Alto DX 985 Operating instructions

Alto DX 985 Operating instructions
DX 845 W
DX 865
DX 985
Titan Energy
Titan Energy X
Betriebsanleitung ...................... 2
Operating Instructions .............. 8
Notice d'utilisation .................. 14
Gebruiksaanwijzing ................ 20
Istruzioni sull'uso..................... 26
Käyttöohje ............................... 32
Navodilo za uporabo ................... 38
Uputstvo za rad ............................ 44
Prevádzkový návod ..................... 50
Provozní návod ............................ 56
Instrukcja obsługi ........................ 62
Kezelési utasítás.......................... 68
Instrucciones de manejo ......... 74
Instruções de operação ........... 80
Οδηγίες λειτουργίας ................. 86
Ýþletme kýlavuzu....................... 92
DX 845 W / DX 865 / DX 985 / Titan Energy / Titan Energy X
1
9
8
TIT
AN
EN
ER
GY
0
5
140
60
10
212
10
0
1
3
0
70
20
F
C
1
14 285
0
A
3
5
C
5
B
F
7
11
6
4
3
2
1
14
15
16
17
13
18
12
DX 845 W / DX 865 / DX 985 / Titan Energy / Titan Energy X
2
5
3
4
6
7
9
10
4
1
3
2
8
1
2
11
12
13
0
14
0
60
21
10
70
20
F
C
2
0
1
A
C
max
B
min
EG - Konformitätserklärung
Déclaration de conformité CE
Wap Reinigungssysteme GmbH & Co.
Guido-Oberdorfer-Straße 2-8
D-89287 Bellenberg
Wap Reinigungssysteme GmbH & Co.
Guido-Oberdorfer-Straße 2-8
D-89287 Bellenberg
Erzeugnis:
Hochdruckreiniger
Produit:
Nettoyeur haute pression
Typ:
DX 845 W, DX 865,
DX 985, Titan Energy, Titan Energy X
Type:
DX 845 W, DX 865,
DX 985, Titan Energy, Titan Energy X
Beschreibung:
IP X5, Schutzklasse I, 50 Hz.
Description:
IP X5, Classe de protection I, 50 Hz.
La construction de l’appareil est
conforme aux réglementations
afférentes suivantes:
Directive CE relative aux machines
89/392/EWG
Directive CE relative à basse tension 73/23/EWG
Directive CE EMV
89/336/EWG
89/392/EWG
Die Bauart des Gerätes entspricht EG-Maschinenrichtlinie
EG-Niederspannungsrichtlinie 73/23/EWG
folgenden einschlägigen
EG-Richtlinie EMV
89/336/EWG
Bestimmungen:
Angewendete harmonisierte
Normen:
EN 292
EN 60335-1, EN 60555-3
EN 50081
Normes harmonisées appliquées:
EN 292
EN 60335-1, EN 60555-3
EN 50081
Angwendete nationale Normen
und technische Spezifikationen:
DIN EN 60335-1
E-DIN VDE 0700 T 265
IEC 335-2-79
Normes nationales et
spécifications techniques
appliquées:
DIN EN 60335-1
E-DIN VDE 0700 T 265
IEC 335-2-79
Johan Ley
VP Tech-OP
Dipl.Ing. W. Nieuwkamp
Prüfungen und Zulassungen
Bellenberg, 21.08.2000
Johan Ley
VP Tech-OP
EU Declaration of Conformity
Dipl.Ing. W. Nieuwkamp
Controles et homologations
Bellenberg, 21.08.2000
Dichiarazione di conformità CE
Wap Reinigungssysteme GmbH & Co.
Guido-Oberdorfer-Straße 2-8
D-89287 Bellenberg
Wap Reinigungssysteme GmbH & Co.
Guido-Oberdorfer-Straße 2-8
D-89287 Bellenberg
Product:
High Pressure Cleaner
Prodotto:
Pulitrice ad alta pressione
Type:
DX 845 W, DX 865,
DX 985, Titan Energy, Titan Energy X
Tipo:
DX 845 W, DX 865,
DX 985, Titan Energy, Titan Energy X
Description:
IP X5, Protection class I, 50 Hz.
Descrizione:
IP X5, Classe di protezione I, 50 Hz.
The design of the unit corresponds EC Machine Directive
to the following pertinent
EC Low-voltage Directive
regulations:
EC EMV Directive
Applied harmonised standards:
Applied national standards and
technical specifications:
Johan Ley
VP Tech-OP
89/392/EWG
73/23/EWG
89/336/EWG
EN 292
EN 60335-1, EN 60555-3
EN 50081
DIN EN 60335-1
E-DIN VDE 0700 T 265
IEC 335-2-79
Dipl.Ing. W. Nieuwkamp
Tests And Approvals
Bellenberg, 21.08.2000
La costruzione dell' apparecchio è Direttiva CE sulle macchine
conforme alle seguenti direttive Direttiva CE sulla bassa tensione
specifiche:
Direttiva CE sulla compatibilità
elektromagnetica
Norme armonizzate applicate:
EN 292
EN 60335-1, EN 60555-3
EN 50081
Norme nazionali applicate e
specifiche tecniche:
DIN EN 60335-1
E-DIN VDE 0700 T 265
IEC 335-2-79
Johan Ley
VP Tech-OP
Atestado de conformidad de la UE
Dipl.Ing. W. Nieuwkamp
Controlli e omologazioni
89/392/EWG
73/23/EWG
89/336/EWG
Bellenberg, 21.08.2000
EG-Verklaring van overeenstemming
Wap Reinigungssysteme GmbH & Co.
Guido-Oberdorfer-Straße 2-8
D-89287 Bellenberg
Wap Reinigungssysteme GmbH & Co.
Guido-Oberdorfer-Straße 2-8
D-89287 Bellenberg
Producto:
Máquina de limpieza a alta presión
Produkt:
Hogedrukreiniger
Modelo:
DX 845 W, DX 865,
DX 985, Titan Energy, Titan Energy X
Type:
DX 845 W, DX 865,
DX 985, Titan Energy, Titan Energy X
Descripción:
IP X5, Clase de protección I, 50 Hz.
Beschrijving:
IP X5, Beschermklasse I, 50 Hz.
La construcción de la máquina
corresponde a las siguientes
normas específicas:
R. de la UE para máquinas 89/392/EWG
R. de la UE para baja tensión
73/23/
EWG
R. de la UE para la compatibilidad electromagnética
89/336/EWG
De constructie van het apparaat
voldoet aan de volgende van
toepassing zijnde voorschriften:
EG-machinerichtlijn
EG-laagspanningsrichtlijn
EG-richtlijn EMV
Normas armonizadas aplicadas:
EN 292
EN 60335-1, EN 60555-3
EN 50081
Toegepaste geharmoniseerde
normen:
EN 292
EN 60335-1, EN 60555-3
EN 50081
Normas nacionales aplicadas y
especificaciones técnicas:
DIN EN 60335-1
E-DIN VDE 0700 T 265
IEC 335-2-79
Toegepaste nationale normen en
technische specificaties:
DIN EN 60335-1
E-DIN VDE 0700 T 265
IEC 335-2-79
Johan Ley
VP Tech-OP
Dipl.Ing. W. Nieuwkamp
Pruebas y homologaciones
Bellenberg, 21.08.2000
Johan Ley
VP Tech-OP
Dipl.Ing. W. Nieuwkamp
Keuringen en vergunningen
89/392/EWG
73/23/EWG
89/336/EWG
Bellenberg, 21.08.2000
DX 845 W / DX 865 / DX 985 / TitanEnergy / TitanEnergy X
READ THE OPERATING
INSTRUCTIONS AND
OBSERVE THE
ENCLOSED SAFETY
NOTES!
GB
Dear Alto customer,
We thank you for the faith which
you have placed in Alto and are
sure that you have made the
right decision.
Unsuitable cleaning
agents lead to poor
cleaning results and
cause damage to the
machine. Predilute the
concentrate as
instructed.
No.
GENERAL
Use only Alto products developed
for your high-pressure cleaner as
cleaning agents.
Your Alto high-pressure cleaner
has been developed specially for
professional use.
We observe time and again that
faults are due to the use of
unsuitable products.
If you observe these operating
instructions and comply with the
notes given, your high-pressure
cleaner will help you in your
cleaning work for many years to
come.
The following table gives an
overview of the potential applications and of the corresponding
Alto cleaning agents.
pH
Pure or
pre- value in
1%
diluted
solution
approx.
%
5,0
Undiluted
4,0
3,0
1:1
Alto AutoActive
Intensive acting concentrate
against dust, soot, greases, 81218
oils and insect residues. For
delicate surfaces.
2,0
1:2
1:10
9,5
1,0
1:5
0
1:10
1:20
0
Alto Intensive
Multi-purpose concentrate
for heavy soiling on
engines, machine parts, in
workshops, on trucks and
on tarpaulins.
19
32
45 Additivethroughput approx. l/h
Setting on the
metering valve
81227
DESCRIPTION (FIG. 1)
1 RotoFix high-pressure spray
lance with VarioPress trigger
gun1)
2 Water connection
3 Steering roller with parking
brake
4 High-pressure connection
5 Cleaning agent tank
6 Mains cable storage point
7 Hose storage point
8 Spray lance storage clip
9 Exhaust pipe
10 Operating panel
11 Fuel tank
12 Pressure gauge
13 Temperature controller
14 Operation indicator light
15 Fuel shortage indicator
16 Scale alarm1)
17 Operating mode switch
18 Cleaning agent metering
knob
8
6
Mixing ratio
1:10
9,1
Further highly effective cleaning and care
agents can be found in the catalogue "Alto
Cleaning and Care Agents".
BEFORE STARTING WORK
If the machine is to be operated
at fuel stations or in other
potentially hazardous areas, the
machine may only be employed
outside the hazard areas defined
in the "Technical Guidelines for
Inflammable Fluids" applicable at
the point of use due to the
potential explosion hazard posed
by the burner.
building regulations must be
observed. We will be glad to
provide tips for connection
systems, on request.
The machine must be supervised
at all times so that the operator
can notice when the flame goes
out.
ð Secure the machine with
the parking brake (Fig. 2).
ð Check the oil level in the
high-pressure pump (Fig. 3).
ð Fill the cleaning agent tank
If the machine is to be operated
indoors, the local building
regulations must be observed for
the discharge of the exhaust
fumes into the atmosphere.
Ensure an adequate supply of
fresh air.
If the machine is to be connected
to a flue gas stack, the state
with prediluted Alto cleaning
agent.
ð With the machine cold:
Pour fuel (fuel oil EL, biodiesel
E to DIN 51 606 or diesel fuel
to DIN 51 603) into the fuel
tank.
The fuel must be free from
contamination.
– Tank capacity: 30 litres
1)
Option / model variants
DX 845 W / DX 865 / DX 985 / TitanEnergy / TitanEnergy X
COLD WATER OPERATION
OPERATION OF THE ROTOFIX
HIGH-PRESSURE SPRAY LANCE
ð Release the lock of the trigger
+
ð
ð
ð
ð
ð
ð
ð
Unsuitable fuels must not be
used as they can represent a
source of danger.
At temperatures below 8° C,
the fuel oil begins to solidify
(paraffin precipitation). This
can lead to difficulties in
starting the burner. Before the
winter period either add a
solidification point / flow
improver (available from the
fuel oil trade) to the fuel or
use winter diesel fuel.
Fill the tank for the Alto
automatic scale alarm system.
"Alto Anti-Stone" prevents any
deposits of scale and acts at
the same time as a corrosion
inhibitor. Use the bottle
supplied with the pack for
filling (Fig. 4). For compatibility reasons, use only the tested
"Alto Anti-Stone". Order the
refill pack 6 x 1000 ml, No.
8466, in good time.
Screw the high-pressure hose
firmly onto the VarioPress
trigger gun1), pushing back the
slide of the locking pin (Fig. 5/
1 + 5/2).
Securely tighten the screw of
the Roto-Fix high-pressure
spray lance, at the same time
pushing back the slide of the
locking pin (Fig. 5/3 + 5/4).
Connect the water hose (Fig. 6).
The use of a fabric-reinforced
water hose with a nominal
diameter of at least 1/2" (13
mm) is recommended.
Connect the high-pressure
hose to the high-pressure
connection. Ensure that the
union nut is securely tightened
(Fig. 7)!
Turn on the water tap.
Insert the plug of the cleaner
into the plug socket.
STARTING OPERATION
+
1)
RTING OPERATION
The pipework of the machine
is filled with antifreeze.
Collect the first liquid (approx.
5 litres) which comes out of
the spray gun in a suitable
vessel for further use.
Option / model variants
gun and press the trigger (Fig.8).
ð Turn the operating mode
switch to position
.
-> The function test of the
displays on the operating
panel starts.
– All the indicator lights
come on briefly, then the
indicator light
comes on
continuously to indicate
that the machine is ready
for operation.
ð Operate the trigger of the
trigger gun several times at
short intervals to bleed the
system.
HOT WATER OPERATION
The RotoFix high-pressure spray
lance allows the spray lance to
be turned for pressure-free
operation:
ð Push back the slide of the
locking pin (Fig. 5).
ð Turn the screw fitting of the
RotoFix high-pressure spray
lance until the pin engages in
the next bore.
OPERATION OF THE COAXIAL
SPRAY LANCE1)
ð The working pressure can be
steplessly varied by turning the
handle of the spray lance, but
with a constant volume of
water (Fig. 10).
ð Select the temperature (20-
100° C).
ð Release the lock of the trigger
gun and press the trigger (Fig.8).
ð Turn the operating mode
switch to position
.
ð When a steady jet emerges
from the high-pressure nozzle,
turn the operating mode
switch to position
.
Using a special device1), the
condensate coming out of the
heat exchanger can be collected
and disposed of in accordance
with the local sewage regulations; water poured in and emerging at the nozzle then has the
same composition.
STEAM OPERATION
(OVER 100° C)1)
Replace the standard highpressure nozzle with the steam
spray nozzle (No. 6692)1). Set the
thermostat to a temperature of
above 100° C. Turn the rotary
knob on the safety control block
completely to the left (anticlockwise direction) (Fig. 9). Release
the lock of the trigger gun and
press the trigger. Turn the operating mode switch to position
When a steady jet emerges from
the steam spray nozzle, turn the
operating mode switch to position
.
OPERATION OF THE PRESSURE
AND WATER VOLUME
CONTROLLER
DX 845 W:
ð The rotary knob on the safety
control block allows the
pressure and water volume to
be steplessly varied (Fig. 9).
DX 865, DX 985, TitanEnergy,
TitanEnergy X:
Stepless variation of pressure and
water volume
ð Continuous operation =
Rotary knob on the safety
control block (Fig. 9).
ð Brief operation = Rotary knob
on the VarioPress trigger gun1)
(Fig. 11).
The set pressure can be read off
from the pressure gauge.
USE OF CLEANING AGENTS
ð Predilute cleaning agents as
described under "General"
and pour into the cleaning
agent tank.
ð Set the desired concentration
of the cleaning agent (table,
see section "General") at the
metering valve (Fig. 12).
ð Spray the object to be cleaned.
ð Allow the cleaning agent to
9
GB
DX 845 W / DX 865 / DX 985 / TitanEnergy / TitanEnergy X
GB
+
work, depending on the
degree of soiling, then rinse
off with the high-pressure
spray jet.
The cleaning agent must
not be allowed to dry on
the surface!
PUMP SYSTEM
SERVICE AND MAINTENANCE
ð Clean the screens and filter in
The maintenance operations
marked with
should only be
carried out by the Alto service
technician.
the water inlet line (float
valve, high-pressure pump
inlet).
ð Grease the manual screw
fittings on the spray lance and
high-pressure hose.
MAINTENANCE SCHEDULE
FINISHING OPERATION AND
STORAGE
ð Turn the metering valve to
ð
ð
ð
ð
ð
ð
ð
ð
position .
Turn the operating mode switch
to position
.
Allow the machine to run for
approx. 1 minute, then turn the
operating mode switch to
position OFF.
Actuate the trigger gun until the
machine is completely depressurised.
Insert the safety lock (Fig. 8/1).
Turn off the water tap.
Pull the machine plug out of the
plug socket and coil up the
mains cable.
Disconnect the water hose from
the machine.
Store the machine in a frostproof room where it is safe from
unauthorised use.
If the machine cannot be stored in a
frost-proof room, proceed as follows:
ð Turn off the water tap.
ð Turn the operating mode switch
to position
and actuate
the trigger gun
ð Gradually pour antifreeze
(approx. 5 litres) into the water
tank.
ð The machine is protected against
frost when antifreeze solution
emerges from the nozzle of the
spray lance.
ð When the machine is put into
service again, the antifreeze
solution can be collected and
stored for future use.
Weekly or every 40 operating hours
ð Check the oil level
Every 3 months or every
200 operating hours
ð Change the pump oil
ð Pump system
ð Flame sensor
Annually or every 500
operating hours
ð Heat exchanger and
ignition system
ð Fuel system
As required
ð Grease the manual
screw fittings on the
spray lance and highpressure hose
ð Descale the system
FLAME SENSOR
ð Remove the sensor and clean
+
with a soft cloth.
Ensure that the sensor is
correctly seated when installing again.
HEAT EXCHANGER AND
IGNITION SYSTEM
ð Have cleaning carried out by
the Alto service technician,
see "Maintenance schedule".
FUEL SYSTEM
ð Empty the fuel tank. Clean
the tank and fuel lines.
ð Dispose of the cleaning fluid
in accordance with the
disposal regulations.
OIL LEVEL CHECK / OIL
CHANGE
Check the oil level in the highpressure pump regularly at the
oilglass (Fig. 3).
ð Top up with oil when required.
ð If the oil has a grey or white
shade, change the oil.
Unscrew the oil drain plug on
the pump housing and
dispose of the old oil in
accordance with the disposal
regulations.
ð Renew the drain plug gasket
and screw in the plug again.
ð Fill with oil and close the oil
filler plug.
Oil grade:
AlphaSynt 150
(Order-no. 5218433)
Oil capacity: DX 0.35 l
SETTING OF THE ALTO
AUTOMATIC SCALE ALARM
SYSTEM
The automatic scale alarm
system is set at the factory to
water hardness class 2. Should
an adjustment be necessary,
proceed as follows:
ð Measure the water hardness
or ask your water supply
company.
ð Set the number of drops per
minute (see table) at the
metering device (Fig. 13).
Hardness
class
1 soft
2 medium-
°dH
0-7
7-14
hard
3 hard
14-21
4 very hard >21
Drops/min.
10
20
30
40
1°dH = 1,25°e = 1,79°f
10
1)
Option / model variants
DX 845 W / DX 865 / DX 985 / TitanEnergy / TitanEnergy X
DESCALING
Descaling agents cause burns.
Avoid contact with the skin,
eyes and clothes. Wear appropriate protective clothing (e.g.
gloves, face mask, apron).
Only approved scale removers
may be used for descaling.
Use Alto Stone-EX, No. 81236
+
With regular use of Alto
Anti-Stone, descaling will
normally not be necessary.
Incorrect operation of the machine or the use of non-approved
cleaning agents can cause
deposits in the pipework system.
Scaling is caused by the water
hardness and is indicated by a
gradual increase in the water
pressure displayed on the pressure gauge.
If the working pressure is exceeded by 10 bar (with the VarioPress trigger gun open), the
system must be descaled.
Procedure:
ð Unscrew the high-pressure
nozzle from the spray lance
and place separately in the
Alto scale remover.
ð Draw in Alto scale remover
via the metering valve by
hanging a cleaning agent
hose into the scale remover
bottle and setting the metering valve to maximum
concentration.
ð Hold the spray lance in a
separate container to collect
the discharged liquid.
ð Switch on the high-pressure
pump.
ð Actuate the trigger gun. Alto
scale remover is drawn in and
emerges from the spray lance
foaming vigorously after
approx. 1 minute.
ð Switch off the high-pressure
pump and allow the scale
remover to work for approx.
15 minutes.
ð Flush out the pump system
well with clean water.
ð After approx. 2 minutes, a
1)
Option / model variants
steady jet of water must
emerge at the water outlet
tube. If this is not the case,
repeat the descaling procedure.
ð Screw the high-pressure
nozzle onto the spray lance.
GB
FROST PROTECTION
If the high-pressure cleaner is
stored in a room in which temperatures of below 0° C can occur,
antifreeze must first be flushed
through the pump.
During the flushing process,
actuate the trigger gun 2 or 3
times.
In order to avoid any risk, the
machine should preferably be
stored for a short period in a
heated room before it is put into
service again.
11
DX 845 W / DX 865 / DX 985 / TitanEnergy / TitanEnergy X
GB
TROUBLESHOOTING
Before working on the machine, remove the mains lead
plug and depressurise the
machine.
CAUSE
FAULT
REMEDY
‡
Display
does not light up,
machine does not start
>
Fault in the mains cable
ð Have electrical connection checked
‡
Display
flashes rapidly (5x per
second), motor has cut out and will
not start again
>
Motor overheated
ð Clean or replace clogged high-
pressure nozzle
ð Set the VarioPress control knob
on the trigger gun to a higher
pressure
ð Possible phase failure; have
electrical connection checked
‡
Display
is lit continuously
>
Anti-Stone concentrate container
empty
ð Top up anti-scale concentrate
container
‡
Display
is lit continuously
>
>
>
Fuel tank empty
Contamination or water in fuel
Burner sooted
ð Top up fuel tank
ð Clean fuel tank and pipework
ð Have burner setting checked
‡
Display
second)
flashes slowly (1x per
>
Inadequate water inlet
ð Use water hose with at least 1/2"
>
>
Cleaning agent tank empty
Pressure and volume controller or
VarioPress trigger gun set too low
ð Top up cleaning agent tank
ð Set pressure and volume controller
diameter, clean filter in water inlet
or VarioPress control knob on the
trigger gun to a higher pressure
‡
flashes rapidly (5x per
Display
second), burner will not start again
>
>
Flame sensor sooted
Fault in ignition or fuel system
ð Remove and clean
ð Call service technician
‡
Machine stops and starts intermittently with the trigger gun open
>
High-pressure nozzle soiled
ð Clean or replace high-pressure
>
Machine scaled
ð Descale according to the instruc-
nozzle
tions
‡
‡
‡
12
Machine stops and starts intermittently with the trigger gun closed
Pressure too low
Cleaning agent is not drawn in
>
>
>
>
>
Trigger gun leaking
High-pressure hose, high-pressure
screw fitting or pipework leaking
ð Inspect the trigger gun
ð Retighten screw fittings, replace
Cleaning agent tank empty
High-pressure nozzle worn
Pressure and volume controller or
VarioPress trigger gun set too low
ð Top up cleaning agent tank
ð Replace high-pressure nozzle
ð Set pressure and volume controller
>
>
>
Filter in water inlet clogged
High-pressure pump drawing in air
Suction or pressure valve of highpressure pump soiled or defective
>
>
>
Cleaning agent tank empty
Sludge in cleaning agent tank
Suction valve at cleaning agent
inlet soiled
high-pressure hose or pipework
or VarioPress control knob on the
trigger gun to a higher pressure
ð Clean filter
ð Repair leaks
ð Clean or replace valves
ð Top up cleaning agent tank
ð Clean cleaning agent tank
ð Remove suction valve and clean or
replace
1)
Option / model variants
DX 845 W / DX 865 / DX 985 / TitanEnergy / TitanEnergy X
GB
TECHNICAL DATA
DX 845
840 W DX
DX
865
865
Working pressure
bar
100-25
100-30
Permissible overpressure
bar
200/32
Volumetric flow
l/h
700-400
Permissible temperature
Voltage 230 V AC
Voltage 200 V 3-phase AC
Voltage 220 V 3-phase AC
Voltage 230 V 3-phase AC
Voltage 380 V 3-phase AC
Voltage 380-415 V 3-phase AC
Voltage 400-415 V 3-phase AC
Frequency
°C
80...140
EU
Rated power
Fuse
Hz
kW
A
Protection class
Type of protection
Water volume of the heater coil
l
Heating capacity
kW
Fuel tank capacity
l
Cleaning agent tank capacity
l
Permissible water inlet pressure bar
Dimensions L x W x H
mm
Machine weight
(weight of trigger gun)
kg
Sound pressure level at a
distance of 1 m from
the machine DIN 45635
dB(A)
Oil fill capacity
l
Recoil forces
N
E,B,N
50
DX 905
TitanEnergy
170-25 190-30
190-25 180-30
170-30
175-25 (JP) 180-25 (JP,KR)
250/32 250/32
250/32 250/32
250/32
DXDX
985
985
Titan
Plus
TitanEnergyX
200-25
200-30
180-25
180-30
100-30 (UK)
250/32
250/32
200/32 (UK)
900-400
900-400
700-400 (UK)
80...140
80...140
UK
250/32
250/32
800-400 900-400
900-400900-400 980-400
800-400
980-400
775-400 (JP) 850-400 (JP)
80...140 80...140
80...14080...140 75...140
80...140
75...140
JP
KRKR
E,B,N
JP
KR KR
E,B,N
EUEU
EU EU
E,B,N
E,B,N
EUEU
EU
EU
5050
50
50
UK
5050
50 50
50
(JP,KR)60 (JP,KR)
60 (JP,KR)
6060(JP,KR)
3,3
5,6
3,0
5,6
6,9 6,9
6,6
16
1616
16 16
16
(JP,KR)25 (JP,KR)
25 (JP,KR)
13 (UK)
2020(JP,KR)
I
I I
I I
I
X5
X5X5
X5 X5
X5
3,5
3,5
3,5
3,5 3,5
3,5
62
6262
62 62
62
30
3030
30 30
30
2x15
2x15
2x15
2x152x15 2x15
10
1010
10 10
10
1060x705x 1060
1060x705x
1060x705x
x 705 x 758
154
161
173
173
154(5)
5
5 161(5) 5 173(5) 5
6,6
6,6
16
16
13 (UK)
I I
II
X5X5
X5
X5
3,5
3,5
3,5
3,5
6262
62
62
3030
30
30
2x15
2x15
2x15
2x15
1010
10
10
1060x705x
1060x
1560x705x758
175
188
175(5)
173(5)
5
5
76.8
79,9
0.35
0,35
28
83.7
84,4
0.35
0,35
5454
81.4
82,6
0.35
0,35
4141
83,582.6
0,350.35
47 49
83,5
0,35
47
7,9
7,9
1616
83.2
83,5
0.35
0,35
47
47
28(UK)
Please observe the technical data on the rating plate!
GUARANTEE
INSTRUCTIONS FOR DISPOSAL
Our general terms and conditions
apply to the guarantee and
warranty.
Changes in line with technical
innovation reserved.
At the end of the machine's
service life:
ð Remove the mains lead plug.
ð Cut through the mains lead.
ð Take the machine and the
mains lead to your local
electrical appliance recycling
collection point.
13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement