lin-035 rev07

lin-035 rev07
MANUAL: Hand Held Automatic
Dual Pressure Nozzles
and
INSTRUCTIONS FOR SAFE OPERATION AND MAINTENANCE
WARNING
Read instruction manual before use. Operation of this nozzle without understanding the
manual and receiving proper training can be dangerous and is a misuse of this
equipment. Call 800-348-2686 with any questions.
WARNING
This instruction manual is intended to familiarize firefighters and maintenance personnel
with the operation, servicing and safety procedures associated with the Mid-Force and
Dual-Force fire fighting nozzles.
WARNING
This manual should be kept available to all operating and maintenance personnel.
MID-FORCE
DUAL-FORCE
TASK FORCE TIPS, Inc.
www.tft.com
©Copyright Task Force Tips, Inc. 2002
®
2800 East Evans Avenue, Valparaiso, IN 46383-6940
800-348-2686 • 219-462-6161 • Fax 219-464-7155
LIN-035 November 25,2003 Rev 7
1.0 GENERAL INFORMATION
The Task Force Tips MID-FORCE and DUAL-FORCE nozzles are designed to provide excellent performance under most
fire fighting conditions. Their rugged construction is compatible with the use of fresh water (see section 5.0 for saltwater
use) as well as fire fighting foam solutions. Other important operating features are:
- Switchable from standard 100 PSI operation to low pressure
- Automatic pressure regulation at 100 PSI (meets NFPA 1964 automatic nozzle pressure requirements)
- Slide valve with valve handle detent flow control for excellent stream quality at all valve positions
- Quick-acting pattern control from straight stream to wide fog
- "Power fog teeth" for full-fill fog
- "Gasket grabber" inlet screen to keep large debris from entering nozzle
- Easily flushable while flowing to clear trapped debris
- TFT's five-year warranty and unsurpassed customer service
1.1 VARIOUS MODELS AND TERMS
The TFT MID-FORCE and DUAL-FORCE nozzles are available in several different models. Some common models
and operating features are shown in figure 1.
SERIES
FLOW RANGE (GPM)
GPM
l/min
NOMINAL PRESSURE (PSI)
PSI
BAR
STANDARD COUPLING*
MID-FORCE
70-200
100
7
1-1/2 NH
DUAL-FORCE
95-250
100
7
1-1/2 NH
* Other threads, coupling sizes, or connector styles can be specified at time of order.
OW
FL
ON
COUPLING
CONTR
OL
OFF
BARREL LABEL
STREAM
SHAPER
NAME LABEL
PRESSURE
CONTROL
KNOB
RUBBER
GASKET
PISTOL
GRIP
NOZZLE WITH VALVE
and INTEGRAL PISTOL GRIP
DETENTS
VALVE HANDLE
TIP ONLY NOZZLE
VALVE POSITION
LABEL
VALVE RING
GASKET
GRABBER
INLET
SCREEN
NOZZLE WITH VALVE
2
TIP ONLY NOZZLE
WITH TWIST SHUTOFF
FIGURE 1 - COMMON MODELS AND TERMS
1.2 COLOR CODED VALVE HANDLE COVERS
The TFT MID-FORCE and DUAL-FORCE with lever type valve handles are supplied with black valve handle covers. The
handle covers are available from TFT in various colors for those departments wishing to color code the nozzle to the
discharge controls. A colored handle cover set will be sent upon receipt of the warranty card by TFT. Your department's
name can also be engraved on the covers (see warranty card for more information).
Handle covers are replaceable by removing the four screws that hold the handle covers in place. Use a 3/32” allen
wrench when replacing screws.
For standardization NFPA 1901 (A-4-9.3) recommends the following color code scheme:
Preconnect #1 or Bumper Jump Line Orange
Preconnect or discharge #5
Blue
Preconnect or discharge #2
Red
Preconnect or discharge #6
Black
Preconnect or discharge #3
Yellow
Preconnect or discharge #7
Green
Preconnect or discharge #4
White
Foam Lines
Red w/ White border
(Red/White)
1.3 NOZZLE COUPLING
Rocker lug 1-1/2" NH full-time swivel is standard on models with lever type flow control. The coupling is the same on
other models except it does not swivel. Other threads such as 1-1/2" NPSH can be specified at time of order.
CAUTION
Nozzle must be mated to a hose line with matched threads. Mismatched or damaged
threads may cause nozzle to leak or uncouple from hose under pressure and could cause
injury.
2.0 FLOW CHARACTERISTICS
The graphs in figure 2 show the typical performance of MID-FORCE and DUAL-FORCE nozzles.
meets NFPA flow requirements.
FLOW (l/min)
0
150
300
450
600
750
The charts in section 8.0 of this document
give specific examples of maximum flow
rates for particular situations. Friction
losses may vary due to differences in hose
construction resulting in flows different
than those shown. For situations or lengths
of hose not listed on the chart, approximate
flows can be calculated using conventional
hydraulics. NOTE: Within the flow range,
the nozzle inlet pressure may be
approximated to be 100 PSI when used
in the standard pressure mode.
8.3
STANDARD PRESSURE
100
6.9
80
5.5
LOW PRESSURE
60
4.1
40
2.7
70 - 200 GPM Flow Range
20
1.4
0
NOZZLE PRESSURE (BAR)
NOZZLE PRESSURE (PSI)
120
0
0
20
40
60
80
100 120 140 160 180 200 220
FLOW (GPM)
For Nozzles Manufactured
After December 1, 2003
meets NFPA flow requirements.
FLOW (l/min)
150
300
450
600
750
900
1060
8.3
STANDARD PRESSURE
100
6.9
80
5.5
60
4.1
LOW PRESSURE
40
95 - 250 GPM
Flow Range
20
2.7
1.4
0
0
0
20
40
60
80
NOZZLE PRESSURE (BAR)
NOZZLE PRESSURE (PSI)
120
0
FIGURE 2
NOZZLE
PERFORMANCE
100 120 140 160 180 200 220 240 260 280 300 320
FLOW (GPM)
3
DANGER
An inadequate supply of nozzle pressure and/or flow will cause an ineffective stream and
can result in injury, death or loss of property. See flow chart in section 8.0 or call 800-3482686 for assistance.
WARNING
Failure to restrain nozzle reaction can cause firefighter injury from loss of footing and/or
stream protection. Nozzle reaction will vary as supply conditions change: such as
opening or closing other nozzles, hose line kinks, changes in pump settings, etc.
Changes in spray pattern, flushing, or pressure control knob will also affect nozzle
reaction. The nozzle operator must always be positioned to restrain the nozzle reaction
in the event of those changes.
WARNING
Injury from whipping can occur. If nozzle gets out of control or away from operator, retreat
from nozzle immediately. Do not attempt to regain control of nozzle while flowing water.
CAUTION
Fire streams are capable of injury and damage. Do not direct water stream to cause injury
or damage to persons or property.
3.0 NOZZLE CONTROLS
3. 1 FLOW CONTROL
3.1.1 LEVER TYPE FLOW CONTROL
On models that use a lever type valve handle, the nozzle is shut off when the handle is fully forward. The valve handle has
six detent flow positions. These detent positions allow the nozzle operator to regulate the flow of the nozzle depending on
the need or what can be safely and effectively handled. TFT recommends the use of a pistol grip for easier handling. For
additional stress reduction, a hose rope or strap may also be used. This permits more effective use and ease of
advancement, while minimizing strain and fatigue.
3.1.2 TWIST SHUTTOFF
On models that use a twist flow control. The valve is opened or closed by rotating the valve ring. Rotating the ring
clockwise (as seen from the operating position behind the nozzle) closes the valve, while counterclockwise rotation
opens it. Detents are provided at four intermediate positions and the position of the valve is shown by the exposed valve
position label.
3.1.3 TIP ONLY NOZZLES
Tip only nozzles have NO shut off valve contained within the nozzle and MUST be used with a separate ball valve
attached to the nozzle.
3.2 PATTERN AND FLUSH CONTROL
3.2.1 PATTERN CONTROL
The TFT's MID-FORCE and DUAL-FORCE have full pattern control from straight stream to wide fog. Turning the STREAM
SHAPER clockwise (as seen from the operating position behind the nozzle) moves the SHAPER to the straight stream
position. Turning the SHAPER counterclockwise will result in an increasingly wider pattern.
Since the stream trim point varies with the flow, the stream should be "trimmed" after changing the flow to obtain the
straightest and farthest reaching stream. To properly trim a stream, first open the pattern to a narrow fog. Then close the
stream to parallel to give maximum reach. NOTE: Turning the shaper further forward will cause stream crossover
and reduce the effective reach of the nozzle.
The nozzle reaction is greatest when the shaper is in the straight stream position. The nozzle operator must be prepared
for a change in reaction as the pattern is changed.
4
3.2.2 FLUSH CONTROL
Small debris passes through the gasket grabber and may get caught inside the nozzle. This trapped material will cause
poor stream quality, shortened reach and reduced flow. To remove this trapped debris the nozzle can be flushed as
follows; while still flowing water, turn the SHAPER counterclockwise past the full fog position (increased resistance will be
felt on the SHAPER as the nozzle goes into flush). This will open the nozzle allowing debris to pass through. Rotate the
SHAPER clockwise and out of flush to continue normal operation. During flush the nozzle reaction will decrease as the
pattern becomes wider and the pressure drops. The nozzle operator must be prepared for an increase of nozzle reaction
when returning the nozzle from the flush position to retain control of the nozzle.
WARNING
Large amounts of debris can reduce the flow of the
nozzle resulting in an ineffective flow. In the event
of a blockage it may be necessary to retreat to a
safe area, uncouple nozzle and remove debris.
FIGURE 3 - GASKET GRABBER
3.3 STANDARD/LOW PRESSURE KNOB
For situations where 100 PSI at the nozzle is impractical, the MID-FORCE or DUAL-FORCE may be switched to an low
pressure mode. In the low pressure mode the nozzle pressure is reduced by about 50% while maintaining a usable
stream and increasing the flow. The nozzle operator must be prepared for a change in reaction when changing modes.
See figure 2 or the flow chart in section 8.0 for actual performance.
To switch to the low pressure mode, shut off water flow with valve and turn knob at front of nozzle (see figure 4)
counterclockwise (when viewed from front). Reopen valve to flow water at reduced pressure. Repeat the process,
except turn knob clockwise, to return to 100 PSI operation.
To obtain dual pressure capability, a knob is added to the front end of the baffle. This knob protrudes past the end
of the nozzle when the shaper is rotated back. As a consequence, the knob and baffle may be damaged if
subjected to impact such as from a drop. The knob and baffle portion of the nozzle does NOT meet NFPA 1964's
rough usage requirement of a six foot drop onto concrete (paragraph 4-7.1). In the event of damage to this section
the stream quality may be affected as well as nozzle pressure regulation.
Knob In
Standard Operating Mode
Knob In
Low Pressure Mode
FIGURE 4
5
4.0 USE OF MID-FORCE and DUAL-FORCE NOZZLES
IT IS THE RESPONSIBILITY OF THE INDIVIDUAL FIRE DEPARTMENT OR AGENCY TO DETERMINE
PHYSICAL CAPABILITIES AND SUITABILITY FOR AN INDIVIDUAL'S USE OF THIS EQUIPMENT.
Many factors contribute to the extinguishment of a fire. Among the most important is delivering water at a flow rate
sufficient to absorb heat faster than it is being generated. The flow rate depends largely on the pump discharge pressure
and hose friction loss. The pump discharge pressure may be found by use of the chart in section 8.0. It can also be
calculated using a hydraulic equation such as:
Within its flow range, the nozzle pressure (NP) of the MID-FORCE
or DUAL-FORCE nozzle may be approximated as 100 PSI in the
standard mode. For additional information on calculating specific
hose layouts, consult an appropriate fire service training manual,
A Guide to Automatic Nozzles, or call TFT's "Hydraulics Hotline" at
800-348-2686.
PDP = NP+FL+DL+EL
PDP = Pump discharge pressure in PSI
NP = Nozzle pressure in PSI
FL = Hose friction loss in PSI
DL = Device loss in PSI
EL = Elevation loss in PSI
5.0 FIELD INSPECTION
TFT's MID-FORCE and DUAL-FORCE are designed and manufactured to be damage resistant and require minimal
maintenance. However, as the primary fire fighting tools upon which your life depends, they should be treated
accordingly. Use with saltwater is permissible provided nozzle is thoroughly cleaned with fresh water after each use. The
service life of the nozzle may be shortened due to the effects of corrosion and is not covered under warranty.
WARNING
Nozzle must be inspected for proper operation and function according to inspection
checklist on the last page before each use. Any nozzle that fails inspection is dangerous
to use and must be repaired before using.
Performance tests shall be conducted on the Mid-Force and Dual-Force nozzle after a repair, or anytime a problem is
reported to verify operation in accordance with TFT test procedures. Consult factory for the procedure that corresponds
to the model and serial number of the nozzle. Any equipment which fails the related test criteria should be removed from
service immediately. Troubleshooting guides are available with each test procedure or equipment can be returned to the
factory for service and testing. Factory service is available with repair time seldom exceeding one day in our facility.
Factory serviced nozzles are repaired by experienced technicians to original specifications, fully tested and promptly
returned. Any returns should include a note as to the nature of the problem, who to reach in case of questions and if a
repair estimate is required.
TFT Item#
LHM-020
LHD-020
CAUTION
Title
Mid-Matic & Mid-Force Service Procedure
Handline & Dual-Force Service Procedure
Any alterations to the nozzle and its markings could diminish safety and constitutes a
misuse of this product.
All Task Force Tip nozzles are factory lubricated with high quality silicone grease. This lubricant has excellent washout
resistance and long term performance. If your department has unusually hard or sandy water, the moving parts may be
affected. Foam agents and water additives contain soaps and chemicals that may break down the factory lubrication.
The moving parts of the nozzle should be checked on a regular basis for smooth and free operation, and signs of
damage. IF THE NOZZLE IS OPERATING CORRECTLY, THEN NO ADDITIONAL LUBRICATION IS NEEDED. Any
nozzle that is not operating correctly should be immediately removed from service and the problem corrected.
6
6.0 WARRANTY
Task Force Tips, Inc., 2800 East Evans Avenue, Valparaiso, Indiana 46383 ("TFT") warrants to the original purchaser of its
Dual-Force and Mid-Force nozzles and other equipment ("equipment"), and to anyone to whom it is transferred, that the
equipment shall be free from defects in material and workmanship during the five (5) year period from the date of
purchase.
TFT's obligation under this warranty is specifically limited to replacing or repairing the equipment (or its parts) which
are shown by TFT's examination to be in a defective condition attributable to TFT. To qualify for this limited warranty,
the claimant must return the equipment to TFT, at 2800 East Evans Avenue, Valparaiso, Indiana 46383, within a
reasonable time after discovery of the defect. TFT will examine the equipment. If TFT determines that there is a
defect attributable to it, TFT will correct the problem within a reasonable time. If the equipment is covered by this
limited warranty, TFT will assume the expenses of repair.
If any defect attributable to TFT under this limited warranty cannot be reasonably cured by repair or replacement, TFT
may elect to refund the purchase price of the equipment, less reasonable depreciation, in complete discharge of its
obligations under this limited warranty. If TFT makes this election, claimant shall return the equipment to TFT free and
clear of any liens and encumbrances.
This is a limited warranty. The original purchaser of the equipment, any person to whom it is transferred, and any person
who is an intended or unintended beneficiary of the equipment, shall not be entitled to recover from TFT any
consequential or incidental damages for injury to person and/or property resulting from any defective equipment
manufactured or assembled by TFT. It is agreed and understood that the price stated for the equipment is in part
consideration for limiting TFT's liability. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above may not apply to you.
TFT shall have no obligation under this limited warranty if the equipment is, or has been, misused or neglected (including
failure to provide reasonable maintenance) or if there have been accidents to the equipment or if it has been repaired or
altered by someone else.
THIS IS A LIMITED EXPRESS WARRANTY ONLY. TFT EXPRESSLY DISCLAIMS WITH RESPECT TO THE
EQUIPMENT ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND ALL IMPLIED WARRANTIES OF FITNESS
FOR A PARTICULAR PURPOSE. THERE IS NO WARRANTY OF ANY NATURE MADE BY TFT BEYOND THAT
STATED IN THIS DOCUMENT.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
7.0 ANSWERS TO YOUR QUESTIONS
We appreciate the opportunity of serving you and making your job easier. If you have any problems or questions, our tollfree "Hydraulics Hotline", 800-348-2686, is normally available to you 24 hours a day, 7 days a week.
8.0 NOZZLE FLOW CHARTS
7
84
40
93
31
121
42
143
52
31
13
65
30
125 93
45
225
200
175
150
100
75
17
8
41
84
15
36
8
22
STD
50
69
78
76
70
66
73
63
94
72
---
---
82
---
---
183 209 158 186 142 168
87
102
65
105
66
58
78
86
81
75
102
96
91
83
198 221 176 203
91
---
---
79
57
70
---
---
---
---
109
212
87
---
---
---
---
---
---
95
84
---
---
113
222
97
---
---
---
---
98
187 223
78
(1) Number on top in each box indicates flow (GPM), and number on bottom indicates nozzle reaction (LBS). (2) In Standard mode, the average nozzle pressure is 100 PSI. (3) Flows may vary with brand or condition of hose. (4)
Flows are approximate and do not reflect losses in preconnect piping.
---
---
---
90
---
90
73
52
84
57
---
59
56
153
41
119
22
68
LP
168 220 151 205
---
---
63
141 173 128 156 204 228 175 207 157 189
69
162 196
72
57
---
66
36
75
15
34
8
22
STD
-----
63
63
167
45
128
24
75
LP
62
---
77
38
79
15
35
8
22
STD
250 ft.
90
---
72
72
184
51
141
27
82
LP
200 ft.
138 135 213 122 198 113 182
40
117
30
91
17
54
LP
140 180 124 159 112 143 174 213 151 192 136 175
46
44
91
29
63
13
31
7
21
STD
150 ft.
101
52
56
152
45
129
33
100
19
60
LP
250 ft.
141 195 125 174 114 158 196
48
97
32
67
14
32
8
21
STD
200 ft.
2" HOSE
= STANDARD PRESSURE MODE
= LOW PRESSURE MODE
58
52
47
61
59
130
96
65
117 163 105 143
54
39
52
143
114 108 172
34
72
38
111
21
65
LP
37
32
97
25
55
14
32
75
24
8
21
STD
14
46
12
28
7
21
LP
150 ft.
77
126
36
107
27
83
16
50
STD
250 ft.
1 3/4" HOSE
44
27
59
12
29
7
21
55
21
50
STD
LP
STD
LP
200 ft.
150 ft.
1 1/2" HOSE
LP
STD
CAUTION: Changing to Low Pressure mode will typically increase nozzle reaction.
PUMP DISCHARGE PRESSURE (PSI)
FLOW (GPM)
REACTION
(LBS)
Flow And
Nozzle Reaction Chart
8
9
80
210
8
80
4
7
190
LP
3
80
7 bar
6
175
LP
14
245
6
5
12
5
11
6
85
4
80
7 bar
4
80
7 bar
9
225
LP
3
80
7 bar
8
205
LP
4
85
7 bar
12
310
LP
45M
4
85
7 bar
11
285
LP
60M
4
85
7 bar
10
225
LP
75M
17
6
15
6
14
175
23
7
20
7
19
420 120 380 115 345 135 535 130 485 130 450
10
245
LP
75M
50mm HOSE
= STANDARD PRESSURE MODE
= LOW PRESSURE MODE
19
12
16
11
15
15
24
15
20
13
18
19
33
17
29
16
25
460 225 405 210 365 275 540 255 490 240 445 320 695 300 630 285 580
14
115 350 110 315 105 285
3
7 bar
LP
7 bar
60M
45M
75M
45M
60M
45mm HOSE
38mm HOSE
LP
7 bar
33
29
---
33
---
37
43
40
---
---
695 790 600 705 535 635
35
32
30
39
37
34
46
44
41
38
750 835 665 770
41
660 785 595 715
35
---
---
---
---
---
---
50
800
40
635
---
---
---
---
---
---
--
---
38
---
---
51
840
44
---
---
---
---
45
710 845
35
570 775
(1) Number on top in each box indicates flow (LPM), and number on bottom indicates nozzle reaction (KG). (2) In Standard mode, the average nozzle pressure is 7 bar. (3) Flows may vary with brand or condition of hose. (4) Flows are
approximate and do not reflect losses in preconnect piping.
---
---
-----
30
48
30
26
35
---
41
---
41
33
24
38
26
26
---
27
30
---
29
535 655 485 590 770
31
615 740
33
29
---
35
---
33
---
21
---
21
530 680 470 600 425 540 660 805 570 725 515 660
24
CAUTION: Changing to Low Pressure mode will typically increase nozzle reaction.
1550
1400
1200
24
---
--46
28
535 740 475 660 430 600 740
26
27
445 615 395 540 365 490
540 320 475 290 430 410 650 365 575 345 520 510 805 460 750 430 690
860 350
20
17
18
25
30
22
25
31
36
26
18
20
20
23
41
28
32
24
700
520
350
1000
FLOW (LPM)
REACTION
(KG)
Flow And
Nozzle Reaction Chart
PUMP DISCHARGE PRESSURE (KPA)
89
42
91
31
118
41
59
23
74
33
100 141
47
38
83
25
61
17
50
52
144
38
110
20
62
35
77
24
60
16
49
STD
45
128
33
98
18
56
LP
39
58
65
51
56
112 119 172 107 152
32
94
24
72
14
47
LP
46
98
33
73
23
59
15
48
STD
47
99
27
63
18
51
STD
71
185
51
141
25
76
LP
23
70
LP
45
43
62
91 166
26
62 127
17
51
STD
50
76
90
67
78
138 152 221 136 199
40
116
30
89
17
53
LP
200 ft
21
65
LP
40
56
61
70
126 182
40
86 452
25
61 116
17
50
STD
45
75
77
66
66
59
58
101
108
89
93
80
66
124
126
108
108
—
101
93
91
81
163
163
138
28
76
62
110
115
139
167
---
—
—
---
—
—
—
—
—
—
195
—
—
195
340 340
166
33
97
LP
71
103
130
156
---
---
—
—
—
—
183
---
---
—
—
—
—
182
331 329
149
283 306
106
207 279
59
122 242
28
65 184
19
53
STD
250 ft.
(1) Number on top of each box indicates flow (GPM), and number on bottom indicates nozzle reaction (LBS). (2) In Standard mode, the average nozzle pressure is 100
PSI. (3) Flows may vary with brand or condition of hose. (4) Flows are approximate and do not reflect losses in preconnect piping.
141
---
110
---
117
---
62
---
71
223 174 196 157 177 248 269 216 241 195 218 329 328 293 303 264 283
250 199
102
91
88
77
81
67
129 122 112 102 100
89
181 181 155 154
139 134
71
—
80
—
84
—
225
—
—
—
121
126
71
242 268
75
93
79
183 209 160 184 144 166 227 255 199 226 179 205 307 311 268 287
88
179
—
91
179
—
51
149
—
56
35
65 194
19
328 326 312 315
128
—
58
119
194 145 171 131 154 204 237 179 210 162 190 273 294 240 270 217 250
200 165
83
76
72
64
64
57
105
99
91
84
81
74
144 144 125 123
112 108
63
LP
53 102
STD
245 299 223 288
66
—
68
97
47
190 230
51
72
53
146 178 128 157 116 142 179 217 158 193 143 175 238 274 210 251
60
82
206
37
107
LP
135 265 128 254
28
65
19
53
STD
200 ft
2 1/2" HOSE
250 ft. 150 ft.
80
38
82
28
65
21
56
14
45
STD
250 ft. 150 ft.
160 208
44
124
36
104
27
80
15
50
LP
200 ft
60
69
22
57
15
STD
150 ft.
2" HOSE
= STANDARD PRESSURE MODE
= LOW PRESSURE MODE
124 160 110 141 100 128 151 196 134 174 122 157 198 252 176 227
51
30
17
16
47
54
48
LP
250 ft.
1 3/4" HOSE
LP
STD
For Nozzles Manufactured After December 1, 2003
95
175
150
125
100
75
50
STD
LP
200 ft
STD
150 ft.
1 1/2" HOSE
Flow And
Nozzle Reaction Chart
CAUTION: Changing to Low Pressure mode will typically increase nozzle reaction.
PUMP DISCHARGE PRESSURE (PSI)
FLOW
(GPM)
REACTION
(LBS)
10
11
LP
7 bar
LP
75M
7 bar
LP
45M
7 bar
LP
60M
7 bar
LP
75M
45mm HOSE
7 bar
LP
45M
7 bar
LP
60M
7 bar
LP
75M
7 bar
LP
45M
7 bar
LP
60M
7 bar
LP
75M
2 1/2" HOSE
= STANDARD PRESSURE MODE
= LOW PRESSURE MODE
2" HOSE
LP
7 bar
For Nozzles Manufactured After December 1, 2003
11
15
10
14
12
23
12
20
18
15
17
24
16
20
15
18
21
32
20
28
25
18
26
29
23
25
21
23
34
41
30
35
32
32
54
28
50
27
47
58
68
52
63
48
59
927 1132 844 1090 783 1056
30
20
34
35
30
30
27
26
46
49
40
42
38
—
41
37
74
74
64
63
57
55
68
71
—
—
—
—
—
---
88
---
---
—
---
—
—
—
—
—
—
83
—
—
88
---
---
—
—
—
—
83
(1) Number on top of each box indicates flow (GPM), and number on bottom indicates nozzle reaction (LBS). (2) In Standard mode, the average nozzle pressure is 100
PSI. (3) Flows may vary with brand or condition of hose. (4) Flows are approximate and do not reflect losses in preconnect piping.
CAUTION: Changing to Low Pressure mode will typically increase nozzle reaction.
42
76
— 1287 1287 1253 1245
---
46
49
---
50
49
---
53
57
---
28
56
844 659 742 594 670 939 1018 818 912 738 825 1245 1241 1109 1147 999 1071 —
17.0 753
46
41
40
35
35
30
59
55
51
46
45
40
82
82
70
70
63
61
---
32
30
—
32
32
—
36
34
—
38
36
42
40
693 791 606 696 545 628 859 965 753 855 678 776 1162 1177 1014 1086 916 1014
41
—
23
—
25
75
—
26
81
—
29
81
734 549 647 496 583 772 897 678 795 613 719 1033 1113 908 1022 821 946
14.0 625
38
34
33
29
29
26
48
45
41
38
37
34
65
65
57
56
51
49
31
44
21
719 871
23
33
24
553 674 484 594 439 537 678 821 598 731 541 662 901 1037 795 950
27
—
15.5
13
36
17
34
606 787 1241 1234 1181 1192 1071 1158
20
13
27
19
37
511 1003 484 961 462 916
13
246 780 246 734 246 696
469 606 416 534 379 484 572 742 507 659 462 594 749 954 666 859
23
28
13
477 689
16
21
14
379 534 337 469 310 424 450 651 405 575 371 522 575 836 515 753
19
18
17
326 575
11
15
11
280 447 261 394 246 356 314 545 291 484 276 439 375 700 344 628
10
11
12
231 439
10
10
14
223 344 216 303 212 273 231 416 227 371 223 337 238 534 235 481
43
12.0
10.0
8.6
7.0
5.2
204 178 189 170 178 189 235 185 212 182 201 193 288 193 265 189 246 201 405 201 386 201 367
3.5 182
7
8
7
7
6
6
8
9
7
8
7
8
8
11
8
10
8
10
9
17
9
16
9
15
7 bar
60M
38mm HOSE
Flow And
Nozzle Reaction Chart
FLOW
(l/min)
45M
REACTION
(KG) 7 bar LP
PUMP DISCHARGE PRESSURE (bar)
9.0 INSPECTION CHECKLIST
Nozzle must be inspected for proper operation and function according to this checklist before each use.
Check that:
1) There is no obvious damage such as missing, broken or loose parts, damaged labels etc.
2) Gasket grabber is free of debris.
3) Coupling is tight and leak free.
4) Valve operates freely through full range and regulates flow.
5) "OFF" position does fully shut off and flow is stopped.
6) Nozzle flow is adequate as indicated by pump pressure and nozzle reaction.
7) Shaper turns freely and adjusts pattern through full range.
8) Shaper turns into full flush and out of flush with normal flow and pressure restored.
9) Standard/low pressure knob turns freely and changes nozzle pressure.
WARNING
Any Mid-Force or Dual-Force nozzle failing any part of the inspection checklist is
unsafe and must have the problem corrected before use. Operating a nozzle that fails
any of the above inspections is a misuse of this equipment.
TASK FORCE TIPS, Inc.
©Copyright Task Force Tips, Inc. 2002
2800 East Evans Avenue • Valparaiso , IN 46383-6940
800-348-2686 • 219-462-6161 • Fax 219-464-0620
LIN-035 July 31, 2002 Rev 6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement