe Defaults
Load Optimal Default values for all the setup values. This option allows you to load
failsafe default values for each of the parameters on the Setup menus, which will
provide the most stable performance settings. The F8 key can be used for this
operation.
KEEX-4030 User’s Manual
45
Chapter 5
Chapter 5
Driver Installation
If your KEEX-4030 does not come with an operating system pre-installed, you will
need to install an operating system and the necessary drivers to operate it. After you
have finished assembling your system and connected the appropriate power source,
power it up using the power supply and install the desired operating system.
You can download the drivers for the KEEX-4030 from the Quanmax website at
www.quanmax.com and install as instructed there. For other operating systems,
please contact Quanmax.
NOTE
You have to install Windows XP/2K HD Audio Service Pack before you
start graphic driver installation.
Please visit http://support.microsoft.com/kb/888111 for more
information.
NOTE
When the system reboots without connecting the CRT, there might be no
image on screen when you insert the CRT/VGA cable. Please
pressing <Ctrl>+<Alt>+<F1> simultaneously to show the image on screen.
KEEX-4030 User’s Manual
46
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement