Lenovo ThinkCentre 6417, 6418, 6449, 6453 computer Hardware Maintenance Manual
Below you will find brief information for ThinkCentre 6417, ThinkCentre 6418, ThinkCentre 6449. This manual contains service and information for ThinkCentre computers. It is intended only for trained servicers who are familiar with Lenovo computer products.
advertisement
Assistant Bot
Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.
▼
Scroll to page 2
of
144
ThinkCentre Hardware Maintenance Manual Machine Types 6417, 6418, 6449, 6453 ThinkCentre Hardware Maintenance Manual Note: Before using this information and the product it supports, be sure to read the information under “Notices,” on page 135. Second Edition (September 2007) © Copyright Lenovo 2006, 2007. All rights reserved. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure. LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered pursuant a General Services Administration ″GSA″ contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925. Contents Chapter 1. About this manual . . . . . 1 Important Safety Information . . . . . . Important information about replacing RoHS compliant FRUs . . . . . . . . . . . . . 1 . . . 2 Chapter 2. Safety information . . . . . 3 General safety . . . . . . . . . . . . Electrical safety . . . . . . . . . . . Safety inspection guide . . . . . . . . . Handling electrostatic discharge-sensitive devices Grounding requirements . . . . . . . . Safety notices (multi-lingual translations) . . . . . . . . . . . . . . . 3 3 5 6 6 7 Chapter 3. General information . . . . 37 The ThinkVantage Productivity Center program . Additional information resources . . . . . . Specifications . . . . . . . . . . . . . . 37 . 37 . 38 Chapter 4. General Checkout . . . . . 39 Checking for power problems . Problem determination tips . . . . . . . . . . . . . . . 39 . 40 Chapter 5. Diagnostics . . . . . . . . 43 PC-Doctor for Windows . . . . . . . . . PC-Doctor for Windows PE . . . . . . . . Running diagnostics from the Rescue and Recovery workspace . . . . . . . . . PC-Doctor for DOS . . . . . . . . . . . Creating a diagnostic CD image . . . . . Creating diagnostic diskettes . . . . . . Running diagnostics from the CD or diskettes . Navigating through the diagnostics programs . Running tests . . . . . . . . . . . . Viewing the test log . . . . . . . . . . 43 . 43 . . . . . . . . 43 44 44 44 45 45 45 47 Chapter 6. Using the Setup Utility . . . 49 Starting the Setup Utility program . . . . . . . Viewing and changing settings . . . . . . . . Using passwords . . . . . . . . . . . . Password considerations . . . . . . . . . User Password . . . . . . . . . . . . Administrator Password . . . . . . . . . Setting, changing, and deleting a password . . . Selecting a startup device . . . . . . . . . . Selecting a temporary startup device . . . . . Selecting or changing the startup device sequence Advanced settings . . . . . . . . . . . . Exiting from the Setup Utility program . . . . . 49 49 49 49 50 50 50 50 50 51 51 51 Chapter 7. Symptom-to-FRU Index . . . 53 © Copyright Lenovo 2006, 2007 Hard disk drive boot error . Diagnostic error codes . . . Beep symptoms . . . . . POST error codes . . . . Miscellaneous error messages Undetermined problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 54 74 75 77 78 Chapter 8. Replacing FRUs . . . . . . 79 Locations . . . . . . . . . . . . . . . 80 Connectors on the front of the computer. . . . 80 Connectors on the rear of the computer . . . . 81 Locating components . . . . . . . . . . 82 System board locations . . . . . . . . . 83 Opening the cover . . . . . . . . . . . . 84 Replacing the CMOS battery. . . . . . . . . 85 Replacing the microprocessor . . . . . . . . 86 Replacing the system board . . . . . . . . . 89 Replacing a hard disk drive . . . . . . . . . 90 Replacing an optical drive . . . . . . . . . 92 Replacing a memory module . . . . . . . . 94 Replacing the modem . . . . . . . . . . . 95 Replacing the Express card assembly . . . . . . 97 Replacing the Media Card Reader . . . . . . . 99 Replacing the system fan assembly . . . . . . 101 Completing the FRU replacement . . . . . . 103 Chapter 9. FRU lists . . . . . . . . 105 Machine Machine Machine Machine Type Type Type Type 6417 6418 6449 6453 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 112 118 124 Chapter 10. Additional Service Information . . . . . . . . . . . . 131 Security features . . . . . . . . . . . Hardware controlled Passwords . . . . . Operating system password . . . . . . Vital product data . . . . . . . . . . BIOS levels . . . . . . . . . . . . . Updating (flashing) BIOS from a CD-ROM or diskette . . . . . . . . . . . . . . Recovering from a POST/BIOS update failure . Power management . . . . . . . . . . Automatic configuration and power interface (ACPI) BIOS . . . . . . . . . . . . Automatic Power-On features . . . . . . . . . . . 131 131 131 131 131 . 132 . 132 . 133 . 133 . 133 Appendix. Notices . . . . . . . . . 135 Television output notice . Trademarks . . . . . . . . . . . . . . . . . . . . . . 136 . 136 iii iv Hardware Maintenance Manual Chapter 1. About this manual This manual contains service and reference information for ThinkCentre® computers listed on the cover. It is intended only for trained servicers who are familiar with Lenovo computer products. Before servicing a Lenovo product, be sure to read the Safety Information. See Chapter 2, “Safety information,” on page 3. This manual includes a complete Field Replaceable Unit (FRU) part number listing for each machine type listed on the cover. If you have internet access, FRU part numbers are also available at: http:/www.lenovo.com/support Important Safety Information Be sure to read all caution and danger statements in this book before performing any of the instructions. Veuillez lire toutes les consignes de type DANGER et ATTENTION du présent document avant d’exécuter les instructions. Lesen Sie unbedingt alle Hinweise vom Typ ″ACHTUNG″ oder ″VORSICHT″ in dieser Dokumentation, bevor Sie irgendwelche Vorgänge durchführen Leggere le istruzioni introdotte da ATTENZIONE e PERICOLO presenti nel manuale prima di eseguire una qualsiasi delle istruzioni Certifique-se de ler todas as instruções de cuidado e perigo neste manual antes de executar qualquer uma das instruções Es importante que lea todas las declaraciones de precaución y de peligro de este manual antes de seguir las instrucciones. © Copyright Lenovo 2006, 2007 1 Important information about replacing RoHS compliant FRUs RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market and sold in the European Union after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts. If the parts are not compliant originally, replacement parts can also be noncompliant, but in all cases, if the parts are compliant, the replacement parts must also be compliant. Note: RoHS and non-RoHS FRU part numbers with the same fit and function are identified with unique FRU part numbers. Lenovo plans to transition to RoHS compliance well before the implementation date and expects its suppliers to be ready to support Lenovo’s requirements and schedule in the EU. Products sold in 2005, will contain some RoHS compliant FRUs. The following statement pertains to these products and any product Lenovo produces containing RoHS compliant parts. RoHS compliant ThinkCentre parts have unique FRU part numbers. Before or after June, 2006, failed RoHS compliant parts must always be replaced using RoHS compliant FRUs, so only the FRUs identified as compliant in the system HMM or direct substitutions for those FRUs can be used. Products marketed before June 2006 Products marketed after June 2006 Current or original part Replacement FRU Current or original part Replacement FRU Non-RoHS Can be Non-RoHS Must be RoHS Must be RoHS Non-RoHS Can be RoHS Non-RoHS Can sub to RoHS RoHS Must be RoHS Note: A direct substitution is a part with a different FRU part number that is automatically shipped by the distribution center at the time of order. 2 Hardware Maintenance Manual Chapter 2. Safety information This chapter contains the safety information that you need to be familiar with before servicing a computer. General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Ensure you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift. 4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back. Do not attempt to lift any objects that weigh more than 16 kg (35 lb) or objects that you think are too heavy for you. v Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe. v Before you start the machine, ensure that other service representatives and the customer’s personnel are not in a hazardous position. v Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the machine. v Keep your tool case away from walk areas so that other people will not trip over it. v Do not wear loose clothing that can be trapped in the moving parts of a machine. Ensure that your sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it. v Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, approximately 8 centimeters (3 inches) from the end. v Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing. Remember: Metal objects are good electrical conductors. v Wear safety glasses when you are: hammering, drilling soldering, cutting wire, attaching springs, using solvents, or working in any other conditions that might be hazardous to your eyes. v After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective. v Reinstall all covers correctly before returning the machine to the customer. Electrical safety © Copyright Lenovo 2006, 2007 3 CAUTION: Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect the attached power cords, telecommunication systems, networks, and modems before you open the server/workstation covers, unless instructed otherwise in the installation and configuration procedures. Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. v v v v v v v v 4 Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock. Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly. Do not work alone under hazardous conditions or near equipment that has hazardous voltages. Disconnect all power before: – Performing a mechanical inspection – Working near power supplies – Removing or installing Field Replaceable Units Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer to power-off the wall box that supplies power to the machine and to lock the wall box in the off position. If you need to work on a machine that has exposed electrical circuits, observe the following precautions: – Ensure that another person, familiar with the power-off controls, is near you. Remember: Another person must be there to switch off the power, if necessary. – Use only one hand when working with powered-on electrical equipment; keep the other hand in your pocket or behind your back. Remember: There must be a complete circuit to cause electrical shock. By observing the above rule, you may prevent a current from passing through your body. – When using testers, set the controls correctly and use the approved probe leads and accessories for that tester. – Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal floor strips and machine frames. Observe the special safety precautions when you work with very high voltages; these instructions are in the safety sections of maintenance information. Use extreme care when measuring high voltages. Regularly inspect and maintain your electrical hand tools for safe operational condition. Do not use worn or broken tools and testers. Never assume that power has been disconnected from a circuit. First, check that it has been powered-off. Hardware Maintenance Manual v Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. v Do not service the following parts with the power on when they are removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.) v If an electrical accident occurs: – Use caution; do not become a victim yourself. – Switch off power. – Send another person to get medical aid. Safety inspection guide The intent of this inspection guide is to assist you in identifying potentially unsafe conditions on these products. Each machine, as it was designed and built, had required safety items installed to protect users and service personnel from injury. This guide addresses only those items. However, good judgment should be used to identify potential safety hazards due to attachment of features or options not covered by this inspection guide. If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem. Consider these conditions and the safety hazards they present: v Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal electrical shock). v Explosive hazards, such as a damaged CRT face or bulging capacitor v Mechanical hazards, such as loose or missing hardware The guide consists of a series of steps presented in a checklist. Begin the checks with the power off, and the power cord disconnected. Checklist: 1. Check exterior covers for damage (loose, broken, or sharp edges). 2. Power-off the computer. Disconnect the power cord. 3. Check the power cord for: a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity for 0.1 ohm or less between the external ground pin and frame ground. b. The power cord should be the appropriate type as specified in the parts listings. c. Insulation must not be frayed or worn. 4. Open the cover. Chapter 2. Safety information 5 5. Check for any obvious alterations. Use good judgment as to the safety of any alterations. 6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage. 7. Check for worn, frayed, or pinched cables. 8. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with. Handling electrostatic discharge-sensitive devices Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes: 1. Use product-specific ESD procedures when they exceed the requirements noted here. 2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective. When handling ESD-sensitive parts: v Keep the parts in protective packages until they are inserted into the product. v Avoid contact with other people while handling the part. v Wear a grounded wrist strap against your skin to eliminate static on your body. v Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap. v Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices. v Select a grounding system, such as those listed below, to provide protection that meets the specific service requirement. Note: The use of a grounding system is desirable but not required to protect against ESD damage. – Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground. – Use an ESD common ground or reference point when working on a double-insulated or battery-operated system. You can use coax or connector-outside shells on these systems. – Use the round ground-prong of the ac plug on ac-operated computers. Grounding requirements Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician. 6 Hardware Maintenance Manual Safety notices (multi-lingual translations) The caution and danger safety notices in this section are provided in the following languages: v English v Arabic v Brazilian/Portuguese v Chinese (simplified) v v v v v v v Chinese (traditional) French German Hebrew Italian Korean Spanish DANGER Electrical current from power, telephone and communication cables is hazardous. To avoid a shock hazard: v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. v Connect all power cords to a properly wired and grounded electrical outlet. v Connect to properly wired outlets any equipment that will be attached to this product. v When possible, use one hand only to connect or disconnect signal cables. v Never turn on any equipment when there is evidence of fire, water, or structural damage. v Disconnect the attached power cords, telecommunications systems, networks, and modems before you open the device covers, unless instructed otherwise in the installation and configuration procedures. v Connect and disconnect cables as described in the following tables when installing, moving, or opening covers on this product or attached devices. To Connect To Disconnect 1. Turn everything OFF. 1. Turn everything OFF. 2. First, attach all cables to devices. 2. First, remove power cords from outlet. 3. Attach signal cables to connectors. 3. Remove signal cables from connectors. 4. Attach power cords to outlet. 4. Remove all cables from devices. 5. Turn device ON. Chapter 2. Safety information 7 CAUTION: When replacing the lithium battery, use only Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: v Throw or immerse into water v Heat to more than 100°C (212°F) v Repair or disassemble Dispose of the battery as required by local ordinances or regulations. CAUTION: When laser products (such as CD-ROMs, DVD-ROM drives, fiber optic devices, or transmitters) are installed, note the following: v Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. v Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure. DANGER: Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following: Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) CAUTION: Use safe practices when lifting. 8 Hardware Maintenance Manual ≥55 kg (121.2 lbs) CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source. 2 1 Chapter 2. Safety information 9 10 Hardware Maintenance Manual Chapter 2. Safety information 11 ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) 2 1 12 Hardware Maintenance Manual PERIGO A corrente elétrica proveniente de cabos de alimentação, de telefone e de comunicações é perigosa. Para evitar risco de choque elétrico: v Não conecte nem desconecte nenhum cabo ou execute instalação, manutenção ou reconfiguração deste produto durante uma tempestade com raios. v Conecte todos os cabos de alimentação a tomadas elétricas corretamente instaladas e aterradas. v Todo equipamento que for conectado a este produto deve ser conectado a tomadas corretamente instaladas. v Quando possível, utilize apenas uma das mãos para conectar ou desconectar cabos de sinal. v Nunca ligue nenhum equipamento quando houver evidência de fogo, água ou danos estruturais. v Antes de abrir tampas de dispositivos, desconecte cabos de alimentação, sistemas de telecomunicação, redes e modems conectados, a menos que especificado de maneira diferente nos procedimentos de instalação e configuração. v Conecte e desconecte os cabos conforme descrito na tabela apresentada a seguir ao instalar, mover ou abrir tampas deste produto ou de dispositivos conectados. Para Conectar: Para Desconectar: 1. DESLIGUE Tudo. 1. DESLIGUE Tudo. 2. Primeiramente, conecte todos os cabos aos dispositivos. 2. Primeiramente, remova os cabos de alimentação das tomadas. 3. Conecte os cabos de sinal aos conectores. 3. Remova os cabos de sinal dos conectores. 4. Remova todos os cabos dos dispositivos. 4. Conecte os cabos de alimentação às tomadas. 5. LIGUE os dispositivos. Chapter 2. Safety information 13 CUIDADO: Ao substituir a bateria de lítio, utilize apenas uma bateria com Número de Peça 33F8354 ou um tipo de bateria equivalente recomendado pelo Se o seu sistema possui um módulo com uma bateria de lítio, substitua-o apenas por um módulo do mesmo tipo e do mesmo fabricante. A bateria contém lítio e pode explodir se não for utilizada, manuseada ou descartada de maneira correta. Não: v Jogue ou coloque na água v Aqueça a mais de 100°C (212°F) v Conserte nem desmonte Descarte a bateria conforme requerido pelas leis ou regulamentos locais. PRECAUCIÓN: Quando produtos a laser (como unidades de CD-ROMs, unidades de DVD-ROM, dispositivos de fibra ótica ou transmissores) estiverem instalados, observe o seguinte: v Não remova as tampas. A remoção das tampas de um produto a laser pode resultar em exposição prejudicial à radiação de laser. Não existem peças que podem ser consertadas no interior do dispositivo. v A utilização de controles ou ajustes ou a execução de procedimentos diferentes dos especificados aqui pode resultar em exposição prejudicial à radiação. PERIGO Alguns produtos a laser contêm diodo de laser integrado da Classe 3A ou da Classe 3B. Observe o seguinte: Radiação a laser quando aberto. Não olhe diretamente para o feixe a olho nu ou com instrumentos ópticos e evite exposição direta ao feixe. ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) CUIDADO: Utilize procedimentos de segurança para levantar equipamentos. 14 Hardware Maintenance Manual CUIDADO: O botão de controle de alimentação do dispositivo e o botão para ligar/desligar da fonte de alimentação não desligam a corrente elétrica fornecida ao dispositivo. O dispositivo também pode ter mais de um cabo de alimentação. Para remover toda a corrente elétrica do dispositivo, assegure que todos os cabos de alimentação estejam desconectados da fonte de alimentação. 2 1 Chapter 2. Safety information 15 16 Hardware Maintenance Manual 2 1 Chapter 2. Safety information 17 18 Hardware Maintenance Manual 2 1 Chapter 2. Safety information 19 DANGER Le courant électrique provenant de l’alimentation, du téléphone et des câbles de transmission peut présenter un danger. Pour éviter tout risque de choc électrique : v Ne manipulez aucun câble et n’effectuez aucune opération d’installation, d’entretien ou de reconfiguration de ce produit au cours d’un orage. v Branchez tous les cordons d’alimentation sur un socle de prise de courant correctement câblé et mis à la terre. v Branchez sur des socles de prise de courant correctement câblés tout équipement connecté à ce produit. v Lorsque cela est possible, n’utilisez qu’une seule main pour connecter ou déconnecter les câbles d’interface. v Ne mettez jamais un équipement sous tension en cas d’incendie ou d’inondation, ou en présence de dommages matériels. v Avant de retirer les carters de l’unité, mettez celle-ci hors tension et déconnectez ses cordons d’alimentation, ainsi que les câbles qui la relient aux réseaux, aux systèmes de télécommunication et aux modems (sauf instruction contraire mentionnée dans les procédures d’installation et de configuration). v Lorsque vous installez, que vous déplacez, ou que vous manipulez le présent produit ou des périphériques qui lui sont raccordés, reportez-vous aux instructions ci-dessous pour connecter et déconnecter les différents cordons. Connexion Déconnexion 1. Mettez les unités HORS TENSION. 1. Mettez les unités HORS TENSION. 2. Commencez par brancher tous les cordons sur les unités. 2. Débranchez les cordons d’alimentation des prises. 3. Branchez les câbles d’interface sur des connecteurs. 3. Débranchez les câbles d’interface des connecteurs. 4. Branchez les cordons d’alimentation sur des prises. 4. Débranchez tous les câbles des unités. 5. Mettez les unités SOUS TENSION. 20 Hardware Maintenance Manual ATTENTION: Remplacer la pile au lithium usagée par une pile de référence identique exclusivement, (référence 33F8354), ou suivre les instructions du fabricant qui en définit les équivalences. Si votre système est doté d’un module contenant une pile au lithium, vous devez le remplacer uniquement par un module identique, produit par le même fabricant. La pile contient du lithium et peut exploser en cas de mauvaise utilisation, de mauvaise manipulation ou de mise au rebut inappropriée. Ne pas : v la jeter à l’eau, v l’exposer à des températures supérieures à 100°C, v chercher à la réparer ou à la démonter. Ne pas mettre la pile à la poubelle. Pour la mise au rebut, se reporter à la réglementation en vigueur. ATTENTION: Si des produits à laser (tels que des unités de CD-ROM, de DVD-ROM, des unités à fibres optiques, ou des émetteurs) sont installés, prenez connaissance des informations suivantes : v Ne retirez pas le carter. En ouvrant l’unité de CD-ROM ou de DVD-ROM, vous vous exposez au rayonnement dangereux du laser. Aucune pièce de l’unité n’est réparable. v Pour éviter tout risque d’exposition au rayon laser, respectez les consignes de réglage et d’utilisation des commandes, ainsi que les procédures décrites dans le présent manuel. DANGER Certains produits à laser contiennent une diode à laser intégrée de classe 3A ou 3B. Prenez connaissance des informations suivantes: Rayonnement laser lorsque le carter est ouvert. Evitez toute expositiondirecte au rayon laser. Evitez de regarder fixement le faisceau ou del’observer à l’aide d’instruments optiques. Chapter 2. Safety information 21 ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) ATTENTION: Soulevez la machine avec précaution. ATTENTION: L’interrupteur de contrôle d’alimentation de l’unité et l’interrupteur dubloc d’alimentation ne coupent pas le courant électrique alimentantl’unité. En outre, le système peut être équipé de plusieurs cordonsd’alimentation. Pour mettre l’unité hors tension, vous devez déconnectertous les cordons de la source d’alimentation. 2 1 22 Hardware Maintenance Manual VORSICHT An Netz-, Telefon- und Datenleitungen können gefährliche Spannungen anliegen. Aus Sicherheitsgründen: v Bei Gewitter an diesem Gerät keine Kabel anschließen oder lösen. Ferner keine Installations-, Wartungs- oder Rekonfigurationsarbeiten durchführen. v Gerät nur an eine Schutzkontaktsteckdose mit ordnungsgemäß geerdetem Schutzkontakt anschließen. v Alle angeschlossenen Geräte ebenfalls an Schutzkontaktsteckdosen mit ordnungsgemäß geerdetem Schutzkontakt anschließen. v Die Signalkabel nach Möglichkeit einhändig anschließen oder lösen, um einen Stromschlag durch Berühren von Oberflächen mit unterschiedlichem elektrischem Potenzial zu vermeiden. v Geräte niemals einschalten, wenn Hinweise auf Feuer, Wasser oder Gebäudeschäden vorliegen. v Die Verbindung zu den angeschlossenen Netzkabeln, Telekommunikationssystemen, Netzwerken und Modems ist vor dem Öffnen des Gehäuses zu unterbrechen, sofern in den Installations- und Konfigurationsprozeduren keine anders lautenden Anweisungen enthalten sind. v Zum Installieren, Transportieren und Öffnen der Abdeckungen des Computers oder der angeschlossenen Einheiten die Kabel gemäß der folgenden Tabelle anschließen und abziehen. Zum Anschließen der Kabel gehen Sie wie folgt vor Zum Abziehen der Kabel gehen Sie wie folgt vor 1. Schalten Sie alle Einheiten AUS. 1. Schalten Sie alle Einheiten AUS. 2. Schließen Sie erst alle Kabel an die Einheiten an. 2. Ziehen Sie zuerst alle Netzkabel aus den Netzsteckdosen. 3. Schließen Sie die Signalkabel an die Buchsen an. 3. Ziehen Sie die Signalkabel aus den Buchsen. 4. Schließen Sie die Netzkabel an die Steckdose an. 4. Ziehen Sie alle Kabel von den Einheiten ab. 5. Schalten Sie die Einheit EIN. Chapter 2. Safety information 23 CAUTION: Eine verbrauchte Lithiumbatterie nur durch eine Batterie mit der Teilenummer 33F8354 oder eine gleichwertige, vom Hersteller empfohlene Batterie ersetzen. Enthält das System ein Modul mit einer Lithiumbatterie, dieses nur durch ein Modul desselben Typs und von demselben Hersteller ersetzen. Die Batterie enthält Lithium und kann bei unsachgemäßer Verwendung, Handhabung oder Entsorgung explodieren. Die Batterie nicht: v mit Wasser in Berührung bringen. v über 100 C erhitzen. v reparieren oder zerlegen. Die örtlichen Bestimmungen für die Entsorgung von Sondermüll beachten. ACHTUNG: Bei der Installation von Lasergeräten (wie CD-ROM-Laufwerken, DVDaufwerken, Einheiten mit Lichtwellenleitertechnik oder Sendern) Folgendes beachten: v Die Abdeckungen nicht entfernen. Durch Entfernen der Abdeckungen des Lasergeräts können gefährliche Laserstrahlungen freigesetzt werden. Das Gerät enthält keine zu wartenden Teile. v Werden Steuerelemente, Einstellungen oder Durchführungen von Prozeduren anders als hier angegeben verwendet, kann gefährliche Laserstrahlung auftreten. VORSICHT Einige Lasergeräte enthalten eine Laserdiode der Klasse 3A oder 3B. Beachten Sie Folgendes: Laserstrahlung bei geöffneter Verkleidung. Nicht in den Strahl blicken. Keine Lupen oder Spiegel verwenden. Strahlungsbereich meiden. 24 Hardware Maintenance Manual ≥18 kg ≥32 kg ≥55 kg ACHTUNG: Arbeitsschutzrichtlinien beim Anheben der Maschine beachten. ACHTUNG: Mit dem Netzschalter an der Einheit und am Netzteil wird die Stromversorgung für die Einheit nicht unterbrochen. Die Einheit kann auch mit mehreren Netzkabeln ausgestattet sein. Um die Stromversorgung für die Einheit vollständig zu unterbrechen, müssen alle zum Gerät führenden Netzkabel vom Netz getrennt werden. 2 1 Chapter 2. Safety information 25 26 Hardware Maintenance Manual Chapter 2. Safety information 27 2 1 28 Hardware Maintenance Manual PERICOLO La corrente elettrica proveniente dai cavi di alimentazione, del telefono e di comunicazione può essere pericolosa. Per evitare il rischio di scosse elettriche: v Non collegare o scollegare qualsiasi cavo oppure effettuare l’installazione, la manutenzione o la riconfigurazione del prodotto durante un temporale. v Collegare tutti i fili elettrici a una presa di alimentazione correttamente cablata e dotata di messa a terra. v Collegare alle prese elettriche appropriate tutte le apparecchiature che verranno utilizzate per questo prodotto. v Se possibile, utilizzare solo una mano per collegare o scollegare i cavi di segnale. v Non accendere assolutamente apparecchiature in presenza di incendi, perdite d’acqua o danno strutturale. v Scollegare i cavi di alimentazione, i sistemi di telecomunicazione, le reti e il modem prima di aprire i coperchi del dispositivo, salvo istruzioni contrarie relative alle procedure di installazione e configurazione. v Collegare e scollegare i cavi come descritto nella seguente tabella quando vengono effettuate operazioni di installazione, spostamento o apertura dei coperchi di questo prodotto o delle unità collegate. Per collegarsi Per scollegarsi 1. SPEGNERE le apparecchiature. 1. SPEGNERE le apparecchiature. 2. Innanzitutto, collegare tutti i cavi alle unità. 2. Innanzitutto, rimuovere i cavi di alimentazione dalla presa. 3. Collegare i cavi di segnale ai connettori. 3. Rimuovere i cavi di segnale dai connettori. 4. Collegare i cavi di alimentazione alla presa. 4. Rimuovere tutti i cavi dalle unità. 5. Accendere l’unità. Chapter 2. Safety information 29 ATTENZIONE: Quando si sostituisce la batteria al litio, utilizzare solo il Numero parte 33F8354 o un tipo di batteria equivalente consigliato dal produttore. Se sul sistema è presente un modulo che contiene una batteria al litio, sostituirlo solo con un tipo di modulo dello stesso tipo della stessa casa di produzione. La batteria contiene litio e può esplodere se usata, maneggiata o smaltita in modo non corretto. Non: v Gettare o immergere la batteria nell’acqua v Riscaldarla ad una temperatura superiore ai 100 gradi C (212 gradi F) v Smontarla, ricaricarla o tentare di ripararla Le batterie usate vanno smaltite in accordo alla normativa in vigore (DPR 915/82 e successive disposizioni e disposizioni locali). ATTENZIONE: Quando vengono installati prodotti laser (quali CD-ROM, unità DVD-ROM, unità a fibre ottiche o trasmittenti), tener presente quanto segue: v Non rimuovere gli sportelli. L’apertura di un’unità laser può determinare l’esposizione a radiazioni laser pericolose. All’interno dell’unità non vi sono parti su cui effettuare l’assistenza tecnica. v L’utilizzo di controlli, regolazioni o l’esecuzione di procedure non descritti nel presente manuale possono provocare l’esposizione a radiazioni pericolose. PERICOLO Alcune unità laser contengono un diodo laser di Classe 3A o Classe 3B. Tener presente quanto segue: Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo direttamente con strumenti ottici ed evitare l’esposizione al fascio. 30 Hardware Maintenance Manual ≥18 kg ≥32 kg ≥55 kg ATTENZIONE: Prestare attenzione nel sollevare l’apparecchiatura. ATTENZIONE: Il pulsante di controllo dell’alimentazione presente sull’unità e l’interruttore dell’alimentatore non disattivano l’alimentazione corrente fornita all’unità. E’ possibile che l’unità disponga di più cavi di alimentazione. Per disattivare l’alimentazione dall’unità, accertarsi che tutti i cavi di alimentazione siano scollegati dalla fonte di alimentazione. 2 1 Chapter 2. Safety information 31 32 Hardware Maintenance Manual 2 1 Chapter 2. Safety information 33 PELIGRO La corriente eléctrica procedente de cables de alimentación, teléfonos y cables de comunicación puede ser peligrosa. Para evitar el riesgo de descarga eléctrica: v No conecte ni desconecte los cables ni realice ninguna tarea de instalación, mantenimiento o reconfiguración de este producto durante una tormenta eléctrica. v Conecte todos los cables de alimentación a tomas de corriente debidamente cableadas y conectadas a tierra. v Cualquier equipo que se conecte a este producto también debe conectarse a tomas de corriente debidamente cableadas. v Siempre que sea posible, utilice una sola mano para conectar o desconectar los cables de señal. v No encienda nunca un equipo cuando hay señales de fuego, agua o daños estructurales. v Desconecte los cables de alimentación, los sistemas de telecomunicaciones, las redes y los módems conectados antes de abrir las cubiertas de los dispositivos, a menos que se indique lo contrario en los procedimientos de instalación y configuración. v Conecte y desconecte los cables, como se describe en la tabla siguiente, cuando instale, mueva o abra las cubiertas de este producto o de los dispositivos conectados. Para conectar Para desconectar 1. APÁGUELO todo. 1. APÁGUELO todo. 2. En primer lugar, conecte todos los cables a los dispositivos. 2. En primer lugar, desenchufe los cables de alimentación de las tomas de corriente. 3. Conecte los cables de señal a los conectores. 3. Desconecte los cables de señal de los conectores. 4. Enchufe los cables de alimentación a las 4. Desconecte todos los cables de los tomas de corriente. dispositivos. 5. Encienda el dispositivo. 34 Hardware Maintenance Manual PRECAUCIÓN: Cuando sustituya una batería de litio, utilice solamente una batería número de pieza 33F8354 u otra de tipo equivalente recomendada por el fabricante. Si su sistema dispone de un módulo que contiene una batería de litio, reemplácelo sólo con el mismo tipo de módulo, del mismo fabricante. La batería contiene litio y puede explotar si no se utiliza, manipula o desecha correctamente. No debe: v Arrojarla al agua o sumergirla en ella v Exponerla a temperaturas superiores a 100°C (212°F) v Repararla o desmontarla Deshágase de la batería según especifiquen las leyes o normas locales. PRECAUCIÓN: Cuando haya productos láser (como unidades de CD-ROM, unidades de DVD, dispositivos de fibra óptica o transmisores) instalados, tenga en cuenta lo siguiente: v No quite las cubiertas. Si quita las cubiertas del producto láser, podría quedar expuesto a radiación láser peligrosa. Dentro del dispositivo no existe ninguna pieza que requiera servicio técnico. v Si usa controles o ajustes o realiza procedimientos que no sean los especificados aquí, podría exponerse a radiaciones peligrosas. PELIGRO Algunos productos láser tienen incorporado un diodo láser de clase 3A o clase 3B. Tenga en cuenta lo siguiente: Cuando se abre, queda expuesto a radiación láser. No mire directamente al rayo láser, ni siquiera con instrumentos ópticos, y evite exponerse directamente al rayo láser. Chapter 2. Safety information 35 ≥18 kg ≥32 kg ≥55 kg PRECAUCIÓN: Adopte procedimientos seguros al levantar el equipo. PRECAUCIÓN: El botón de control de alimentación del dispositivo y el interruptor de alimentación de la fuente de alimentación no desconectan la corriente eléctrica suministrada al dispositivo. Además, el dispositivo podría tener más de un cable de alimentación. Para suprimir toda la corriente eléctrica del dispositivo, asegúrese de que todos los cables de alimentación estén desconectados de la toma de corriente. 2 1 36 Hardware Maintenance Manual Chapter 3. General information This chapter provides general information that applies to all machine types supported by this publication. The ThinkVantage™ Productivity Center program Use the ThinkVantage Productivity Center program for general information about the use, operation, and maintenance of the computer. The ThinkVantage Productivity Center program also contains information to help solve problems and get repair service or other technical assistance. The ThinkVantage Productivity Center program is preinstalled on most ThinkCentre products. Additional information resources If you have Internet access, the most up-to-date information for the computer is available from the World Wide Web. You can find the following information: v Customer Replaceable Unit (CRU) removal and installation instructions v Publications v Troubleshooting information v Parts information v Downloads and drivers v Links to other useful sources of information To access this information, point your browser to http://www.lenovo.com/ support/. © Copyright Lenovo 2006, 2007 37 Specifications This section lists the physical specifications for your computer. Dimensions Width: 275 mm (10.83 in.) Height: 81 mm (3.19 in.) Depth: 242 mm (9.53 in.) Weight Note: The weight does not include the power supply or any external cables. Minimum configuration as shipped: 3.27 kg (7.2 lbs) Maximum configuration: 3.72 kg (8.2 lbs) Environment Air temperature: Operating at 0 - 3000 ft (914.4 m): 10° to 35°C (50° to 95°F) Non-operating: -40° to 60°C (-40° to 140°F) Maximum altitude: 3000 ft (914.4 m) Note: The maximum altitude, 3000 ft. (914.4 m), is the maximum altitude at which the specified air temperatures apply. At higher altitudes, the maximum air temperatures are lower than those specified. Humidity (non-condensing): Operating: 10% to 80% Non-operating: 10% to 90% Electrical input Input voltage: Low range: Minimum: 100 V ac Maximum: 127 V ac Input frequency range: 50/60 Hz High range: Minimum: 200 V ac Maximum: 240 V ac Input frequency range: 50/60 Hz Input kilovolt-amperes (kVA) (approximate): Minimum configuration as shipped: 0.05 kVA (all machine types) Maximum configuration: 0.12 kVA (Machine Types 6417, 6418, 6449, and 6453) Note: Power consumption and heat output vary depending on the number and type of optional features installed and the power-management optional features in use. 38 Hardware Maintenance Manual Chapter 4. General Checkout Attention The drives in the computer you are servicing might have been rearranged or the drive startup sequence changed. Be extremely careful during write operations such as copying, saving, or formatting. Data or programs can be overwritten if you select an incorrect drive. General error messages appear if a problem or conflict is found by an application program, the operating system, or both. For an explanation of these messages, refer to the information supplied with that software package. Before replacing any FRUs, ensure that the latest level of BIOS is installed on the system. A down-level BIOS might cause false errors and unnecessary replacement of the system board. For more information on how to determine and obtain the latest level BIOS, see “BIOS levels” on page 131. Use the following procedure to help determine the cause of the problem: Power-off the computer and all external devices. Check all cables and power cords. Set all display controls to the middle position. Power-on all external devices. Power-on the computer. v Look for displayed error codes v Listen for beep codes v Look for readable instructions or a main menu on the display. If you did not receive the correct response, proceed to step 6. If you do receive the correct response, run the diagnostics. .See “Running diagnostics from the CD or diskettes” on page 45. 6. Look at the following conditions and follow the instructions: v If you hear beep codes during POST, go to “Beep symptoms” on page 74. v If the computer displays a POST error, go to “POST error codes” on page 75. v If the computer hangs and no error is displayed, go to “Checking for power problems.” 1. 2. 3. 4. 5. Checking for power problems If the computer does not turn on when the power switch is pressed, use the following procedure to help troubleshoot. 1. Press the power switch to turn on the computer. Check the power indicator LED next to the power switch. v If the LED is illuminated (on), the computer power is OK. Attempt to run the diagnostics. See “Running diagnostics from the CD or diskettes” on page 45. v If the LED is not illuminated (off), go to step 2 2. Check the status of the power indicator LED on the AC/DC power adapter. v If the LED is illuminated (on), go to step 7 on page 40. v If the LED is not illuminated (off), go to the next step 3 on page 40. © Copyright Lenovo 2006, 2007 39 3. Verify that the power cord is properly connected to an AC power outlet. 4. Verify that you are using a good AC power outlet. Plug another device into the outlet or contact the power company or supplier to verify that the outlet is working correctly . 5. Check the power cord continuity. 6. Replace the AC/DC power adapter. 7. Verify that the power cord from the AC/DC power adapter to the computer is properly connected. See “Connectors on the rear of the computer” on page 81. 8. Open the cover. See “Opening the cover” on page 84. 9. Check the Power switch/LED assembly connector on the system board. See “System board locations” on page 83. Reseat the cable from the Power switch/LED assembly to the system board. 10. Replace the power switch/LED assembly. 11. Replace the system board. See “Replacing the system board” on page 89. Problem determination tips Due to the variety of hardware and software combinations that can be encountered, use the following information to assist you in problem determination. If possible, have this information available when requesting assistance from Service Support and Engineering functions. v Machine type and model v Processor or hard disk upgrades v Failure symptom – Do diagnostics indicate a failure? – What, when, where, single, or multiple systems? – Is the failure repeatable? – Has this configuration ever worked? – If it has been working, what changes were made prior to it failing? – Is this the original reported failure? v Diagnostics version – Type and version level v Hardware configuration – Print (print screen) configuration currently in use – BIOS level v Operating system software – Type and version level Note: To eliminate confusion, identical systems are considered identical only if they: 1. Are the exact machine type and models 2. Have the same BIOS level 3. Have the same adapters/attachments in the same locations 4. Have the same address jumpers/terminators/cabling 5. Have the same software versions and levels 6. Have the same Diagnostic Diskettes (version) 7. Have the same configuration options set in the system 8. Have the same setup for the operating system control files 40 Hardware Maintenance Manual Comparing the configuration and software set-up between “working and non-working” systems will often lead to problem resolution. Chapter 4. General Checkout 41 42 Hardware Maintenance Manual Chapter 5. Diagnostics Diagnostic programs are used to test hardware components of your computer and report operating-system-controlled settings that can cause hardware failures. There are two diagnostic programs preinstalled on your computer to help you diagnose problems: v PC-Doctor for Windows (used when diagnosing problems while running the Windows operating system) v PC-Doctor for Windows PE (used when your Windows operating system will not start) Notes: 1. You can also download the latest version of the PC-Doctor for Windows and PC-Doctor for DOS diagnostic programs from http://www.lenovo.com/ support/. 2. If you are unable to isolate and repair the problem yourself by running the applicable version of PC-Doctor, click the Save Button in the PC-Doctor-log-file display. You will need to have all problem-related log files available when you speak to a Lenovo technical support representative. PC-Doctor for Windows PC-Doctor for Windows is a diagnostic program that works through the Windows operating system. The PC-Doctor for Windows diagnostic program enables you to view symptoms and solutions for computer problems, access the Lenovo troubleshooting center, update system drivers, and review system information. To run PC-Doctor for Windows, open the Start menu from the Windows desktop, select All Programs, select PC-Doctor for Windows, and click PC-Doctor for Windows. Follow the instructions on the screen. For additional information about running the diagnostic program, refer to the PC-Doctor for Windows help system. If you still suspect a problem after PC-Doctor for Windows runs successfully, run PC-Doctor for DOS or PC-Doctor for Windows PE to help you diagnose the computer problem. PC Doctor for Windows also has problem determination aids that determine software and usage problems. PC-Doctor for Windows PE The PC-Doctor for Windows PE diagnostic program is part of the Rescue and Recovery workspace on each Lenovo computer. Use PC-Doctor for Windows PE, if you are unable to start the Windows operating system or if PC-Doctor for Windows has not been successful in isolating a possible problem. Running diagnostics from the Rescue and Recovery workspace You can run the PC-Doctor for Windows PE diagnostic program from the Rescue and Recovery workspace. To run diagnostics from the Rescue and Recovery workspace, use the following procedure: © Copyright Lenovo 2006, 2007 43 1. Shut down the operating system and turn off the computer. 2. Repeatedly press and release the F11 key as you turn on the computer. 3. When you hear beeps or see a logo screen, stop pressing the F11 key. The Rescue and Recovery workspace opens. 4. From the Rescue and Recovery workspace, select Diagnose hardware. 5. The diagnostic program opens automatically. Select the diagnostic test you want to run. Press the F1 key for additional help. 6. Follow the instructions on the screen. Note: Rescue media includes PC-Doctor for Windows PE. For more information about rescue media, see the User Guide for the computer. PC-Doctor for DOS Use PC-Doctor for DOS, if you are unable to start the Windows operating system or if PC-Doctor for Windows has not been successful in isolating a possible problem. You can run PC-Doctor for DOS from a diagnostic CD image or diagnostic diskettes that have been created. Note: It is important to create a diagnostic CD image or diagnostic diskettes in case PC-Doctor for Windows PE cannot be run from the Rescue and Recovery workspace. Creating a diagnostic CD image To create a diagnostic CD image, download a self-starting bootable CD image (known as an .iso image) of the diagnostic program from http:// www.lenovo.com/support/. After you download the image, you can create the CD using any CD burning software. If the computer does not have a CD burner or you do not have Internet access, see “Creating diagnostic diskettes.” Creating diagnostic diskettes To create diagnostic diskettes, download the PC-Doctor for DOS diagnostic program from http://www.lenovo.com/support/ onto two blank, formatted diskettes. If you do not have Internet access, create the diagnostic diskettes using the following procedure: Note: You will need a diskette drive on the computer or a USB diskette drive to complete this procedure. 1. 2. 3. 4. Shut down the operating system and turn off the computer. If you are using a USB diskette drive, plug it into the computer. Repeatedly press and release the F11 key as you turn on the computer. When you hear beeps or see a logo screen, stop pressing the F11 key. The Rescue and Recovery workspace opens. Note: For some models, press the Esc key to enter Rescue and Recovery. 5. From the Rescue and Recovery workspace, select Create diagnostic disks. 6. Follow the instructions on the screen. 44 Hardware Maintenance Manual 7. When prompted, insert a blank, formatted diskette into the diskette drive and continue to follow the instructions on the screen. 8. When the operation is complete, remove the diskette and click Quit. 9. Insert another blank, formatted diskette into the diskette drive and continue to follow the instructions on the screen. 10. When the operation is complete, remove the diskette and click Quit. Running diagnostics from the CD or diskettes To run diagnostics from the diagnostic CD image or diagnostic diskettes that you created, use the following procedure: 1. Make sure the computer is turned off. 2. If you are running diagnostics from diskettes using a USB diskette drive, plug in the USB device. 3. Insert the CD into the optical drive or the first diagnostic diskette into the diskette drive. 4. Restart the computer. Note: If the diagnostic program does not start, you might not have your optical drive or diskette drive set as a startable device. See “Selecting a startup device” on page 50 for instructions on how to change the startup device. 5. When the diagnostics program opens, follow the instructions on the screen. Note: If you are running diagnostics from a diskette, when prompted, remove the first diskette and insert the second diskette. 6. When the program finishes, be sure to remove the CD or diskette from the drive. 7. Select the diagnostic test you want to run. Press the F1 key for additional help. Navigating through the diagnostics programs Use the cursor movement keys to navigate within the menus. v The Enter key is used to select a menu item. v The Esc key is used to back up to the previous menu. v For online help select F1. Running tests There are four ways to run the diagnostic tests. v Using the cursor movement keys, highlight Run Normal Test or Run Quick Test from the Diagnostics menu and then press Enter. This automatically runs a pre-defined group of tests from each test category. Run Normal Test runs a more extensive set of tests than does Run Quick Test and takes longer to complete. v Press F5 to automatically run all selected tests in all categories. v From within a test category, press Ctrl-Enter to automatically run only the selected tests in that category. v Using the cursor movement keys, highlight a single test within a test category, and then press Enter. This runs only that test. Press Esc at any time to stop the testing process. Chapter 5. Diagnostics 45 Test results (N/A, PASSED, FAILED, ABORTED) are displayed in the field beside the test description and in the test log. See “Viewing the test log” on page 47. To 1. 2. 3. select one or more tests, use the following procedure. Open the corresponding test category. Using the cursor movement keys, highlight the desired test. Press the space bar. A selected test is marked by >>. Pressing the space bar again de-selects a test and removes the >>. 4. Repeat steps 2 and 3 above to select all desired tests. Test results Diagnostics test results produce the following error code format: Function Code Failure Type DeviceID Date ChkDigits Text v Function Code: Represents the feature or function within the PC. v Failure Type: Represents the type of error encountered. v DeviceID: Contains the component’s unit-ID which corresponds to either a fixed disk drive, removable media drive, processor, specific RIMM, or a device on the PCI bus. v Date: Contains the date when the diagnostic test was run. The date is retrieved from CMOS and displayed using the YYYYMMDD format. v ChkDigits: Contains a 2-digit check-digit value to ensure the following: – Diagnostics were run on the specified date. – Diagnostics were run on the specified computer. – The diagnostic error code is recorded correctly. v Text: Description of the error. Note: See “Diagnostic error codes” on page 54 for error code listings. Quick and Full erase - hard drive The diagnostics program offers two hard drive format utilities: v Quick Erase Hard Drive v Full Erase Hard Drive The Quick Erase Hard Drive provides a DOS utility that performs the following: v Destroys the Master Boot Record (MBR) on the hard drive. v Destroys all copies of the FAT Table on all partitions (both the master and backup). v Destroys the partition table. v Provides messages that warn the user that this is a non-recoverable process. 46 Hardware Maintenance Manual The Full Erase Hard Drive provides a DOS utility that performs the following: v Performs all the steps in Quick Erase. v Provides a DOS utility that writes random data to all sectors of the hard drive. v Provides an estimate of time to completion along with a visual representation of completion status. v Provides messages that warn the user about non-recoverable process. Important: Make sure that all data is backed up before using the Quick or Full Erase functions. To select the Quick Erase or Full Erase Hard Drive utility, use the following procedure: 1. Select the UTILITY option on the toolbar and press Enter. 2. Select either the QUICK ERASE or FULL ERASE HARD DISK option and follow the instructions. Viewing the test log Errors reported by the diagnostic test will be displayed by the program as a failed test. To view details of a failure or to view a list of test results, use the following procedure from any test category screen: 1. Press F3 to activate the log file. 2. Press F3 again to save the file to diskette or press F2 to print the file. Chapter 5. Diagnostics 47 48 Hardware Maintenance Manual Chapter 6. Using the Setup Utility The Setup Utility program is used to view and change the configuration settings of the computer, regardless of which operating system you are using. However, the operating-system settings might override any similar settings in the Setup Utility program. Starting the Setup Utility program To start the Setup Utility program, do the following: 1. If the computer is already on when you start this procedure, shut down the operating system and turn off the computer. 2. Press and hold the F1 key then turn on the computer. When you hear multiple beeps, release the F1 key. Notes: a. If you are using a USB keyboard and the Setup Utility program does not display using this method, repeatedly press and release the F1 key rather than leaving it pressed when turning on the computer. b. If a user password or an administrator password has been set, the Setup Utility program menu is not displayed until you type your password. For more information, see “Using passwords.” The Setup Utility might start automatically when POST detects that hardware has been removed or new hardware has been installed in the computer. Viewing and changing settings The Setup Utility program menu lists items that identify system configuration topics. To view or change settings, see “Starting the Setup Utility program.” When working with the Setup Utility program menu, you must use the keyboard. The keys used to perform various tasks are displayed at the bottom of each screen. Using passwords By using the Setup Utility program, you can set passwords to prevent unauthorized persons from gaining access to the computer and data. See “Starting the Setup Utility program.” The following types of passwords are available: v User Password v Administrator Password You do not have to set any passwords to use the computer. However, if you decide to set any passwords, read the following sections. Password considerations A password can be any combination of up to twelve characters (a-z and 0-9) and symbols. For security reasons, it is a good idea to use a strong password that cannot be easily compromised. Passwords should adhere to the following rules: v Have at least eight characters in length v Contain at least one alphabetic character and one numeric character © Copyright Lenovo 2006, 2007 49 v v v v Setup Utility program and hard disk drive passwords are not case sensitive Not be your name or your user name Not be a common word or a common name Be significantly different from your previous password User Password When a User Password is set, the computer cannot be used until a valid password is typed from the keyboard. Administrator Password When an Administrator Password is set, it deters unauthorized persons from changing configuration settings. If you are responsible for maintaining the settings of several computers, you might want to set an Administrator Password. After you set an Administrator Password, a password prompt is displayed each time you try to access the Setup Utility program. If both the user and administrator passwords are set, you can type either password. However, to change any configuration settings, you must use your administrator password. Setting, changing, and deleting a password To set, change, or delete a password, do the following: Note: A password can be any combination of up to twelve characters (A- Z, a-z, and 0-9). For more information, see “Password considerations” on page 49. 1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 49). 2. From the Setup Utility program menu, select Security. 3. Select Set Passwords. Read the information displayed on the right side of the screen. Selecting a startup device If the computer does not start up (boot) from a device such as the CD-ROM, diskette, or hard disk as expected, use one of the following procedures to select a startup device. Selecting a temporary startup device Use this procedure to startup from any boot device. Note: Not all CDs, hard disks, and diskettes are bootable. 1. Turn off the computer. 2. Press and hold the F12 key then turn on the computer. When the Startup Device Menu appears, release the F12 key. Note: If you are using a USB keyboard and the Startup Device Menu does not display using this method, repeatedly press and release the F12 key rather than leaving it pressed when turning on the computer. 3. Select the desired startup device from the Startup Device Menu and press Enter to begin. 50 Hardware Maintenance Manual Note: Selecting a startup device from the Startup Device menu does not permanently change the startup sequence. Selecting or changing the startup device sequence To view or permanently change the configured startup device sequence, do the following: 1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 49). 2. Select Startup. 3. Select Startup Sequence. See the information displayed on the right side of the screen. 4. Select the devices for the Primary Startup Sequence, the Automatic Startup Sequence, and the Error Startup Sequence. 5. Select Exit from the Setup Utility menu and then Save Settings or Save and exit the Setup Utility. If you have changed these settings and want to return to the default settings, select Load Default Settings on the Exit menu. Advanced settings On some computer models the Advanced settings menu includes a setting to Enable/Disable HyperThreading. This feature works only with HyperThreading-aware operating systems, such as Microsoft Windows XP and Windows Vista™. The default setting for HyperThreading is Enabled. However, if you select Set Defaults and are using an operating system other than Windows XP or Windows Vista, the computer performance might be degraded. Therefore, you should always set HyperThreading to Disabled unless you are sure your operating system supports HyperThreading. Exiting from the Setup Utility program When you finish viewing or changing settings, press Esc to return to the Setup Utility program menu (you might have to press Esc several times). If you want to save the new settings, select Save & Exit Setup before you exit. Otherwise, your changes will not be saved. Chapter 6. Using the Setup Utility 51 52 Hardware Maintenance Manual Chapter 7. Symptom-to-FRU Index The Symptom-to-FRU index lists error symptoms and possible causes. The most likely cause is listed first. Always begin with Chapter 4, “General Checkout,” on page 39. This index can also be used to help you decide which FRUs to have available when servicing a computer. If you are unable to correct the problem using this index, go to “Undetermined problems” on page 78. Notes: v If you have both an error message and an incorrect audio response, diagnose the error message first. v If you cannot run the diagnostic tests or you get a diagnostic error code when running a test, but did receive a POST error message, diagnose the POST error message first. v If you did not receive any error message, look for a description of your error symptoms in the first part of this index. Hard disk drive boot error A hard disk drive boot error (error codes 1962 and I999030X) can have the following causes. Error FRU/Action The start-up drive is not in the boot sequence in configuration. Check the configuration and ensure the start-up drive is in the boot sequence. No operating system installed on the boot drive. Install an operating system on the boot drive. The boot sector on the start-up drive is corrupted. The drive must be formatted, do the following: 1. Attempt to back-up the data on the failing hard disk drive. 2. Using the operating systems programs, format the hard disk drive. The drive is defective. © Copyright Lenovo 2006, 2007 Replace the hard disk drive. 53 Diagnostic error codes Refer to the following diagnostic error codes when using the diagnostic tests. See “Running tests” on page 45 for the specific type for information about the Diagnostic programs. In the following index, X can represent any number. Diagnostic Error Code FRU/Action 000-000-XXX BIOS Test Passed No action 000-002-XXX BIOS Timeout 1. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 2. System board 000-024-XXX BIOS Addressing test failure 1. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 2. System board 000-025-XXX BIOS Checksum Value error 1. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 2. System board 000-026-XXX FLASH data error 1. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 2. System board 000-027-XXX BIOS Configuration/Setup error 1. Run Setup 2. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. System board 000-034-XXX BIOS Buffer Allocation failure 1. Reboot the system 2. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Run memory test 4. System board 000-035-XXX BIOS Reset Condition detected 1. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 2. System board 000-036-XXX BIOS Register error 1. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 2. System board 54 Hardware Maintenance Manual Diagnostic Error Code FRU/Action 000-038-XXX BIOS Extension failure 1. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 2. Adapter card 3. System board 000-039-XXX BIOS DMI data error 1. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 2. System board 000-195-XXX BIOS Test aborted by user Information only Re-start the test, if necessary 000-196-XXX BIOS test halt, error threshold exceeded 1. Press F3 to review the log file 000-197-XXX BIOS test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Re-start the test to reset the log file 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 000-198-XXX BIOS test aborted 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Flash the system and retest. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Go to “Undetermined problems” on page 78 000-199-XXX BIOS test failed, cause unknown 1. Go to “Undetermined problems” on page 78 2. Flash the system and re-test 3. Replace component under function test 000-250-XXX BIOS APM failure 1. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 2. System board 000-270-XXX BIOS ACPI failure 1. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 2. System board 001-000-XXX System Test Passed No action 001-00X-XXX System Error System board 001-01X-XXX System Error System board Chapter 7. Symptom-to-FRU Index 55 Diagnostic Error Code FRU/Action 001-024-XXX System Addressing test failure System board 001-025-XXX System Checksum Value error 1. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 2. System board 001-026-XXX System FLASH data error 1. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 2. System board 001-027-XXX System Configuration/Setup error 1. Run Setup 2. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. System board 001-032-XXX System Device Controller failure System board 001-034-XXX System Device Buffer Allocation failure 1. Reboot the system 2. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Run memory test 4. System board 001-035-XXX System Device Reset condition detected System board 001-036-XXX System Register error System board 001-038-XXX System Extension failure 1. Adapter card 001-039-XXX System DMI data structure error 1. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 2. System board 2. System board 56 001-040-XXX System IRQ failure 1. Power-off/on system and re-test 001-041-XXX System DMA failure 1. Power-off/on system and re-test 001-195-XXX System Test aborted by user Information only Re-start the test, if necessary 001-196-XXX System test halt, error threshold exceeded 1. Press F3 to review the log file Hardware Maintenance Manual 2. System board 2. System board 2. Re-start the test to reset the log file Diagnostic Error Code FRU/Action 001-197-XXX System test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 001-198-XXX System test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Flash the system and retest. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Go to “Undetermined problems” on page 78 001-199-XXX System test failed, cause unknown 1. Go to “Undetermined problems” on page 78 2. Flash the system and re-test 3. Replace component under function test 001-250-XXX System ECC error System board 001-254-XXX 001-255-XXX 001-256-XXX 001-257-XXX System DMA error System board 001-260-XXX 001-264-XXX System IRQ error System board 001-268-XXX System IRQ1 failure 1. Device on IRQ1 001-269-XXX System IRQ2 failure 1. Device on IRQ2 001-270-XXX System IRQ3 failure 1. Device on IRQ3 001-271-XXX System IRQ4 failure 1. Device on IRQ4 001-272-XXX System IRQ5 failure 1. Device on IRQ5 001-273-XXX System IRQ6 (diskette drive) failure 1. Diskette Cable 001-274-XXX System IRQ7 failure 1. Device on IRQ7 2. System board 2. System board 2. System board 2. System board 2. System board 2. Diskette drive 3. System board 2. System board Chapter 7. Symptom-to-FRU Index 57 Diagnostic Error Code FRU/Action 001-275-XXX System IRQ8 failure 1. Device on IRQ8 001-276-XXX System IRQ9 failure 1. Device on IRQ9 001-277-XXX System IRQ10 failure 1. Device on IRQ10 001-278-XXX System IRQ11 failure 1. Device on IRQ11 001-279-XXX System IRQ12 failure 1. Device on IRQ12 001-280-XXX System IRQ13 failure 1. Device on IRQ13 001-281-XXX System IRQ14 (hard disk drive) failure 1. Hard disk drive cable 001-282-XXX System IRQ15 failure 1. Device on IRQ15 001-286-XXX 001-287-XXX 001-288-XXX System Timer failure System board 001-292-XXX System CMOS RAM error 1. Run Setup and re-test 001-293-XXX System CMOS Battery 1. CMOS Battery 001-298-XXX System RTC date/time update failure 1. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 2. System board 2. System board 2. System board 2. System board 2. System board 2. System board 2. Hard disk drive 3. System board 2. System board 2. System board 2. System board 2. System board 001-299-XXX System RTC periodic interrupt failure System board 001-300-XXX System RTC Alarm failure System board 001-301-XXX System RTC Century byte error 1. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 2. System board 58 005-000-XXX Video Test Passed No action 005-00X-XXX Video error 1. Video card, if installed Hardware Maintenance Manual 2. System board Diagnostic Error Code FRU/Action 005-010-XXX 005-011-XXX 005-012-XXX 005-013-XXX Video Signal failure 1. Video card, if installed 005-016-XXX Video Simple Pattern test failure 1. Video Ram 005-024-XXX Video Addressing test failure 1. Video card, if installed 005-025-XXX Video Checksum Value error 1. Video card, if installed 005-027-XXX Video Configuration/Setup error 1. Run Setup 2. System board 2. Video card, if installed 3. System board 2. System board 2. System board 2. Video drivers update 3. Video card, if installed 4. System board 005-031-XXX Video Device Cable failure 1. Video cable 2. Monitor 3. Video card, if installed 4. System board 005-032-XXX Video Device Controller failure 1. Video card, if installed 005-036-XXX Video Register error 1. Video card, if installed 005-038-XXX System BIOS extension failure 1. Video card, if installed 005-040-XXX Video IRQ failure 1. Video card, if installed 005-195-XXX Video Test aborted by user Information only Re-start the test, if necessary 005-196-XXX Video test halt, error threshold exceeded 1. Press F3 to review the log file 005-197-XXX Video test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. System board 2. System board 2. System board 2. System board 2. Re-start the test to reset the log file 2. Re-run test 3. Replace the component called out in warning statement 4. Replace the component under test Chapter 7. Symptom-to-FRU Index 59 Diagnostic Error Code FRU/Action 005-198-XXX Video test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Go to “Undetermined problems” on page 78 005-199-XXX Video test failed, cause unknown 1. Go to “Undetermined problems” on page 78 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Replace component under function test 005-2XX-XXX 005-3XX-XXX Video subsystem error 1. Video card, if installed 006-000-XXX Diskette interface Test Passed No action 006-0XX-XXX Diskette interface error 1. Diskette drive Cable 2. System board 2. Diskette drive 3. System board 006-195-XXX Diskette interface Test aborted by user Information only Re-start the test, if necessary 006-196-XXX Diskette interface test halt, error threshold exceeded 1. Press F3 to review the log file 006-197-XXX Diskette interface test warning 1. If a component is called out, make sure it is connected and/or enabled 2. Re-start the test to reset the log file 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 006-198-XXX Diskette interface test aborted 1. If a component is called out, make sure it is connected and/or enabled 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Go to “Undetermined problems” on page 78 006-199-XXX 1. Go to “Undetermined problems” on page Diskette interface test failed, cause unknown 78 2. Flash the system and re-test 3. Replace component under function test 006-25X-XXX Diskette interface Error 1. Diskette drive cable 2. Diskette drive 3. System board 60 Hardware Maintenance Manual Diagnostic Error Code FRU/Action 015-000-XXX USB port Interface Test Passed No action 015-001-XXX USB port Presence 1. Remove USB device(s) and re-test 015-002-XXX USB port Timeout 1. Remove USB device(s) and re-test 015-015-XXX USB port External Loopback failure 1. Remove USB device(s) and re-test 015-027-XXX USB port Configuration/Setup error 1. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 2. System board 2. System board 2. System board 2. System board 015-032-XXX USB port Device Controller failure System board 015-034-XXX USB port buffer allocation failure 1. Reboot the system 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Run memory test 4. System board 015-035-XXX USB port Reset condition detected 1. Remove USB device(s) and re-test 015-036-XXX USB port Register error System board 015-040-XXX USB port IRQ failure 1. Run setup and check for conflicts 2. System board 2. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. System board 015-195-XXX USB port Test aborted by user Information only Re-start the test, if necessary 015-196-XXX USB port test halt, error threshold exceeded 1. Press F3 to review the log file 015-197-XXX USB port test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Re-start the test to reset the log file 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test Chapter 7. Symptom-to-FRU Index 61 Diagnostic Error Code FRU/Action 015-198-XXX USB port test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Go to “Undetermined problems” on page 78 015-199-XXX USB port test failed, cause unknown 1. Go to “Undetermined problems” on page 78 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Replace component under function test 018-000-XXX PCI Card Test Passed No action 018-0XX-XXX PCI Card Failure 1. Riser card, if installed 018-195-XXX PCI Card Test aborted by user 1. PCI card 018-196-XXX PCI Card test halt, error threshold exceeded 1. Press F3 to review the log file 018-197-XXX PCI Card test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. System board 2. Information only Re-start the test, if necessary 2. Re-start the test to reset the log file 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 018-198-XXX PCI Card test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Go to “Undetermined problems” on page 78 018-199-XXX PCI Card test failed, cause unknown 1. Go to “Undetermined problems” on page 78 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Replace component under function test 62 Hardware Maintenance Manual Diagnostic Error Code FRU/Action 018-250-XXX PCI Card Services error 1. PCI card 2. Riser card, if installed 3. System board 020-000-XXX PCI Interface Test Passed No action 020-0XX-XXX PCI Interface error 1. PCI card 2. Riser card, if installed 3. System board 020-195-XXX PCI Test aborted by user Information only Re-start the test, if necessary 020-196-XXX PCI test halt, error threshold exceeded 1. Press F3 to review the log file 020-197-XXX PCI test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Re-start the test to reset the log file 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 020-198-XXX PCI test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Go to “Undetermined problems” on page 78 020-199-XXX PCI test failed, cause unknown 1. Go to “Undetermined problems” on page 78 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Replace component under function test 020-262-XXX PCI system error 1. PCI card 2. Riser card, if installed 3. System board 025-000-XXX IDE interface Test Passed No action 025-00X-XXX 025-01X-XXX IDE interface failure 1. IDE signal cable 2. Check power supply voltages 3. Reseat IDE signal cable 4. IDE device 5. System board Chapter 7. Symptom-to-FRU Index 63 Diagnostic Error Code FRU/Action 025-027-XXX IDE interface Configuration/Setup error 1. IDE signal cable 2. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Reseat IDE signal cable 4. IDE device 5. System board 025-02X-XXX 025-03X-XXX 025-04X-XXX IDE Interface failure 1. IDE signal cable 2. Check AC/DC power adapter 3. Reseat IDE signal cable 4. IDE device 5. System board 025-195-XXX IDE interface Test aborted by user Information only Re-start the test, if necessary 025-196-XXX IDE interface test halt, error threshold exceeded 1. Press F3 to review the log file 025-197-XXX IDE interface test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Re-start the test to reset the log file 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 025-198-XXX IDE interface test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Go to “Undetermined problems” on page 78 025-199-XXX IDE interface test failed, cause unknown 1. Go to “Undetermined problems” on page 78 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Replace component under function test 030-000-XXX SCSI interface Test Passed No action 030-00X-XXX 030-01X-XXX SCSI interface failure 1. SCSI signal cable 2. Check AC/DC power adapter 3. SCSI device 4. SCSI adapter card, if installed 5. System board 64 Hardware Maintenance Manual Diagnostic Error Code FRU/Action 030-027-XXX SCSI interface Configuration/Setup error 1. SCSI signal cable 2. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. SCSI device 4. SCSI adapter card, if installed 5. System board 030-03X-XXX 030-04X-XXX SCSI interface error 1. SCSI signal cable 2. Check AC/DC power adapter 3. SCSI device 4. SCSI adapter card, if installed 5. System board 030-195-XXX SCSI interface Test aborted by user Information only Re-start the test, if necessary 030-196-XXX SCSI interface test halt, error threshold exceeded 1. Press F3 to review the log file 030-197-XXX SCSI interface test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Re-start the test to reset the log file 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 030-198-XXX SCSI interface test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Go to “Undetermined problems” on page 78 030-199-XXX SCSI interface test failed, cause unknown 1. Go to “Undetermined problems” on page 78 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Replace component under function test 035-000-XXX RAID interface Test Passed No action 035-0XX-XXX RAID interface Failure 1. RAID signal cable 2. RAID device 3. RAID adapter card, if installed 4. System board 035-195-XXX RAID interface Test aborted by user Information only Re-start the test, if necessary Chapter 7. Symptom-to-FRU Index 65 Diagnostic Error Code FRU/Action 035-196-XXX RAID interface test halt, error threshold exceeded 1. Press F3 to review the log file 035-197-XXX RAID interface test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Re-start the test to reset the log file 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 035-198-XXX RAID interface test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Go to “Undetermined problems” on page 78 035-199-XXX RAID interface test failed, cause unknown 1. See “Undetermined problems” on page 78 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Replace component under function test 071-000-XXX Audio port Interface Test Passed No action 071-00X-XXX 071-01X-XXX 071-02X-XXX Audio port error 1. Run Setup 2. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. System board 071-03X-XXX Audio port failure 1. Speakers 2. Microphone 3. Audio card, if installed 4. System board 071-04X-XXX Audio port failure 1. Run Setup 2. Audio card, if installed 3. System board 66 071-195-XXX Audio port Test aborted by user Information only Re-start the test, if necessary 071-196-XXX Audio port test halt, error threshold exceeded 1. Press F3 to review the log file Hardware Maintenance Manual 2. Re-start the test to reset the log file Diagnostic Error Code FRU/Action 071-197-XXX Audio port test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 071-198-XXX Audio port test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Go to “Undetermined problems” on page 78 071-199-XXX Audio port test failed, cause unknown 1. See “Undetermined problems” on page 78 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Replace component under function test 071-25X-XXX Audio port failure 1. Speakers 2. Audio card, if installed 3. System board 080-000-XXX Game Port interface Test Passed No action 080-XXX-XXX Game Port interface Error 1. Remove the game port device and re-test the system 080-195-XXX Game Port interface Test aborted by user Information only Re-start the test, if necessary 080-196-XXX 1. Press F3 to review the log file Game Port interface test halt, error threshold 2. Re-start the test to reset the log file exceeded 080-197-XXX Game Port interface test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test Chapter 7. Symptom-to-FRU Index 67 Diagnostic Error Code FRU/Action 080-198-XXX Game Port interface test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Go to “Undetermined problems” on page 78 080-199-XXX Game Port interface test failed, cause unknown 1. See “Undetermined problems” on page 78 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Replace component under function test 086-000-XXX Mouse Port interface Test Passed No action 086-001-XXX Mouse Port interface Presence 1. Mouse 086-032-XXX Mouse Port interface Device controller failure 1. Mouse 086-035-XXX Mouse Port interface Reset 1. Mouse 086-040-XXX Mouse Port interface IRQ failure 1. Run Setup 2. System board 2. System board 2. System board 2. Mouse 3. System board 086-195-XXX Mouse Port interface Test aborted by user Information only Re-start the test, if necessary 086-196-XXX Mouse Port interface test halt, error threshold exceeded 1. Press F3 to review the log file 086-197-XXX Mouse Port interface test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Re-start the test to reset the log file 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 086-198-XXX Mouse Port interface test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Go to “Undetermined problems” on page 78 68 Hardware Maintenance Manual Diagnostic Error Code FRU/Action 086-199-XXX Mouse Port interface test failed, cause unknown 1. See “Undetermined problems” on page 78 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Replace component under function test 089-000-XXX Microprocessor Test Passed No action 089-XXX-XXX Microprocessor failure 1. Microprocessor(s) 089-195-XXX Microprocessor Test aborted by user Information only Re-start the test, if necessary 089-196-XXX Microprocessor test halt, error threshold exceeded 1. Press F3 to review the log file 089-197-XXX Microprocessor test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. System board 2. Re-start the test to reset the log file 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 089-198-XXX Microprocessor test aborted 1. Flash the system. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 2. Go to “Undetermined problems” on page 78 089-199-XXX Microprocessor test failed, cause unknown 1. See “Undetermined problems” on page 78 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Replace component under function test 170-000-XXX Voltage Sensor(s) Test Passed No action 170-0XX-XXX Voltage Sensor(s) failure 1. Flash system 170-195-XXX Voltage Sensor(s) Test aborted by user Information only Re-start the test, if necessary 170-196-XXX Voltage Sensor(s) test halt, error threshold exceeded 1. Press F3 to review the log file 2. System board 2. Re-start the test to reset the log file Chapter 7. Symptom-to-FRU Index 69 Diagnostic Error Code FRU/Action 170-197-XXX Voltage Sensor(s) test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 170-198-XXX Voltage Sensor(s) test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Go to “Undetermined problems” on page 78 170-199-XXX 1. See “Undetermined problems” on page Voltage Sensor(s) test failed, cause unknown 78 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Replace component under function test 170-250-XXX 170-251-XXX Voltage Sensor(s) Voltage limit error 1. AC/DC power adapter 170-254-XXX Voltage Sensor(s) Voltage Regulator Module error 1. Voltage Regulator Module (VRM) 175-000-XXX Thermal Sensor(s) Test Passed No action 175-0XX-XXX Thermal Sensor(s) failure 1. Flash system 175-195-XXX Thermal Sensor(s) Test aborted by user Information only Re-start the test, if necessary 175-196-XXX Thermal Sensor(s) test halt, error threshold exceeded 1. Press F3 to review the log file 175-197-XXX Thermal Sensor(s) test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 49 2. System board 2. Microprocessor 3. System board 2. System board 2. Re-start the test to reset the log file 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 70 Hardware Maintenance Manual Diagnostic Error Code FRU/Action 175-198-XXX Thermal Sensor(s) test aborted 1. If a component is called out, make sure it is connected and/or enabled 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Go to “Undetermined problems” on page 78 175-199-XXX Thermal Sensor(s) test failed, cause unknown 1. See “Undetermined problems” on page 78 2. Flash the system and re-test. See “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132 3. Replace component under function test 175-250-XXX 175-251-XXX Thermal Sensor(s) limit error 1. Check fans 2. Check AC/DC power adapter voltages 3. Microprocessor 4. System board 185-000-XXX Asset Security Test Passed No action 185-XXX-XXX Asset Security failure 1. Flash system 185-278-XXX Asset Security Chassis Intrusion 1. Assure Asset Security Enabled 2. System board 2. C2 Cover Switch 3. System board 201-000-XXX System Memory Test Passed No action 201-XXX-XXX System Memory error 1. Replace the memory module called out by the test 2. System board 202-000-XXX System Cache Test Passed No action 202-XXX-XXX System Cache error 1. Cache, if removable 2. System board 3. Microprocessor 206-000-XXX Diskette Drive Test Passed No action 206-XXX-XXX Diskette Drive error 1. Diskette Drive Cable 2. Check AC/DC power adapter voltages 3. Diskette drive 4. System board 215-000-XXX CD-ROM Drive Test Passed No action Chapter 7. Symptom-to-FRU Index 71 Diagnostic Error Code FRU/Action 215-XXX-XXX CD-ROM Drive error 1. CD-ROM Drive Cable 2. Check AC/DC power adapter voltages 3. CD-ROM drive 4. System board 217-000-XXX Hard Disk Drive Test Passed No action 217-25X-XXX 217-26X-XXX Hard Disk Drive (IDE) error 1. Hard Disk Drive Cable 2. Check AC/DC power adapter voltages 3. Reseat the hard disk drive cable 4. Hard Disk drive (IDE) 5. System board 217-28X-XXX 217-29X-XXX Hard Disk Drive (SCSI) error 1. Hard Disk Drive Cable 2. Check AC/DC power adapter voltages 3. Reseat the hard disk drive cable 4. Hard Disk drive (SCSI) 5. SCSI adapter card 6. System board 220-000-XXX Hi-Capacity Cartridge Drive Test Passed No action 220-XXX-XXX Hi-Capacity Cartridge Drive error 1. Remove the Hi-Capacity Cartridge Drive and re-test the system 301-XXX-XXX Keyboard error 1. Keyboard 2. Check and test mouse 3. System board 301-000-XXX Keyboard Test Passed No action 302-000-XXX Mouse Test Passed No action 302-XXX-XXX Mouse error 1. Mouse 2. Check and test Keyboard 3. System board 303-000-XXX Joystick Test Passed No action 303-XXX-XXX Joystick error Remove the Joystick and re-test the system 305-000-XXX Monitor DDC Test Passed No action 305-250-XXX Monitor DDC self test failure 1. Run Setup to enable DDC 2. Cable 3. Monitor 4. Video card 5. System board 415-000-XXX Modem Test Passed 72 Hardware Maintenance Manual No action Diagnostic Error Code FRU/Action 415-XXX-XXX Modem error Remove the Modem and re-test the system Chapter 7. Symptom-to-FRU Index 73 Beep symptoms Beep symptoms are tones or a series of tones separated by pauses (intervals without sound) during POST. The following tables describes beep symptoms. 74 Beep Symptom FRU/Action 1, 2, or 3 beeps Reseat the memory modules. If the error persists, replace the memory modules one at a time until the failing module is determined. 4, 5, 6, or 7 beeps 9, 10, or 11 beeps Before replacing the system board, remove any optional adapters (Express card, Modem card, Media reader) and retry. If the problem persists, replace the system board. Otherwise, reinstall the optional adapters one at a time until the failing adapter is determined. 8 beeps Replace the system board. Hardware Maintenance Manual POST error codes Each time you power-on the system, it performs a series of tests that check the operation of the system and some options. This series of tests is called the Power-On Self-Test, or POST. POST does the following operations. v Checks some basic system-board operations v Checks the memory operation v Starts the video operation v Verifies that the boot drive is working If the POST detects a problem, an error message appears on the screen. A single problem can cause several error messages to appear. When you correct the cause of the first error message, the other error messages probably will not appear on the screen the next time you turn on the system. POST Error Message Description/Action CMOS battery failed The CMOS battery is no longer functional. Replace the battery. CMOS checksum error - defaults loaded Checksum of CMOS is incorrect. The computer loads the default configuration settings. This error might indicate that CMOS has become corrupt due to a weak CMOS battery. CPU at nnnn nnnn is the running speed of the microprocessor. Press Esc to skip memory test Pressing Esc skips the full memory test HARD DISK INSTALL FAILURE Cannot find or initialize the hard disk drive controller or the drive. Make sure the hard disk drive is correctly installed. If no hard disk drives are installed, make sure the hard disk drive selection in Setup is set to NONE. Keyboard error or no keyboard present Cannot initialize the keyboard. Make sure the keyboard is properly connected to the computer and that no keys are held pressed during POST. To purposely configure the computer without a keyboard, set the error halt condition in Setup to HALT ON ALL, BUT KEYBOARD. The BIOS then ignores the missing keyboard during POST. Memory Test: This message displays during a full memory test, counting down the memory areas being tested. Memory test fail If POST detects an error during memory testing, additional information appears. This information gives specifics about the type and location of the memory error. Chapter 7. Symptom-to-FRU Index 75 POST Error Message Description/Action Press TAB to show POST screen Pressing the TAB key permits the user to toggle between the default POST display screen and a custom POST display screen. Error: Non-System disk or disk error Replace and press any key when ready The BIOS was unable to find a suitable boot device. Make sure the boot drive is properly connected to the computer. Make sure you have bootable media. 76 Hardware Maintenance Manual Miscellaneous error messages Message/Symptom FRU/Action Changing display colors Display/Monitor Computer will not power-off. See “Checking for power problems” on page 39. 1. Power Switch 2. System Board 3. Riser card, if installed Computer will not PXE from server 1. Ensure that network is in startup sequence as first device or first device after diskette 2. Ensure that network adapter is enabled for PXE 3. Network adapter (Advise network administrator of new MAC address) Computer will not perform a Wake On LAN® (if applicable) 1. Check power supply and signal cable connections to network adapter 2. Ensure that the operating system settings are set to enable Wake on LAN® 3. Ensure Wake On LAN feature is enabled in Setup/Configuration (see “Starting the Setup Utility program” on page 49) 4. Ensure network administrator is using correct MAC address 5. Ensure no interrupt or I/O address conflicts 6. Network adapter (advise network administrator of new MAC address) Dead computer. See “Checking for power problems” on page 39. 1. AC/DC Power Adapter Diskette drive in-use light remains on or does not light when drive is active. 1. Diskette Drive 2. System Board 2. System Board 3. Diskette Drive Cable Flashing cursor with an otherwise blank display. 1. System Board 2. Primary Hard Disk Drive 3. Hard Disk Drive Cable Incorrect memory size during POST 1. Run the Memory tests 2. Memory Module 3. System Board ″Insert a Diskette″ icon appears with a known-good diagnostics diskette in the first 3.5-inch diskette drive. Intensity or color varies from left to right of characters and color bars 1. System Board 2. Diskette Drive Cable 3. Network Adapter 1. Display 2. Video adapter (if present) 3. System Board No power or fan not running 1. See “Checking for power problems” on page 39. Chapter 7. Symptom-to-FRU Index 77 Message/Symptom FRU/Action Non-system disk or disk error-type message with a known-good diagnostic diskette. 1. Diskette Drive 2. System Board 3. Diskette Drive Cable Other display symptoms not listed above (including blank or illegible display) 1. Display 2. System Board Power-on indicator or hard disk drive in-use 1. Power switch/LED assembly light not on, but computer works correctly 2. System Board Printer problems 1. Printer 2. System Board Program loads from the hard disk with a known-good diagnostics diskette in the first 3.5-inch diskette drive 1. Run Setup and check Startup sequence. 2. Diskette Drive 3. Diskette Drive Cable 4. System Board 5. AC/DC power adapter PXE computer cannot access programs from its own hard disk. Replace the hard disk drive PXE computer does not PXE from server 1. Check startup sequence 2. Check the network adapter LED status Some or all keys on the keyboard do not work 1. Keyboard 2. Keyboard Cable 3. System Board Undetermined problems 1. Turn off the computer. 2. Remove or disconnect the following components (if installed) one at a time. a. External devices (modem, printer, or mouse) b. Any adapters c. Memory modules d. Extended video memory e. External Cache f. External Cache RAM g. Hard disk drive h. Diskette drive 3. Turn on the power to re-test the system. 4. Repeat steps 1 through 3 until you find the failing device or adapter. If all devices and adapters have been removed, and the problem continues, replace the system board. 78 Hardware Maintenance Manual Chapter 8. Replacing FRUs This chapter provides step-by-step instructions for replacing major FRUs. Important Before you replace any FRU, read Chapter 2, “Safety information,” on page 3. These precautions and guidelines will help you work safely. FRU replacements are to be done by trained service technicians only. © Copyright Lenovo 2006, 2007 79 Locations This section provides illustrations to help locate the various connectors, controls, and components of the computer. Connectors on the front of the computer Note: Not all computer models will have the following controls and connections. 1 2 3 80 USB connector Microphone connector Headphone connector Hardware Maintenance Manual 4 5 USB connector Media card reader Connectors on the rear of the computer 1 2 3 4 5 Cable lock latch AC/DC Power Adapter connector Monitor connector USB connectors (4) Ethernet connector 6 7 Microphone connector Audio line out connector 8 9 10 Audio line in connector Express card assembly RJ11 modem connector Chapter 8. Replacing FRUs 81 Locating components This section shows the location of the various components in the computer. 1 Front Audio/USB assembly 2 Hard disk drive 3 System fan assembly 4 Optical drive 5 AC/DC Power Adapter 6Express Card assembly 7 System board 82 Hardware Maintenance Manual 8 Microprocessor 9 Heat sink 10 Side cover 11 Memory modules 12 Internal speaker 13 Media Card Reader System board locations 1 Microprocessor and heat sink 9 2 3 4 5 6 7 8 Memory connectors (2) Thermal sense cable connector Front USB connector Power switch/LED connector Battery SATA IDE connectors (2) Clear CMOS/Recovery jumper 10 11 12 13 14 15 16 Modem daughter card (MDC) connector Express card USB connector Express card PCIe connector Media card reader connector Internal speaker connector Front audio connector Internal power distribution connector System fan connector Chapter 8. Replacing FRUs 83 Opening the cover Important Turn off the computer and wait 3 to 5 minutes to let the computer cool before opening the computer cover. This section provides instructions on how to open the computer cover. 1. Remove any media (diskettes, CDs, or tapes) from the drives, shut down your operating system, and turn off all attached devices and the computer. 2. Unplug all power cords from electrical outlets. 3. Disconnect the cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. See “Connectors on the front of the computer” on page 80 and “Connectors on the rear of the computer” on page 81. 4. Remove any locking devices, such as a cable lock that secures the computer cover. 5. Press the cover-release button on the side of the cover and pivot the computer cover outward. 6. If the computer cover is to be removed, disconnect all the cables from the system board. 84 Hardware Maintenance Manual Replacing the CMOS battery This procedure describes how to remove and replace the CMOS battery. If the CMOS battery fails, the date, time, and configuration information (including passwords) are lost. An error message is displayed when you turn on the computer. Important Refer to“Safety notices (multi-lingual translations)” on page 7 for information about replacing and disposing of the battery. CAUTION: When replacing the lithium battery, use only Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. 1. Open the computer cover. See “Opening the cover” on page 84. 2. Locate the battery. See “System board locations” on page 83. 3. Remove the old battery. 4. Install the new battery. 5. Close the computer cover, and connect all the cables. See “Completing the FRU replacement” on page 103. Note: When the computer is turned on for the first time after battery replacement, an error message might be displayed. This is normal after replacing the battery. 6. Use the Setup Utility program to set the date and time and any passwords. See Chapter 6, “Using the Setup Utility,” on page 49. Chapter 8. Replacing FRUs 85 Replacing the microprocessor This section provides instructions on how to replace the microprocessor. 1. Open the computer cover. See “Opening the cover” on page 84. 2. Locate the microprocessor. See “System board locations” on page 83. 3. Remove the four screws securing the heat sink to the retention module on the system board and lift the heat sink off the system board. 4. Disengage the microprocessor from the system board socket by pivoting the small handle upward until it is in the vertical position. 5. Lift the microprocessor straight up and out of the socket. Notes: a. Your microprocessor and socket might look different than the one illustrated. b. Note the orientation of the microprocessor in the socket. Look for the small triangle on one corner of the microprocessor. This is important when reinstalling the microprocessor on the system board. c. Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be kept as clean as possible. 86 Hardware Maintenance Manual 6. When installing the microprocessor make sure that the small handle is in the vertical position. 7. Holding the new microprocessor 1 with your fingers, remove the protective cover 2 that protects the microprocessor contacts. 8. Holding the microprocessor with your fingers, position the microprocessor so that the triangle 1 is properly aligned with the socket. 9. Lower the microprocessor straight down into the socket. Note: Install the black protective cover that was removed from the new microprocessor onto the defective microprocessor after the installation is complete. 10. Secure the microprocessor in the socket by pivoting the small handle downward. Be sure to lock it into position. Chapter 8. Replacing FRUs 87 11. Position the heat sink on the retention module so that the four screws are aligned with the posts on the system board. Tighten the four screws to secure the heat sink to the system board. 12. Go to “Completing the FRU replacement” on page 103. 88 Hardware Maintenance Manual Replacing the system board This section provides instructions on how to replace the system board. 1. Open the computer cover. See “Opening the cover” on page 84. 2. Take note of the location of all cable connections on the system board and disconnect all cables. See“System board locations” on page 83. 3. Remove the screws that secure the system board to the cover. 4. Lift the system board off of the cover. 5. Remove the memory modules from the failing system board and install them in the same location on the new system board. 6. If the system board has a modem daughter card installed, remove it from the failing system board and install it on the new system board. See “Replacing the modem” on page 95. 7. Remove the heat sink and microprocessor from the failing system board and install them on the new system board. See “Replacing the microprocessor” on page 86. 8. 9. 10. 11. Note: You might have to install a new retention module on the new system board. Position the new system board in the chassis so that the screw holes are aligned with the mounting studs. Install and tighten the screws that secure the system board to the chassis. Reconnect all cables to the system board. See“System board locations” on page 83. Go to “Completing the FRU replacement” on page 103 Chapter 8. Replacing FRUs 89 Replacing a hard disk drive This section provides instructions on how to replace the hard disk drive. Important When a new hard disk drive is installed, a set of Product Recovery discs might be required. The set of Product Recovery discs enable the contents of the hard disk to be restored to the same state as when the computer was originally shipped from the factory. For more information on recovering factory-installed software, refer to ″Recovering Software″ in the User Guide. To replace the hard disk drive: 1. Open the computer cover. See “Opening the cover” on page 84. 2. Disconnect the power cable from the optical drive. 3. Place your finger on the tab located on the front of the hard disk drive and push upward. Then press inward on the side tabs and pivot the hard disk drive upward to remove. 4. Remove the failing hard disk drive from the chassis. 5. Disconnect the signal and power cables from the hard disk drive. 6. Remove the hard disk drive from the plastic bracket by flexing the sides of the bracket enough to slide it free of the hard disk drive. 90 Hardware Maintenance Manual 7. To install the new hard disk drive into the plastic bracket 1, flex the bracket and align the pins on the bracket with the holes in the hard disk drive. Do not touch the circuit board 2 on the bottom of the hard disk drive. 8. 9. 10. 11. Connect the signal and power cables to the rear of the new hard disk drive. Slide the new hard disk drive into the drive bay until it snaps into position. Reconnect the power cable to the optical drive. Go to “Completing the FRU replacement” on page 103. Chapter 8. Replacing FRUs 91 Replacing an optical drive This section provides instructions on how to replace an optical drive. 1. Open the computer cover. See “Opening the cover” on page 84. 2. Remove the front bezel by releasing the two tabs and pivoting the bezel forward to remove completely. 3. Disconnect the signal and power cables from the rear of the optical drive. 4. Press the blue release button and remove the optical drive out the front of the computer. 5. Remove the retainer bracket from the failing drive and install it on the new optical drive. 92 Hardware Maintenance Manual 6. Slide the new optical drive into the drive bay until it snaps into position. 7. Connect the signal and power cables to the drive. 8. Replace the front bezel. 9. Go to “Completing the FRU replacement” on page 103. Chapter 8. Replacing FRUs 93 Replacing a memory module This section provides instructions on how to replace a memory module. 1. Open the computer cover. See “Opening the cover” on page 84. 2. Locate the memory connector. See “System board locations” on page 83. 3. Remove the memory module being replaced by opening the retaining clips as shown. 4. Insert the notched end 2 of the memory module into the socket 1. Press the memory module firmly, and pivot the memory module until it snaps into place. Make sure that the memory module is firmly fixed in the connector and does not move easily. 5. Go to “Completing the FRU replacement” on page 103. 94 Hardware Maintenance Manual Replacing the modem This section provides instructions on how to replace the modem. 1. Open the computer cover. See “Opening the cover” on page 84. 2. Locate the MDC connector. See “System board locations” on page 83. The modem card 1 will be connected to the MDC connector. 3. Remove the two screws that secure the modem card to the system board. 4. Disconnect the modem card from the system board. 5. Disconnect the RJ11 modem cable from the modem card. Chapter 8. Replacing FRUs 95 6. Connect the RJ11 modem cable to the new modem card. 7. Install the new modem card to the MDC connector on the system board by aligning the holes in the modem card with the pins in the system board. 8. Install the two screws to secure the modem card to the system board. 9. Go to “Completing the FRU replacement” on page 103. 96 Hardware Maintenance Manual Replacing the Express card assembly This section provides instructions on how to replace the Express card assembly. 1. Open the computer cover. See “Opening the cover” on page 84. 2. Locate the Express card assembly. See “Locating components” on page 82 3. Disconnect the cable connected to the Express card. 4. Remove the four screws that secure the Express card assembly to the Chassis. 5. Remove the Express card assembly from the system board. Chapter 8. Replacing FRUs 97 6. Install the new Express card assembly into the chassis by aligning the holes in the Express card assembly with the pins in the chassis. 7. Install the four screws to secure the Express card assembly to the chassis. 8. Reconnect the cable to the Express card assembly. 9. Go to “Completing the FRU replacement” on page 103. 98 Hardware Maintenance Manual Replacing the Media Card Reader This section provides instructions on how to replace the Media Card Reader. 1. Open the computer cover. See “Opening the cover” on page 84. 2. Locate the Media Card Reader. See “Locating components” on page 82 3. Disconnect the Media Card Reader cable connected to the system board. See “System board locations” on page 83 4. Remove the screw that secures the Media Card Reader to the Chassis. 5. Remove the Media Card Reader from the chassis. Chapter 8. Replacing FRUs 99 6. Install the new Media Card Reader into the chassis and align the screw-hole in the Media Card Reader with the hole in the chassis. 7. Install the screw to secure the Media Card Reader to the chassis. 8. Connect the Media Card Reader cable to the system board. 9. Go to “Completing the FRU replacement” on page 103. 100 Hardware Maintenance Manual Replacing the system fan assembly This section provides instructions on how to replace the system fan assembly. Note: When you receive your new system fan assembly, you will receive new rubber mounts. 1. Open the computer cover. See “Opening the cover” on page 84. 2. Locate the system fan connector. See “System board locations” on page 83. 3. Disconnect the system fan assembly cable from the system board. See “System board locations” on page 83. 4. You might have to remove the hard disk drive to gain access to the system fan. See “Replacing a hard disk drive” on page 90. 5. Remove the two rubber mounts from the system fan assembly that connect to the chassis by breaking them or cutting them with a pair of scissors. Once this has been done, remove the rubber mounts from the rear of the chassis. 6. Pull the system fan assembly outward from the chassis. Then lift the system fan assembly out of the chassis. 7. When installing your new system fan assembly, use the new rubber mounts that come with the new system fan. 8. Install the two short rubber mounts in the new system fan assembly as shown. 9. Install the two long rubber mounts into the rear of the chassis as shown. Push the mounts through the holes of the chassis. If necessary, pull the mounts through the holes from inside the chassis. Chapter 8. Replacing FRUs 101 10. To install the new system fan assembly into the chassis, align the open holes in the system fan assembly with the long rubber mounts in the chassis. Pull the rubber mounts through the holes in the system fan assembly until the system fan is in place. 11. Once the system fan assembly is secure, you should remove the extra rubber for the mounts. 12. Connect the system fan assembly cable to the system fan connector on the system board. 13. Replace the hard disk drive, if it was removed. 14. Go to “Completing the FRU replacement” on page 103. 102 Hardware Maintenance Manual Completing the FRU replacement After replacing the parts, you need to close the cover and reconnect cables, including telephone lines and power cords. Also, depending on the part that was replaced, you might need to confirm the updated information in the Setup Utility program. See Chapter 6, “Using the Setup Utility,” on page 49. This section provides instructions on how to complete the parts replacement. 1. Ensure that all components have been reassembled correctly and that no tools or loose screws are left inside the computer. See “Locating components” on page 82 for the location of various components. 2. Make sure that the cables are routed correctly before closing the computer cover. Important Correctly route all power supply cables to avoid interference when closing the computer cover. Keep cables clear of the hinges and sides of the computer chassis. 3. Position the computer cover on the chassis so that the rail guide on the bottom of the cover engages the rail. Then, push the computer cover closed until it snaps into position. Chapter 8. Replacing FRUs 103 4. If a cover lock is installed, lock the cover. 5. Reconnect the external cables and power cords to the computer. See “Connectors on the rear of the computer” on page 81. 6. To update your configuration, see Chapter 6, “Using the Setup Utility,” on page 49. 104 Hardware Maintenance Manual Chapter 9. FRU lists Attention: Read “Important information about replacing RoHS compliant FRUs” on page 2 before replacing any FRUs. Note: In the following tables, A CRU (Customer Replaceable Unit) is identified as either ″1″, ″2″, or N in the CRU column. An ″N″ means that the part is not a CRU. a ″1″ indicates that the CRU is external and a ″2″ indicates that the CRU is internal. Machine Type 6417 Item # 6417 FRUs FRU# CRU 1 Front audio/USB card and cable (included in Cables kit 41R8510) (all models) 41R8510 N 2 Hard disk drive, 80 GB 7200rpm SATA (models 11S 11L 11D 11Y 11A 11Q 11T 11E 11J 12U 12F 12S 12L 12D 12Y 12G) 40Y9034 2 2 Hard disk drive, 1TB 7200rpm SATA (models) 45C5973 2 3 System fan (all models) 41R8511 2 4 DVD-ROM Drive - 16x/48x - SATA (models 11S 11L 11D 11Y 11A 11Q 11T 11E 11J 12U 12F 12S 12L 12D 12Y 12G) 41N3325 2 © Copyright Lenovo 2006, 2007 105 Item # 6417 FRUs FRU# CRU 5 130W AC/DC Power Adapter (models 11S 11L 11D 11Y 11A 11Q 11T 11E 11J 12U 12F 12S 12L 12D 12Y 12G ) 42T5279 1 5 120W AC/DC Power Adapter (models) 41A9732 1 6 Express card assembly (all models) 41R8521 N 7 System board, Mini-ITX AMD Athlon/Sempron (ATI RS690C/SB600) (models 11S 11L 11D 11Y 11A 11Q 11T 11E 11J 12U 12F 12S 12L 12D 12Y 12G) 43C2767 N 7 System board, Mini-ITX AMD Athlon/Sempron (ATI RS690C/SB600) (models) 45C7723 N 8 Microprocessor, AMD Athlon 64 X2 BE 2400 AM2, 45W, 65nm; 2.3GHz, 1MB L2, 2GHz HTB, G2 (models) 43C6165 N 8 Microprocessor, AMD Sempron LE 1150 AM2, 45W, 65nm, 2.0GHz, 256K L2, G1 (models 11S 11L 11D 11Y 11A 11Q 11T 11E 11J 12U 12F 12S 12L 12D 12Y 12G) 43C6169 N 9 Heat sink Athlon/Sempron (all models) 41R8514 2 10 Chassis Kit (includes chassis assembly, Think-skin assembly cover, optical disk drive blank panel, Think bezel for Media Card Reader) (all models) 41R8509 N 11 Memory module, 512MB DDR2 PC2-5300 (667MHz) SoDIMM (models 11S 11L 11D 11Y 11A 11Q 11T 11E 11J 12U 12F 12S 12L 12D 12Y 12G) 43C3814 2 12 Internal speaker (all models) 41R8517 2 13 Media card reader (all models) 41R8519 N FRU# CRU Cable Kit (includes SATA data cable, internal device power cable, front audio/USB card/cable, and thermal sense cable) (all models) 41R8510 N Skins Kit (all models) 41R8508 N Hard Disk Drive tray (all models) 41R8518 2 Shield Kit (includes system board shield and optical disk drive shield) (all models) 41R8515 N Cable, Modem Card (all models) 41R8522 N Power switch/LED assembly (all models) 41R8526 N FRU# CRU US English (models 11L 11A 11Q 11E 12U 12G ) 41A5289 1 Arabic (models 12G) 41A5290 1 Belgian/French (models 12G) 41A5292 1 Belgian/UK (models 12G) 41A5293 1 Bulgarian (models 12G) 41A5295 1 Czech (models 12G) 41A5297 1 Danish (models 12G) 41A5298 1 Dutch (models 12G) 41A5299 1 French (models 12G) 41A5300 1 French Canadian 445 (models 12F) 41A5301 1 French Canadian 58 (models 12F) 41A5302 1 German (models 12G) 41A5303 1 The FRUs listed in the following tables are not illustrated. 6417 FRUs 6417 Keyboards (USB Preferred Pro) 106 Hardware Maintenance Manual 6417 Keyboards (USB Preferred Pro) FRU# CRU Hebrew (models 12G) 41A5306 1 Hungarian (models 12G) 41A5307 1 Iceland (models 12G) 41A5308 1 Italian 141 (models 12G) 41A5309 1 Japanese (models 11J) 41A5310 1 LA Spanish (models 11S 11D 11Y 12S 12D 12Y) 41A5312 1 Norwegian (models 12G) 41A5313 1 Polish (models 12G) 41A5314 1 Portuguese (models 12G) 41A5315 1 Romanian 096 (models 12G) 41A5317 1 Romanian 446 (models 12G) 41A5316 1 Russian/Cyrillic (models 12G) 41A5318 1 Serbian/Cyrillic (models 12G) 41A5319 1 Slovak (models 12G) 41A5320 1 Spanish (models 12G) 41A5321 1 Swedish/Finn (models 12G) 41A5322 1 Swiss (models 12G) 41A5323 1 Thailand (models 11T) 41A5324 1 Turkish 440 (models 12G) 41A5325 1 Turkish 179 (models 12G) 41A5326 1 UK English (models 12G) 41A5327 1 US Euro (models 12G) 41A5328 1 Slovenian (models 12G) 41A5329 1 FRU# CRU Optical Wheel Mouse (400DPI, USB) (models 11S 11L 11D 11Y 11A 11Q 11T 11E 11J 12U 12F 12S 12L 12D 12Y 12G) 41U3013 1 Optical Wheel Mouse (400DPI, USB) models 11S 11L 11D 11Y 11A 11Q 11T 11E 11J 12U 12F 12S 12L 12D 12Y 12G) 41U3030 1 6417 Adapters and miscellaneous FRUs FRU# CRU Speakers (2-piece) Lenovo Logo (models) 41A5331 1 BTL external speaker (models) 41A5334 1 Speaker Power brick - US, Canada, LA low voltage, ASEAN (models 12U 12S) 89P8571 1 Speaker Power brick - LA high voltage (non-APU) (models 12Y) 89P8575 1 Speaker Power brick - China, Thailand (models) 89P8581 1 Speaker Power brick - Japan (models) 89P8577 1 Speaker Power brick - Brazil (models) 89P8583 1 Speaker Power brick - Argentina (models) 41A4901 1 Speaker Power brick - ANZ (models) 89P8579 1 Speaker Brick - Korea (models) 41A4903 1 6417 mice Chapter 9. FRU lists 107 6417 Adapters and miscellaneous FRUs FRU# CRU Speaker Power brick - Hong Kong, Malaysia, Singapore, UK, Brunei (models 12G) 89P8573 1 Speaker Brick - Taiwan (models) 41A4905 1 Speaker Power brick - India, South Africa (models) 89P8585 1 Thermal Grease Syringe (models) 91P8835 N Modem Daughter Card (MDC 1.5) Kit (models) 39T0495 2 AC Line Cord for AC/DC Power Adapter - 1.8m/3 wire (models) 42T5089 1 FRU# CRU Power cord - US/Canada (models 11S 11D 11L 11A 11T 12S 12D 12L 12U ) 42T5004 1 Power cord (optional) - US/Canada (models 11S 11D 11L 11A 11T 12S 12D 12L 12U ) 42T5089 1 Power cord - Japan (models 11E 11J) 42T5011 1 Power cord (optional) - Japan (models 11E 11J) 42T5096 1 Power cord - Argentina (models 12Y 12L) 42T5017 1 Power cord (optional) - Argentina (models 12Y 12L) 42T5102 1 Power cord - Brazil (models) 42T5174 1 Power cord (optional) - Brazil (models 11P) 42T5177 1 Power cord - Europe (Germany) (models) 42T5029 1 Power cord (optional) - Europe (Germany) (models) 42T5114 1 Power cord - UK (models 11A) 42T5035 1 Power cord (optional) - UK (models 11A) 42T5120 1 Power cord - Denmark (models 12G) 42T5041 1 Power cord (optional) - Denmark (models 12G) 42T5126 1 Power cord - Switzerland (models) 42T5044 1 Power cord (optional) - Switzerland (models 12G) 42T5129 1 Power cord - Italy (models 11S 11Y 11L 12S 12Y 12L 12G ) 42T5047 1 Power cord (optional) - Italy (models 11S 11Y 11L 12S 12Y 12L 12G ) 42T5132 1 Power cord - Australia / New Zealand (models) 42T5050 1 Power cord (optional) - Australia / New Zealand (models) 42T5135 1 Power cord - South Africa (models 11A) 42T5056 1 Power cord (optional) - South Africa (models 11A) 42T5141 1 Power cord - Israel (models 12G) 42T5062 1 Power cord (optional) - Israel (models 12G) 42T5147 1 Power cord - China (PRC) (models) 42T5065 1 Power cord (optional) - China (PRC) (models) 42T5150 1 Power cord - Taiwan (models) 42T5071 1 Power cord (optional) - Taiwan (models) 42T5156 1 Power cord - Korea (models) 42T5077 1 Power cord (optional) - Korea (models) 42T5162 1 Power cord - India (models 11Q) 42T5083 1 Power cord (optional) - India (models 11Q) 42T5168 1 6417 Power Cords 108 Hardware Maintenance Manual 6417 Windows XP Pro Recovery CDs FRU# CRU US/UK/AP/TH (models 12U 12G 12L ) 45C4863 1 FR/CF (models 12F) 45C4864 1 GR (models 12G) 45C4865 1 IT (models 12G) 45C4867 1 BR (models 12G) TBD 1 SP/LA (models 12S 12P 12Y 12G ) 45C4866 1 DK (models 12G) 45C4871 1 NL (models 12G) 45C4872 1 TBD 1 SV (models 12G) 45C4870 1 HE (models 12G) 45C4875 1 FI (models 12G) 45C4874 1 NO (models 12G) 45C4869 1 PL (models 12G) 45C4876 1 PO (models 12G) 45C4880 1 RU (models 12G) 45C4877 1 RE (models 12G) TBD 1 HU (models 12G) TBD 1 CZ (models 12G) 45C4873 1 TR (models) 45C4878 1 GK (models 12G) 45C4879 1 SL (models 12G) TBD 1 45C4868 1 Simplified Chinese (models) TBD 1 Taiwan-TC (models) TBD 1 Hong Kong-TC (models) TBD 1 Korea (models) TBD 1 Multilingual 1 XP-P -- EN, NL, FR, GR, IT (models 12G) TBD 1 Multilingual 2 XP-P -- EN, DK, FI, NO, SV (models 12G) TBD 1 FRU# CRU AE (models) Japanese (models) 6417 Vista Home Basic 32 Recovery DVDs US/UK/AP/TH (models) 1 FR/CF (models) 1 GR (models) 1 SP/LA (models) 1 BR (models) 1 IT (models) 1 JP (models) 1 NO (models) 1 SV (models) 1 DK (models) 1 Chapter 9. FRU lists 109 6417 Vista Home Basic 32 Recovery DVDs FRU# CRU NL (models) 1 CZ (models) 1 FI (models) 1 PL (models) 1 RU (models) 1 TR (models) 1 HU (models) 1 GK (models) 1 PO (models) 1 CS (models) 1 TW (models) 1 HK (models) 1 KR (models) 1 SL (models) 1 RE (models) 1 6417 Vista Business 32 Recovery DVDs FRU# CRU US/UK/AP/TH (models) 1 FR/CF (models) 1 GR (models) 1 SP/LA (models) 1 BR (models) 1 IT (models) 1 JP (models) 1 NO (models) 1 SV (models) 1 DK (models) 1 NL (models) 1 CZ (models) 1 FI (models) 1 PL (models) 1 RU (models) 1 TR (models) 1 HU (models) 1 GK (models) 1 PO (models) 1 CS (models) 1 TW (models) 1 HK (models) 1 KR (models) 1 SL (models) 1 110 Hardware Maintenance Manual 6417 Vista Business 32 Recovery DVDs FRU# CRU RE (models) 1 Chapter 9. FRU lists 111 Machine Type 6418 Item # 6418 FRUs FRU# CRU 1 Front audio/USB card and cable (included in Cables kit 41R8510) (all models) (all models) 41R8510 N 2 Hard disk drive, 80 GB 7200rpm SATA (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q 11T 11K 11R 13U 13F ) 40Y9034 2 2 Hard disk drive, 160 GB 7200rpm SATA (models 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12Q 12T 12K 12R 12E 12J ) 40Y9035 2 2 Hard disk drive, 1TB 7200rpm SATA (models) 45C5973 2 3 System fan (all models) 41R8511 2 4 DVD-ROM/CD-RW Combo Drive - 48x/32x/48x/16x - SATA (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q 11T 11K 11R 13U 13F) 42Y9353 2 5 130W AC/DC Power Adapter (models 11U 11F 11S 11P 11L 11D 11Y 11G 11M 11A 11Q 11T 11K 11R 12U 12F 12S 12P 12L 12D 12Y 12G 12M 12A 12Q 12T 12K 12R 12E 12J 13U 13F) 42T5279 1 5 120W AC/DC Power Adapter (models) 41A9732 1 6 Express card assembly (all models) 41R8521 N 7 System board, Mini-ITX AMD Athlon/Sempron (ATI RS690C/SB600) (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q 11T 11K 11R 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12Q 12T 12K 12R 12E 12J 13U 13F) 43C2767 N 112 Hardware Maintenance Manual Item # 6418 FRUs FRU# CRU 7 System board, Mini-ITX AMD Athlon/Sempron (ATI RS690C/SB600) (models) 45C7723 N 8 Microprocessor, AMD Athlon 64 X2 BE 2400 (models) 43C6165 N 8 Microprocessor, AMD Athlon 64 X2 BE 2350 (models 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12Q 12T 12K 12R 12E 12J ) 43C6166 N 8 Microprocessor, AMD Sempron LE 1150 AM2, 45W, 65nm, 2.0GHz, 256K L2, G1 (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q 11T 11K 11R 13U 13F ) 43C6169 N 9 Heat sink Athlon/Sempron (all models) 41R8514 2 10 Chassis Kit (includes chassis assembly, Think-skin assembly cover, optical disk drive blank panel, Think bezel for Media Card Reader) (all models) 41R8509 N 11 Memory module, 1GB DDR2 PC2-5300 (667MHz) SoDIMM (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q 11T 11K 11R 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12Q 12T 12K 12R 12E 12J 13U 13F) 43C3815 2 12 Internal speaker (all models) 41R8517 2 13 Media card reader (all models) 41R8519 N FRU# CRU Cable Kit (includes SATA data cable, internal device power cable, front audio/USB card/cable, and thermal sense cable) (all models) 41R8510 N Skins Kit (all models) 41R8508 N Hard Disk Drive tray (all models) 41R8518 2 Shield Kit (includes system board shield and optical disk drive shield) (all models) 41R8515 N Cable, Modem Card (all models) 41R8522 N Power switch/LED assembly (all models) 41R8526 N FRU# CRU US English (models 11U 12U 11L 12L 11G 12G 11M 12M 11A 12A 11Q 12Q 11R 12R 11E 12E 13U 13F) 41A5289 1 Arabic (models 11G 12G) 41A5290 1 Belgian/French (models 11G 12G) 41A5292 1 Belgian/UK (models 11G 12G) 41A5293 1 Brazillian (models) 41A5294 1 Bulgarian (models 11G 12G) 41A5295 1 Chinese/US (models 11G 12G) 41A5296 1 Czech (models 11G 12G) 41A5297 1 Danish (models 11G 12G) 41A5298 1 Dutch (models 11G 12G) 41A5299 1 French (models 11G 12G) 41A5300 1 French Canadian 445 (models 11F 12F) 41A5301 1 French Canadian 58 (models 11F 12F) 41A5302 1 German (models 11G 12G) 41A5303 1 Greek (models 11G 12G) 41A5304 1 The FRUs listed in the following tables are not illustrated. 6418 FRUs 6418 Keyboards (USB Preferred Pro) Chapter 9. FRU lists 113 6418 Keyboards (USB Preferred Pro) FRU# CRU Greek/US (models 11G 12G) 41A5305 1 Hebrew (models 11G 12G) 41A5306 1 Hungarian (models 11G 12G) 41A5307 1 Iceland (models 11G 12G) 41A5308 1 Italian 141 (models 11G 12G) 41A5309 1 Japanese (models 11J 12J) 41A5310 1 Korean (models 11K 12K) 41A5311 1 LA Spanish (models 11S 12S 11D 12D 11Y 12Y) 41A5312 1 Norwegian (models 11G 12G) 41A5313 1 Polish (models 11G 12G) 41A5314 1 Portuguese (models 11G 12G) 41A5315 1 Romanian 096 (models 11G 12G) 41A5317 1 Romanian 446 (models 11G 12G) 41A5316 1 Russian/Cyrillic (models 11G 12G) 41A5318 1 Serbian/Cyrillic (models 11G 12G) 41A5319 1 Slovak (models 11G 12G) 41A5320 1 Spanish (models 11G 12G) 41A5321 1 Swedish/Finn (models 11G 12G) 41A5322 1 Swiss (models 11G 12G) 41A5323 1 Thailand (models 11T 12T) 41A5324 1 Turkish 440 (models 11G 12G) 41A5325 1 Turkish 179 (models 11G 12G) 41A5326 1 UK English (models 11G 12G) 41A5327 1 US Euro (models 11G 12G) 41A5328 1 Slovenian (models 11G 12G) 41A5329 1 FRU# CRU Optical Wheel Mouse (400DPI, USB) (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q 11T 11K 11R 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12Q 12T 12K 12R 12E 12J 13U 13F ) 41U3013 1 Optical Wheel Mouse (400DPI, USB) (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q 11T 11K 11R 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12Q 12T 12K 12R 12E 12J 13U 13F ) 41U3030 1 FRU# CRU Speakers (2-piece) Lenovo Logo (models) 41A5331 1 BTL external speaker (models) 41A5334 1 Speaker Power brick - US, Canada, LA low voltage, ASEAN (models 13U 11U 12U 11S 12S 11A 12A) 89P8571 1 Speaker Power brick - LA high voltage (non-APU) (models) 89P8575 1 Speaker Power brick - China, Thailand (models) 89P8581 1 Speaker Power brick - Japan (models) 89P8577 1 Speaker Power brick - Brazil (models) 89P8583 1 Speaker Power brick - Argentina (models) 41A4901 1 6418 mice 6418 Adapters and miscellaneous FRUs 114 Hardware Maintenance Manual 6418 Adapters and miscellaneous FRUs FRU# CRU Speaker Power brick - ANZ (models 11A 12A) 89P8579 1 Speaker Brick - Korea (models 11K 12K) 41A4903 1 Speaker Power brick - Hong Kong, Malaysia, Singapore, UK, Brunei (models 11G 12G) 89P8573 1 Speaker Brick - Taiwan (models) 41A4905 1 Speaker Power brick - India, South Africa (models) 89P8585 1 Thermal Grease Syringe (models) 91P8835 N Modem Daughter Card (MDC 1.5) Kit (models) 39T0495 2 AC Line Cord for AC/DC Power Adapter - 1.8m/3 wire (models) 42T5089 1 6418 Power Cords FRU# CRU Power cord - US/Canada (models 11U 12U 11F 12F 11S 12S 11D 12D 11L 12L 11A 12A 11T 12T 11L 12L 13U 13F) 42T5004 1 Power cord (optional) - US/Canada (models 11U 12U 11F 12F 11S 12S 11D 12D 11L 12L 11A 12A 11T 12T 11L 12L 13U 13F) 42T5089 1 Power cord - Japan (models 12E 12J) 42T5011 1 Power cord (optional) - Japan (models 12E 12J) 42T5096 1 Power cord - Argentina (models) 42T5017 1 Power cord (optional) - Argentina (models) 42T5102 1 Power cord - Brazil (models) 42T5174 1 Power cord (optional) - Brazil (models) 42T5177 1 Power cord - Europe (Germany) (models) 42T5029 1 Power cord (optional) - Europe (Germany) (models) 42T5114 1 Power cord - UK (models 11G 12G 11A 12A) 42T5035 1 Power cord (optional) - UK (models 11G 12G 11A 12A) 42T5120 1 Power cord - Denmark (models 11G 12G) 42T5041 1 Power cord (optional) - Denmark (models 11G 12G) 42T5126 1 Power cord - Switzerland (models 11G 12G) 42T5044 1 Power cord (optional) - Switzerland (models 11G 12G) 42T5129 1 Power cord - Italy (models 11S 12S 11Y 12Y 11L 12L 11G 12G) 42T5047 1 Power cord (optional) - Italy (models 11S 12S 11Y 12Y 11L 12L 11G 12G) 42T5132 1 Power cord - Australia / New Zealand (models 11M 12M) 42T5050 1 Power cord (optional) - Australia / New Zealand (models 11M 12M) 42T5135 1 Power cord - South Africa (models 11G 12G 11M 12M 11A 12A) 42T5056 1 Power cord (optional) - South Africa (models 11G 12G 11M 12M 11A 12A) 42T5141 1 Power cord - Israel (models 11G 12G) 42T5062 1 Power cord (optional) - Israel (models 11G 12G) 42T5147 1 Power cord - China (PRC) (models) 42T5065 1 Power cord (optional) - China (PRC) (models) 42T5150 1 Power cord - Taiwan (models) 42T5071 1 Power cord (optional) - Taiwan (models) 42T5156 1 Power cord - Korea (models 11K 12K 11R 12R) 42T5077 1 Chapter 9. FRU lists 115 6418 Power Cords FRU# CRU Power cord (optional) - Korea (models 11K 12K 11R 12R) 42T5162 1 Power cord - India (models 11Q 12Q) 42T5083 1 Power cord (optional) - India (models 11Q 12Q) 42T5168 1 FRU# CRU US/UK/AP/TH (models 13U) 45C4863 1 FR/CF (models 13F) 45C4864 1 6418 Windows XP Pro Recovery CDs GR (models) 1 IT (models) 1 BR (models) 1 SP/LA (models) 1 DK (models) 1 NL (models) 1 AE (models) 1 SV (models) 1 HE (models) 1 FI (models) 1 NO (models) 1 PL (models) 1 PO (models) 1 RU (models) 1 RE (models) 1 HU (models) 1 CZ (models) 1 TR (models) 1 GK (models) 1 SL (models) 1 Japanese (models) 1 Simplified Chinese (models) 1 Taiwan-TC (models) 1 Hong Kong-TC (models) 1 Korea (models) 1 Multilingual 1 XP-P -- EN, NL, FR, GR, IT (models) 1 Multilingual 2 XP-P -- EN, DK, FI, NO, SV (models) 1 6418 Vista Business 32 Recovery DVDs FRU# CRU US/UK/AP/TH (models 11U 11G 11M 11A 11Q 11R 12U 12G 12M 12A 12Q 12R 12E) 45C4836 1 Russian/English (models 11G 12G) 45C4837 1 French (models 11F 11G 12F 12G) 45C4838 1 German (models 11G 12G) 45C4839 1 Spanish (models 11G 12G) 45C4840 1 116 Hardware Maintenance Manual 6418 Vista Business 32 Recovery DVDs FRU# CRU Italian (models 11G 12G) 45C4841 1 Japan (models 12J) 45C4842 1 Norwegian (models 11G 12G) 45C4843 1 Swedish (models 11G 12G) 45C4844 1 Danish (models 11G 12G) 45C4845 1 Dutch (models 11G 12G) 45C4846 1 Czech (models 11G 12G) 45C4847 1 Finnish (models 11G 12G) 45C4848 1 Polish (models 11G 12G) 45C4849 1 Russian(models 11G 12G) 45C4850 1 Turkish (models 11G 12G) 45C4851 1 Hungarian (models 11G 12G) 45C4852 1 Greek (models 11G 12G) 45C4853 1 Simplified Chinese (models) 45C4854 1 Taiwan (models) 45C4855 1 Hong Kong (models) 45C4856 1 Korea (models 11K 12K) 45C4857 1 Slovenian (models 11G 12G) 45C4858 1 Romanian (models 11G 12G) 45C4859 1 Portuguese (models 11G 12G) 45C4860 1 Serbian (models) 45C4861 1 Slovakian (models 11G 12G) 45C4862 1 Chapter 9. FRU lists 117 Machine Type 6449 Item # 6449 FRUs FRU# CRU 1 Front audio/USB card and cable (included in Cables kit 41R8510) (all models) (all models) 41R8510 N 2 Hard disk drive, 80 GB 7200rpm SATA (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q 11T 11K 11R 13S 13L 13D 13Y 13G ) 40Y9034 2 2 Hard disk drive, 160 GB 7200rpm SATA (models 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12Q 12T 12K 12R 12E 12J ) 40Y9035 2 2 Hard disk drive, 1TB 7200rpm SATA (models) 45C5973 2 3 System fan (all models) 41R8511 2 4 DVD-ROM/CD-RW Combo Drive - 48x/32x/48x/16x - SATA (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q 11T 11K 11R 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12Q 12T 12K 12R 12E 12J 13L 13D 13S 13Y 13G ) 42Y9353 2 5 130W AC/DC Power Adapter (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q 11T 11K 11R 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12Q 12T 12K 12R 12E 12J 13L 13D 13S 13Y 13G ) 42T5279 1 5 120W AC/DC Power Adapter (models) 41A9732 1 6 Express card assembly (all models) 41R8521 N 7 System board, Mini-ITX AMD Athlon/Sempron (ATI RS690C/SB600) (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q 11T 11K 11R 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12Q 12T 12K 12R 12E 12J 13L 13D 13S 13Y 13G ) 43C2767 N 118 Hardware Maintenance Manual Item # 6449 FRUs FRU# CRU 7 System board, Mini-ITX AMD Athlon/Sempron (ATI RS690C/SB600) (models) 45C7723 N 8 Microprocessor, AMD Athlon 64 X2 BE 2400 AM2, 45W, 65nm; 2.3GHz, 1MB L2, 2GHz HTB, G2 (models) 43C6165 N 8 Microprocessor, AMD Athlon 64 X2 BE 2350 (models 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12Q 12T 12K 12R 12E 12J 13L 13D 13S 13Y 13G ) 43C6166 N 8 Microprocessor, AMD Sempron LE 1150 AM2, 45W, 65nm, 2.0GHz, 256K L2, G1 (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q 11T 11K 11R ) 43C6169 N 9 Heat sink Athlon/Sempron (all models) 41R8514 2 10 Chassis Kit (includes chassis assembly, Think-skin assembly cover, optical disk drive blank panel, Think bezel for Media Card Reader) (all models) 41R8509 N 11 Memory module, 512 MB DDR2 PC2-5300 (667MHz) SoDIMM (models 13S 13L 13D 13Y 13G) 43C3814 2 11 Memory module, 1GB DDR2 PC2-5300 (667MHz) SoDIMM (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q 11T 11K 11R 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12Q 12T 12K 12R 12E 12J ) 43C3815 2 12 Internal speaker (all models) 41R8517 2 13 Media card reader (all models) 41R8519 N FRU# CRU Cable Kit (includes SATA data cable, internal device power cable, front audio/USB card/cable, and thermal sense cable) (all models) 41R8510 N Skins Kit (all models) 41R8508 N Hard Disk Drive tray (all models) 41R8518 2 Shield Kit (includes system board shield and optical disk drive shield) (all models) 41R8515 N Cable, Modem Card (all models) 41R8522 N Power switch/LED assembly (all models) 41R8526 N FRU# CRU US English (models 11U 12U 11L 12L 11G 12G 11M 12M 11A 12A 11Q 12Q 11R 12R 11E 12E 13L 13G) 41A5289 1 Arabic (models 11G 12G 13G) 41A5290 1 Belgian/French (models 11G 12G 13G) 41A5292 1 Belgian/UK (models 11G 12G 13G) 41A5293 1 Brazillian (models) 41A5294 1 Bulgarian (models 11G 12G 13G) 41A5295 1 Chinese/US (models 11G 12G 13G) 41A5296 1 Czech (models 11G 12G 13G) 41A5297 1 Danish (models 11G 12G 13G) 41A5298 1 Dutch (models 11G 12G 13G) 41A5299 1 French (models 11G 12G 13G) 41A5300 1 French Canadian 445 (models 11F 12F) 41A5301 1 French Canadian 58 (models 11F 12F) 41A5302 1 The FRUs listed in the following tables are not illustrated. 6449 FRUs 6449 Keyboards (USB Preferred Pro) Chapter 9. FRU lists 119 6449 Keyboards (USB Preferred Pro) FRU# CRU German (models 11G 12G 13G) 41A5303 1 Greek (models 11G 12G 13G) 41A5304 1 Greek/US (models 11G 12G 13G) 41A5305 1 Hebrew (models 11G 12G 13G) 41A5306 1 Hungarian (models 11G 12G 13G) 41A5307 1 Iceland (models 11G 12G 13G) 41A5308 1 Italian 141 (models 11G 12G 13G) 41A5309 1 Japanese (models 11J 12J) 41A5310 1 Korean (models 11K 12K) 41A5311 1 LA Spanish (models 11S 12S 11D 12D 11Y 12Y 13S 13D 13Y) 41A5312 1 Norwegian (models 11G 12G 13G) 41A5313 1 Polish (models 11G 12G 13G) 41A5314 1 Portuguese (models 11G 12G 13G) 41A5315 1 Romanian 096 (models 11G 12G 13G) 41A5317 1 Romanian 446 (models 11G 12G 13G) 41A5316 1 Russian/Cyrillic (models 11G 12G 13G) 41A5318 1 Serbian/Cyrillic (models 11G 12G 13G) 41A5319 1 Slovak (models 11G 12G 13G) 41A5320 1 Spanish (models 11G 12G 13G) 41A5321 1 Swedish/Finn (models 11G 12G 13G) 41A5322 1 Swiss (models 11G 12G 13G) 41A5323 1 Thailand (models 11T 12T) 41A5324 1 Turkish 440 (models 11G 12G 13G) 41A5325 1 Turkish 179 (models 11G 12G 13G) 41A5326 1 UK English (models 11G 12G 13G) 41A5327 1 US Euro (models 11G 12G 13G) 41A5328 1 Slovenian (models 11G 12G 13G) 41A5329 1 FRU# CRU Optical Wheel Mouse (400DPI, USB) (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q 11T 11K 11R 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12Q 12T 12K 12R 12E 12J 13L 13D 13S 13Y 13G ) 41U3013 1 Optical Wheel Mouse (400DPI, USB) models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q 11T 11K 11R 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12Q 12T 12K 12R 12E 12J 13L 13D 13S 13Y 13G ) 41U3030 1 FRU# CRU Speakers (2-piece) Lenovo Logo (models) 41A5331 1 BTL external speaker (models) 41A5334 1 Speaker Power brick - US, Canada, LA low voltage, ASEAN (models 11U 12U 11S 12S 11A 12A 13S) 89P8571 1 Speaker Power brick - LA high voltage (non-APU) (models 13D 11D 12D ) 89P8575 1 6449 mice 6449 Adapters and miscellaneous FRUs 120 Hardware Maintenance Manual 6449 Adapters and miscellaneous FRUs FRU# CRU Speaker Power brick - China, Thailand (models) 89P8581 1 Speaker Power brick - Japan (models) 89P8577 1 Speaker Power brick - Brazil (models) 89P8583 1 Speaker Power brick - Argentina (models) 41A4901 1 Speaker Power brick - ANZ (models 11A 12A) 89P8579 1 Speaker Brick - Korea (models 11K 12K) 41A4903 1 Speaker Power brick - Hong Kong, Malaysia, Singapore, UK, Brunei (models 11G 12G 13G) 89P8573 1 Speaker Brick - Taiwan (models) 41A4905 1 Speaker Power brick - India, South Africa (models) 89P8585 1 Thermal Grease Syringe (models) 91P8835 N Modem Daughter Card (MDC 1.5) Kit (models) 39T0495 2 TBD 1 6449 Power Cords FRU# CRU Power cord - US/Canada (models 11U 12U 11F 12F 11S 12S 11D 12D 11L 12L 11A 12A 11T 12T 11L 12L 13U 13G 13L) 42T5004 1 Power cord (optional) - US/Canada (models 11U 12U 11F 12F 11S 12S 11D 12D 11L 12L 11A 12A 11T 12T 11L 12L 13U 13G 13L) 42T5089 1 Power cord - Japan (models 12E 12J) 42T5011 1 Power cord (optional) - Japan (models 12E 12J) 42T5096 1 Power cord - Argentina (models 13Y 13L) 42T5017 1 Power cord (optional) - Argentina (models 13Y 13L) 42T5102 1 Power cord - Brazil (models) 42T5174 1 Power cord (optional) - Brazil (models) 42T5177 1 Power cord - Europe (Germany) (models) 42T5029 1 Power cord (optional) - Europe (Germany) (models) 42T5114 1 Power cord - UK (models 11G 12G 11A 12A 13G) 42T5035 1 Power cord (optional) - UK (models 11G 12G 11A 12A 13G) 42T5120 1 Power cord - Denmark (models 11G 12G 13G) 42T5041 1 Power cord (optional) - Denmark (models 11G 12G 13G) 42T5126 1 Power cord - Switzerland (models 11G 12G 13G) 42T5044 1 Power cord (optional) - Switzerland (models 11G 12G 13G) 42T5129 1 Power cord - Italy (models 11S 12S 11Y 12Y 11L 12L 11G 12G 13S 13Y 13L 13G) 42T5047 1 Power cord (optional) - Italy (models 11S 12S 11Y 12Y 11L 12L 11G 12G 13S 13Y 13L 13G) 42T5132 1 Power cord - Australia / New Zealand (models 11M 12M) 42T5050 1 Power cord (optional) - Australia / New Zealand (models 11M 12M) 42T5135 1 Power cord - South Africa (models 11G 12G 11M 12M 11A 12A) 42T5056 1 Power cord (optional) - South Africa (models 11G 12G 11M 12M 11A 12A) 42T5141 1 Power cord - Israel (models 11G 12G 13G) 42T5062 1 Power cord (optional) - Israel (models 11G 12G 13G) 42T5147 1 Power cord - China (PRC) (models) 42T5065 1 AC Line Cord for AC/DC Power Adapter - 1.8m/3 wire (models) Chapter 9. FRU lists 121 6449 Power Cords FRU# CRU Power cord (optional) - China (PRC) (models) 42T5150 1 Power cord - Taiwan (models) 42T5071 1 Power cord (optional) - Taiwan (models) 42T5156 1 Power cord - Korea (models 11K 12K 11R 12R) 42T5077 1 Power cord (optional) - Korea (models 11K 12K 11R 12R) 42T5162 1 Power cord - India (models 11Q 12Q) 42T5083 1 Power cord (optional) - India (models 11Q 12Q) 42T5168 1 FRU# CRU US/UK/AP/TH (models 13U 13G) 45C4863 1 FR/CF (models 13F 13G) 45C4864 1 GR (models 13G) 45C4865 1 IT (models 13G) 45C4867 1 TBD 1 SP/LA (models 13S 13D 13Y) 45C4866 1 DK (models 13G) 45C4871 1 NL (models 13G) 45C4872 1 AE (models 13G) TBD 1 SV (models 13G) 45C4870 1 HE (models 13G) 45C4875 1 FI (models 13G) 45C4874 1 NO (models 13G) 45C4869 1 PL (models 13G) 45C4876 1 PO (models 13G) 45C4880 1 RU (models 13G) 45C4877 1 RE (models 13G) TBD 1 HU (models 13G) TBD 1 CZ (models 13G) 45C4873 1 TR (models 13G) 45C4878 1 GK (models 13G) 45C4879 1 SL (models 13G) TBD 1 45C4868 1 Simplified Chinese (models) TBD 1 Taiwan-TC (models) TBD 1 Hong Kong-TC (models) TBD 1 Korea (models) TBD 1 Multilingual 1 XP-P -- EN, NL, FR, GR, IT (models 13G) TBD 1 Multilingual 2 XP-P -- EN, DK, FI, NO, SV (models 13G) TBD 1 FRU# CRU 45C4836 1 6449 Windows XP Pro Recovery CDs BR (models) Japanese (models) 6449 Vista Business 32 Recovery DVDs US/UK/AP/TH (models 11U 11G 11M 11A 11Q 11R 12U 12G 12M 12A 12Q 12R 12E) 122 Hardware Maintenance Manual 6449 Vista Business 32 Recovery DVDs FRU# CRU Russian/English (models 11G 12G) 45C4837 1 French (models 11F 11G 12F 12G) 45C4838 1 German (models 11G 12G) 45C4839 1 Spanish (models 11G 12G) 45C4840 1 Italian (models 11G 12G) 45C4841 1 Japan (models 12J) 45C4842 1 Norwegian (models 11G 12G) 45C4843 1 Swedish (models 11G 12G) 45C4844 1 Danish (models 11G 12G) 45C4845 1 Dutch (models 11G 12G) 45C4846 1 Czech (models 11G 12G) 45C4847 1 Finnish (models 11G 12G) 45C4848 1 Polish (models 11G 12G) 45C4849 1 Russian(models 11G 12G) 45C4850 1 Turkish (models 11G 12G) 45C4851 1 Hungarian (models 11G 12G) 45C4852 1 Greek (models 11G 12G) 45C4853 1 Simplified Chinese (models) 45C4854 1 Taiwan (models) 45C4855 1 Hong Kong (models) 45C4856 1 Korea (models 11K 12K) 45C4857 1 Slovenian (models 11G 12G) 45C4858 1 Romanian (models 11G 12G) 45C4859 1 Portuguese (models 11G 12G) 45C4860 1 Serbian (models) 45C4861 1 Slovakian (models 11G 12G) 45C4862 1 Chapter 9. FRU lists 123 Machine Type 6453 Item # 6453 FRUs FRU# CRU 1 Front audio/USB card and cable (included in Cables kit 41R8510) (all models) 41R8510 N 2 Hard disk drive, 80 GB 7200rpm SATA (models 11S 11L 11D 11Y 11G 11A 11Q 11T 11E 11J ) 40Y9034 2 2 Hard disk drive, 1TB 7200rpm SATA (models) 45C5973 2 3 System fan (all models) 41R8511 2 4 DVD-ROM Drive - 16x/48x - SATA (models 11S 11L 11D 11Y 11G 11A 11Q 11T 11E 11J ) 41N3325 2 5 130W AC/DC Power Adapter (models 12S 12L 12D 12Y 12G) 42T5279 1 5 120W AC/DC Power Adapter (models) 41A9732 1 6 Express card assembly (all models) 41R8521 N 7 System board, Mini-ITX AMD Athlon/Sempron (ATI RS690C/SB600) (models 11S 11L 11D 11Y 11G 11A 11Q 11T 11E 11J ) 43C2767 N 7 System board, Mini-ITX AMD Athlon/Sempron (ATI RS690C/SB600) (models) 45C7723 N 8 Microprocessor, AMD Athlon 64 X2 BE 2400 AM2, 45W, 65nm; 2.3GHz, 1MB L2, 2GHz HTB, G2 (models) 43C6165 N 8 Microprocessor, AMD Sempron LE 1150 AM2, 45W, 65nm, 2.0GHz, 256K L2, G1 (models 11S 11L 11D 11Y 11G 11A 11Q 11T 11E 11J ) 43C6169 N 124 Hardware Maintenance Manual Item # 6453 FRUs FRU# CRU 9 Heat sink Athlon/Sempron (all models) 41R8514 2 10 Chassis Kit (includes chassis assembly, Think-skin assembly cover, optical disk drive blank panel, Think bezel for Media Card Reader) (all models) 41R8509 N 11 Memory module, 512MB DDR2 PC2-5300 (667MHz) SoDIMM (models 11S 11L 11D 11Y 11G 11A 11Q 11T 11E 11J ) 43C3814 2 12 Internal speaker (all models) 41R8517 2 13 Media card reader (all models) 41R8519 N FRU# CRU Cable Kit (includes SATA data cable, internal device power cable, front audio/USB card/cable, and thermal sense cable) (all models) 41R8510 N Skins Kit (all models) 41R8508 N Hard Disk Drive tray (all models) 41R8518 2 Shield Kit (includes system board shield and optical disk drive shield) (all models) 41R8515 N Cable, Modem Card (all models) 41R8522 N Power switch/LED assembly (all models) 41R8526 N FRU# CRU US English (models 11L 11G 11A 11Q 11E ) 41A5289 1 Arabic (models 11G ) 41A5290 1 Belgian/French (models 11G ) 41A5292 1 Belgian/UK (models 11G ) 41A5293 1 Brazillian (models 11G ) 41A5294 1 Bulgarian (models 11G ) 41A5295 1 Czech (models 11G ) 41A5297 1 Danish (models 11G ) 41A5298 1 Dutch (models 11G ) 41A5299 1 French (models 11G ) 41A5300 1 German (models 11G ) 41A5303 1 Greek (models 11G ) 41A5304 1 Greek/US (models 11G ) 41A5305 1 Hebrew (models 11G ) 41A5306 1 Hungarian (models 11G ) 41A5307 1 Iceland (models 11G ) 41A5308 1 Italian 141 (models 11G ) 41A5309 1 Japanese (models 11J) 41A5310 1 LA Spanish (models 11S 11D 11Y) 41A5312 1 Norwegian (models 11G ) 41A5313 1 Polish (models 11G ) 41A5314 1 Portuguese (models 11G ) 41A5315 1 The FRUs listed in the following tables are not illustrated. 6453 FRUs 6453 Keyboards (USB Preferred Pro) Chapter 9. FRU lists 125 6453 Keyboards (USB Preferred Pro) FRU# CRU Romanian 096 (models 11G ) 41A5317 1 Romanian 446 (models 11G ) 41A5316 1 Russian/Cyrillic (models 11G ) 41A5318 1 Serbian/Cyrillic (models 11G ) 41A5319 1 Slovak (models 11G ) 41A5320 1 Spanish (models 11G ) 41A5321 1 Swedish/Finn (models 11G ) 41A5322 1 Swiss (models 11G ) 41A5323 1 Thailand (models 11G ) 41A5324 1 Turkish 440 (models 11G ) 41A5325 1 Turkish 179 (models 11G ) 41A5326 1 UK English (models 11G ) 41A5327 1 US Euro (models 11G ) 41A5328 1 Slovenian (models 11G) 41A5329 1 FRU# CRU Optical Wheel Mouse (400DPI, USB) (models 11S 11L 11D 11Y 11G 11A 11Q 11T 11E 11J) 41U3013 1 Optical Wheel Mouse (400DPI, USB) models 11S 11L 11D 11Y 11G 11A 11Q 11T 11E 11J) 41U3030 1 FRU# CRU Speakers (2-piece) Lenovo Logo (models) 41A5331 1 BTL external speaker (models) 41A5334 1 Speaker Power brick - US, Canada, LA low voltage, ASEAN (models 12S) 89P8571 1 Speaker Power brick - LA high voltage (non-APU) (models 12D) 89P8575 1 Speaker Power brick - China, Thailand (models) 89P8581 1 Speaker Power brick - Japan (models) 89P8577 1 Speaker Power brick - Brazil (models) 89P8583 1 Speaker Power brick - Argentina (models) 41A4901 1 Speaker Power brick - ANZ (models) 89P8579 1 Speaker Brick - Korea (models) 41A4903 1 Speaker Power brick - Hong Kong, Malaysia, Singapore, UK, Brunei (models 12G) 89P8573 1 Speaker Brick - Taiwan (models) 41A4905 1 Speaker Power brick - India, South Africa (models) 89P8585 1 Thermal Grease Syringe (models) 91P8835 N Modem Daughter Card (MDC 1.5) Kit (models) 39T0495 2 TBD 1 FRU# CRU Power cord - US/Canada (models 11S 11D 11L 11A 11T) 42T5004 1 Power cord (optional) - US/Canada (models 11S 11D 11L 11A 11T) 42T5089 1 Power cord - Japan (models 11E 11J) 42T5011 1 6453 mice 6453 Adapters and miscellaneous FRUs AC Line Cord for AC/DC Power Adapter - 1.8m/3 wire (models) 6453 Power Cords 126 Hardware Maintenance Manual 6453 Power Cords FRU# CRU Power cord (optional) - Japan (models 11E 11J) 42T5096 1 Power cord - Argentina (models) 42T5017 1 Power cord (optional) - Argentina (models) 42T5102 1 Power cord - Brazil (models 11P) 42T5174 1 Power cord (optional) - Brazil (models 11P) 42T5177 1 Power cord - Europe (Germany) (models) 42T5029 1 Power cord (optional) - Europe (Germany) (models) 42T5114 1 Power cord - UK (models 11G 11A) 42T5035 1 Power cord (optional) - UK (models 11G 11A) 42T5120 1 Power cord - Denmark (models 11G) 42T5041 1 Power cord (optional) - Denmark (models 11G) 42T5126 1 Power cord - Switzerland (models 11G) 42T5044 1 Power cord (optional) - Switzerland (models 11G) 42T5129 1 Power cord - Italy (models 11S 11Y 11L 11G) 42T5047 1 Power cord (optional) - Italy (models 11S 11Y 11L 11G) 42T5132 1 Power cord - Australia / New Zealand (models) 42T5050 1 Power cord (optional) - Australia / New Zealand (models) 42T5135 1 Power cord - South Africa (models 11G 11A) 42T5056 1 Power cord (optional) - South Africa (models 11G 11A) 42T5141 1 Power cord - Israel (models 11G) 42T5062 1 Power cord (optional) - Israel (models 11G) 42T5147 1 Power cord - China (PRC) (models) 42T5065 1 Power cord (optional) - China (PRC) (models) 42T5150 1 Power cord - Taiwan (models) 42T5071 1 Power cord (optional) - Taiwan (models) 42T5156 1 Power cord - Korea (models) 42T5077 1 Power cord (optional) - Korea (models) 42T5162 1 Power cord - India (models 11Q) 42T5083 1 Power cord (optional) - India (models 11Q) 42T5168 1 FRU# CRU US/UK/AP/TH (models) 45C4863 1 FR/CF (models) 45C4864 1 GR (models ) 45C4865 1 IT (models ) 45C4867 1 BR (models) TBD 1 SP/LA (models) 45C4866 1 DK (models ) 45C4871 1 NL (models ) 45C4872 1 AE (models ) TBD 1 SV (models ) 45C4870 1 6453 Windows XP Pro Recovery CDs Chapter 9. FRU lists 127 6453 Windows XP Pro Recovery CDs FRU# CRU HE (models ) 45C4875 1 FI (models ) 45C4874 1 NO (models ) 45C4869 1 PL (models ) 45C4876 1 PO (models ) 45C4880 1 RU (models ) 45C4877 1 RE (models ) TBD 1 HU (models ) TBD 1 CZ (models ) 45C4873 1 TR (models ) 45C4878 1 GK (models ) 45C4879 1 SL (models ) TBD 1 45C4868 1 Simplified Chinese (models) TBD 1 Taiwan-TC (models) TBD 1 Hong Kong-TC (models) TBD 1 Korea (models) TBD 1 Multilingual 1 XP-P -- EN, NL, FR, GR, IT (models ) TBD 1 Multilingual 2 XP-P -- EN, DK, FI, NO, SV (models ) TBD 1 FRU# CRU US/UK/AP/TH (models) 45C4836 1 Russian/English (models ) 45C4837 1 French (models) 45C4838 1 German (models ) 45C4839 1 Spanish (models ) 45C4840 1 Italian (models ) 45C4841 1 Japan (models) 45C4842 1 Norwegian (models ) 45C4843 1 Swedish (models ) 45C4844 1 Danish (models ) 45C4845 1 Dutch (models ) 45C4846 1 Czech (models ) 45C4847 1 Finnish (models ) 45C4848 1 Polish (models ) 45C4849 1 Russian(models ) 45C4850 1 Turkish (models ) 45C4851 1 Hungarian (models ) 45C4852 1 Greek (models ) 45C4853 1 Simplified Chinese (models) 45C4854 1 Taiwan (models) 45C4855 1 Japanese (models) 6453 Vista Business 32 Recovery DVDs 128 Hardware Maintenance Manual 6453 Vista Business 32 Recovery DVDs FRU# CRU Hong Kong (models) 45C4856 1 Korea (models 11K 12K) 45C4857 1 Slovenian (models ) 45C4858 1 Romanian (models ) 45C4859 1 Portuguese (models ) 45C4860 1 Serbian (models) 45C4861 1 Slovakian (models ) 45C4862 1 Chapter 9. FRU lists 129 130 Hardware Maintenance Manual Chapter 10. Additional Service Information This chapter provides additional information that the service representative might find helpful. Security features Security features in this section include the following: v Passwords v Vital Product Data v Management Information Format (MIF) Hardware controlled Passwords Hardware controlled passwords are set using the Setup Utility program. For more information about passwords, see “Using passwords” on page 49. Operating system password An operating system password is very similar to a power-on password and denies access to the computer by an unauthorized user when the password is activated. The computer is unusable until the password is entered and recognized by the computer. Vital product data Each computer has a unique Vital Product Data (VPD) code stored in the nonvolatile memory on the system board. After you replace the system board, the VPD must be updated. To update the VPD, see “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132. BIOS levels An incorrect level of BIOS can cause false errors and unnecessary FRU replacement. Use the following information to determine the current level of BIOS installed in the computer, the latest BIOS available for the computer, and where to obtain the latest level of BIOS. v To determine the current Level of BIOS: – Start the Setup Utility. – Select System Information on the Main setup screen. v Sources for obtaining the latest level BIOS available 1. Lenovo support web site: http://www.lenovo.com/support/ 2. Lenovo Customer Support Center 3. Levels 1 and 2 Support To update (flash) the BIOS, see “Updating (flashing) BIOS from a CD-ROM or diskette” on page 132. © Copyright Lenovo 2006, 2007 131 Updating (flashing) BIOS from a CD-ROM or diskette This section describes how to update (flash) the BIOS using a CD-ROM or diskette. system program updates are available at http://www.lenovo.com/support on the World Wide Web. 1. To update (flash) the BIOS: v If using a CD-ROM, make sure the computer is turned on. Insert the system program update (flash) CD-ROM into the optical drive. The update begins. v If using a diskette, make sure the computer is turned off. Insert the system program update (flash) diskette and turn on the computer. The update begins. 2. When you are prompted to select a language, press the number on your keyboard that corresponds to the language and then press Enter. 3. When prompted to change the serial number, press Y. 4. Type the seven-character serial number of your computer and then press Enter. 5. When prompted to change the machine type/model, press Y. 6. Type the seven-character machine type/model of your computer and then press Enter. 7. Follow the instructions on the screen to complete the update. Recovering from a POST/BIOS update failure If power to your computer is interrupted while POST/BIOS is being updated (flash update), your computer might not restart correctly. If this happens, perform the following procedure commonly called Boot-block Recovery. 1. Turn off the computer and any attached devices, such as printers, monitors, and external drives. 2. Unplug all power cords from electrical outlets, and open the computer cover. See “Opening the cover” on page 84. 3. Locate the Clear CMOS/Recovery jumper on the system board. See “System board locations” on page 83. 4. Remove any cables that impede access to the Clear CMOS/Recovery jumper. 5. Move the jumper from the standard position (pins 1 and 2) to pins 2 and 3. 6. Close the computer cover and reconnect any cables that were disconnected. 7. Reconnect the power cords for the computer and monitor to electrical outlets. 8. Insert the POST/BIOS update (flash) diskette or CD-ROM into the drive, and turn on the computer and the monitor. 9. The recovery session will take two to three minutes. After the update session is completed, there will be no video, and the system will automatically reboot. Remove the diskette from the diskette drive. 10. Repeat steps 2 through 4. 11. Replace the Clear CMOS/Recovery jumper to its original position. 12. Close the computer cover and reconnect any cables that were disconnected. 13. Turn on the computer to restart the operating system. 132 Hardware Maintenance Manual Power management Power management reduces the power consumption of certain components of the computer such as the system power supply, processor, hard disk drives, and some monitors. Automatic configuration and power interface (ACPI) BIOS Being an ACPI BIOS system, the operating system is allowed to control the power management features of the computer and the setting for Advanced Power Management (APM) BIOS mode is ignored. Not all operating systems support ACPI BIOS mode. Automatic Power-On features The Automatic Power-On features within the Power Management menu allow you to enable and disable features that turn on the computer automatically. v RTC resume: You can specify a date and time at which the computer will be turned on automatically. This can be either a single event or a daily event. v Wake on LAN: If the computer has a properly configured token-ring or Ethernet LAN adapter card that is Wake on LAN-enabled and there is remote network management software, you can use the Wake on LAN feature. When you set Wake on LAN to Enabled, the computer will turn on when it receives a specific signal from another computer on the local area network (LAN). Chapter 10. Additional Service Information 133 134 Hardware Maintenance Manual Appendix. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead. However, it is the user’s responsibility to evaluate and verify the operation of any other product, program, or service. Lenovo may have patents or pending patent applications covering subject matter described in this document. The furnishing of this document does not give you any license to these patents. You can send license inquiries, in writing, to: Lenovo (United States), Inc. 1009 Think Place - Building One Morrisville, NC 27560 U.S.A. Attention: Lenovo Director of Licensing LENOVO PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you. This information could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time without notice. The products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. The information contained in this document does not affect or change Lenovo product specifications or warranties. Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties. All information contained in this document was obtained in specific environments and is presented as an illustration. The result obtained in other operating environments may vary. Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of the materials for this Lenovo product, and use of those Web sites is at your own risk. Any performance data contained herein was determined in a controlled environment. Therefore, the result obtained in other operating environments may © Copyright Lenovo 2006, 2007 135 vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment. Television output notice The following notice applies to models that have the factory-installed television-output feature. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo ThinkCentre PS/2 Rescue and Recovery The following terms are trademarks of International Business Machines Corporation in the United States, other countries, or both: Asset ID Alert on LAN IBM (used under license) Wake on LAN Intel and Pentium are trademarks of Intel Corporation in the United States, other countries, or both. Microsoft and Windows are trademarks of Microsoft Corporation in the United States, other countries, or both. Other company, product, or service names may be trademarks or service marks of others. 136 Hardware Maintenance Manual Part Number: 43C6257 Printed in USA (1P) P/N: 43C6257
advertisement
Key Features
- FRU part number listing
- Safety information
- Diagnostics
- Setup Utility
- Symptom-to-FRU index
- Replacing FRUs
- FRU lists
- Additional service information
Frequently Answers and Questions
What is the purpose of the ThinkCentre Hardware Maintenance Manual?
The manual provides service and reference information for ThinkCentre computers, intended for trained servicers familiar with Lenovo products.
What is the ThinkVantage Productivity Center?
It is a program that provides general information about the use, operation, and maintenance of your ThinkCentre computer.
Where can I find additional information resources for my ThinkCentre computer?
You can access additional information resources online at www.lenovo.com/support.