Wells | BMW-206ULST | Specifications | Wells BMW-206ULST Specifications

Wells BMW-206ULST Specifications
011B
WELLS BLOOMFIELD, LLC
10 Sunnen Dr., St. Louis, MO 63143
telephone: 888-356-5362
fax: 314-781-2714
www.wells-mfg.com
OWNERS MANUAL
BUILT-IN
BOTTOM-MOUNT
WARMERS
with
THERMOSTAT
CONTROL
MODELS
BMW206RT, RT6, RTD
BMW206ST, STD
BMW206ULRT, ULRTD
BMW206ULST, ULSTD
BMW206RTD
Includes
INSTALLATION
USE & CARE
EXPLODED VIEW
PARTS LIST
WIRING DIAGRAM
BMW206ULSTD
IMPORTANT: DO NOT DISCARD THIS MANUAL
This manual is considered to be part of the appliance and is to be given to the OWNER or
MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of
this appliance. Additional manuals are available from your WELLS DEALER.
THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR
INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any
questions concerning installation, operation or maintenance of this equipment.
p/n 2M-308014 Rev. (A)
M011B.01
110411
LIMITED WARRANTY STATEMENT
Unless otherwise specified, all commercial cooking
equipment manufactured by WELLS BLOOMFIELD, LLC is
warranted against defects in materials and workmanship for
a period of one year from the date of original installation or
18 months from the date of shipment from our factory,
whichever comes first, and is for the benefit of the original
purchaser only.
THIS WARRANTY IS THE COMPLETE AND ONLY
WARRANTY, EXPRESSED OR IMPLIED IN LAW OR IN
FACT, INCLUDING BUT NOT LIMITED TO, WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE, AND/OR FOR DIRECT,
INDIRECT OR CONSEQUENTIAL DAMAGES IN
CONNECTION WITH WELLS BLOOMFIELD PRODUCTS.
This warranty is void if it is determined that, upon inspection
by an authorized service agency, the equipment has been
modified, misused, misapplied, improperly installed, or
damaged in transit or by fire, flood or act of God. It also
does not apply if the serial nameplate has been removed, or
if service is performed by unauthorized personnel. The
prices charged by Wells Bloomfield for its products are
based upon the limitations in this warranty. Seller’s
obligation under this warranty is limited to the repair of
defects without charge by a Wells Bloomfield factory
authorized service agency or one of its sub-service
agencies. This service will be provided on customer’s
premises for non-portable models. Portable models (a
device with a cord and plug) must be taken or shipped to
the closest authorized service agency, transportation
charges prepaid, for service. In addition to restrictions
contained in this warranty, specific limitations are shown in
the Service Policy and Procedure Guide. Wells Bloomfield
authorized service agencies are located in principal cities.
This warranty is valid in the United States and Canada and
void elsewhere. Please consult your classified telephone
directory, your foodservice equipment dealer or contact:
Wells Bloomfield, LLC
10 Sunnen Dr., St. Louis MO 63143 USA
phone (888) 356-5362 or fax (314) 781-2714
for information and other details concerning warranty.
SERVICE POLICY AND PROCEDURE GUIDE and ADDITIONAL WARRANTY EXCLUSIONS
1.
2.
3.
4.
6.
cleaning schedules, are customer responsibility. Those
miscellaneous adjustments noted are customer
responsibility. Proper attention to preventative
maintenance and scheduled maintenance procedures
will prolong the life of the appliance.
7. Travel mileage is limited to sixty (60) miles from an
Authorized Service Agency or one of its sub-service
agencies.
8. All labor shall be performed during regular working
hours. Overtime premium will be charged to the buyer.
9. All genuine Wells replacement parts are warranted for
ninety (90) days from date of purchase on nonwarranty equipment. This parts warranty is limited only
to replacement of the defective part(s). Any use of
non-genuine Wells parts completely voids any
warranty.
10. Installation, labor, and job check-outs are not
considered warranty and are thus not covered by this
warranty.
11. Charges incurred by delays, waiting time or operating
restrictions that hinder the service technician’s ability to
perform service are not covered by warranty. This
includes institutional and correctional facilities.
SHIPPING DAMAGE CLAIM PROCEDURE
NOTE: For your protection, please note that equipment in
this shipment was carefully inspected and packaged by
skilled personnel before leaving the factory. Upon
acceptance of this shipment, the transportation company
assumes full responsibility for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:
1. VISIBLE LOSS OR DAMAGE: Be certain that any
visible loss or damage is noted on the freight bill or
express receipt, and that the note of loss or damage is
signed by the delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY:
Regardless of the extent of the damage.
3.
CONCEALED LOSS OR DAMAGE: if damage is
unnoticed until the merchandise is unpacked, notify the
transportation company or carrier immediately, and file
“CONCEALED DAMAGE” claim with them. This
should be done within fifteen (15) days from the date
the delivery was made to you. Be sure to retain the
container for inspection.
Wells Bloomfield cannot assume liability for damage or loss
incurred in transit. We will, however, at your request, supply
you with the necessary documents to support your claim.
xi
M011B.01 2M-308014 Owners Manual for Bottom-Mount T’Stat Warmers
5.
Resetting of safety thermostats, circuit breakers, over
load protectors, and/or fuse replacements are not
covered by this warranty unless warranted conditions
are the cause.
All problems due to operation at voltages or phase
other than specified on equipment nameplates are
not covered by this warranty.
Conversion to correct voltage and/or phase must be
the customer’s responsibility.
All problems due to electrical connections not made
in accordance with electrical code requirements
and wiring diagrams supplied with the equipment are
not covered by this warranty.
Replacement of items subject to normal wear, to
include such items as knobs, light bulbs; and, normal
maintenance functions including adjustments of
thermostats, adjustment of micro switches and
replacement of fuses and indicating lights are not
covered by warranty.
Damage to electrical cords and/or plug due to exposure
to excessive heat are not covered by this warranty.
Full use, care, and maintenance instructions supplied
with each machine. Noted maintenance and
preventative maintenance items, such as servicing and
TABLE OF CONTENTS
WARRANTY
FEATURES & OPERATING CONTROLS
PRECAUTIONS & GENERAL INFORMATION
AGENCY LISTING INFORMATION
INSTALLATION
OPERATION
MAINTENANCE INSTRUCTIONS
CLEANING INSTRUCTIONS
TROUBLESHOOTING SUGGESTIONS
WIRING DIAGRAM
EXPLODED VIEW & PARTS LIST
PARTS & SERVICE
CUSTOMER SERVICE DATA
xi
2
3
3
4
6
7
8
10
11
12
16
17
INTRODUCTION
Thank You for purchasing this Wells Bloomfield appliance.
Proper installation, professional operation and consistent maintenance of this appliance will ensure that it
gives you the very best performance and a long, economical service life.
M011B.01 2M-308014 Owners Manual for Bottom-Mount T’Stat Warmers
This manual contains the information needed to properly install this appliance, and to use and care for the
appliance in a manner which will ensure its optimum performance.
SPECIFICATIONS
MODEL
VOLTS
AMPS
WATTS
BMW-206RT
BMW-206RTD
BMW-206ST
BMW-206STD
120 VAC 1ø
10.0A
1200W
208 VAC 1ø
6.0A
1240W
240 VAC 1ø
6.9A
1650W
120VAC 1ø
10.0A
1200W
208 VAC 1ø
6.0A
1240W
240 VAC 1ø
6.9A
1650W
BMW-206ULRT
BMW-206ULRTD
BMW-206ULST
BMW-206ULSTD
1
POWER SUPPLY CORD
NOT SUPPLIED
NOT SUPPLIED
FEATURES & OPERATING CONTROLS
A. THERMOSTAT
1. On THERMOSTATICALLY CONTROLLED warmers, power is
applied to the heating element according to the control knob
position and the actual temperature at the temperature sensing
thermobulb.
2. The desired temperature is controlled by rotating the
TEMPERATURE CONTROL KNOB. The knob has a numeric
scale, where higher numbers correspond to higher temperature.
3. On warmers equipped with an INDICATOR LIGHT, the light will
glow when the thermostat is calling for heat (i.e. the element is
energized).
4. The TEMPERATURE CONTROL KNOB will rotate
approximately 300º, and will reach a “stop” at both ends.
The OFF position is marked.
NOTE: The dial position is an indication of the temperature
setting. Actual temperature will vary depending upon the type of
product and food consistency.
B. MOUNTING
1. Bottom-mounted warmers require that the cutout be flanged to
provide a mounting means.
2. See the Installation Instructions, supplied with the particular
appliance, for details.
C. DRAINS
1. Suffix “D” units (e.g. BMW-206STD) have drains for each pan,
with each pan having an individual drain valve.
M011B.01 2M-308014 Owners Manual for Bottom-Mount T’Stat Warmers
2
PRECAUTIONS AND GENERAL INFORMATION
This appliance is intended for use in commercial establishments
only.
This appliance is intended to hold pre-heated food for human
consumption. No other use is recommended or authorized by the
manufacturer or its agents.
Operators of this appliance must be familiar with the appliance use,
limitations and associated restrictions. Operating instructions must be
read and understood by all persons using or installing this appliance.
Cleanliness of this appliance is essential to good sanitation. Read and
follow all included cleaning instructions and schedules to ensure the
safety of the food product.
Disconnect this appliance from electrical power before performing any
maintenance or servicing.
This appliance is not jet stream approved. Do not direct water jet or
steam jet at this appliance, or at any control panel or wiring. Do not
splash or pour water on, in or over any controls, control panel or
wiring.
Exposed surfaces of this appliance can be hot to the touch and may
cause burns.
Do not operate this appliance if the control panel is damaged. Call
your Authorized Wells Service Agent for service.
The technical content of this manual, including any wiring diagrams,
schematics, parts breakdown illustrations and/or adjustment
procedures, is intended for use by qualified technical personnel.
M011B.01 2M-308014 Owners Manual for Bottom-Mount T’Stat Warmers
Any procedure which requires the use of tools must be performed by a
qualified technician.
This manual is considered to be a permanent part of the appliance.
This manual and all supplied instructions, diagrams, schematics, parts
breakdown illustrations, notices and labels must remain with the
appliance if it is sold or moved to another location.
WARNING:
SHOCK HAZARD
All servicing requiring access
to non-insulated electrical
components must be
performed by a factory
authorized technician.
DO NOT open any access
panel which requires the use
of tools. Failure to
follow this warning can
result in severe electrical
shock.
CAUTION:
RISK OF
DAMAGE
DO NOT connect or energize
this appliance until all
installation instructions are
read and followed. Damage
to the appliance may result if
these instructions are not
followed.
CAUTION:
HOT SURFACE
Exposed surfaces can be hot
to the touch and may cause
burns.
This appliance is made in the USA. Unless otherwise noted, this
appliance has American sizes on all hardware.
AGENCY LISTING INFORMATION
Refer to the product nameplate for the specific appliance for agency
listings. In general:
STD 4
This appliance conforms to NSF Standard 4 for sanitation only if
installed in accordance with the supplied Installation Instructions.
UL Listed warmers are U Listed under UL File E6070.
Underwriters Laboratory recognized (
) warmers (UL File E6070) Since the warmer is only a single component of a complete installation,
the finished installation of an
unit requires additional evaluations to
Underwriters Laboratory standards.
E6070
UL Listed Warmers
E6070
UL Recognized Warmers
3
INSTALLATION
NOTE: DO NOT discard
the carton or other packing
materials until you have
inspected the appliance for
hidden damage and tested it
for proper operation.
Refer to SHIPPING DAMAGE
CLAIM PROCEDURE on the
inside front cover of this
manual.
WARNING:
RISK OF INJURY
Installation procedures must
be performed by a qualified
technician with full knowledge
of all applicable electrical and
plumbing codes. Failure can
result in personal injury and
property damage.
CAUTION
FIRE HAZARD
Avoid storing flammable or
combustible materials in, on
or near the appliance.
Wells Bloomfield does not
recommend bottommounted warmers be
mounted in plastic
counters.
Carefully remove the appliance from the carton. Remove all
protective plastic film, packing materials and accessories from the
Appliance before connecting electrical power or otherwise performing
any installation procedure.
Carefully read all instructions in this manual and the Installation
Instruction Sheet packed with the appliance before starting any
installation.
Read and understand all labels and diagrams attached to the
appliance.
Carefully account for all components and accessories before
discarding packing materials. Store all accessories in a convenient
place for later use.
INSTALLATION NOTES
1.
Installation and start up of built-in warmers MUST be performed
by an authorized installation company.
2. It is the RESPONSIBILITY OF THE INSTALLER to verify that
this warmer installation is in compliance with the specifications
listed in this manual and on the specification sheet provided.
3. It is the RESPONSIBILITY OF THE INSTALLER to check with
the AUTHORITY HAVING JURISDICTION, in order to verify
that this warmer installation is in compliance with local code
requirements.
4. Water supply and drain installation must meet all applicable
local, state and federal plumbing codes and ordinances.
5. Refer to Installation Instructions included with the warmer for
Underwriters Laboratories conditions of acceptability, electrical
requirements and other installation concerns.
BUILT-IN WARMERS
1.
This is a GENERAL GUIDE. For specific cutout dimensions
and other installation details, refer to the Installation
Instructions supplied with the warmer.
2. Cutout dimensions for warmer units and control panels are
listed on the Installation Instructions provided with the warmer.
3. Bottom-mounted warmers require that a flange be formed in
the edge of the cutout as a means of mounting the warmer to
the counter. Verify style of unit (e.g square-corner, radiusedcorner) before making cutout.
NOTE: Cutout dimensions are different for radiused-corner units
(i.e. BMW-206RT) and square-corner units (i.e. BMW-206ST).
Verify the dimensions are correct for the installation before making
the cutout.
4.
For “bottom-mounted” warmers (i.e. warmers mounted to a
formed flange from underneath the counter top), apply a bead
of food-grade silicone sealant to the top inside lip of the pan
prior to attaching to the counter flange.
4
M011B.01 2M-308014 Owners Manual for Bottom-Mount T’Stat Warmers
IMPORTANT: For warmers
installed in plastic counter
tops, the counter material
must be protected from the
heat of the warmer in order to
prevent discoloration and/or
deterioration. Wellsloks are
not suitable for this purpose.
The installer should contact
the manufacturer or distributor
of the countertop material for
specific instructions.
UNPACKING & INSPECTION
INSTALLATION
ELECTRICAL INSTALLATION
1.
2.
3.
Refer to the product nameplate. Verify the electrical service
power. Voltage and phase must match the nameplate
specifications. Wiring the warmer to the wrong voltage can
severely damage the unit or cause noticeably decreased
performance.
Available electrical service amperage must meet or exceed the
specifications listed on the specification sheet provided with the
warmer.
Warmer and control unit must be connected to an appropriate
building ground. Ground connection will be marked “GND” or
”
".
NOTE: Wire gauge, insulation type and temperature rating , as
well as type, size and construction of conduit, must meet or exceed
applicable specifications of local codes and of the National
Electrical Code.
E. PLUMBING INSTALLATION
For use in the State of Massachusetts, this appliance must be
installed in compliance with Massachusetts Fuel Gas and
Plumbing Code CMR 248.
1.
M011B.01 2M-308014 Owners Manual for Bottom-Mount T’Stat Warmers
2.
IMPORTANT: All plumbing installations must be performed by
a qualified plumber.
For units equipped with a DRAIN LINE: Some jurisdictions
may require an approved air gap or other back-flow
prevention device in the drain. It is the responsibility of the
plumber to determine such requirement, to provide and
properly install the required device.
5
NOTE: Damage caused by
leaks due to improper
installation is NOT covered by
warranty.
CAUTION:
SHOCK HAZARD
The ground lug of this
appliance must be connected
to a suitable building ground.
IMPORTANT:
Contact a licensed electrician
to install and connect
electrical power to the
appliance.
IMPORTANT:
Damage due to being
connected to the wrong
voltage or phase is NOT
covered by warranty.
IMPORTANT: Electrical
installation other than as
specified on the specification
sheet will void the UL listing,
and may void the warranty.
NOTE: Plumb connections
must be made in compliance
with all Federal, State and
Local Plumbing Codes and
Ordinances.
OPERATION
CAUTION:
HOT SURFACE
Exposed surfaces can be hot
to the touch and may cause
burns.
CAUTION:
SHOCK HAZARD
DO NOT splash or pour water
onto control panel or wiring.
Always use an inset.
DO NOT place food directly
into the warmer.
Always pour hot water into the
warmer before it is
preheated. DO NOT pour
water into a dry, heated
warmer. This may damage
the unit.
Stir thick food items frequently
to keep food heated uniformly.
Keep insets covered to
maintain food quality and
temperature.
1. Carefully read the description of the warmer operation on the
specification sheet.
2. a. Most warmers are designed for WET OR DRY operation.
b. Warmers may be used wet, or may be used dry. However
warmers may NOT be used wet-to-dry or dry-to-wet unless
they have been allowed to cool to room temperature
between the change in wet or dry operation.
c. Wells Manufacturing recommends operating WET for
consistent food heating.
d. If your wet-operation warmer is allowed to run dry, turn it
OFF and allow to cool to room temperature before adding
water.
3. If the warmer is to be used for WET operation, add
approximately 1” of hot tap water before turning the warmer
ON. Use of hot water will allow a faster preheat.
a. Check the water level frequently and add hot water as
necessary to prevent the warmer from running dry. Do not
add water to the warmer if it has run dry.
b. If your wet-operation warmer is allowed to run dry, turn it
OFF and allow to cool to room temperature before adding
water.
4. Damage caused by allowing a wet-operation warmer to run dry,
is NOT covered by warranty. Damage caused by adding water
to a dry warmer when hot is NOT covered by warranty.
PRE-HEATING THE WARMER
1. Place desired pan(s) or inset(s) with appropriate adapter top on
warmer.
a. Insets are available as accessories in 2½ qt., 4qt., 7 qt.,
and 11 qt. sizes with lids and adapter tops.
b. For dry operation, a 6” deep pan or inset is recommended.
2. Turn temperature control to HI or highest temperature setting.
3. Allow warmer to preheat for approximately 30 minutes, then set
the control for the desired temperature. Be sure to keep the
warmer covered during preheat and operation.
OPERATION
1.
Always use an inset. DO NOT place food directly into the
warmer.
2. Check water level in wet-operation warmer frequently during
use. Running warmers dry will lower the temperature of the
food in the insert pan, and may damage the warmer.
3. Alternating between wet and dry operation in any individual
warmer is NOT recommended.
4. DO NOT use metal tools, steel wool, or caustic or abrasive
cleanser to clean warmer pan.
6
M011B.01 2M-308014 Owners Manual for Bottom-Mount T’Stat Warmers
DO NOT put ice into a
warmer pan. This will cause
condensation on the inside of
the warmer. Damage caused
by condensation is NOT
covered by warranty.
WET OR DRY OPERATION for WARMERS
MAINTENANCE INSTRUCTIONS
CARE OF STAINLESS STEEL
Stainless steel is a marvelous material: strong, lustrous and low maintenance. With a
minimum of care, it will normally retain its beauty and durability for the life of the
equipment. In some applications, however, special care is required in order to maintain
stainless steel’s special properties.
External components, such as cabinets and control panels, are finished with a grain
pattern. This pleasing finish is best maintained by cleaning with a non-abrasive
cleanser applied with a soft cloth. Rub only in the direction of the grain. In the absence
of visible grain, rub only along the longest axis of the appliance.
Restore stainless steel’s luster by applying a polish specifically made for stainless steel.
Spray on, wipe off with a soft cloth, rubbing in the direction of the grain.
Never use metal implements, wire brushes, abrasive scratch pads or steel
wool to clean stainless steel.
Warmer pans, insets and other vessels are subject to a harsher environment. Wells
Manufacturing uses an very high quality stainless steel (#304DDQ) for our food warmer
pans. Even the highest quality stainless steel, however, is mostly iron, and will rust, pit
and corrode under the following conditions:
M011B.01 2M-308014 Owners Manual for Bottom-Mount T’Stat Warmers
•
•
Poor Water Quality: Hard water (water with a high content of dissolved minerals)
will leave mineral deposits when allowed to dry. Calcium (lime) can buildup on
heated surfaces, even under water. If left unattended, hard water spots and lime
buildup can lead to rusting, corrosion and pitting.
Contact with Chlorides: Chlorides (specific compounds of chlorine) are found in
food, table salt and many cleansers. Chlorides can attack the surface of stainless
steel, resulting in corrosion and pitting.
Keep your stainless steel warmers clean and free from calcium buildup.
Use alkaline, alkaline chlorinated or non-chloride cleanser.
Use citric acid-based cleaners to remove calcium deposits.
For additional information, please read the NAFEM Stainless Steel Equipment and
Cleaning Guide. Contact NAFEM at :
North American Association of Food Equipment Manufacturers
401 N. Michigan Avenue
Chicago, Illinois 60611-4267
(312) 644-6610
7
CLEANING INSTRUCTIONS
CAUTION:
SHOCK HAZARD
Do NOT splash or pour water
into or over any control panel
or wiring.
CAUTION:
SHOCK HAZARD
DAILY CLEANING INSTRUCTIONS
PREPARATIONS: Turn control knob(s) to OFF. Allow warmer to cool
before proceeding.
Remove any insets, pans and/or adapter tops.
Drain or remove water from well if used for
wet operation.
FREQUENCY:
Minimum - daily.
TOOLS:
Mild Detergent
Solution: 10 Parts Warm Water to 4 Parts Vinegar
Plastic Scouring Pad
Clean Cloth or Sponge
Food-Grade Silicone Sealant
Disconnect warmer from
electric power before cleaning
CAUTION:
BURN HAZARD
Allow warmer to cool
completely before cleaning.
1. Wipe entire unit down using a clean cloth or sponge and mild
detergent.
2.
Use a plastic scouring pad to remove any hardened food particles
or mineral deposits. IMPORTANT: Do NOT use steel wool for
cleaning.
3.
Rinse warmer thoroughly with a vinegar and water solution to
neutralize all detergent cleanser residue.
4. Inspect warmer flange-to-counter seal. Reseal with food-grade
silicone sealant if necessary. Failure to do so may allow grease and
water to leak into insulation and heating element, causing a potential
fire and/or electric shock hazard.
Inspect warmer tank for damage. Damage to the outer body may
allow grease and water to leak into insulation and heating element,
causing a potential fire and/or electric shock hazard. Contact your
Authorized Wells Service Agency to inspect warmer if water or
grease contamination is suspected.
6.
Close drain valve. Add proper amount of warm water. Turn control
knob(s) ON and check for proper operation.
8
M011B.01 2M-308014 Owners Manual for Bottom-Mount T’Stat Warmers
5.
CLEANING INSTRUCTIONS
WEEKLY CLEANING INSTRUCTIONS
CAUTION:
PREPARATIONS: Remove any insets, pans and/or adapter tops.
Drain or remove water from well if used for wet
operation.
FREQUENCY:
Weekly, or whenever lime or scale is seen
accumulating on the sides of the warmer pans.
TOOLS:
Commercial Delime Cleaner
Plastic Scouring Pad
Clean Cloth or Sponge
1. Add water to pans until water is at normal operating level
(1” - 1 1/2” deep) or covers accumulated scale.
2. Heat water to maximum temperature (190ºF or higher).
3. Pour contents of one package of commercial delime cleaner
into each warmer pan. Stir to dissolve cleaner. Turn heat
control OFF. Cover pans.
4. Allow solution to soak at least one hour, or overnight for heavy
scale buildup.
5. Drain hot water from pans. Scrub with a plastic scouring pad.
Rinse thoroughly with hot water, then dry.
6. Refill pans with hot tap water and resume operation.
M011B.01 2M-308014 Owners Manual for Bottom-Mount T’Stat Warmers
7. Heavy scale buildup may require additional treatments.
9
CHEMICAL BURN
HAZARD
Deilimng chemicals may be
caustic. Wear appropriate
personal protective equipment.
Follow cleaner manufacturer's
instructions for safest use.
TROUBLESHOOTING SUGGESTIONS
SYMPTOM
POSSIBLE CAUSE
SUGGESTED REMEDY
No power to warmer
Circuit breaker off or tripped
Reset circuit breaker
Warmer will not heat
Temperature control not set
Set control to desired
temperature
Wet insulation
Verify flange-to counter seal is
sound, or reseal with food-grade
silicone sealant
Pan leaking or other internal
damage
Contact your Authorized Wells
Service Agency for repairs
Internal damage
Contact your Authorized Wells
Service Agency for repairs
Mineral deposits on pan acting
as a insulator
Clean pan(s) with delime cleaner
Wired to wrong voltage
Verify supply voltage - must
match voltage on warmer
nameplate
Drain valve not fully closed
Check drain valve for debris and
close fully
Warmer trips circuit breaker
Warmer slow to heat
Drain-equipped unit will not hold
water
Drain valve damaged or pan(s)
leaking
Contact your Authorized Wells
Service Agency for repairs
There are no user-serviceable components in this appliance.
In all instances of damage or malfunction, contact your Authorized Wells Service Agency for repairs.
M011B.01 2M-308014 Owners Manual for Bottom-Mount T’Stat Warmers
10
M011B.01 2M-308014 Owners Manual for Bottom-Mount T’Stat Warmers
WIRING DIAGRAM
11
EXPLODED VIEW & PARTS LIST
BMW-206RT, BMW-206RTD, BMW-206ST, & BMW-206STD
2
1
3
12
4
5
11
10
7
9
8
Model: BMW206RT / RTD, BMW206ST / STD
BUILT-IN BOTTOM MOUNT WARMERS w/T-STAT CONTROL
PL011B
IL1881 Rev. B 1/13/2010
12
M011B.01 2M-308014 Owners Manual for Bottom-Mount T’Stat Warmers
6
PARTS LIST
BMW206RT / RTD, BMW206ST / STD
Fig No
Part No
1
P2-31869
WS-503775
Description
SCREEN DRAIN ASSY WARM
PAN ASSY W/O STUDS
BMW206RT
PAN ASSY BMW206RTD
DD-503776
PAN ASSY NO STUD BMW206ST BMW206ST
P2-303777
PAN W/DRAIN BMW206SD
3
2C-30397
CLIP ELEM M P
4
WS-503370
PAN ELEMENT MODS
WS-503774
2
BMW206RT
BMW206RTD
BMW206STD
6
D8-303352
206RTDU, 206STDU, BM206STDL,
BMW206RT, BMW206RTD,
THERMO CTRL, 42" CAPILLARY BMW206RTD120, BMW206RTDU,
W/AUX WARMERS
BMW206SDT, BMW206SDTSAN,
BMW206ST, BMW206STDU,
BMW206STU
206RTD6120, 206RTDU6120,
206STDU6-120, 206SDT6120,
THERMO CTRL 96IN CAP RO
BMW206RT6, BMW206RTD6,
BMW206RTDU6, BMW206SDT6,
BMW206ST6, BMW206STDU6
BRKT THERMO BULB
7
P2-46143
BRKT SHELL MNT BMW206
8
2K-37748X
FTGCONDUIT STRAIGHT 3/8
9
P2-46076
COVER BOTTOM BMW-206 ROH
10
2R-45613
KNOB CONTROL ASSY
11
2J-35687
LIGHT SIGNAL GLO DOT
2N-46131UL
ELEM 120V 1200W BMW206
120V
2N-303375UL
ELEM HEATING 240V 1650W
208/240V
WS-503702
KIT ELEMENT PAN
2T-45917
5
2T-46551
M011B.01 2M-308014 Owners Manual for Bottom-Mount T’Stat Warmers
Application
12
NI
13
EXPLODED VIEW & PARTS LIST
MODELS BMW-206ULRT, BMW-206ULRTD, BMW-206ULST, & BMW-206ULSTD
2
1
3
13
4
12
5
11
9
7
Model: BMW206ULRT / ULRTD, BMW206ULST / ULSTD
BUILT-IN BOTTOM MOUNT WARMERS w/T-STAT CONTROL
PL011B
IL1882 Rev. A 9/9/09
14
M011B.01 2M-308014 Owners Manual for Bottom-Mount T’Stat Warmers
6
10
PARTS LIST
BMW206ULRT / ULRTD, BMW206ULST / ULSTD
Description
SCREEN DRAIN ASSY WARM
PAN ASSY W/O STUDS BMW206RT
PAN ASSY BMW206RTD
PAN ASSY NO STUD BMW206ST
PAN W/DRAIN BMW206SD
CLIP ELEM M P
PAN ELEMENT MODS
THERMO CTRL W/AUX WARMERS
BRKT THERMO BULB
BRKT SHELL MNT BMW206
KNOB ASSY
PANEL FRONT
BRKT MTG THERMO INFINITE
BOX CONTROL
ELEM 120V 1200W BMW206
ELEM HEATING 240V 1650W
KIT ELEMENT KIT
M011B.01 2M-308014 Owners Manual for Bottom-Mount T’Stat Warmers
Fig No
Part No
1
P2-31869
WS-503774
WS-503775
2
DD-503776
P2-303777
3
2C-30397
4
WS-503370
5
2T-45917
6
D8-303352
7
P2-46143
9
2R-40498
10
I7-Z12221
11
P2-40843
12
P2-306959
13
2N-46131UL
13
2N-303375UL
NI
WS-503702
15
Application
BMW206ULRT
BMW206ULRTD
BMW206ULST
BMW206ULSTD
PARTS & SERVICE
Always use an inset.
DO NOT place food directly
into the warmer pan.
DESCRIPTION
PART NO.
ADAPTERS & INSETS
ADAPTER TOP, convert 12” x 20” warmer to
hold two 7 qt. insets
5J-21502
ADAPTER TOP, convert 12” x 20” warmer to
hold two 4 qt. and two 2½ qt
DD-21503
ADAPTER TOP, convert 12” x 20” warmer to
hold three 4 qt. insets
DD-21616
ADAPTER TOP, convert 12” x 20” warmer to
hold one 7qt. and one 4 qt.
DD-21618
ADAPTER TOP, convert 12” x 20” warmer to
hold four 2½ qt. insets
5D-21623
2½ QT. ROUND INSET w/ lid
5D-20773
4 QT. ROUND INSET w/ lid
5D-20774
7 QT. ROUND INSET w/ lid
5D-20587
11 QT. ROUND INSET w/ lid
5D-20908
11 QT. ROUND INSET w/ hinged lid
5D-21057
M011B.01 2M-308014 Owners Manual for Bottom-Mount T’Stat Warmers
16
PARTS & SERVICE
DESCRIPTION
PART NO.
ACCESSORIES
2½ QT. ROUND INSET w/ lid
5D-20773
4 QT. ROUND INSET w/ lid
5D-20774
7 QT. ROUND INSET w/ lid
5D-20587
11 QT. ROUND INSET w/ lid
5D-20908
11 QT. ROUND INSET w/ hinged lid
5D-21057
6 oz. SOUP LADLE
DD-47088
DRAIN VALVE EXTENSION KIT, extension from
drain to counter front with remote handle, for use
with “D” models only, excluding “DM” models
5P-20385
DRAIN SCREEN
5P-21709
M011B.01 2M-308014 Owners Manual for Bottom-Mount T’Stat Warmers
OPTIONAL 72” WIRING, thermostatically controlled
warmers
** contact factory customer service for availability
**
IMPORTANT: Use only
factory authorized service
parts and replacement
filters.
For factory authorized
service, or to order factory
authorized replacement parts,
contact your Wells authorized
service agency, or call:
Wells Bloomfield, LLC
10 Sunnen Dr., P.O.Box 430129
St. Louis MO 63143 USA
Service Dept.
phone: (800) 807-9054
fax:
(314) 781-2714
Service Parts Department can
supply you with the name and
telephone number of the
WELLS AUTHORIZED
SERVICE AGENCY
nearest you.
CUSTOMER SERVICE DATA
please have this information available if calling for service
RESTAURANT _____________________________ LOCATION _____________
INSTALLATION DATE ________________________ TECHNICIAN ___________
SERVICE COMPANY ________________________________________________
ADDRESS ___________________________ STATE ______ ZIP__________
TELEPHONE NUMBER (_____)_____-_________
EQUIPMENT MODEL NO. _______________
EQUIPMENT SERIAL NO. _______________
VOLTAGE: (check one)
120
208
240
17
WELLS BLOOMFIELD, LLC
10 Sunnen Dr., St. Louis, MO 63143
telephone: 800-807-8054
fax: 314-781-2714
www.wells-mfg.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising