Chauvet | Intimidator COLOR LED | User manual | Chauvet Intimidator COLOR LED User manual

Chauvet Intimidator COLOR LED User manual
User Manual
TABLE OF CONTENTS
1. Before You Begin .......................................................................................................... 3
What Is Included ............................................................................................................................... 3
Unpacking Instructions ..................................................................................................................... 3
Claims ....................................................................................................................................................... 3
Text Conventions ............................................................................................................................. 3
Symbols ............................................................................................................................................ 3
Disclaimer ......................................................................................................................................... 3
Product at a Glance .......................................................................................................................... 4
Safety Notes ..................................................................................................................................... 4
2. Introduction ................................................................................................................... 5
Overview........................................................................................................................................... 5
Dimensions ....................................................................................................................................... 6
3. Setup .............................................................................................................................. 7
AC Power ......................................................................................................................................... 7
Fuse Replacement .................................................................................................................................... 7
Power Linking ............................................................................................................................................ 8
Mounting ........................................................................................................................................... 9
Orientation ................................................................................................................................................. 9
Rigging ...................................................................................................................................................... 9
4. Operation ......................................................................................................................10
Control Panel Operation ................................................................................................................. 10
Menu Map....................................................................................................................................... 10
Configuration (DMX) ....................................................................................................................... 10
Starting Address ...................................................................................................................................... 11
DMX Values.................................................................................................................................... 11
8-CH ........................................................................................................................................................ 11
14-CH ...................................................................................................................................................... 12
Configuration (Standalone) ............................................................................................................ 15
Sound-Active Mode ................................................................................................................................. 15
Automatic Mode....................................................................................................................................... 15
Manual Pan/Tilt Operation ....................................................................................................................... 15
Pan/Tilt Angle Range............................................................................................................................... 15
Display ..................................................................................................................................................... 16
Master/Slave Mode .................................................................................................................................. 16
Movement Speed .................................................................................................................................... 16
Reset Software ........................................................................................................................................ 16
5. Technical Information ..................................................................................................17
Product Maintenance ..................................................................................................................... 17
6. Technical Specifications..............................................................................................18
Returns ........................................................................................................................................... 19
Contact Us ........................................................................................................................19
Page 2 of 19
Intimidator™ Beam LED 350 User Manual Rev. 3
1. BEFORE YOU BEGIN
What Is
Included
·
·
Intimidator™ Beam LED 350
Hanging bracket with mounting
hardware
·
·
·
Power cord
Warranty card
Quick Reference Guide
Unpacking
Instructions
Carefully unpack the product immediately and check the container to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not CHAUVET®.
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of delivery.
Text
Conventions
Symbols
Convention
1—512
50/60
Settings
Menu > Settings
<ENTER>
ON
Symbol
Meaning
A range of values
A set of values of which only one can be chosen
A menu option not to be modified
A sequence of menu options to be followed
A key to be pressed on the product’s control panel
A value to be entered or selected
Meaning
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this User Manual are subject to change
without notice. CHAUVET® assumes no responsibility or liability for any errors or
omissions, and reserves the right to revise or recreate this manual at any time.
Download the latest version from www.chauvetlighting.com.
© Copyright 2014 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Author
Date
Editor
Date
A. Leon
02/10/14
D. Couppe
02/19/14
Intimidator™ Beam LED 350 User Manual Rev. 3
Page 3 of 19
Product at a
Glance
Use on Dimmer
Outdoor Use
Sound-Activated
DMX
Master/Slave
Safety Notes
Auto Programs
Auto-ranging Power Supply
Replaceable Fuse
User-Serviceable
P
P
P
x
These notes include important information about the mounting, usage, and maintenance
of this product; read before using the product.
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Page 4 of 19
x
x
P
P
P
This product is not intended for permanent installation.
Always connect the product to a grounded circuit to avoid the risk of electrocution.
Always disconnect the product from the power source before cleaning or replacing
the fuse.
Avoid direct eye exposure to the light source while the product is on.
Make sure the power cord is not crimped or damaged.
Never disconnect the product from power by pulling or tugging on the cord.
If mounting the product overhead, always secure to a fastening device using a
safety cable.
Make sure there are no flammable materials close to the product when operating.
Do not touch the product’s housing when operating because it may be very hot.
Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
Always mount this product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
Be sure that no ventilation slots on the product’s housing are blocked.
Never connect the product to a dimmer.
Make sure to replace the fuse with another of the same type and rating.
Never carry the product from the power cord or any moving part. Always use the
handles.
The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the
product at higher temperatures.
In the event of a serious operating problem, stop using the product immediately.
Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Contact the nearest authorized technical assistance center.
This product is not intended for permanent installation.
Keep this User Manual for future use. If you sell the product to another user, be
sure to give this document to the next owner.
Intimidator™ Beam LED 350 User Manual Rev. 3
2. INTRODUCTION
Overview
Power In
Fuse Holder
DMX In/Out
Power Out
Safety Loop
Intimidator™ Beam LED 350 User Manual Rev. 3
LED Display
Page 5 of 19
Dimensions
18.5 in
(470 mm)
Page 6 of 19
Intimidator™ Beam LED 350 User Manual Rev. 3
3. SETUP
AC Power
The Intimidator™ Beam LED 350 has an auto-ranging power supply and it can work with
an input voltage range of 100–240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product’s back panel, or
refer to the product’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a protected circuit (circuit breaker or fuse). Make
sure the product has an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0–100% switch.
Fuse
Replacement
Disconnect the product from power before replacing the fuse.
1.
2.
3.
4.
5.
Disconnect the product from power.
Using a flat-head screwdriver, loosen the fuse holder and pull straight out.
Remove the blown fuse from the holder.
Replace with a fuse of the exact same type and rating.
Insert the fuse holder back in place and reconnect power.
A spare fuse is not included.
Always replace a blown fuse with the same type and rating.
Intimidator™ Beam LED 350 User Manual Rev. 3
Page 7 of 19
Power Linking
The product provides power linking via the Edison/IEC outlet located in the back of the
unit.
st
1 Product
Power Linking
Diagram
nd
2 Product
rd
3 Product
Other Products
You can power link up to 3 Intimidator™ Beam LED 350 units on 120 VAC or up to
7 Intimidator™ Beam LED 350 units on 230 VAC.
The power linking diagram shown above corresponds to the North American
version of the product ONLY! If using the product in other markets, you must
consult with the local CHAUVET® distributor as power linking connectors and
requirements may differ in your country or region.
Page 8 of 19
Intimidator™ Beam LED 350 User Manual Rev. 3
Mounting
Before mounting the product, read and follow the safety recommendations
indicated in the Safety Notes. For the CHAUVET® line of mounting clamps,
go to www.chauvetlighting.com/cables-clamps-main.html/.
Orientation
The Intimidator™ Beam LED 350 may be mounted in any position; however, make sure
adequate ventilation is provided around the product.
Rigging
·
Before deciding on a location, always make sure there is easy access to the product
for maintenance and programming.
·
Make sure that the structure or surface onto which you are mounting the product
can support the product’s weight (see the Technical Specifications).
·
When mounting the product overhead, always use a safety cable (such as CH-05
from CHAUVET®). Mount the product securely to a rigging point, such as an
elevated platform or a truss.
·
When rigging the product onto a truss, you should use mounting clamps (such as
CLP-15 from CHAUVET®) of appropriate weight capacity.
·
When power linking multiple products, you must always consider the length of the
power linking cable and mount the products close enough for the cable to reach.
·
The rubber feet also serve as floor supports. When mounting the product on the
floor, make sure that the product and cables are away from people and vehicles.
Bracket Attachment
Mounting Diagram
Rubber Feet (x4)
Safety Loop Attachment Point
When using only one mounting clamp with this fixture, you must use a
clamp with a captive bolt to prevent accidental loosening.
Intimidator™ Beam LED 350 User Manual Rev. 3
Page 9 of 19
4. OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the
display.
Button
<MODE/ESC>
<UP>
Menu Map
Scrolls up the list of options or selects a higher value
Scrolls down the list of options or selects a lower value
<ENTER>
Activates a menu option or a selected value
Main Level
Operation Modes
Pan
Tilt
Display
Channel Mode
Pan Range
Tilt Range
Reset
Load
Movement Speed
Page 10 of 19
Selects an operation mode or backs out of the current menu option
<DOWN>
DMX Address
Configuration
(DMX)
Function
Programming Levels
d001–d512
SLAv (Son)
nASL (SLoU)
nAFA (FASt)
nStS (SrUn)
Normal Pan
PAn
Inverse Pan
rPAn
Normal Tilt
tit
Inverse Tilt
rtit
Normal
diS
Display
Inverse
rdiS
Display
14-Channel
14CH
Mode
8-Channel
8CH
Mode
Pan 540°
PA54
Pan 360°
PA36
Pan 180°
PA18
Tilt 270°
ti27
Tilt 180°
ti18
Tilt 90°
ti 9
rESt
LoAd
inS
nOUS
dES
Description
Sets the DMX starting address
Slave operating mode
Automatic mode, slow program
Automatic mode, fast program
Sound-Active mode
Normal pan operation
Inverse pan operation
Normal tilt operation
Inverse tilt operation
Changes the LCD display text position
Selects the DMX personality
Selects pan range
Selects tilt range
Resets fixture
Loads factory defaults
Increasing speed
Decreasing speed
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
Intimidator™ Beam LED 350 User Manual Rev. 3
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
The Intimidator™ Beam LED 350 uses up to 14 DMX channels in 14-CH DMX mode,
which defines the highest configurable address to 499.
If unfamiliar with DMX, download the DMX Primer from www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MODE/ESC> repeatedly until d001 shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.
DMX Values
8-CH
Channel Function
1
2
Pan
Tilt
3
Color Wheel
4
Gobo Wheel
Intimidator™ Beam LED 350 User Manual Rev. 3
Value
Setting
000 ó 255
000 ó 255
000 ó 006
007 ó 013
014 ó 020
021 ó 027
028 ó 034
035 ó 041
042 ó 048
049 ó 055
056 ó 063
064 ó 070
071 ó 077
078 ó 084
085 ó 091
092 ó 098
099 ó 105
106 ó 112
113 ó 119
120 ó 127
128 ó 191
192 ó 255
0–540°
0–270°
White
Yellow
Pink
Green
Red
Light Blue
Kelly Green
Orange
Dark Blue
White + Yellow
Yellow + Pink
Pink + Green
Green + Red
Red + Light Blue
Light Blue + Kelly Green
Kelly Green + Orange
Orange + Dark Blue
Dark Blue + White
Color cycling rainbow with increasing speed
Reverse color cycling rainbow with increasing speed
000 ó 047
048 ó 063
064 ó 079
080 ó 087
088 ó 095
096 ó 103
104 ó 111
112 ó 119
120 ó 127
128 ó 191
192 ó 255
Gobos 1–5 plus open
Animation effect (static)
Animation speed (slow to fast)
Gobo 5 shake, from slow to fast
Gobo 4 shake, from slow to fast
Gobo 3 shake, from slow to fast
Gobo 2 shake, from slow to fast
Gobo 1 shake, from slow to fast
Open
Cycle effect with increasing speed
Reverse cycling effect with increasing speed
Page 11 of 19
8-CH (cont.)
14-CH
Page 12 of 19
Channel Function
5
No Function
6
Prism/Frost
7
No Function
8
Shutter
Channel Function
1
2
3
4
5
Pan
Fine Pan
Tilt
Fine Tilt
Speed
6
Color Wheel
Value
000 ó 255
000 ó 007
008 ó 012
013 ó 130
131 ó 247
248 ó 255
000 ó 255
000 ó 003
004 ó 007
008 ó 076
077 ó 145
146 ó 215
216 ó 255
Value
Setting
No function
Open
Prism on
Prism rotation with increasing speed
Reverse prism rotation with increasing speed
Frost effect
No function
Closed
Open
Strobe effect with increasing speed
Pulse strobe
Random shutter
Open
Setting
000 ó 255
000 ó 255
000 ó 255
000 ó 255
000 ó 255
000 ó 006
007 ó 013
014 ó 020
021 ó 027
028 ó 034
035 ó 041
042 ó 048
049 ó 055
056 ó 063
064 ó 070
071 ó 077
078 ó 084
085 ó 091
092 ó 098
099 ó 105
106 ó 112
113 ó 119
120 ó 127
128 ó 191
0–540°
Fine panning control
0–270°
Fine tilting control
Pan/Tilt speed (fast to slow)
White
Yellow
Pink
Green
Red
Light Blue
Kelly Green
Orange
Dark Blue
White + Yellow
Yellow + Pink
Pink + Green
Green + Red
Red + Light Blue
Light Blue + Kelly Green
Kelly Green + Orange
Orange + Dark Blue
Dark Blue + White
Color cycling rainbow with increasing speed
Reverse color cycling rainbow with increasing
192 ó 255
speed
Intimidator™ Beam LED 350 User Manual Rev. 3
14-CH
(cont.)
Channel Function
7
Gobo Wheel
8
No Function
9
Prism/Frost
10
11
No Function
Dimmer
Intimidator™ Beam LED 350 User Manual Rev. 3
Value
000 ó 047
048 ó 063
064 ó 079
080 ó 087
088 ó 095
096 ó 103
104 ó 111
112 ó 119
120 ó 127
128 ó 191
192 ó 255
000 ó 255
000 ó 007
008 ó 012
013 ó 130
131 ó 247
248 ó 255
000 ó 255
000 ó 255
Setting
Gobos 1–5 plus open
Animation effect (static)
Animation speed (slow to fast)
Gobo 5 shake, from slow to fast
Gobo 4 shake, from slow to fast
Gobo 3 shake, from slow to fast
Gobo 2 shake, from slow to fast
Gobo 1 shake, from slow to fast
Open
Cycle effect with increasing speed
Reverse cycle effect with increasing speed
No function
Open
Prism on
Prism rotation with increasing speed
Reverse prism rotation with increasing speed
Frost effect
No function
0–100%
Page 13 of 19
14-CH
(cont.)
Channel Function
12
Shutter
Value
000 ó 003
004 ó 007
008 ó 076
077 ó 145
146 ó 215
216 ó 255
000 ó 007
008 ó 015
016 ó 023
024 ó 031
032 ó 039
040 ó 047
Page 14 of 19
13
Control Functions
14
Auto Programs
048 ó 055
056 ó 095
096 ó 103
104 ó 111
112 ó 119
120 ó 127
128 ó 135
136 ó 143
144 ó 151
152 ó 159
160 ó 255
000 ó 007
008 ó 023
024 ó 039
040 ó 055
056 ó 071
072 ó 087
088 ó 103
104 ó 119
120 ó 135
136 ó 151
152 ó 167
168 ó 183
184 ó 199
200 ó 215
216 ó 231
232 ó 247
248 ó 255
Percent/Setting
Closed
Open
Strobe effect with increasing speed
Pulse strobe
Random shutter
Open
No function
Blackout while pan/tilt moving
Blackout while moving color wheel
Blackout while moving gobo wheel
Disable blackout while pan/tilt/moving color
wheel
Disable blackout while pan/tilt/moving gobo
wheel
Disable blackout while moving all options
No function
Reset pan
Reset tilt
Reset color wheel
Reset gobo wheel
No function
Reset prism
No function
Reset all channels
No function
No function
Auto program 1
Auto program 2
Auto program 3
Auto program 4
Auto program 5
Auto program 6
Auto program 7
Auto program 8
Sound-controlled program 1
Sound-controlled program 2
Sound-controlled program 3
Sound-controlled program 4
Sound-controlled program 5
Sound-controlled program 6
Sound-controlled program 7
Sound-controlled program 8
Intimidator™ Beam LED 350 User Manual Rev. 3
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
Never connect a product that is operating in any standalone mode (either
Automatic, or Sound-Active) to a DMX string connected to a DMX controller.
Products in standalone mode may transmit DMX signals that could interfere with
the DMX signals from the controller.
Sound-Active
Mode
To enable the Sound-Active mode, do the following:
1. Press <MODE/ESC> repeatedly until one of the following shows on the display:
nASL, nAFA, nStS, SLAv
2. Press <UP> or <DOWN> to select NStS.
3. Press <ENTER> and SrUn shows on the display.
4.
Turn the music on.
The product will only respond to low frequencies of music (bass and drums).
Automatic Mode
Manual Pan/Tilt
Operation
To enable the Automatic mode, do the following:
1. Press <MODE/ESC> repeatedly until one of the following shows on the display:
nASL, nAFA, nStS, SLAv
2. Press <UP> or <DOWN> to select nASL (for a slow program) or nAFA (for a fast
program).
3. Press <ENTER> and SLoU displays while in slow program or FASt displays while
in fast program.
To select either normal panning or inverted panning, do the following:
1. Press <MODE/ESC> repeatedly until PAn or rPAn shows on the display.
2. Press <UP> or <DOWN> to select PAn (normal pan operation) or rPAn (inverse
pan operation).
3. Press <ENTER>.
To select either normal tilting or inverted tilting, do the following:
1. Press <MODE/ESC> repeatedly until tit shows on the display.
2. Press <UP> or <DOWN> to select tit (normal tilt operation) or rtit (inverse tilt
operation).
3. Press <ENTER>.
Pan/Tilt Angle
Range
To select which pan angle to use:
1. Press <MODE/ESC> repeatedly until PA54, PA36, or PA18 shows on the display.
2. Press <UP> or <DOWN> to select PA54 (540°), PA36 (360°), or PA18 (180°).
3. Press <ENTER>.
To select which tilt angle to use:
1. Press <MODE/ESC> repeatedly until ti27, ti18, or ti 9 shows on the display.
2. Press <UP> or <DOWN> to select ti27 (270°), ti18 (180°), or ti 9 (90°).
3. Press <ENTER>.
Intimidator™ Beam LED 350 User Manual Rev. 3
Page 15 of 19
Display
Master/Slave
Mode
To flip the LED display for better readability in any mounting situation, do the following:
1. Press <MODE/ESC> repeatedly until diS or rdiS shows on the display.
2. Press <UP> or <DOWN> to select diS (normal display mode) or rdiS (inverse
display mode).
3. Press <ENTER>.
The Master/Slave mode allows a single Intimidator™ Beam LED 350 unit (the master) to
control the actions of one or more Intimidator™ Beam LED 350 units (the slaves) without
the need of a DMX controller. The master unit will be set to operate in either Automatic
or Sound-Active mode, while the slave units will be set to operate in Slave mode. Once
set and connected, the slave units will operate in unison with the master unit.
Configure the units as indicated below.
Slave units:
1. Press <MODE/ESC> repeatedly until one of the following shows on the display:
nASL, nAFA, nStS, SLAv
2. Press <UP> or <DOWN> to select SLAv.
3. Press <ENTER> to accept and Son shows on the display.
4. Set the DMX address to d001.
5.
6.
Connect the DMX input of the first slave unit to the DMX output of the master unit.
Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
7. Finish setting and connecting all the slave units.
Master unit:
1.
2.
Movement Speed
Reset Software
Page 16 of 19
Set the master unit to operate in either Automatic or Sound-Active mode.
Make the master unit the first unit in the DMX daisy chain.
To increase or decrease movement speed, do the following.
1. Press <MODE/ESC> repeatedly until nouS shows on the display.
2. Press <ENTER> and inS or dES shows on the display.
3. Press <UP> or <DOWN> to select inS (increasing speed) or dES (decreasing
speed).
4. Press <ENTER>.
·
Configure all the slave units before connecting the master unit to the DMX
daisy chain.
·
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller may interfere with the signals from the
master unit.
·
Do not connect more than 31 slave units to the master unit.
·
The Intimidator™ Beam LED 350 can be connected in Master/Slave with the
Intimidator™ Spot LED 350, but the Intimidator™ Beam LED 350 must be set to
Automatic mode’s slow program for the products to sync correctly.
·
Do not change the Movement Speed on the Intimidator™ Beam LED 350 while
the product is in motion. Stop the product before changing speeds.
To reset the software, do the following:
1. Press <MODE/ESC> repeatedly until rESt shows on the display.
2. Press <ENTER>. The product will reset all settings in the software to the default
factory settings.
Intimidator™ Beam LED 350 User Manual Rev. 3
5. TECHNICAL INFORMATION
Product
Maintenance
Dust build-up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life and mechanical wear. To maintain optimum
performance and minimize wear, clean the product at least twice a month. However,
usage and environmental conditions contribute to increased cleaning frequency.
To clean the product, follow the instructions below:
·
Unplug the product from power.
·
Wait until the product is at room temperature.
·
Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents.
·
Clean all glass/transparent surfaces with a mild soap solution, ammonia-free glass
cleaner, or isopropyl alcohol.
·
Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
·
Softly wipe any dirt or grime to the outside edges of the glass/transparent surface.
·
Gently polish the glass/transparent surfaces until they are free of haze and lint.
Always dry the glass/transparent surfaces carefully after cleaning them.
Do not spin the cooling fan using compressed air because you could damage it.
Intimidator™ Beam LED 350 User Manual Rev. 3
Page 17 of 19
6. TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
11.3 in (287 mm)
13.4 in (340 mm)
18.5 in (470 mm)
22 lb (9.8 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Light Source
Photo Optic
Thermal
DMX
Ordering
Page 18 of 19
Power Supply Type
Range
Voltage Selection
Switching (internal)
100–240 VAC, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
258 W
269 W
Operating current
2.1 A
1.2 A
Power linking current (units)
15 A (3 units)
15 A (7 units)
Fuse
F 3 A, 250 V
F 3 A, 250 V
Power I/O
US/Canada
UK/Worldwide
IEC
Power input connector
IEC
Power output connector
Edison
IEC
Power cord plug
Edison (US)
Local plug
Type
Power
Lifespan
LED
75 W
50,000 hours
Color
Quantity
Current
White
1
17 A
Parameter
Illuminance @ 2 m
139,200 lux
Beam angle
4°
Strobe rate
0 to 20 Hz
Pan and Tilt
540° pan
270° tilt
Pan/Tilt ranges
540°, 360°, 180° pan
270°, 180°, 90° tilt
Maximum External Temp.
Cooling System
104 °F (40 °C)
Fan-cooled
I/O Connectors
Connector Type
Channel Range
3-pin XLR
XLR
8, 14
Product Name
Item Code
UPC Number
Intimidator™ Beam LED 350
08010569
781462209179
Intimidator™ Beam LED 350 User Manual Rev. 3
To return a product or request support:
·
·
·
·
In the U.S., contact CHAUVET® World Headquarters.
In the UK or Ireland, contact CHAUVET® Europe Ltd.
In Mexico, contact CHAUVET® Mexico.
In any other country, DO NOT contact CHAUVET®. Contact your distributor.
If you live outside the U.S., United Kingdom, Ireland, or Mexico, contact your distributor of record
and follow their instructions on how to return CHAUVET® products to them. Visit our website for
contact details.
Returns
Call the corresponding CHAUVET® Technical Support office and request a Return Merchandise
Authorization (RMA) number before shipping the product. Be prepared to provide the model number, serial
number, and a brief description of the cause for the return.
You must send the merchandise prepaid, in its original box, and with its original packing and accessories.
CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any product returned without an
RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number directly on the
box.
Before sending the product, clearly write the following information on a piece of paper and place it inside
the box:
·
Your name
·
Your address
·
Your phone number
·
RMA number
·
A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be
your responsibility. FedEx packing or double-boxing are recommended.
CHAUVET® reserves the right to use its own discretion to repair or replace returned product(s).
CONTACT US
WORLD HEADQUARTERS - CHAUVET®
General Information
Technical Support
Address:5200 NW 108th Avenue
Voice: (954) 577-4455 (Press 4)
Sunrise, FL 33351
Fax:
(954) 756-8015
Voice: (954) 577-4455
Email: tech@chauvetlighting.com
Fax:
(954) 929-5560
World Wide Web www.chauvetlighting.com
Toll free: (800) 762-1084
UNITED KINGDOM AND IRELAND - CHAUVET® Europe Ltd.
General Information
Technical Support
Address:Unit 1C
Email: uktech@chauvetlighting.com
Brookhill Road Industrial Estate
World Wide Web www.chauvetlighting.co.uk
Pinxton, Nottingham, UK
NG16 6NT
Voice: +44 (0)1773 511115
Fax:
+44 (0)1773 511110
MEXICO - CHAUVET® Mexico
General Information
Technical Support
Address:Av. Santa Ana 30
Email: servicio@chauvet.com.mx
Parque Industrial Lerma
World Wide Web www.chauvet.com.mx
Lerma, Mexico C.P. 52000
Voice: +52 (728) 285-5000
Outside the U.S., United Kingdom, Ireland, or Mexico, contact your dealer. Follow their instructions to request support or
to return a product. Visit our website for contact details.
Intimidator™ Beam LED 350 User Manual Rev. 3
Page 19 of 19
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising