Daewoo | CML-523BM | Service manual | Daewoo CML-523BM Service manual

Daewoo CML-523BM Service manual
Service Manual
LCD COLOR MONITOR
Model : CML-523BM
DAEWOO LUCOMS CO., LTD.
http://www.lucoms.com
MAY. 2004
CONTENTS
SAFETY PRECAUTIONS
2
GENERAL SAFETY INFORMATION
3
SERVICING PRECAUTIONS
4
TECHNICAL INFORMATION
8
GENERAL INFORMATION
8
PIN CONNECTOR
9
CAUTIONS FOR ADJUSTMENT AND REPAIR
9
OPERATION & ADJUSTMENT
10
ALIGNMENT PROCEDURE
16
TROUBLESHOOTING HINTS
17
BLOCK DIAGRAM
25
SCHEMATIC DIAGRAM
26
PCB PATTERN
34
INFORMATION OF PART DESCRIPTION
38
ELECTRICAL PARTS LIST
39
1
SAFETY PRECAUTIONS
CAUTION: No modifications of any circuits should be attempted. Service work should be performed
only after you are thoroughly familiar with all of the following safety checks and servicing
guidelines.
◆ Safety Check
Care should be taken while servicing the inverter that generates the high voltage to lighten CCFL of the
LCD panel.
◆ Fire & Shock Hazard
• Insert an isolation transformer between the analog color display and AC power line before servicing the
chassis.
• When servicing, pay close attention to the original lead dress especially in the high voltage circuit area;
if a short circuit is found, replace all parts which have been overheated as a result of the short circuit.
• All the protective devices must be reinstalled per original design.
• Soldering must be inspected for possible cold solder points, frayed leads, damaged insulation, solder
splashes or sharp solder points. Be certain to remove all foreign materials.
2
GENERAL SAFETY INFORMATION
◆ Terms in the manual
CAUTION
Statements identify conditions or practices that could result in damage to the equipment or
other property.
WARNING Statements identify conditions or practices that could result in personal injury or loss of
life.
◆ Terms as marked on equipment
CAUTION
Statements indicate a personal injury hazard not immediately accessible as one reads the
marking or a hazard which is properly included on the equipment itself.
WARNING Statements are clearly concerning indicated personal injury hazards.
◆ Symbols in the manual
The symbols indicate where applicable cautionary or other information is to be found.
◆ Symbols as marked on equipment
Protective GROUND terminal
◆ High Voltage Warning
And Critical Component Warning Label
The following warning label is on the inverter isolation case.
3
SERVICING PRECAUTIONS
CAUTION: Before servicing instruments covered by this service manual, its supplements, and
addendum, please read and follow the SAFETY PRECAUTIONS of this manual.
NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any
of the safety precautions on page 1 of this manual, always follow the safety precautions.
Remember: Safety First.
◆ General Servicing Precautions
1. Always unplug the AC power cord from the AC power source before:
a. Removing or reinstalling any component, circuit board, module, or any other instrument assembly.
b. Disconnecting or reconnecting any electrical plug or other electrical connection.
c. Connecting a test substitute in parallel with an electrolytic capacitor in the instrument.
CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors
may result in a explosion.
2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage
measuring device (DVM, FETVOM. etc.) equipped with a suitable high voltage probe. Do not test high
voltage by “drawing an arc”.
3. Do not any spray chemicals on or near this instrument, or any of its assemblies.
4. Unless otherwise specified in this service manual, only clean electrical contacts by applying the
following mixture to the contacts with a pipe cleaner, cotton-tipped stick, or comparable nonabrasive
applicator: 10% (by volume) Aceton and 90% (by volume) isopropyl alchohol (90%-99% strength).
CAUTION: This is a flammable mixture. Unless specified in this service manual, lubrication of
contacts is not required.
5. Do not apply AC power to this instrument and/or any other of its electrical assemblies unless all the
solid-state device heat sinks are correctly installed.
6. Always connect the test instrument ground lead to the appropriate instrument chassis ground before
connecting the test instrument positive lead. Always remove the test instrument ground lead last.
7. Only use the test fixtures specified in this service manual with this instrument.
4
SERVICING PRECAUTIONS
◆ Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity.
Such components are commonly called Electrostatically Sensitive (ES) Devices.
The typical examples of ES devices are integrated circuits, some field-effect transistors, and
semiconductor “chip” components. The following techniques should be used to help reduce the incidence
of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly,
wipe off any electrostatic charge on your body by touching any known earth ground. Alternatively,
obtain and wear a commercially available discharging wrist strap device which should be removed for
potential shock reasons prior to applying power to the unit under testing conditions.
2. After removing the electrical assembly equipped with ES devices, place the assembly on a conductive
surface such as aluminum foil to prevent electrostatic charge buildup or exposure to the assembly.
3. Only use a grounded-tip soldering iron to solder or unsolder ES devices.
4. Only use an anti-static type solder removal device. Some solder removal devices not classified as “antistatic” can generate enough electrical charges to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate enough electrical charges to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are
ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together
by conductive foam, aluminum foil, or comparable conductive material).
7. Immediately before removing the protective material from the leads of replacement ES devices, touch
the protective material to the chassis or circuit assembly into which the device will be installed.
CAUTION: Be sure that no power is applied to the chassis or circuit, and observe all other safety
precautions.
8. Minimize bodily movements when handling unpackaged replacement ES devices. (Otherwise harmful
motion such as the brushing together clothes fabric or the lifting your foot from a carpeted floor can
generate enough static electricity to damage ES devices).
◆ General Soldering Guidelines
1. Use a grounded-tip, low-wattage soldering iron with appropriate tip size and shape that will maintain
tip temperature between a 550°F-660°F (288°C-316°C) range.
2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead.
3. Keep the soldering iron tip clean.
4. Throughly clean the surface to be soldered. Use a small wire-bristle (0.5 inch or 1.25cm) brush with a
metal handle. Do not use freon-propelled spray-on cleaners.
5. Use the following soldering technique:
a. Allow the soldering iron tip to reach normal temperature (550°F to 660°F or 288°C to 316°C)
b. Hold the soldering iron tip and solder strand against the component lead until the solder melts.
c. Quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil,
and hold it there until the solder flows onto and around both the component lead and the foil.
d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush.
CAUTION: Work quickly to avoid overheating the circuit board printed foil.
5
SERVICING PRECAUTIONS
FIGURE 1. USE SOLDERING IRON TO PRY LEADS
◆ IC Removal/Replacement
Some utilized chassis circuit boards have slotted (oblong) holes through which the IC leads are inserted
and then bent flat against the circuit foil. When holes are slotted, the following technique should be used
to remove and replace the IC. When working with boards using the familiar round hole, use the standard
technique as outlined in paragraphs 5 on the page under the title of general soldering guidelines.
◆ Removal
1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the
soldering iron tip as the solder melts.
2. Draw away the melted solder with an anti-static suction-type solder removal device (or with
desoldering braid before removing the IC.
◆ Replacement
1. Carefully insert the replacement IC in the circuit board.
2. Carefully bend each IC lead against the circuit foil pad and solder it.
3. Clean the soldered areas with a small wire-bristle brush. (lt is not necessary to reapply acrylic coating
to the area).
◆ “Small-Signal” Discrete Transistor Removal/Replacement
1. Remove the defective transistor by clipping its leads as close as possible to the component body.
2. Bend the ends of each of three leads remaining on the circuit board into a “U” shape.
3. Bend the replacement transistor leads into a “U” shape.
4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board
and crimp the “U” with long nose pliers to ensure metal-to-metal contact, then solder each connection.
◆ Power IC, Transistor or Devices Removal/Replacement
1. Heat and remove all solders from the device leads.
2. Remove the heatsink mounting screw (if applicable).
3. Carefully remove the device from the circuit board.
4. Insert new device in circuit board.
5. Solder each device lead and then clip off excess lead.
6. Replace heatsink.
6
SERVICING PRECAUTIONS
◆ Diode Removal/Replacement
1. Remove defective diode by clipping its leads as close as possible to diode body.
2. Bend the two remaining leads perpendicularly to the circuit board.
3. Observing diode polarity, wrap each lead out of the new diode around the corresponding lead on the
circuit board.
4. Securely crimp each connection and solder it.
5. Inspect the solder joints of the two “original” leads on the circuit board copper side. If they are not
shiny, reheat them and apply additional solder if necessary.
7
TECHNICAL INFORMATION
Panel
Synchronization
Video Bandwidth
Max Resolution
Colors
Display Area
PC Input Signal
Speaker
Plug and Play
Power Source
Power Consumption
Dimension-W x H x D
Size
Pixel Pitch
Viewing Angle
Contrast Ratio
Brightness
Color Filter
Horizontal
Vertical
Sync
Video
Audio
Max. Output
Weight-net/gross
Power Saving
Tilt Range
Operating Temperature
15-inch (38cm) diagonal
0.297 x 0.297 mm
70°(Right/Left)
70°(up), 60°(down)
350:1 contrast ratio (typ)
250cd/m2 brightness (typ)
RGB vertical stripe
30-62 KHz
50-75Hz
80MHz
1024 x 768 @75Hz
16.2M Colors
304.1mm x228.1mm
H/V separate (TTL)
15 pin mini D-sub(Analog RGB)
Stereo MiniJack Input & Output
2W(Left 1W+Right 1W)
VESA DDC Compatible
100-240 Vac, 50/60 Hz (Free Voltage)
26W
370 x 352 x 205mm (with stand)
370 x 312 x 60 mm (without stand)
4.2/5.5Kg
EPA, VESA DPMS, Nutek Compliant
5° forward, 30° backward
10 ~ 40°C /50 ~ 104°F
8
GENERAL INFORMATION
This TFT LCD monitor automatically scans all horizontal frequencies from 30KHz to 62KHz. This TFT LCD monitor
supports IBM PC, PC/XT, PC/AT, personal System/2 (PS/2), Apple Macintosh, and compatible users crisp text and vivid
color graphics display when using the following graphics adapters : (VGA, Super VGA, VESA, XGA, SXGA and Apple
Macintosh Video Card). And so, this TFT LCD monitor has a maximum horizontal resolution of 1024 dots and a maximum
vertical resolution of 768 lines for superior clarity of display.
By accepting analog signal inputs which level is zero to 0.7 Volts. This TFT LCD monitor can display 16.7M colors
depending on the graphics adapter and software being used.
◆ Abbreviations
ADJ
AFC
TFT-LCD
CCFL
H.SYNC
OSC
P.S.U
PWA
R.G.B
V.Sync
ADC
Adjustment
Automatic Frequency Control
Thin Film Transistor Liquid Crystal Diplay
Cold Cathode Fluorescent Lamp
Horizontal Synchronization
Oscillator
Power Supply Unit
Printed Circuit Board Wiring Assembly
Red, Green, Blue
Vertical Synchronization
Analog Digital Converter
PIN CONNECTOR
Pin
Signal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Red
Green
Blue
GND
GND
GND - Red
GND - Green
GND - Blue
+5Vdc
GND - H.Sync
GND - V.Sync
Bi-directional Data (SDA)
Horizontal Sync
Vertical Sync (VCLK)
Data Clock (SCL)
1
6
10
15
Arrangement of 15-pin D-sub connector
CAUTIONS FOR ADJUSTMENT AND REPAIR
• The white balance adjustment has been done by a color analyzer in factroy. The adjustment procedure, described in
the service manual is made by a visual check.
• Allow 20 minutes warm-up time for the display before checking or adjusting only electrical specification or
function.
• Reform the leadwire after any repair work.
◆ Caution For Servicing
• In case of servicing or replacing inverter, high voltage sometimes remains in the output of the inverter. Completely
discharge high voltage before servicing or replacing inverter to prevent a shock to the serviceman.
9
OPERATION AND ADJUSTMENT
<< L523BM >>
Control Panel
2 POWER Indicator
Shows both normal operation and
power management status with
power indicator light.
1 POWER
Switches the monitor on and
off.
2
AUTO
EXIT
MENU
1
BRIGHTNESS
POWER LIGHT
7
6
3
( *)
5
4
3
4
Moves cursor to the right or low
window in the OSD window and
increases the value of any
selected function.
5 MENU
Turns the OSD window on.
7 AUTO ( * )
Launches the AUTO TRACKING
function directly.
( *)
Moves cursor to the left or high
window in the OSD window and
decreases value of any selected
function.
6 EXIT/POWER LIGHT
Turns the OSD (On-Screen
Display) window off and moves
from sub menu to top menu in the
OSD window.
While the OSD screen is off, you
can adjust the screen brightness
according to each situation.
( * ) : Hot Key
10
OPERATION AND ADJUSTMENT
Key Process
1024X768
60K
75
U T I L I TY
U TIL ITY
U TIL ITY
OSD
OSD
SH AR PN ESS
SH AR PN ESS
OSD OFF
HOT KEY
AUTO
EXIT
AU TO T R AC K I N G
POWER LIGHT
POWER LIGHT
PC MODE
When there is no OSD, if you press this
AUTO button, you can use the best display
performance fit for a current mode.
GAME MODE
MOVIE MODE
The screen will be brightened progressively by
10%. If you carry out general PC works such as
document edition on the Movie mode,you may
shorten the life span of LCD panel. Thus,it is
recommended to verify the selected mode before
use.
BRIGHTNESS
When there is no OSD, if you press this
BRIGHTNESS button, you can adjust the
brightness directly.
: decreases brightness
: increases brightness
11
OPERATION AND ADJUSTMENT
Adjustment Procedure
No
Is the H.Size
proper?
Adjust the CLOCK
control.
Yes
Is the
noise displayed on
the screen?
Perform the AUTO
POSITION.
No
Yes
Perform the AUTO
TRACKING.
Is the
noise displayed on
the screen yet?
No
Yes
Adjust the CLOCK FINE
until the screen is
cleared.
Yes
Is the
noise displayed on
the screen yet?
No
End
12
OPERATION AND ADJUSTMENT
OSD Functions
<< OSD FUNCTIONS WITH USING PC >>
ICON
CONTROL
FUNCTIONS
VOLUME
Adjust audio volume, mute sound.
CLOCK
Adjust the width (horizontal size) of the screen image.
CLOCK FINE
Sharpen the focus by aligning the illuminated pixels and adjust until the screen
image looks focused, crisp and sharp. Adjusting the CLOCK FINE after the
CLOCK adjustment will produce a clear screen.
AUTO TRACKING
Adjust the horizontal & vertical picture image quality and size.
COLOR
TEMPERATURE
Choose different preset color temperatures or set your own customized color
parameters.
R
RED CONTROL
Adjust the red color.
G
GREEN
CONTROL
Adjust the green color.
B
BLUE CONTROL
Adjust the blue color.
H. CENTER &
Adjust the position of the display horizontally (left or right) and vertically (up or
down).
V. CENTER
OSD
SHARPNESS
Adjust the display image quality (if the screen proceed to scaling up).
OSD POSITION
Adjust the OSD position horizontally (left or right) and vertically (up or down).
OSD TIME OUT
Adjust the display OSD Menu.
STATUS
Display horizontal & vertical frequency and polarity.
RECALL
Reset the screen to the Factory Preset Display Settings.
13
OPERATION AND ADJUSTMENT
ICON
CONTROL
FUNCTIONS
AUTO POSITION
Choose automatically the proper horizontal position and vertical position & size
of the screen image.
LANGUAGE
Select language for OSD (6 languages).
CONTRAST
Adjust the contrast of image, the difference between light and dark areas on the
screen.
14
OPERATION AND ADJUSTMENT
Self Diagnosis
If there is no image, the Self Diagnosis screen will be displayed. Self Diagnosis function checks if the
status of the monitor screen is No Signal, Out of range or None support.
“No Signal” screen is displayed when the D-Sub signal connector is not
connected or the status of the monitor is on DPMS mode.
“Out of Range” screen is displayed when the applied frequency is under or over
normal range.
Normal range
(Non-interlaced mode only)
H : 30 - 62 KHz
V : 50 - 75 Hz
“None support” screen is displayed when the applied frequency is under or over
factory preset timings.
Check cable screen is displayed when the
signal cable is disconnected.
15
ALIGNMENT PROCEDURE
Standard Check point
1. Power source : 100 - 240Vac, 50/60Hz.
2. Aging : Take at least 20 minutes warm-up time.
3. Signal
• Video input : Analog 0.7Vpp 75Ω terminal positive polarity
• Synchronizing : acceptable negative or positive at TTL level
• Max. Resolution :
15”-1024 x 768@75Hz
• Frequency:
15”- Horizontal : 30KHz - 62KHz
Vertical : 50Hz - 75Hz (available only non interlace mode)
Adjustment
1. Sharpness set to 0%
2. Contrast set to 100%
3. Brightness set to 100%
4. Switching to factory alignment mode
Press power key with Brightness left key at the power off status.
5. Set up the tracking
See the SVC manual at page 14th.
6. Switching to user’s mode
If turn-off and turn-on then switched to user’s mode.
* All of adjusted data stores by fade out of OSD.
16
TROUBLESHOOTING HINTS
1. Abnormal mode detect
1-1. Abnormal mode detect for PC Source
Abnormal mode
detect
Yes
Is a input
H-sync of Scaler(pin 126,
U6) correct?
No
Yes
Trouble
in Scaler(U6).
17
Trouble in the H-sync
input circuit.
TROUBLESHOOTING HINTS
2. Trouble in Power on
Trouble in
Power on
Yes
Is the
Power LED toggled
between on and
off?
On
Refer to No video
or No raster.
Off
Is the power
cord well
connected?
No
Check if the power switch
is on position and
Connect the power
cord correctly.
Yes
Check the
waveform of pin 17
of -com(U4).
No
Trouble in Scaler(U6).
Yes
Is Vcc 5V line
normal(pin 8 of CON1)?
No
Yes
Check on Scaler(U6).
18
Check the power board
(Vcc 5V of CN2A).
TROUBLESHOOTING HINTS
3. No Raster
No Raster
Yes
Check the
output of Q1 or
pin 15 of U4.
low
Trouble in pin 15
of -com.
No
Check the output
of D811 12V line
(power board).
high
Is 12V
plugged in pin5
of CN2(power
board)?
Yes
Is the output of
inverter correct?
No
Replace the inverter.
Yes
Replace a LCD panal.
19
TROUBLESHOOTING HINTS
4. One color is missing
One color is missing
Yes
Is the OSD color
normal?
No
Check the output
signal of Scaler.
Yes
Is the input
signal normal?
No
Check the video signal
cable or R,G,B
con-ass’y.
Yes
Are the
R,G,B Digital values
(every eight bits) correct
on Scaler output
stage?
No
Yes
Trouble in the soldering
of R,G,B data lines
from output of Scaler
to Scaler(U6).
20
Check the ambient
circuit of Scaler.
TROUBLESHOOTING HINTS
5. No Video
No Video
Yes
Has display image
only white?
No
Next page.
Yes
Check if
the CON3 wafer is
well connected at
the LCD panel.
No
Connection trouble.
Yes
Is pin 1
of U2 3.3V?
No
Check U2, its ambient
circuit and pin 14 of U8.
Yes
Check the output of scalier
(pin LAV 0P~3P, 0M~3M)
and soldering of CON3.
21
TROUBLESHOOTING HINTS
5-1. No Video
Black
Yes
Is OSD normal?
No
3. No raster
Yes
Is the contrast
at its maximum?
No
Set the contrast
up to Max.
Yes
Is the output
of Scaler correct?
No
Is the input of
Scaler correct?
No
Yes
Yes
Replace the main board
(or replace Scaler).
Check If
the CON3 wafer is
well connected at
the LCD panel.
22
TROUBLESHOOTING HINTS
6. Power Problem
Power problem
Yes
Is the power
cord well
connected?
Check if the power
cord is correctly
connected.
No
Yes
Check
5V, 3.3V, 12V
of CN4.
Yes
Check the main board.
23
TROUBLESHOOTING HINTS
7. Sound Problem
No Sound
Is
Audio-in OK?
(pin 10, 14 at U7)
No
Check Audio-in
jack(J1).
Yes
Is VCC(Pin15,16)
of Audio IC(U7)
12V?
No
Check VCC 12V line.
Yes
Is Audio-out
OK?
No
Yes
Is Mute ON?
No
Check speaker.
Yes
Change Mute OFF.
24
Check Auido IC(U7).
BLOCK DIAGRAM
25
SCHEMATIC DIAGRAM(L523BM)
26
SCHEMATIC DIAGRAM
27
SCHEMATIC DIAGRAM
28
SCHEMATIC DIAGRAM
29
SCHEMATIC DIAGRAM
30
SCHEMATIC DIAGRAM
31
SCHEMATIC DIAGRAM
32
SCHEMATIC DIAGRAM
33
PCB PATTERN
34
PCB PATTERN
35
PCB PATTERN
36
PCB PATTERN
37
INFORMATION OF PART DESCRIPTION
Important Safety Notice
Components identified with the International Symbol have special characteristics important for safety.
When replacing any components, use only manufacturer’s specified parts.
Abbreviation of Description
RESISTOR Description
Tolerance
F
± 1%
J
± 5%
K
± 10%
M
± 20%
G
± 2%
Example:
Fig &
Index
Part No
Description
Resistors
RD-4Z820J
Carbon : 82J
HRFS472JBA Chip 4.7K OHM J
R101
R30
CAPACITOR Description
C
D
F
J
K
P
Z
Tolerance
± 0.25pF
± 0.5%
± 1pF
± 5%
± 10%
± 100% ~ 0%
± 80% ~ –
Example:
Fig &
Index
C28
C63
C44
Part No
Description
Capacitors
HCFK104ZBA
Chip Cera 50V Z
HCBK393KBA
Chip Cera 50V K
HCQK102JBA
Chip Cera 50V J
38
ELECTRICAL PARTS LIST
The components identified by mark
have special characteristics important for safety and x-ray radiation.
These should be replaced only with the types specified in the parts list.
LOC
Z1010
CA001
LCD
LIPS
YF001
YF010
00010
00010
00020
00030
00020
00010
00020
00030
00030
00010
00020
00030
00040
00050
00060
YF020
YF030
YF031
YF040
YF041
YF050
YF070
YF080
YF090
YF100
YF110
YF120
Z2010
C862
C863
CN1
CN2
CN3
CON1
CON2
F801
F801A
F801B
J1
J2
J3
U4
U7
YM010
YM020
YM030
Z3010
PART-CODE
PCFMCAG204
99707K0002
9979615051
DDML1501—
9974116710
99720221A9
9972022120
22211102H4
223126GY06
2233020801
9975112902
22211102H4
223126GY06
2233020801
9974828201
2221080788
223126GY03
2233020801
9974826710
9977921700
7173301011
9977249200
7003250511
7003250811
7173301011
7171301011
7173300611
7173300611
7173300611
7S103B30B1
9978300038
9977912902
9976811600
PCMPM1G190
CH1FDF103M
CH1FDF103M
9979220039
9979200317
9979220085
9979220118
9979220087
5F3CB3122L
9977410900
9977410900
9979100014
9979100022
9979200217
1WT61P4L44
1TDA7496L9973924301
9975211907
7173300611
PCMPJ1G190
PART-NAME
PART-DESC
COVER FRONT AS
CONN AS
LCD PANEL
LCD INVERTER + POWER
FRAME
COVER FRONT AS
COVER FRONT
RESIN HIPS
PAINT ACRYL
THINNER
DECO FRONT
RESIN HIPS
PAINT ACRYL
THINNER
BUTTON TACT
RESIN ABS
PAINT ACRYL
THINNER
BUTTON POWER
LENS LED
SCREW TAPPTITE
SHIELD REAR
SCREW MACHINE
SCREW MACHINE
SCREW TAPPTITE
SCREW TAPTITE
SCREW TAPPTITE
SCREW TAPPTITE
SCREW TAPPTITE
SCREW SPECIAL
SPEAKER ASSY
TAPE ACETATE
WIRE SADDLE
PCB MAIN MANUAL AS
C CERA AC
C CERA AC
CONN WAFER
SOCKET AC INLET
CONN WAFER
CONN WAFER
CONN WAFER
FUSE CERA
FUSE CLIP
FUSE CLIP
JACK PHONE
STEREO PHONE JACK
D-SUB 15P ANGLE
IC MICOM
IC AUDIO AMP
BKT I/O
PLATE I/O
SCREW TAPPTITE
PCB MAIN SMD AS
39
CML-523BM-4L
12507HS-20+12507HS-20+1571#30=80
LM150X06 LVDS
DML-1501 (PEC)
E.G.I T=0.8 ( LG-PHL TYPE )
L523BM C/FRONT AS
HIPS GRAY SPRAY
CH HR-1360 GY-340A G7851
GY-5108BP
AC THINNER
HIPS GRAY SPRAY
CH HR-1360 GY-340A G7851
GY-5108BP
AC THINNER
HB-ABS SILVER SPRAY
HF-0680 G7642B(HB)
SILVER SV3109BP
AC THINNER
HIPS DARK GRAY SPRAY
ACRYL (CLEAR)
TT2 BIN 3X10 MFZN
E.G.I T=0.8
BIN 2.5X5 MFZN
BIN 2.5X8 MFZN
TT2 BIN 3X10 MFZN
TT2 PAN 3X10 MFZN
TT2 BIN 3X6 MFZN
TT2 BIN 3X6 MFZN
TT2 BIN 3X6 MFZN
M/C BIN 3*8 TW(B) MFZN
523BM R4020QC02
ACETATE 0.27*30M
NYLON 66 DAWS 2N
CML-523BMW-L
2.5KV 0.01MF M AC250V
2.5KV 0.01MF M AC250V
YAW396-03AV(ANGLE)
ST-03B-BP
SMAW200-04/68163-0410
YDW200-10
SMAW200-06/68163-0610
SEMKO TL 3.15AH 250V MF51
BSP3-H T0.4 SN 5.2
BSP3-H T0.4 SN 5.2
“STEREO 3.5P, ST-029B-03BU”
ST-328NB-01
15P DDC BLUE W/OUT SCREW
WT61P4-L44
TDA7496L
E.G.I. T=1.0
P.C T=0.5 (L523BMW)
TT2 BIN 3X6 MFZN
CML-523BMW-L
ELECTRICAL PARTS LIST
LOC
C1
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C21
C22
C23
C24
C25
C26
C27
C28
C29
C30
C31
C32
C33
C34
C35
C36
C37
C38
C39
C40
C41
C42
C43
C44
C45
C46
C47
C48
C49
C5
C50
C51
C52
C53
C54
C55
C56
C57
C58
C59
C6
C60
C61
PART-CODE
HCFK104ZBA
HCEEF101MD
HCFK104ZBA
HCBK103KBA
HCEEF101MD
HCFK104ZBA
HCFD105ZBA
HCEEF101MD
HCFK104ZBA
HCBK103KBA
HCFK104ZBA
HCEEF101MD
HCFK104ZBA
HCEEF101MD
HCFK104ZBA
HCFK104ZBA
HCFK104ZBA
HCEEF101MD
HCEEF101MD
HCFK104ZBA
HCFK104ZBA
HCEKF100MC
HCEDC470MC
HCFK104ZBA
HCEDC470MC
HCQK220JBA
HCFK104ZBA
HCEDC470MC
HCQK220JBA
HCFK104ZBA
HCFK104ZBA
HCQK101JBA
HCQK471JBA
HCFK104ZBA
HCFK104ZBA
HCEKF100MC
HCFK104ZBA
HCFK104ZBA
HCFK104ZBA
HCFK104ZBA
HCFK104ZBA
HCEEF101MD
HCFK104ZBA
HCFK104ZBA
HCEKF100MC
HCFK104ZBA
HCFK104ZBA
HCFK104ZBA
HCFK104ZBA
HCEKF100MC
HCFK104ZBA
HCFK104ZBA
HCFK104ZBA
HCFK104ZBA
HCFK104ZBA
PART-NAME
PART-DESC
C CHIP CERA
C CHIP ELECTRO
C CHIP CERA
C CHIP CERA
C CHIP ELECTRO
C CHIP CERA
C CHIP CERA
C CHIP ELECTRO
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP ELECTRO
C CHIP CERA
C CHIP ELECTRO
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP ELECTRO
C CHIP ELECTRO
C CHIP CERA
C CHIP CERA
C CHIP ELECTRO
C CHIP ELECTRO
C CHIP CERA
C CHIP ELECTRO
C CHIP CERA
C CHIP CERA
C CHIP ELECTRO
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP ELECTRO
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP ELECTRO
C CHIP CERA
C CHIP CERA
C CHIP ELECTRO
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP ELECTRO
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
50V Y5V 0.1MF Z 1608
MV 16V 100MF M 6.3DX5.7H
50V Y5V 0.1MF Z 1608
50V X7R 0.01MF K 1608
MV 16V 100MF M 6.3DX5.7H
50V Y5V 0.1MF Z 1608
Y5V 10V 1MF Z 1608
MV 16V 100MF M 6.3DX5.7H
50V Y5V 0.1MF Z 1608
50V X7R 0.01MF K 1608
50V Y5V 0.1MF Z 1608
MV 16V 100MF M 6.3DX5.7H
50V Y5V 0.1MF Z 1608
MV 16V 100MF M 6.3DX5.7H
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
MV 16V 100MF M 6.3DX5.7H
MV 16V 100MF M 6.3DX5.7H
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
MV 16V 10MF D4.0XH5.2
MV 6.3V 47MF 5DX5.2H
50V Y5V 0.1MF Z 1608
MV 6.3V 47MF 5DX5.2H
50V CH 22PF J 1608
50V Y5V 0.1MF Z 1608
MV 6.3V 47MF 5DX5.2H
50V CH 22PF J 1608
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
50V CH 100PF J 1608
50V CH 470PF J 1608
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
MV 16V 10MF D4.0XH5.2
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
MV 16V 100MF M 6.3DX5.7H
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
MV 16V 10MF D4.0XH5.2
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
MV 16V 10MF D4.0XH5.2
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
40
ELECTRICAL PARTS LIST
LOC
C62
C63
C64
C65
C66
C67
C68
C69
C7
C70
C71
C72
C73
C74
C75
C76
C77
C78
C79
C8
C80
C81
C82
C83
C84
C85
C86
C87
C88
C89
C9
C90
C91
C92
CON3
D1
D10
D2
D3
D4
D5
D6
D7
D8
D9
FB1
FB2
L1
L10
L11
L12
L13
L2
L3
L4
PART-CODE
HCEKF100MC
HCFK104ZBA
HCFK104ZBA
HCFK104ZBA
HCFK104ZBA
HCFK104ZBA
HCEKF100MC
HCFK104ZBA
HCBK103KBA
HCFK104ZBA
HCQK220JBA
HCQK220JBA
HCFD105ZBA
HCEPF471ME
HCEPF471ME
HCFD105ZBA
HCFK104ZBA
HCEPF471ME
HCEPF221ME
HCFK104ZBA
HCFK104ZBA
HCFD105ZBA
HCFD105ZBA
HCFD105ZBA
HCBK102KBA
HCQK200JBA
HCQK200JBA
HCQK200JBA
HCFD105ZBA
HCFD105ZBA
HCEEF101MD
HCFD105ZBA
HCQK330JBA
HCQK221JBA
9979220160
DKDS193—DZZ02W5R6V
DZZ02W5R6V
DZZ02W5R6V
DBAV99——
DBAV99——
DBAV99——
DZZ02W5R6V
DZZ02W5R6V
DZZ02W5R6V
HFFHH1M601
HFFHH1M601
HFFHH1M601
HFFHH1M601
HFFHH1M601
HFFHH1M601
HFFHH1M601
HFFHH1M601
HFFHH1M601
HFFHH1M601
PART-NAME
PART-DESC
C CHIP ELECTRO
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP ELECTRO
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP ELECTRO
C CHIP ELECTRO
C CHIP CERA
C CHIP CERA
C CHIP ELECTRO
C CHIP ELECTRO
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP CERA
C CHIP ELECTRO
C CHIP CERA
C CHIP CERA
C CHIP CERA
LVDS WAFER
DIODE
DIODE ZENER
DIODE ZENER
DIODE ZENER
DIODE CHIP
DIODE CHIP
DIODE CHIP
DIODE ZENER
DIODE ZENER
DIODE ZENER
COIL CHIP BEAD
COIL CHIP BEAD
COIL CHIP BEAD
COIL CHIP BEAD
COIL CHIP BEAD
COIL CHIP BEAD
COIL CHIP BEAD
COIL CHIP BEAD
COIL CHIP BEAD
COIL CHIP BEAD
MV 16V 10MF D4.0XH5.2
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
MV 16V 10MF D4.0XH5.2
50V Y5V 0.1MF Z 1608
50V X7R 0.01MF K 1608
50V Y5V 0.1MF Z 1608
50V CH 22PF J 1608
50V CH 22PF J 1608
Y5V 10V 1MF Z 1608
MV 16V 470MF M 8.0DX10H
MV 16V 470MF M 8.0DX10H
Y5V 10V 1MF Z 1608
50V Y5V 0.1MF Z 1608
MV 16V 470MF M 8.0DX10H
MV 16V 220MF D8.0XH1.0
50V Y5V 0.1MF Z 1608
50V Y5V 0.1MF Z 1608
Y5V 10V 1MF Z 1608
Y5V 10V 1MF Z 1608
Y5V 10V 1MF Z 1608
50V X7R 1000PF K 1608
50V CH 20PF J 1608
50V CH 20PF J 1608
50V CH 20PF J 1608
Y5V 10V 1MF Z 1608
Y5V 10V 1MF Z 1608
MV 16V 100MF M 6.3DX5.7H
Y5V 10V 1MF Z 1608
50V CH 33PF J 1608
50V CH 220PF J 1608
12507WR-20
KDS193
Z02W5.6V
Z02W5.6V
Z02W5.6V
BAV99
BAV99
BAV99
Z02W5.6V
Z02W5.6V
Z02W5.6V
HH-1M3216-601JT
HH-1M3216-601JT
HH-1M3216-601JT
HH-1M3216-601JT
HH-1M3216-601JT
HH-1M3216-601JT
HH-1M3216-601JT
HH-1M3216-601JT
HH-1M3216-601JT
HH-1M3216-601JT
41
ELECTRICAL PARTS LIST
LOC
L5
L6
L7
L8
L9
PCB
Q1
R1
R10
R11
R12
R13
R14
R15
R16
R17
R18
R19
R2
R20
R21
R22
R23
R24
R25
R26
R27
R28
R29
R3
R30
R31
R32
R33
R34
R35
R36
R37
R38
R39
R40
R41
R42
R43
R45
R46
R47
R48
R49
R5
R50
R51
R52
R53
R54
PART-CODE
HFFHH1M601
HFFHH1M601
HFFHH1M601
HFFHH1M601
HFFHH1M601
9979800612
TKTC3875SY
HRFS102JBA
HRFS472JBA
HRFS472JBA
HRFS101JBA
HRFS105JBA
HRFS472JBA
HRFS472JBA
HRFS103JBA
HRFS472JBA
HRFS472JBA
HRFS473JBA
HRFS102JBA
HRFS101JBA
HRFS101JBA
HRFS472JBA
HRFS101JBA
HRFS151JBA
HRFS151JBA
HRFS472JBA
HRFS103JBA
HRFS473JBA
HRFS473JBA
HRFS102JBA
HRFS101JBA
HRFS223JBA
HRFS101JBA
HRFS223JBA
HRFS151JBA
HRFS151JBA
HRFS223JBA
HRFS472JBA
HRFS472JBA
HRFS223JBA
HRFS101JBA
HRFS101JBA
HRFS102JBA
HRFS102JBA
HFFHH1M601
HRFS334JBA
HRFS102JBA
HRFS102JBA
HRFS000JBA
HRFS472JBA
HRFS101JBA
HRFS000JBA
HRFS101JBA
HRFS000JBA
HRFS101JBA
PART-NAME
PART-DESC
COIL CHIP BEAD
COIL CHIP BEAD
COIL CHIP BEAD
COIL CHIP BEAD
COIL CHIP BEAD
PCB MAIN
TR CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
COIL CHIP BEAD
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
HH-1M3216-601JT
HH-1M3216-601JT
HH-1M3216-601JT
HH-1M3216-601JT
HH-1M3216-601JT
CML-700C-3S T=1.6*225*110
KTC3875SY(RTK)
1/16 1K OHM J 1608
1/16 4.7K OHM J 1608
1/16 4.7K OHM J 1608
1/16 100 OHM J 1608
1/16 1M OHM J 1608
1/16 4.7K OHM J 1608
1/16 4.7K OHM J 1608
1/16 10K OHM J 1608
1/16 4.7K OHM J 1608
1/16 4.7K OHM J 1608
1/16 47K OHM J 1608
1/16 1K OHM J 1608
1/16 100 OHM J 1608
1/16 100 OHM J 1608
1/16 4.7K OHM J 1608
1/16 100 OHM J 1608
1/16 150 OHM J 1608
1/16 150 OHM J 1608
1/16 4.7K OHM J 1608
1/16 10K OHM J 1608
1/16 47K OHM J 1608
1/16 47K OHM J 1608
1/16 1K OHM J 1608
1/16 100 OHM J 1608
1/16 22K OHM J 1608
1/16 100 OHM J 1608
1/16 22K OHM J 1608
1/16 150 OHM J 1608
1/16 150 OHM J 1608
1/16 22K OHM J 1608
1/16 4.7K OHM J 1608
1/16 4.7K OHM J 1608
1/16 22K OHM J 1608
1/16 100 OHM J 1608
1/16 100 OHM J 1608
1/16 1K OHM J 1608
1/16 1K OHM J 1608
HH-1M3216-601JT
1/16 330K OHM J 1608
1/16 1K OHM J 1608
1/16 1K OHM J 1608
1/16 0 OHM J 1608
1/16 4.7K OHM J 1608
1/16 100 OHM J 1608
1/16 0 OHM J 1608
1/16 100 OHM J 1608
1/16 0 OHM J 1608
1/16 100 OHM J 1608
42
ELECTRICAL PARTS LIST
LOC
R55
R56
R57
R58
R59
R6
R60
R61
R62
R64
R65
R66
R67
R68
R69
R7
R70
R8
R9
U2
U3
U4S
U5
U6
Y1
Y2
Z2030
CA201
LED1
W5
W6
Z3030
Q201
Q202
SW201
SW202
SW203
SW204
SW205
SW206
Z4030
PCB
R201
R202
R203
R204
R205
R206
R207
R208
R209
R212
Z1020
YR010
YR040
PART-CODE
HRFS750JBA
HRFS750JBA
HRFS750JBA
HRFS101JBA
HRFS101JBA
HRFS472JBA
HRFS101JBA
HRFS000JBA
HRFS000JBA
HRFS000JBA
HRFS101JBA
HRFS103JBA
HRFS101JBA
HRFS101JBA
HRFS101JBA
HRFS472JBA
HRFS391JBA
HRFS103JBA
HRFS472JBA
TAPM4835KC
1APL111725
9979300504
1CAT24WC08
1MST9011—
5XS12R000E
5XS14R318F
PCPLSWG190
9970790113
DSD50GYW—
9979220084
9979220084
PCPLJRG172
TZTC3198YTZTC3198Y5S50101Z10
5S50101Z10
5S50101Z10
5S50101Z10
5S50101Z10
5S50101Z10
PCPLJAG172
9979800614
RD-AZ302JRD-AZ682JRD-AZ153JRD-AZ303JRD-AZ623JRD-AZ221JRD-AZ472JRD-AZ221JRD-AZ472JRD-AZ101JPCBCCPG207
99721173A1
7173301212
PART-NAME
PART-DESC
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
R CHIP
FET
IC REGULATOR
SOCKET IC
IC EEPROM
IC LCD CONTROLLER
CRYSTAL QUARTZ
CRYSTAL QUARTZ
PCB CONTROL AS
CONN AS
LED
CONN WAFER
CONN WAFER
PCB CONTROL RAD.AS
TRANSISTOR
TRANSISTOR
SW TACT
SW TACT
SW TACT
SW TACT
SW TACT
SW TACT
PCB CONTROL AXIAL AS
PCB CONTROL
R CARBON FILM
R CARBON FILM
R CARBON FILM
R CARBON FILM
R CARBON FILM
R CARBON FILM
R CARBON FILM
R CARBON FILM
R CARBON FILM
R CARBON FILM
COVER REAR AS
COVER REAR AS
SCREW TAPPTITE
43
1/16 75 OHM J 1608
1/16 75 OHM J 1608
1/16 75 OHM J 1608
1/16 100 OHM J 1608
1/16 100 OHM J 1608
1/16 4.7K OHM J 1608
1/16 100 OHM J 1608
1/16 0 OHM J 1608
1/16 0 OHM J 1608
1/16 0 OHM J 1608
1/16 100 OHM J 1608
1/16 10K OHM J 1608
1/16 100 OHM J 1608
1/16 100 OHM J 1608
1/16 100 OHM J 1608
1/16 4.7K OHM J 1608
1/16 390 OHM J 1608
1/16 10K OHM J 1608
1/16 4.7K OHM J 1608
APM4835KC-TR
APL1117-25VC-TR
PLCC 1.27PT 44PIN(22*22)
CAT24WC08 J
MST9011
HC-49/SM5H 12MHZ 11PF
HC-49/SM5H 14.318MHZ 18PF
CML-523BMW-L
SMH200+YBNH200+1007#26/1354#28=350
SD50GYW(GREEN/AMBER)
SMAW200-03/68163-0310
SMAW200-03/68163-0310
CML-523BW-L
KTC3198Y-(1815Y) (AUTO)
KTC3198Y-(1815Y) (AUTO)
KPT-1115AM
KPT-1115AM
KPT-1115AM
KPT-1115AM
KPT-1115AM
KPT-1115AM
CML-523BW-L
CML-523B T=1.6*202*28
1/6 3K OHM J
1/6 6.8K OHM J
1/6 15K OHM J
1/6 30K OHM J
1/6 62K OHM J
1/6 220 OHM J
1/6 4.7K OHM J
1/6 220 OHM J
1/6 4.7K OHM J
1/6 100 OHM J
CML-523BM-4L
CML-520B C/REAR AS
TT2 BIN 3X12 MFZN BK
ELECTRICAL PARTS LIST
LOC
YR070
YR080
YR090
Z1030
YP010
YP020
YP030
YP040
YP050
YP051
YP060
YP061
YP063
YP064
YP065
YP100
YP110
YP120
YP130
PART-CODE
99729250A1
7173301012
7S103B4081
PCPKCPG205
9978051702
9978136300
9978215300
2TP00075CL
9975841000
9919310000
9978634606
W3415M7319970800072
9978212900
99708A0019
9975842900
9972610300
9975432903
9975841607
PART-NAME
PART-DESC
STAND AS
SCREW TAPTITE
SCREW SPECIAL
PACKING AS
BOX CARTON
CUSHION
BAG POLY
TAPE OPP
LABEL BARCODE
LABEL BARCODE E
MANUAL INSTRUCTION
CORD POWER
CABLE SIGNAL AS
BAG POLY
STEREO CABLE W/FERRITE CORE
STICKER CLEAR
HANDLE
LABEL RATING
LABEL I/O
44
CML-520B STAND AS
TT2 BIN 3X10 MFZN BK
M/C BIN 4*8 MFZN
CML-523BM-4L
523BM-L DTE FRANCE
E.P.S
PEHD T=0.5*550*700
50X75 CLEAR
ART PAPER 71*36
ART PAPER COM IMPRINTABLE
CML-523BM-L (DTE FRANCE EN/FR)
C5 H03VV-F 3X0.75 1.8M BK
15P+2C/DDC+GY-641A+OD5.5=1.5M
PE FILM T0.05*250*350
3.5ST/M-FRT+3.5ST/M
CLEAR 20 T0.1MM PET REMOVAL
66 SHEET
L523BM-4L (DTE FRANCE)
P.E T=0.1*191*7 (L523BM)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising