Kuryakyn LED Rear Reflector Conversion Installation Instructions

INSTALLATION
LED REAR REFLECTOR CONVERSION
THANK YOU FOR CHOOSING KϋRYAKYN!
PROTECT YOURSELF AND OTHERS FROM POSSIBLE INJURY AND PROPERTY DAMAGE OR LOSS. PAY CLOSE ATTENTION TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS, AND NOTICES REGARDING THE INSTALLATION, USE, AND CARE OF THIS
PRODUCT.
THIS INDICATION ALERTS YOU TO THE FACT THAT
IGNORING THE CONTENTS DESCRIBED HEREIN CAN
RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.
This indication alerts you to the fact that ignoring
the contents described herein can result in minor or
moderate potential injury.
This indication alerts you to the fact that ignoring the
contents described herein may negatively affect product
performance and functionality or damage the product itself
or the product to which it is being attached.
MAKE SURE THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT:
1
1
1
LED Rear Reflector Conversion Assembly
Hardware Kit containing:
1
Dielectric Grease
2
Cable Ties
1
6-Pin Connector
1
Y-Adapter
Installation Instructions
TOOLS SUGGESTED:
Set of metric hex wrenches, set of metric wrenches, and a Phillips head screw driver
These installation instructions contain important information.
Ensure that the end user receives this copy and is aware of its
importance for future reference.
7356
CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS
[email protected]
or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products
sold hereunder, shall be free of defects in
materials and workmanship for a period of one
(1) year from the date of purchase by the
consumer excepting the following provisions:
● Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt
showing the date the customer purchased the
product(s).
●The product must be properly installed,
maintained and operated under
normal conditions.
●Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated
products.
●Küryakyn shall not be liable for any
consequential and incidental damages, including
labor and paint, resulting from failure of a
Küryakyn product, failure to deliver, delay in
delivery, delivery in nonconforming condition, or
for any breech of contract or duty between
Küryakyn and a customer.
●Küryakyn products are often intended for use in
specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
●Küryakyn electrical products are warranted for
one (1) year from the date of purchase by the
consumer. L.E.D.’S contained in components of
Küryakyn products will be warranted for defects
in materials and workmanship for 3 years from
the date of purchase where as all other
components shall be warranted for one(1) year.
This includes, but is not limited to; control
modules, wiring, chrome & other components.
●Küryakyn makes no warranty of any kind in
regard to other manufacturer¹s products
distributed by Küryakyn. Küryakyn will pass on
all warranties made by the manufacturer and
where possible, will expedite the claim on behalf
of the customer, but ultimately, responsibility for
disposition of the warranty claim lies
with the manufacturer.
ABOUT OUR CATALOG
STEP 1
Read and understand all steps in the instructions before starting the installation.
Park the motorcycle on a hard, level surface and turn off the ignition. Allow the exhaust system to cool.
VISIBILITY IS A MAJOR CONCERN FOR MOTORCYCLISTS. A LIGHTING MALFUNCTION CAN RESULT IN
DEATH OR SERIOUS INJURY. ENSURE ALL LIGHTING
FUNCTIONS CORRECTLY BEFORE OPERATING THE
MOTORCYCLE.
7356-21GL-0714
-cont.-
For purchasing Küryakyn® products, you
can receive a complete catalog free of charge.
Send the Proof-of-Purchase below with your
address to: Küryakyn
454 County Road V V
Somerset, WI 54025-9031
Please indicate either Accessories Catalog for
Harley-Davidson® or GL & Metric Cruisers.
Be sure to ask your local dealer about other
Küryakyn® products, the motorcycle parts and
accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights
reserved.
STEP 2
Refer to PIC 1. Remove the rear fender panel.
STEP 3
Refer to PIC 2. Separate the license-plate lightconnector.
STEP 4
Remove the existing reflector; set it aside, it will not
be reused.
STEP 5
Refer to PIC 3. On the license plate-side of the
panel, enlarge the locating hole to 1/4” in diameter.
STEP 6
Remove the nut and washer from the included LED
Rear Reflector Conversion Assembly.
STEP 7
Route the Reflector wiring through the 1/4” hole.
PIC 1
REMOVE THE FOUR HEX SCREWS,
THEN GENTLY PULL THE REAR
FENDER PANEL AWAY FROM THE
BIKE
Secure the Reflector to the panel with the nut and
washer.
STEP 8
Refer to PIC 4. Locate the included 6-Pin Connector.
Insert the RED wire into the 5 slot; BLACK wire into
the 4 slot; WHITE wire in the 3 slot.
Dielectric grease inhibits moisture
and prevents corrosion. Kuryakyn
recommends the use of the included dielectric grease on ALL
electrical connections. Apply dielectric grease directly to mating
surfaces.
STEP 9
Follow the instructions included with the Accessory
Harness (‘12-’14 GL1800 require P/N 3230; All F6B
require P/N 3234; available separately from
Kuryakyn).
Apply Dielectric Grease to the included Y-Adapter
and connect it to the Accessory Harness connectors.
STEP 10
PIC 2
ON THE BACKSIDE OF THE PANEL, PRESS THE TAB DOWN
AND GENTLY PULL THE CONNECTOR TO SEPARATE
PIC 3
ENLARGE HOLE IN
PANEL TO 1/4”
Connect the Reflector to the Y-Adapter.
Use the included Cable Ties to
secure the wiring away from moving parts, pinch points, or extreme heat. Kuryakyn will not provide warranty coverage on any
electrical component that fails
due to pinched, crimped, broken,
abraded, melted, or frayed wires.
LICENSE PLATESIDE OF PANEL
STEP 11
Reconnect the license-plate light-connector.
STEP 12
Turn IGN ON and test for proper operation of ALL lights.
STEP 13
Reinstall the rear fender panel.
Ride On!
It is the end user’s responsibility to ensure that all of
the fasteners (including pre-assembled) are tightened
before operation of the motorcycle. Küryakyn will not
provide warranty coverage on products or components
lost or damaged due to improper installation or lack of
maintenance. Periodic inspection and maintenance are
required on all fasteners.
LED REAR REFLECTOR CONVERSION
PIC 4
INSERT WIRES EXACTLY AS SHOWN
5
4
3
PAGE
2
INSTALLATION