Baby Trend Nursery Center Instruction manual

Baby Trend Nursery Center Instruction manual
Read all instructions BEFORE assembly and USE of product.
KEEP INSTRUCTIONS FOR FUTURE USE.
Model #8166BC
SAFAri babies Trend Nursery Center
Instruction Manual
Convenience through Innovation and thoughtful design
08.06
SAFAri babies Trend Nursery Center
Read all instructions BEFORE assembly and
USE of Playard. KEEP
INSTRUCTIONS FOR FUTURE USE.
WARNING: FAILURE TO FOLLOW THESE WARNINGS AND
THE ASSEMBLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR
DEATH FROM ENTRAPMENT, STRANGULATION, SUFFOCATION, ETC.
WARNING: INFANTS CAN SUFFOCATE: IN GAPS BETWEEN
A MATTRESS TOO SMALL OR TOO THICK AND PRODUCT SIDES, ON
SOFT BEDDING. NEVER ADD A MATTRESS, PILLOW, COMFORTER, OR
PADDING. USE ONLY THE MATTRESS PROVIDED BY MANUFACTURER.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep, unless
otherwise advised by your physician.
• IF REFINISHING, USE A NONTOXIC FINISH SPECIFIED FOR CHILDREN’S PRODUCTS.
• DO NOT LEAVE CHILD IN PRODUCT WITH SIDE LOWERED.
• BE SURE SIDE IS IN RAISED AND LOCKED POSITION WHENEVER CHILD IS IN PRODUCT.
• The Playard, including side rails, must be fully erect prior to use. Make sure locks are secure.
• Discontinue use of the Playard when child is able to climb out or reaches the height of 35 inches (890 mm)
or the weight of 30 lbs.. (14 kg)
• When child is able to pull to a standing position, remove bumper pads, large toys, and other objects that
could serve as steps for climbing out.
• Always provide the supervision necessary for the continued safety of your child. When used for playing,
never leave child unattended.
• Strings can cause strangulation! DO NOT place items with a string around the child’s neck, such as hood
strings or pacifier cords. DO NOT suspend strings over a Playard/crib or attach strings to toys.
• DO NOT place the Playard near a window where cords from blinds or drapes can strangle a child. DO NOT
add padding or other objects inside the Playard that will permit your child to climb out. Keep Playard away
from stoves, heaters, campfires and other hazards.
• Never use plastic shopping bags or other plastic film as mattress covers not sold and intended for that
purpose. They can cause suffocation.
• Before each usage or assembly, inspect product for damaged hardware, loose joints, missing parts, or sharp
edges. DO NOT use Playard if any parts are missing or broken. Please contact Baby Trend Customer
Service for replacement parts, repair or instructional literature if needed. DO NOT substitute parts.
• DO NOT use a water mattress with this product.
• This product is not intended for commercial use.
MAINTENANCE AND CLEANING INSTRUCTIONS: *Use only household soap or detergent and
warm water. *NO BLEACH.
Please: If you experience any difficulty with the use of our product or have a question regarding these
instructions, please contact our Customer Service Department at (800) 328-7363 between the hours of
8:00 a.m. and 4:30 p.m. Pacific Standard Time. Please do not return the product to the store as once it is
returned it cannot be re-sold and the materials and energy used to make it are wasted.
To Contact Us:
Baby Trend, Inc.
1567 S. Campus Ave.
Ontario, CA 91761
Customer Service Hot Line
(800) 328-7363
8:00 a.m. to 4:30 p.m. Pacific Standard Time
2
FOR THE SAFETY OF YOUR CHILD, PLEASE READ THE INSTRUCTIONS COMPLETELY
BEFORE ASSEMBLING THE PLAYARD, BASSINET AND CHANGING AREA
TO ASSEMBLE PLAYARD
CONTENTS (Fig. 1-1):
1
1
2
2
1
Playard
Mattress
Leg extensions (1 Left,1 Right)
Leg extensions with wheels (1 Left, 1 Right)
Travel or Storage bag
Figure 1-1.
BEFORE YOU BEGIN: The Baby Trend Playard is designed so that,
when properly setup, the fabric of the playard places pressure on the 4
top rails making them nearly impossible to unlock. This safety feature
is activated when you push down on the playard floor to lock the bottom
rails. When setting up the playard, if you allow the bottom rails to lock
before locking the top rails, the fabric pressure will not allow you to lock
the top rails. Please see (Fig. 9.) for the proper position of the bottom of
the playard when locking the top rails.
1. Unzip bag and remove Playard frame (Fig. 1). Undo the 3 hook and
loop straps and set mattress aside (Fig. 2).
2. Turn the playard upside down. (Fig. 3). Push each leg extension into
the bottom of the leg until both sides of extension snap into place. (Fig.
4). Check that the extension is firmly connected. Attach the wheels to
the playard with the axle and nut as shown in figure (Fig. 5). The brake
cluster on the wheel must face to the inside. The axle is inserted from
the outside to the inside. (Fig. 6). Check that the wheels are firmly
connected.
3. Stand Playard on legs keeping feet of playard close together as shown in
(Fig. 7). Pull up on top rails until all rails “click” and “lock”.
Figure 1.
Figure 2.
Leg extensions
* READ IMPORTANT: In order to continue, the handle in the center
of the floor of the Playard MUST remain raised in order for the
rail to lock (approx. 45.7 cm or 18 inches). The feet of the playard
should almost touch each other. All 4 bottom rails must be pointed
upward in order to LOCK top rails.
4. Push down on center of Playard floor until it is flat and locks into
position (Fig. 8). The center lock mechanism will lock automatically.
The center lock will rotate clockwise about 90 degrees as it locks.
NOTE: Test rails to make sure they are locked. Push down on each
rail making sure they are rigid and in a set position.
Wheels
Figure 3
3
WARNING: All top rails MUST be
straight and locked in position or child may
become entrapped and suffocate.
See figure 9 and 10.
5. Place mattress in Playard with padded side up (Fig. 11).
NOTE: DO NOT insert mattress if using bassinet feature. Go to
bassinet instructions.
6.
Left
Figure 4
Right
Feed the 6 hook and loop straps (found underneath the mattress), 3 on
each end of the mattress pad, through the slots on the bottom of the
sides of the Playard. Fasten the hook and loop tabs to the underside
of Playard to prevent the mattress from moving (Fig. 12) (Fig. 13).
WARNING:
To prevent child from
suffocating, hook and loop straps MUST be
secured to underside of Playard.
Insert
axle from
outside
Left
Insert
axle from
outside
Figure 5
Right
7. To operate the brakes on the wheels, press downward on the brake
lever as shown in figure 14. To release, lift upward on the lever.
Playard assembly is now complete and ready to use.
Outside
Inside
Figure 6
Figure 7
Figure 11
Figure 8
Figure 12
Figure 9
Figure 13
Figure 10
Figure 14
4
FOLDING PLAYARD
1. Undo the 6 hook and loop straps holding mattress from underneath
Playard floor. (If mattress is not used in the bassinet). Remove mattress
and set aside.
2. Grasp the center floor lock handle pushing down. Rotate the handle
counter-clockwise about 90 degrees and lift upward until handle is as
high as the top rails. Gather the four feet of the playard together so that
they nearly touch each other. See figures 1 and 2.
Rotate before
lifting
Figure 1
NOTE: TOP RAILS OF THE PLAYARD ARE STILL IN THE
“LOCKED” POSITION.
3. Locate release button on the center of the bottom of each top rail. Lift
slightly while squeezing button until the rail clicks. Push down on rail
(while still holding release button in) until side forms a “U”. Repeat for
remaining sides (Fig. 3).
NOTE: If top rail(s) do not form the “U” completely do not force. Check
the floor of your Playard to make sure all bottom rails are unlocked and
pull up on middle handle of floor again. Repeat step 3.
Figure 2
4. Pull up on handle in center of Playard (Fig. 4). Gather legs of Playard
together.
5. Wrap mattress around Playard frame with padded side facing in.
6. Secure the 3 hook and loop straps by feeding through loops on end of
mattress and folding back onto itself (Fig. 5).
7. Place Playard in carry bag so wheels come through opening in the end
of bag.
Figure 3
WARNING: NEVER LEAVE INFANT IN
PRODUCT WITH SIDES DOWN. Infant may
roll into space between pad and loose
mesh side causing suffocation.
Figure 4
Figure 5
5
PLAYARD BASSINET/CHANGING AREA
WARNING:FAILURE TO FOLLOW THESE WARNINGS AND THE
ASSEMBLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR
DEATH FROM ENTRAPMENT, STRANGULATION, SUFFOCATION, ETC.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep, unless
otherwise advised by your physician.
• Always provide the supervision necessary for the continued safety of your child. When used for playing,
never leave child unattended.
• Adult supervision is always necessary when using your bassinet.
• Your playard, including side rails and bottom pad, must be fully erected prior to use.
• Top rails must be locked.
• Bottom rails must be in flat, locked position.
• SUFFOCATION HAZARD: To help prevent suffocation from entrapment, use only the mattress provided
by Baby Trend®. Never use additional mattress or padding. Never use plastic shipping bags or other plastic
film as mattress covers not sold and intended for that purpose. Avoid SUFFOCATION HAZARD caused by
a loose sheet. A fitted sheet is recommended. The fitted sheet must fit the mattress tightly.
• STRANGULATION HAZARD: DO NOT place items with a string around child’s neck, such as hood
strings or pacifier cords. DO NOT suspend string over bassinet or attach strings to toys.
• DO NOT add padding or other objects inside your bassinet which will permit a child to climb out.
• To prevent your child from falling out of the bassinet discontinue using your bassinet when
your child is too active, able to climb out, weighs over 15 lbs.. (6.8 kgs.), or is over 4 months old.
• Use changer with infant who’s weight is less than 18 lbs (8.2 kg ) and is less than 25 inches (63.5 cm) tall.
• Discontinue use of changer if infant can push up on hands and knees or sit unassisted.
• DO NOT use a water mattress with this bassinet.
• Use your bassinet with only one child at a time.
• Keep bassinet away from stoves, heaters, campfires and other hazards.
• Never place a child under the bassinet.
• Never leave changer on top of playard with a child in the playard. Always flip changer to the outside
when not in use.
• DO NOT store the bassinet in the playard.
• The bassinet must be fully assembled and installed, including top rails and bottom pad, before using.
• Before each use or assembly, inspect the playard and bassinet / changing area for damaged hardware,
loose joints, missing parts or sharp edges. DO NOT use playard or bassinet if any parts are missing or
broken. Call our Customer Service department at (800) 328-7363 for replacement parts.
• To protect your child from falls and other injuries: always use safety belt when child is on the changing
table, always stay within arm’s reach of your child when using the changing table, never leave child
unattended.
Baby Trend, Inc.
1567 S. Campus Ave.
Ontario, CA 91761
Customer Service Hot Line:
(800) 328-7363
8:00 A.M. to 4:30 P.M. Pacific Standard Time
6
TO ASSEMBLE YOUR BASSINET
NOTE: Playard MUST be in a locked set-up position before
installing and using the bassinet feature.
CONTENTS (Fig. 1):
1 Nylon bassinet insert
4 Metal support tubes 2 (male) (2 female)
ASSEMBLY
1. Insert the 2 female tubes into the two male tubes. (Fig. 2)
2. Insert the 2 assembled tubes through the loops provided on the
bassinet insert. (Fig. 3).
3. Place assembled bassinet onto the Playard. Push down each of the
bassinet supports onto the playard frame as shown in (Fig. 4).
Figure 1
NOTE: The printed warning label should be facing toward the
inside of the bassinet so that it is readable.
4. Place the Playard mattress into the bassinet with the padded side
facing up (Fig. 5).
Figure 2
Figure 3.
Figure 5.
Figure 4.
7
TO ASSEMBLE CHANGING AREA
CONTENTS (Fig. 1):
•
•
•
2 Long curved bars
2 Short bars with connector knobs
1 Changing area fabric
WARNING:
•
•
•
•
•
Figure 1
Avoid serious injury or death:
Always use restraint belt to prevent falls
Use changer with infant who’s weight is less
than 18 lbs (8.2 kg ) and is less than
25 inches (63.5 cm) tall.
Discontinue use of changer if infant can push
up on hands and knees or sit unassisted.
DO NOT carry changer with infant in it.
Always stay within arms reach of your child
when using the changing area.
Figure 2
WARNING:
Strangulation Hazard
Child can lift the changing table and get
neck trapped between the changing table
frame and the play yard frame. Never leave
the changing table in place when the child is
in the bassinet or the play yard. Always flip
changer to the outside when not in use.
Holes face
down
Figure 3
ASSEMBLY
1. Connect the two Long Curved Bars together as shown in figure 2.
2. Insert the assembled Curved Bars into the Changing Area Fabric
such that the holes in the ends of the Curved Bars face downward
as shown in Figure 3.
3. Slide the Curved Bars around inside the sleeve of the Changing
Area Fabric.
4. Connect the Short Bars with Connector Knobs to the Curved
Bars as shown in figure 4. When assembling the Short Bars with
Connector Knobs make sure that the knobs will be facing inward
when assembled and the snap buttons are facing downward.
Figure 4.
Completed assembly
Figure 5.
8
NOTE: Short bar with connector knobs should be facing
inward.
5. Place connector knob prongs into holes located on corner pieces
of Playard (Fig. 5).
6. Turn connector knobs counter clockwise to lock (Fig. 6).
7. Flip changing area to inside of Playard (Fig.7).
8. Snap flap from changing area to side of Playard (Fig. 8).
9 Check that changing area is secure before using.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
REMOVAL AND FOLDING CHANGING AREA
REMOVAL
1. Flip changing area to the outside of the Playard. Unsnap fabric flap
of changing area from Playard.
2. Twist connector knobs clockwise to unlock (Fig. 1).
3. Remove changing area from Playard (Fig. 2).
4. Disconnect the short bars from the curved bar by pressing on the
snap buttons and pulling apart. Remove curved bar from changing
area sleeve.
Figure 1.
The changing area is now ready for storage.
Figure 2.
9
HOW TO USE CHANGING TABLE RESTRAINT
1. Place child on changing table, make sure hands and arms are clear of the restraint.
Bring the restraint around the child's waist and clip the male and female ends of the
buckle together. See Fig 1
2. Tighten strap until fits snug around child's waist. DO NOT OVER TIGHTEN. See Fig. 2
3. To remove un snap the buckle.
Fig. 1
Fig. 2
DO NOT USE CHANGING TABLE IF IT IS DAMAGED OR BROKEN
10
REMOVAL OF BASSINET
REMOVAL
1. Remove mattress from bassinet (Fig.1).
2. Lift bassinet out of Playard (Fig. 2).
The bassinet is now ready for storage.
NOTE: Store bassinet and changing area with folded Play yard
in carry bag.
Figure 1
Figure 2
TO INSTALL TOY BAR
1.
Attach the toy bar to each end of the playard opposite of the
changing table. Clip the plastic hooks onto the top rails of the
play yard. (Fig. 3.)
WARNING:
This toy bar is designed
to be used from birth to 5 months. A toy bar is intended for visual stimulation and is not intended
to be touched by the child. Possible entanglement
injury: keep out of the baby’s reach. Do Not place
your baby directly under the toy bar. Remove toy
bar from playard when baby begins to push up on
hands and knees.
Figure 3.
IF YOU EXPERIENCE ANY DIFFICULTY IN USING THIS PRODUCT, PLEASE
CONTACT OUR CUSTOMER SERVICE DEPARTMENT AT (800) 328-7363 BETWEEN
THE HOURS OF 8:00 A.M. AND 4:30 P.M. PACIFIC COAST TIME FOR ASSISTANCE.
11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement