AEG | Voxtel D200 | User guide | AEG Voxtel D200 User guide

AEG Voxtel D200 User guide
1
UK
CORDLESS
TELEPHONE
Voxtel D200/D205
V1
UK
USER GUIDE
2
P1
P2
1
OK
8
7
6
2
P3
3
1
2 ABC 3 DEF
4 GHI 5 JKL 6MNO
7 PQRS 8 TUV 9WXYZ
0
5
P4
R
4
P5
16
9
10
11
12
13
15 14
3
BECAUSE WE CARE
Thank you for purchasing this product. This product has been designed
and assembled with utmost care for you and the environment. This is
why we supply this product with a quick installation guide to reduce the
number of paper (pages) and therefor save trees to be cut for making this
paper.
A full and detailed user guide with all the features descripted can be
found on our website www.aegtelephones.eu . Please download the full
user guide in case you want to make use of all the advanced features of
your product. To save the environment we ask you not to print this full user
guide. Thank you for supporting us to protect our environment.
2
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone, basic safety precautions should always be
followed to reduce the risk of fire, electric shock and injury, including the
following:
1. Read and understand all the instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug the power adapter from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
4. Keep your phone away from hot, humid conditions or strong sunlight
and don’t let it get wet or use this product near water (for example,
near a bath tub , kitchen sink, swimming pool).
5. Do not overload wall outlets and extension cords as this can result in
the risk of fire or electric shock.
6. Unplug this product from the wall outlet under the following conditions:
tWhen the power supply cord or plug is damaged.
tIf the product does not operate normally by following the operating
instructions.
tIf the product has been dropped and the cabinet has been damaged.
tIf the product exhibits a distinct change in performance.
7. NEVER use your phone outdoors during a thunderstorm-unplug the
base from the telephone line and the mains socket when there are
storms in your area. Damage caused by lightning is not covered by
the guarantee.
8. Do not use the telephone to report a gas leak in the vicinity of the leak.
9. Use only the supplied NiMH (Nickel Metal Hydride) batteries!
UK
1
4
10. The use of other battery types or non-rechargeable batteries/primary
cells can be dangerous. These may cause interference and/or damage
to the unit or surroundings. The manufacturer will not be held liable for
damage arising from such non-compliance.
11. Do not use third party charging bays. Damage may be caused to the
batteries.
12. Please ensure the batteries are inserted in the correct polarity.
13. Dispose of batteries safely. Do not immerse them in water, burn them,
or put them where they could get punctured.
3
INTENDED USE
This telephone is intended to be connected to a public analogue
telephone network or to an analogue extension of an approved
compatible PBX system.
4
UNPACKING YOUR PHONE
In the box you will find:
t1 Handset
t1 Base station
t1 Mains power adapter
t1 Telephone line cord
t2 Rechargeable batteries
t1 User manual
Keep the packing materials in a safe place in case you later need to
transport the device.
5
GETTING TO KNOW YOUR PHONE
5.1
Handset overview (see P1)
UK
5
#
Meaning
1
Up key
tIn idle mode: press to access the call list
tIn menu mode: press to scroll up the menu items
tIn phonebook list / redial list / call list: press to scroll up
the list
tDuring a call: press to increase the earpiece volume
tDuring ringing: press to increase the ringer volume
2
Right soft key (clear/back/mute/intercom)
tIn main menu mode: press to go back to idle screen
tIn sub-menu mode: press to go back to previous level
tIn sub-menu mode: press and hold to go back to idle
screen
tIn editing / predialling mode: press to clear a character/
digit
tIn editing / predialling mode: press and hold to delete all
the characters / digits
tDuring a call: press to mute / unmute the microphone
tIn idle mode: press to intercom another handset
3
Off / hang up key
tDuring a call: press to end a call and go back to idle screen
tIn menu / editing mode: press to go back to previous
menu
tIn idle mode: press and hold to power off the handset
tIn idle mode (when the handset is powered off): press and
hold to power on the handset
4
Recall/flash key
tIn idle / predialling mode: press to insert a recall / flash
tDuring a call: press to generate flash / recall signal
R
6
5
Speakerphone key
tDuring a call: press to turn on / off the speakerphone.
tCall list / phonebook entry: press to make a call with
speakerphone
tDuring ringing: press to answer a call with speakerphone
6
Down key (redial/down)
tIn idle mode: press to access the redial list
tIn menu mode: press to scroll down the menu items
tIn phonebook list / redial list / call list: press to scroll down
the list
tDuring a call: press to decrease the earpiece volume
tDuring ringing: press to decrease the ringer volume
7
Talk key
tIn idle / predialling mode: press to make a call
tIn redial list / call list / phonebook list: press to make a call
to the displayed entry
tDuring ringing: Press to answer a call
8
Left soft key (menu/ok)
tIn idle mode: press to access the main menu
tIn sub-menu mode: press to confirm the selection
tDuring a call: press to access Intercom/phonebook/ redial
list/ call list
OK
5.2
Display icons and symbols (see P2)
The LCD display gives you information on the current status of the
telephone.
Meaning
Steady when the handset is in range of the base.
Flashes when out of range of the base or not registered to
the base.
Steady when an intercom call is in progress.
Flashes when there is an incoming internal call.
Indicates a call is in progress on that handset.
7
Indicates that your answering machine (TAM) is on and flashes
when there is a new message.
Indicates that the handset ringer is switched off.
Steady when an alarm is set.
Flashes when the alarm is sounding.
Indicates that the keypad is locked.
Indicates when you have a new Voice Mail message.
(This is a caller display service from the network operator.)
Indicates when the battery is fully charged.
Whole icon flashes when the battery is charging.
Internal block icon flashes when the battery is in final charging
stage.
Indicates when the battery needs charging.
Flashes when low battery power level is detected.
Indicates when there are more characters or numbers in front
of those
being displayed.
Indicates when there are more characters or numbers after
those being
displayed.
Left soft key function. Press to access the main menu.
Left soft key function. Press to confirm the current selection.
Indicates new TAM message / new call in TAM message list
/ call list.
Indicates more options available in lists, above or below.
Right soft key function. Press to start an intercom call.
UK
Indicates that speakerphone is being used.
8
Right soft key function. Press to go back to the previous menu
(back) level or cancel the current action.
Right soft key function. Press the alarm, or mute/unmute the
microphone during a call.
5.3
Base station with telephone answering machine (TAM) control
(see P4)
#
Meaning
9
Delete
Press once to delete the message during playback.
In idle mode, press and hold to delete all the old
messages.
10
Skip forward
Press to skip the current message and play the next
message.
11
Play/stop
Press to play messages.
Press to stop the message playback.
12
Press to increase the playback volume.
13
Press to decrease the playback volume.
14
Find
Press to page your registered handset(s).
Press and hold to start the registration process.
15
TAM on/off
Press to turn on the answering machine.
Press again to turn off the answering machine.
16
Skip backward
Press to repeat playing the current message from the
beginning.
Press twice to skip back to the previous message.
9
Base two digit-LED display information
0F-> -0n-> XX
Displayed when the answering machine is turned off.
Displayed when the answering machine is turned on where
XX is number of messages in TAM memory.
00
Steady on: no voice messages in the TAM.
XX
Flashing: there are XX new messages recorded where XX
is from 01 to 59.
ZZ
Steady on: there are ZZ old messages in the TAM memory
and no new messages.
XX/FF
Flashing XX alternately with FF: there are XX new voice
messages recorded and the TAM memory is full.
FF
Flashing FF: the TAM memory is full and there are no new
messages.
- - /XX
Flashing XX alternately with - -: the time / date is not set
and there are XX new messages recorded.
--
Flashing - -: the time / date is not set and there are no new
messages recorded.
XX
XX steady on: playing the current XX old recorded
message.
XX flashing: playing the current XX new recorded incoming
message.
A1/A2
Steady on: playing the current outgoing message (OGM)
where A1 is the answer & record OGM and A2 is the
answer only OGM.
XX/An
Flashing XX alternately with An: currently recording the
new XX incoming message.
rA
Flashing: remote access is in progress from a handset or
via the external line.
LX
Steady on: indicates the current volume level where X is
from 1 to 8.
UK
5.4
10
5.5
Menu structure
tIn idle mode, press to go to CALL LIST, the first option in the menu
list.
tPress / to go to other options in the menu list.
tPress OK to enter a sub-menu or function.
tPress to go back to the previous level
tRefer to the following for the menu structure.
/
Key press
Main Menu
Sub-menu
/
CALL LIST
PHONEBOOK
Shows
Shows
“EMPTY” or “EMPTY”
the first Call or the first
phonebook
List Entry.
Then
for: Entry.
Then
- ADD
for:
TO PB
- ADD PB
- DELETE
STATUS
- DELETE
or
ALL
- ADD
- DETAILS
- VIEW
- EDIT
- DELETE
- DELETE
ALL
- PB STATUS
/
BS
SETTINGS
- BS RINGER
- RING
VOLUME DELETE HS
- FLASH
TIME
- CHANGE
PIN
/
HS
SETTINGS
- ALARM
- RING
SETUP
- TONE
SETUP
- LANGUAGE
- RENAME
HS
- HS
DISPLAY
- AUTO
ANSWER
- DATE &
TIME
/
REGISTRATION
PIN? ----
/
DEFAULT
PIN? ----
/
ANS.
MACHINE
- MSG
PLAYBACK
- DELETE
ALL
MEMO
- TAM ON/
OFF
- TAM
SETTINGS
- ANSWER
MODE
- TAM LANGUAGE
- OGM
SETTINGS
- ANSWER
DELAY
- RECORD
TIME
- REMOTE
ACC
- COMPRESSION
- BS
SCREENING
- CHANGE
PIN
5.6
Text and Digit Entry
The following tables show you where each letter and punctuation
character can be found, by using repeated presses of the alphanumeric
keypad. This will be helpful when storing a name in the phonebook and
renaming your handset.
In editing mode, a cursor is displayed to indicate the current text entry
position. It is positioned at the right of the last character entered.
Writing Tips:
tOnce a character is selected, the cursor will move to the next position
after a short pause.
tYou can move the cursor within the text with the / keys to amend
the text entry.
tPress to delete the last character.
tPress and hold to delete the entire text string.
5.6.1
Key
Key Press
1
2
3
4
5
6
7
8
9
0
*
#
6
English Character Set
Alphanumeric Editing
(For phonebook name editing and renaming handset)
1st
space
A
D
G
J
M
P
T
W
0
*
°
2nd
B
E
H
K
N
Q
U
X
3rd
1
C
F
I
L
O
R
V
Y
4th
?
‘
/
,
\
-
2
3
4
5
6
S
8
Z
5th
6th
7
9
(
&
)
7th
8th
Number Editing (For
phone number editing,
date/time editing)
9th
10th
1
2
3
4
5
6
7
8
9
0, or P (if press and hold)
*
INSTALLATION
6.1
Connecting the base station (see p5)
tPlug the power supply and line cord into the base station.
tPlug the power adapter into a 230 V ac/50Hz mains socket and the line
cord into your telephone line socket.
Warning:
Use only the provided adaptor, using other power supplies may cause a
hazard or damage the phone.
Install the base unit in a position where the mains adapter plug will reach
an easily accessible mains socket to unplug in case needed. Never try to
lengthen the mains power cable.
UK
11
12
Note:
The base unit needs mains power for normal operation, not just for
charging the handset batteries.
6.2
Installing and charging the batteries (see P3)
tPlace the 2 supplied batteries into the battery compartment with
the polarity markings. Use only the NiMH rechargeable battery type
provided with the telephone.
tPosition the battery compartment cover over the batteries and slide up
to click into place.
tPut the handset on the base and charge for 15 hours before using the
handset for the first time.
>The handset will give a beep when it is properly placed on the base
or charger.
7
TELEPHONE OPERATION
7.1
Make a call
7.1.1 Preparatory dialling
tEnter the phone number and press to connect to the line and dial the
number.
>When entering the number, if you make a mistake, press to delete
digits.
7.1.2 Direct dialling
tPress to connect to the line and then enter the phone number.
7.1.3 Call from the phonebook
tPress , , OK to access the phonebook and press
desired phonebook entry.
tPress to dial out the selected phonebook entry.
/
to select the
Note:
The alphanumeric keys provide a short-cut to find entries beginning with
the corresponding letters.
7.1.4 Call from the call list (only available with caller display)
to access the call list and press / to select the desired call
tPress
list entry.
13
to dial out the selected call list entry.
7.1.5 Call from the redial list
to access the redial list and press /
tPress
redial number.
tPress to dial out the selected redial number.
to select the desired
7.1.6 Call timer
Your handset automatically times the duration of every call.
The call timer is displayed as soon as you answer a call or 15 seconds after
dialling and remains on the screen for 5 seconds after the end of the call.
It is shown in hours, minutes and seconds format (HH:MM:SS).
7.2
Answer a call
If the handset is not on the charging cradle:
tWhen the phone rings, press to answer a call.
Note:
If “AUTO ANSWER” is set to “ON”, then lifting the handset off the base or
charger will answer the call automatically and no keys need to be pressed.
7.3
End a call
to end the call.
tDuring a call press
OR
tPut the handset on the base station or charger to end the call.
7.4
Handset speakerphone
to alternate between hands-free
During a call, you can press
speakerphone and normal handset use.
7.5
Adjust volume
There are 5 levels (“VOLUME 1” to “VOLUME 5”) to choose from for each
of the earpiece and speaker volumes.
During a call:
tPress / to select volume 1-5. The current setting is shown.
>When you end the call, the setting will remain at the last selected
level.
7.6
Mute a call
You can talk to someone nearby without letting the caller hear you during
a call.
UK
tPress
14
During a call:
) to mute the microphone and “MUTED” will display on
Press “C” (
the LCD.
) again to unmute the
Your caller cannot hear you. Press “C” (
microphone.
7.7
Turn off the handset ringer
In idle, press and hold # to turn off the handset ringer. The
displayed on the LCD.
icon is
Note:
and show “CALL” or the caller
The display will still flash the call icon
display number, when there is an incoming call, even if the ringer is turned
off.
To turn the ringer back on, press and hold # again.
7.8
Turn on the keypad lock
You can lock the keypad so that it cannot be used accidentally while
carrying it around.
icon will
tIn idle, press and hold * to turn on the keypad lock and the
display.
Note:
You can still use to answer a call when the handset is ringing.
To turn the keypad lock off, press and hold * again.
7.9
Redial the last number
You can redial any of the 5 last numbers called. If you have stored a name
in phonebook to go with the number, the name will be displayed instead.
The most recent last number will display at the top of the redial list.
7.9.1 Redial a number from the redial list
to access the redial list.
tIn idle mode, press
Note:
If the redial list entry shows a name, press # to view the number of this
entry.
tPress / to browse the redial list.
tPress to dial to the selected redial number.
Note:
If there are no numbers in the redial list, the display shows “EMPTY ”.
7.9.2 Store a redial number into the phonebook
tFollow Steps 1 and 2 in section 7.9.1.
tPress OK and / to select “ADD TO PB“.
tPress OK and then enter the name you want to use in the phonebook.
tPress OK and then modify the number, if necessary.
tPress OK to show “MELODY 1“.
tPress / to browse the ringtone list. The respective ringtone will be
played when browsing the ringtone list.
Note
The selected melody will only be played when you receive a call if you
subscribe to Caller Display and the incoming number matches the stored
number.
tPress OK to confirm, and the entry will be stored.
7.9.3 Delete a redial number
tFollow Steps 1 and 2 in section 7.9.1.
tPress OK and / to select “DELETE“.
tPress OK to confirm, and the entry will be deleted.
7.9.4 Delete all redial list entries
tFollow Steps 1 and 2 in section 7.9.1.
tPress OK and / to select “DELETE ALL“.
tPress OK to display “CONFIRM?“.
tPress OK to confirm. All entries will be deleted and the display will show
“EMPTY“.
7.10
Find the handset
You can locate the handset by pressing the find key 14 . All the handsets
registered to the base will produce the paging tone and show “PAGING“
on the display for 60 seconds.
on any handset or
on the
You can stop the paging by pressing
base again.
Note:
If there is an incoming call during paging, the phone will ring with the
incoming call instead of paging.
UK
15
16
7.11
Make an Internal Call (Multi - handset versions only)
This feature is only applicable when there are at least two registered
handsets. It allows you to make internal calls, transfer external calls from
one handset to another handset and make conference calls. If the called
handset is not answered within 60 seconds, the called handset will stop
ringing and the calling handset will return to standby mode.
Note:
If only one handset is registered to the base station, when
it will display “NOT POSSIBLE”.
is pressed,
7.11.1 Intercom another handset
) and all the other registered handset
tIn idle mode, press “C” (
numbers will display, along with a “9“.
tEnter the number of the handset that you want to call or enter “9“ to
call all handsets.
tThe called handset rings and must be pressed on that handset to
establish the intercom call.
Note:
If only two handsets are registered to the base station, pressing “C” (
will call the other handset immediately.
)
Note:
If there is an external call while you are on an intercom call, you‘ll hear
warning beeps, and you have to end the intercom call, before you can
answer the external call.
7.11.2 Call all handsets
and the registered handsets will display.
tIn idle mode, press
tPress the “9“ key to ring to all registered handsets.
7.11.3 Transfer an external call to another handset
During an external call:
tPress to select “INTERCOM“.
tPress OK to show all the other registered handset numbers, plus “9”.
Enter the number for the handset you want to transfer the call to.
tThe external call is put on hold automatically and the called handset
rings.
tPress on the called handset to establish an internal call.
tPress
on the calling handset or put the calling handset on the
charging cradle to end the current call with the external party.
tThe external call is transferred to the called handset.
Note:
If the other handset has not answered the intercom call, you can stop the
intercom and return to the external call by pressing .
7.11.4 Make a 3-way conference call
The conference call feature allows one external call to be shared with two
handsets (in intercom).
The three parties can share the conversation and no additional network
subscription is required.
During an external call:
tFollow Steps 1 to 4 in section 7.11.3.
tPress and hold the star key * on the calling handset to establish the
conference call.
Either handset can exit the conference by pressing , leaving the other
handset still connected to the external call.
8
PRIVATE PHONEBOOK
Each handset can store up to 50 private phonebook entries with names
and numbers. Each phonebook entry can have a maximum of 20
digits for the phone number and 12 characters for the name. You can
also select different ringtones for your phonebook entries. (Note: the
different ringtones only play when you receive a call if you subscribe to
caller display and the incoming number matches the stored number.)
Phonebook entries are stored alphabetically by name.
8.1
Add a new phonebook entry
In idle:
and
/
to select “PHONEBOOK” and then press OK to
tPress
access the phonebook.
tPress OK to show “ADD”.
tPress OK and then enter the name.
tPress OK and then enter the number.
tPress OK and / to select the desired ringtone for your phonebook
entry.
UK
17
18
tPress OK to store the phonebook entry.
8.2
Search for a phonebook entry
In idle:
and
/
to select “PHONEBOOK” and then press OK to
tPress
access the phonebook.
tEnter the first letter of the name using the alphanumeric keys (e.g. if it
begins with C, press the 2 key three times) and then / to scroll to
the entry you want.
8.3
View a Phonebook Entry
In idle:
and
/
to select “PHONEBOOK“ and then press OK to
tPress
access the phonebook.
tPress / to select the desired phonebook entry.
tPress OK and / to select “VIEW“.
tPress OK and / to review the name, number and ringtone of the
selected phonebook entry.
Note:
If the number is more than 12 digits, press
remaining digits.
OK or
to view the
8.4
Edit a phonebook entry
In idle:
and
/
to select “PHONEBOOK and then press
tPress
access the phonebook.
tPress / to select the desired phonebook entry.
tPress OK and / to select “EDIT”.
tPress OK to display the current name.
tEdit the name and press OK.
tEdit the number and press OK.
tPress / to select the ringtone and press OK to confirm.
8.5
Delete a phonebook entry
In idle:
and
/
to select “PHONEBOOK” and then press
tPress
access the phonebook.
tPress / to select the desired phonebook entry.
tPress OK and / to select “DELETE”.
OK to
OK to
19
8.6
Delete all Phonebook entries
tPress
and
/
to select “PHONEBOOK“ and then press OK to
access the phonebook.
tPress OK and / to select “DELETE ALL“.
tPress OK to display “CONFIRM?“.
tPress OK to confirm. All entries will be deleted and the display will show
“EMPTY“.
8.7
Check the Phonebook Usage
You can check how many phonebook entries are stored in your handset
and how many phonebook entries are available for you to store in the
phonebook.
and
/
to select “PHONEBOOK“ and then press OK to
tPress
access the phonebook.
tPress OK and / to select “PB STATUS“.
tPress OK to display how much of the phonebook is being used, for
example “14/20 USED“ means 14 entries are stored out of the total 20
available spaces.
9
CALLER DISPLAY (NETWORK DEPENDENT)
This feature is available if you have subscribed to the calling Line
Identification service with your network service provider. Your phone can
store up to 20 received calls with date/time information in the call list. The
number will be shown on the handset display when the phone is ringing.
If the number matches with one of the entries in your private phonebook,
the caller‘s name stored in the private phonebook will be displayed
alternately with the number, and the handset will ring with the ringtone
associated with that phonebook entry.
If the call is from someone who withheld their number, “WITHHELD” will
display.
If the call is from someone whose number is unavailable, e.g. an
international call or from a private exchange, “OUT OF AREA” will display.
If you‘ve got new caller display records, the handset will display “X NEW
CALLS“ in standby mode. The New calls indication will remain until all the
new call records have been viewed on that handset.
UK
tPress OK to confirm, and the entry will be deleted.
20
9.1
View the call list
All received calls are saved in the call list with the latest call at the top of
the list. When the call list is full, the oldest call will be replaced by a new
call. Any unanswered calls which have not been viewed are marked with a
icon at the centre of the bottom line of the display.
to access the call list.
tPress
OR Press and / to show “CALL LIST”, then press OK.
tPress / to select the desired entry.
tPress # to view the caller’s number if applicable.
/
to show “DETAILS”, and then OK to display the date
tPress ,
and time of the call.
tPress OK to go back to the previous screen.
9.2
Store a call list number into the phonebook
tFollow Steps 1 and 2 in Section 9.1.
tPress OK and / to show “ADD TO PB“.
tPress OK and then enter the name.
tPress OK and the selected call list number is displayed.
tEdit the number if necessary.
tPress OK and / to select the ringtone.
tPress OK to store the phonebook entry and return to the calls list.
9.3
Delete an entry in the call list
tFollow steps 1 and 2 in section “9.1 View the call list” on page 20.
tPress and / to select “DELETE”.
tPress OK to confirm.
9.4
Delete all call list entries
Follow steps 1 and 2 in section “9.1 View the call list” on page 20.
tPress and / to select “DELETE ALL”.
tPress OK to display “CONFIRM?”.
tPress OK to confirm.
>All entries will be deleted and the display will show “EMPTY”.
21
PHONE SETTINGS
Your phone comes with a selection of settings that you can change to
personalise your phone the way you like it to work.
10.1
Date and Time Settings
If you subscribe to Caller Display the time and date settings will be
automatically updated by the network when you receive an incoming call.
The Caller Display service only sends the month and date, not the year, so
you may need to set the year.
10.1.1 Change the Date Format
tPress and / to select “HS SETTINGS“.
tPress OK and / to select “DATE & TIME“.
tPress OK and / to select “DATE FORMAT“.
tPress OK and / to select your desired date format (DD-MM-YYor
MM-DD-YY ).
tPress OK to confirm.
10.1.2 Change the Time Format
tPress and / to select “HS SETTINGS“.
tPress OK and / to select “DATE & TIME“.
tPress OK and / to select “TIME FORMAT“.
tPress OK and / to select your desired time format (12 HR or 24 HR).
tPress OK to confirm.
10.1.3 Set the Time
tPress and / to select “HS SETTINGS“.
tPress OK and / to select “DATE & TIME“.
tPress OK and / to select “SET TIME“.
tPress OK and then enter the time information in 24 hour format.
tPress OK to confirm.
Note:
If time has been set before, the current time will display, otherwise,
“HH:MM” will display.
10.1.4 Set the Date
tPress and / to select “HS SETTINGS“.
tPress OK and / to select “DATE & TIME“.
tPress OK and / to select “SET DATE“.
UK
10
22
tPress OK and then enter the date information in the format you set in
Section 10.1.1.
tPress OK to confirm.
Note:
If date has been set before, the current date will display, otherwise, “DDMM-YY ” will display.
10.2
Alarm Settings
You can set an alarm time on this phone. When an alarm is set, the alarm
is shown on the handset display. When the alarm time is reached,
icon
and “ALARM ON“ flash on the handset display, and
the alarm icon
the alarm tone rings for 45 seconds. You can press any key to disable the
alarm.
If the snooze function is activated,the alarm will sound again at the end of
the snooze period of seven minutes. You can also press and hold while
the alarm is sounding, to stop the alarm and turn off the snooze function.
Note:
>A key press will still disable the alarm even if the handset keypad is
locked when the alarm rings.
>The alarm volume level is the same as the settings of the handset
ringer volume. If the handset ringer is set to “VOLUME OFF“, the
alarm still sounds at VOLUME 1 level.
>During an external call or internal call, if an alarm is set and when
and “ALARM ON” will still flash.
the alarm time is reached, the
An alarm tone will be emitted from the earpiece to alert the user
the alarm time is reached. Once the user presses any key or presses
to disable the alarm, the display will revert to the call
and holds
duration.
>During paging or ringing, the alarm will not sound when the alarm
time is reached. However, if the snooze function is enabled and there
is no paging or ringing, the alarm will sound again at the end of the
snooze period.
10.2.1 Turn on/off the Alarm
tPress and / to select “HS SETTINGS“.
tPress OK to show “ALARM“.
tPress OK and / to select “ON“/“OFF“.
tPress OK to confirm.
Note:
If ON is selected, you will be prompted to set the alarm time.
10.2.2 Set the Alarm Time (If Alarm time is set to be “ON“)
tFollow Steps 1 to 4 in Section 10.2.1.
tEnter the alarm time in 24 hour format.
tPress OK to display “SNOOZE“.
tPress OK and / to select snooze “ON“ or “OFF“.
tPress OK to confirm.
10.3
Handset Settings
10.3.1 Set the Ringer Melody for Internal Calls
tPress and / to select “HS SETTINGS“.
tPress OK and / to select “RING SETUP“.
tPress OK to show “INT RING“.
tPress OK and / to select the melody you want to hear for internal
calls.
Note:
The respective melody will be played while browsing the ringtone list.
tPress OK to confirm.
10.3.2 Set the Ringer Melody for External Calls
tPress and / to select “HS SETTINGS“.
tPress OK and / to select “RING SETUP“.
tPress OK and / to select “EXT RING“.
/
to select melody you want to hear for external
tPress OK and
calls.
Note:
The respective melody will be played while browsing the ringtone list.
tPress OK to confirm.
10.3.3 Set the Ringer Volume
tPress and / to select “HS SETTINGS“.
tPress OK and / to select “RING SETUP“.
tPress OK and / to select “RING VOLUME“.
UK
23
24
tPress OK and
/
to select the desired ringer volume (a total of 6
ringer volume levels including “VOLUME OFF“).
Note:
ill b
The respective ringer volume w
will
be played during your selection. If
icon will be displayed.
“VOLUME OFF“ is selected, the
tPress OK to confirm.
10.3.4 Set Alert Tones
Three different alert tones are set on by default, but can be turned off, if
desired.
Key Tone - a single beep is emitted when you press a key.
Low Battery Tone - emitted while you are talking on the phone to alert
you that you need to charge the handset batteries.
Out of Range Tone - emitted while you are talking on the phone to alert
you to move closer to the base unit, before the call is lost.
tPress and / to select “HS SETTINGS“.
tPress OK and / to select “TONE SETUP“.
tPress OK and / to select “KEY TONE“ / “BATTERY TONE“ / “OUT
OF RANGE“.
tPress OK and / to turn on or off these tones.
tPress OK to confirm.
10.4
Set the handset language
tPress and / to select “HS SETTINGS”.
tPress OK and / to select “LANGUAGE”.
tPress OK and / to select the desired language.
tPress OK to confirm.
10.4.1 Rename the Handset
tPress and / to select “HS SETTINGS“.
tPress OK and / to select “RENAME HS“.
to delete
tPress OK and change the name of your handset, using
letters and the alphanumeric keys to enter up to 10 letters for the name.
tPress OK to confirm.
10.4.2 Choose the Information to be displayed in idle
You can choose to display time or handset name in your idle screen.
tPress and / to select “HS SETTINGS“.
tPress OK and / to select “HS DISPLAY“.
tPress OK and / to select “HANDSET NAME“ or “TIME“.
tPress OK to confirm.
Note:
If TIME is selected, but no time has been set the display will show --------.
10.5
Set the Auto Answer
If you turn on the Auto Answer, you can answer a call automatically by just
lifting the handset off the base or charger, without having to press any key.
tPress and / to select “HS SETTINGS“.
tPress OK and / to select “AUTO ANSWER“.
tPress OK and / to turn on or off the auto answer feature.
tPress OK to confirm.
10.6
Base Settings
10.6.1 Set the base ringer melody
tPress and / to select “BS SETTINGS”.
tPress OK and / to select “BS RINGER”.
/
to select the desired melody you want from a
tPress OK and
choice of 5.
tPress OK to confirm.
Note:
The respective ringer melody will be played while browsing the melody
list.
10.6.2 Set the ringer volume
tPress and / to select “BS SETTINGS”.
tPress OK and / to select “RING VOLUME”.
/
to select the desired ringer volume (a total of 6
tPress OK and
ringer volume levels including “VOLUME OFF”).
tPress OK to confirm.
Note:
The respective ringer volume will be played during your selection.
10.6.3 De-register a Handset
This operation should only be necessary if one of your handsets becomes
faulty or lost and needs to be replaced.
UK
25
26
You will need to enter the 4-digit System PIN (Default PIN is 0000) in order
to de-register a handset from the base station. A de-registered handset
will have the antenna icon flashing and “REGISTER” on the display.
Note:
You cannot de-register the handset that you are currently using.
tPress and / to select “BS SETTINGS“.
tPress OK to show “DELETE HS“.
tPress OK and the display shows “PIN? ------”.
tEnter the 4-digit system PIN (default 0000).
tPress OK and the first handset number is displayed.
tPress / to scroll through the list of registered handsets and select
the number of the handset you want to de-register.
tPress OK to confirm, and the chosen handset will be de-registered.
10.6.4 Change the Flash (Recall) Time
You may need to change the recall (flash) time if your phone is connected
to a PBX. The recall time options are “SHORT“ (the default value of
100ms), “MEDIUM“ (300ms) or “LONG“ (600ms).
tPress and / to select “BS SETTINGS“.
tPress OK and / to select “FLASH TIME“.
/
to select your desired flash time (“SHORT“,
tPress OK and
“MEDIUM“, “LONG“, with the current setting indicated by an asterisk
to the right).
tPress OK to confirm.
10.6.5 Change the System PIN Code
A 4-digit system PIN code is used for changing the system settings of the
base station. It is used to protect your phone against unauthorised use.
The default system PIN code is “0000“.
tPress and / to select “BS SETTINGS“.
tPress OK and / to select “CHANGE PIN“.
tPress OK and the display shows “PIN?------“
tEnter the old system PIN.
tPress OK to display “NEW PIN?------“, and enter your new 4-digit
system PIN.
tPress OK to display “CONFIRM?------“, and enter your new 4-digit
system PIN again.
Note:
If the new PIN entered in Step 6 is not the same as the new system PIN
entered in Step 5, you must enter the new system PIN at step 5 again.
tPress OK to confirm
10.7
Handset registration
Important:
When you purchase your phone, all handsets are already registered to
your base, so you do not need to register them.
Handset registration is only necessary when you buy extra handsets or if a
handset has become faulty.
You can register additional handsets to have up to five handsets per base
unit, with each handset‘s number (1 to 5) shown on its display. (Note: each
handset can only be registered to one base.)
To register a new handset to your base:
on the base station for more than five seconds, to
tPress and hold
put the base station into registration mode. It will stay in registration
mode for about 1 minute, so the following handset sequence must be
completed within this time.
tPress and / to select “REGISTRATION”.
tPress OK to display PIN?------.
tEnter the 4-digit system PIN (default 0000).
tPress OK to confirm, and the display will show “SEARCHING”.
If the handset registration is successful, you will hear a confirmation tone
will stop flashing.
and the
The handset will automatically be allocated the next available handset
number. This handset number is shown in the handset display in standby
will still flash.
mode. If the handset registration is unsuccessful, the
10.8
Reset your phone
You can reset your phone to the default settings. After a reset, all your
personal settings, call list entries, redial list entries, and answering machine
messages will be deleted but your phonebook remains unchanged:
tPress and / to select “DEFAULT“.
tPress OK to display “PIN?-----”.
UK
27
28
tEnter the 4-digit system “PIN“ (default 0000).
tPress OK to display “CONFIRM?“
tPress OK to confirm, and the phone will be reset to its default settings.
11
ANSWERING MACHINE (Only for D205)
Your phone includes a telephone answering machine that records
unanswered calls when it is on.The answering machine can store up to
59 messages within the maximum recording time of approximately 15
minutes. As well as recording incoming messages, you can record memos
for other users of your phone.
If the answering machine memory is full, the Handset will display “TAM
FULL” alternately with the handsets name or time, depending on the
handset standby display mode set. You will have to delete some messages
before any new ones can be recorded.
Some answering machine functions can be operated from the base,
including playing messages and turning the answering machine on or
off. The answering machine can also be controlled and set up using the
handset menu functions, as below.
11.1
Turn on/off the answering machine
You can turn the answering machine on or off using the handset.
When the answering machine is set to “ON”, calls will be answered after
the set answer delay and the caller can then leave you a message.
When the answering machine is set to “OFF”, calls will be answered after
14 rings and the answer only message will be played to your callers. They
will not be able to leave you a message.
tPress and / to select “ANS. MACHINE”.
tPress OK and / to select “TAM ON/OFF”.
tPress OK and / to select “ON” or “OFF”.
tPress OK to confirm.
displays on the handset LCD.
>If answering machine is set to “ON”,
will not display on the
>If answering machine is set to “OFF”,
handset LCD.
11.2
Listen to the messages in the answering machine
When new messages are recorded on the answering machine, the
flashes on the handset display until all the new messages are played. After
a new message is played it will be saved as an old message automatically
unless it is deleted.
Old messages will be played after all new messages are all played.
tPress and / to select “ANS. MACHINE”.
tPress OK and / to select “MSG PLAYBACK”.
tPress OK to start message playback through the earpiece and the
screen displays the date and time information of the message received.
Note:
is placed at the centre of the bottom of the handset display to
A
indicate that it is a new message.
will disappear and will not be
When a message has been played, the
shown when you listen to this message again.
Note:
If there are no messages, the handset display will briefly show “00-00 0000“ then return to “MSG PLAYBACK”.
or
to increase or decrease the
tDuring message playback, press
message playback volume respectively.
and
/
to select “STOP”, “FORWARD”, “PREVIOUS”,
tPress
“DELETE” to perform the following functions during message playback.
STOP
Stop the current message playback and return to the
ANS. MACHINE menu.
FORWARD
Skip to play the next message. The date and time
information of the next message will display if there is
another message.
PREVIOUS
Repeat playing the current message from the beginning.
The date and time information of the current message
will display.
DELETE
Delete the current message and the next message will
be played.
UK
29
30
Note:
Alternatively, you can use the following shortcut keys to control different
operations during message playback.
tPress key 5 to stop message playback.
tPress key 4 once to skip to repeat playing the current message from the
beginning. Press twice to skip backward to play the previous message.
tPress key 6 to skip to play next message.
tPress key 2 to delete the current message playback.
11.3
Delete all messages in the answering machine
tPress and / to select “ANS. MACHINE”.
tPress OK and / to select “DELETE ALL”.
tPress OK to display “CONFIRM?”.
tPress OK to delete all old messages.
Note:
If there are no more messages in the answering machine, “EMPTY” will
display and return back to “ANS. MACHINE” menu.
11.4
Record Memo
You can record a memo message for another user. When you record a
memo, the message counter will increase by one and the message can
be played back in the same way as answering machine messages. Memo
recording can still function even when the answering machine is turned
off.
tPress and / to select “ANS. MACHINE“.
tPress OK and / to select “MEMO“.
tPress OK to start memo recording and “RECORDING” is displayed.
tPress OK to stop memo recording and save the memo.
OR
to stop memo recording without saving and return back to the
tPress
“ANS. MACHINE“ menu.
11.5
Answering machine settings
You can use the “TAM SETTINGS” menu through the handset to change
the settings of your answering machine.
11.5.1 Set the answer mode
By default, the answer machine is set in “ANS & REC” mode which allows
callers to leave a message. This mode can be changed to “ANSWER
ONLY” which does not allow callers to leave a message. In that case, your
callers will be prompted to call back later.
tPress and / to select “ANS. MACHINE”.
tPress OK and / to select “TAM SETTINGS”.
tPress OK and / to select “ANSWER MODE”.
tPress OK and / to select “ANS & REC” or “ANSWER ONLY”.
tPress OK to confirm.
When your answering machine memory is full and it is in “ANS & RECORD”,
the answer mode will change to “ANSWER ONLY” automatically. It will
return to “ANS & RECORD” mode automatically after some messages
have been deleted.
11.5.2 Set the outgoing message (OGM) language.
The answering machine announces the outgoing message when it
answers a call. There is a pre-set OGM for each of “ANS & RECORD”
mode or “ANSWER ONLY” mode.
tPress and / to select “ANS. MACHINE”.
tPress OK and / to select “TAM SETTINGS”.
tPress OK and / to select “TAM LANGUAGE”.
tPress OK and / to select your desired OGM language.
tPress OK to confirm.
11.5.3 Record Your Own Outgoing Message (OGM)
You can record your own OGM for ANS & REC mode or ANSWER
ONLY mode. When you record your own OGM, it will be used when the
answering machine answers the call. If your personalised OGM is deleted,
the pre-set OGM will be restored automatically.
tPress and / to select “ANS. MACHINE”.
tPress OK and / to select “TAM SETTINGS”.
tPress OK and / to select “OGM SETTINGS”.
tPress OK and / to select “ANS & RECORD” or “ANSWER ONLY”.
tPress OK and / to select “RECORD MESS”.
tPress OK to start recording your personalised OGM and “RECORDING”
is displayed on the screen.
tPress OK to stop and save your personalised OGM.
>Your newly saved OGM will playback automatically.
to return to previous screen without saving the
tAlternatively, press
personalised OGM
UK
31
32
11.5.4 Playback and Delete the Outgoing Message (OGM)
You can playback your own personalised OGM or the pre-set OGM for
“ANS & REC“ mode or “ANSWER ONLY“ mode and choose to delete
your personalised OGM during playback and record a new one whenever
you want. Please note that pre-set OGM cannot be deleted.
11.5.4.1
Playback the OGM
tPress and / to select “ANS. MACHINE“.
tPress OK and / to select “TAM SETTINGS“.
tPress OK and / to select “OGM SETTINGS“.
tPress OK and / to select “ANS & REC“ or “ANSWER ONLY“.
tPress OK to show “PLAYBACK“.
tPress OK to playback your current OGM and “PLAYING OGM“ is
displayed on the screen.
tPress OK to stop the OGM playback and return to the previous menu.
Note:
If a personalised OGM has not been recorded, the pre-set OGM will be
played.
11.5.4.2
Delete the Personalised OGM
tRepeat Steps 1 to 6 in Section 11.5.4.1.
while the OGM is playing to delete your personalised OGM
tPress
and return to the previous menu and the pre-set OGM is restored
automatically.
Note:
If the pre-set OGM is playing, you are not allowed to delete it, so pressing
will just stop the playback and return to the previous menu.
11.5.5 Set the Answer Delay
You can set the number of rings before the answering machine answers
and starts playing your OGM. You can set the answering machine to
answer after two to eight rings or TIME SAVER. If Time Saver is set the
answering machine will answer after 5 rings if there are no new messages,
or after 2 rings if there is a new message, so if you call in and you don‘t
get an answer after 3 or 4 rings, you can hang up and save on call charges.
tPress and / to select “ANS. MACHINE“.
tPress OK and / to select “TAM SETTINGS“.
tPress OK and / to select “ANSWER DELAY“ (Available options: “2
RINGS“, “4 RINGS“, “6 RINGS“, “8 RINGS“ or “TIME SAVER“).
tPress OK and / to select your desired answer delay.
tPress OK to confirm.
11.5.6 Set the Recording Time of Incoming Message
You can set the maximum length of the recording time of the incoming
messages.
tPress and / to select “ANS. MACHINE“.
tPress OK and / to select “TAM SETTINGS“.
/
to select “RECORD TIME“ (Available options:
tPress OK and
“60S“, “120S“, “180S“ or “UNLIMITED“).
tPress OK and / to select your desired recording time.
tPress OK to confirm.
11.5.7 Call screening
When the answering machine is on and takes a call, you can listen to
the caller leaving a message. You can then identify the caller and decide
whether to take the call in person. The call can be screened at the base
and with any handset.
11.5.7.1
Screening at the base
By default, answering machine calls are played automatically through the
base speaker and the volume can be adjusted with the VOL + and VOL
-keys on the base.
If you don‘t want the caller to be heard when leaving a message, the base
screening can be turned off:
tPress and / to select “ANS. MACHINE“.
tPress OK and / to select “TAM SETTINGS“.
tPress OK and / to select “BS SCREENING“.
tPress OK and / to select “OFF“ or “ON“. (The current setting will
be indicated by a *.)
tPress OK to confirm the setting.
11.5.7.2
Screening with a handset
If the answering machine is set to ON, when there is an incoming message,
the handset will display “SCREENING?”
tPress to start call screening. Any Handset can listen to who is leaving
the message and decide whether to pick up the call or not.
tThe handset will display “SCREENING”.
tYou can adjust the earpiece volume by pressing / .
OR
UK
33
34
to return to previous screen and you cannot hear the
tPress
recording. At any time if you want to pick up the call, you can press and
the message recording will be stopped automatically. If the answering
machine is in the process of recording, the message already stored will
be saved.
11.5.8 Change the Compression Rate
Three different compression rates (“HIGH“, “MEDIUM“ and “LOW“) are
provided for you to select different quality levels of recording incoming
message. The lower the compression rate, the higher the recording
quality level attained, but the shorter the total recording time available.
(“LOW“ = 8 minutes, “MEDIUM“ = 11 minutes, “HIGH“ = 18 minutes
approx).
tPress and / to select “ANS. MACHINE“.
tPress OK and / to select “TAM SETTINGS“.
tPress OK and / to select “COMPRESSION“.
tPress OK and / to select your desired compression rate.
tPress OK to confirm.
11.5.9 Remote Access
Your phone lets you check your messages, or otherwise operate your
answering machine, by calling the answering machine when you are away
from home and then dialling a 4-digit remote access PIN from a tonedialling phone. The 4-digit remote access PIN code is used to prevent
other people from unauthorised access of your answering machine.
Note:
Remote Access must be turned on if you want to be able to use this
feature, see 11.5.9.2.
11.5.9.1
Change the 4-Digit Remote Access PIN
tPress and / to select “ANS. MACHINE“.
tPress OK and / to select “TAM SETTINGS“.
tPress OK and / to select “CHANGE PIN“.
tPress OK to show “PIN?----“, then enter the Old PIN. (Default Remote
Access PIN is 0000).
tPress OK to show “NEW PIN?----“, then enter your new 4-digit PIN.
tPress OK to show “CONFIRM?----“, then enter your new 4-digit PIN
again.
Note:
If the new PIN entered in Step 6 is not the same as the new PIN entered in
Step 5, you must enter the new system PIN at step 5 again.
tPress OK to reconfirm.
11.5.9.2
Activate or Deactivate the Remote Access
tPress and / to select “ANS. MACHINE“.
tPress OK and / to select “TAM SETTINGS“.
tPress OK and / to select “REMOTE ACC“.
tPress OK and / to select “ON“ or “OFF“ to turn the remote access
on or off respectively.
tPress OK to confirm.
11.5.9.3
Access Your Answering Machine Remotely
You can ring your phone from another tone-dialling phone to switch the
answering machine on or off, and/or listen to your messages remotely.
tPlace a call from a tone-dialling phone to your phone.
tWhen the answering machine answers the call and starts playing the
OGM, press the * key. The OGM will stop playing
tEnter the 4-digit Remote Access PIN (default PIN is 0000). You will hear
a single beep if the 4 digits are accepted, and then will need to press 5
to start playing any messages.
Note:
The * may be entered during or after the OGM, and the 4-digit PIN should
be follow without any delays.
Note:
If the 4-digit Remote Access PIN is not accepted, you will hear a multiple
beep, and if it is entered incorrectly three times consecutively, the line will
be released automatically.
tPress the following keys to carry out your desired function.
UK
35
36
Keys
2
4
5
6
7
8
9
Functions
While message is not playing
While message is playing
Delete the current message
playing
Repeat playing the current
message from the beginning.
Press twice to skip backward
to play the previous message
Play the message
Stop the current message
playback
Skip to play the next message
Turn on the answering machine
Stop the current message
palyback
Turn off the answering machine
Note:
If your answering machine is switched off, the phone will enter into the
remote access mode after 14 rings.
You can then enter the <*> key and the 4-digit remote access PIN (Default
Remote Access PIN is 0000) to activate the remote access feature.
37
TROUBLESHOOTING
Problem
Causes
Solutions
No dialling tone when
pressing
t The connection cord of
the base station is not
plugged in.
t The adapter cord is not
plugged in correctly in
the base station.
t Another handset is
using the base to make
a call.
t Wrong telephone line
cord.
the
t Check
connections. Unplug
and plug back in the
mains. Check that the
telephone cord has
been plugged into the
base station and the
phone socket.
t Check the base station
plug and the 230V plug
(remove and plug-in).
t Wait until the line is
unoccupied.
t Use
the
original
telephone line cord
supplied
When connect to a
PBX, no and/or wrong
connection after dialling.
Dialling prefix is needed.
Insert the dialling prefix.
“SEARCHING“
displayed.
tBase station out of Reduce the range.
Connect base station to
range.
tBase station not mains.
connected to mains.
is
The call does not work.
Service not activated or
wrong setting.
Check your Subscription
with the network.
No Display
Empty Battery
Recharge Battery
The answering machine
is turned off.
Turn on the answering
machine.
Answering Machine
The unit does not record
new messages.
UK
12
38
Problem
Causes
Solutions
The caller cannot leave a
message.
t The
answering
machine is turned off.
t Message memory is
full.
t ANSWER ONLY mode
is set.
t Turn on the answering
machine.
t Erase
unnecessary
messages.
t Change to ANS & REC
mode.
I cannot operate the
answering
machine
remotely.
t You are entering the
wrong remote access
code.
t You are pressing the
dial keys too quickly.
t You are using a pulse
telephone.
t If you forget the
remote access code,
reset to the default
settings.
t Press each key firmly.
t Try again using a touch
tone phone.
While
recording
an
outgoing message or
listening to messages,
the unit rings and
recording stops.
A call is being received.
Answer the incoming call
and try again to record
your outgoing message
later.
Please contact the technical support of the network provider for further
information.
This telephone is not equipped with a grounding function, and therefore
some of the functions may be limited when used in PBX systems.
39
GUARANTEE AND SERVICE
The phone is guaranteed for 24 months from the date of purchase shown
on your sales receipt. This guarantee does not cover any faults or defects
caused by accidents, misuse, fair wear and tear, neglect, faults on the
telephone line, lightning, tampering with the equipment, or any attempt
at adjustment or repair other than through approved agents.
Please keep your sales (till) receipt this is your proof of guarantee.
13.1
While the unit is under Guarantee
tDisconnect the base unit from the telephone line and the mains
electricity supply.
tPack up all parts of your phone system, using the original package.
tReturn the unit to the shop where you bought it, making sure you take
your sales receipt.
tRemember to include the mains adapter.
13.2
After the Guarantee has expired
If the unit is no longer under Guarantee, contact us via www.
aegtelephones.eu
This product works with rechargeable batteries only. If you put
nonrechargeable batteries in the handset and place it on the base, the
handset will be damaged and this in NOT covered under the warranty
conditions.
UK
13
40
14
TECHNICAL DETAILS
Standard
Digital Enhanced Cordless Telecommunication
(DECT)
Frequency range
1.88 to 1.9 GHz (bandwidth = 20 MHz)
Channel bandwidth
1.728 MHz
Operating range
Up to 300m outdoors; Up to 50m indoors
Operating time
Standby: 100 hours, Talking: 10 hours
Battery charge time:15 hours
Temperature range
Operating 0° C to 40° C,
Storage -20° C to 60° C
Electrical power
Base unit:
S004LB0600045 / S004LV0600045
input
100-240VAC
50/60Hz
output 6VDC 450mA
Battery Information
2 x1.2V AAA size 400mAh NiMH
150mA,
Risk of explosion if battery is replaced by an incorrect type
Dispose of used batteries according to the instructions.
15
CE DECLARATION
This product is in compliance with the essential requirements and other
relevant provisions of the R&TTE directive 1999/5/EC.
The Declaration of conformity can be found on: www.aegtelephones.eu
16
DISPOSAL OF THE DEVICE (ENVIRONMENT)
At the end of the product lifecycle, you should not throw this product into
the normal household garbage but bring the product to a collection point
for the recycling of electrical and electronic equipments. The symbol on
the product, user guide and/or box indicate this. Some of the product
materials can be re-used if you bring them to a recycling point. By reusing
some parts or raw materials from used products you make an important
contribution to the protection of the environment. Please contact your
local authorities in case you need more information on the collection
points in your area.
Batteries must be removed before disposing of the device. Dispose of
the batteries in an environmental manner according to your country
regulations.
17
CLEANING AND CARE
Do not clean any part of your phone with benzene, thinners or other
solvent chemicals as this may cause permanent damage which is not
covered by the Guarantee.
When necessary, clean it with a damp cloth.
Keep your phone system away from hot, humid conditions or strong
sunlight, and don‘t let it get wet.
UK
41
42
UK
43
© 2012 Binatone Electronics International Limited
All rights reserved
Subject to avaibility. Rights of modification reserved.
AEG is a registered trademark used under license from AB Electrolux (publ)
www.aegtelephones.eu
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising