Vook | VHD-M1743MX | Installation manual | Vook VHD-M1743MX Installation manual

Vook VHD-M1743MX Installation manual
SMART CENTRE
VIDEO INTERCOM SYSTEM
USERS’ MANUAL
VOOK INTELLIGENT TECHNOLOGY
MANUAL CODE: VHD-M1743MX
Contents
INSTALLATION MANUAL
Cover
Contents
1
Installation Guide
2
Features & Specifications
3
Descriptions for Monitor
4
Descriptions for Doorbell/Camera
5
Wiring Diagrams and Schematics
6-11
Installation
12-13
OPERATION GUIDE
Operation Guide
14
System Settings
15-19
Care Instructions
19
1
Installation Guide
2
FEATURES & SPECIFICATIONS
Features
„ Dual communication & Call Transfer
„ Door Release
„ Image capture (option without memory, 8 or 64 Pictures memory )
„ Picture memories with date and time
„ By no answer, automaticly picture memory
„ TV/MUSIC Playing
„ CCTV Surveillance
„ Supports 2 cameras and 8 Monitors
„ Monitor/Intercom/Broadcast
„ System settable (Time/volume/Brightness/Contrast/Color)
„ Hands free surface/flush mounted, 7 inch TFT Screen
Technical Specifications:
Monitor
Display screen
7 inch TFT
Resolution
> 400 TV lines
Scan frequency
15,625Hz(H)×50Hz(V)
Power voltage
DC 18V 800mA
Video input
75ς 1Vp-p(CCIR standard)
Power consumption
1.5w ~12 w
Wiring mode
4 wires,polar
Dimension
260(W)× 195(H)×44(D)
Doorbell/Camera
Camera
Resolution
Video output
View angle
Min illumination
Night vision light
Power voltage
Power consumption
1/3 inch color
380 TV lines
75ohm 1Vp-p(PAL standard)
78-degree wide-angle camera
0 Lux
6 infrared LED
DC 12v
2w
3
DESCRIPTIONS OF MONITOR
1. LCD Screen
2. Monitor/Answer Button
3. Intercom Button
4. Door Release
5. Adjustment: Left/Right
6. On/Off Button
7. Image Capture
8. Microphone
9. Speaker
10. Siren
11. Indicator
4
DESCRIPTIONS OF DOORBELL CAMERA
1.
2.
3.
4.
5.
Camera
Infrared LED
Call button
Loud speaker
Microphone
5
WIRING DIAGRAMS AND SCHEMATICS
Cable and Connections for Doorbell/Camera
z
z
z
z
1R:
2B:
3Y:
4W:
+12V
GND
VIDEO
AUDIO
power supply positive for Doorbell/camera
power supply ground for Doorbell/camera
image signal transmitting line
talk and control lines
Cable and Connections for Monitor
Connection block CN1:
18V,GND:Terminals for Power Supply Input
Connection block CN2:
12V,GND,AU1,VD1,UNLOCK1+(SDOOR1):
Terminals for Power supply/Ground/Audio/Video/Unlock for the
Doorbell/camera1.
Connection block CN3:
12V,GND,AU2,VD2,UNLOCK2+(SDOOR2):
Terminals for Power supply/Ground/Audio/Video/Unlock for the
Doorbell/camera2.
6
Connection block CN4:
Standby Block
AU3,GND,VD3,GND:
Terminals for Expanded Audio/Ground/Expanded Video/Ground
Connection block CN5:
VD4,VD5,VD6,GND:
Terminals for Expanded Video/GND
Connection block CN6:
+18V,GND,DATA,AU,VD,GND:
terminals for Power+/Power Ground/Data/Audio/Video/Video Ground
System Schematics
2 Cameras, 2 Latches
Multiple Monitors
7
Wiring Diagrams
1 Camera, 1 Latch
1 Monitor
8
Wiring Diagrams
2 Cameras, 2 Latches
1 Monitor
9
Wiring Diagrams
2 Cameras, 2 Monitors,
2 Latches
10
Wiring Diagrams
2 Cameras, 2 Latches
Multiple Monitors
NOTE:
1.The connectors for “+18V & GND” on the connection block CN1 need to be
connected with 18V DC power supply.
2. The 75R Jumping Line for the last extension needs be jumped to the 75Ω
connector
11
INSTALLATION
Installation Instructions
Please see the relevant wiring diagram for the System you have chosen and
ensure you have the correct cable for that systems requirements.
1. Single Monitor Installations:
1.1 Determine both Monitor and Doorbell/Camera operating
positions and heights. (Average height 1.5 to 1.6 Metres).
1.2 Run the appropriate cable between the two positions allowing at
least 350mm excess at each location.
1.3 Unplug the connection terminal from the back of the monitor (Terminal J5).
1.4 Ensure power supply is disconnected at this point.
1.5 Connect cables as per the wiring diagram.
1.6 Re-connect terminal to rear of Monitor.
1.7 Remove top and bottom facia trim for mounting points Install the
monitor to the wall or mounting box if fitted.
1.8 Power up when Doorbell/Camera is fitted.
12
2. Single Doorbell/Camera:
2.1 Please take a moment to select the most suitable Doorbell/Camera position.
2.2 Please consider both daytime, night time and likely weather condition
impact. Direct sunlight on the camera and direct contact with rain
should be avoided.
2.3 Determine Camera Position: Please ensure you run cable through the
camera mounting plate. (Average Height 1.5 to 1.6 metres).
2.4 Surface Mount Doorbell/Cameras require fitting of each cameras mounting.
Please check locating screws in top and bottom of Cameras.
2.5 The Surface Mount Doorbell/Camera has an internal back box that requires
mounting on the wall.
2.6 Please ensure you run the cable through the mounting plate.
2.7 Connect your cable to the Doorbell/Camera following the wiring diagram.
2.8 Affix the Doorbell/Camera onto its mounting plate and secure with locator
screws supplied. Power up Intercom system when all connections are
complete.
13
Operation Guide
14
SYSTEM SETTINGS
At standby mode, press and hold “Photo Button” for 2 seconds to get into the
set-up mode as below.
SYSTEM SETTI NGS
TI ME 10- 20- 05 12: 50: 27
CHI ME TI ME 30S
CHI ME VOL HI GH
TALK VOL HI GH
CHAR ADD ENABLE
I NTECOM SUB
z
z
z
z
z
z
z
z
z
1st line: Day/Mth/Yr & Time for system
2nd line: Chime Duration Time
3rd line: Chime Volume (High/Low/Mute)
4th line: Talk Volume (High/Low)
5th line: Character Add: Enable/Disable
“DOOR1/DOOR2” on monitor screen)
6th line: Main/Sub Multiple Monitor set up
HOLD button 6 on MAIN or SUB for 3 seconds
7th line: Photo Image Enable (optional)
1. Date and Time Setting
The curser flashes at the first character of Day, press “◄► ” (BUTTON 5) to
change value, press BUTTON 6 to move to the next value until both
day/mth/yr and 24 hour clock is set.
Pressing BUTTON 6 will continue your progress through system settings until
Intercom/Main menu. Use “◄►” (BUTTON 5) to select Main or Sub.
At this point, hold BUTTON 6 for 3 seconds, screen will then display the
current setting mode of the photo image function, keep pressing this button
to enable or disable the photo function (only operates if Image memory
option is fitted.
Press “On/Off” (button 2) to “SAVE” system settings. Self turn off after 5
seconds. The system settings will be recorded to memory when power is off.
15
2. Intercom function
In standby mode, a single press of BUTTON 3 from any monitor will call the
other monitors. Extension monitors will chime until any monitor answers by
pressing button 2.
3. Broadcasting function to other monitors
At standby mode, press and hold BUTTON 3 of any monitor to activate the
broadcasting function, while held down talk to all other monitors.
4. Call & Unlock function
When visitors press the Doorbell/Camera, the visitors image of will show on
the Monitor screen. Press BUTTON 2 to stop the chime.
1) You now have 60 seconds talk time (Set as default).
2) You can now talk to your visitor and determine if you wish to operate the
door release if fitted BUTTON 4. The unlock signal will be sent to the
electronic door release continually as long the you press and hold the
“Unlock” key. The shortest unlocking time is 1sec. The Green/Red
Indicator lights will be on when the door is unlocked. Green Light for the
Doorbell/Camera1. Red light for the Doorbell/Camera 2. Door release
button only operates during answering mode ie For security reasons it
cannot be operated at any other time (accidental pressing).
3) If the visitor wants to talk with another person, you may press” Monitor”
button again to hold on, the word “mute” displays on the screen
simultaneously. During this time you may get a chance to ask another
person if he/she would like to answer the visitor. press ” Monitor” button
again getting into the communicating mode.
4) If nobody answers the visitor, the system will stop chiming after preset time
(see system setting). A photo image of the Visitor can be saved in memory if
you have chosen the image store option. If you wish to transfer the visitor to
another person or to another area then the visitor audio video image can be
transferred to another monitor by the procedure below:
Press “call” (BUTTON 3) on the monitor, all other monitors in the system
will receive your call message, eg. “Visitor for John”, John then presses the
answer BUTTON 2 in the nearest monitor to see and talk with the visitor.
16
5. Monitoring function: View Outside from Doorbell/Camera at any time
Press and hold “Monitor” (BUTTON 2) on any monitor will view the outside
images from the Doorbell/Camera. Green & Red lights will display for Camera
1 or 2 respectively. The monitoring time is preset at 30sec.
6. Brightness/Contrast/Colour
In standby mode press BUTTON 2 to display an image, press either
adjustment ” ◄►”(button 5) to adjust the Brightness/Contrast/Color for
the image.
In monitoring mode, keep pressing BUTTON 5 back or forwards to adjust
Brightness. Press BUTTON 7 to move between Brightness Contrast & Colour
Settings.
Br i ght ness
Cont r ast
Col our
7. Adjusting Chime Duration
The chime duration is preset at 30 seconds. If you wish to adjust this time:
The curser flashes at the first character of Day, keep pressing BUTTON 7 to
move to the chime duration setting.
Then press “◄►” *(BUTTON 5) to adjust the chime time. The chime
duration setting is from 10 – 90 seconds.
8. Adjusting Chime Volume
In standby mode, press “answer” BUTTON 2 for 6 seconds, the blue screen
will show the defaulted chime mode. Then press “◄►” (BUTTON 5) to
adjust the chime volume to high, low or mute. E.g. figure below: When the
mute function is on, a red LED will light up on the monitor and the screen
displays the word“mute”. If you are called by other monitors or your visitors
press “call” button on Doorbell/Camera, this monitor will remain mute.
However, the broadcasting function still works when the mute function
activated. Press “hang up” BUTTON 6 to turn off the screen, or it will be
turned off automatically after 5 seconds without pressing any button.
17
CHI ME VOL LOW
CHI ME VOL HI GH
CHI ME VOL MUTE
TALK VOL LOW
TALK VOL LOW
TALK VOL LOW
9. Adjusting Talk Volume
In standby mode, press “answer” BUTTON 2 for 6 seconds, the blue screen
will display the current talk volume. Keep pressing this button to adjust the talk
volume. E.g fig. below:
CHI ME VOL HI GH
CHI ME VOL HI GH
TALK VOL LOW
TALK VOL HI GH
In this mode, with the current setting flashing, press BUTTON 7 to move
adjustment from chime to the talk-setting. The defaulted talk volume is ”HIGH”.
Press “◄►” (BUTTON 5) to adjust. If talk volume “LOW’ is selected, a green
light is displayed. Press BUTTON 6 to save and turn off the screen, or it will
turn off automatically after 5 seconds without pressing any buttons.
10. Character Add
In standby mode, press BUTTON 7 to get into the setting mode, move the
curse to the 5th line, press “◄►” (BUTTON 5) to choose Enable or Disable,
if choose Enable the character “DOOR1” or “DOOR 2” will display on the
monitor screen. If choose Disable, the monitor screen will not display any
characters.
11. Intercom SUB or MAIN
If more than one Monitor installed, one Monitor should be setup as MAIN, or
other should be setup as SUB.
18
12. Photo Function ( VHD-M1743M8 , VHD-M1743M64 )
When visitor press BUTTON 3, if there is no answer from the
Monitor/Monitors after 10 seconds, the photo function will take an image of
the visitor and store it for later viewing. The date / time is also stored. Up to 64
images ( VHD-M1743M64 ) can be stored. As new images are stored old
images are deleted.
13. Audio/Video Function
If fitted cameras with audio function for baby-rooms and connected the
audio/video wires with monitors, in standby mode, press BUTTON 2 of any
monitors for 3 times activating the Audio/Video Function to monitor the
baby-rooms.
14. Video expanded function
Besides 1 Audio/Video channel, this intercom also can be expanded 3 video
channels to monitor home status via fitted camera. In standby mode, keep
pressing button2 to monitor door1, door2, audio/video channel1, expanded
video channel1, expanded video channel2, expanded video channel3.
15. System Time
Entering set-up mode (press and hold Button 7) the power out time will remain
in the display. However, the time and date clock will still run in the
background.
Exit set-up mode and re-enter set-up mode and the current time will be
displayed.
CARE INSTRUCTIONS
1)
2)
3)
4)
Please ensure you use the recommended cable for the conditions set
out in this guide.
Do not use cleaning agents or solvents on the Screens of these
products. Use a moist damp cloth and gently wipe lens surfaces
outwards.
Image distortion may occur if your equipment is mounted too close to
magnetic field e.g. Microwaves, TV, Audio equipment or speakers.
The Doorbell/Camera should be fitted with an approved weather shield
if the position chosen is in direct sunlight, or in contact with rain, snow or
irrigation sprinkler systems.
19
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising