Wireless Products (From Automation Catalog)

Wireless Products (From Automation Catalog)
Industrial network solutions
Factory Line Wireless
Wireless MUX IO
Wireless transmission of control
signals
The Wireless MUX is sold as a "Ready to
use" package: Unpack – connect – switch on
– and the wireless link is working.
*
The range can be considerably exceeded or fallen below and
depends on the environment, antenna technology and the product
used.
Please visit www.phoenixcontact.com for more information on the
prevailing country-specific approvals for the relevant product.
Two packages are available:
– Standard package with OMNI antenna, an
omnidirectional antenna. Ranges* of
between 50 m and 100 m in the hall and
over 200 m outdoors are thus possible.
– Package with PANEL antenna, a
directional antenna. Outdoors, with no
obstacles, distances* of over 400 m can be
bridged.
ILB BT ADIO MUX-OMNI...
Wireless set with OMNI omnidirectional antenna
u
Description
The principle is simple. The signal
connected at the input of the wireless MUX
can be output at the corresponding output
of the other Wireless MUX in a typical time
of less than 10 ms.
Omni wireless set maritime
The Wireless MUX IO is also available
with maritime approval: GL, LR and DNV.
Pcs. /
Pkt.
Type
Order No.
- Transmission capacity 16 dBm, antenna gain 2 dBi
ILB BT ADIO MUX-OMNI
2884208
1
- Transmission capacity 8 dBm, antenna gain 2 dBi
ILB BT ADIO MUX-OMNI 8
2884554
1
- Transmission capacity 4 dBm, antenna gain 2 dBi
ILB BT ADIO MUX-OMNI 4
2692270
1
Wireless MUX set, consisting of two modules with 16 digital inputs
and outputs each and two analog inputs and outputs each, two
OMNI antennas
Wireless MUX set, consisting of two modules with 16 digital inputs
and outputs each and two analog inputs and outputs each, two
PANEL antennas
- Transmission capacity 12 dBm, antenna gain 8 dBi
- Transmission capacity 0 dBm, antenna gain 8 dBi
Modular MUX
Two ILC 170 ETH 2TX are suitable for
transmitting a greater number of digital and
analog I/O signals. These are equipped with
the required software via IL MODULAR
MUX SD cards. The individual selection of
Inline I/O terminals can be aligned with the
ILC 170 ETH 2 TX.
The IO data is transmitted from one
controller to another via the Ethernet
interface. This can be done via an Ethernet
cable or Wireless via Bluetooth or WLAN
access points as well. Additional
configuration software is not required.
The digital and analog
Inline I/O terminals that
can be used on the field multiplexer
are marked in this catalog with the
adjacent logo.
210
PHOENIX CONTACT
- Transmission capacity 8 dBm, antenna gain 8 dBi
Modular MUX for ILC 170 ETH 2TX
Technical data
Wireless interface
Wireless standard
Frequency range
Transmission capacity
Antenna connection method
Antenna
Assembly instructions
Power supply for module electronics
Supply voltage
Range of supply voltages
Supply current
Digital inputs
Connection method
Number of inputs
Digital outputs
Connection method
Number of outputs
Maximum output current per channel
Protective circuitry
Analog inputs
Number of inputs
Voltage input signal
Current input signal
Measured value resolution
Analog outputs
Number of outputs
Voltage output signal
Current output signal
DAC resolution
General data
Weight
Width
Degree of protection
Ambient temperature (operation)
Shock as per IEC 60068-2-29
Vibration (operation) in acc. with IEC 60068-2-6:1982
Mounting type
Bluetooth 1.2
2.402 GHz ... 2.48 GHz (ISM bandwidth)
16 dBm (40 mW, controlled automatically)
MCX (female)
OMNI omnidirectional antenna, 2 dBi, Lambda/2, with fixing
bracket, 1.5 m cable
24 V DC
19.2 V DC ... 30 V DC (including ripple)
< 100 mA
1-wire
16
1-wire
16
500 mA
Short circuit protection, overload protection, protected against
reverse voltages
2
0 V ... 10 V
0 mA ... 20 mA
12 bits
2
0 V ... 10 V
0 mA ... 20 mA
12 bits
1200 g
95 mm
IP20
-25°C ... 60°C
25g
5g
DIN rail mounting
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370
Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Industrial network solutions
Factory Line Wireless
ILB BT ADIO MUX-PANEL ...
ILB BT ADIO MUX-OMNI/M
IL MODULAR MUX SD
Wireless set with PANEL directional antenna
Wireless set with OMNI omnidirectional antenna and maritime
approval
SD memory card with MODULAR MUX software
Applied for:
GL / LR / NV
u
Pcs. /
Pkt.
Type
Order No.
ILB BT ADIO MUX-PANEL
2884509
1
ILB BT ADIO MUX-PANEL 8
2884567
1
Type
Order No.
ILB BT ADIO MUX-OMNI 8/M
2693185
Pcs. /
Pkt.
Type
Order No.
IL MODULAR MUX SD
2700047
Pcs. /
Pkt.
1
Bluetooth 1.2
2.402 GHz ... 2.48 GHz (ISM bandwidth)
12 dBm (16 mW, controlled automatically)
MCX (female)
Bluetooth 1.2
2.402 GHz ... 2.48 GHz (ISM bandwidth)
8 dBm (6.3 mW, controlled automatically)
MCX (female)
-
PANEL radio link antenna, 8 dBi, with fixing bracket, 1 m cable
OMNI omnidirectional antenna, 2 dBi, Lambda/2, with fixing
bracket, 1.5 m cable
-
24 V DC
19.2 V DC ... 30 V DC (including ripple)
24 V DC
19.2 V DC ... 30 V DC (including ripple)
-
< 100 mA
< 100 mA
-
1-wire
16
1-wire
16
-
1-wire
16
500 mA
Short circuit protection, overload protection, protected against
reverse voltages
1-wire
16
500 mA
Short circuit protection, overload protection, protected against
reverse voltages
-
2
0 V ... 10 V
0 mA ... 20 mA
12 bits
2
0 V ... 10 V
0 mA ... 20 mA
12 bits
-
2
0 V ... 10 V
0 mA ... 20 mA
12 bits
2
0 V ... 10 V
0 mA ... 20 mA
12 bits
-
1300 g
95 mm
IP20
-25°C ... 60°C
25g
5g
DIN rail mounting
1200 g
95 mm
IP20
-25°C ... 60°C
25g
5g
DIN rail mounting
-
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370
Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PHOENIX CONTACT
1
211
Industrial network solutions
Factory Line Wireless
Wireless-IO
Factory Line Bluetooth for wireless
signal transmission
The Fieldline installation system from
Phoenix Contact can have up to three
Fieldline Modular Wireless IO modules
distributed in the field added to it via a
Bluetooth-based local bus.
There is a choice of Inline Block modules
with IP20 protection and Fieldline devices
with IP65 as IO devices.
Configuration of the devices is a simple
matter: The base station writes the
connection data to an ID connector that is
then plugged onto the wireless modules.
The basic station can be integrated in all
common fieldbus networks, such as
INTERBUS and PROFIBUS, using the
various Fieldline bus couplers.
Factory Line Modbus IO access point
The FL BT MOD IO AP allows
automation sensors and actuators to be
wirelessly integrated in an Ethernet
network.
The communication with the controller
takes place over the industrial Ethernet
protocol Modbus/TCP. The sensors and
actuators are connected to wireless IO
modules which are available in IP65 or IP20
degree of protection.
The FL BT MOD IO AP can
communicate with up to seven Wireless IO
modules at the same time.
Factory Line Bluetooth
Factory Line Bluetooth is the industrial
Bluetooth technology for transmission of
control data in factory automation.
– Extremely rugged and reliable
– Simple and fast commissioning
– Can be operated together with WLAN
without any interruptions due to the
Black-Channel-Listing, Low Emission
Mode and AFH
– Parallel operation of several Bluetooth
systems
– Manipulation-proof and tap-proof
FLM BT BS 3...
Fieldline Modular Wireless IO base station for up to three
Wireless IO devices
u
Description
Fieldline Modular Wireless IO base station for up to three
Wireless IO devices
- Adjustable transmission power
- 4 dBm transmission power
Bluetooth Modbus IO access point
PHOENIX CONTACT
Order No.
FLM BT BS 3
FLM BT BS3-4
2736770
2692681
Fieldline Modular Wireless IO device
- Adjustable transmission power
- 4 dBm transmission power
Inline Block Wireless IO device
- Adjustable transmission power
- 4 dBm transmission power
Configuration connector ID-PLUG, necessary to configure the
Wireless-IO devices (need for replacement)
DIN rail adapter
Technical data
Wireless interface
Wireless standard
Frequency range
Transmission capacity
Wireless modules that can be connected
Antenna connection method
Antenna
Type of connection
Assembly instructions
Fieldbus interface
Name
Transmission speed
Ethernet interfaces
Type of connection
Power supply for module electronics
Supply voltage
Range of supply voltages
Digital inputs
Connection method
Number of inputs
Digital outputs
Connection method
Number of outputs
Maximum output current per channel
Protective circuitry
Analog inputs
Number of inputs
Voltage input signal
Current input signal
Measured value resolution
Analog outputs
Number of outputs
Voltage output signal
Current output signal
DAC resolution
General data
Weight
Width
Degree of protection
Ambient temperature (operation)
Mounting type
212
Type
Bluetooth 1.2
2.402 GHz ... 2.48 GHz (ISM bandwidth)
8 dBm (6.3 mW, controlled automatically)
Up to 3
SMA (female)
SMA (male)
OMNI antenna is included
Fieldline Modular local bus
500 kBaud / 2 MBaud
(data rate can be changed via pin 5 (voltage supply ULS))
24 V DC
19.2 V DC ... 30 V DC (including ripple)
-
255 g
70.5 mm
IP65
-25°C ... 60°C
Wall mounting, optionally on mounting plate
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370
Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Pcs. /
Pkt.
1
1
Industrial network solutions
Factory Line Wireless
FL BT MOD IO AP
FLM BT DIO 8/8 M12...
ILB BT ADIO 2/2/16/16...
Bluetooth Modbus IO access point,
as a wireless access point for Wireless IO devices
Fieldline Modular Wireless IO device for connection with
FLM BT BS 3 and FL BT MOD IO AP
Inline Block Wireless IO device for connection with FLM BT BS 3
and FL BT MOD IO AP
U
Ex: u
Type
Order No.
FL BT MOD IO AP
2884758
Pcs. /
Pkt.
u
Type
Order No.
FLM BT DIO 8/8 M12
FLM BT DIO 8/8-M12-4
2736767
2692694
2884949
u
Pcs. /
Pkt.
Type
Order No.
ILB BT ADIO 2/2/16/16
ILB BT ADIO 2/2/16/16-4
2884282
2692704
1
1
FLM BT ID-PLUG M12
2736783
1
1
FLM BT ID-PLUG M12
FL BT ADAPTER
Pcs. /
Pkt.
2736783
1
1
1
1
Bluetooth 2.0
ISM 2.4 GHz
Max. 14 dBm (with automatic control)
7 (FLM BT DIO 8/8 M12, ILB BT ADIO 2/2/16/16)
SMA (female)
Bluetooth 1.2
2.402 GHz ... 2.48 GHz (ISM bandwidth)
8 dBm (6.3 mW, controlled automatically)
1 (FLM BT BS 3, FL BT MOD IO AP)
SMA (female)
Bluetooth 1.2
2.402 GHz ... 2.48 GHz (ISM bandwidth)
8 dBm (6.3 mW, controlled automatically)
1 (FLM BT BS 3, FL BT MOD IO AP)
SMA (female)
SMA (male)
External OMNI omnidirectional antenna, antennas can be
exchanged
SMA (male)
OMNI antenna is included
SMA (male)
OMNI antenna is included
-
-
-
RJ45 female connector
-
-
24 V DC
9 V DC ... 30 V DC
24 V DC
19.2 V DC ... 30 V DC (including ripple)
24 V DC
19.2 V DC ... 30 V DC (including ripple)
-
2, 3-wire
8
1-wire
16
-
2, 3-wire
8
500 mA
Short circuit protection, overload protection, protected against
reverse voltages
1-wire
16
500 mA
Short circuit protection, overload protection, protected against
reverse voltages
-
-
2
0 V ... 10 V
0 mA ... 20 mA
12 bits
-
-
2
0 V ... 10 V
0 mA ... 20 mA
12 bits
95 g
80 mm
IP20
-25°C ... 55°C
Wall mounting, DIN rail mounting optional
310 g
70.5 mm
IP65
-25°C ... 60°C
Wall mounting, optionally on mounting plate
305 g
117 mm
IP20
-25°C ... 60°C
DIN rail mounting
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370
Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PHOENIX CONTACT
213
Industrial network solutions
Factory Line Wireless
Factory Line Bluetooth
Factory Line Bluetooth for wireless
transmission of control data
For wireless integration of Ethernetcompatible automation components in the
network, the Factory Line module offer
FL BLUETOOTH AP and FL BT EPA. The
data is transferred transparently according
to the protocol. This allows industrial
Ethernet protocols, such as Modbus/TCP,
Ethernet/IP and PROFINET to be reliably
transmitted.
The FL BLUETOOTH AP can be used as
an access point for up to seven devices, as
an Ethernet client adapter and as a serial
Bluetooth COM server.
The FL BT SPA is a Bluetooth serial
adapter with which serial devices can be
wirelessly integrated in an Ethernet
network via the FL BLUETOOTH AP and its
integrated COM server.
*
The range can be considerably exceeded or fallen below and
depends on the environment, antenna technology and the product
used.
Please visit www.phoenixcontact.com for more information on the
prevailing country-specific approvals for the relevant product.
FL BLUETOOTH AP
Bluetooth access point,
can be used as an access point or a client
U
Ex: u
Description
Pcs. /
Pkt.
Type
Order No.
FL BLUETOOTH AP
2737999
1
FL BT ADAPTER
2884949
1
Bluetooth access point
Bluetooth Ethernet client adapter
Protocol-transparent Ethernet wireless path
FL BT EPA
The new concept of "intelligent antenna"
combines all functions in one extremely
compact and rugged IP65 housing: an
industrial Bluetooth wireless module,
circular special antenna for reliable wireless
connections in metallic environments and
control electronics that provides the PLC
with complete control over all functions.
Thanks to this concept, a better, more
high-performance and considerably
economically installation can be
automatically attained.
With the new "Lean-Stacks", the FL BT
EPA speed is more than double as
compared to the previous solutions. The FL
BT EPA fulfills the PROFINET requirements
of Conformance Class A.
The FL BT EPA AIR SET is a "Ready to
use" package: Unpack, connect, press the
Mode button and the wireless path is ready
to work in just a few seconds!
Factory Line Bluetooth
Factory Line Bluetooth is the industrial
Bluetooth technology from Phoenix
Contact for transmission of control data in
factory automation.
– Extremely rugged and reliable
– Simple and fast commissioning
– Can be operated together with WLAN
without any interruptions due to the
Black-Channel-Listing, Low Emission
Mode and AFH
– Parallel operation of several Bluetooth
systems
– Manipulation-proof and tap-proof
214
PHOENIX CONTACT
Bluetooth serial port adapter
DIN rail adapter
Technical data
Wireless interface
Wireless standard
Frequency range
Transmission capacity
Wireless modules that can be connected
Profiles supported
Antenna connection method
Antenna
Type of connection
Assembly instructions
Ethernet interfaces
Type of connection
Serial port
Type of connection
Protocols supported
Power supply for module electronics
Supply voltage
Type of connection
Range of supply voltages
Supply current
Security
Bluetooth 2.0
ISM 2.4 GHz
Max. 14 dBm (with automatic control)
7
LAP, PAN, SPP
SMA (female)
SMA (male)
External OMNI omnidirectional antenna, antennas can be
exchanged
RJ45 female connector
D-SUB-9 connector
RS-232
24 V DC
Via COMBICON
9 V DC ... 30 V DC
200 mA
128 bit data encoding
MAC filter
Authentication
PIN
Non-discoverable
Function
Operating modes
Function
Configuration
General data
Radio (wireless) certifications
Weight
Width
Height
Depth
Degree of protection
Class of protection
Ambient temperature (operation)
Permissible humidity (operation)
Air pressure (operation)
Mounting type
Access point / Ethernet client adapter / (COM server)
Bridge, P2P, MP, COM server
Web-based management
Europe, more countries in e-shop
95 g
80 mm
65 mm
25 mm
IP20
III
-30°C ... 65°C
5% ... 90% (non-condensing)
795 hPa ... 1080 hPa (up to 2000 m above mean sea level)
Wall mounting, DIN rail mounting optional
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370
Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Industrial network solutions
Factory Line Wireless
FL BT EPA
FL BT EPA AIR SET
FL BT SPA
Bluetooth Ethernet client adapter for wireless connection of
Ethernet termination devices to an FL BLUETOOTH AP
Protocol-transparent Ethernet spark gap, e.g. for PROFINET,
Modbus/TCP etc.
Bluetooth serial port adapter,
as a wireless connection for a serial interface to
FL BLUETOOTH AP
Type
Order No.
FL BT EPA
2692788
FL BT ADAPTER
2884949
Pcs. /
Pkt.
Type
Order No.
FL BT EPA AIR SET
2693091
Pcs. /
Pkt.
Pcs. /
Pkt.
Type
Order No.
FL BT SPA
2884952
1
FL BT ADAPTER
2884949
1
1
1
FL BT ADAPTER
2884949
1
1
Bluetooth 2.0
ISM 2.4 GHz
Max. 20 dBm (with automatic control)
1
PAN
-
Bluetooth 2.0
ISM 2.4 GHz
Max. 20 dBm (with automatic control)
1
PAN
-
Bluetooth 2.0
ISM 2.4 GHz
Max. 14 dBm (with automatic control)
1
SPP
SMA (female)
Permanently installed
Internal circularly polarized panel antenna
Permanently installed
Internal circularly polarized panel antenna
SMA (male)
External OMNI omnidirectional antenna, antennas can be
exchanged
M 12 connectors (D-coded, female)
M 12 connectors (D-coded, female)
-
-
-
D-SUB-9 connector
RS-232, RS-485, RS-422
24 V DC
M12 connector (A-coded, male)
9 V DC ... 30 V DC
-
24 V DC
M12 connector (A-coded, male)
9 V DC ... 30 V DC
-
24 V DC
Via COMBICON
9 V DC ... 30 V DC
200 mA
128 bit data encoding
Authentication
PIN
Non-discoverable
128 bit data encoding
Authentication
PIN
Non-discoverable
128 bit data encoding
MAC filter
Authentication
PIN
Non-discoverable
Ethernet client adapter
Ethernet client adapter
Serial client adapters
Client, bridge, P2P
Web-based management
Client, bridge, P2P
Web-based management
Serial port adapter
By means of AT commands
Europe, more countries in e-shop
120 g
66 mm
91 mm
34 mm
IP65
III
-30°C ... 65°C
5% ... 90% (non-condensing)
795 hPa ... 1080 hPa (up to 2000 m above mean sea level)
Wall mounting
Europe, more countries in e-shop
500 g
66 mm
91 mm
34 mm
IP65
III
-30°C ... 65°C
5% ... 90% (non-condensing)
795 hPa ... 1080 hPa (up to 2000 m above mean sea level)
Wall mounting
Europe, more countries in e-shop
95 g
80 mm
65 mm
25 mm
IP20
III
-25°C ... 55°C
5% ... 90% (non-condensing)
795 hPa ... 1080 hPa (up to 2000 m above mean sea level)
Wall mounting, DIN rail mounting optional
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370
Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PHOENIX CONTACT
215
Industrial network solutions
Factory Line Wireless
Factory Line WLAN
Reliable, rugged and safe. Factory Line
WLAN access points have been specially
designed for use in harsh industrial
environments. By supporting the currently
highest safety standard in acc. with IEEE
802.11i with AES encoding, the data are
protected as best possible from
unauthorized access or manipulation.
The Factory Line access points thus
enable mobile applications to have reliable
and safe wireless network access, or
guarantee stable connections to outlying
stations over several hundred meters.
The Factory Line access points fulfill the
PROFINET requirements of Conformance
Class A.
*
The range can be considerably exceeded or fallen below and
depends on the environment, antenna technology and the product
used.
Please visit www.phoenixcontact.com for more information on the
prevailing country-specific approvals for the relevant product.
FL WLAN ... AP 802-11
Wireless LAN access point
for the b, g, a and h wireless standards
Pcs. /
Pkt.
Description
Type
Order No.
Wireless LAN access point
- One wireless interface, two antennas
- Two wireless interfaces, four antennas
- Supply voltage 230 V AC
Replaceable configuration memory for WLAN modules
FL WLAN 24 AP 802-11
FL WLAN 24 DAP 802-11
FL WLAN 230 AP 802-11
2884075
2884279
2884444
1
1
1
2692539
1
FL WLAN SIM
Technical data
Wireless interface
Wireless standard
Frequency band
Transmission capacity
Antenna connection method
Antenna
Type of connection
Assembly instructions
FL WLAN 24 AP 802-11
IEEE 802.11 b/g/a/h
ISM 2.4 GHz / 5 GHz
20 dBm (EIRP)
R-SMA (male)
R-SMA (female)
External OMNI omnidirectional antenna, the antennas can be
exchanged
Ethernet interfaces
Type of connection
Power supply for module electronics
Supply voltage
Type of connection
Range of supply voltages
Supply current
Security
FL WLAN 230 AP 802-11
RJ45 female connector
24 V DC (PoE)
230 V AC (PoE)
Via COMBICON
18.5 V DC ... 30.5 V DC
110 V AC ... 230 V AC
400 mA (recommended protection 2AT)
WEP 64 bit/128 bit
WEPplus
WPA TKIP
802.11i WPA2 (RSN, AES)
WPA PSK (preshared key)
WPA group & master rekeying
Function
Operating modes
Configuration
Automatic channel selection
Quality of service (QoS)
Virtual LAN (VLAN) support 802.1Q
General data
Radio (wireless) certifications
Weight
Width
Height
Depth
Degree of protection
Ambient temperature (operation)
Permissible humidity (operation)
Air pressure (operation)
Shock in acc. with IEC 60068-2-27:1997
Vibration (operation) in acc. with IEC 60068-2-6:1982
Mounting type
216
PHOENIX CONTACT
Access point
Multilingual web-based interface (German/English) under http or
https, with password protection
Yes
Yes
Yes
Europe, more countries in e-shop
1300 g
159 mm
250 mm
65 mm
IP65
-20°C ... 55°C
10% ... 85% (non-condensing)
795 hPa ... 1080 hPa (up to 2000 m above mean sea level)
25g
5g
Adapter plate
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370
Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Industrial network solutions
Factory Line Wireless
Factory Line WLAN
The FL WLAN 24 AP 802-11 XDB is
suitable for control cabinet assembly due to
its compact design. It supports the Access
Point, Multipoint Bridge and Client Adapter
operating modes. A Repeater Mode for
range expansion is also available.
Factory Line WLAN is the industrial
WLAN technology from Phoenix
Contactor for high-performance
infrastructure networks and for control of
mobile transport systems
– High performance and reliability
– Long range
– Good integration in automation systems
– Manipulation-proof and tap-proof
... 802-11 XDB
Wireless LAN access point
For the a, b and g wireless standards
Ex: U
Description
Wireless LAN access point
- One wireless interface approved for Europe, antennas as
accessories
Wireless LAN access point
- One wireless interface approved for USA, antennas as
accessories
Technical data
Wireless interface
Wireless standard
Frequency band
Transmission capacity
Antenna connection method
Antenna
Assembly instructions
Ethernet interfaces
Type of connection
Power supply for module electronics
Supply voltage
Type of connection
Range of supply voltages
Supply current
Security
Pcs. /
Pkt.
Type
Order No.
FL WLAN 24 AP 802-11 XDB
2990037
1
RAD-80211-XDB
2990011
1
FL WLAN 24 AP 802-11 XDB
RAD-80211-XDB
IEEE 802.11 a/b/g
ISM 2.4 GHz / 5 GHz
20 dBm (EIRP)
2x MCX (female)
Antenna not included
RJ45 female connector
24 V DC
Via COMBICON
9 V DC ... 30 V DC
215 mA (24 V DC)
WEP 64 bit/128 bit
WPA TKIP
802.11i WPA2 (AES)
WPA PSK (preshared key)
Function
Operating modes
Configuration
Automatic channel selection
General data
Radio (wireless) certifications
Weight
Width
Height
Depth
Degree of protection
Ambient temperature (operation)
Permissible humidity (operation)
Air pressure (operation)
Shock in acc. with IEC 60068-2-27:1997
Vibration (operation) in acc. with IEC 60068-2-6:1982
Mounting type
access point, client, bridge
Web-based management
Yes
Europe, more countries in
e-shop
Americas, more countries in
e-shop
250 g
45 mm
99 mm
113 mm
IP20
0°C ... 65°C
5% ... 90% (non-condensing)
795 hPa ... 1080 hPa (up to 2000 m above mean sea level)
25g
5g
DIN rail mounting
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370
Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PHOENIX CONTACT
217
Industrial network solutions
Factory Line Wireless
Wireless Ethernet
Factory Line WLAN client for
network integration and fast roaming
Reliable, rugged and safe. The Factory
Line Ethernet and Serial Port adapters have
been specially designed for use in harsh
industrial environments.
They allow integration of automation
devices and PLCs to serial or Ethernet
connection to a WLAN network. By
supporting the currently highest safety
standard in acc. with IEEE 802.11i with AES
encoding, the data are protected as best
possible from unauthorized access or
manipulation.
Bridge mode and fast roaming in
automation networks
With its high performance and fully
transparent bridge operating mode, the
WLAN client FL WLAN 24 EC 802-11 in
combination with a suitable access point is
ideal for a powerful and inexpensive
connection of two networks (Layer 2
transparent) over several hundred meters.
Factory Line WLAN client FL WLAN 24
EC 802-11 implements various standardcompliant functions that enable extremely
fast and reliable roaming.
– Standard roaming:
Fastest possible roaming through
unlimited channel lists and configurable
signal threshold values (RSSI)
– Table roaming:
Configurable fixed sequence of access
points e.g. for linear vehicle systems and
Modbus/TCP API for controlled access
point change
The FL WLAN EPA/SPA module
stands out with the following features:
– Protocol-transparent data transmission
– Brief delay time (Latent)
– Fast setting up of the connection
– Configuration, diagnostics and
connection control via SNMP (only FL
WLAN EPA) and AT commands
– DHCP server and client
– Operating modes: Infrastructure and Adhoc
– Ad-hoc networks with seven devices can
be realized
218
PHOENIX CONTACT
The "intelligent antenna" concept
The new concept of "intelligent antenna"
for FL WLAN EPA combines all functions in
one extremely compact and rugged IP65
housing: industrial WLAN wireless module,
circular special antenna for reliable wireless
connections in metallic environments and
control electronics that provides the PLC
with complete control over all functions.
Thanks to this concept, a better, more
high-performance and considerably
economically installation can be
automatically attained.
Factory Line WLAN is the industrial
WLAN technology from Phoenix
Contactor for high-performance
infrastructure networks and for control of
mobile transport systems
– High performance and reliability
– Long range
– Good integration in automation systems
– Manipulation-proof and tap-proof
Description
Wireless LAN Ethernet client
Wireless LAN Ethernet port adapter
Wireless LAN serial port adapter,
Replaceable configuration memory for WLAN modules
Technical data
Wireless interface
Wireless standard
Frequency band
Transmission capacity
Antenna connection method
Antenna
Type of connection
Assembly instructions
Ethernet interfaces
Type of connection
Serial port
Type of connection
Protocols supported
Power supply for module electronics
Supply voltage
Type of connection
Range of supply voltages
Supply current
Security
Function
Operating modes
Configuration
Automatic channel selection
Quality of service (QoS)
Virtual LAN (VLAN) support 802.1Q
General data
Radio (wireless) certifications
Weight
Width
Height
Depth
Degree of protection
Ambient temperature (operation)
Permissible humidity (operation)
Air pressure (operation)
Shock in acc. with IEC 60068-2-27:1997
Vibration (operation) in acc. with IEC 60068-2-6:1982
Mounting type
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370
Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Industrial network solutions
Factory Line Wireless
FL WLAN 24 EC 802-11
FL WLAN EPA
FL WLAN SPA
Ethernet client adapter
for the b, g, a and h wireless standards
Wireless LAN Ethernet port adapter,
as a wireless connection for an Ethernet interface to a WLAN
access point
Wireless LAN serial port adapter,
as a wireless connection for a serial interface to a WLAN access
point
Type
Order No.
FL WLAN 24 EC 802-11
2884130
FL WLAN SIM
Pcs. /
Pkt.
2692539
Type
Order No.
FL WLAN EPA
2692791
Pcs. /
Pkt.
Type
Order No.
FL WLAN SPA
2884761
Pcs. /
Pkt.
1
1
1
1
IEEE 802.11 b/g/a/h
ISM 2.4 GHz / 5 GHz
20 dBm (EIRP)
R-SMA (male)
IEEE 802.11 b/g
ISM 2.4 GHz
Max. 20 dBm (EIRP)
-
IEEE 802.11 b/g
ISM 2.4 GHz
14 dBm (EIRP)
SMA (male)
R-SMA (female)
External OMNI omnidirectional antenna, the antennas can be
exchanged
Permanently installed
Internal circularly polarized panel antenna
SMA (female)
Exchangeable
RJ45 female connector
M 12 connectors (D-coded, female)
-
-
-
D-SUB-9 connector
RS-232, RS-485, RS-422
24 V DC (PoE)
Via COMBICON
18.5 V DC ... 30.5 V DC
400 mA (recommended protection 2AT)
24 V DC
M12 connector (A-coded, male)
9 V DC ... 30 V DC
-
24 V DC
Via COMBICON
9 V DC ... 30 V DC
200 mA
WEP 64 bit/128 bit
WEPplus
WPA TKIP
802.11i WPA2 (RSN, AES)
WPA PSK (preshared key)
WPA group & master rekeying
802.11i
WPA PSK (preshared key)
WPA2 PSK
AES
WEP 64 bit/128 bit
TKIP
802.11i
WPA PSK (preshared key)
WPA2 PSK
AES
WEP 64 bit/128 bit
TKIP
Ethernet client adapter
Ethernet client adapter
Client adapters
Multilingual web-based interface (German/English) under http or
https, with password protection
Web-based management
By means of AT commands
Yes
Yes
Yes
Yes
-
Yes
-
Europe, more countries in e-shop
1300 g
159 mm
250 mm
65 mm
IP65
-20°C ... 55°C
10% ... 85% (non-condensing)
795 hPa ... 1080 hPa (up to 2000 m above mean sea level)
25g
5g
Adapter plate
Europe, more countries in e-shop
120 g
66 mm
91 mm
34 mm
IP65
-30°C ... 65°C
5% ... 90% (non-condensing)
795 hPa ... 1080 hPa (up to 2000 m above mean sea level)
Wall mounting
Europe, more countries in e-shop
95 g
80 mm
65 mm
25 mm
IP65
-25°C ... 55°C
5% ... 90% (non-condensing)
795 hPa ... 1080 hPa (up to 2000 m above mean sea level)
25g
5g
Wall mounting, DIN rail mounting optional
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370
Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PHOENIX CONTACT
219
Industrial network solutions
Factory Line Wireless
2.4 GHz accessories
RAD-ISM-2400-ANT-PAN-8-0
Radio link antenna with high gain (+8 dBi)
for transmitting over long distances.
RAD-ISM-2400-ANT-CIR-8-0
Circularly polarized panel directional
antenna especially for use in industrial halls
with a very high reflection component due
to metal.
PANEL directional antenna
Description
Type
Order No.
PANEL directional wireless antenna (without cable)
8 dBi, linearly polarized
8 dBi, circularly polarized, clockwise
RAD-ISM-2400-ANT-PAN- 8-0
2867610
Technical data
Ambient temperature (operation)
Degree of protection
Gain
Impedance
Type of connection
Horizontal / vertical apex angle
Dimensions W / H
Frequency range
Scope of delivery
PANEL directional antenna, circular
Pcs. /
Pkt.
Type
Order No.
RAD-ISM-2400-ANT-CIR-8-0
2884936
Pcs. /
Pkt.
1
-40°C ... 75°C
IP55
8 dBi
50 Ω
SMA (female)
75 ° / 70 °
80 mm / 100 mm
2.3 GHz ... 2.8 GHz
Incl. mounting material
1
-40°C ... 80°C
IP55
8 dBi
50 Ω
SMA (female)
70 ° / 65 °
95 mm / 101 mm
2.4 GHz
Incl. mounting material
RAD-ISM-2400-ANT-OMNI-5-0
Omnidirectional antenna with high gain
for use in buildings.
RAD-ISM-2400-ANT-OMNI-6-0
Omnidirectional antenna with high gain
for outdoors.
RAD-ISM-2400-ANT-VAN-3-...
Robust omnidirectional antenna in an
inconspicuous design with vandalism
protection.
OMNI omnidirectional antenna OMNI omnidirectional antenna
Description
Type
Order No.
OMNI omnidirectional antenna
2.4 Ghz, 5 dBi gain
2.4 Ghz, 6 dBi gain
OMNI omnidirectional antenna with vandal protection
RAD-ISM-2400-ANT-OMNI-5-0
RAD-ISM-2400-ANT-OMNI-6-0
2884923
2885919
Pcs. /
Pkt.
Technical data
RAD-ISM-2400-ANT-OMNI-5-0
RAD-ISM-2400-ANT-OMNI-6-0
Ambient temperature (operation)
Degree of protection
Gain
Impedance
Type of connection
Horizontal / vertical apex angle
Dimensions W / H
Frequency range
Scope of delivery
-20°C ... 65°C
IP55
5 dBi
50 Ω
SMA (male)
360 ° / 45 °
13 mm / 187 mm
2.4 GHz
-
-40°C ... 75°C
IP55
6 dBi
50 Ω
N (female)
360 ° / 30 °
22 mm / 250 mm
2.4 GHz ... 2.5 GHz
Incl. mounting material
PHOENIX CONTACT
Order No.
RAD-ISM-2400-ANT-VAN- 3-0-SMA
RAD-ISM-2400-ANT-VAN- 3-1-MCX
RAD-ANT-VAN-MKT
2885867
2885702
2885870
Pcs. /
Pkt.
1
1
With SMA connection (male)
With connection MCX (male)
Mounting material
220
Type
RAD-ISM-2400-ANT-VAN- 3-0SMA
-40°C ... 80°C
IP55
3 dBi
50 Ω
SMA (male) with cable (1.5 m)
360 ° / 85 °
86 mm / 43 mm
2.4 GHz
-
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370
Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
1
1
1
RAD-ISM-2400-ANT-VAN- 3-1MCX
-40°C ... 80°C
IP55
3 dBi
50 Ω
MCX (male) with cable (1.5 m)
360 ° / 85 °
86 mm / 43 mm
2.4 GHz
-
Industrial network solutions
Factory Line Wireless
5 GHz accessories
RAD-ISM-5000-ANT-PAR-18-N
RAD-ISM-5000-ANT-PAR-22-N
Directional wireless antennas for
WLAN 802.11a (5 GHz) with high profits
for larger distances.
Parabolic antenna
Description
Type
Order No.
Parabolic antenna
Gain 18 dBi
Gain 22 dBi
RAD-ISM-5000-ANT-PAR-18-N
5606613
Technical data
Ambient temperature (operation)
Degree of protection
Gain
Impedance
Type of connection
Horizontal / vertical apex angle
Dimensions W / H
Frequency range
Scope of delivery
Parabolic antenna
Pcs. /
Pkt.
Type
Order No.
RAD-ISM-5000-ANT-PAR-22-N
5606174
Pcs. /
Pkt.
1
-40°C ... 70°C
IP55
18 dBi
50 Ω
N (female)
18 ° / 18 °
152.4 mm / 152.4 mm
5.25 GHz ... 5.85 GHz
Incl. mounting material
1
-40°C ... 70°C
IP55
22 dBi
50 Ω
N (female)
12 ° / 12 °
-/5.25 GHz ... 5.85 GHz
Incl. mounting material
Omnidirectional antenna for 5 GHz for
direct assembly on WLAN devices with
R-SMA connection (replacement part).
OMNI omnidirectional antenna
Description
Type
Order No.
Omnidirectional antenna
5 GHz, 5 dBi gain
RAD-ISM-5200-ANT-OMNI-5-0
2692034
Technical data
Ambient temperature (operation)
Degree of protection
Gain
Impedance
Type of connection
Horizontal / vertical apex angle
Dimensions W / H
Frequency range
Scope of delivery
-40°C ... 80°C
IP65
5 dBi
50 Ω
RSMA (female)
360 ° / 17 °
- / 176 mm
5.2 GHz ... 5.8 GHz
-
Pcs. /
Pkt.
2
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370
Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PHOENIX CONTACT
221
Industrial network solutions
Factory Line Wireless
Antenna cables, adapters and surge
protection
RAD-CAB-EF142-...
Extension cable for positioning antennas
at a distance: leading out of the control
cabinet, connection to an antenna mounted
somewhere else.
RAD-CAB-EF393-...
When using surge protection or for
adapting an antenna with N connection
Antenna cable type EF 142
Description
Type
Order No.
RAD-CAB-EF142-3M
RAD-CAB-EF142-5M
2884512
2884525
Antenna cable type EF 393
Pcs. /
Pkt.
Type
Order No.
RAD-CAB-EF393- 3M
RAD-CAB-EF393- 5M
RAD-CAB-EF393-10M
2867649
2867652
2867665
Pcs. /
Pkt.
Antenna extension cable, SMA connection at both ends (male)
3m
5m
Antenna extension cable
3m
5m
10 m
Technical data
Ambient temperature (operation)
Impedance
Cable, attenuation
1
1
-40°C ... 105°C
50 Ω
Approx. 0.93 dB/m
1
1
1
-40°C ... 105°C
50 Ω
approx. 0.45 dB/m
RAD-PIG-EF316...
For converting connector standards or
leading out from the control cabinet.
RAD-ADP-...
As an adapter between devices and
cables.
CN-LAMBDA/4-…
Surge protection outdoors. For details,
see the TRABTECH catalog.
Description
Adapter cables (pigtails)
0.3 m, N (female) -> SMA (male)
0.5 m, SMA (male) -> SMA (male)
1 m, MCX (male) -> SMA (male)
Adapter
SMA (female) -> SMA (female)
RSMA (female) > SMA (female)
SMA (female) -> SMA (female), perpendicular
Adapter
Adapter cable, type EF 316
Type
Order No.
RAD-PIG-EF316-N-SMA
RAD-PIG-EF316-SMA-SMA
RAD-PIG-EF316-MCX-SMA
2867694
2885618
2867678
Pcs. /
Pkt.
Pcs. /
Pkt.
Type
Order No.
RAD-ADP-SMA/F-SMA/F
RAD-ADP-RSMA/F-SMA/F
RAD-ADP-SMA/F-SMA/M-90
2884541
2884538
2917324
1
1
1
CN-LAMBDA/4-2.0-BB
CN-LAMBDA/4-2.0-SB
CN-LAMBDA/4-5.9-BB
2818863
2818876
2838490
1
1
1
1
1
1
COAXTRAB, protective adapter for antenna connections
N (female) -> N (female)
N(male) -> N(female)
Female-female
Further information on surge protection can be found in the
TRABTECH catalog.
Technical data
Ambient temperature (operation)
Impedance
Cable, attenuation
Attenuation
222
PHOENIX CONTACT
-40°C ... 70°C
50 Ω
approx. 1.5 dB/m
-
-65°C ... 165°C
50 Ω
0.3 dB
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370
Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Industrial network solutions
Factory Line Wireless
Leaky waveguide and accessories
FL LCX CABLE METER
The leaky waveguide is a cable that acts as
an antenna which constantly radiates over
its length. It ensures a continuous wireless
connection when using tracked systems,
even in remote or difficult to access areas.
The cable is individually configured during
assembly and is provided with connectors.
Leaky wave conductors
Description
Type
Order No.
FL LCX CABLE METER
2884774
Connectors
Pcs. /
Pkt.
Pcs. /
Pkt.
Type
Order No.
FL LCX CON-N/F
2884965
1
FL LCX 50-OHM
2884978
1
Leaky wave conductors
1
Connectors for leaky wave conductor
Termination resistors for leaky wave conductor
Technical data
Ambient temperature (operation)
Degree of protection
Impedance
Type of connection
Frequency range
-40°C ... 85°C
50 Ω
2.4 GHz ... 6 GHz
50 Ω
N (female)
2.4 GHz ... 6 GHz
Accessories for leaky waveguide
Cable fastenings are required for
mounting the leaky waveguide and an
alignment tool is required for mounting the
connector for connecting the wireless unit.
Cable tie
Alignment tool
Description
Type
Order No.
FL LCX TOOL
2884981
Pcs. /
Pkt.
Type
Order No.
Pcs. /
Pkt.
FL LCX CLAMP
2884994
100
Alignment tool for leaky wave conductor
1
Cable tie for leaky wave conductor
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370
Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
PHOENIX CONTACT
223
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising