Merlin MT5580P Operating instructions

Merlin MT5580P Operating instructions
www.merlingo.com
profes
www.c
siona
hamb
l
erlain
anz.c
om
MT5580P
Sectional and Tilt Garage Door Opener
Installation and Operating Instructions
Owners Copy: Please keep these instructions for future reference
This manual contains IMPORTANT SAFETY information.
DO NOT PROCEED WITH THE INSTALLATION BEFORE READING THOROUGHLY.
N2966
START BY READING THESE IMPORTANT SAFETY INSTRUCTIONS
WARNING
• Failure to comply with the following instructions may result in serious personal injury or property damage.
• Read and follow all instructions carefully.
• The garage door opener is designed and tested to offer safe service provided it is installed and
operated in strict accordance with the instructions in this manual.
These safety alert symbols mean WARNING : A possible risk to personal safety or
property damage exists.
Keep garage door balanced. Do not let the
garage door opener compensate for a binding or
sticking garage door. Sticking, binding or unbalanced doors must be repaired before installing this
opener.
Do not wear rings, watches or loose clothing
while installing or servicing a garage door opener.
Frequently examine the door installation, in particular cable, springs and mountings for signs of
wear, damage or imbalance. Do not use if repair or
adjustment is needed since springs and hardware
are under extreme tension and a fault can cause
serious personal injury.
To avoid serious personal injury from entanglement, remove all ropes, chains and locks connected to the garage door before installing the
door opener.
Installation and wiring must be in compliance with
your local building and electrical codes.
The safety reverse system test is very important. Your garage door MUST reverse on contact
with a 40mm obstacle placed on the floor. Failure to
properly adjust the opener may result in serious
personal injury from a closing garage door. Repeat
the test once a month and make any necessary
adjustments.
This opener should not be installed in a damp
or wet space exposed to weather.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
The Protector SystemTM must be used for all
installations where the closing force as measured on the bottom of the door is over 400N
(40kgf). Excessive force will interfere with the
proper operation of the Safety Reverse System or
damage the garage door.
After installation, ensure that the parts of the
door do not extend over public footpaths or
roads.
Install the wireless wall control (or any additional
wall control) in a location where the garage
door is visible, at a height of at least 1.5m and
out of the reach of children. Do not allow children to operate push button(s) or transmitter(s). Serious personal injury from a closing
garage door may result from misuse of the opener.
Permanently fasten the Warning Labels in
Prominent Places, adjacent to Wall Controls and
manual release mechanisms as a reminder of
safe operating procedures.
Activate opener only when the door is in full
view, free of obstructions and the opener is
properly adjusted. No one should enter or
leave the garage while the door is in motion.
Do not allow children to play near the door, or
door controls.
Disconnect electric power to the garage door
opener before making repairs or removing
covers.
KEEP THESE INSTRUCTIONS
Warning: If your garage has no service entrance door, a CM1702 outside quick release must be installed.
This accessory allows manual operation of the garage door from outside in case of power failure.
CONTENTS
PAGE
SAFETY INSTRUCTIONS . . . . . . . .2
DOOR TYPES . . . . . . . . . . . . . . . . .3
TOOLS REQUIRED . . . . . . . . . . . .3
HARDWARE PROVIDED . . . . . . .3-4
BEFORE YOU BEGIN . . . . . . . . . . .5
COMPLETED INSTALLATION . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . .5-7
INSTALLATION . . . . . . . . . . . . .8-14
ADJUSTMENT . . . . . . . . . . . . . . . .14
SAFETY REVERSE SYSTEM . . . .15
2
INSTALL IR SAFETY BEAMS . . . .15
WIRED DOOR CONTROLS . . . . .16
WIRELESS PROGRAMMING . . . .17
SPECIAL FEATURES . . . . . . . . . .18
ACCESSORIES . . . . . . . . . . . . . . .19
SPECIFICATIONS & SAFETY . . .19
OPERATION OF YOUR OPENER 20
MAINTAINING YOUR OPENER . .20
CARE OF YOUR OPENER . . . . . .20
REPLACEMENT PARTS . . . . .21-22
TROUBLESHOOTING . . . . . . . . . 23
WARRANTY . . . . . . . . . . . . . . . . .24
1
DOOR TYPES
A. One-piece door with horizontal track only
B. Sectional door with curved track
A
C. One-piece door without track
To suit spring balanced doors up to 20m2
2
TOOLS REQUIRED
1
3
C
B
2
10mm, 8mm,
4.5mm, 4mm
HARDWARE PROVIDED
11mm, 13mm
1
a
2
b
c
3
4
7
5
6
11
8
9
NOTIC
E
15
12
16
10
17
14
3
13
4mm hex
head driver
Vibration Isolator:
(a) Vibration isolator (2)
(b) Lock washers (2)
(c) Nuts (2)
Chain Spreader Hardware:
(1) Hex Screws (2)
(2) Chain spreader (1)
(3) Flat washers (2)
Installation Hardware:
(4) Large clevis pin (1)
(5) Carriage bolts (2)
(6) Wood screws (4)
(7) Clevis pins (medium) (2)
(8) Hex screws (4)
(9) Rope
(10) Handle
(11) Lock washers (6)
(12) Nuts (6)
(13) 4mm anchors (2)
(14) R-Clip (3)
(15) 8mm anchors (4)
(16) Sheet metal screw (4)
(17) Machine screw (2)
4
HARDWARE PROVIDED
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
MT5580 opener
Angled door arm
Door mounting bracket
Straight door arm
Header bracket
Stop collar, nut & bolt
Pole kit adaptor
Trolley assembly
Idler pulley assembly
Chain and joiner
1
3
2
6
5
7
POLE OPTIONS
4
9
Pole Adaptor Kit
(11) 2.75m segmented pole kit
NOT PICTURED
3m one piece pole
8
10
3m Chain Pack and Joiner
Optional accessory
2.75m Segmented pole pack
(separate carton)
11
4
5
BEFORE YOU BEGIN
6
COMPLETED INSTALLATION (TILT DOOR EXAMPLE SHOWN)
1. Look at the wall or ceiling above the garage door. The header bracket must be securely fastened to structural
supports.
2. Do you have a finished ceiling in your garage? If so, a support bracket and additional fastening hardware
(not supplied) may be required.
3. Do you have an access door in addition to the garage door? If not, model CM1702 outside quick release accessory
is required. This accessory allows manual operation of the garage door from outside in case of power failure.
4. Complete the following test to make sure your garage door is balanced and is not sticking or binding:
• Lift the door about halfway. Release the door. If balanced, it should stay in place, supported
entirely by its springs.
• Raise and lower the door to see if there is any binding or sticking. If your door binds, sticks, or is out of
balance, call a trained door technician.
As you proceed with the assembly, installation and adjustment procedures in this manual, you may find it helpful to
refer back to this illustration of a completed installation for tilt doors (for sectional doors refer section 22).
3
2
1
4
6
5
11
13
9
12
7
15
professional
www.chamberlainanz.com
8
DOOR
14
(1)
(2)
(3)
(4)
(5)
(6)
7
10
Header bracket
Idler pulley assembly
Trolley
Pole
Chain
Hanging bracket
ASSEMBLE POLE PACK
NOT
ICE
(7) Power cord
(8) Opener
(9) Light lens
(10) Manual release rope & handle
(11) Curved door arm
(12) Straight door arm
ASSEMBLY SECTION
Remove the 5 sectional poles from the carton and lay
them out on the floor. The end pole (i.e. the pole without a tapered edge) should be placed at the header
end.
Assemble the poles by inserting the tapered end into
the non-tapered end of the next pole as illustrated.
Ensure that the each pole is pushed firmly into the
next.
NOTE: If using a mallet to drive the joins home,
use a piece of timber at each end to minimise
burring.
5
(13) Door bracket and plate
(14) Trolley release arm
(15) Stop Collar
8
INSTALL THE TROLLEY AND IDLER PULLEY
Slide the trolley assembly (1) onto the pole (3) taking note of the door direction arrow (fig 1). The trolley should be located midway along the pole.
Insert the pole (3) into the idler pulley assembly (2)
as illustrated.
fig 1
DO
OR
2
1
3
9
MOUNT THE ADAPTOR BRACKET AND CHAIN SPREADER
Loosen the two (factory fitted) washered screws (4)
from the top of the opener (approx 4mm).
THESE WASHERED SCREWS MUST BE USED
TO FASTEN THE POLE KIT ADAPTOR.
1
3
2
4
Fasten the chain spreader (2) using the hex screws
(1) and washers (3) from the hardware bag provided
with the opener. Slide the adaptor bracket under the
loosened screws then tighten (20-22Nm).
10
INSTALL THE STOP COLLAR AND POLE
Slide the stop collar (1) onto the pole (2) (opener
end). Fit the pole through the adaptor bracket (3) to
the opener, then fasten the stop collar above the
edge of the lens cover as illustrated.
Move the stop collar to the open limit on the pole,
set the stop collar back 25mm toward the opener
and fasten in place. Observe the absolute stop position.
6
Absolute
minimum
stop collar
setting
2
1
3
11
INSTALL THE CHAIN
2
1
Fitting the Chain:
3
Wrap the chain around the idler pulley (1) and desired drive sprocket (as illustrated in fig 1 and 2 below),
ensuring the chain passes through the trolley assembly (3).
NOTE: Locate the chain connector (2) as illustrated above approximately 300mm from the Idler
pulley.
Additional Step for 2750mm Pole
All Chain kits supplied are for 3000mm poles. You will need
to remove the pre-measured section of chain for use with the
2750mm pole option.
Locate the two removable links and remove the section of
chain between them. Once the section of chain has been
removed use one of the joiners to re-join the shortened
chain assembly.
6 Tooth Sprocket for Tilt and larger doors
Chain Spreader
6-Tooth
Sprocket
8 Tooth Sprocket for higher speed operation
fig 1
Chain Spreader
Motor Unit
Mounting Plate
8-Tooth
Sprocket
fig 2
Motor Unit
Mounting Plate
Tighten the chain:
Once the chain has been installed, join the two
ends together using the connector. Rotate the
adjuster until the chain has no slack.
DO NOT OVER TIGHTEN!
Connecting the chain
Lock nut
Rotate adjuster
Once the chain has been tensioned, tighten the
lock nuts.
Lock nut
7
INSTALLATION SECTION
Wear protective goggles when working overhead to protect your eyes from injury.
Disengage all existing garage door locks to avoid damage to the garage door.
To avoid serious personal injury from entanglement, remove all ropes connected to the garage door
before installing the opener.
It is recommended that the opener be installed 2.1m (7 feet) or more above the floor where space permits.
POSITION THE HEADER BRACKET
The header bracket must be rigidly fastened to a
structural support of the garage. Reinforce the wall
or ceiling with a 40mm (1-1/2") board if necessary.
Failure to comply may result in improper operation
of safety reverse system.
You can attach the header bracket either to the header
wall (1) or to the ceiling (3). Follow the instructions which
best suit your particular requirements. With the door
closed, mark the vertical centerline (2) of the garage
door. Extend line onto header wall above the door.
Open door to highest point of travel. Draw an intersecting
horizontal line (4) on header wall 50mm or 200mm above
high point to provide travel clearance for top edge of
door, (height depends on door type refer section 15).
13
1
4
2
3
INSTALL THE HEADER BRACKET
NOTE: Refer to vertical centre and horizontal lines created in section 12 for proper placement of header
bracket.
A. Wall mount: centre the header bracket (1) on the vertical centre line (2) with the bottom edge of the header
bracket on the horizontal line (4) (the horizontal line
should be 50 mm for Sectional Doors & Tracked Tilt
Doors and 200mm for One Piece Tilt doors, above the
spring with the arrow pointing toward the ceiling). Mark
all of the header bracket holes (5). Drill 4.5mm (3/16")
pilot holes and fasten the header bracket with wood
screws (3).
B. Ceiling mount: extend vertical centre line (2) onto the
ceiling. Centre the header bracket (1) on the vertical
mark no more than 150mm (6") from the wall. Mark all
of the header bracket holes (5). Drill 4.5mm (3/16") pilot
holes and fasten the header bracket with wood screws
(3). For concrete ceiling mount, use concrete anchors
provided.
The Idler Pulley Bracket will also need to be turned
upside down (fig 1). To do this remove the chain from
the pulley, twist the Idler bracket 1800 in to the upside
down position & reassemble the chain around the
pulley.
CEILING MOUNT ONLY
5
4
UP
2
LY
UN
G MO
T ON
3
ILIN
CE
UP
1
5
50mm
(or 200mm)
A
5
1
2
CEILING MOUNT ONLY
UP
150mm
UP
12
3
B
OR
DO
fig 1
8
14
ATTACH POLE ASSEMBLY TO HEADER BRACKET
Position opener on garage floor below the header bracket. Use
packing material to protect the cover.
2
NOTE: To enable the Pole to clear sectional door springs, it
may be necessary to lift opener onto a temporary support.
The opener must either be secured to a support or held
firmly in place by another person. Raise the pole assembly
until chain pulley and header brackets come together.
Join with clevis pin (1). Insert R-Clip (2) to secure.
1
1
2
15
POSITIONING THE OPENER
SECTIONAL DOOR OR
TRACKED TILT DOOR
Header 50mm (2”)
Bracket above the highest
Pole
point of travel
You will need a 50mm piece of timber or similar
spacer to gauge the distance between door and rail.
1. Raise the opener onto a support.
2. Open the door completely, place a 50mm
spacer between the door and the rail (as shown).
3. If the top section or panel hits the trolley when
you raise the door, pull down on the trolley arm
to disengage the opener. Leave the trolley in
this position until opener is fastened in place.
Door
50mm spacer should
be used to determine
the correct mounting
from the ceiling
Header 50mm (2”)
Bracket above the highest
point of travel
Door
50mm spacer should
be used to determine
the correct mounting
from the ceiling
ONE PIECE TILT DOOR
You will need a 100mm (4”) piece of timber or similar
spacer to gauge the distance between door and rail.
1. Raise the door onto a support.
2. Open the door completely, place a 100mm
spacer between the door and the rail (as shown).
3. The top of the door should be level with the top
of the opener. Do not position the opener more
than 50mm (2”) above this point.
9
200mm (8”)
Header above the highest Pole
Bracket point of travel
Top of Door
100mm spacer should
be used to determine
the correct mounting
from the ceiling
16
INSTALL VIBRATION ISOLATORS
Fit the vibration isolators as indicated to help
eliminate vibration often transmitted through the
mounting surface.
Vibration Isolator
Nut
Washer
17
HANG THE OPENER
The opener must be securely fastened to a structural support of the garage.
Three representative installations are shown. Yours may be different. Hanging brackets (1) should be angled
(Figure A) to provide rigid support. On finished ceilings, (Figure B) attach a sturdy metal bracket (not supplied) (4) to a structural support before installing the opener.
For concrete ceiling mount, (Figure C), use concrete anchors (5) (provided).
On each side of opener measure the distance from the opener to the structural support (or ceiling).
Cut both pieces of the hanging bracket to required lengths. Flatten one end of each bracket and bend or twist
to fit the fastening angles. Do not bend at the bracket holes. Drill 4.5mm (3/16") pilot holes in the structural
supports (or ceiling). Attach flattened ends of brackets to supports with wood screws (2).
Lift opener and fasten to hanging brackets with screw, lock washer and nut (3). Check to make sure the pole
is centred over the door. REMOVE 50mm board. Operate door manually. If door hits the pole, raise header
bracket.
A
B
2
4
1
1
2
3
3
2
1
3
6
6
2
C
5
2
3
1
2
3
5
6
10
18
ATTACH MANUAL RELEASE ROPE & HANDLE
Thread one end of rope (1) through hole in top of red handle so "NOTICE" reads right side up as shown (3). Secure
with an overhand knot (2). Knot should be at least 25mm
(1") from end of the rope to prevent slipping. Thread other
end of rope through hole in release arm of the outer trolley
(4). Adjust rope length so that handle is 1.8m (6 feet) above
the floor. Secure with an overhand knot.
Note: If it is necessary to cut rope, heat seal the cut end
to prevent fraying.
DOOR
2
4
1
NOT
3
ICE
2
DO NOT DISENGAGE THE OPENER TO MANUAL OPERATION WITH CHILDREN, PERSONS OR OTHER OBJECTS
INCLUDING MOTOR VEHICLES WITHIN THE DOORWAY: (The door is under significant tension and if the door has
developed a fault or incorrect tension, it may be unsafe and may fall rapidly.)
Door should be released in the closed
position if possible.
To Disengage:
Pull down on the red handle.
DOOR
DO NOT USE THE HANDLE TO OPEN OR
CLOSE THE DOOR.
Engaged
To Engage:
Pull the red handle up and back towards the
opener. The trolley will engage when opener
is activated.
19
DOOR
Disengaged
INSTALL THE LIGHT
Apply slight pressure on sides of the lens (2) and hinge the lens
cover down.
Install the 40 watt maximum light bulb (1) in the socket as shown.
The light will turn on and remain lit for 2-1/2 minutes when power is
connected. After 2-1/2 minutes it will turn off.
11
1
Max. 40W
E27
2
3
20
FASTEN DOOR BRACKET
Sectional and One-Piece Door Installation Procedure:
Door bracket (1) has left and right side fastening holes. If your installation requires top and bottom fastening holes use
both the door bracket and door bracket plate (2) as shown.
1. Centre door bracket (with or without door bracket plate, as required) at the top inside face of door as shown. Mark
holes.
A. One-piece doors: locate bracket at inside face of the door 0-100mm down.
B. Sectional door: 150 - 250mm below the
top of the door.
2. A. Wooden doors
Drill 8mm holes (5/16") and fasten the door
bracket with nut, lock washer, and carriage
bolt (3).
B. Sheet metal doors
Fasten with sheet metal screws (4).
C. One-piece door optional
Fasten with wood screws (5).
3
A. 0-100mm
B. 150-250mm
4
A
B
3
1
C
1
5
1
2
2
3
4
21
CONNECT THE DOOR ARM (ONE PIECE DOORS)
Assemble the Door Arm:
• Fasten the straight and curved door arm
sections together to the longest possible
length with a 2 or 3 hole overlap (Figure 4).
• Make sure the garage door is fully closed.
Connect the straight door arm section to the
door bracket with the clevis pin.
• Secure with a ring fastener.
• Pull the emergency release handle disengage
the trolley by pulling straight down on the
emergency release cord. Slide the trolley
toward opener.
• Connect the curved arm section to the trolley
using the clevis pin and ring provided.
Figure 4
Door
Bracket
R-Clip
Lock
Washers
Nuts
Straight
Arm
Clevis Pin
Curved
Door Arm
Figure 5
Trolley
Note: When setting the up limit the door should NOT
have a backward slant when fully open as illustrated
(Figure 5). A slight backward slant will cause unnecessary buckling and/ or jerking operation as the door
is being opened or closed from the fully open position
(figure 5).
12
Correct Angle
Open Door
Door with
Backward Slant
(Incorrect)
22
CONNECT DOOR ARM FOR
(SECTIONAL DOORS)
Figure 1
Pulley
Trolley
200mm (8”) min.
Make sure garage door is fully closed. Pull the emergency release handle to disengage the trolley. Slide
the trolley assembly back 200mm from the idler pulley.
Ring
Fastener
Figure 1.
• Fasten straight door arm section to trolley
assembly using the hardware provided with
your opener.
Clevis Pin
Emergency
Release
Handle
7
Door
Bracket
Straight
Door Arm
Figure 2.
• Bring arm section together. Find two pairs
of holes that line up and join sections.
Select holes as far apart as possible to
increase door arm rigidity.
Curved Door Arm
6
Figure 2
Trolley
Pulley
Figure 3.
• If holes in curved arm are above holes in
the straight arm, disconnect straight arm
and cut approximately 150mm from
solid end. Re-connect to trolley with cut
end down as illustrated.
• Bring arm sections together.
• Find two pairs of holes that line up and join
with bolts, washers and nuts.
200mm (8”) min.
4
5
3
Door Bracket
Figure 3
Trolley
Pulley
200mm (8”) min.
HARDWARE PROVIDED
5
4
4
7
6
5
3
3
Cut this end
CONNECT ELECTRIC POWER
TO AVOID INSTALLATION DIFFICULTIES, DO NOT RUN THE GARAGE DOOR OPENER UNTIL
INSTRUCTED TO DO SO.
Connect the opener to a properly EARTHED power outlet, installed in compliance with local building
and electrical standards.
26
13
23
ADJUST THE TRAVEL LIMITS
ADJUSTMENT SECTION
Limit adjustment settings regulate the point at which the
door will stop whilst moving up or down.
To set the limits:
Ensure the door is in the CLOSED POSITION and the trolley
is engaged (see page 11)
• Turn power on
• Open the door by pressing either of your pre-programmed
transmitters or wireless wall button.
• Run the opener through a complete travel cycle.
Without a properly installed safety reversal system, persons
(particularly small children) could be SERIOUSLY INJURED or
KILLED by a closing garage door.
• Incorrect adjustment of garage door travel limits will
interfere with proper operation of safety reversal system.
• If one control (force or travel limits) is adjusted, the other
control may also need adjustment.
• After ANY adjustments are made, the safety reversal system
MUST be tested. Door MUST reverse on contact with 40mm
high object on floor.
provides adequate clearance.
NOTE: Repeated operation of the opener during adjustment procedures may cause the opener thermal protection to shut the opener down. If this occurs please wait 15
minutes and try again.
To prevent damage to vehicles, be sure fully open door
TIP: For larger doors it maybe necessary to disengage the opener to
adjust the openerʼs limits without the door attached. Re-Engage the
door and fine tune limits once the travel has been roughly adjusted.
Adjusting the limits:
The door should open a minimum of 1.5m from the CLOSED position. If door travel less than 1.5m Adjust the FORCE SETTINGS as
outlined in section 24 then return to Setting Limits.
2
1
professional
www.chamberlainanz.com
To increase the open travel limit, turn the UP limit adjustment screw
(1) clockwise (one turn = 50mm of travel).
To adjust the door closure adjust the DOWN limit adjustment screw
(2) anti-clockwise (one turn = 50mm of travel). The door should close
firmly against the floor without placing back pressure on the door
arm, pole or door fittings.
If the door fails to close firmly to the floor with the down limit adjusted fully, it may be necessary to increase the length
of the door arm (see page 20 or 21 depending on your door type). If the door reverses on contact with the floor you
will need to reduce the DOWN limit by turning the screw clockwise.
24
FORCE ADJUSTMENT
The force, as measured on the closing edge of the door, should not exceed
400N (40kg). If the closing force is measured to more than 400N, the Protector
System must be installed.
The force setting button is located on the back panel of the opener. The force
setting regulates the amount of power required to open and close the door. If
the forces are too light, door travel may be interrupted by nuisance reversals.
Locate the button (1) on the back panel of opener. Push the button twice to
enter into Force Setting Mode. The LED (Indicator Light) will flash. Push the
wall control or the programmed transmitter that was shipped with your opener.
The door will travel to either the OPEN or CLOSE position. Push the button
again, the door will travel to the opposite position. Push the button again if the
LED is stilling blinking.
The door must travel through a complete cycle UP and DOWN in order for the
force to be set properly. If the opener reverses before it reaches the Open or
Close Limit repeat the process. The LED (indicator light) will stop flashing
when the force has been learned.
14
1
24V
+
-
1
(2x)
25
TEST THE SAFETY REVERSE SYSTEM
The safety reverse system test is important. The garage door must reverse on contact with a 40mm
obstacle laid flat on the floor. Failure to properly adjust opener may result in serious personal
injury from a closing garage door. Repeat test once a month and adjust as needed.
Procedure: Place a 40mm obstacle (1) laid flat on the floor under the garage door. Operate the door in
the down direction. The door must reverse on the obstruction. If the door stops on the obstruction, it is
not travelling far enough in the down direction. Increase the down limit by turning down limit adjustment
screw counterclockwise 1/4 turn. Repeat test.
When the door reverses on the 40mm obstacle, remove the obstruction and run the opener through a
complete travel cycle. Door must not reverse in closed position. If it does, adjust Limits and Force and
repeat safety reverse test.
40mm
26
1
INSTALLATION COMPLETE
1
40mm
INSTALL THE PROTECTOR SYSTEM™
(See accessories)
Install this accessory for all installations on tilt doors, doors over 2.5m and when the closing force
as measured on the bottom of the door is over 400N (40kg).
After opener has been installed and adjusted, The Protector System™ accessory can be installed.
Instructions are included with this accessory.
The Protector System™ provides an additional measure of safety against a small child being
trapped under a garage door.
It uses an invisible beam which, when broken by an obstruction, causes a closing door to open and prevents an open door from closing and is strongly recommended for homeowners with young children.
NOTE: The opener will automatically
detect the protector system when it
is installed. The opener will not close
unless the sensors are aligned.
1. Strip wire
(11 mm)
7/16" (11 mm)
GREY
WHITE
RED
WHITE
2. Twist like colored
wires together
3. To insert or release
wire, push in tab with
screwdriver tip
Red White Grey
Quick-Connect Terminals
15
27
INSTALL WIRED DOOR CONTROLS (optional accessory)
Locate wired door controls where the garage door is visible, away from door and door hardware,
out of the reach of children and at a height of at least 1.5m.
Serious personal injury from a moving garage door may result from misuse of opener. Do not allow
children to operate the wired door controls or transmitters.
Fasten the caution label on the wall near wired door controls as a reminder of safe operating procedures.
There are 2 screw terminals (1) on the back of the wired door controls (2). Strip about 6mm (1/4") of insulation from bell wire (4). Separate wires enough to connect the white/red wire to terminal screw 1 and the
white wire to terminal screw 2.
Fasten wired door controls to an inside garage wall with sheet metal screws (3) provided. Drill 4mm (5/32")
holes and use anchors (6) if installing into plaster wall. A convenient place is beside the service door and
out of reach of children.
Run the bell wire up the wall and across the ceiling to the garage door opener. Use insulated staples (5) to
secure wire. Connect the bell wire to the spring terminals (located on the back panel) as follows: white/red
to 1 and white to 2.
1
6mm
4
WHT
-2
RED
2
LOCK
3
WHITE
RED
-1
LIGH
T
Push Bar Cover
5
4
3
24V
+
-
6
Com
No
24Vdc
al
GND ern
xt
E
er
eiv
rec
ANT
EXTERNAL RECEIVERS
Where a secondary receiver is required to
trigger your opener, power may be obtained
from the 24VDC output terminals located on the
back of your MT5580P.
1. Use the Grey 24VDC + (max 100mA) terminal and
the White GND Terminal supply power to your
24VDC receiver.
2. Run a bell wire from the COM and NO output of
your receiver into the Red and White terminals
located above the RED learn button.
24V
+
-
Com
No
24Vdc
GND
te
Ex
r
ive
ce
l re
rna
ANT
OPERATION OF THE WIRED DOOR CONTROLS
Press to open or close the door. Press again to reverse the door
during the closing cycle or to stop the door during opening cycle.
16
28
WIRELESS PROGRAMMING (OPTIONAL ACCESSORY)
Activate the opener only when door is in full view, free of obstruction and properly adjusted. No one
should enter or leave garage while door is in motion. Do not allow children to operate push button(s)
or transmitter(s). Do not allow children to play near the door.
The transmitters supplied with your opener are pre-programmed to your receiver in the factory. If you purchase
additional transmitters, you will need to program them into
your opener using the steps below.
Program the Receiver to Match Additional Transmitter
Codes:
Using the “LEARN” Button
1. Press and hold the button on the hand-held transmitter
or wireless door button that you wish to operate your
garage door (1).
2. The orange led will flash continually. Press and release
the “learn” button on the opener (2). The learn indicator
led will go out.
3. Release the transmitter or wireless door button when the
opener light blinks. It has learned the code. If light bulb
is not installed, two clicks will be heard (3).
Using the Motion Detecting Control Panel (optional
accessory):
1. Press and hold the button on the hand-held transmitter
that you wish to operate your garage door (1).
2. While holding the transmitter button, press and hold the
LIGHT button on the Motion Detecting Control Panel (2).
3. Continue holding both buttons while you press the push
bar on the Motion Detecting Control Panel (all three
buttons are held) (3).
4. Release buttons when the opener light blinks. It has
learned the code. If the light bulb is not installed, two
clicks will be heard (4).
To Erase all Transmitter Control Codes
To deactivate any unwanted transmitter(s), first erase all
codes:
Press and hold the “learn” button on the opener until the
learn indicator light goes out (approximately 6 seconds).
All previous codes are now erased. Re-program each
transmitter or keyless entry you wish to use.
PROGRAMMING C379 WIRELESS
FINGERPRINT ACCESS SYSTEM
(optional accessory)
Full instructions are available with this accessory.
Once you have enrolled your user into the C379 you can
program the unit into your opener.
Using the orange “LEARN” Button:
1. Press and release the orange “learn” button on opener.
The learn indicator light will glow steadily for 30 seconds.
2. Within 30 seconds, slide the cover of the C379 up as
illustrated (A). Swipe your finger on the reader head at a
steady speed (B) until the yellow led turns on (C).
3. When the opener light blinks (3). It has learned the
code. If the light bulb is not installed, two clicks will be
heard, ensure there are no obstructions in the path of
the door, then press the Send button (D) to test the door.
17
2
1
1
3
3
2
4
LIGHT
LOCK
LOCK
LIGHT
29
INSTALLING YOUR CM128 WIRELESS WALL BUTTON
INSTALL:
Carefully pry open the CM128 and locate the two screw for mounting.
To attach to the wall, use the two screws and wall anchors provided, if mount
to plaster wall (If using a recessed wall box do not use anchors).
NOTE: Tightening the wall mount screws will reduce clearance
between bracket and wall.
NOTE: Your CM128 Wireless wall button should be pre-programmed
into your opener, you should only need to program additional units.
+
Program CM128 Wireless wall button using the orange “LEARN”
Button:
+
+
1. Press and hold the button that you wish to operate your garage door.
2. Press and release the orange “learn” button on opener. The learn indicator light will flash continually.
3. Release the button when the opener light blinks. It has learned the code. Where no light is installed two clicks will be
heard.
30
Activate the opener only when door is in full view, free of obstruction and properly adjusted.
No one should enter or leave garage while door is in motion. Do not allow children to operate push
button(s) or transmitter(s). Do not allow children to play near the door.
Locate minimum 1.5m above the floor.
SPECIAL FEATURES OF THE MT5580P
A. Door within a door connection
Disconnect opener from power!
Remove cover. Locate auxiliary terminal block (TB1) on the control board. Remove jumper from terminal leads 1 and 2 (not shown). Replace with contact switch leads as shown.
B. Coaxial antenna adaptor
A coaxial antenna connection can be used if the transmitter range is too short.
A
B
TB1
24V
+
-
18
31
ACCESSORIES
(1) Model CM844
(2) Model CM128
(3) Model C940
(4) Model C943
(5) Model C945
(6) Model 75LM
4 Channel transmitter
Wireless wall button
Single channel transmitter
3 Channel transmitter
3 Channel mini transmitter
Illuminated door bell push button
CM844
C940
CM128
2
1
C840
(7) Model C98
(8) Model C840
(9) Model C77
(10) Model CM1702
(11) Model 760E
(12) Model C379
(13) Model ANT4X-1LM
C1702
C77
9
8
C945
C943
3
4
75LM
Max. Pull Force:
Rated Power:
11
Motor Type:
Speed:
Volts:
Drive Mechanism
Gears:
Drive:
Length of Travel:
PASS
FAIL
READY
RETRY
Travel Rate:
Lamp:
Door Linkage:
Personal:
Electronic:
Electrical:
Limit Device:
Limit Adjustment:
16:1 worm gear reduction
Chain with two piece nylon trolley
Adjustable to 2750mm (3m Pole)
/ 2500mm (2.75m Pole)
96-135mm per sec
On when door starts, off
2-1/2 minutes after stop.
Adjustable door arm. Pull cord
trolley release.
7
ENROLL
SAFETY:
Permanent split capacitor
1500rpm
230-240 Volts AC-50Hz
LIGHT
ENROLL
SEND
800N
400W
LOCK
C379
13
12
SPECIFICATIONS:
C98
6
5
760E
10
Motion detecting control panel
Keyless entry system
The Protector SystemTM
Quick release lock
Outside keyswitch
Wireless fingerprint access system
433MHz Antenna, cable and adaptor
Start Circuit:
Dimensions
Length (Overall):
Headroom required:
Hanging Weight:
Receiver Memory
Registers:
Push button stop in Up and
Down Direction. Automatic force
reversal in UP and DOWN
direction.
Automatic force adjustments.
Motor overload protector and
low voltage push button wiring
Circuit actuated by limit nut.
Screwdriver adjustment on the
side panel.
Remote or low voltage push
button circuit.
3310mm (3m Pole)
3060mm (2.75m pole)
60mm
12.5kg
8
SPECIAL NOTE: Chamberlain strongly recommends that the Protector SystemTM be installed on all garage door openers.
19
OPERATION OF YOUR OPENER
Your opener can be activated by any of the following devices:
• Wireless Wall Button (CM128). Press button down until door starts to move.
• The Outside Keyswitch or Keyless Entry System (if you have installed either of these accessories).
• The Transmitter. Hold the push button down until the door starts to move.
Opening the Door Manually:
Door should be fully closed if possible. Weak or broken springs could allow an open door to fall rapidly.
Property damage or serious personal injury could result.
The door can be opened manually by pulling the release handle down.
To re-connect the door, pull the release cord back toward the opener (refer section 18)
Do not use the manual release handle to pull the door open or closed.
When the Opener is Activated by Transmitter, Wireless wall button or (optional) Wired Wall Control Button:
1. If open, the door will close. If closed, the door will open.
2. If closing, the door will reverse.
3. If opening, the door will stop (allowing space for entry and exit of pets and for fresh air).
4. If the door has been stopped in a partially open position, it will close.
5. If an obstruction is encountered while closing, the door will reverse.
6. If an obstruction is encountered while opening, the door will reverse and stop.
7. The optional Protector SystemTM uses an invisible beam which, when broken by an obstruction, causes a closing
door to open and prevents an open door from closing. It is STRONGLY RECOMMENDED for homeowners with
young children.
Allow a 15 minute cooling period after 5 continuous operations of the opener.
The opener light will turn on: 1. when opener is initially plugged in; 2. when the power is interrupted; 3. when the
opener is activated.
The light turns off automatically after 2-1/2 minutes. Bulb size is 40 Watts maximum.
MAINTENANCE OF YOUR OPENER
Once a Month:
• Repeat safety reverse test. Make any necessary adjustments.
• Manually operate door. If it is unbalanced or binding, call for professional garage door service.
• Check to be sure door opens and closes fully. Adjust Limits and/or Force if necessary.
Once a Year:
Oil door rollers, bearings and hinges. Do not grease the door tracks.
Clean and lubricate the pole and trolley. The opener does not require additional lubrication.
CARE OF YOUR OPENER
When properly installed your opener will operate with minimal maintenance. The opener does not require additional
lubrication.
Limit and Force Adjustments: These adjustments must be checked and properly set when opener is installed. Only
a screwdriver is required. Weather conditions may cause some minor changes in the door operation, requiring some
re-adjustments, particularly during the first year of operation.
Refer to the limit and force adjustments in sections 23 and 24. Follow the instructions carefully and repeat the safety
reverse test after any adjustment.
Transmitter: The portable transmitter may be secured to a car sun visor with the clip provided. Additional transmitters
can be purchased at any time for use in all vehicles using garage. Refer to Accessories. Any new transmitters must
be set to the same code as the original transmitter.
Wireless Wall Button Batteries: When the light becomes dim or does not come on replace the batteries.
Transmitter Battery: If transmission range decreases replace the battery.
To Change Battery: To replace batteries, use the visor clip or screwdriver blade to pry open the case. Insert batteries
positive side up. To replace cover, snap shut along both sides. Do not dispose of the old battery with household
waste.
20
32
REPLACEMENT PARTS
NOT
ICE
178B0086B
091B0019
012B0905
E
AS
RE
IL G 3A4
.8
NO
RA
012B0906
083A0011-1
178B0034B
002A1659
002A1658
001A7350
012B0415
PDR30005
2.75m Segmented Pole Pack
012B0921
001A6793-1
001A4208-2
001A6829
21
001A4627
32
REPLACEMENT PARTS
041A3261-1 (Dual Sprocket)
If the supply cord is damaged,
it must be replaced by the
manufacturer, its service agent
or similarly qualified persons
in order to avoid hazard.
041A5833
026B0072
175B0174
041B4375
041A5813
108D0068-1
041A5831-10
041A5809
030B0415
081C0253
041A5432
041A5525-71
22
041C4398A
Troubleshooting
1. Opener doesn't operate from either door control or transmitter:
• Does the opener have electric power? Plug lamp into outlet. If
it doesn't light, check the fuse box or the circuit breaker. (Some
outlets are controlled by a wall switch.)
• Have you disengaged all door locks? Review installation
instruction warnings on page 2.
• Is there a build-up of ice or snow under door? The door may be
frozen to ground. Remove any obstruction.
• The garage door spring may be broken. Have it replaced.
• Repeated operation may have tripped the overload protector in
the motor. Wait 15 minutes. Try again.
2. Opener operates from transmitter but not from door control:
• Is door control button lit? If not, remove the bell wire from the
opener terminals. Short the red and white terminals by touching
both terminals at the same time with a piece of wire. If the
opener runs, check for a faulty wire connection at the door control, a short under the staples, or a broken wire.
• Are wiring connections correct? Review page 18.
3. Door operates from door control but not from transmitter:
• Check battery. Replace battery if necessary.
• Is the light at the wall control flashing? Press button with keysymbol to unlock the opener against transmitters.
• Is the receiver LED flashing at the back of the opener when the
transmitter is pressed? The opener receiver must re-learn the
transmitter code. Follow the instructions on page 17.
• If you purchased a new transmitter then check at carton of
transmitter or compatibility or call a Merlin Professional dealer.
4. Transmitter has short range:
• Is battery installed? If needed, change the battery.
• Change the location of the transmitter on the car.
• A metal garage door, foil-backed insulation or metal siding will
reduce the transmission range.
• Use outside coaxial antenna adaptor to move antenna.
5. Door reverses for no apparent reason and opener light
doesn't blink:
• Is something obstructing the door? Pull manual release handle.
Operate door manually. If it is unbalanced or binding, call for
professional garage door service.
• Clear any ice or snow from garage floor area where garage
door closes.
• Review Force Settings. Open and close the door in learn mode
for several (3-5) consecutive cycles to allow the operator to
adjust to inconsistent doors.
• If door reverses in FULLY CLOSED position, re-learn travel limits.
Repeat safety reverse test after adjustment is complete.
The need for occasional adjustment of the force and limit settings is normal. Weather conditions in particular can affect door
travel.
6. Door reverses for no apparent reason and opener light
blinks for 5 seconds after reversing:
Check The Protector System™ (if you have installed this accessory). If the light is blinking, correct alignment.
Note: Continuously holding down the door control button will
allow the door to close if the protector system is not properly
aligned. The transmitter will not close the door. The opener lights
will blink.
7. The garage door opens and closes by itself:
• Delete all transmitters and re-program.
• Make sure transmitter push button is not stuck "on".
• Disconnect all push buttons or key switches attached and wait
one day.
23
8. Door stops but doesn't close completely:
Review Limit Adjustment section.
Repeat safety reverse test after any adjustment of door arm
length, close force or down limit.
9. Door opens but won't close:
• Check The Protector System™ (if you have installed this
accessory). If the light is blinking, correct alignment.
• If opener light does not blink and it is a new installation, check
the down force.
Repeat the safety reverse test after the adjustment is complete.
10. Opener light does not turn on:
Replace light bulb (40 Watts maximum).
11. Opener light does not turn off:
There may be a defective earth at the ceiling or wall receptacle.
The opener must be earthed.
12. Opener strains or reversed during opening:
Door may be unbalanced or springs are broken. Close door and
use manual release rope and handle to disconnect trolley. Open
and close door manually. A properly balanced door will stay in
any point of travel while being supported entirely by its springs.
If it does not, call for professional garage door service to correct
the problem. Do not change force settings.
13. Opener motor hums briefly, then won't work:
• Garage door springs are broken. SEE ABOVE.
• If problem occurs on first operation of opener, door is locked.
Disable door lock. If chain was removed and reinstalled, the
opener may be out of phase. Remove chain; cycle opener to
down position. Observe drive sprocket. When it turns in clockwise direction and stops in down position, re-install chain.
Repeat safety reverse test after adjustment is complete.
14. Opener won't activate due to power failure:
• Pull manual release rope and handle down and back to disconnect trolley. Door can be opened and closed manually. When
the power is restored, pull the manual release handle straight
down. The next time the opener is activated, the trolley will reconnect.
• The Outside Quick Release accessory (if fitted) disconnects
the trolley from outside the garage in case of power failure.
CHAMBERLAIN LIMITED WARRANTY
Merlin Professional MT5580P
Sectional Garage Door Opener
Chamberlain Australia Pty Limited / Chamberlain New Zealand Limited
(Chamberlain), the manufacturer of Merlin® automatic garage door openers, is committed to manufacturing and supplying high quality goods. As
part of this commitment, we seek to provide reliable service and support
for our goods and are pleased to provide you, the original purchaser, with
this Chamberlain Limited Warranty.
We also provide the following statement as required by the Australian
Consumer Law: In Australia, in addition to your rights under this
Chamberlain Limited Warranty, our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to
a replacement or refund for a major failure and for compensation for any
other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
Chamberlain’s warranty
Chamberlain warrants to the original purchaser of the Merlin® MT5580P
Sectional Door Opener (Unit) that all parts of the Unit, other than remote
controlled transmitters and accessories, globes and batteries, are free
from defects in materials and workmanship for a period of 24 months or
5,000 cycles (opening & closing of the garage door) whichever comes
first, from the date of purchase when installed in a residential premise
with a residential specified garage door that is designed for the sole purpose of domestic domicile. Chamberlain warrants the motor component
of the opener for 5 years or 15,000 cycles whichever comes first.
Chamberlain warrants that remote controlled transmitters and accessories
included with the Unit are free from defects in materials and workmanship
for a period of 12 months from the date of purchase.
Batteries and globes are not covered under the Chamberlain Limited
Warranty.
It is a condition of this Chamberlain Limited Warranty that the Unit is sold,
installed and serviced by a Professional Dealer appointed by
Chamberlain. A Merlin® branded garage door opener purchased over the
internet and installed by a person other than a Professional Dealer will not
be covered by this Chamberlain Limited Warranty.
It is also a condition of this warranty that the garage door is operable by
hand and opens and closes with no more than a maximum of 20kgs of lifting weight. Chamberlain recommends that the garage door is serviced by
a garage door technician every 12 months. This garage door service fee
will be at the consumer’s expense.
NB: The Australian Garage Door Association directs attention to consumers to maintain your garage door in good running order it is important
your door is serviced by a professional garage door technician every 12
months or earlier as conditions may require.
During the applicable Chamberlain Limited Warranty period, if you are
concerned that the Unit may be defective, for prompt on-site service call
the Professional Dealer that sold/installed the opener, or our service centre on the toll free number below and a Chamberlain technician will diagnose the problem and arrange for this to be rectified. Once the problem
has been diagnosed, subject to your rights under the Australian
Consumer Law with respect to major failures, Chamberlain or its
Professional Dealer will provide you with:
1. repairs to the Unit
or
2. a replacement Unit.
Repairs and replacement parts provided under this Chamberlain Limited
Warranty are provided free of charge and are warranted for the remaining
portion of the original warranty period.
This Chamberlain Limited Warranty provides benefits which are in addition
to your other rights and remedies as a consumer.
Exclusions
If our service centre determines that a warranty claim has been made in
respect of a failure or defect arising under or out of any exclusion detailed
below such that the claim is not covered under this Chamberlain Limited
Warranty, we may, subject to your other rights and remedies as a
114A3694E
consumer, charge you a fee to repair, replace and/or return the Unit to
you.
This Chamberlain Limited Warranty does not cover any failure of, or
defect in, the Unit due to:
1 non-compliance with the instructions regarding installation, operation,
maintenance and testing of the Unit or of any product with which the Unit
is used;
2 any attempt by a person other than a Professional Dealer to repair,
dismantle, reinstall or move the Unit to another location once it has been
installed;
3 tampering, neglect, abuse, wear and tear, accident, electrical storm,
excessive use or conditions other than normal domestic use;
4 problems with, or relating to, the garage door or garage door hardware, including but not limited to the door springs, door rollers, door
alignment or hinges;
5 problems caused by electrical faults or replacement of batteries or
light bulbs;
6 water or moisture ingress that causes corrosion or electrical malfunction;
7 corrosion caused by sea air if located near a waterway, beach etc; or
8 fitment to a commercial door or in a commercial operating application.
NB: A General Purpose Outlet (GPO) ie: power point must be supplied by
the consumer as this electrical fitting does not form a part of the Unit
(opener).
If this Chamberlain Limited Warranty does not apply, you may have rights
available to you under the Australian Consumer Law.
Liability – Australia only
Except as set out in the Australian Consumer Law (being Schedule 2 of
the Competition and Consumer Act 2010) (as amended, consolidated or
replaced):
1 all other guarantees, warranties and representations in relation to the
Unit or its supply are excluded to the extent that Chamberlain can lawfully exclude them; and
2 under no circumstances will Chamberlain be liable for consequential,
incidental or special damages arising in connection with the use, or
inability to use, the Unit, other than those which were reasonably foreseeable as liable to result from the failure.
Liability – New Zealand only
Except as set out in the Fair Trading Act 1986 and the Consumer
Guarantees Act 1993 (as amended, consolidated or replaced):
1 all other guarantees, warranties and representations in relation to the
Unit or its supply are excluded to the extent that Chamberlain can lawfully exclude them; and
2 under no circumstances will Chamberlain be liable for consequential,
incidental or special damages arising in connection with the use, or
inability to use, the Unit, other than those which were reasonably foreseeable as liable to result from the failure.
Note: We request that you retain your sales docket or invoice as
proof-of-purchase and attach it to this manual to enable you to
establish the date of purchase in the unlikely event of a warranty
service being required. Chamberlain reserves the right to change
the design and specifications of the Unit without prior notification.
Some features or accessories of the Unit may not be available in
certain markets or areas. Please check with your distributor.
Chamberlain service centre contact details
Australia
Phone toll free 1800 638 234
Fax toll free 1800 888 121
Chamberlain Australia Pty. Ltd.
PO BOX 1446
Lane Cove NSW 1595
New Zealand
Auckland phone 09 477 2823
Phone toll free 0800 653 667
Fax toll free 0800 653 663
Email: [email protected]
Website: www.merlingo.com
24
Trademark of The Chamberlain Group, Inc.
® Registered Trademark of The Chamberlain Group, Inc.
TM
© 2011, The Chamberlain Group Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement