Associated Equipment 9409 Instruction manual
LTC 9409 Series
Instruction Manual
EN Weatherproof Outdoor
Pan/Tilts
LTC 9409 Series | Instruction Manual | Important Safeguards
EN | 2
Important Safeguards
1. Read, Follow, and Retain Instructions - All safety
and operating instructions should be read and
followed before operating the unit. Retain instructions
for future reference.
2. Heed Warnings - Adhere to all warnings on the unit
and in the operating instructions.
3. Attachments - Attachments not recommended by
the product manufacturer should not be used, as they
may cause hazards.
4. Installation Cautions - Do not place this unit on an
unstable stand, tripod, bracket, or mount. The unit
may fall, causing serious injury to a person and
serious damage to the unit. Use only manufacturerrecommended accessories, or those sold with the
product. Mount the unit per the manufacturer's
instructions. Appliance and cart combination should
be moved with care. Quick stops, excessive force, or
uneven surfaces may cause the appliance and cart
combination to overturn.
5. Cleaning - Unplug the unit from the outlet before
cleaning. Follow any instructions provided with the
unit. Generally, using a damp cloth for cleaning is
sufficient. Do not use liquid cleaners or aerosol
cleaners.
6. Servicing - Do not attempt to service this unit
yourself. Opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
7. Damage Requiring Service - Unplug the unit from
the main AC power source and refer servicing to
qualified service personnel under the following
conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled or an object has fallen
into the unit.
• If the unit has been exposed to water and/or
inclement weather (rain, snow, etc.).
• If the unit does not operate normally, when
following the operating instructions. Adjust only
those controls specified in the operating
instructions. Improper adjustment of other controls
may result in damage, and require extensive work
by a qualified technician to restore the unit to
normal operation.
• If the unit has been dropped or the cabinet
damaged.
• If the unit exhibits a distinct change in
performance, this indicates that service is needed.
8. Replacement Parts - When replacement parts are
required, the service technician should use
replacement parts specified by the manufacturer or
that have the same characteristics as the original part.
Unauthorized substitutions may result in fire,
electrical shock or other hazards.
9. Safety Check - Upon completion of servicing or
repairs to the unit, ask the service technician to
perform safety checks to ensure proper operating
condition.
Bosch Security Systems | 13 April 2004
10. Power Sources - Operate the unit only from the type
of power source indicated on the label. If unsure of
the type of power supply to use, contact your dealer
or local power company.
• For units intended to operate from battery power,
refer to the operating instructions.
• For units intended to operate with External Power
Supplies, use only the recommended approved
power supplies.
• For units intended to operate with a limited power
source, this power source must comply with
EN60950. Substitutions may damage the unit or
cause fire or shock.
• For units intended to operate at 24VAC, normal
input voltage is 24VAC. Voltage applied to the
unit's power input should not exceed 30VAC.
User-supplied wiring, from the 24VAC supply to
unit, must be in compliance with electrical codes
(Class 2 power levels). Do not ground the 24VAC
supply at the terminals or at the unit's power
supply terminals.
11. Coax Grounding - If an outside cable system is
connected to the unit, ensure that the cable system is
grounded. U.S.A. models only - Section 810 of the
National Electrical Code, ANSI/NFPA No.70,
provides information regarding proper grounding of
the mount and supporting structure, grounding of the
coax to a discharge unit, size of grounding
conductors, location of discharge unit, connection to
grounding electrodes, and requirements for the
grounding electrode.
12. Grounding or Polarization - This unit may be
equipped with a polarized alternating current line
plug (a plug with one blade wider than the other).
This safety feature allows the plug to fit into the
power outlet in only one way. If unable to insert the
plug fully into the outlet, try reversing the plug. If the
plug still fails to fit, contact an electrician to arrange
replacement of the obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
Alternately, this unit may be equipped with a
3-wire grounding plug (a plug with a third pin, for
grounding). This safety feature allows the plug to fit
into a grounding power outlet only. If unable to insert
the plug into the outlet, contact an electrician to
arrange replacement of the obsolete outlet. Do not
defeat the safety purpose of the grounding plug.
13. Lightning - For added protection during a lightning
storm, or when this unit is left unattended and
unused for long periods of time, unplug the unit from
the wall outlet and disconnect the cable system. This
will prevent damage to the unit due to lightning and
power line surges.
EN | 3
LTC 9409 Series | Instruction Manual | Important Safeguards
For Indoor Product
1. Water and Moisture - Do not use this unit near
water - for example, in a wet basement, in an
unprotected outdoor installation or in any area
classified as a wet location.
2. Object and Liquid Entry - Never push objects of
any kind into this unit through openings, as they
may touch dangerous voltage points or short out
parts that could result in a fire or electrical shock.
Never spill liquid of any kind on the unit.
3. Power Cord and Power Cord Protection - For
units intended to operate with 230VAC, 50Hz,
the input and output power cord must comply
with the latest versions of IEC Publication 227 or
IEC Publication 245.
Power supply cords should be routed so they are
not likely to be walked on or pinched. Pay
particular attention to location of cords and plugs,
convenience receptacles, and the point of exit
from the appliance.
4. Overloading - Do not overload outlets and
extension cords; this can result in a risk of fire or
electrical shock.
For Outdoor Product
Power Lines - An outdoor system should not be
located in the vicinity of overhead power lines,
electric lights or power circuits, or where it may
contact such power lines or circuits. When
installing an outdoor system, extreme care should
be taken to keep from touching power lines or
circuits, as this contact might be fatal. U.S.A.
models only - refer to the National Electrical
Code Article 820 regarding installation of CATV
systems.
For Rack-mount Product
1. Ventilation - This unit should not be placed in a
built-in installation or rack, unless proper
ventilation is provided, or the manufacturer’s
instructions have been adhered to. The
equipment must not exceed its maximum
operating temperature requirements.
2. Mechanical Loading - Mounting of the
equipment in a rack shall be such that a
hazardous condition is not achieved due to
uneven mechanical loading.
Bosch Security Systems | 13 April 2004
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC SENSITIVE
DEVICES
WARNING:
Electrostatic-sensitive device. Use
proper CMOS/MOSFET handling
precautions to avoid electrostatic
discharge.
NOTE: Grounded wrist straps must be worn and proper ESD
safety precautions observed when handling the electrostaticsensitive printed circuit boards.
Safety Precautions
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol indicates the presence of
uninsulated “dangerous voltage” within the
product’s enclosure. This may constitute a
risk of electric shock.
The user should consult the operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Attention: Installation should be performed by
qualified service personnel only in accordance
with the National Electrical Code or applicable
local codes.
Power Disconnect. Units with or without
ON-OFF switches have power supplied to the
unit whenever the power cord is inserted into the
power source; however, the unit is operational
only when the ON-OFF switch is in the ON
position. The power cord is the main power
disconnect for all units.
EN | 4
LTC 9409 Series | Instruction Manual | Important Safeguards
FCC & ICES INFORMATION
Sicherheitshinweise
(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1)
This device may not cause harmful interference, and
(2)
This device must accept any interference received,
including interference that may cause undesired
operation.
NOTE: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules and ICES-003 of Industry Canada. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses and radiates radio
frequency energy, and if not installed and used in accordance
with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at his
expense.
Intentional or unintentional changes or modifications, not
expressly approved by the party responsible for compliance, shall
not be made. Any such changes or modifications could void the
user’s authority to operate the equipment. If necessary, the user
should consult the dealer or an experienced radio/television
technician for corrective action. The user may find the following
booklet, prepared by the Federal Communications Commission,
helpful: How to Identify and Resolve Radio-TV Interference
Problems. This booklet is available from the U.S. Government
Printing Office, Washington, DC 20402, Stock No. 004-00000345-4.
WARNING: This is a Class A product. In a domestic
environment, this product may cause radio interference,
in which case, the user may be required to take adequate
measures.
VORSICHT: UM EINEN ELEKTRISCHEN SCHLAG ZU
VERMEIDEN, IST DIE ABDECKUNG (ODER RÜCKSEITE) NICHT
ZU ENTFERNEN. ES BEFINDEN SICH KEINE TEILE IN DIESEM
BEREICH, DIE VOM BENUTZER GEWARTET WERDEN
KÖNNEN. LASSEN SIE WARTUNGSARBEITEN NUR VON
QUALIFIZIERTEM WARTUNGSPERSONAL AUSFÜHREN.
Das Symbol macht auf nicht isolierte „gefährliche Spannung"
im Gehäuse aufmerksam. Dies kann zu einem elektrischen
Schlag führen.
Der Benutzer sollte sich ausführlich über Anweisungen für
die Bedienung und Instandhaltung (Wartung) in den
begleitenden Unterlagen informieren.
Achtung! Die Installation sollte nur von qualifiziertem
Kundendienstpersonal gemäß jeweils zutreffender
Elektrovorschriften ausgeführt werden.
Unterbrechung des Netzanschlusses. Geräte mit oder ohne
Netzschalter haben Spannung am Gerät anliegen, sobald der
Netzstecker in die Steckdose gesteckt wird. Das Gerät ist jedoch
nur betriebsbereit, wenn der Netzschalter (EIN/AUS) auf EIN
steht. Wenn das Netzkabel aus der Steckdose gezogen wird, ist
die Spannungszuführung zum Gerät vollkommen unterbrochen.
Precauciones de Seguridad
Sécurité
ATTENTION : POUR ÉVITER TOUT RISQUE D'ÉLECTROCUTION,
N'ESSAYEZ PAS DE RETIRER LE CAPOT (OU LE PANNEAU
ARRIÈRE). CET APPAREIL NE CONTIENT AUCUN COMPOSANT
SUSCEPTIBLE D'ÊTRE RÉPARÉ PAR L'UTILISATEUR. CONFIEZ
LA RÉPARATION DE L'APPAREIL À DU PERSONNEL QUALIFIÉ.
PRECAUCIÓN: PARA DISMINUIR EL RIESGO DE DESCARGA
ELÉCTRICA, NO RETIRE LA CUBIERTA (NI LA PARTE
POSTERIOR). NO EXISTEN PIEZAS DE RECAMBIO EN EL
INTERIOR DEL EQUIPO. EL PERSONAL DE SERVICIO
CUALIFICADO SE ENCARGA DE REALIZAR LAS
REPARACIONES.
Este símbolo indica que existen puntos de tensión peligrosos
sin aislamiento dentro de la cubierta de la unidad. Estos
puntos pueden constituir un riesgo de descarga eléctrica.
Ce symbole signale que le produit renferme une « tension
potentiellement dangereuse » non isolée susceptible de
provoquer une électrocution.
El usuario debe consultar las instrucciones de funcionamiento y
mantenimiento (reparación) en la documentación que se
suministra con el aparato.
Ce symbole invite l'utilisateur à consulter les instructions
d'utilisation et d'entretien (dépannage) reprises dans la
documentation qui accompagne l'appareil.
Atención: la instalación la debe realizar únicamente personal
cualificado de conformidad con el National Electric Code o las
normas aplicables en su país.
Attention : l'installation doit exclusivement être réalisée par du
personnel qualifié, conformément au code national d'électricité
américain (NEC) ou au code d'électricité local en vigueur.
Desconexión de la alimentación. Las unidades con o sin
interruptores de encendido/apagado reciben alimentación
eléctrica siempre que el cable de alimentación esté conectado a
la fuente de alimentación. Sin embargo, la unidad sólo funciona
cuando el interruptor está en la posición de encendido. El cable
de alimentación es la principal fuente de desconexión de todas
las unidades.
Coupure de l'alimentation. Qu'ils soient pourvus ou non d'un
commutateur ON/OFF, tous les appareils reçoivent de l'énergie une
fois le cordon branché sur la source d'alimentation. Toutefois,
l'appareil ne fonctionne réellement que lorsque
le commutateur est réglé sur ON. Le débranchement du cordon
d'alimentation permet de couper l'alimentation des appareils.
Bosch Security Systems | 13 April 2004
EN | 5
LTC 9409 Series | Instruction Manual | Importants Safeguards
Veiligheidsmaatregelen
VOORZICHTIG: OPEN DE BEHUIZING OF DE ACHTERKANT
VAN HET APPARAAT NIET. ZO VERMINDERT U HET RISICO
OP ELEKTRISCHE SCHOKKEN. IN HET APPARAAT
BEVINDEN ZICH GEEN ONDERDELEN DIE U ZELF KUNT
REPAREREN. LAAT SERVICE EN ONDERHOUD UITVOEREN
DOOR GEKWALIFICEERD PERSONEEL.
Medidas de Segurança
CUIDADO: PARA REDUZIR O RISCO DE CHOQUE
ELÉCTRICO, NÃO RETIRE A TAMPA (OU A PARTE
POSTERIOR). NO INTERIOR, NÃO EXISTEM PEÇAS QUE
POSSAM SER REPARADAS PELO UTILIZADOR. REMETA A
ASSISTÊNCIA PARA OS TÉCNICOS QUALIFICADOS.
Dit symbool geeft aan dat er binnen in het apparaat
ongeïsoleerde, gevaarlijke spanning aanwezig is die mogelijk
elektrische schokken kan veroorzaken.
Este símbolo indica a presença de "tensão perigosa" não isolada
dentro da estrutura do produto, o que pode constituir risco de
choque eléctrico.
De gebruiker dient de bedienings- en onderhoudsvoorschriften
te raadplegen in de documentatie die werd meegeleverd met
het apparaat.
O utilizador deve consultar as instruções de funcionamento
e manutenção (assistência) nos documentos que
acompanham o aparelho.
Attentie: het apparaat mag alleen door gekwalificeerd personeel
worden geïnstalleerd. De installatie dient in overeenstemming
met de nationale elektrische richtlijnen of de van toepassing
zijnde lokale richtlijnen te worden uitgevoerd.
Spanning uitschakelen. Apparatuur met of zonder
aan-uitschakelaar staat onder spanning zolang de stekker is
aangesloten op de wandcontactdoos. De apparatuur is uitsluitend
in werking als de aan-uitschakelaar aan staat. Het netsnoer is de
"hoofdschakelaar" voor alle apparatuur.
Sicurezza
ATTENZIONE: PER RIDURRE IL RISCHIO DI SCOSSE
ELETTRICHE NON RIMUOVERE LA COPERTURA (O IL
PANNELLO POSTERIORE). L'UNITÀ NON CONTIENE
COMPONENTI INTERNI RIPARABILI DALL'UTENTE. PER
QUALSIASI INTERVENTO, RIVOLGERSI A PERSONALE
TECNICO QUALIFICATO.
Questo simbolo indica la presenza di "tensione pericolosa" non
isolata all'interno del contenitore del prodotto. Ciò comporta un
potenziale rischio di scosse elettriche.
Si consiglia di consultare le istruzioni operative e di
manutenzione (interventi tecnici) contenute nella
documentazione fornita con il dispositivo.
Attenzione: l'installazione deve essere effettuata esclusivamente
da personale tecnico qualificato in conformità con il National
Electrical Code o con le normative locali vigenti.
Scollegamento dell'alimentazione. Le unità dotate o sprovviste di
interruttori ON-OFF vengono alimentate quando si inserisce il
cavo nella presa dell'alimentazione. L'unità è tuttavia in funzione
solo quando l'interruttore ON-OFF si trova nella posizione ON. Il
cavo di alimentazione costituisce il dispositivo di scollegamento
dell'alimentazione principale per tutte le unità.
Bosch Security Systems | 13 April 2004
Atenção: a instalação deve ser executada apenas por técnicos
qualificados da assistência, de acordo com o código eléctrico
nacional ou os códigos locais aplicáveis.
Corte de corrente. As unidades com ou sem interruptores
ON-OFF (ligar/desligar) recebem corrente sempre que o fio de
alimentação está introduzido na fonte de alimentação; contudo, a
unidade apenas está operacional quando o interruptor ON-OFF
está na posição ON. O fio de alimentação destina-se a desligar a
corrente em todas as unidades.
LTC 9409 Series | Instruction Manual | Table of Contents
EN | 6
Table of Contents
Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1
UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
3
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
4
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
4.1
Model Designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
4.2
Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
4.3
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
4.4
Grounding Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4.5
Connector Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4.6
Pan/Tilt Stops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
5
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
5.1
Manual Pan Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
5.2
Auto-pan Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
5.3
Pan Stop Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
5.4
Tilt Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
5.5
Pre-position Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
6
ILLUSTRATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Bosch Security Systems | 13 April 2004
EN | 7
LTC 9409 Series | Instruction Manual | Unpacking
1
UNPACKING
4
INSTALLATION
This electronic equipment should be unpacked and
handled with care.
This installation should be made by a qualified
service person, and conform to all local codes.
Check for the following items:
Always disconnect power to the unit at the
controller prior to connecting or disconnecting
pan/tilt electrical connector. Pan/tilt is to be
mounted away from unauthorized access
[3m (10ft) high minimum].
•
Model number of unit
If an item appears to have been damaged in shipment,
replace it properly in its carton and notify the shipper.
If any items are missing, notify your Bosch Security
Systems Inc. Sales Representative or Customer Service.
The LTC 9409 Series units are designed for
either upright or inverted installations. To
maintain weatherproof integrity when
mounting outdoors in an inverted position, the
unit must be installed in a weatherproof
enclosure (e.g., weatherproof domed housing)
or a protected outside area.
The shipping carton is the safest container in which
the unit may be transported. Save it for possible future
use.
2
SERVICE
If the unit ever needs repair service, the customer
should contact the nearest Bosch Security Systems Inc.
Service Center for authorization to return and shipping
instructions.
Service Centers
USA
Phone:
800-366-2283 or 717-735-6638
fax:
800-366-1329 or 717-735-6639
CCTV Spare Parts
Phone:
800-894-5215 or 408-956-3853 or 3854
fax:
408-957-3198
e-mail:
[email protected]
Canada
Phone:
514-738-2434
Europe, Middle East & Asia Pacific Region
Phone:
32-1-440-0711
For additional information, see
www.boschsecuritysystems.com.
3
Pan/tilts and associated equipment should be tested
prior to field installation to verify proper wiring and
operation of components.
The combined weight of the enclosure/camera/lens
should be centered equally, front to back, on the tilt
table surface for best pan/tilt operation.
4.1
Model
No. 1
Bosch Security Systems | 13 April 2004
Rated Motor
Voltage
Operational
Range
Total Pan Angle
(No fixed Stop)
LTC 9409/60
115VAC, 60Hz
103 to 126
150 to 3550
LTC 9409/20
24VAC, 60Hz
21.6 to 26.4
150 to 3550
LTC 9409/10
24VAC, 50Hz
21.6 to 26.4
150 to 3550
LTC 9409/502
230VAC, 50Hz
198 to 265
150 to 3550
LTC 9409/61
115VAC, 60Hz
103 to 126
150 to 3550
LTC 9409/21
24VAC, 60Hz
21.6 to 26.4
150 to 3550
LTC 9409/11
24VAC, 50Hz
21.6 to 26.4
150 to 3550
LTC 9409/51
230VAC, 50Hz
198 to 265
150 to 3550
Standard Models
Pre-position Models
DESCRIPTION
The LTC 9409 Series Weatherproof Outdoor Pan/Tilts
are low profile, economical, compact units constructed
with corrosion-resistant hardware. These remote
positioning devices are fully system compatible with
CCD cameras, lenses, and housing combinations.
Model Designation
1
The total power for all models, with both motors running, is 18W.
2
Single phase power sources only.
Do not exceed 30VAC on 24VAC models. Operation
above 30VAC violates low voltage operation (Class 2
Specifications). Normal operation is 24VAC.
EN | 8
LTC 9409 Series | Instruction Manual | Installation
4.1.1
Recommended Controls
LTC 5133 and
LTC 5134 Series
Desktop Pan/Tilt/Lens control
via hardwired connections
LTC 8561 and
LTC 8566 Series
Remote Receiver/Driver for a
balanced line system. For use
with LTC 8500 Series,
LTC 8600 Series, LTC 8800
Series, and LTC 5135 Series
Systems
4.3
Electrical Connections
1.
Cable must be wired according to Connector
Assembly and Recommended Maximum
Cable Lengths.
2.
Use separate shielded cables for camera power,
enclosure power, and pan/tilt control.
Combining lens control wiring and video coax
within a common cable is acceptable if
required. The use of a common multiconductor
cable to combine all functions is not
recommended. Using a shielded cable is
recommended for pre-position wiring.
3.
Use color-coded conductors to aid in wiring and
future identification.
4.
Retain the wiring diagram for later reference.
4.1.2 Recommended Mounting Equipment
LTC 9216/00
LTC 9222/00
LTC 9214/00
4.2
Medium duty wall mount, designed
to support up to 45.3kg (100lb)
Heavy duty wall mount, designed to
support up to 90.6kg (200lb)
Heavy duty column mount, for
ceiling or pedestal use
4.3.1 Recommended Maximum Cable Lengths
1
Model
Wire Size
Voltage
mm2
AWG
Meters
Feet
24VAC
0.5
20
58
190
1
18
91
300
1.5
16
145
475
2.5
14
236
775
4
12
381
1250
0.5
20
1402
4600
1
18
2256
7400
1.5
16
3537
11600
2.5
14
5762
18900
4
12
9146
30000
6
10
14146
46600
0.5
20
7622
25000
1
18
12043
39500
1.5
16
18172
59600
2.5
14
30701
100700
4
12
48872
160300
Wall Mounting
Follow the instructions provided with the mounts. The
mount and mounting surface must be able to support
the weight of the pan/tilt, camera/lens, and enclosure
(if used). The camera/lens/enclosure must be properly
mounted and balanced on the pan/tilt bracket.
CAUTION: The LTC 9409 Series pan/tilts are to be
mounted upright or inverted, never horizontally
115VAC
230VAC
Mount the camera/lens/enclosure to the pan/tilt
bracket as follows:
1.
Mount the camera/lens/enclosure, in either of
the two sets of slots. (Dome mounting: Use the
set of slots centered on the pan/tilt mounting
base.)
2.
Balance the camera/lens/enclosure on the
camera bracket, adjusting align with the
mounting holes. Fasten with a minimum of two
(2) 1/4-20 x 1/2-in. long fasteners and lock
washers.
3.
Make all electrical connections leaving sufficient
cable between camera/enclosure and pan/tilt to
allow for tilting and panning.
Bosch Security Systems | 13 April 2004
Distance
1
Values are calculated at 200C (680F) using stranded tinned copper wire, a
single conductor Pan/Tilt common (neutral) wire, and with both PAN and
TILT motors operating simultaneously.
EN | 9
LTC 9409 Series | Instruction Manual | Operation
4.4
Grounding Connection
Grounding is provided via pin 7 on the Power
Connector (P1). See Wiring Instructions and Wiring
Diagram.
4.5
Connector Assembly
Included with the unit are a mating connector and a
sealing boot or strain relief. Solder connections are
required. Make the electrical connection as shown in
Wiring Instructions.
The upper pan stop controls the pan left limit and the
lower pan stop controls the pan right limit. The left tilt
stop controls the tilt down limit, and the right tilt stop
controls the tilt up.
CAUTION: Disconnect P1 (Power Connector)
when making any adjustments to the pan or tilt
stops.
Tilt Down Limit Switch
Tilt Up Limit Stop
4.5.1 Wiring Instructions
Power Connector (P1)
Pin4
Connection2
1
Common (White)
2
Pan Left (CCW) (Black)
3
Pan Right (CW) (Brown)
4
Tilt up (Blue)
5
Tilt Down (Red)
6
NC1
7
Ground (Green/Yellow)
Pan Right Limit Stop
Pan Left Limit Stop
Power Connector (P2)3
Pin4
Connection2
1
PP supply (+5 VDC) (Orange)
2
Pan Position (Yellow)
3
PP Return (–5 VDC) (Green)
4
Tilt Position (Grey)
5
NC1
6
NC1
7
NC1
Notes:
W9412401AE
Figure 1 Pan and Tilt Stop Locations
5
5.1
OPERATION
Manual Pan Operation
The pan stops establish the limits for manual pan. The
maximum pan range is when the limit switches are
contacting each other.
1
NC – No Connection; do not use
2
Color codes indicate wiring harness colors inside the unit
3
P2 not found on non pre-position models
4
Pin numbers are molded into the connector
4.6
Pan/Tilt Stops
To access the pan and tilt stops, remove the rear cover
from the unit. Remove the cover by removing the four
Phillips head screws and pulling the cover outward.
The pan and tilt stops on this unit are hand-adjustable.
No tightening or loosening of fasteners (other than
cover removal) is required. The stops are located on
the gear motor output shafts near the printed circuit
boards. Adjustment of the stops can be made by handturning the stops or by using a small screw driver.
Bosch Security Systems | 13 April 2004
5.2
Auto-pan Operation
The auto-pan function requires connection of the unit
to a pan/tilt controller equipped with special current
sensing circuitry. Auto-pan is achieved by the
controller unit sensing changes in current flow through
the pan motor. When a stop is reached, current flow
stops, and the internal circuitry in the controller
reverses the auto-pan direction.
NOTE: The pan/tilt unit must be properly wired
for the function to operate correctly (see Wiring
Instructions).
EN | 10
LTC 9409 Series | Instruction Manual | Operation
5.3
Pan Stop Adjustment
1.
Adjust the pan/tilt unit into a direction
approximately in the center of the area to be
panned.
2.
Adjust the upper and lower pan stops until they
contact and are opposite the limit switches.
3.
Pan the unit left to the desired maximum
location. Adjust the upper pan stop CCW until
contact with the switch is made.
4.
Pan the unit right to the desired maximum
location. Adjust the lower pan stop CW until
contact with the switch is made.
5.
Operate the unit from the controller to confirm
that the limits are set properly. Readjust if
required.
5.4
Tilt Adjustments
1.
Adjust the tilt stops until both stops contact the
stop pin on the tilt gear motor output shaft.
2.
Tilt the unit down to the desired maximum
location. Adjust the left tilt stop CCW until
contact is made with the limit switch.
If the camera bracket blocks access to the opening at
both the up and down limit, contact Bosch Security
Systems Technical Support for futher instructions.
5.5
Pre-position Models
The models with pre-position capability (P suffix)
require connection of the Position Connector (P2) to a
controller or receiver/driver with the pre-position
function (see Wiring Instructions). Pan/tilt operation
and limit stop adjustment function as previously
described.
Upon installation, if the unit has an open circuit across
the pan potentiometer in the pan range (as measured
across P2, pins 1 and 2), the unit requires a
potentiometer Dead Zone adjustment, as follows
1.
Pan the unit to the left pan stop.
2.
Disconnect P1 and P2.
3.
Remove the rear cover and locate the pan
potentiometer. Loosen the nut on the underside
of the potentiometer support so the
potentiometer can be rotated.
4.
Locate the Dead Zone by rotating the
potentiometer CW or CCW and measuring the
resistance across P2, pin 1 and pin 2. The Dead
Zone is measured as an open circuit. Do not
rotate the potentiometer more than 1800 CW or
1800 CCW from the original position.
3.
Tilt the unit up to the desired maximum
location. Adjust the right tilt stop CW until
contact is made with the limit switch.
4.
Operate the unit from the controller to confirm
that the limits are set properly. Readjust if
required.
5.
NOTE: The camera mounting bracket may inhibit
access to the up tilt stop. Use the following
procedure to adjust the stop:
With the potentiometer in the Dead Zone, rotate
the potentiometer CW until a resistive value is
measured across P2, pins 1 and 2.
6.
Tighten the potentiometer nut. Replace the
cover and reconnect P1 and P2.
1.
Perform Steps 1 and 2 under Tilt Adjustments.
2.
Adjust the up tilt stop slightly to a location near
the desired stopping point.
3.
Tilt the unit up to the stop and observe the
results. Tilt the down.
4.
If a higher tilt stopping point is needed, adjust
the right tilt stop CCW. If a lower tilt stopping
point is needed, adjust the right tilt stop CW.
5.
Repeat Steps 3 and 4 until the desired location
is obtained.
Bosch Security Systems | 13 April 2004
EN | 11
LTC 9409 Series | Instruction Manual | Illustrations
6
ILLUSTRATIONS
25
1.0
ø 9.5 max.
ø 0.38 max.
5
0.2
5
0.2
To ensure water-tight seal,
hand-tighten connectors, +1/4 turn
mm
in
20
0.8
Figure 4 Connector Assembly
S 9506406B F
Pan Potentiometer
W9412402ae
Figure 2 Pan Potentiometer Location
76
3.0
169
6.6
Power
Connector
(P1)
7
0.28
+5 VDC
Pan Wiper
-5 VDC
Tilt Wiper
No Connection
No Connection
No Connection
P2-1
P2-2
P2-3
P2-4
P2-5
P2-6
P2-7
Black
Green
White
Green
P1
R2
1
Pan
Potentiometer
2
3
Positioning
Connector (P2)
(-P Units Only)
R1
PCB1 (PAN)
Blue
J3
19
0.75
P1-1
P1-2
P1-3
P1-4
P1-5
P1-6
P1-7
White
Black
Brown
Blue
Red
M1
1
J1
Common
Pan CCW
Pan CW
Tilt Up
Tilt Down
No Connection
Gnd
10
0.38
1
2
1
Blue
2
S1
2
3
3
Black
4
3
V1
Pan
Motor
Red
C1
S2
Grn/Yel
1
2
3
V2
67
2.6
P2
198
7.8
Tilt
Potentiometer
1
2
3
PCB2 (TILT)
Blue
J3
M2
1
J1
37
1.5
1
S1
1
Blue
2
2
3
2
3
4
149
5.9
Black
4
V1
Red
8
0.32
S2
1
2
4
V2
ø
121
4.75
W9412403BF
ø 102
4.00
mm
in
W9412400AE
Figure 3 Dimensional Outline
Bosch Security Systems | 13 April 2004
Figure 5 Wiring Diagram
Tilt
Motor
Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, PA 17601 USA
Tel: 800-326-3270
Fax: 1-717-735-6560
www.boschsecuritysystems.com
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven
The Netherlands
Tele +31 40 27 80000
© 2004 Bosch Security Systems GmbH
3935 890 07712 04-18 | April 29, 2004 | Data subject to change without notice.
Bosch Security Systems Pte Ltd.
38C Jalan Pemimpin
Singapore 577180
Republic of Singapore
Tel: 65 (6) 319 3486
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement